Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the back of the TV.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
You should purchase necessary components to fix the TV to the wall on the market. Position the TV close to the wall to avoid the possibility of it falling when pushed. A The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen then bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with bolts to the wall. Ensure that both brackets are even.
Use a strong cord to secure the TV. Secure the cord in such a way that it becomes taught when the TV is in position.

! NOTE

When moving the TV undo the cords first. Use a platform or cabinet string and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
BACK COVER FOR WIRE ARRANGEMENT
Here shown may be somewhat different from your TV.
Connect the cables as necessary. To connect additional equipment, see the E x t e r n a l E q u i p m e n t S e t u p section.
Connect the cables as necessary.
To connect additional equipment, see the E x t e r n a l E q u i p m e n t S e t u p section.
Install the C A B L E M A N A G E M E N T C L I P as shown.

CABLE MANAGEMENT CLIP

Fix the Cable Holder as shown and bundle the cables.
Fix the C a b l e H o l d e r as shown and bundle the cables.
How to remove the cable management clip
Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward.
* For the 42PG1*** model, press the center of the CABLE MANAGEMENT CLIP and then lift up it.
Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.
Arrange the cables as shown picture.

Swivel Stand

RGB(PC) 2C IN TROL) VIDEO
Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O jacks on the TV.
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.)
Select C o m p o n e n t input source using the I N P U T button on the remote control.
Signal 480i/576i 480p/576p 720p/1080i 1080p
Component Yes Yes Yes Yes (Only 50Hz, 60Hz)
HDMI1/DVI, HDMI2(Only 42/50PG2***) No Yes Yes Yes (24Hz, 30Hz, 50Hz, 60Hz)
RS-232C IN (CONTROL&SERVICE) (CONTROL&SER

AUDIO I (RGB/DV

RGB IN (P (PC)
Connecting a set-top box with an HDMI cable
Connect the HDMI output of the digital set-top box to the H D M I / D V I I N or H D M I I N 2(Except 42/50PG1***) models jack on the TV.

RS-232C IN (CONTROL)

HDMI IN 2

RGB(PC)

Select H D M I 1 / D V I or H D M I 2(Except 42/50PG1***) input source using the I N P U T button on the remote control.
TV can receive the video and audio signal simultaneously with using a HDMI cable. G If the digital set-top box supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1280x720p. G If the digital set-top box player does not support Auto HDMI, you need to TV the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.
RS-232C IN (CONTROL&SERVICE)
Connecting with a HDMI to DVI cable
RS-232C IN (CONTROL&SERVICE) (CONTROL&SERVICE)
RGB(PC) RS-232C IN (CONTROL)

ANTENNA ANTEN IN

Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 jack on the TV.
Connect the audio output of the digital set-top box to the A U D I O ( R G B / D V I ) jack on the TV.
Select H D M I 1 / D V I input source using the I N P U T button on the remote control.

1 ! NOTE

HDMI2 (Except 42/50PG1***)source does not support DVI source. If the set-top has a DVI output and no HDMI output, a separated audio connection is necessary. If the set-top Box does not support Auto DVI, you need to set the output resolution appropriately.

DVD SETUP

RGB(PC) 2C IN TROL)
Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the TV.
Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the TV.
Turn on the DVD player, insert a DVD.
Refer to the DVD player's manual for operating instructions.
Only 32PC5*** Component Input ports
To achieve better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV

Y PB PR

AUDI (RGB

PB B-Y Cb Pb

PR R-Y Cr Pr
Video output ports on DVD player
When connecting with a Euro Scart

Connect the Euro scart socket of the DVD to the A V 1 Euro scart socket on the set. Turn on the DVD player, insert a DVD. Select A V 1 input source with using the I N P U T button on the remote control. If connected to A V 2 Euro scart socket, select A V 2 input source. Refer to the DVD player's manual for operating instructions.

AUDIO/ VIDEO

(R) AUDIO (L)

AV 2 AV 1

If you want to use the EURO scart cable, you have to use the signal shielded Euro scart cable. COMPONENT IN RS-232C IN N
(CONTROL&SERVICE) VICE)

RGB IN 2 C) AV 1 AV (PC)

Connecting with a S-Video cable (Except 42/50PG1***, 32PC5***)
Connect the S-VIDEO output of the DVD to the S - V I D E O input on the TV.

