SWIVEL STAND

(Only PLASMA TV MODELS)
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit your viewing position.

! NOTE

G Before adjusting the angle, you must remove the cable management and loosen (to the left) the shaft bolt on the middle of stands back. And when stand be level with TV, you must close (to the right) the shaft bolt to set the hole.
LCD TV Models: 37LF6*, 42LF6*, 47LF6*, 52LF6*

PROGRAMME Buttons

OK MENU
OK Button MENU Button INPUT Button POWER Button
Intelligent Eye Adjusts picture according to the surrounding conditions.
Power/Standby Indicator illuminates red in standby mode. illuminates green when the set is switched on.
LCD TV Models: 37LY9*, 42LY9*, 47LY9*, 52LY9*
Intelligent Eye Adjusts picture according to the surrounding conditions. Remote Control Sensor

OK Button

MENU Button

INPUT Button

LCD TV Models: 37/42LF7*

PR VOL OK MENU INPUT

PROGRAM Buttons

BACK PANEL INFORMATION

This is a simplified representation of the back panel. Here shown may be somewhat different from your TV.

Plasma TV Models

AV IN 3 V

S-VIDEO

VIDEO L/MONO AUDIO R S-VIDEO

AV IN 3

L/MONO VIDEO L/ MONO AUDIO R
S-Video Input Connect S-Video out from an S-VIDEO device. Audio/Video Input Connect audio/video output from an external device to these jacks.

PCMCIA CARD SLOT

HDMI/DVI IN 1

HDMI IN 2

RGB IN

RGB (PC) AUDIO (RGB/DVI)

AV 1 V

AV 2 V

ANTENNA IN

DIGITAL AUDIO OUT

COMPONENT IN

OPTICAL

RS-232C IN (CONTROL & SERVICE)
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable.
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. Component Input Connect a component video/audio device to these jacks.
RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port.
Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
Antenna Input Connect over-the-air signals to this jack. DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.

VIDEO L/MONO AUDIO R

LCD TV Models (Except 37/42LF7*)
EJECT HDMI/DVI IN 1 HDMI IN 2 RGB IN
RGB(PC) AUDIO IN (RGB/DVI)

HDMI IN 3

EJECT HDMI/DVI IN 1
S-Video Input Connect S-Video out from an SVIDEO device. Audio/Video Input Connect audio/video output from an external device to these jacks.
RS-232C IN (CONTROL & SERVICE) ANTENNA IN

RGB(PC)

AUDIO IN (RGB/DVI)
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable. RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port. Antenna Input Connect over-the-air signals to this jack. DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work.
RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. Component Input Connect a component video/audio device to these jacks. Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
LCD TV Models : 37/42LF7*

AV IN 2

Audio/Video Input Connect audio/video output from an external device to these jacks.

MI/DVI IN 1

RS-232C IN

ENNA N

VIDEO AUDIO
PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) HDMI Input Connect a HDMI signal to HDMI IN. Or DVI(VIDEO)signal to HDMI/DVI port with DVI to HDMI cable. DIGITAL AUDIO OUT OPTICAL Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. Antenna Input Connect over-the-air signals to this jack. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.
Component Input Connect a component video/audio device to these jacks. RGB/DVI Audio Input Connect the monitor output from a PC to the appropriate input port. Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
S-Video Input S-VIDEO Connect S-Video out from an SVIDEO device.

USB IN

L/MONO AUDIO R
STAND INSTALLATION (Only 37 inch LCD TV Models)

Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage.
Assemble the product stand with the product as shown.
Install the 4 bolts securely, in the back of the product in the holes provided.
ATTACHING THE TV TO A DESK (Only 37LF7*)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw.

