PCMCIA CARD SLOT

LCD TV Models: 19/22/26/32/37/42LG30** 32/37/42/47/52LG50**

HDMI IN 3

PCMCIS CARD SLOT
DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.

COMPONENT IN

USB IN SERVICE ONLY
AUDIO IN OPTICAL DIGITAL (RGB/DVI) AUDIO OUT

HDMI/DVI IN 2

RGB IN (PC)
1(DVI) RS-232C IN (CONTROL & SERVICE)

ANTENNA IN

Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. RGB/DVI Audio Input Connect the audio from a PC or DTV.
Component Input Connect a component video/audio device to these jacks. Antenna Input Connect RF antenna to this jack. PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) Audio/Video Input Connect audio/video output from an external device to these jacks. S-Video Input Connect S-Video out from an S-VIDEO device. Headphone Socket Connect the headphone plug to this socket. SERVICE ONLY PORT
HDMI Input Connect a HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable.
RGB Input Connect the output from a PC. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.

AUDIO IN (RGB/DVI)

RS-232C IN (CONTROL & SERVICE)

RGB (PC) IN

COMPONENT IN VIDEO AUDIO
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable. RGB/DVI Audio Input Connect the audio from a PC or DTV. Antenna Input Connect RF antenna to this jack. PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.)
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. Component Input Connect a component video/audio device to these jacks. RGB Input Connect the output from a PC. SERVICE ONLY PORT

STAND INSTALLATION

(LCD TV Models: 26/32/37/42LG30**, 32/37/42LG50**)
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.

Assemble the TV as shown.
Assemble the parts of the S t a n d B o d y with the C o v e r B a s e of the TV.
Fix the 4 bolts securely using the holes in the back of the TV.

Stand Body

Cover Base

(Only 19/22LG30**)

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the TV. Insert the S T A N D B O D Y into a C O V E R B A S E until clicking sound. Assemble the TV as shown.
(Only 42PG10**, 42PG20**, 42PG30**)
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the TV as shown. Fix the 4 bolts securely using the holes in the back of the TV.
STAND INSTALLATION (Only 19/22LS4D*)
Image shown may differ from your TV. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Insert the S t a n d B o d y into the TV until clicking sound.
Hold the H i n g e B o d y and bend it upward.

Hinge Body

Swivel Stand
(Except for 19/22LS4D*, 50PG10**)
After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your viewing position.
DETACHING STAND (Only 19/22LS4D*)
Image shown may differ from your TV. Place the tv with its front facing downward on a cushion or soft cloth.
Hold the S t a n d B o d y and bend it upward.
Pull the C o v e r B a s e backward during pressing a button on the S t a n d B o d y.
Pull stand body to separate from the TV during pressing 2 latches.
Hold the C o v e r B a s e and pull with shake it backward to separate from the S t a n d B o d y.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
You should purchase necessary components to fix the TV to the wall on the market. Position the TV close to the wall to avoid the possibility of it falling when pushed. The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen these bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

G Connect

the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV). G If using a sound card, adjust PC sound as required. G This TV uses a VESA Plug and Play Solution. The TV provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when using this TV. G DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode. G If required, adjust the settings for Plug and Play functionality. G If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV. G If the graphic card on the PC does output analogue and digital RGB simultaneously, switch the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.) G DOS mode may not work depending on the video card if you use a HDMI to DVI cable. G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality.
Supported Display Resolution (Only 19/22LS4D*)

RGB[PC], HDMI[PC] mode

Resolution 720x400 640x480 800x600 832x624 1024x768 1280x768 1360x768 1366x768 1280x1024 1440x900 1400x1050 1680x1050 Horizontal Frequency(kHz) 31.468 31.469 37.684 37.879 46.875 49.725 48.363 56.470 60.123 47.78 47.72 47.56 63.595 55.5 64.744 65.16 Vertical Frequency(Hz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.029 59.87 59.8 59.6 60.0 59.90 59.948 59.94

HDMI[DTV] mode

Resolution 720x480 720x576 1280x720 Horizontal Frequency(kHz) 31.469 31.5 31.25 37.500 44.33.72 33.75 28.125 26.33.716 33.75 56.250 67.43 67.5 Vertical Frequency(Hz) 59.59.59.50.00 23.29.976 30.59.94 60

1920x1080

Only 19LS4D* Only 22LS4D*
Supported Display Resolution
(Only 19/22/26/32/37/42LG30**, 32/37/42/47/52LG50**)
Resolution 720x400 640x480 800x600 832x624 1024x768 1280x768 1360x768 1366x768 1440x900 1400x1050 1680x1050 1280x1024 1920x1080 Horizontal Frequency(kHz) 31.468 31.469 37.684 37.879 46.875 49.725 48.363 56.470 60.123 47.78 47.72 47.56 55.5 64.744 65.16 63.595 66.647 Vertical Frequency(Hz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.029 59.87 59.8 59.6 59.90 59.948 59.94 60.0 59.988