VIDEO S-VIDEO

ANT IN
Connect the audio outputs of the DVD to the A U D I O input jacks on the TV.

OUTPUT SWITCH

ANT OUT
Select A V 3 input source using the I N P U T button on the remote control.

AV IN 3

Connecting the HDMI cable

HDMI/DVI IN 1 HDMI IN 2

Connect the HDMI output of the DVD to the H D M I 1 / D V I I N or H D M I I N 2(Except 42/50PG1***) jack on the TV.
RS-232C IN (CONTROL&SERVICE) (CONTROL&SE AUDIO IN (RGB/DVI)

AUDIO (RGB/D AV 2

VIDEO The TV can receive video and audio signals simultaneously when using a HDMI cable. G If the DVD player supports Auto HDMI function, the output resolution of the source device will be automatically TV to 1280x720p. 1 G If the DVD player does not support Auto HDMI, you must TV HDMI/DVI IN the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

RGB IN (PC) HDMI IN

VCR SETUP
To avoid picture noise (interference), allow adequate distance between the VCR and TV. Typically a frozen still picture from a VCR. If 4:3 picture format is used for an extended period the fixed images on the sides of the screen may remain visible.
Connecting with a RF cable

ANT OUT S-VIDEO VIDEO

S-VIDEO
ANT IN OUTPUT SWITCH ANT IN OUTPUT SWITCH

Wall Jack

Connect the A N T O U T socket of the VCR to the A N T E N N A I N socket on the TV.
Connect the antenna cable to the A N T I N socket of the VCR.
IN Press the P L A Y button on the VCR and match the appropriate programme between the TV and VCR for viewing.

ANTENNA

Connect the Euro scart socket of the VCR to the A V 1 Euro scart socket on the set. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.)

Select A V 1 input source with using the I N P U T button on the remote control.
If connected to A V 2 Euro scart socket, select A V 2 input source.
If you want to use the EURO scart cable, you have to use the signal shielded Euro scart cable.
RS-232C IN 2C (CONTROL&SERVICE) SERVICE)
RGB AV AUDIO IN IN (PC) 2 (RGB/DVI)
When connecting with a RCA cable (Except 42/50PG1***, 32PC5***)
V Connect the A U D I O/V I D E O jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.)
If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the set.
When connecting with an S-Video cable (Except 42/50PG1***, 32PC5***)
Connect the S-VIDEO output of the VCR to the S - V I D E O input on the set. The picture quality is improved; compared to normal composite (RCA cable) input. Connect the audio outputs of the VCR to the A U D I O input jacks on the set. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select A V 3 input source with using the I N P U T button on the remote control.
If both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received.
OTHER A/V SOURCE SETUP(Except 42/50PG1***, 32PC5***)

Camcorder

Video Game Set
V Connect the A U D I O/V I D E O jacks between TV and external equipment. Match the jack colours. (Video = yellow, Audio Left = white, and Audio Right = red)
Operate the corresponding external equipment. Refer to external equipment operating guide.

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable

COMPONENT IN NENT

HDMI/DVI IN HDMI IN

RGB(PC) 2C IN ROL)

ANTENNA AN IN

RGB OUTPUT

Connect the RGB output of the PC to the R G B ( P C) jack on the TV.
Connect the PC audio output to the A U D I O jack on the TV.
Turn on the PC and the TV.
Select R G B P C input source using the I N P U T button on the remote control.
To enjoy vivid picture and sound, connect the PC to the TV. G Avoid keeping a fixed image on the TV s screen for prolonged periods of time.The fixed image may become permanently imprinted on the screen;use a screen saver when possible. G Connect the PC to the RGB (PC) port of the TV; change the resolution output of PC accordingly. G There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. G The synchronization input waveform for Horizontal and Vertical frequencies are separate.

