The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product
MFL34797007en-simp 9/8/08 3:15 PM Page 3

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Never touch this apparatus or antenna during a thunder or lighting storm. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
MFL34797007en-simp 9/8/08 3:15 PM Page 4
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70
Ground Clamp Antenna Lead in Wire
WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Antenna Discharge Unit (NEC Section 810-20) Grounding Conductors (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H)
Electric Service Equipment
NEC: National Electrical Code
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).

Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power Supply Short-circuit Breaker
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. Keep the product away from direct sunlight.
On Disposal (Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
MFL34797007en-simp 9/8/08 3:15 PM Page 5
WARNING / CAUTION. 2 SAFETY INSTRUCTIONS. 3 PREPARATION
Accessories. 6 Front Panel Information.7 Back Panel Information. Stand Installation. 1 Remote Control Functions. 12 Back Cover for Wire Arrangement. 14 Protection Cover. 16 Attaching the TV to a Wall. 17 Swivel Stand. 17 Attaching the TV to a desk. VESA Wall Mounting. 19 Desktop Pedestal Installation. 19 Antenna or Cable Connection. 20

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup. 21 DVD Setup. 22 VCR Setup. 23 PC Setup. 24

WATCHING TV

Turning On the TV. 27 Channel Selection. 27 Volume Adjustment. 27 Channel Setup. 28 On-Screen Menus Selection. 29

APPENDIX

Troubleshooting. 32 Maintenance. 34 Product Specifications. 35

HOW TO USE THE OWNER'S MANUAL ON THE CD-ROM
To view the Owner's Manual on the CD-ROM, Adobe Acrobat Reader must be installed on your PC. The ACRORD" folder on the CD-ROM contains the installation programs for them. If you want to install those programs, Open the My Computer Open the LG Open the ACRORD double-click your language.
TO VIEW THE OWNER'S MANUAL ON THE CD-ROM
The Owner's Manual files are included in the supplied CD-ROM. Load the supplied CD-ROM into the CD-ROM drive of your PC. After a while, the web page of the CD-ROM will open automatically. (for Window only)
When you select your product, display the PDF file.
You can find the desired contents easily using the bookmark.
If the web page does not appear automatically, open the Owner's Manual file directly. Open the My computer Open the LG Open the index.htm file.
MFL34797007en-simp 9/8/08 3:15 PM Page 6

PREPARATION

ACCESSORIES
Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product. User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product. For further information, see the the Owner's Manual files supplied CD-ROM.
INP UT PO WE R MO MU LTI TV DE PIP EZ PIC PIP EZ SOU DV D CH ND
VC R PIP CH + PIP SW INPU AP T O PO W ER

RA TIO

EX IT CC ME NU
TV INP MU PIP EZ PIC PIP EZ SOU CH LTI UT

UT PO WE R

RAT IO P

VC R INP UT

MO TV DV D

EN TE R

TIME R

TURN ME

CH PAG E
VC R PIP CH + PIP SW INPU AP T INF O

NU INF O

CC ME NU

VO 2 L

TIM ER

LCD TV PLASMA TV

Owner's Manual

6MUTE 9

P A G E

FLAS HBK

FLASH BACK

1.5V 1.5V

http://www.lgusa.com www.lg.ca Copyright 2007 LGE, All Rights Reserved.
CHPIP CH+ PIP SWA P PIP SAP INPU T
Owners Manual, Setup & Operation Guide for Commercial Mode

CD Manual (Refer to p.5)

Remote Control, Batteries

LCD TV model only

Power Cord
* Slightly wipe stained spot on the exterior only with the polishing cloth for the product exterior if there is stain or fingerprint on surface of the exterior.

Option Extras

Polishing Cloth
This feature is not available for all models.
* Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration.
Protective Bracket and Bolt for Power Cord
(This feature is not available for all models.)