Resolution 720x480 720x576 1280x720 Horizontal Frequency(kHz) Vertical Frequency(Hz)
31.469 / 31.5 59.94 / 60 31.37.44.96 / 45 59.94 / 60 33.72 / 33.75 59.94 / 60 28.125 50.00 26.97 / 27 23.97 / 24 33.716 / 33.75 26.976 / 30.00 56.67 / 67.43.5 59.94 / 60
Only 19LG30** Only 22LG30** Only 19LG30**, 37/42/47/52LG50** Only 37/42/47/52LG50**
Supported Display Resolution (Only 42/50PG10**, 42/50PG20**, 42/50/60PG30**)
Resolution 720x400 640x480 800x600 1024x768 1280x768 1360x768 1920x1080 Horizontal Frequency(kHz) 31.468 31.469 37.879 48.363 47.78 47.72 66.647 Vertical Frequency(Hz) 70.08 59.94 60.31 60.00 59.87 59.80 59.988
Resolution 640x480 720x480 720x576 1280x720 Horizontal Frequency(kHz) 31.469 31.469 31.47 31.50 31.25 37.50 44.96 45.00 28.125 33.72 33.75 27.000 33.75 56.25 67.433 67.50 Vertical Frequency(Hz) 59.94 60.00 59.94 60.00 50.00 50.00 59.94 60.00 50.00 59.94 60.00 24.50.00 59.94 60

Screen Setup for PC mode

Screen Reset
Returns to the default settings Position, Size and Phase at the factory. This function works in the following mode : RGB[PC].

PICTURE

SCREEN
Resolution Auto Config. Position Size Phase Reset

RETURN Prev.

Contrast : 70 Brightness : 50 Sharpness : 50 Colour : 50 Tint :0 Advanced Control Picture Reset Screen

To Set

1MENU 2

Select PICTURE.

Select SCREEN.

Select Reset.

Select Yes.

Run Reset.

Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Adjustment for screen Position, Size, Phase
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This function works in the following mode : RGB[PC].

Resolution Auto Config.

Position Size Phase Reset
Select Position, Size or Phase.
Make appropriate adjustments.

Selecting Resolution

To view a normal picture, match the resolution of RGB mode and selection of PC mode. This function works in the following mode: RGB[PC] mode.

1024 x x x x 768

Except for PLASMA TV

Select Resolution.

Select the desired resolution.
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. Auto configure This function is for automatic adjustment of the screen position, clock, and phase The displayed image will be unstable for a few seconds while the auto configuration is in progress.

Turn the skipped programme number to blue.
that you will be unable to select it using the P (or PR + / -) button during normal TV viewing.
If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
Release the skipped programme.
Selecting favourite programme
Select your favourite programme number.
It will automatically include the selected
programme into your favourite programme list.

IN TV MODE

This function enables you to delete or skip the stored programmes. You can also move some channels to other programme numbers.

Auto Sort

Start Auto Sort.
After activating Auto Sort once, you can no longer edit programmes.

Deleting a programme

Select a programme number to be deleted.
The selected programme is deleted, all the fol-
lowing programmes are shifted up one
Turn the deleted programme number to red.
Release the deleted programme.

Moving a programme

Select a programme number to be moved.

YELLOW

Turn the moved programme number to YELLOW.
Release the moved programme.
Selecting a Favourite Programme
The selected programme will be added to the
favourite programme list.
BOOSTER (IN DIGITAL MODE ONLY)
If reception is poor, selectBooster to On. When the signal is strong, select Off.
Auto tuning Manual tuning Programme Edit Booster :: On Booster On Software Update : Off Diagnostics CI Information

Off On On

Select Booster.

Select On or Off.

SOFTWARE UPDATE
Software Update means software can be downloaded through the digital terrestrial broadcasting system.
Auto tuning Manual tuning Programme Edit Booster : On Software Update :: Off Software Update Off Diagnostics CI Information

Off Off On

Select Software Update.
Select On or Off. If you select On, a user confirm message box will be displayed to notify that new software is found. Save.
* When setting Software Update
Occasionally, a transmission of updated digital software information will result in the following menu on the TV screen. Select the Y E S using the button and you will see the following picture. After the Software Update is complete, the System restarts.
When the Software Update O menu is "O f f", the message to O change it to "O n" appears.

When the power is turned off, downloading starts. When the power is turned on while updating, the progress status is displayed.
- During Progress of a Software Update, please note the following: Power to the TV must not be interrupted. The TV must not be switched off. The antenna must not be disconnected. After Software Update, you can confirm the updated software version in Diagnostics menu.
DIAGNOSTICS (IN DIGITAL MODE ONLY)
This function enables you to view information on the Manufacturer, Model/Type, Serial Number and Software Version. This displays the information and signal strength of the tuned MUX. This displays the signal information and service name of the selected MUX.

Engineering Diagnostics

Manufacturer Model/Type Serial No. Software Version CH 30 CH 34 CH 36 CH 38 CH 54 CH 60
Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics Diagnostics CI Information
: LG Electronics Inc. : 22LS4D : 708KGKG00019 : V1.18.1

MENU Exit

Select Diagnostics.
Display Manufacturer, Model/Type, Serial Number and Software Version.
Display the information of Channel.
CI [COMMON INTERFACE] INFORMATION
This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services. When the module is inserted into the CI slot, you can access the module menu. To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CAM module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not have any sound output. This may be incompatible with the CI module and smart card. CI (Common Interface) functions may not be possible depending upon the country broadcasting circumstances.

Viaccess Module

Consultations Authorizations Module information
Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information CI Information

Select the item

This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider. It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

Just Scan

Zoom1 The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped.
You can only select 16:9 (Wide), 4:3, 14:9, Zoom 1/2 in Component (under 720p) mode. You can only select 4:3, 16:9 (Wide) in RGB/HDMI[PC] mode only. In HDMI/Component (over 720p) mode, Just Scan is available. You can only select Original in UK digital teletext (MHEG-5).