We recommend using 1024 x 768, 60Hz (32PC5*** VGA PLASMA TV Models)1024 x 768, 60Hz (42PG1***,42PG2*** XGA PLASMA TV Models)/1360 x 768, 60Hz(50PG1***, 50PG2***) for the PC mode, these should provide the best picture quality. G If the resolution of PC is over SXGA, there will be no picture on the TV. G Connect the audio cable from the PC to the Audio input on the TV.(Audio cables are not included with the TV). G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of the cable. This provides the best picture quality.
Supported Display Resolution
RGB-PC mode Resolution 640x350 720x400 640x480 800x600 848x480 852x480 1024x768 1280x768 1360x768 Horizontal Frequency(kHz) 31.468 31.469 31.469 37.879 29.48.363 47.776 47.720 Vertical Frequency(Hz) 70.09 70.09 59.94 60.317 59.75 60.491 60.004 59.87 59.799
HDMI-DTV mode Resolution 720x480 720x576 1280x720 Horizontal Frequency(kHz) 31.47 31.50 31.25 44.96 45.00 37.50 33.72 33.75 28.125 67.432 67.5 56.33.75 Vertical Frequency(Hz) 59.94 60.00 50.00 59.94 60.00 50.00 59.94 60.00 50.00 59.30

1920x1080i

1920x1080p

Only 50PG1***, 50PG2***

Screen Setup for PC mode
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. Auto configure This function is for automatic adjustment of the screen position, clock, and phase. The displayed image will be unstable for a few seconds while the auto configuration is in progress.

Picture

Press the M E N U button and then use select the P i c t u r e menu.

button to

Press the S c r e e n.

button and then use

button to select
Picture Mode Colour Temperature XD Advanced Aspect Ratio Picture Reset Screen

DE F G OK RETURN

Press the button and then use A u t o C o n f i g.
Picture Picture Mode Colour Temperature XD Advanced Aspect Ratio Picture Reset Screen Screen

Press the

button to start A u t o C o n f i g.

To Set

When Auto config. has finished, OK will be shown on screen. If the position of the image is still not correct, try Auto adjustment again.
Screen Config. Auto config. Manual Config. XGA Mode Reset
If picture needs to be adjusted again after Auto adjustment in RGB (PC), you can adjust the M a n u a l C o n f i g.
Press the M E N U button to return to normal TV viewing. Press the R E T U R N button to move to the previous menu screen.
Manual Configure (Adjustment for screen Phase, Clock, Position) (RGB [PC] mode only)

If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. To correct the screen size, adjust C l o c k. Its not available to use Phase, Clock function in COMPONENT (480i/480p/576i/576p/720p/1080i/1080p), HDMI (480p/576p/720p/1080i/1080p). C l o c k This function is to minimize any vertical bars or stripes visible on the screen background the horizontal screen size will also change. P h a s e This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Picture Picture Mode Colour Temperature XD Advanced Aspect Ratio Picture Reset Screen
Press the button and then use M a n u a l C o n f i g.
Press the button and then use / button to select P h a s e, C l o c k, H - P o s i t i o n or V - P o s i t i o n.

Screen

button to make appropriate adjustments.
Auto config. Manual Config. XGA Mode Reset
Phase Clock H-Position V-Position
Selecting XGA/VGA mode (Only 50PG1***, 50PG2***, 32PC5***)
This feature is not available for all models. To view a normal picture, match the resolution of RGB mode and selection of XGA/VGA mode.
This function works in the following mode: RGB[PC] mode.
Press the button and then use X G A M o d e or V G A M o d e.
Screen Auto Config. Manual Config. XGA Mode Reset
Press the button and then use the desired XGA/VGA resolution.
1024x768 1280x768 1360x768

* Only VGA Mode

Screen Auto Config. Manual Config. XGA Mode VGA Reset

640x480 848x480 852x480

Initializing (Reset to original factory settings)
This function operates in current mode. To initialize the adjusted value
Press the MENU button and then use select the P i c t u r e menu.

Press the R e s e t.

button.
Screen Auto config. Manual Config. XGA Mode Reset
WATCHING TV / PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS (ONLY 42/50PG2***)
When using the remote control, aim it at the remote control sensor on the TV. RATIO Selects your desired picture format. SOUND To select the sound appropriate to your viewing programme. POWER Switches the TV on from standby or off to standby. PICTURE Adjusts the factory preset picture according to the room. INPUT External input mode rotate in regular sequence. Switches the TV on from standby.

Press the button and then U s e r 1 or U s e r 2.
Press the button and then / button to select the C desired picture option (C o n t r a s t, B r i g h t n e s s, C o l o u r, S h a r p n e s s and T i n t).
Contrast Contrast Brightness Colour Sharpness Tint

Contrast

You cannot adjust colour, sharpness and tint in the RGB-PC mode.
Colour Tone - User Option
To adjust red, green, blue to any colour temperature you prefer. This menu is activated after selecting User1 or User2 in the Picture Mode.
Picture Picture Mode Colour Temperature Colour Temperature XD Advanced Aspect Ratio Picture Reset Screen Cool Medium Warm User

Press the U s e r.