(Refer to P.14)

D-sub 15 pin Cable
Only 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C models x2 Cable Management (Refer to p.14) Cable Holder (Refer to p.14) 4-Bolts for stand Torx plus 1-Bolt for fixing the assembly Star head screw Cable Holder (Refer to p.1 1) 1) (Refer to p.14) 32/37LC5DC*, 32/37LC50C* (Refer to p.1

models only

Plasma TV models only
75 ohm Round Cable (Except 42PG60C/65C) Only 42PG65C model
D-sub 15 Pin Cable (Except 42PG60C/65C)
Cable Holder (Except 42PX8DC)
x4 Bolts for stand assembly (Refer to P.18)

Cable Management Clip

MFL34797007en-simp 9/8/08 3:15 PM Page 7

FRONT PANEL INFORMATION

Here shown may be somewhat different from your TV. If your product has a protection tape attached, remove the tape. And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).
32/37/42LC5DC*,32/37/42LC50C*, 42LB5DC, 42LB50C

CHANNEL Buttons

VOL OL
VOLUME Buttons ENTER Button MENU Button INPUT Button ON/OFF Button

ENTER MENU

Remote Control Sensor Power/Standby Indicator Illuminates red when the TV is in standby mode. Illuminates green when the TV is switched on.

32LX5DC*, 32LX50C*

ON/OFF
ON/OFF Button INPUT Button MENU Button ENTER Button VOLUME Buttons CHANNEL Buttons
MFL34797007en-simp 9/8/08 3:15 PM Page 8

42PG60C, 42PG65C

Remote Control Sensor POWER Button

S t a n d (Only 42PG65C model)
Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on.

ENTER VOL

INPUT Button 42PX8DC

MENU Button

ENTER Button

VOLUME (-,+) Buttons

CHANNEL (E, D) Buttons
This TVs stand is sold, separately.
ON/OFF Button INPUT Button MENU Button ENTER Button VOLUME Buttons Remote Control Sensor CHANNEL Buttons Power/Standby Indicator Illuminates red when the TV is in standby mode. Illuminates green when the TV is switched on.
MFL34797007en-simp 9/8/08 3:15 PM Page 9

BACK PANEL INFORMATION

Here shown may be somewhat different from your TV.

S-VIDEO

R AUDIO L/MONO VIDEO S-VIDEO

VIDEO L/MONO AUDIO R

AV IN 2

ANTENNA IN

42PX8DC M.P.I.

A O L/MONO AUDIO R

MFL34797007en-simp 9/8/08 3:15 PM Page 10
Here shown may be somewhat different from your TV. This part mainly use picture for the LCD TV models.

M.P.I.

HDMI/DVI IN 1(DVI) 2 DIGITAL AUDIO OUT (OPTICAL)

M.P.I. UPDATE RESET

SERVICE ONLY

DVI IN

VIDEO AUDIO

VIDEO L (MONO)

HDMI/DVI IN, HDMI IN Connect a HDMI (DVI) connection to either input. DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. M.P.I
AV (Audio/Video) IN Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. COMPONENT IN Connect a component video/audio device to these jacks. RJP INTERFACE Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. ANTENNA IN Connect over-the air signals to this jack.
RESET/UPDATE/REMOTE CONTROL OUT SERVICE ONLY RGB IN (PC) Connect the output from a PC. AUDIO IN (RGB, DVI) Connect the audio from a PC or DTV. SPEAKER OUT 8

AV IN 1

REMOTE CONTROL OUT RGB IN

RJP INTERFACE

(MONO)

COMPONENT IN

SPEAKER AUDIO IN OUT (RGB, DVI) 8
DIGITAL AUDIO OUT OPTICAL

Hold the CABLE MANAGEMENT with both hands and pull it backward.
MFL34797007en-simp 9/8/08 3:15 PM Page 15
To separate the CABLE HOLDER, loosen the bolt installed the set.

BOLT CABLE HOLDER

MFL34797007en-simp 9/8/08 3:15 PM Page 16

42PX8DC

Hold the CABLE MANAGEMENT with both hands and pull it as shown.
Connect the cables as necessary. To connect additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Connect the cables as necessary. To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section. Install the CABLE MANAGEMENT CLIP as shown. (Except 42PG60C model) If your TV has CABLE HOLDER, fix it as shown and bundle the cables.

CABLE MANAGEMENT CLIP

How to remove the CABLE MANAGEMENT CLIP

(Except 42PG60C model)

First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward.

! NOTE

Do not hold the CABLE MANAGEMENT CLIP when moving the TV. - If the TV is dropped, you may be injured or the product may be broken.
MFL34797007en-simp 9/8/08 3:15 PM Page 17
ATTACHING THE TV TO A WALL
This feature is not available for all models. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV.
Insert the TV brackets (or eye-bolts) and bolts to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

SWIVEL STAND

20 (37LC5DC1, 42LC5DC, 42LC50C, 90 (32LX5DC/S, 32LX50C/S,
42PX8DC, 42LB5DC, 42LB50C, 42PG65C models) 32LC5DC/S,
32LC50C/S, 37LC5DC, 37LC50C models)
The TV can be conveniently swivelled on its stand 20or 90 to the left or right to provide the optimum viewing angle.

