Notes:
If you want to print a photo while using the control panel, a photo storage device
must be inserted in, or connected to, the printer.
The printer will not read a memory card if a second memory card or a USB flash
drive is inserted, if a PictBridge-enabled digital camera is connected, or a camera phone is detected. Memory card
Insert the card with brand name label facing up. If there is an arrow on the card, make sure it points toward the printer. Insert only one memory card at a time.

Bluetooth adapters

An adapter is not included with the printer. Consult the Lexmark Web site at www.lexmark.com for late-breaking
information about supported Bluetooth adapters.
Follow the instructions provided with your Bluetooth-enabled device to view and

print photos. CD

Insert only one CD into the drive at a time. Consult the Lexmark Web site at www.lexmark.com for late-breaking
information about supported CDs.

USB flash drive

An adapter may be necessary if your USB flash drive does not fit directly into

the PictBridge port.

Consult the Lexmark Web site at www.lexmark.com for late-breaking
information about supported USB flash drives. PictBridge enabled digital cameras or camera phones
Make sure the PictBridge-enabled digital camera or camera phone is set to the
correct USB mode. For more information, see the camera or camera phone documentation.
Follow the instructions provided with your camera or camera phone to operate

the printer.

Finding information about the printer

Setup sheet

Description Where to find
The Setup sheet gives you instructions for You can find this document in the setting up hardware. printer box or on the Lexmark Web site.
Description The User's Guide gives you instructions for using the printer and other information such as: Where to find You can find this document in the printer box or on the Lexmark Web site.
Maintenance Troubleshooting Safety

Web site

Description Our Web site contains a variety of information. Note: All paths for the Web site are subject to change. Where to find Visit our Web site at www.lexmark.com.

1 Go to the Web site. 2 Select a language from the drop-down
list in the upper-right corner of the page.
3 Select the link for the information you
Record the following information (located on the store receipt and the back of the printer), and have it ready when you contact us so that we may serve you faster: Machine Type number: Serial number: Date purchased: Store where purchased:
Understanding the printer
This compact printer is a standalone device that can be used to:

View Print Save

photos.

Printer parts

Use the 5 Paper support Access cover Memory card slots Paper exit tray CD drive
To Load paper. Access the print cartridge. Insert memory cards. Stack paper as it exits. Insert a CD in the CD drive.
Use the PictBridge port Power button
To Connect a PictBridge-enabled digital camera or USB flash drive to the printer. Turn the printer on and off. Use to turn the printer on and off.
Note:.After the printer is idle for five minutes, the ink level screen appears. 8 Control panel Operate the printer. Before attempting to use the control panel, be sure printer is on. 9 Display panel buttons. on the front of the
Raise the display to access the control Adjust the angle of the screen for viewing. View menus, settings, messages, and
Use the buttons on the control panel to

select options.

Use the 3 Power connector Video output port Bluetooth port
To Connect the printer to a power source. Connect a TV to the printer using a super video cable. Connect a Bluetooth adapter (only) to the printer.

Using the control panel

If you want to print a photo while using the control panel, a photo storage device must be inserted in or connected to the printer. Note: The availability of some of these functions depends on your place within the menu you have selected.

Press Right

Scroll through menus or menu options. Change settings on a submenu item. Display the previous or next picture.

Left Select

Select a menu or menu option. Select or clear a photo from the list to be printed. Apply a photo-editing feature.

Previewing photos

1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press 4 Press 5 Press 6 Press
or. or to view the photos. until View & Print appears.
to return to the previous display.
Selecting and printing photos
You can select specific photos to print from a photo storage device.
1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press 4 Press 5 Press
or until View & Print appears.
twice. or to browse the photos.
to select a photo. to print them.
You can select multiple photos before you press

Printing an index page

Print an index page showing all of the photos on a photo storage device. When copying your photos to a CD, store the index with the CD.
Note: Digital Print Order Format (DPOF) is a feature available on some digital cameras and camera phones. Index print is not available if the photo storage device contains a DPOF file.
1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press
until Print All / Index appears.
If there is no DPOF information on the photo storage device, the following message appears on the display: Would you like to print one photo per page, or an index page with thumbnails?

