Remote Control Sensor

OK POWER MENU VOLUME

PROGRAMME

LCD TV Models
26/32/37/42LC4R* 26/32/37/42LC7R*

VOLUME

OK MENU

OK MENU INPUT POWER

Power/Standby Indicator illuminates red in standby mode. illuminates green when the TV is switched on.

32/42LB9R*

PR VOL OK MENU INPUT
Intelligent Eye Adjusts picture according to the surrounding conditions.

BACK PANEL INFORMATION

This is a simplified representation of the back panel. Image shown may differ from your TV.
HDMI/DVI IN 1 HDMI IN 2 RGB IN

AV IN 1

R AUDIO L/MONO VIDEO

AV OUT

S-VIDEO

AV IN 3

1 VARIABLE AUDIO OUT 2
VIDEO L/MONO AUDIO R S-VIDEO
MONO VIDEO L/MONO AUDIO R

COMPONENT IN

S-Video Input Connect S-Video out from an S-VIDEO device. Audio/Video Input Connect audio/video output from an external device to these jacks. AV IN 2

HDMI/DVI IN 1

HDMI IN 2

RGB IN

RGB AV (PC)

AV IN 1 V

L/MONO R AUDIO L/ MONO VIDEO

AUDIO AV 2 (RGB/DVI)

AV OUT V

ANTENNA IN

HDMI/DVI IN

HDMI IN

(CONTROL & SERVICE)

COMPONENT IN 2

COMPONENT IN VIDEO
2 COMPONENT IN VARIABLE AUDIO OUT 3
VARIABLE AUDIO OUT ARIABLE

VARIABLE AUDIO OUT

RS-232C IN

L/MONO

AV V AV IN 2 OUT AV IN 2

VIDEO L/MONO AUDIO R

L/MONO VIDEO L/ MONO AUDIO R

RGB IN COMPONENT IN

2 COMPONENT IN VARIABLE AUDIO OUT

COMPONENT IN 1

HDMI/DVI IN 1 2

HDMI IN VIDEO 2

RGB IN AUDIO
VARIABLE AUDIO OUT1 ARIABLE AV IN

L/MONO VIDEO

HDMI/DVI IN 1 HDMI IN RGB IN
R AUDIO L/MONO VIDEO AUDIO R

RGB (PC)

AUDIO (RGB/DVI)

VARIABLE AUDIO OUT 2

AV IN 2 V
S-Video Input Connect S-Video out from an S-VIDEO device. Audio/Video Input Connect audio/video output from an external device to these jacks.
HDMI/DVI IN HDMI/DVI IN 1

HDMI IN HDMI 2

AV IN RGB IN 1

AV OUTAV V

AV IN 2

2 COMPONENT IN

RGB(PC)
Audio/Video Input Connect audio/video output from an external device to these jacks.
S-Video Input Connect S-Video out from an AV IN 1 AV OUT S-VIDEO device.

VIDEO AUDIO

VARIABLE ARIABLE AUDIO OUT
HDMI Input 2 Connect a HDMI signal to HDMI IN. VARIABLE Or DVI(VIDEO)signal to HDMI/DVI port with DVI AUDIO OUT COMPONENT IN to HDMI cable.

VARIABLE AUDIO 1OUT

VARIABLE 1 AUDIO OUT

L/MONO L/ MONO

Audio/Video Input (AV IN 1) Connect audio/video output from an external device to these jacks. AV Output Connect second TV or monitor to the AV OUT socket on the TV. Antenna Input Connect RF antenna (UHF) to this jack. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
RGB/Audio Input Connect the monitor output from a PC to the appropriate input port. Component Input Connect a component video/audio device to these jacks.
Variable Audio Output Connect an external amplifier or add a subwoofer to your surround sound system.
RS-232C Input (CONTROL&SERVICE) Port Connect the serial port of the control devices to VARIABLE the RS-232C jack. AUDIO OUT (This feature is not available for all models.)
STAND INSTALLATION (Only 26, 32,37 inch LCD TV models)
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.
ATTACHING THE TV TO A DESK (Only 32LB9R* model)
If you wish to attach the TV to a desk, it must be securely fastened to the desk using a metal screw (as shown below). Failure to securely attach the TV may result in the TV falling; which may cause damage to the TV and serious personal injury.