Press the button and then G r e e n or B l u e.

button to select R e d,

User Red Green Blue +30 +0
- PICTURE IMPROVEMENT TECHNOLOGY
XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. It is not possible to use this function in RGB-PC mode.
Press the MENU button and then the P i c t u r e menu.

button to select X D.

Press the button and then A u t o or M a n u a l.

* Manual Selection

This menu is activated after selecting the U s e r 1 or U s e r 2 of P i c t u r e M o d e.
Press the button and then / button to select X D C o n t r a s t , X D C o l o u r or X D N R. Press the button and then / button to select O f f, L o w or H i g h. Select O f f, L o w, H i g h or A d a p t i v e (Only X D N R).

Auto Manual

Manual XD Contrast XD Contrast XD Colour XD NR

Off Low High

X D C o n t r a s t : Optimises the contract automatically according to the brightness of the reflection. A X D C o l o u r : Adjusts the colour of the reflection automatically to reproduce as close as possible to natural colours. A X D N R : Removes interference up to the point where it does not damage the original picture.

ADVANCED - GAMMA

Inversion This function inverts the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
Press the M E N U button and then select the O p t i o n menu.
Press the button and then I S M M e t h o d.
Language Country SIMPLINK Key Lock ISM Method ISM Method Power Saving Set ID Factory Reset
Normal White Wash Orbiter Inversion
Press the button and then / button to select either N o r m a l, W h i t e W a s h, O r b i t e r or I n v e r s i o n. If you do not need this function, set N o r m a l.
POWER SAVING PICTURE MODE
This function allows you to reduce the power consumption of the TV.
Press the button and then P o w e r S a v i n g.
Press the button and then your desired source.
Level Level Level Level Level

O n l y P C 5* * *

! NOTE (Except for 32PC5***)
The default factory setting complies with the E n e r g y s t a r requirements and is adjusted to the comfortable level to be viewed at home. You can increase the brightness of your screen by adjusting the P o w e r S a v i n g L e v e l or by setting the P i c t u r e M o d e.

FACTORY RESET

Use to quickly reset all the menu options to their original factory preset values. This function deletes all TV programmes.
Press the M E N U button and then select the O p t i o n menu. Press the button and then F a c t o r y R e s e t. Press the button and then Y e s or N o. /

To set

Factory Reset Yes No

F G OK RETURN

AUTO VOLUME LEVELER
Auto Volume automatically remains on the same level of volume if you change programmes.
Press the M E N U button and then the A u d i o menu.
Sound Mode Auto Volume Balance TV Speaker
Press the button and then A u t o V o l u m e.
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; SRS TSXT, Clear Voice, Standard, Music, Cinema, Sport or Game and you can also adjust the frequency of the equalizer. Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content. S R S T S X T, C l e a r V o i c e, S t a n d a r d, M u s i c, C i n e m a, S p o r t and G a m e are preset for optimum sound quality at the factory and are not adjustable.
Press the button and then S o u n d M o d e.
Press the button and then / button to select S R S T S X T, C l e a r V o i c e, S t a n d a r d, M u s i c, C i n e m a, S p o r t , G a m e or U s e r.
SRS TSXT Clear Voice Standard Music Cinema Sport Game User
SOUND SETTING ADJUSTMENT -USER MODE
Adjusting the audio equalizer.
button to select U s e r.
Select a frequency band by pressing the Set the desired sound level with the /

/ button. button.

0.1 0.5 1.5 5.kHz

BALANCE

You can adjust the sound balance of the speakers to the preferred levels.

Press the B a l a n c e.

Press the button and then desired adjustment.

button to make

Audio Sound Mode Auto Volume Balance Balance TV Speaker

R15 G 0

TV SPEAKERS ON/OFF SETUP
You can adjust the internal speaker status. In TV, AV, COMPONENT, RGB[PC] and HDMI mode, internal speaker audio can be operational even though there is no video signal. If you wish to use an external hi-fi system, turn off the TV internal speakers.

S p e a k e r.

button to select T V
Press the button and then O n or O f f.

Stereo/Dual Reception

When a programme is selected, the sound information for the station appears with the programme number and station name.
Press the Q. M E N U button and then select the M u l t i A u d i o menu.
button to select the sound output.
Broadcast Mono Stereo Dual

On Screen Display

MONO STEREO DUAL I, DUAL II, DUAL I+II
Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. To switch back to stereo. Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II.