4 Press 5 Press 6 Press

to choose Index Page. to begin printing.
Printing all photos from a photo storage device
until Print All / Index appears. to print each photo on its own page. to begin printing.
Printing multiple copies of a photo
You can print from one to ten copies of each image.
1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press 4 Press 5 Press 6 Press 7 Press 8 Press 9 Press 10 Press 11 Press
. or. or. to change the number of copies. until Copies appears. or. or to browse the photos. until View & Print appears.

to select a photo.

You can select multiple photos and adjust the number of copies for each photo before you press to print them.
Changing the print quality
1 From the main screen, press 2 Press
. or until Setup appears.
3 Press 4 Press 5 Press 6 Press 7 Press

or. or.

until Print Quality appears.
until the quality you want appears.
Selecting and editing photos
You can choose from any of the available editing options, such as zooming in on a particular area in the photo, adjusting the brightness, removing red eye, or other color effects to edit the photos before printing or saving. All photos selected remain selected until you deselect them or remove the camera card, USB flash drive, or CD. when the photo you You can also select photos during a slide show by pressing want appears on the screen. When the slide show is complete, return to the View & Print menu to print them or to the Save / Copy menu to copy them to a CD or a USB flash drive. Note: The changes you make to the photos will only appear on your prints. They are not saved to the original image file. To save your changes, copy the photo from your camera card to a writable photo storage device, such as a CD or USB flash drive, once changes have been made.

Adjusting the print area

You can adjust the area of your finished prints. Notes:
Make sure a photo storage device is inserted in the printer. For more information,
see Using photo storage devices on page 27.
The changes you make for the prints are not automatically saved after printing.
Use writable photo storage devices, such as a CD or USB flash drive, to save any changes to the images. Cropping, moving, rotating, or zooming the print area
or. until View & Print appears.
A menu of options appears.
. or repeatedly until the photo you want to adjust appears.

7 Press

Crop & Zoom appears.

8 Press

9 Press repeatedly to select one of the following: Rotate to change the photo from portrait to landscape Zoom-In/Zoom-Out to enlarge or reduce part of the photo Left/Right to horizontally change part of the photo Up/Down to vertically change part of the photo 10 Press
or to change the print area.
11 Repeat steps 8 and 9 until the print area appears as you want it. 12 Press 13 Press
Note: You can edit more photos before printing.
Adjusting the appearance of photos
You can adjust the appearance of your photos to remove red-eye, change brightness, and make other changes before printing.
1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press 4 Press 5 Press 6 Press 7 Press 8 Press 9 Press
display. or. or until the option you want appears, or follow the prompts on the until the option you want appears. or until View & Print appears.
twice. or. repeatedly until the photo you want to adjust appears.

10 Press 11 Press

. to return to the previous display.
12 Continue to select and edit all of the photos you want to print. 13 Press

to print.

Note: You can change multiple photos before printing. Enhancing photos To enhance the details or adjust the brightness of a picture in one step:
. or. or until On, Off, or Manual appears. or to move the slider and adjust the brightness. until Image Enhance appears. or until View & Print appears.
If you select Manual, press
10 Press 11 Press 12 Press
. to return to the previous display. to print your photos.

Removing Red Eye

1 Insert a memory card, CD, or USB flash drive. 2 Press 3 Press 4 Press
twice. or repeatedly until the photo you want to adjust appears.

5 Press 6 Press 7 Press 8 Press 9 Press 10 Press 11 Press 12 Press

until Red Eye appears.

until On appears.
to return to the previous display. to print your photos.

Using Color Effects

The Color Effects feature lets you print in tones of Sepia, Antique Brown, Antique Gray, or black and white (B/W). Note: This setting remains in effect only for the current printing process.
. until Color Effects appears. or until View & Print appears.

to choose a photo.

or until the option you want appears: Off, B/W, Sepia Tone Print, Antique Brown, or Antique Gray.

10 Press

11 Press 12 Press
to return to the previous display. to begin printing.
Note: You can select and edit more photos before printing.

