PCMCIA CARD SLOT

HDMI IN 3

COMPONENT IN

AUDIO IN OPTICAL DIGITAL (RGB/DVI) AUDIO OUT

VIDEO L/MONO AUDIO R

S-VIDEO

HDMI/DVI IN 2

RGB IN (PC)
1(DVI) RS-232C IN (CONTROL & SERVICE)

AV IN 3

ANTENNA IN
Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. AUDIO IN (RGB/DVI) Connect the audio from a PC.
OPTICAL DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks.
HDMI IN 1/2/3 Connect a HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable. RGB IN (PC) Connect the output from a PC.

STAND INSTALLATION

(Only 32/37/42LG35**, 32/37/42LG5***, 32/37/42LG75**)
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Assemble the parts of the s t a n d b o d y with c o v e r b a s e of the TV.
Fix the 4 bolts securely using the holes in the back of the TV.

Stand Body

Cover Base

Swivel Stand

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
You should purchase necessary components to fix the TV to the wall on the market. Position the TV close to the wall to avoid the possibility of it falling when pushed. The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen these bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.

It is not possible to use ISM Method and Low power in LCD TV models. It is possible to use Power Indicator in LCD TV models only.
Press the MENU button and then select the OPTION menu.
Press the G button and then D or E button to select Factory Mode.
SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTION G SIMPLINK SCREENO Power Indicator Factory Mode
Press the G button and then D or E button to select Factory Reset.
Language Country Lock System Parental Control Input Label SIMPLINK Power Indicator Factory Mode Set ID 1 Factory Reset OK ISM Method Normal

Press the OK button.

The message If you enter a password, all user setting will be reset will appear.

Low Power Off

Use NUMBER buttons to input a 4-digit password.
Language Country Lock System Parental Control Input Label SIMPLINK Power Indicator Factory Mode
Set ID 1 Factory Reset OK ISM Method Normal Low Power Off
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
INPUT D/A TV/RADIO INPUT BRIGHT VCR SIMPLINK TEXT RATIO I/II MODE TV DVD
POWER Switches the TV on from standby or off to standby. D/A INPUT Selects digital or analogue mode. Switches the TV on from standby. TV/RADIO Selects Radio or TV channel in digital mode.
INPUT External input mode rotate in regular sequence. Switches the TV on from standby. Brightness Adjusts screen brightness. adjustment This returns to the default settings brightness by changing mode source.
Coloured These buttons are used for teletext (on TELETEXT buttons models only) or P r o g r a m m e e d i t.
EXIT Clears all on-screen displays and returns to TV viewing from any menu. BACK Allows the user to move back one step in an interactive application, EPG or other user interaction function.
MENU Selects a menu. INFO i Shows the present screen information.

9 Q.VIEW

GUIDE Shows programme schedule.
VOLUME UP Adjusts the volume. /DOWN FAV Displays the selected favourite programme. MUTE Switches the sound on or off.

UPDATE SLEEP SUBTITLE

INDEX HOLD

REVEAL

Programme Selects a programme. UP/DOWN 0~9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme table. Q.VIEW Returns to the previously viewed programme.

INPUT D/A TV/RADIO INPUT

MODE TV DVD
MODE Selects the remote operating modes. See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen. (G p.51)

BRIGHT VCR

SIMPLINK TEXT
TELETEXT These buttons are used for teletext. BUTTONS For further details, see the Teletext section. RATIO Selects your desired picture format. I/II Selects the sound output.
VCR/DVD Controls some video cassette recorders or DVD players control buttons when you have already selected DVD or VCR mode button. Control connected AV devices by pressing the D or E or F or G, OK buttons and buttons for play, stop, pause, fast reverse, fast forward, chapter skip. (The button does not provide such functions.) THUMBSTICK Allows you to navigate the on-screen menus and adjust (Up/Down/Left the system settings to your preference. Right)

If you wish to continue manual tuning, select YES using the F or G button.
Then, press OK. Otherwise select NO.