DUAL I DUAL II DUAL I+II

Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker.

NICAM Reception

If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of broadcast received.
When NICAM mono is received, you can select N I C A M M O N O or F M M O N O.
When NICAM stereo is received, you can select N I C A M S T E R E O or F M M O N O. If the stereo signal is weak, switch to F M M O N O.
When NICAM dual is received, you can select N I C A M D U A L I, N I C A M D U A L I I or N I C A M D U A L I + I I or F M M O N O.
Speaker Sound Output Selection
In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers. Select the sound output.
L + R : Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is sent to the right loudspeaker. L + L : Audio signal from audio L input is sent to left and right loudspeakers. R + R : Audio signal from audio R input is sent to left and right loudspeakers.

ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
Installation guide menu appears on TV screen when it is turned on for the first time.
Press the / / button and then, O K but/ ton to select your desired language. Press the / / / to select your country. button and then, O K button
* If you want to change Language/ Country selection
Press the M E N U button and then use to select the O P T I O N menu.

button

Press the button and then use / button to select L a n g u a g e. Or, Press the button and then use / button to select C o u n t r y. Press the button and then use / / / button to select your desired language or country. The menus can be shown on the screen in the selected language. Press the O K button. Press the M E N U button to return to normal TV viewing. Press the R E T U R N button to move to the previous menu screen.
If you dont finish set up I n s t a l l a t i o n G u i d e by pressing R E T U R N button or time out of OSD (On Screen Display) display, it will continuously appear until completing set up whenever the set is turned on. If you select wrong local country, the teletext may not appear correctly on the screen and some problem may happen during teletext operation.

CLOCK SETUP

You must set the time correctly before using on/off timer function. If current time setting is erased by a power failure or the TV is unplugged, reset the clock.
Press the M E N U button and then the T i m e menu.
Clock Off Time On Time Sleep Timer Auto Sleep

Press the C l o c k.

button to set the hour.

-- : --

Press the minute.

button to set the

AUTO ON/OFF TIMER SETTING
The Off time function automatically switches the TV to standby at a preset time. Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. Once the on time/off time is set, these functions operate daily at the preset time. The Off time function overrides the On timer function if both are set to the same time. The TV must be in standby mode for the On timer to work.
Press the button and then / button to select O n/O f f T i m e. O O To cancel O n/O f f T i m e function, select O f f.

Press the minutes.

-- : -Off
For On Time function only P r o g r a m m e: Press the button and then ton to select the programme. V o l u m e: Press the button and then / adjust volume level at switch-on.

07:00 PR Vol. On

SLEEP TIMER SETTING
You do not have to remember to switch the TV off before you go to sleep. The sleep timer automatically switches the TV to standby after the preset time has elapsed.

Press the button and then S l e e p T i m e r.
When you switch the TV off, the TV releases the preset sleep time.

AUTO SHUT-OFF SETTING

If the TV set is switched on and there is no input signal, it will switch off automatically after 10 minutes.

Press the S l e e p.

This feature is not available in all countries. Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.

SWITCH ON/OFF

Press the T E X T button to switch to teletext. The initial page or last page viewed appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the T E X T or R E T U R N button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

Page selection
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. ( o r P + / - o r P R + / - ) button can be used to select the preceding or following page. The P /

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group. ( o r P + o r P R + ) button can be used. Alternatively the P ( o r P - o r P R - ) button can be used. The red button return to the previous selection. Alternatively the P

Dimensions

(Width x Height x Depth)

with stand without stand

1040 x 729 x 308 mm 40.9x 28.7 x 12.1 inches 1040 x 677 x 83.6 mm 40.9x 26.6 x 3.3 inches 26 kg / 57 lbs.kg / 52.9 lbs AC100-240V~ 50/60Hz 310W

Weight

Power requirement Power Consumption MODELS

50PG1***

50PG100R-ZA

50PG2***

50PG200R-ZA 1224.7 x 849 x 364 mm 48.2 x 33.4x 14.3inches 1224.7 x 790 x 86 mm 48.2x 31.1 x 3.4 inches 41.8 kg / 92.2 lbs 37.8kg / 83.3lbs AC100-240V~ 50/60Hz 420W
with stand without stand with stand without stand
1224.7 x 849 x 364 mm 48.2 x 33.4x 14.3inches 1224.7 x 790 x 83.6 mm 48.2x 31.1 x 3.2 inches 41.5 kg / 91.5 lbs 38.1kg / 84lbs AC100-240V~ 50/60Hz 420W