Viewing a slide show

Viewing a photo slide show
You can view a slide show of the photos saved on a photo storage device.
1 Insert a memory card, CD, or USB flash drive; connect a PictBridge-enabled
digital camera; or make sure a Bluetooth adapter is attached.
2 Press 3 Press 4 Press 5 Press 6 Press
repeatedly until Slide Show appears. , and then press to
to view the photos on the display, or press view the photos on your TV. to begin the slide show.
to pause to continue to select a photo to rotate Note: When you have completed viewing the slide show, return to the View & Print menu to print any selected photos, or go to the Save / Copy menu to copy the selected photos to the USB flash drive or to the CD.

Video output

The printer lets you view the photo slide show on the printer display on your TV screen. To connect a TV to the printer, use a video cable and the video port located on the back of the printer. Note: Make sure you select the correct video output type from the Setup menu. For more information, see Navigating the display menus on page 13.
Using photo storage devices
You can use several kinds of photo storage devices to work with photos.
See the section on the device you want to use for instructions on its use. To select and print photos from a photo storage device, see Selecting and
printing photos on page 17. Note: The printer will not read a memory card if a second memory card is inserted, or if a PictBridge-enabled digital camera is connected.

Inserting a memory card

1 Locate the memory card slots on the right front of the printer. 2 Insert a memory card into the appropriate slot. Insert the card with the brand name label facing up. If there is an arrow on the card, make sure it points toward the printer. Insert only one memory card at a time.

Slot Top slot Bottom slot

Memory card CompactFlash

Memory Stick (MS) Memory Stick PRO MultiMedia Card (MMC) Secure Digital (SD) SmartMedia Note: Be sure the gold contact area faces up. Insert the card all the way in quickly.

Bottom slot with adapter

xD Picture Card Memory Stick Duo Mini SD RS-MMC TransFlash
Note: Be sure to connect the memory card to the adapter that came with it before inserting it in the slot.
3 Wait for a small light on the card reader to come on. The light blinks to indicate
the memory card is being read or is transmitting data. If the printer does not read the memory card, remove and reinsert it.
Inserting a USB flash drive
1 Insert the USB flash drive into the PictBridge port on the front of the printer.
An adapter may be necessary if your USB flash drive does not fit directly

into the port.

The printer reads only one photo storage device at a time. 2 Wait for the light on the printer to come on. The light blinks to indicate the flash
drive is being read or is transmitting data. Copying photos to the USB flash drive
1 Insert a USB flash drive. 2 Insert a memory card or CD. 3 Press
or until Save / Copy appears.
Note: If you edit photos before copying to the USB flash drive, the changes are saved with the photo.

4 Press 5 Press

. or. until Copy to CD or USB appears.
6 To copy all photos, press
. , and then select all the photos you want to
To copy selected photos, press copy by pressing.

Ready to Copy? appears.

The photos are copied to the USB flash drive.

9 Press

to select Finished.

Using the CD drive

You can print photos from a CD, save photos to a CD, and view photos stored on a CD. You can use a CD as a source for a slide show. Your printer has been designed to work with standard high quality CD-R media. Look for the following symbol when purchasing CDs for use with this printer:

Inserting a CD into the CD drive
1 Press the button on the front of the CD drive to open it. 2 Insert a CD.
3 Gently push the CD drawer toward the printer to close it.
A light flashes to indicate that the CD is being read.

Copying photos to the CD

1 Insert a CD. 2 Insert a memory card or USB flash drive. 3 Select Yes when asked begin using USB?. 4 Press
Note: If you edit photos before copying to the CD, the changes are saved with the photo.
5 Press 6 Press 7 Press 8 Press
. or. to choose Copy All # Photos or Select Photos.
The photos are copied to the CD.
to choose Copy to Another or Finished.

twice.

Print an index page to store with your CD. For more information, see Printing an index page on page 17.
Printing directly from digital cameras, mobile phones, and PDAs
With direct printing, photos are selected on the display of the camera, mobile phone, or PDA. The printer is operated from the camera, phone, or PDA. The operator panel of the printer is not needed. When printing from mobile phones and PDAs, it is sometimes necessary to select a printer type. If prompted, select HP 995C.
Printing from mobile phones
This Mobile Printing Ready product is designed to provide easy printing from mobile phones. This product follows Mobile Imaging and Printing Consortium (MIPC) Implementation Guidelines for Home Printing with Terminals, Version 1.0, for Bluetooth, PictBridge, and memory cards. See the documentation that came with your mobile phone for printing instructions.
Bluetooth wireless support
Insert a USB Bluetooth adapter into the USB port located on the rear of the printer.
Note: An adapter is not included with the printer. Turning Bluetooth Mode On or Off This option lets you choose whether Bluetooth Mode is on.
1 Press 2 Press 3 Press 4 Press 5 Press

until Setup appears.

until Bluetooth Mode appears. or until Non-Discoverable or Discoverable appears.
Off means that Bluetooth is off. Discoverable means that Bluetooth is on. The printer looks for other units
and can be found by other units.
Non-Discoverable means that Bluetooth is on. The printer looks for other
units but cannot be found by other units.

6 Press 7 Press

. to exit the Setup menu.
Locating the Device Name and Universally Administered Address (UAA) This option lets you view the Device Name and UAA number automatically assigned for Bluetooth devices. You may do this to determine the factory assigned name or UAA number to assign to it for your mobile phone or personal digital assistant (PDA). Some mobile devices display the UAA number instead of a name. Note: The device name and UAA number cannot be changed.

Note: Photo paper and other supplies are also available on the Web site.
Removing a used print cartridge
1 Make sure the printer is on. 2 Lift the access cover.
The print cartridge carrier moves and stops at the loading position, unless the printer is busy.
3 Press down on the cartridge lever to raise the cartridge lid.
4 Remove the used print cartridge.
Installing a print cartridge
1 Remove the sticker and tape from the back and bottom of the cartridge.
Warning: Do not touch the gold contact area on the back or the metal nozzles on the bottom of the cartridge.
2 Insert the cartridge in the carrier.

3 Snap the lid closed.

4 Close the access cover.
Do you want to align the cartridge? appears.

5 Press

to accept Yes.
Aligning the print cartridge Align the print cartridge when you:
Have installed a new cartridge Want to improve print quality 1 Press 2 Press 3 Press 4 Press 5 Press 6 Press 7 Press
or. or. to accept Align. to accept Done. to return to the previous menu. until Align Cartridge appears. until Setup appears.
If you aligned the cartridge to improve print quality, print your photo again. If print quality has not improved, clean the print nozzles. For more information, see Cleaning the print cartridge from the control panel on page 39. Cleaning the print cartridge from the control panel Clean the print cartridge when you:
Notice blank or faint areas in the printing Want to improve print quality 1 Press 2 Press 3 Press 4 Press 5 Press 6 Press
or. or. to accept Clean. to accept Done. until Clean Cartridge appears. until Setup appears.
7 Print your photo again.
If print quality has not improved, continue with the following procedure. Wiping the print cartridge nozzles and contacts Wipe the print cartridge nozzles and contacts when you:
Notice blank or faint areas in the printing Want to improve print quality 1 Remove the print cartridge. For more information, see Removing a used print

cartridge on page 37.

2 Dampen a clean, lint-free cloth with water. 3 Gently hold the cloth against the nozzles for about three seconds, and then wipe

in the direction shown.

4 Using another clean section of the cloth, gently hold the cloth against the
contacts for about three seconds, and then wipe in the direction shown.
5 With another clean section of the cloth, repeat step 3 and step 4. 6 Let the nozzles and contacts dry completely. 7 Reinsert the print cartridge. 8 Close the access cover. 9 Clean the cartridge by selecting Clean Cartridge from the control panel. For
more information, see Cleaning the print cartridge from the control panel on page 39.

3 Plug the cord into an electrical outlet that other electrical devices have been

using.

4 If the power button light is not on, press
Incorrect language appears on the display
Note: You choose the language the first time you turn on the printer, but you can change it at any time.