PRESET PICTURE SETTINGS

Picture Mode-Preset
It is possible to use Intelligent Sensor in 32/37/42/47/52LG50** models only. G In PLASMA TV models, Backlight will not be displayed.
Aspect Ratio : 16:9 Picture Mode :: Vivid Picture Mode Vivid Backlight Contrast Brightness Sharpness Colour Tint
Intelligent Sensor 100 Vivid Vivid 100 Standard 50 Cinema 70 Sport 70 Game ExpertExpert2
Picture Mode adjusts the TV for the best pic-

Select Picture Mode.

Select desired picture value.
ture appearance. Select the preset value in the Picture Mode menu based on the programme category. When the Intelligent sensor function is on, the most suitable picture is automatically adjusted according to the surrounding conditions. (32/37/42/47/52LG50** only) You can also adjust P i c t u r e M o d e in the Q. M e n u. I n t e l l i g e n t S e n s o r : Adjusts picture according to the surrounding conditions. (32/37/42/47/52LG50** only)
Auto Colour Tone Control (Warm/Medium/Cool)
Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red, or set to cool to see less intense colours with more blue.
Picture Mode : Vivid Backlight 100 Contrast 100 Brightness 50 Sharpness 70 Colour 70 Tint 0 Advanced Control Control
Colour Temperature Fresh Contrast Fresh Colour Noise Reduction Gamma Black Level Eye Care Film Mode
Cool High High Medium Medium High Off Off

Select Advanced Control.

Select Colour Temperature.
Select either Cool, Medium or Warm.
MANUAL PICTURE ADJUSTMENT

Picture Mode-User option

Aspect Ratio : 16:9 Picture Mode :: Vivid Picture Mode Standard (User) Backlight Contrast Brightness Sharpness Colour Tint
Intelligent Sensor Vivid Standard (User) Standard Cinema Sport Game Expert1 Expert2
Select Backlight (LCD TV Only), Contrast, Brightness, Sharpness, Clolour or Tint. Make appropriate adjustments.
You can not adjust colour, sharpness and tint in the RGB-PC mode.
Picture Mode-Expert Control
By segmenting categories, Expert1 and Expert2 provide more categories which users can set as they see fit, offering the optimal picture quality for users.

Select Expert1 or Expert2.

Select Expert Control.

Select your desired Source.
Aspect Ratio : 16:9 Picture Mode :: Vivid Picture Mode Expert1 Backlight Contrast Brightness Sharpness Colour Tint
Intelligent Sensor 100 Vivid 100 Standard 50 Cinema 70 Sport 70 Game ExpertExpert1 Expert2
Backlight Contrast Brightness Sharpness Colour Tint Expert Control Control Picture Reset
100 Contrast Fresh Noise 70 Reduction Gamma 50 Black 50 Level Film Mode 50 Colour Standard 0
White Balance Red Contrast
Off Off Medium High On SD Warm 0
PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast Optimizes the contrast automatically according to the brightness of the reflection. Fresh Colour Adjusts the colour of the reflection automatically to reproduce as close as possible natural colours. Noise Reduction Removes interference up to the point where it does not damage the original picture.
Gamma High gamma values display whitish images and low gamma values display high contrast images.
Colour Temperature Fresh Contrast Fresh Colour Noise Reduction Gamma Black Level Eye Care Film Mode Close
Select Fresh Contrast, Fresh Colour, Noise Reduction or Gamma.

ADVANCED - FILM MODE

To set the TV up for the best picture quality for viewing films. This feature operates only in TV, AV and Component 480i/576i/1080i mode.

Select Film Mode.

ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjusts the TV to best picture quality. This function works in the following mode: AV (NTSC-M), HDMI or Component.
L o w : The reflection of the screen gets darker. H i g h : The reflection of the screen gets

brighter.

A u t o : Realizing the black level of the screen
and set it to High or Low automatically.

Select Black Level.

Select Low or High.

EYE CARE (LCD TV ONLY)

It helps you adjust brightness when the screen is too bright to prevent dazzling.

Select Eye Care.

PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Backlight 100 Contrast 100 Brightness 50 Sharpness 70 Colour 70 Tint 0 Advanced Control Picture Reset
Backlight 100 Contrast 100 Brightness 50 Sharpness video 70 i Resetting configuration. Colour 70 R Tint 0 Advanced Control Picture Reset

Select Picture Reset.

Initialize the adjusted value.
IMAGE STICKING MINIMIZATION (ISM) METHOD

The video function does not work. Check whether the TV is switched on. Try another channel. The problem may be with the broadcast. A Is the power cord inserted correctly into the mains? A Check your antenna direction and/or location. A Test the mains outlet by plugging another TV into the same outlet.

No picture &No sound

Picture appears slowly after switching on
This is normal, the image is muted during the TV startup process. Please contact your service centre, if the picture has not appeared after five minutes.
No or poor colour or poor picture
Adjust Colour in menu option. Allow a sufficient distance between the TV and the VCR. A Try another channel. The problem may be with the broadcast. A Are the video cables installed properly? A Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking Poor reception on some channels Lines or streaks in pictures No picture when connecting HDMI
Check for local interference such as an electrical appliance or power tool.
Station or cable channel experiencing problems, tune to another station. Station signal is weak, reposition the antenna to receive weaker stations. A Check for sources of possible interference.
Check antenna (Change the position of the antenna). Check HDMI cable over version 1.3. If the HDMI cables dont support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
Picture OK & No sound
Press the VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? Adjust Balance in menu option. A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. Check HDMI cable over version 1.3. Check USB cable over version 2.0.
No output from one of the speakers Unusual sound from inside the TV No sound when connecting HDMI or USB
*This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range (Invalid format) Vertical bar or stripe on background & Horizontal Noise & Incorrect position Screen colour is unstable or single colour
Adjust resolution, horizontal frequency or vertical frequency. Check the input source.
Use Auto configure or adjust clock, phase or H/V position. (Option)
Check the signal cable. Reinstall the PC video card.

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.

19LG30** 19LG3000-ZA

22LG30** 22LG3000-ZA
522.2 x 431.5 x 1 89.0 mm 20.6 x 1.0 x 7 inches 7.5 522.2 x 384.2 x 69.0 mm 20.6 x 1 x 2.7 inches 5.2 5.6 kg / 1 lbs 2.4 5.34 kg / 1 lbs 1.8 AC100-240V~ 50/60Hz 0.9A 55W

26LG30** 26LG3000-ZA

663.3 x 508.2 x 227 mm.3 26.1 x 20.1 x 9.0 inches 663.3 x 449.8 x 80.0 mm 26.1 x 1.8 x 3.2 inches 7 10.1 kg / 22.3 lbs 8.6 kg / 19.0 lbs AC100-240V~ 50/60Hz 1.2A 1 20W
458.8 x 391.0 x 1 89.2 mm 1 x 1 x 7 inches 8.1 5.4.5 458.8 x 344.5 x 69.0 mm 1 x 1 x 2.7 inches 8.1 3.6 1.1 5.02 kg / 1 lbs 4.76 kg / 10.5 lbs AC100-240V~ 50/60Hz 0.8A 50W

32LG30** 32LG3000-ZA

37LG30** 37LG3000-ZA
919.6 x 682.3 x 293.8 mm 36.2 x 26.9 x 1 inches 1.6 919.6 x 610.3 x 89.0 mm 36.2 x 24.0 x 3.5 inches 1 kg / 41.5 lbs 8.kg / 35.7 lbs 6.2 AC100-240V~ 50/60Hz 1.8A 1 80W

42LG30** 42LG3000-ZA

1032.8 x 742.3 x 293.8 mm 40.7 x 29.3 x 1 inches 1.6 1032.8 x 670.1 x 92.0 mm 40.7 x 26.4 x 3.7 inches 23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs
801.8 x 604.2 x 227 mm.3 31.6 x 23.8 x 9.0 inches 801.8 x 544.1 x 79.0 mm 31.6 x 21.5 x 3.2 inches 1 kg / 29.6 lbs 3.kg / 26.3 lbs 1.9 AC100-240V~ 50/60Hz 1.5A 1 50W
Weight Power requirement Power Consumption Television System Programme Coverage
AC100-240V~ 50/60Hz 2.3A 230W
External Antenna Impedance Operating Temperature Environment condition Operating Humidity Storage Temperature Storage Humidity
32LG50** MODELS 32LG5000-ZA 32LG5010-ZD 32LG5020-ZB 32LG5030-ZE
81 x 598.8 x 231.9 mm 3.8 32.1 x 23.6 x 9.2 inches 81 x 540.4 x 95.5 mm 3.8 32.1 x 21.3 x 3.8 inches 1 kg / 31.1 lbs 4.kg / 27 lbs 2.6.8 AC100-240V~ 50/60Hz 1.5A 1 50W
37LG50** 37LG5000-ZA 37LG5010-ZD 37LG5020-ZB 37LG5030-ZE
936.4 x 685.4 x 293.4 mm 36.9 x 27 x 1 inches.0 1.6 936.4 x 61 x 88.0 mm 2.8 36.9 x 24.2 x 3.5 inches 1 kg / 40.4 lbs 8.kg / 34.4 lbs 5.6 AC100-240V~ 50/60Hz 1.8A 1 80W
42LG50** 42LG5000-ZA 42LG5010-ZD 42LG5020-ZB 42LG5030-ZE

* When setting the 15 ~ 24, a menu does not appear on screen.

Error Acknowledgement

[Command2][ ][Set ID][ ][NG][Data][x] * The TV transmits ACK (acknowledgement) based on this format when receiving abnormal data from nonviable functions or communication errors.

01. Power (Command: k a)

G To control Power On/Off of the TV.
04. Volume Mute (Command: k e)
G To control volume mute on/off.
[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off Ack

G To show Power On/Off.

You can also adjust mute using the MUTE button on remote control. Transmission 01 : Power On [k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off) 01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x] 05. Volume Control (Command: k f)

G To adjust volume.

[a][ ][Set ID][ ][OK/NG][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
[a][ ][Set ID][ ][OK/NG][Data][x] * Similarly, if other functions transmit 0xFF data based on this format, Acknowledgement data feed back presents status about each function. * OK Ack. ,Error Ack. and other message maybe display on the screen when TV is power On. 02. Aspect Ratio (Command: k c) (Main Picture Size)
G To adjust the screen format. (Main picture format)
You can also adjust volume with the VOLUME buttons on remote control. Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 14. * Refer to Real data mapping 1. See page 1 Ack [f][ ][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g)
G To adjust screen contrast.
You can also adjust the screen format using the A s p e c t R a t i o in the Q.MENU. or PICTURE menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 01 : 02 : 04 : 05 : Normal screen (4:3) Wide screen (1 6:9) Zoom1 Zoom: Original 07 : 1 4:: Just Scan
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 14. * Refer to Real data mapping 1. See page 1 Ack [g][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness (Command: k h) G To adjust screen brightness. You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 14. * Refer to Real data mapping 1. See page 1 Ack [h][ ][Set ID][ ][OK/NG][Data][x] 08. Colour (Command: k i)
G To adjust the screen colour.