32PC5*

32PC53-ZB 32PC54-ZD 819.9 x 599.8x 258.4 mm 32.3 x 23.6 x 10.2 inches 819.9 x 554.2 x 78.1 mm 32.3 x 21.8 x 3.1 inches 16.2kg / 35.7 lbs 15.1kg / 33.2 lbs AC100-240V~ 50/60Hz 200W
Power requirement Power Consumption Television System Program Coverage External Antenna Impedance Operating Temperature Environment condition Operating Humidity Storage Temperature Storage Humidity
PAL/SECAM B/G/D/K, PAL I/II VHF: NZ1~E21, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S0 ~ 40C / 32 ~ 104F Less than 80% -20 ~ 60C / -4 ~ 140F Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.

APPENDIX IR CODES

1. How to Connect
Connect your wired remote control to the Remote Control port on the TV.
2. Remote Control IR Codes

Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz
Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3

Configuration of frame

1st frame
Lead code Low custom code High custom code Data code Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat frame

Repeat code

Lead code

9 ms 4.5 ms

0.55 ms

2.25 ms

Bit description Bit 0

0.56 ms 1.12 ms

0.56 ms 2.24 ms

Frame interval: Tf The waveform is transmitted as long as a key is depressed.

Tf Tf Tf=108ms @455KHz

Code (Hexa)

79 0B 5B 03 00

Function

INPUT POWER MENU RETURN

R/C Button R/C Button R/C Button (Power On/Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button

1E 1A 20 7E B1 B0 BA 8F 8E 45 BD
(or P - or PR-) R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
AV MODE MUTE LIST FAV Q.VIEW TEXT SIMPLINK

A Stop/TIME G Play/SIZE

10 ~ 19 Number Key 0 ~ 9 R/C Button
(or F) (or G) (or D) (or E)
OK( ) RED GREEN YELLOW BLUE

l l Pause

UPDATE

FF Rew/INDEX GG FF/HOLD

+(or VOL+) R/C Button - (or VOL-) R/C Button P
(or P + or PR+) R/C Button
(Record)/REVEAL R/C Button

R/C Button

EXTERNAL CONTROL THROUGH RS-232C
Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the TVs functions externally. Connect the serial port of the control device to the RS-232C jack on the TV back panel.RS-232C connection cables are not supplied with the TV.

RS-232C Setup

DVI IN

HDMI IN RS-232C IN

(CONTROL)
Type of Connector; D-Sub 9-Pin Male
Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection

RS-232C Configurations

7-Wire Configurations (Standard RS-232C cable) PC RXD TXD GND DTR DSR RTS CTS 8 D-Sub 9 TV 7 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS 3-Wire Configurations(Not standard) PC 8 D-Sub 9 TV 8 D-Sub 9 TXD RXD GND DTR DSR RTS CTS

Set ID

- Use this function to specify a set ID number. - Refer to Real Data Mapping 1. See page 93.
Press the M E N U button and then use select the O p t i o n menu. Press the S e t I D. button and then use /
Option Language Country SIMPLINK Key Lock ISM Method Power Saving Set ID Set ID Factory Reset
Press the button and then use / button to adjust S e t I D to choose the desired TV ID number. The adjustment range of SET ID is 1~ 99.

Communication Parameters

Baud rate : 9600 bps (UART) A Data length : 8 bits A Parity : None
Stop bit : 1 bit A Communication code : ASCII code A Use a crossed (reverse) cable.

Command Reference List

COMMAND1 COMMAND2 DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal)
01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control 06. Contrast 07 Brightness. 08. Colour 09. Tint 10. Sharpness 1 OSD Select 1. 12. Remote Control Lock /Key Lock Mode 13. Balance
k k k k k k k k k k k k k
a c d e f g h i j k l m t
00 ~ 01 Refer to p.~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 64
14. Colour Temperature 15. Red Adjustment 16. Green Adjustment 17 Blue Adjustment. 18. Abnormal Status 19. ISM Method 20. Power Saving 21. Auto Configure 22. Equalize 23. Tune Command 24. Channel Skip 25. Key 26. Input select (Main)