1 Press 2 Press

to turn the printer off. to turn the printer on. twice.
3 From the control panel, press 4 Press 5 Press 6 Press 7 Press 8 Press

. ten times. or.

until the language you want appears.
Page does not print or printer does not respond
If an error message appears, see Error messages on display on page 47. If the Power button light is not on, see Power button is not lit on page 43.
Make sure a cartridge is in the printer. Remove and then load paper. Check the ink level, and install a new print cartridge if necessary.
1 Remove the print cartridge. For more information, see Removing a used print
2 Make sure the sticker and tape have been removed.
3 Reinsert the print cartridge. For more information, see Installing a print

cartridge on page 38.

1 Press

to turn the printer off.

2 Disconnect the power supply cord from the wall outlet. 3 Gently remove the power supply from the printer. 4 Push firmly to reconnect the power supply to the printer. 5 Reinsert the power supply cord into the wall outlet. 6 Press

Poor photo quality

Examples of poor photo quality include:
Blank pages Dark print Faded print Incorrect colors Light and dark bands in print
Skewed lines Smudges Streaks White lines in print
Check the ink level, and install a new print cartridge if necessary. Use a different brand of paper. Each paper brand accepts ink differently and prints with color variations. Use only new, unwrinkled paper.
Poor quality at the edges of the page
Be sure the paper size you are using is the same as the paper size you have selected from the control panel. For more information, see Selecting the paper size on page 16.

Paper jam

to turn off the printer.
2 Firmly grasp the paper, and gently pull it out. 3 Press
to turn the printer back on.

Paper misfeeds

If paper misfeeds or skews, or multiple sheets feed or stick together, try the following solutions. Load a smaller amount of paper into the printer. Load paper with the print side facing you. Remove each page as it exits, and let it dry completely before stacking. Use only new, unwrinkled paper.
Printer does not feed paper
Check for a paper jam. For more information, see Paper jam on page 46.
Try loading one sheet at a time.
Photo storage device troubleshooting
Memory card cannot be inserted on page 47 Nothing happens when a memory card is inserted on page 47 Error messages on display on page 47 PictBridge-enabled device not recognized on page 47 Cannot print from PictBridge-enabled devices on page 48

Memory card cannot be inserted
Make sure that the type of memory card you are using can be used in the printer. For more information, see Inserting a memory card on page 27.
Nothing happens when a memory card is inserted
Remove and reinsert the memory card. Make sure that the type of memory card you are using can be used in the printer. For more information, see Inserting a memory card on page 27. See Inserting a memory card on page 27 to determine which slot accommodates your memory card and to see instructions on how to insert it. Check that there is no obvious damage to the memory card or slots on the printer. Insert only one memory device at a time. Disconnect the PictBridge-enabled digital camera from the printer.
Error messages on display
If an error message is displayed, follow the instructions on the display, or see Error messages on page 48.
PictBridge-enabled device not recognized
Connect a PictBridge-enabled device to the PictBridge port. See the documentation that came with your device to determine whether it is PictBridge-enabled.
Cannot print from PictBridge-enabled devices
Enable PictBridge printing on the device by selecting the correct USB mode. For more information, see the documentation that came with the device.
1 Disconnect the device. 2 Connect a PictBridge-enabled device to the PictBridge port. See the
documentation that came with your device to determine whether it is PictBridgeenabled. Use only the USB cable that came with the camera. Remove the memory card from the printer.

Error messages

Start errors on page 48 Run errors on page 48

Start errors

The printer was unable to start. This includes the following errors:
1102 to turn the printer off. to turn the printer on.

Run errors

This includes the following errors:

1201 1202

2301 4301. to turn the printer off.
Contact Lexmark Customer Support.

Notices

Electronic emission notices
Federal Communications Commission (FCC) compliance information statement
The LexmarkTM P450, type 4350 has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC Class B limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult your point of purchase or service representative for additional
suggestions. The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment. Any questions regarding this compliance information statement should be directed to: Director of Lexmark Technology & Services Lexmark International, Inc. 740 West New Circle Road Lexington, KY 40550 (859) 2323000
Industry Canada compliance statement
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Avis de conformit aux normes de lindustrie du Canada
Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.
European Community (EC) directives conformity
This product is in conformity with the protection requirements of EC Council directives 89/336/EEC and 73/23/EEC on the approximation and harmonization of the laws of the Member States relating to electromagnetic compatibility and safety of electrical equipment designed for use within certain voltage limits. A declaration of conformity with the requirements of the directives has been signed by the Director of Manufacturing and Technical Support, Lexmark International, Inc., S.A., Boigny, France. This product satisfies the Class B limits of EN 55022 and safety requirements of EN 60950.