MFL34797007en-simp 9/8/08 3:15 PM Page 18
ATTACHING THE TV TO A DESK
Here shown may be somewhat different from your TV. The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. 1 * S c r e w s - M 5 x L ( t a b l e d e p t h + 8~m m ) ex) table depth-15mm: Bolts - M5 x 25
32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C

Stand 4-Screws

4-Screws

2-Screws Desk

42PG65C

WARNING

This apparatus must be securely attached to the floor/wall per installation instructions.Tipping, shaking, or rocking the television may cause injury/death.
MFL34797007en-simp 9/8/08 3:15 PM Page 19

VESA WALL MOUNTING

This product accepts a VESA-compliant mounting interface pad. (optional) There 4 threaded holes are available for attaching the bracket.

Product

Model 32LC5DC*, 32LC50C*, 32LX5DC*, 32LX50C*
VESA (A * B) 200 * * * * 400

LCD TV

32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C 42PG60C

PLASMA TV 42PX8DC

Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide.
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4inches on each side from the wall.
Image shown may differ from your TV.
4 inches 4 inches 4 inches 4 inches
Ensure adequate ventilation by following the clearance recommendations.
MFL34797007en-simp 9/8/08 3:15 PM Page 20
ANTENNA OR CABLE CONNECTION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments (Connect to wall antenna socket)

ANTENNA IN M.P.I.

Wall Antenna Socket
Outdoor Antenna (VHF, UHF)
RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)
Copper Wire Be careful not to bend the bronze wire when connecting the antenna.

2. Cable

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

3. Using both cable and antenna

Antenna

RF Coaxial Wire (75 ohm) Diplexer (Signal Combinner)

Signal Amplifier

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TVs, install a 2-Way Signal Splitter. If the antenna is not installed properly, contact your dealer for assistance.

AUDIO S-VIDEO

REMOTE CONTROL OUT R
Select A V 1 input source by using the I N P U T button on the remote control. If connected to A V I N 2, select A V 2 input source.

SPEAKE OUT 8

If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the set.
When connecting with an S-Video cable
Connect the S-VIDEO output of the VCR to the S - V I D E O input on the set. Connect the audio outputs of the VCR to the A U D I O input jacks on the set.

ENNA IN

GITAL AUDIO OUT PTICAL)

ENT IN

SPEAK OUT 8
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.
The picture quality is improved: compared to normal composite (RCA cable) input.
MFL34797007en-simp 9/8/08 3:15 PM Page 24

PC SETUP

When connecting D-sub 15pin cable

P.I. UPDATE

Connect the RGB output of the PC to the R G B I N jack on the set.
Connect the PC audio output to the A U D I O I N ( R G B , D V I ) jack on the set.

SPEAKER OUT 8

AUDIO IN (RGB, DVI)
Turn on the PC and the TV. Select R G B - P C input source by using the I N P U T button on the remote control.

RGB OUTPUT

When connecting HDMI to DVI cable
Connect the DVI output of the PC to the H D M I / D V I I N 1 ( D V I ) jack on the set. Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the set.
HDMI/DVI IN 1(DVI) 2 RGB IN OUT (OPTICAL

RVICE ONLY

Turn on the PC and the set Select H D M I 1 / D V I input source with using the I N P U T button on the remote control.

DVI-PC OUTPUT AUDIO

MFL34797007en-simp 9/8/08 3:15 PM Page 25
Supported Display Specifications (RGB/HDMI1-PC) Resolution 640x350 Horizontal Frequency(KHz) 31.469 31.469 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 47.700 47.720 47.130 Vertical Frequency(Hz) 70.08 59.94 72.80 75.00 56.25 60.31 72.18 75.00 60.00 70.06 75.02 60.00
Supported Display Specifications (HDMI2-DTV) Resolution 720x480 Horizontal Frequency(KHz) 31.500 31.469 44.960 45.000 33.720 33.750 Vertical Frequency(Hz)