[m][ ][Set ID][ ][OK/NG][Data][x] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released.
16. ISM Method (Plasma TV only) (Command: j p )
G To control the ISM method. You can also adjust ISM
19. Equalize (Command : j v)

G To adjust equalize.

Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data 01: Inversion 02: Orbiter 04: White wash 08: Normal
[j][v][ ][Set ID][ ][Data][Cr] MSB Data : 0 LSB 0
[p][ ][Set ID][ ][OK/NG][Data][x]
17. Power Saving (Plasma TV only) (Command: j q)
G To reduce the power consumption of the TV. You can also
Frequency Step Frequency : 0 120Hz 1 200Hz 2 500Hz 3 1.2kHz 4 3kHz 5 7.5kHz 6 12kHz Step (Frequency data): Refer to Real data mapping 3. See page 1 15.
[v][ ][Set ID][ ][OK/NG][Data][x] * Euqalize command expression Step 0. 0. 0. 1. 0. 1. 0. 1. 0. 1. Frequency 120Hz 200Hz 500Hz 1.2KHz 3KHz 7.5KHz 12KHz OSD Value -24. 0. 24
adjust Low Power in OPTION menu. Transmission [j][q][ ][Set ID][ ][Data][Cr] Data Min :00 ~ Max :04 (*transmit by hexadecimal code)
[q][ ][Set ID][ ][OK/NG][Data][x]
18. Auto Configure (Command: j u)
G To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01: To set Ack [u][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping : Step 0 A : Step 10 (Set ID 10) F : Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) 64 : Step 100 6E : Step 73 : Step 74 : Step C7: Step 199 FE : Step 254 FF : Step 255
* Real data mapping :-: -:-:0 4E : +38 4F : +: +40
Ex) If you wish to set frequency 500Hz and -20 value on menu OSD, refer to Real data mapping 3 and then find Step value for -20. 010 (500Hz) 0001 1(Step 3) => 0100001 => (Hexadecimal) : [j][v][ ][Set ID][ ][43][Cr] * 3 bits of Frequency and 5 bits of Step makes 8 bits (1 byte). Change 8 bits to Hexadecimal code.
20. Tune Command (Command: m a)
G Select channel to following physical number.
24. Input select (Command: x b) (Main Picture Input)
G To select input source for main picture.
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr] Data 00 : High channel data Data 01 : Low channel data ex. No. 47 -> 00 2F (2FH) No. 394 -> (188H), DTV No. 0 -> Dont care Data 02 : 0x00 : ATV, 0x10 : DTV, 0x20 : Radio Channel data range Analogue - Min: 00 ~ Max: 63 (0~99) Digital - Min: 00 ~ Max: 3E7 (0~999) Ack [a][ ][Set ID][ ][OK/NG][Data][x] Data Min: 00 ~ Max: 7DH

[x][b][ ][Set ID][ ][Data][Cr] Data Structure MSB 0 LSB 0
External Input External Input 1
Input Number Data DTV Analogue AV Component RGB HDMI Data 0 Input1 Input2 Input3
21. Channel Add/Skip (Command: m b)
G To set skip status for the current Programme.
[m][b][ ][Set ID][ ][Data][Cr] Data 00 : Skip 01 : Add

Input Number 1

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

22. Key (Command : m c)

G To send IR remote key code.
[m][c][ ][Set ID][ ][Data][Cr] Data Key code - Refer to page 108.
[b][ ][Set ID][ ][OK/NG][Data][x]
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
23. Control Back Light (LCD TV only) (Command: m g)
G To Cont rol t he back light.
[m][g][ ][Set ID][ ][Data][Cr] Data : Min: 00 ~ Max: 64 (*transmit by hexadecimal code)
[g][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping 3 (Equalize) Step: OSD Step: OSD 00 : -: : -: : -: : -: : -: : -: : -: : -: : -: : -: : -: 1 : -: : -: : -: : -: : : 24

LCD TV OWNERS MANUAL

LCD TV MODELS L S 4 D* L G 3 0* * L S 4 D* L G 3 2* * L G 2 0* * L G 3 0* * L G 2 0* * L G 3 0* * L G 2 0* * L G 3 2* * L G 3 0* * L G 5* * * L G 3 0* * L G 5 0* * L G 3 0* * L G 5 0* * L G 5 0* * L G 5 0* * Please read this manual carefully before operating your TV. Retain it for future reference. Record model number and serial number of the TV. Refer to the label on the back cover and quote this information. To your dealer when requiring service.
5507: 19LS4D-ZD 5721: 26LG3050-ZA 5631: 42LG2000-ZA 5090: 22LG3000-ZA 5089: 32LG3000-ZA 5086: 42LG3000-ZA 5084: 37LG5000-ZA 5082: 47LG5000-ZA 5385: 52LG5010-ZD 5387: 42LG5010-ZD 5389: 32LG5010-ZD 5391: 47LG5020-ZB 5393: 37LG5020-ZB 5395: 52LG5030-ZE 5397: 42LG5030-ZE 5399: 32LG5030-ZE 5820: 19LG3050-ZA 5879: 19LG3060-ZB 5878: 32LG5600-ZB 651 42LG3200-ZA 1:
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
I D N u m b e r ( s ) : 5499: 22LS4D-ZD 5629: 32LG2000-ZA 5630: 37LG2000-ZA 5088: 19LG3000-ZA 5080: 26LG3000-ZA 5087: 37LG3000-ZA 5085: 32LG5000-ZA 5083: 42LG5000-ZA 5081: 52LG5000-ZA 5386: 47LG5010-ZD 5388: 37LG5010-ZD 5390: 52LG5020-ZB 5392: 42LG5020-ZB 5394: 32LG5020-ZB 5396: 47LG5030-ZE 5398: 37LG5030-ZE 5671: 32LG5700-ZF 5818: 22LG3050-ZA 5880: 22LG3060-ZB 6507: 32LG3200-ZA
Extended Owners Manual that contains advanced features of these LG TV-sets is located on CD-ROM in electronic version. To read it You need to open chosen files by using Personal Computer (PC) equipped with CD-ROM drive.
P/NO: MFL34441652 (0901-REV01) Printed in Korea

CONNECTING YOUR UNIT

Image shown may differ from your TV.

DVD/STB

COMPONENT IN

VIDEO AUDIO

VCR Connection

Power Cord

USB IN SERVICE ONLY
AUDIO IN OPTICAL DIGITAL (RGB/DVI) AUDIO OUT

HDMI/DVI IN 2

RGB IN (PC)
1(DVI) RS-232C IN (CONTROL & SERVICE)
* To connect an additional equipment, see the E x t e r n a l e q u i p m e n t S e t u p section in CD Manual.

ANTENNA IN

Antenna Connection

ENGLISH

HDMI/DVI IN AUDIO IN (RGB/DVI) ANTENNA IN PCMCIA CARD SLOT EJECT
RS-232C IN (CONTROL & SERVICE)

RGB (PC) IN

COMPONENT IN VIDEO AUDIO

SERVICE ONLY

SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product. In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product

WARNING

Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.

CAUTION

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Precautions in Moving the Product
Do not use the product in damp place such as a bathroom or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Make sure to turn off the product. Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
Do not shock the product when moving it.
Install the product on a flat and stable place that has no risk of dropping the product.
- If the product is dropped, you may be injured or the product may be broken.
Make the panel face forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair.
Precautions in Using the Product
Do not disassemble, repair or modify the product at your own discretion.
- Fire or electric shock accident can occur. - Contact the service center for check, calibration or repair.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation such as bookcase or rack.

- Ventilation required.

Electrical Power Related Precautions
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not keep a still image on the screen for an extended period (e.g. by pausing a video) as the fixed image may remian visible on the screen. This is known as image burn. Image burn is not covered under the manufacturers warranty.
Do not touch the power plug with wet hands. Additionally, it the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the power cable or signal cable.
- You may be electrocuted or a fire can break out.

PREPARATION

FRONT PANEL CONTROLS
Image shown may differ from your TV. If your TV has a protection film attached, remove the film and then wipe the TV with a polishing cloth.
LCD TV Models : 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42/47/52LG5***

PROGRAMME

VOLUME
Intelligent Sensor Adjusts picture according to the surrounding conditions. (32/37/42/47/52LG5*** only) POWER Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates blue when the TV is switched on. Note: You can adjust Power Indicator
LCD TV Models : 19/22LG30**
INPUT MENU OK VOLUME PROGRAMME

in the OPTION menu.

INPUT MENU OK
LCD TV Models : 19/22LS4D*
POWER INPUT MENU OK VOLUME PROGRAMME
Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates green when the TV is switched on.

BACK PANEL INFORMATION

PCMCIA CARD SLOT

HDMI IN 3

HDMI/DVI IN

AUDIO IN (RGB/DVI)

PCMCIS CARD SLOT

VIDEO L/MONO AUDIO R

1(DVI)
Except for 32/37/42LG20**, 32/42LG32**

S-VIDEO

AV IN 3

AV IN 3 H/P

Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. RGB/DVI Audio Input Connect the audio from a PC or DTV.
Component Input Connect a component video/audio device to these jacks. Antenna Input Connect RF antenna to this jack. PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) Audio/Video Input (Except for 19/22LS4D*) Connect audio/video output from an external device to these jacks. S-VIDEO (Except for 19/22LS4D*, 32/37/42LG20**, 32/42LG32**) Connect S-Video out from an S-VIDEO device. Headphone Socket (Except for 19/22LS4D*, 32/37/42LG20**, 32/42LG32**) Connect the headphone plug to this socket. SERVICE ONLY PORT

DIGITAL AUDIO OUT OPTICAL (Except for 19/22LS4D*) Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. HDMI Input Connect a HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable. RGB IN (PC) Connect the output from a PC. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.

STAND INSTALLATION

(LCD TV Models: 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Assemble the parts of the S t a n d B o d y with the C o v e r B a s e of the TV.
Fix the 4 bolts securely using the holes in the back of the TV.

Stand Body

Cover Base

(Only 19/22LG30**)

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the TV. Insert the S T A N D B O D Y into a C O V E R B A S E until clicking sound. Assemble the TV as shown.

DETACHING STAND

(Only 19/22LS4D*)
Image shown may differ from your TV. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Place the tv with its front facing downward on a cushion or soft cloth.
Hold the H i n g e B o d y and bend it upward.

Hinge Body

Pull the C o v e r B a s e backward during pressing a button on the S t a n d B o d y.
Insert the S t a n d B o d y into the TV until clicking sound.
Hold the C o v e r B a s e and pull with shake it backward to separate from the S t a n d B o d y.