Stand 1-Screw

ATTACHING THE TV TO A WALL (This feature is not available for all models.)
Position the TV close to the wall to avoid the possibility of it falling when pushed. The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with bolts (must purchase seperately) to the wall. Ensure that both brackets are even.
Use a strong cord (must purchase separately) to secure the TV. Secure the cord in such a way that it becomes taught when the TV is in position.

! NOTE

When moving the TV undo the cords first. Use a platform or cabinet string and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

AUDIO L/MONO VIDEO AUDIO L/MONO VIDEO

Wall Antenna Socket

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

RGB IN HDMI/DVI IN

UHF HDMI/DVI IN

Antenna

HDMI/DVI IN 1 1
HDMI IN HDMI IN 2 Signal 2

RGB IN RGB IN

AV IN 1 AV OUT AV IN 1 AV OUT
To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the LCD TV models.

HD RECEIVER SETUP

Connecting with a component cable
Connect the video outputs (Y, PB, PR) of the digital TV top box to the C O M P O N E N T I N V I D E O jacks on the TV.
Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O jacks on the TV.
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.)

HDMI DVI IN

Select Component1 input source using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2, select Component2 input source.
Signal 480i/576i 480p/576p 720p/1080i 1080p

Component Yes Yes Yes No

HDMI1/2 No Yes Yes Yes
HDMI/DVI IN HDMI DVI IN 1 HDMI IN HDMI IN 2

(except VGA Models)

Connecting a set-top box with an HDMI cable
Connect the HDMI output of the digital set-top box to the H D M I / D V I I N 1 or H D M I I N 2 jack on the TV.
Select HDMI1 or HDMI2 input source using the I N P U T button on the remote control.
TV can receive the video and audio signal simultaneously with using a HDMI cable. G If the digital set-top box supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1280x720p. G If the digital set-top box player does not support Auto HDMI, you need to TV the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Connecting with a HDMI to DVI cable
HDMI/DVI IN HDMI DVI IN 1

RGB(PC) RGB(PC)

AV IN 1 AV OUT
Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 jack on the TV.
Connect the audio output of the digital set-top box to the A U D I O ( R G B / D V I ) jack on the TV.
Select HDMI1 input source using the I N P U T button on the remote control.

DVD SETUP

Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the TV.
Connect the audio outputs of the DVD to the C O M P ON E N T I N A U D I O jacks on the TV.

Turn on the DVD player, insert a DVD.
Refer to the DVD player's manual for operating instructions.

Component Input ports

To achieve better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV

Y PB PR

PB B-Y Cb Pb

PR R-Y Cr Pr

HDMI IN HDMI IN 2
Video output ports on DVD player
Connecting with a RCA cable
V Connect the A U D I O/V I D E O jacks between TV and DVD player. Match the jack colours (Video = yellow, Audio Left = white, and Audio Right = red)

ANT IN

Insert a DVD into the DVD player and press PLAY on the DVD player. (Refer to the DVD player owners manual.)

OUTPUT SWITCH

ANT OUT
Select AV1 input source using the I N P U T button on the remote control. HDMI DVI IN HDMI IN If connected to A V I N 2, select AV2 input source.

AV IN 1 AV IN 1 AV OUT

Connecting with a S-Video cable

VIDEO S-VIDEO

R AUDIO
Connect the S-VIDEO output of the DVD to the S V I D E O input on the TV.

OUTPUT SWITCH ANT OUT

Connect the audio outputs of the DVD to the A U D I O input jacks on the TV. Turn on the DVD player, insert a DVD. Select AV2 input source using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions.