60.00 59.94 59.94 60.00 59.94 60.00

640x480

1280x720

1920x1080

800x600
Supported Display Specifications (Y, CB /PB, CR /PR) Resolution Horizontal Frequency(KHz) 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 Vertical Frequency(Hz) 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00

1024x768

1280x768 1360x768 1366x768
720x480 59.799 59.658 1280x720 Supported Display Specifications (RGB/HDMI1-DTV) Resolution 720x480 Horizontal Frequency(KHz) Vertical Frequency(Hz) 1920x1080
31.50 60.00 31.47(HDMI1-DTV:31.469) 59.94 * RGB-DOS mode only: 640x350 44.96 45.00 33.72 33.75 59.94 60.00 * Except 42PG60C/65C models in HDMI1-PC mode. 59.94 60.00
MFL34797007en-simp 9/8/08 3:15 PM Page 26
* 42LB5DC, 42LB50C Supported Display Specifications (RGB/HDMI1-PC) Resolution 640x350

(RGB only)

Supported Display Specifications (HDMI2-DTV) Resolution 720x480 Horizontal Frequency(KHz) 31.500 31.469 44.960 45.000 33.720 33.750 67.500 Vertical Frequency(Hz) 60.00 59.94 59.94 60.00 59.94 60.00 60.00
Horizontal Frequency(KHz) 31.469 31.469 37.861 37.500 35.156 37.879 48.077 46.875 48.363 56.476 60.023 47.700 47.720 47.130 63.668 65.317 74.537 66.587 74.038
Vertical Frequency(Hz) 70.08 59.94 72.80 75.00 56.25 60.31 72.18 75.00 60.00 70.06 75.02 60.00 59.799 59.658 59.895 59.978 59.869 59.934 59.950
Supported Display Specifications (Y, CB /PB, CR /PR) Resolution Horizontal Frequency(KHz) 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 67.50 Vertical Frequency(Hz) 59.94 60.00 59.94 60.00 59.94 60.00 59.94 60.00 60.00
1280x768 1360x768 1366x768 1280x1024

720x480

1400x1050
1600x1200 1920x1080 1920x1200
* RGB-DOS mode only: 640x350
Supported Display Specifications (RGB/HDMI1-DTV) Resolution 720x480 Horizontal Frequency(KHz) Vertical Frequency(Hz)
31.50 60.00 31.47(HDMI1-DTV:31.469) 59.94 44.96 45.00 33.72 33.(HDMI1-DTV:67.5).43 59.94 60.00 59.94 60.00 59.94
MFL34797007en-simp 9/8/08 3:15 PM Page 27

TURNING ON THE TV

First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the (or O N / O F F) button on the TV or press the POWER button on the remote control. Select the viewing source by using the INPUT(or TV INPUT) button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

CHANNEL SELECTION

Press the CH ( + or - ) or C H ( a channel number. or ) or NUMBER buttons to select

VOLUME ADJUSTMENT

Adjust the volume to suit your personal preference.
Press the VOL ( + or -) button to adjust the volume. If you want to switch the sound off, press the M U T E button. You can cancel the Mute function by pressing the M U T E or VOL ( + or -) button.
MFL34797007en-simp 9/8/08 3:15 PM Page 28

CHANNEL SETUP

Auto Scan (EZ Scan)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run EZ Scan again after any Antenna/Cable connection changes. A password is required to gain access to EZ Scan menu if the Lock System is turned on.
Press the M E N U button and then use D or E or or button to select the S E T U P menu.
EZ Scan Manual Scan Channel Edit DTV Signal Channel Label
VIDEO AUDIO TIME OPTION SCREEN
button and then use Press the G or or button to select E Z S c a n.

or E or

Press the E N T E R button to begin the channel search. Allow E Z S c a n to complete the channel search cycle for A N T E N N A and C A B L E.
SETUP VIDEO AUDIO TIME OPTION SCREEN LOCK
Selection ( G or ) leads you to the EZ scan screen.

SETUP VIDEO

EZ Scan Manual Scan

Channel Edit

Processing EZ scan.

DTV Signal

OPTION SCREEN LOCK

Channel Label

Selection ( G or ) leads you to the EZ scan screen. ANALOG

Found Channel(s)

MENU Prev.
MFL34797007en-simp 9/8/08 3:15 PM Page 29
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Press the M E N U button and then use menu. Press the G or available menus.
button to select the each

button and then use D

button to display the
All available TV channels are searched and stored automatically. User can do manual channel selection and add or delete individual channels. You can add or delete in the channel list. Displays the DTV signal levels. Set a label to each channel.