Search

PROGRAMME EDIT (IN DIGITAL MODE)
When a programme number is skipped, it means that you will be unable to select it using PR + or - button during TV viewing. If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the Programme edit menu
This function enables you to skip the stored programmes.
Press the G button and then D or E button to select Programme Edit menu.
Press the G button to enter the Programme Edit menu. Use NUMBER buttons to input a 4-digit password in Lock System On.
Select a programme to be stored or skipped with the D or E or F or G button.
Press the BLUE button repeatedly to have the programme skipped or stored.
When programmes are to be skipped, skipped programme shows in blue and these programmes will not be selected by the PR + or - buttons during TV viewing.

Mini Glossary

Displayed when a DTV Programme. Displayed when a Locked Programme. Displayed when a Radio Programme.
Skipping a programme number
Select a programme number to be skipped with the D or E or F or G button. Press the BLUE button. The skipped programme number turns to blue. Press the BLUE button again to release the skipped programme. When a programme number is skipped it means that you will be unable to select it using the PR + or button during normal TV viewing. If you wish to select a skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or EPG.
Locking a programme (In Lock System On mode only) Select a programme to be locked with the D or E or F or G button. Press the GREEN button. The lock symbol will appear in front of that programme number. Press the GREEN button again to release this function.
Note : G To watch a locked programme, input a 4-digit password in Lock system. Be sure to remember this number! , , , G If you forget your password, press on the remote control handset. G If you select another programme after releasing a locked programme and then return to the locked programme within 1 minute, there is no need to input a password to select the locked programme.
Selecting favourite programme Select your favourite programme number by pressing D or E or F or G button and then press the FAV button on your remote control handset. This will automatically include the selected programme into your favourite programme list.

Back Select

CI [COMMON INTERFACE] INFORMATION (IN DIGITAL MODE ONLY)
This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services. When the module is inserted into the CI slot, you can access the module menu. To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CAM module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not have any sound output. This may be incompatible with the CI module and smart card.
Press the G button and then D or E button to select CI Information.
Press the G button and then OK button.
Press the D or E button to select the desired item: Module information, smart card information, language or software download etc.

Module

This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider. It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

Viaccess Module

Consultations Authorizations Module information

Select the item

AUTO PROGRAMME TUNING (IN ANALOGUE MODE)
All stations which can be received are stored by this method. It is recommended that you use Auto tuning during installation of this TV.
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Auto Tuning. Press the G button to select System. Select a TV system with the F or G button; L : SECAM L/L (France) BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
SETUP G Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit TIMEO OPTIONO SCREENO
Auto Tuning Manual Tuning Programme Edit
System Storage From Start
Press the E button to select Storage From. Select the initial programme number with the F or G button or NUMBER buttons on the Storage From menu.
Press the E button to select Start. The station name is stored for stations which broadcast VPS (Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number. To stop auto tuning, press the MENU button. When auto tuning is complete, the Programme Edit menu appears on the screen. See the Programme Edit section to edit the stored programme.
MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.

Storage System Band Channel Fine Search Name
PROGRAMME EDIT (IN ANALOGUE MODE)
This function enables you to delete or skip the stored programmes. You can also move some channels to other programme numbers or copy blank channel data into a selected programme number.
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Programme Edit. Press the G button to display the Programme Edit menu.
Deleting a programme Select a programme to be deleted with the D or E or or G button.
Press the RED button twice. The selected programme is deleted, all the following programmes are shifted up one position.

Copying a programme

Select a programme to be copied with the D or E or or G button.
Press the GREEN button. All the following programmes are shifted down one position.
SIMPLINK TEXT RATIO I/II FAV VOL PR
Moving a programme Select a programme to be moved with D or E or F or G button. Press the YELLOW button. Move the programme to the desired programme number with the D or E or F or G button. Press the YELLOW button again to release this function.

a b c d

Skipping a programme number Select a programme number to be skipped with D or E or F or G button. Press the BLUE button. The skipped programme number turns to blue. Press the BLUE button to release the skipped programme. When a programme number is skipped it means that you will be unable to select it using the PR + or button during normal TV viewing. If you wish to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu. Selecting a Favourite Programme Select your favourite programme number with D or E or F or G button. Press the FAV button. The selected programme will be added to the favourite programme list.
SELECTING THE PROGRAMME TABLE
You can check which programmes are stored in the memory by displaying the programme table.

DTV List

Displaying programme LIST Press the LIST button to display the PROGRAMME LIST menu. The programme list appears on the screen. You may find some blue programmes. These have been set up to be skipped by auto programming or in the programme edit mode. Some programmes with the channel number shown in the programme LIST indicate there is no station name assigned.
YLE TV1 YLE TV2 YLE FST YLE 24 YLE Teema TV4 TV4 Film TVTV4 Plus CNN
< In Digital Mode >

Programme List

Selecting a programme in the programme list Select a programme with the D or E button. Press the OK button. The TV switches to the chosen programme number.
BBC1 C 01 C 04 C 43 C 05 BLN 2 S 04 S 05 S 07 S 12
Paging through a programme list (Digital Mode Only) Press the PR + or - button repeatedly to turns the pages. Press the LIST button to return to normal TV viewing.

Favourite

Button Function in 8 Day Guide Mode
Remote Control Buttons RED GREEN YELLOW BLUE
Function Change EPG mode Enter Date setting mode Enter Timer Record/Remind setting mode Enter Timer Record/Remind list mode Change to the selected channel Select NOW or NEXT Programme Select the Broadcast Programme Page Up/Down Switch off EPG Select TV or RADIO Programme Detail information on or off
Button Function in Date Change Mode
Remote Control Buttons Function GREEN Switch off Date setting mode Change to the selected date Select a date F or G Switch off Date setting mode E GUIDE/EXIT Switch off EPG
6 BBC Channel Today G 14:30
This is BBC THREE BBC BBCi Racing BBC NEWS Racing News BBC THREE

Date Change Date Exit

Button Function in Extended Description Box
Remote Control Buttons D or E INFO i PR + or GUIDE/EXIT Function Text Up/Down The detail information on or off Page Up/Down Switch off EPG
Information Friends Mona The Vampire 14:00 15:20 Record 3 Apr 14 : Apr
Miss Gottos Haunted House/Cry Of the Swamp; Miss Gotto Wail Moves into a new house, and theres mysterious wail enanating from the local sweep Of The Swamp; Miss Gotto Wail Moves into a new house, and theres a mysterious wail enanating from the local sweep Of The Swamp; Miss Gotto Wail Moves into a new house, and theres a mysterious wail enanating from the local sweep Of The Swamp; Miss Gotto Wail Moves into a new house, and theres a mysterious wail enanating from the local sweep Of The Swamp

Info. Exit

Manual Record
Button Function in Record/Remind Setting Mode
- This function is available only when recording equipment that use pin8 recording signalling has been connected to the DTV-OUT terminal, using a SCART cable. Remote Control Buttons Function YELLOW Change to Guide mode Save Timer Record/Remind Select Type, Service, Date or Start/End time F or G Function setting D or E
Manual Record 14 : Apr Type

Programme 07 BBC THREE

Date 28 Feb

Start 22 : 35

End 23 : 00

Record

Cancel
Button Function in Timer List Mode
Remote Control Buttons YELLOW GREEN RED BLUE D or E Function Add new Manual Timer setting mode Enter Timer list editing mode Delete the selected item Change to Guide mode Select Timer list

Schedule List

1 BBC TWO 08:00 ~ 09:00 Fri 23 Feb

14 : Apr

Title Friends Newsnight review Road trip BBC News Carrott Gold Frineds
Programme 01 BBC TWO 02 BBC TWO 02 BBC TWO 07 BBC THREE 01 BBC ONE 01 BBC TWO
Date Wed 23 Feb Fri 25 Feb Sat 26 Feb Fri 25 Feb Mon 28 Feb Wed 28 Feb
Time 08:00 23:00 00:35 12:00 22:35 08:00

Delete

VCR SIMPLINK TEXT RATIO I/II
PICTURE SIZE (ASPECT RATIO) CONTROL
You can watch the screen in various picture formats; : 9, O r i g i n a l, 4 : 3, : 9, Z o o m 1 / 2 and J u s t S c a n (Only 32LG59**, 37/42/47/52LG55**, 32/37/42/47/52LG75**, 42LG75**, 50PG45**, 50PG75**). It is possible to use Just Scan in DTV mode only. If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible.

FAV BACK EXIT MENU INFO i GUIDE
You can adjust the enlarge proportion using D or E button.
Press the R A T I O button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the SCREEN menu.
16:9 The following selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire screen (useful for viewing 4:3 formatted DVDs).
Original When your TV receives a wide screen signal it will automatically change to the picture format broadcast.

Original 16:9

4:3 The following selection will allow you to view a picture with an original 4:3 aspect ration, grey bars will appear on both the left and right of the screen.
Zoom2 Choose Zoom 2 when you wish the picture to be altered, both horizontally extended and vertically cropped. The picture adopting a compromise between alteration and screen coverage.
14:9 You can view a picture format of 14:9 or a general TV programme in the 14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is magnified to the left and right.
Zoom1 The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped.
Just Scan (Only 32LG59**, 37/42/47/52LG55**, 32/37/42/47/52LG75**, 50PG45**, 50PG75**) Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image. Note: 1. If there are interference in original picture, you can view interference at the edge. 2. Specification is subject to change without prior notice.
You can only select Original, 14:9 in DTV, TV or AV mode. You can not select Zoom1/2 in RGB/HDMI[PC] mode only. In HDMI (1080i 50Hz/60Hz, 1080p 24Hz/50Hz/60Hz) mode, Just Scan (Only 32LG59**, 37/42/47/52LG55**, 32/37/42/47/52LG75**, 42LG75**, 50PG45**, 50PG75**) is available.

PRESET PICTURE SETTINGS

Picture Mode-Preset
Intelligent Sensor Adjusts picture according to the surrounding conditions. (32/37/42/47/52LG5***, 32/37/42/47/52LG75** only) Select this option to display a sharp image. The most general and natural screen display status. Select this option to display a cinema image. Select this option to use a user defined setting.

VOL BACK EXIT MENU INFO i GUIDE

Vivid Standard

Cinema User 1/2
Press the MENU button and then D or E button to select the PICTURE menu. Press the G button and then D or E button to select Picture Mode. Press the G button and then D or E button to select Intelligent Sensor (32/37/42/47/52LG5***, 32/37/42/47/52LG75** only), Vivid, Standard, Cinema, User 1 or User 2. Press the EXIT button to return to normal TV viewing. Picture Mode adjusts the TV for the best picture appearance. Select the preset value in the Picture Mode menu based on the programme category. Intelligent Sensor (32/37/42/47/52LG5***, 32/37/42/47/52LG75** only), Vivid, Standard and Cinema are programmed for optimum picture reproduction at the factory and cannot be changed.
SETUPO Picture Mode G Colour Temperature TIMEO Advanced Picture Reset Demo

AUDIOO OPTIONO SCREENO

Picture Mode Colour Temperature Advanced Picture Reset Demo
Intelligent Sensor Vivid Standard Cinema User 1 User 2
Auto Colour Tone Control (Warm/Medium/Cool)
To initialize values (reset to default settings), select the Cool option. Choose one of three automatic colour adjustments. Set to warm to enhance hotter colours such as red or set to cool to see less intense colours with more blue.
Its available to use this function in User mode.
Press the MENU button and then D or E button to select the PICTURE menu.
Press the G button and then D or E button to select Colour Temperature.
Press the G button and then D or E button to select either Cool, Medium, Warm or User.

Cool Medium Warm User

MANUAL PICTURE ADJUSTMENT

Picture Mode-User option

It is possible to use Back Light function in LCD TV models only.
Press the G button and then D or E button to select Picture Mode.
Press the G button and then 1 or User 2.

button to select User

Press the G button and then D or E button to select the desired picture option (Back Light, Contrast, Brightness, Colour, Sharpness and Tint).
Press the G button and then F or G button to make appropriate adjustments.

ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjusts the TV to best picture quality. This function works in the following mode: AV (NTSC-M), S-Video (NTSC-M) or HDMI. Press the MENU button and then D or E button to select the PICTURE menu.
Cinema Off Black Level Low
Press the G button and then D or E button to select Advanced. Press the G button and then D or E button to select Black Level. Press the F or G button to select Auto, Low or High.
Picture Mode Colour Temperature Advanced Picture Reset Demo Cinema

F G On

Black Level Low
L o w : The reflection of the screen gets darker. H i g h : The reflection of the screen gets brighter.
A Auto Realizing the Black Level of the screen and set it to High or Low automatically.

ADVANCED - TRUMOTION

(37/42/47/52LG75** only)
It is used for the best picture quality without any motion blur or judder when you enter a quick image or Film Source. This feature is disable in RGB-PC, HDMI-PC mode.
Advanced Picture Reset OPTIONO Demo SCREENO TruMotion Demo
Press the G button and then D or E button to select Advanced.
Press the G button and then D or E button to select TruMotion.
Picture Mode Colour Temperature Advanced Picture Reset Demo TruMotion Demo
Cinema Off Black Level Low TruMotion High
, Press the F or G button to select Off, Low or High.
Low : Provides smooth picture movement. Use this setting for standard use. High : Provides smoother picture movement. Off : Use this setting when High and Low setting result in noise.
Advanced Picture Reset Demo TruMotion Demo
Cinema Off Black Level Low TruMotion

F G High

If you enable TruMotion, noise may appear on the screen. If this occurs, set TruMotion to Off.

PICTURE RESET

Returns to the default factory setting for Picture Mode, Colour, Temperature, XD and Advanced.
Press the MENU button and then D or E button to select the PICTURE menu. Press the G button and then D or E button to select Picture Reset. Press the G button to initialize the adjusted value.

TRUMOTION DEMO

Use it to see the difference between TruMotion Demo on and TruMotion Demo off. Its not available to use this function in RGB/HDMI-PC mode.

Audio Language OSD Information Display N.A Status Not Available Audio for Visual Impaired Dolby Digital Audio HE-AAC Audio Dolby Digital Plus Audio
Subtitle Language OSD Information Display N.A
Status Not Available Teletext Subtitle Subtitle for Hard of Hearing
- The audio/subtitles can be displayed in a simpler form with 1 to 3 characters broadcast by the service provider. - When you select supplementary Audio (Audio for Visual/Hearing Impaired) the TV may output a part of the Main audio.

CLOCK SETUP

The clock is set automatically when receiving a digital signal. (You can set the clock manually only if the TV has no DTV signal.) You must set the time correctly before using on/off timer function.
Press the MENU button and then select the TIME menu.

Press the Clock.

button and then
Press the G button and then F or G button to select either the year, date or time option.
Clock Off Time On Time Auto Sleep Time Zone
Once selected, use the D or E button to set the year, date, and time options.

Time Date Year

14 Apr 2007
AUTO ON/OFF TIMER SETTING
The Off time function automatically switches the TV to standby at a preset time. Two hours after the TV is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. Once the on time/off time is set, these functions operate daily at the preset time. The Off time function overrides the On timer function if both are set to the same time. The TV must be in standby mode for the On timer to work.
Press the G button and then D or E button to select Off Time/On Time. Press the G button and then D or E button to select On. To cancel On/Off Time function, select Off.
Press the G button and then D or E button to set the hour. Press the G button and then D or E button to set the minutes. For On Time function only Programme: Press the G button and then D or E button to select TV, DTV or Radio in the Mode menu. And then, Press the G button and then D or E button to select the programme. Volume: Press the G button and then D or E button to adjust volume level at switch-on.

Volume Mode PR

AUTO SHUT-OFF SETTING
If the TV is switched on and there is no input signal, it will switch off automatically after 10 minutes.

Note R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON (POWER ON/OFF) R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON R/C BUTTON

II IFF GGI

FF GG A O
EXTERNAL CONTROL DEVICE SETUP

RS-232C Setup

Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the TVs functions externally. Connect the serial port of the control device to the RS-232C jack on the TV back panel. Note: RS-232C connection cables are not supplied with the TV.
Type of Connector; D-Sub 9-Pin Male
No. 9 Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection

RS-232C Configurations

7-Wire Configurations (Standard RS-232C cable) PC RXD TXD GND DTR DSR RTS CTS 8 D-Sub 9 TV 7 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS 3-Wire Configurations(Not standard) PC 8 D-Sub 9 TV 8 D-Sub 9 TXD RXD GND DTR DSR RTS CTS

BACK MENU INFO i GUIDE

Set ID
Use this function to specify a set ID number. Refer to Real Data Mapping. G p.102 It is not possible to use ISM Method and Low power in LCD TV models. It is possible to use Power Indicator in LCD TV models only.

1 APPENDIX

Press the G button and then D or E button to select Set ID.
Press the F or G button to adjust Set ID to choose the desired TV ID number. The adjustment range of SET ID is 1~ 99.
Factory Reset ISM Method Normal Low Power Off

Communication Parameters

Baud rate : 9600 bps (UART) A Data length : 8 bits A Parity : None
Stop bit : 1 bit A Communication code : ASCII code A Use a crossed (reverse) cable.

Command Reference List

COMMAND COMMAND DATA (Hexadecimal) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control 06. Contrast 07 Brightness. 08. Colour 09. Tint 10. Sharpness 1 OSD Select 1. 1 Remote control lock mode 2. 1 Balance 3. 1 Colour Temperature 4. 1 Red Adjustment 5. 1 Green Adjustment 6. 1. Blue Adjustment Abnormal Status 8. 19. ISM Method 20. Low Power 21. Auto Configure 22. Channel Select Command 23. Send IR Code 24. Back Light 25. Input select (Main) k k k k k k k k k k k k k k k k k k j j j m m m x a c d e f g h i j k l m t u v w $ z p q u a c g b 00 ~ 01 Refer to p. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ a Refer to p. ~ Refer to p. 103 Key Code 0 ~ 64 Refer to p. 103

02. Aspect Ratio (Command: k c) (Main Picture Size)
G To adjust the screen format. (Main picture format)
You can also adjust the screen format using the RATIO button on remote control or in the SCREEN menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 01 : 02 : 03 : 04 : 05 : Normal screen (4:3) Wide screen (1 6:9) Zoom1 Zoom2 Original 06 : 14:: Just Scan
(Only 37/42/47/52LG5***, 32/37/42/47/52LG75**, 42LG75**, 50PG45**, 50PG75**)
06. Contrast (Command: k g)
G To adjust screen contrast.
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to Real data mapping 1. See page 102. Ack [g][ ][Set ID][ ][OK][Data][x]
[c][ ][Set ID][ ][OK][Data][x] * Using the PC input, you select either 16:9 or 4:3 screen aspect ratio. 03. Screen Mute (Command: k d)
G To select screen mute on/off.
[k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture on) 01 : Screen mute on (Picture off)
07. Brightness (Command: k h) G To adjust screen brightness. You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to Real data mapping 1. See page 102. Ack [h][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
08. Colour (Command: k i)
G To adjust the screen colour.
1 2. Remote control lock mode ( C o m m a n d : k m )
G To lock the front panel controls on the TV and remote
You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to Real data mapping 1. See page 102. Ack [i][ ][Set ID][ ][OK][Data][x]
control. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 00 : Lock off Ack 01 : Lock on
[m][ ][Set ID][ ][OK][Data][x] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released.
09. Tint (Command: k j) G To adjust the screen tint. You can also adjust tint in the PICTURE menu.
13. Balance (Command: k t)

G To adjust balance.

[k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 ~ Green : 64 * Refer to Real data mapping 1. See page 102. Ack [j][ ][Set ID][ ][OK][Data][x]
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to Real data mapping 1. See page 102. Ack [t][ ][Set ID][ ][OK][Data][x]
10. Sharpness (Command: k k) G To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 * Refer to Real data mapping 1. See page 102. Ack [k][ ][Set ID][ ][OK][Data][x]
14. Colour Temperature (Command: k u)
G To adjust colour temperature. You can also adjust Colour