L/MONO L/MONO

ENT IN

HDMI IN HDMI IN

Connecting the HDMI cable
Connect the HDMI output of the DVD to the H D M I / D V I I N 1 or H D M I I N 2 jack on the TV.
The TV can receive video and audio signals simultaneously when using a HDMI cable. G If the DVD player supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1280x720p. G If the DVD player does not support Auto HDMI, you must TV the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
Supported Display Resolution (HDMI-DTV mode) Resolution 720x480 720x576 Horizontal Frequency(kHz) 31.47 31.50 31.25 44.96 45.00 37.50 33.72 33.75 28.125 67.432 67.5 56.25 Vertical Frequency(Hz) 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 59.50

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable

HDMI DVI IN HDMI IN

RGB OUTPUT
Connect the RGB output of the PC to the R G B ( P C) jack on the TV.
Connect the PC audio output to the A U D I O jack on the TV.
Turn on the PC and the TV.
Select RGB PC input source using the I N P U T button on the remote control.
To enjoy vivid picture and sound, connect the PC to the TV. G Avoid keeping a fixed image on the TV s screen for prolonged periods of time.The fixed image may become permanently imprinted on the screen;use a screen saver when possible. Connect the PC to the RGB (PC) port of the TV; G change the resolution output of PC accordingly. There may be interference relating to resolution, G vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. G The synchronization input waveform for
Horizontal and Vertical frequencies are separate. G We recommend using 1366x768, 60Hz (LCD TV models) / 852x480, 60Hz (42 inch WVGA PLASMA TV models) / 1024x768, 60Hz (42 inch XGA PLASMA TV models) / 1360x768, 60Hz (50 inch PLASMA TV models) for the PC mode, these should provide the best picture quality. G If the resolution of PC is over SXGA, there will be no picture on the TV. G Connect the audio cable from the PC to the Audio input on the TV.(Audio cables are not included with the TV). G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of the cable. This provides the best picture quality.
Supported Display Resolution (RGB-PC mode) Resolution 640x350 720x400 640x480 848x480 852x480 800x600 1024x768 1280x768 1360x768 1366x768 Horizontal Frequency(kHz) 31.5 31.5 31.5 31.5 31.5 37.9 48.4 47.8 47.7 47.7 Vertical Frequency(Hz) 70.1 70.1 59.9 60.0 60.0 60.3 60.0 59.9 59.8 59.8
Its supported to 848x480, 852x480 in VGA modes. (VGA Models) Its supported to 1280x768, 1360x768, 1366x768 in XGA modes. (XGA Models)

Screen Setup for PC mode

Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment.

REVEAL

INPUT TV INPUT

MODE TV DVD

MODE Selects the remote operating modes.
TELETEXT These buttons are used for teletext. BUTTONS For further details, see the Teletext section.

RATIO SIMPLINK

TEXT I/II
PIP INPUT PIP PR- PIP PR+
SIMPLINK See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen.(G p. 4 4) I/II Selects the sound output. Coloured These buttons are used for teletext (on T E L E T E X T modbuttons els) or P r o g r a m m e e d i t. THUMBSTICK Allows you to navigate the on-screen menus and adjust (Up/Down/Left the system settings to your preference.

Right)

OK Accepts your selection or displays the current mode.
VOLUME Adjusts the volume. UP/DOWN
FAV Displays the selected favourite programme. MUTE Switches the sound on or off.
Programme Selects a programme. UP/DOWN 0~9 number Selects a programme. buttons Selects numbered items in a menu.

Installing Batteries

Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -). Install two 1.5V AA batteries. Do not mix old or used batteries with new ones. Close cover.

TURNING ON THE TV

When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. In standby mode to turn TV on, press the , I N P U T, P R D / E button on the TV or press the P O W E R, T V, I N P U T, P R + / -, N U M B E R( 0~9 ) buttons on the remote control and the TV will switch 9 on.

PROGRAMME SELECTION

Press the P R + / - or N U M B E R buttons to select a programme number.

VOLUME ADJUSTMENT

Press the V O L + / - button to adjust the volume. If you wish to switch the sound off, press the M U T E button. You can cancel the Mute function by pressing the M U T E, V O L + / - o r I / I I button.
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. The OSD mainly use pictures for the Plasma TV models.
Press the M E N U button and then D / E button to display each menu. Press the G button and then D / E button to select a menu item. Change the setting of an item in the sub or pull-down menu with F / G button. You can move to a higher level menu by pressing the O K or M E N U button.