EZ Picture

EZ Picture Color Temperature XD Advanced Reset
Selects the factory preset picture depend on the viewing environment: Daylight, Normal, Night Time, User1, User2. Choose one of three automatic color adjustments : Cool, Normal, Warm, User

Color Temperature

It is LG Electronics unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. Select Auto or Manual (XD Contrast, XD Color, XD NR, MPEG NR).

Advanced

Cinema Mode (On, Off) Set up the TV for the best picture appearance for viewing movies. Black Level (Low, High) Adjusting the contrast and the brightness of the screen using the black level of the screen.

Video Reset

Use to quickly reset all the Video menu options to their original factory preset values.
MFL34797007en-simp 9/8/08 3:15 PM Page 30

Audio Language

Audio Language EZ SoundRite EZ Sound Balance TV Speakers 0
You can available other language if a digital signal is provided by the broadcasting station. Automatically keeps on an equal volume level even if you change channel. Selects the factory preset sound for type of program. :Normal, Stadium, News, Music, Theater, and User Adjust the left/right sound of speaker. Turn the TV speaker On or off.
EZ SoundRite EZ Sound Balance TV Speakers

Auto Clock Manual Clock

Auto Clock

Off Timer

On Timer
The time is set automatically from a digital channel signal. Select your viewing area time zone. Select Auto, Off, On depending on whether or not your viewing area observes Daylight Saving time.

Auto Off

Manual Clock Off Timer On Timer Sleep Timer
Set the clock manually. Select On or Off. Select On or Off. Select the amount of time before your TV turns off automatically: Off, 10, 20,30, 60, 90, 120, 180, 240.

OPTION

Aspect Ratio
Aspect Ratio Caption/Text Caption Options Language ISM Method Low Power Set ID
Select the desired picture format. : Set by program, 4:3, 16:9, Horizon, Zoom1, Zoom2. Select a caption mode for displaying captioning information : Off, CC1 ~ 4, Text 1 ~ 4. Customize the DTV/CADTV captions that appear on your screen. Select your desired language for on screen menus : English, Spanish, French. Use it to minimize any fixed image on the screen. : Normal, White Wash, Orbiter, Inversion. Reduces the plasma display power consumption. Choose the desired TV ID number.
Caption/Text Caption Option Language

Only 42PX8DC model

ISM Method Low Power Set ID
MFL34797007en-simp 9/8/08 3:15 PM Page 31

SCREEN

Auto config. Manual config. XGA Mode Reset
Auto config Manual config XGA Mode Reset
Automatically adjusts picture position and minimizes image shaking. Adjusts screen manually. : Phase, Clock, H-Position, and V-Position Selematch the resolution of RGB mode and selection of XGA mode. To initialize the adjusted value.

For USA

Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Aux. Block Downloadable Rating
Lock System Set Password Block Channel Movie Rating TV Rating-Children
Select On or Off. Change the password. Select a channel number that you wish to block. Blocks movies according to the movie ratings limits specified. Prevents children from watching certain children's TV programs, according to the ratings limit set. Based on the ratings, blocks certain TV programs that you and your family do not want to view. Selecting canadian english language rating system. Selecting canadian french language rating system. Enables you to select a source to block from the external source devices you have hooked up. This function may become available in the future and will be available only for digital channel signal.

For Canada

Lock System Set Password Block Channel TV Rating-English TV Rating-French Aux. Block Downloadable Rating
TV Rating-General TV Rating-English TV Rating-French Aux. Block Downloadable Rating
MFL34797007en-simp 9/8/08 3:15 PM Page 32

TROUBLESHOOTING

The operation does not work normally.
The remote control doesnt work
Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. Ensure that the batteries are installed with correct polarity (+ to +, - to -). Ensure that the correct remote operating mode is set: TV, VCR etc. Install new batteries. Is the sleep timer set? Check the power control settings. Power interrupted. No broadcast on station tuned with Auto off activated.
Power is suddenly turned off
The video function does not work. Check whether the product is turned on. Try another channel. The problem may be with the broadcast. Is the power cord inserted into wall power outlet? Check your antenna direction and/or location. Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in.

No picture &No sound

Picture appears slowly after switching on
This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes.