Note: Your remote control will not lose its settings when the batteries are out of power. When changing the batteries, do not press any key on the remote control or the remote controls settings will be affected.
9 Copyright Lexibook 2008

ST400IM0148_new.indd 9

3/4/08 10:12:29

English

Settings
Once you complete the setup procedure, the Lexibook Universal 4 in 1 remote control will allow you to control the various audio-video devices you have use by pressing the corresponding device key (TV, DVD, SAT or VCR). There are 3 programming methods: the Hot Brand code search, the Manual set-up and the Quick/Automatic programming. Please refer to the code list p.11 and at the end of this manual. Please always try the Hot Brand code search FIRST, then if no code in the list of brands and models matches your device, try the Manual set-up, and only if this one fails, try the Quick/Automatic programming. Warning: program one appliance at a time. For example, start by setting your remote to your TV, then to your DVD player
9. Try some keys on your remote control to check if they work properly. If they do, your settings were successful: you found the right code. You are now ready to set another device, with the same procedure. Note: correct code. Try the Hot brand search again or use another programming method. You can press the EXIT key at anytime to stop the search. The codes previously stored wont be lost or changed.

HOT BRAND LIST

Hot Brand code search
There are 20 of the most popular TV brands and 10 brands for the DVD, VCR and SAT listed in the Hot brand list. If the brand of the device you want to program on the remote control is in the list, you should be able to make the settings quickly. Please follow the instructions below: 1. Select the device you wish to set (ex.: TV). Search your devices brand in the code list attached p.11. There is a different code list for each of the 4 devices which your remote control can be set to. Mark down the corresponding 1-digit code or 2-digit code (for example, if your TV brand is PHILIPS, the correct code is 00, if your VCR brand is SONY, the correct code is 2). 2. Switch on the device you want to control with the remote and aim the remote at the device. - If its a VCR, insert a video tape. - For SAT, select a program. - If its a DVD player, insert a DVD. 3. Press and hold the key of the device for 3 seconds. The LED located on the top part of the remote will turn on and then turn off after 3 seconds. 4. Release the key. The LED lights up again. 5. Use the numeric keys to enter the 1-digit code (VCR, DVD or SAT) or the 2-digit code (TV) applicable for your device. beginning of the code search. 7. When the device turns off, turns on, mutes or changes channels, the correct code has been found. Press the device key once again to store the code and exit the search mode.

10 Copyright Lexibook 2008

ST400IM0148_new.indd 10

Manual set-up
The Manual set-up or direct code entry allows you to enter directly the code number of the device you want to control with the remote. Please follow the instructions below: 1. Select the device you wish to set (ex.: TV). Search your devices brand in the code list attached p.X. There is a different code list for each of the 4 devices which your remote control can be set to. Mark down the corresponding 3-digit code. One brand may have up to 30 codes. You might have to try several of have to repeat the full procedure. 2. Switch on the device you want to control with the remote and aim the remote at the device. - If its a VCR, insert a video tape. - For SAT, select a program. - If its a DVD player, insert a DVD. 3. Press and hold the key of the device for 3 seconds. The LED located on the top part of the remote will turn on and then turn off after 3 seconds. 4. Release the key. The LED lights up again. 5. Press the Power key , then use the numeric keys to enter the 3-digit code applicable for your device.

Automatic (Auto) search

This search should be used only if the Hot brand code search and the Manual set-up have both failed or if the brand or correct model code are not listed in the code list at the end of the instruction manual. corresponding to the selected device. 1. Switch on the device you want to control with the remote and aim the remote at the device. - If its a VCR, insert a video tape. - For SAT, select a program. - If its a DVD player, insert a DVD. 2. Press and hold the key of the device for 3 seconds. The LED located on the top part of the remote will turn on and then turn off after 3 seconds. 3. Release the key. The LED lights up again. A new code is sent by the remote control every second. 5. When the device turns itself off, the correct code has been found. Press the device key right away to store the code and exit the search. 7. Try some keys on your remote control to check if they work properly. If they do, your settings were successful: you found the right code. You are now ready to set another device, with the same procedure. If your remote controls keys program it again.
times then remains on. You must enter a new code. 7. Try some keys on your remote control to check if they work properly. If they do, your settings were successful: you found the right code. You are now ready to set another device, with the same procedure. code and you need to try the next 3-digit code corresponding to your devices brand in the list. Repeat steps 3 to 7 until your device responds correctly to the keys pressed on the remote. Note: After pressing the Power key (step 5), press the EXIT key at anytime to stop the search and exit the manual set-up mode. The codes previously stored wont be lost or changed. If no key is pressed for more than 15 seconds, the setup ends automatically and the LED goes off.