Press the G button to begin auto tuning. All receivable stations are stored. To stop auto tuning, press the M E N U button. When auto tuning is complete, the Programme edit menu appears on the screen. See the Programme edit section to edit the stored programme.

Auto Tuning C BG 35%

MANUAL PROGRAMME TUNING
Manual programme lets you manually tune and arrange the stations in whatever order you desire.
EXIT LIST MENU Q.VIEW SLEEP
Press the M E N U button and then D / Setup menu. Press the G button and then D / Tuning. Press the

button to select the

button to select Manual button to select Storage.

button and then D /

Press the / G button or NUMBER buttons to select the desired programme number (0 to 99). If you use NUMBER buttons, any number under 10 is entered with a numeric 0 in 0 front of it, i.e. for 5. Press the D /

button to select System.

Press the D / E button to select a TV system menu; BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / NewZealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS) M : (USA / Korea / Philippines) Press the D /
Setup Auto Tuning Manual Tuning Manual Tuning Programme Edit Favourite Programme To Set

button to select Band.

Press the G button and then D / or Cable. Press the D /

button to select V/UHF

button to select Channel.
Manual Tuning Storage System Band Channel Fine Search Name
You can select the desired programme number with the F / G button or NUMBER buttons. If possible, select the programme number directly with the number buttons. Any number under is entered with a numeric 0 in front of it, i.e. for 5. Press the D /

button to select Search.

Press the F / G button to commence searching. If a station is found the search will stop. Press the O K button to store it. To store another station, repeat steps 3 to 1 3. Press the E X I T button to return to normal TV viewing.

FINE TUNING

Normally fine tuning is only necessary if reception is poor.
Press the M E N U button and then D / the Setup menu.
Press the G button and then D / Manual Tuning.
Press the G button and then D /

button to select Fine.

Auto Tuning Manual Tuning Programme Edit Favourite Programme
Press the G button and then F / the best picture and sound.

button to fine tune for

Setup Auto Tuning Manual Tuning Manual Tuning Programme Edit Favourite Programme
Press the O K button to store it.

ASSIGNING A STATION NAME

You can assign a station name up to five characters to each programme number.
Press the G button and then D / Name.
Press the G button and then D / E button. You can use a blank, + , - , the number 0 to 9 and the alphabet A to Z.
Press the / G button to select the position and make your choice of the second character, and so on.
Auto Tuning Manual Tuning Manual Tuning Programme Edit Favourite Programme

PROGRAMME EDIT

This function enables you to delete or skip stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number.
Press the M E N U button and then D / the Setup menu. Press the G button and then D / Programme Edit.
Press the G button to display the Programme edit menu.
Deleting a programme 1.Select a programme to be deleted with the D / E / F / button. 2.Press the RED button twice. The selected programme is deleted, all the following programmes are shifted up one position.
Copying a programme 1.Select a programme to be copied with the D / E / F / G button. 2.Press the GREEN button. All the following programmes are shifted down one position.
Setup Auto Tuning Manual Tuning Programme Edit Programme Edit Favourite Programme
Moving a programme 1.Select a programme to be moved with the D / E / F / G button. 2.Press the YELLOW button. 3.Move the programme to the desired programme number with the D / E / F / G button. 4.Press the YELLOW button again to release this function. Skipping a programme number 1.Select a programme number to be skipped with the D / E / F / G button. 2.Press the BLUE button. The skipped programme turns to blue. 3.Press the BLUE button again to release the skipped programme. When a programme number is skipped it means that you will be unable to select it using the D / E button during normal TV viewing. If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu.
Programme Edit 0 C BLN C S S 67 Delete Move 9 S S S C C 11

Language SIMPLINK Key Lock ISM Method Low Power
Press the G button and then D / Off.