Japanese VCCI notice

If this symbol appears on your product, the accompanying statement is applicable.

Korean MIC statement

This equipment has undergone EMC registration as a household product. It can be used in any area, including a residential area.

Noise emission levels

The following measurement was made in accordance with ISO 7779 and reported in conformance with ISO 9296. 1-meter average sound pressure, dBA Printing 44 dBA
Waste from Electrical and Electronic Equipment (WEEE) directive
The WEEE logo signifies specific recycling programs and procedures for electronic products in countries of the European Union. We encourage the recycling of our products. If you have further questions about recycling options, visit the Lexmark Web site at www.lexmark.com for your local sales office phone number.

general troubleshooting 43
Image Enhance feature 23 incorrect language appears on display 44 index page 17 information finding 7 Ink Level feature 36 ink level, checking 36 inserting USB flash drives 29 installing print cartridge 38

jam, paper 46

Device Name 32

language incorrect 44

light CD drive 30 memory card 30 loading paper 15
memory card CompactFlash Type 28 inserting 27 Memory Stick (MS) 28 Memory Stick Duo 28 Memory Stick PRO 28 Mini Secure Digital 28 MultiMedia Card (MMC) 28 Secure Digital (SD) 28 SmartMedia 28 xD Picture Card 28 memory card cannot be inserted 47 memory card is inserted nothing happens 47 memory card slots 9 menus Copy Photos 13 Print All / Index 13 Setup 13 Slide Show 13 View & Print 13 menus, display navigating 13 misfeeds, paper 46 moving print area 21 multiple copies, printing 19
nothing happens when memory card is inserted 47 notices 50, 52

ordering supplies 36

page does not print 44 paper loading 15 sizes 15 paper exit tray 9 paper jam 46
paper misfeeds 46 paper size selecting 16 Paper Size setting 16 paper support 9 Paper Type setting 16 part number cartridge 36 personal digital assistant 32 phone camera 32 photo storage device troubleshooting 47 photos adjusting print area 21 cropping 21 editing 21 previewing 17 printing from PictBridge-enabled camera 34 rotating 21 selecting 17 viewing slide show 26 zooming 21 PictBridge cannot print 48 PictBridge port 9 PictBridge-enabled camera printing photos 34 poor edge quality 46 poor graphic quality 45 poor quality 45 power button 9 power button not lit 43 power connector 11 previewing photos 17 print page does not 44 Print All / Index 13 print area adjusting 21 moving 21 print cartridge aligning 39 cleaning 39 installing 38 removing 37 wiping 40 print quality selecting 19 Print Quality setting 19 printer does not feed paper 46
printing all photos 19 black and white 24 index page 17 multiple copies 19 photos from PictBridge-enabled camera 34 test page 41 using DPOF settings 34 publications finding 7
USB flash drives inserting 29 USB port 11 using CD drive 30
video output 26 video output port 26 View & Print 13

quality poor 45

Web site finding 8
recycling Lexmark products 42 red eye, removing 23 Remove Red-Eye feature 23 removing print cartridge 37 rotating photos 21

zooming photos 21

safety information 5 selecting paper size 16 photos 17 print quality 19 selecting paper types 16 Sepia Tone Print 24 Setup 13 Slide Show 13 slide show, viewing 26 supplies, ordering 36
Test Page feature 41 test page, printing 41 troubleshooting general 43 photo storage device 47 troubleshooting error messages 0000-1200-4301 48

Sometimes your work is stacked up against you.
S o m e t i m e s i t s n o t.

Lexmark E450dn

Compact, easy to use and packed with performance!

Space-friendly duplex

A true rarity for a high-function duplex standard printer, the Lexmark E450dn is surprisingly small, fitting easily on tiny desktops and in tight workstations.