Hold the S t a n d B o d y and bend it upward.
Pull stand body to separate from the TV during pressing 2 latches.
BACK COVER FOR WIRE ARRANGEMENT
LCD TV Models: 32/37/42LG20**, 26/32/37/ 42LG30**, 32/42LG32**, 32/37/42/47/52LG5***
LCD TV Models : 19/22LS4D*, 19/22LG30**
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. Open the C A B L E M A N A G E M E N T C L I P as shown and manage the cables.
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section.

CABLE MANAGEMENT CLIP

Install the CABLE MANAGEMENT CLIP as shown.
Fit the C A B L E M A N A G E M E N T C L I P as shown.
How to remove the cable management clip
First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward. Hold the CABLE MANAGEMENT CLIP with both hands and pull it backward.

! NOTE

G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
You should purchase necessary components to fix the TV to the wall on the market. Position the TV close to the wall to avoid the possibility of it falling when pushed. The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen these bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the TV.
When moving the TV undo the cords first. Use a platform or cabinet strong and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV.

4 inches

Attaching the TV to a desk (Only 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. Stand
1-Screw (provided as parts of the product)

! WARNING

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
4 inches 4 inches 4 inches 4 inches
Not using the desk-type stand (Except for 19/22LS4D*)
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the P R O T E C T I O N C O V E R into the TV until clicking sound.
To prevent damage do not connect to the mains outlet until all connections are made between the devices.

ANTENNA CONNECTION

For optimum picture quality, adjust antenna direction. An antenna cable and converter are not supplied.

Wall Antenna Socket

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

HDMI IN RGB IN

VARIABLE AUDIO OUT

RF Coaxial Wire (75 ohm)

Outdoor Antenna (VHF, UHF)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Antenna

Signal Amplifier
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above. If signal needs to be split for two TVs,use an antenna signal splitter for connection.
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.

TV D/A POWER INPUT

TV/RADIO TEXT I/II MUTE

7 LIST

9 Q.VIEW

AV MODE

INFO i

VOL EXIT RETURN

INPUT External input mode rotate in regular sequence. Switches the TV on from standby. GUIDE Shows programme schedule. THUMBSTICK(Up/Down/LeftRight) Allows you to navigate the on-screen menus and adjust the system settings to your preference. OK Accepts your selection or displays the current mode. Programme UP/DOWN Selects a programme. Q.VIEW Returns to the previously viewed programme.
MODE Selects the remote operating modes. Q. MENU Select the desired quick menu source. MENU Selects a menu. Clears all on-screen displays and returns to TV viewing from any menu. VOLUME UP /DOWN Adjusts the volume. POWER Switches the TV on from standby or off to standby.

Installing Batteries

Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -). Install two 1.5V AAA batteries. Do not mix old or used batteries with new ones. Close cover.

TURNING ON THE TV

- When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. (or PR D E) button on the TV or In standby mode to turn TV on, press the r / I, INPUT or P press the POWER, INPUT, D/A, P (or PR + -) or NUMBER button on the remote control and the TV will switch on.

Initializing setup

If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the Language, Select Mode, Country, Time Zone, Auto programme tuning.
Note: a. It will automatically disappear after approx. 40 seconds unless a button is pressed. b. Press the BACK or RETURN button to change the current OSD to the previous OSD. c. For those countries without confirmed DTV broadcasting standards, some DTV features might not work, depending on the DTV broadcasting environment. d. "Home mode is the optimal setting for home environments, and is the TV's default mode. e. "In Store" mode is the optimal setting for store environments. If a user modifies image quality data, In Store mode initializes the product to the image quality set by us after a certain period of time. f. The mode (Home, In Store) can be changed by executing Factory Reset in the OPTION menu.

ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
Select your desired language.

Select your country.

* If you want to change Language/ Country selection
Select O P T I O N. Select M e n u L a n g u a g e or C o u n t r y.
Select your desired language or country. Save it.

G G G G G

If you do not finish the set-up Installation Guide by pressing RETURN or if you time out on the OSD (On Screen Display) the installation menu will continuously appear until the set up is completed whenever the TV is switched on If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. The CI (Common Interface) function may not be applied based on country broadcasting circumstances. DTV mode control buttons may not function based on country broadcasting circumstances. In country that Digital broadcasting regulation isnt fixed, some DTV function may not work depending on digital broadcasting circumstances. The Country Setting UK should only be activated UK.
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. SETUP

Move OK

Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information

PICTURE

Aspect Ratio Picture Mode : 16:9 : Vivid Backlight Contrast Brightness Sharpness Colour Tint
Auto Volume Balance Sound Mode : Off 0 : Standard 120Hz 200Hz 500Hz 1.2KHz 3KHz

OPTION

+ + + + +
Clock Off Time On Time Sleep Timer Auto Sleep Time Zone
Menu Language Audio Language Subtitle Language Hard of Hearing( Country Input Label SIMPLINK Key Lock
: Off : Off : Off : Off : Canary GMT
: English : English : English ) Off :UK : Off : Off
Lock System : Off Set Password Block Programme Parental Guidance : Off

1MENU 2

Display each menu.

Select a menu item.

Move to the pop up menu. Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

AUTO PROGRAMME TUNING

Use this to automatically find and store all available programmes. When you start auto programming in digital mode, all previously stored service information will be deleted.
Auto tuning Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information
All service-information will be updated. Continue? Yes

SECAM L Search

Select SETUP.
Use NUMBER buttons to input a 4-digit
password in Lock System On.
If you wish to keep on auto tuning select YES

Select Auto Tuning.

using the button. Then, press the OK button. Otherwise select NO.

Select Yes.