Quick search

Use the Quick search if you didnt have the time to store the correct code during step 5 of the Auto search. 1. Press the Pause key during the Auto search to enter the Quick search mode. The LED remains on. CH key to start the Quick search: the device you want to program 2. Press the _ on the remote control should turn on. _ 3. If the device does not turn on, press the CH key every 2 seconds until it does. 4. When the device turns on, the correct code has been found. Promptly press the corresponding device key on the remote control to store the code and exit. Note: If you accidentally pressed on the _ key after the device has turned on, + press on the CH key right away and wait for 2 seconds to see if your device turns off.

ST400IM0148_new.indd 11

3/4/08 10:12:30
6. Check whether all applications of your device can be operated with the remote control keys. You are now ready to set another device, with the same procedure. code and you need to try to program it again.
1. Press and hold the key of the device you have programmed on the remote control for 3 seconds. The LED located on the top part of the remote control will turn on and then turn off after 3 seconds. 2. Release the key. The LED lights up again.
Tips for Auto and Quick search modes
You can exit the Auto and Quick search modes at anytime by pressing the In Auto search mode, the remote control searches the correct codes very quickly and you may not have enough time to store them (step 5 of the Auto search mode). It is recommended to use both the Auto search and the Quick search methods by pressing on the Pause key. When the correct code has been found, if the original remote control of the device you want to control with the ST400 didnt have a Power key, the device may not turn off but play, change channels or the sound will go off. end of the code list, and then remains on. You can browse through the tables + using the Fast Forward , Fast Rewind , CH and keys CH. _ If no key is pressed for more than 15 seconds, the setup procedures stop automatically, but the codes stored will not be lost or changed. In Auto search mode, all the function keys except the Pause , EXIT, TV, DVD, VCR and SAT keys can be pressed without exiting the mode. In Quick search mode, all the function keys except the Pause , EXIT, + Fast Forward , Fast Rewind , CH , CH , TV, DVD, VCR and SAT keys _ can be pressed without exiting the mode. During the Auto search mode, press the Pause key once to enter the Quick search mode. Press the same key once again to go back to the Auto search mode. In Quick search mode, the search direction can be changed by pressing: the Fast Forward key (transmits the next 10 codes, then stops), the Fast Rewind + key (transmits the previous 10 codes, then stops), the CH key (transmits _ the next code then stops), the CH key (transmits the previous code then stops). below. Example: eight times.

Important note:

Storing your favourite channels and child lock function
The FavCH key allows you to store your favourite channels or limit the number of channels accessible to your children (child lock function). You can store up to 15 of your favourite channels by sequences of 6 numbers. Store your favourite channels Example: Store channels 5, 21 and 147. 1. Press the desired device key. 2. Press and hold the FavCH key for 3 seconds. The LED will turn on and then turn off after 3 seconds. 3. Release the FavCH key. The LED lights up again. 4. Then one key after another, press:
5 FavCH -/-FavCH -/-7 FavCH
Noting the programmed code
Once youve programmed the ST400, please always note the 3-digit code(s) operating your device(s). This may be useful if you need to reprogram your remote control in the event of accidental cancellation or when you change used batteries. When searching the code, the LED will display the code by slowly
Once you have noted the code displayed, you can use the Manual set-up method to reprogram the desired device.
The channels will be automatically stored when you press the sixth digit or you can also press the FavCH key to end the sequence and save your favourite channels.