button to select On or

Off On
In K e y L o c k O n, if the TV is turned off, press the r / I, I N P U T, P R D / E button on the TV or P O W E R, I N P U T, T V, P R + / - or NUMBER buttons on the remote control. With the K e y L o c k O n, the display Key Lock On appears on the screen if any button on the front panel is pressed while viewing the TV.
This fundtion operates only with devices with the SIMPLINK logo. Please check the SIMPLINK logo. This allows you to control and play other AV devices connected to the display through HDMI cable without additional cables and settings. If you do not require the SIMPLINK menu, select Off.
Press the M E N U button and then D / Option menu.
Press the G button and then D / E button to select SIMPLINK.
Option Language SIMPLINK Key Lock ISM Method Low Power Off On

SIMPLINK Functions

Disc playback Control connected AV devices by pressing the D / E / F / G, O K buttons and buttons for play, stop, pause, fast reverse, fast forward, chapter skip.(The button does not provide such functions) Direct Play After connecting AV devices to the TV, you can directly control the devices and play media without additional settings. Select AV device Enables you to select one of the AV devices connected to the TV and operate it. Power off all devices When you switch off the TV, all connected devices are turned off. Switch audio-out Offers an easy way to switch audio-out. * A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide this function.

SIMPLINK Menu

Press the D / E /
/ G button and then OK button to select the desired SIMPLINK source.
T V v i e w i n g : Switch to the previous TV programme regardless of the current mode.
D I S C p l a y b a c k : Select and play discs. When multiple discs are available, the titles of the discs are conveniently displayed at the bottom of the screen. V C R p l a y b a c k : Control the connected VCR. H D D R e c o r d i n g s p l a y b a c k : Control recordings stored in HDD. Audio Out to Home theater/Audio Out to TV : Select Home theater or TV speaker for Audio Out.
DISC DVD HTS VCR HDD Recorder

Selected Device

When no device is connected (displayed in gray) When a device is connected (displayed in bright colour)

SPEAKER F TV Speaker

Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the SIMPLINK device with the HDMI cable. G After connecting the HDMI terminal for the home theatre with SIMPLINK function using the above method, connect the VARIABLE AUDIO OUT terminal on the back of the TV to the VARIABLE AUDIO IN terminal on the back of the SIMPLINK device with the VARIABLE AUDIO OUT cable. G When operating an external device with SIMPLINK, press the TV button from the MODE button on the remote control. G When you switch the Input source using the INPUT button on the remote control, you can stop the operation of a device controlled by SIMPLINK. G When you select or operate a media device with home theatre function, the speaker automatically switches to home theatre speaker (HT speaker).

PICTURE CONTROL

WATCHING PIP(PICTURE-IN-PICTURE)
PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image. PIP function is available in the Component, RGB, HDMI mode. (But, it cant adjust 480i/576i resolution of Component mode.)
INPUT TV INPUT POWER MODE TV DVD RATIO SIMPLINK VCR
Watching PIP/Double Window
Press the P I P button to access the sub picture. Each press of PIP changes the PIP options.

PIP Mode

DW Mode

PIP Off

Programme Selection for Sub Picture
Press the PIP PR +/- button to select a programme for the sub picture. The selected programme number is displayed just below the programme number of main picture.
Input Source Selection for Sub Picture
Press the P I P I N P U T button to select the input source for the sub picture. Each press of P I P I N P U T button is pressed, each input source for the sub picture is displayed. (Sub picture can be selected only TV, AV1, AV2)
Sub Picture Size Adjustment (PIP mode only)
Press the S I Z E button to adjust the sub picture size. With S I Z E button in PIP mode, sub picture is adjusted.
Moving the Sub Picture (PIP mode only)
Press the P O S I T I O N button. Repeatedly press the P O S I T I O N button then sub picture moves.
PICTURE SIZE (ASPECT RATIO)CONTROL
You can watch the screen in various picture formats; S p e c t a c l e, O r i g i n a l, 4 : 3, : 9, : 9 and Z o o m 1 / 2. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. You can adjust the enlarge proportion using D / This function works in the following signal.

button.

Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the Picture menu.