Run Auto tuning.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

APPENDIX

MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Do not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to protect against possible damage from lightning or power surges.
TO VIEW THE USER'S GUIDE ON THE CD-ROM
To view the User's guide on the CD-ROM, Adobe Acrobat Reader must be installed on your PC. The "ACRORD" folder on the CD-ROM contains the installation program for Acrobat Reader. If you want to install Acrobat Reader, Open "My Computer" Open the folder "LG" Open the folder "ACRORD" double-click your language. To view the User's guide The User's guide files are included in the supplied CD-ROM. Load the supplied CD-ROM into the CD-ROM drive of your PC. After a while, the web page of the CD-ROM will open automatically.(Windows users only) If the web page does not appear automatically, open the User's guide file directly. Open "My computer" Open the folder "LG" Double click the "index.htm" file.

TROUBLESHOOTING

The TV does not operate properly. Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Ensure that the correct remote operating mode is set: TV, VCR etc. A Install new batteries.
The remote control does not work
Power is suddenly turned off
Is the sleep timer set? Check the power control settings. Has the Power supply been interrupted. A Is Auto sleep activated on this station?
The video function does not work.

No picture &No sound

Check whether the TV is switched on. Try another channel. The problem may be with the broadcast. A Is the power cord inserted correctly into the mains? A Check your antenna direction and/or location. A Test the mains outlet by plugging another TV into the same outlet.
Picture appears slowly after switching on
This is normal, the image is muted during the TV startup process. Please contact your service centre, if the picture has not appeared after five minutes.
No or poor colour or poor picture
Adjust Colour in menu option. Allow a sufficient distance between the TV and the VCR. A Try another channel. The problem may be with the broadcast. A Are the video cables installed properly? A Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking Poor reception on some channels Lines or streaks in pictures No picture when connecting HDMI
Check for local interference such as an electrical appliance or power tool.
Station or cable channel experiencing problems, tune to another station. Station signal is weak, reposition the antenna to receive weaker stations. A Check for sources of possible interference.
Check antenna (Change the position of the antenna). Check HDMI cable over version 1.3. If the HDMI cables dont support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
Picture OK & No sound
Press the VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? Adjust Balance in menu option. A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. Check HDMI cable over version 1.3. Check USB cable over version 2.0.

No output from one of the speakers Unusual sound from inside the TV No sound when connecting HDMI or USB
*This feature is not available for all models.
There is a problem with PICTURE settings. When the user changes the picture settings, the TV automatically converts back to the initial settings after a certain period of time.
It means that the TV is currently set to I n S t o r e mode. To switch to H o m e mode you should do the followings: From the TV Menu, choose O P T I O N -> F a c t o r y R e s e t -> Y e s (wait for a W few seconds for the TV to download again) -> OSD "W E L C O M E" appears -> Press O K button -> Choose L a n g u a g e -> Choose H o m e -> Select your C o u n t r y and T i m e Z o n e -> Press O K button. Program search will begin automatically (You can stop the search by pressing the O K button). Now, you have completed switching to the H o m e mode.

WEIGHT

19LS4D* MODELS 19LS4D-ZD 22LS4D-ZD 22LS4D* 19LG30** 19LG3000-ZA 19LG3050-ZA 19LG3060-ZB
5.02 kg / 1 lbs 1.1 4.76 kg / 10.5 lbs

Weight

with stand without stand
5.1 kg / 1 lbs 1.3 4.6 kg / 10.2 lbs
6.1 kg / 1 lbs 3.5 5.7 kg / 1 lbs 2.6
22LG30** MODELS 22LG3000-ZA 22LG3050-ZA 22LG3060-ZB
5.6 kg / 1 lbs 2.4 5.34 kg / 1 lbs 1.8
26LG30** 26LG3000-ZA 26LG3050-ZA
10.1 kg / 22.3 lbs 8.6 kg / 19.0 lbs
32LG30** 32LG3000-ZA 32LG3030-ZA
1 kg / 29.6 lbs 3.kg / 26.3 lbs 1.9
37LG30** MODELS 37LG3000-ZA 37LG3030-ZA
1 kg / 41.5 lbs 8.kg / 35.7 lbs 6.2
42LG30** 42LG3000-ZA 42LG3030-ZA
23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs

32LG20** 32LG2000-ZA

37LG20** 37LG2000-ZA
42LG20** MODELS 42LG2000-ZA

32LG32** 32LG3200-ZA

42LG32** 42LG3200-ZA
32LG5*** 32LG5000-ZA 32LG5010-ZD 32LG5020-ZB 32LG5030-ZE 32LG5600-ZB 32LG5700-ZF
1 kg / 31.1 lbs 4.kg / 27 lbs 2.6.8
37LG50** MODELS 37LG5000-ZA 37LG5010-ZD 37LG5020-ZB 37LG5030-ZE

1 kg / 40.4 lbs 8.kg / 34.4 lbs 5.6
42LG50** 42LG5000-ZA 42LG5010-ZD 42LG5020-ZB 42LG5030-ZE
26.2 kg / 57 lbs.8 23.5 kg / 51.8 lbs
47LG50** 47LG5000-ZA 47LG5010-ZD 47LG5020-ZB 47LG5030-ZE
29.2 kg / 64.4 lbs 24.6 kg / 54.3 lbs
52LG50** 52LG5000-ZA 52LG5010-ZD 52LG5020-ZB 52LG5030-ZE
39.5 kg / 87 lbs.1 34.9 kg / 77 lbs.0
The specifications shown above may be changed without prior notice for quality improvement.

(UK only)