Up to 33 ppm

Simplified operation
The intuitive all-points-addressable display gives end-users crystal-clear information to carry out printing and maintenance tasks with ease.

Easy to use OP Panel

Lower running costs
With the optional high-yield 11,000 page aftermarket cartridges, you can drive down your cost per page and run longer with less intervention.

Compact design

An outstanding value for your small or medium-sized workgroup
Fast, reliable and incredibly easy to use, the Lexmark E450dn mono laser offers you a great range of features and functions at a competitive price. Armed with 64MB of standard memory expandable to 320MB it will zip through your heaviest print runs at up to 33 ppm. And it gives you flexible options, like a second input drawer to reach up to 800 sheets.
Small size, giant savings
Duplex printing is an intelligent solution for any business, saving money as well as the environment. But the Lexmark E450dn goes even further, optimising valuable office space thanks to its remarkably compact design yet with no compromise to performance! Additionally, you can save on printing costs with the optional 11,000 page cartridges.

Life just got simpler

You've got no time for brainteasers. With the effortless new operator panel, the guessing games are over! The intuitive 4-line display coaches you through operational tasks step by step. And you can even benefit from convenient 'show me' and 'tell me more' functions, which provide distinctive graphics and additional, detailed information.
Print Technology Monochrome Laser Print Speed (A4, Black) Up to 33 ppm Print Speed (A4, Black) Duplex Up to 16 spm Print Speed (Letter, Black) Up to 35 ppm Print Speed (Letter, Black) Duplex Up to 16 spm Time to First Page (Black) As fast as 7 seconds Print Resolution, Black 1200 Image Quality 1200 x 1200 dpi 2400 Image Quality 600 x 600 dpi Processor 400 MHz Memory, Standard 64 MB Memory, Maximum 320 MB Expandable Memory Options Yes Apple Macintosh Operating Systems Supported Mac OS X, Mac OS 9.x Citrix MetaFrame Citrix, MetaFrame and MetaFrame XP are registered trademarks or trademarks of Citrix Systems, Inc. in the U.S. and other countries., Microsoft Windows 2000 Server running Terminal Services with Citrix MetaFrame XP Presentation Server or Citrix MetaFrame Presentation Server 3.0., Microsoft Windows Server 2003 running Terminal Server with Citrix MetaFrame XP Presentation Server or Citrix MetaFrame Presentation Server 3.0, Microsoft Windows 2000 Server running Terminal Services with Citrix Presentation Server 4.0, Microsoft Windows Server 2003 running Terminal Server with Citrix Presentation Server 4.0 Linux Operating Systems Supported Red Flag Linux Desktop 4.0, 5.0, Linpus Linux Desktop 9.2, 9.3, Red Hat Enterprise Linux WS 3.0, 4.0, SUSE Linux Enterprise Server 8.0, 9.0, SUSE Linux Professional 9.1, 9.2, 9.3, Debian GNU/Linux 3.0, 3.1, Linspire Linux 4.5, 5.0, SUSE Linux 10.0, 10.1 Microsoft Windows Operating Systems Supported 2000, NT (4.00/4.00 Server), Me, XP, Server 2003, 98 2nd Edition, XP x64, Server 2003 running Terminal Server, 2000 Server running Terminal Services, Server 2003 x64 Edition, Vista Novell Operating Systems Supported NetWare 5.x, 6.x with iPrint or Novell Distributed Print Services (NDPS)