ST400IM0148_new.indd 12

3/4/08 10:12:32
Note: when you are storing your favourite channels, only the EXIT, FavCH, -/-quickly 4 times and will remain on until you press a valid key. on. Repeat the procedure above to store new channels. 6. Press the EXIT key to exit the mode. 7. Once you have stored your favourite channels, simply press the FavCH key to browse through the channels in the order they were stored and select one of them. Note: goes off. The programming is cancelled. To delete the channels from the memory: 1. Press the desired device key (ex: TV). 2. Press and hold the FavCH key for 3 seconds. The LED will turn on and then turn off after 3 seconds. 3. Release the FavCH key. The LED lights up again. 4. Press the device key twice (ex: TV TV).
Basic volume lock ( punch through ) + CH This feature allows you to use the volume keys ( CH , _ and Mute ) of your last active TV or audio device while in VCR, DVD or SAT/CBL mode without changing to TV or audio mode. For example, you can watch a DVD and control the volume (a TV function) without pressing on the TV key. Note: The volume lock feature is automatic. You can use the volume keys without exiting the current mode. If a device has its own volume keys settings or data (such as some satellite receivers), the volume lock feature will not be activated. Advanced volume control (volume lock) As mentioned above, the volume lock feature is automatic, but you can choose to control the volume of one device through the volume of another device. Example: to control the volume of device 1 (ex. your DVD) through the volume of device 2 (ex. your TV). 1. Press and hold the Mute key, the LED lights up. 2. Without releasing the Mute key, press the DVD key. 3. Without releasing the Mute key, press the TV key.

Child Lock In Child Lock mode, the
and numeric keys are not active.
1. Press and hold the FavCH key for 3 seconds. The LED will turn on and then turn off after 3 seconds. 2. Release the FavCH key. The LED lights up again. 5. To cancel the setting and go back to the Basic volume lock, press and hold 3. Use the numeric keys to enter 9, then press the FavCH key once again. the DVD key for 3 seconds. The LED lights up then goes off after 3 seconds. 6. Release the DVD key. The LED lights up again. Note: Repeat steps 1 to 3 to switch off the child lock mode.

Special features

Transport keys lock This feature allows you to use the Play , Pause , Stop , Record , Previous , Next , Fast forward and Fast rewind keys (transport keys) of your last active VCR, DVD or CD device while watching the TV or a satellite/cable channel without changing to DVD/CD or VCR mode. For example, you can watch the TV and use the transport keys to control your DVD player without pressing the DVD key on the remote control. Note: The transport keys lock feature is automatic. You can use the transport keys Copyright Lexibook current mode. without exiting the 2008

ST400IM0148_new.indd 13

lock has been reactivated. All off feature Press the Power key twice to switch off all the devices controlled by the ST400. Press once again to switch back on all the devices. Note: To use this feature, make sure that: No other remote control is being used to switch on or switch off the target devices. All the devices are in the line of sight. The Auto code search and Hot brand code search are not being performed. That 2 devices or more are not using the same code.

3/4/08 10:12:33

If a device has its own transport keys settings or data (such as some satellite receivers), the transport keys feature will not be activated.
Quick view This feature allows you to quickly browse through the channels without programming them manually. 1. Press and hold the or keys for 3 seconds. The LED lights up then goes off after 3 seconds. + _ 2. The remote control will change channel up ( CH ) or down ( CH ) every 1,5 seconds until you press another key.

Warranty

This product is covered by our two-year guarantee. For all matters relating to the guarantee or our after-sales service, please contact your retailer and have your receipt on hand. Our guarantee covers manufacturing or assembly defects with the exception of all damage resulting from a failure to respect the instructions, or any inappropriate handling of the article (such as taking it apart, exposing it to heat or humidity, etc). Note: It is recommended that all packaging be kept for future reference. Keep this instruction manual in a safe place as it contains important information. In our constant concern for improvement, the colours and details of the product may differ slightly from those shown on the packaging. Reference: ST400 Designed and developed in Europe Made in China 2008 LEXIBOOK LEXIBOOK UK ltd