Advanced Cinema Black Level

Low High

PICTURE RESET
Returns to the default factory setting for Picture Mode, Colour Temperature, XD, Advanced, Aspect Ratio.
Press the G button and then D / Picture Reset.
Press the G button to initialize the adjusted value.
IMAGE STICKING MINIMIZATION(ISM)METHOD
A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the screen for prolonged periods.
It is not possible to use this function in LCD models.
White Wash White wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes. Inversion This function inverts the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
Press the M E N U button and then D / select the Option menu.
Language SIMPLINK Key Lock ISM Method ISM Method Low Power
Normal White Wash Orbiter Inversion
Press the G button and then D / ISM Method.
Press the G button and then D / E button to select either Normal, White Wash, Orbiter or Inversion. If you do not need this function, set Normal.

LOW-POWER PICTURE MODE

This function allows you to reduce the power consumption of the TV.
Press the M E N U button and then D / select the Option menu. Press the G button and then D / Low Power.
Press the G button and then D / E button to select On or Off. Press the E X I T button to return to normal TV viewing.
SOUND & LANGUAGE CONTROL

AUTO VOLUME LEVELER

Auto Volume automatically remains on the same level of volume if you change programmes.
Press the M E N U button and then D / the Audio menu.
Press the G button and then D / Volume.

button to select Auto

Sound Mode Auto Volume Balance TV Speaker
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; Surround MAX, Standard, Music, Movie or Sports and you can also adjust the frequency of the equalizer.

Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content.
S u r r o u n d M A X, S t a n d a r d, M u s i c, M o v i e, and S p o r t s are preset for optimum sound quality at the factory and are not adjustable. S u r r o u n d M A X Select this option for the most realistic sound. Standard Commanding and natural audio. Music Select this option to enjoy the original sound when listening to music. Movie Select this option to enjoy sublime sound. Sports Select this option to watch sports broadcasting. User Select this option for user-defined audio settings.
Surround MAX Standard Music Movie Sports User
Press the G button and then D / E button to select Sound Mode.
Press the G button and then D / E button to select Surround MAX, Standard, Music, Movie, Sports or User.
SOUND SETTING ADJUSTMENT -USER MODE
Adjusting the audio equalizer.
Press the G button and then D / Sound Mode.
Select a frequency band by pressing the F / G button. Set the desired sound level with the D / E button.

0.1 0.5 1.5 5.kHz

BALANCE
You can adjust the sound balance of the speakers to the preferred levels.
Press the G button and then D / Balance.
Press the G button and then F / desired adjustment.

button to make

TV SPEAKERS ON/OFF SETUP
You can adjust the internal speaker status. In AV, COMPONENT, RGB[PC] and HDMI mode, internal speaker audio can be operational even when there is no video signal. If you wish to use an external hi-fi system, turn off the TV internal speakers.

Speaker.

button to select TV
Press the G button and then D / On or Off.

Stereo/Dual Reception

When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
Broadcast Mono Stereo Dual

On Screen Display

MONO STEREO DUAL I
Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono by pressing the I / I I button twice. In mono reception, the clarity of sound is improved. To switch back to stereo, press the I / I I button twice. Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I / I I button repeatedly.

DUAL I DUAL II DUAL I+II

Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker.

SIMPLE TEXT

Page selection
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The PR+/- button can be used to select the preceding or following page.

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the P R + button can be used. The red button return to the previous selection. Alternatively the PR- button can be used.

Direct page selection

As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.

FASTEXT

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.
Press the i button to select the index page. You can select the pages which are colour coded along the bottom line with corresponding coloured buttons. As with SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The P R + / - button can be used to select the preceding or following page.
SPECIAL TELETEXT FUNCTIONS

A REVEAL

Press this button to display concealed information, such as solutions to riddles or puzzles. Press this button again to remove the information from the display.

A SIZE

Selects double height text. Press this button to enlarge the top half of the page. Press this button again to enlarge the bottom half of the page. Press this button again to return to the normal display.

A UPDATE

Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Press this button again to view the updated teletext page.