UNIX Operating Systems Supported Sun Solaris SPARC 7, 8, 9, 10, HP-UX 11.00, 11.11, IBM AIX 5.1, 5.2, 5.3, Sun Solaris xOther Operating Systems Supported IBM iSeries or IBM AS/400 Systems with TCP/IP with OS/400 V3R1 or later using OS/400 Host Print Transform, Virtually any platform supporting TCP/IP
Paper Handling Standard 150-Sheet Output Bin, Integrated Duplex, Single Sheet Exit, Single Sheet Manual Feed Slot, 250-Sheet Input Tray Paper Handling Optional 550-Sheet Drawer Paper Input Capacity (Standard) 250 pages 20 lb or 75 gsm bond Paper Input Capacity (Maximum) 800 pages 20 lb or 75 gsm bond Paper Output Capacity (Standard) 150 pages 20 lb or 75 gsm bond Paper Output Capacity (Maximum) 150 pages 20 lb or 75 gsm bond Envelope Capacity 1 Finishing Option No Number of Paper Inputs 2 Number of Paper Inputs, Maximum 3 Media Types Supported Card Stock, Envelopes, Paper Labels, Plain Paper, Transparencies, Refer to the Card Stock & Label Guide Media Sizes Supported 10 Envelope, 7 3/4 Envelope, 9 Envelope, A4, A5, B5 Envelope, C5 Envelope, DL Envelope, A6 Card, Executive, Folio, JIS-B5, Legal, Letter, Statement, Universal
Network Protocol Support TCP/IP IPv4, AppleTalk, TCP/IP IPv6 Printable Area 4 mm of the top, bottom, right and left edges (within) Printer Languages (Standard) PCL 5e Emulation, PCL 6 Emulation, PPDS, PostScript 3 Emulation, PDF 1.5 Emulation Packaged Size (mm - H x W x D) 378 x 470 x 430 mm Size (mm - H x W x D) 259.5 x 359 x 396 mm Weight (kg) 11.4 kg Acoustics/Noise level (Idle mode) inaudible dBA Acoustics/Noise level (Operating mode) 52 dBA Product Guarantee One year return to base, 5-7 business days response time Product Certifications FCC Class B, UL 60950-1 3rd Edition, U.S. FDA, IEC 320-1, CSA, ICES Class B, Energy Star, CE Class B, CB IEC 60950-1, IEC 60825-1, GS (TV), SEMKO, UL AR, CS, TV Rh, N Mark, ACA C-tick Class B, CCC Class B, BSMI Class B, MIC, EK Mark, PSB Duty Cycle Up to 80,000 Pages per month (one-time monthly usage) Specified Operating Environment Temperature: 16 to 32C (60 to 90F), Altitude: 0 - 2500 Meters (8,200 Feet), Humidity: 8 to 80% Relative Humidity for Temperatures less than 25.5C (78F)
Connectivity (standard) Centronics IEEE 1284 Bidirectional Parallel, Fast Ethernet, USB 2.0 Specification Hi-Speed Certified Connectivity (optional) Lexmark N4000e Fast Ethernet (Print Only), Lexmark N4050e 802.11g Wireless Print Server (Print Only), External MarkNet N7020e Gigabit Ethernet, External MarkNet N7000e Fast Ethernet (USB), External MarkNet N7002e Fast Ethernet (parallel) Network Printing Methods LPR/LPD, Direct IP (Port 9100), IPP (Internet Printing Protocol), HTTP, Enhanced IP (Port 9400), FTP, TFTP
Cartridges Ships with 6K* Return Programme Toner Cartridge Aftermarket cartridges available : 6K* and 11K* Return Programme Toner Cartridge. Regular Cartridges also available. 30K pages Photoconductor

* Average cartridge yield. Declared Yield value in accordance with ISO/IEC 19752.
Cost saving & environmental features The Energy Star compliance and the instant warm-up fuser technology contributes to reduce energy consumption - Integrated duplex printing, print and hold (verify print), multi-up printing and quality printing on recycled paper help reduce paper consumption - Return Programme cartridges and end-of-life product management help reduce landfill.
Models available E450dn Duplex, Network
Specifications are subject to change without notice. Lexmark, Lexmark with diamond design is trademark of Lexmark International, Inc. registered in the United States and or other countries. All other trademarks are the properties of their respective owners.
w w w. l e x m a r k. c o m
Copywriter: Bill Fahber / Visual: Getty Images
Lexmark believes that the environment is a critical component of responsible business management and clearly demonstrates it by implementing the 4R strategy: Reduce, Recover, Reuse and Recycle. To learn more about these programmes please visit www.lexmark.com/recycle
With our innovative solutions and services, we help you PRINT smarter, MOVE information faster and MANAGE output more efficiently across your enterprise. Ask your local Lexmark representative for more information.