1-screw Stand

! WARNING
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
ATTACHING THE TV TO A WALL
Set it up close to the wall so the product doesnt fall over when it is pushed backwards. The instructions shown below is a safer way to set up the product, which is to fix it on the wall so the product doesnt fall over when it is pulled in the forward direction. It will prevent the product from falling for-ward and hurting people. It will also prevent the product from damage caused by fall. Please make sure that children dont climb on or hang from the product.
Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
When moving the product to another place undo the ropes first. Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. To use the product safely make sure that the height of the bracket that is mounted on the wall is same as that of the product.

BACK COVER FOR WIRE ARRANGEMENT

Plasma TV models

Hold the CABLE MANAGEMENT with both hands and pull it as shown.

CABLE MANAGEMENT

Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section.
Reinstall the CABLE MANAGEMENT as shown.
LCD TV models (Except 37/42LF7*)
Connect the cables as necessary. To connect an additional equipment, see the E x t e r n a l e q u i p m e n t C o n n e c t i o n s section.
Install the C A B L E M A N A G E M E N T as shown.
Bundle the cables using the supplied twister holder. (This feature is not available for all models.)
How to remove the cable management
Hold the C A B L E M A N A G E M E N T with both hands and pull it upward.
Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.
LCD TV model (Only 37/42LF7*)
Install the C A B L E M A N A G E M E N T as shown. (Insert it as pushing the loops on the both sides of the cable management.)
Bundle the cables using the supplied twist holder. (This feature is not available for all models.)
Hold the C A B L E M A N A G E M E N T with both hands and pull it out. (Pull it out as holding the loops on the both sides of the cable management.)
G Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.
The set can be installed in various ways such as on a wall, or on a desktop etc. The set is designed to be mounted horizontally.

Power Supply

GROUNDING
Ensure that you connect the earth ground wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Short-circuit Breaker

DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4" on each side and from the wall.

4 inches

When not using the desk-type stand (60PF9* only ) Rubber cap When not using the desk-type stand, install the supplied rubber caps for protecting the desk-type stand fixture as shown at the figure.
WALL MOUNT: HORIZONTAL INSTALLATION
For proper ventilation, allow a clearance of 4" on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
4 inches 4 inches 4 inches 4 inches
If you want to install the desk-type stand fixture protection cover (Plasma T V m o d e l s only) To prevent the foreign materials from entering the desk-type stand fixture, fix the desk-type stand fixture protection cover by using the supplied bolts as shown at the figure. Desk-type stand fixture protection cover

When connecting with an S-Video cable

VIDEO S-VIDEO

ANT IN
Connect the S-VIDEO output of the DVD to the S V I D E O input on the set. Connect the audio outputs of the DVD to the A U D I O input jacks on the set. Turn on the DVD player, insert a DVD. Select AV3 input source with using the I N P U T button on the remote control.
L/MONO VIDEO L/ MONO AUDIO R S-VIDEO

OUTPUT SWITCH

ANT OUT
Refer to the DVD player's manual for operating instructions.

DMI IN 2

PCMCIA CARD SLOT EJECT HDMI/DVI IN 1 HDMI IN 2

DMI/DVI IN 1

PCMCIA CARD SLOT EJECT HDMI/DVI IN 1 HDMI IN 2 RGB IN

RGB(PC) AUD (RGB

When connecting HDMI cable
Connect the HDMI output of the DVD to the H D M I / D V I I N 1 or H D M I I N 2 jack on the set. Select HDMI1or HDMI2 input source with using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions.

Only 37/42LF7*, 42LY99 1

OPTICA
Connect the HDMI output of the DVD to the H D M I / D V I I N 1, H D M I I N 2 or H D M I I N 3 jack on the set. Select HDMI1, HDMI2 or HDMI3 input source with using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions.
RS-232C IN (CONTROL SERVICE) (CONTROL & SERVICE) ANTENNA IN

AUDIO (RGB/D

TV can receive the video and audio signal simultaneously with using a HDMI cable. If the DVD does not support Auto HDMI, you need to set the output resolution appropriately.

INSERTION OF CI MODULE

(This feature is not available in all countries.) - To view the scrambled (pay) services in digital TV mode.
PCMCIA CARD SLOT EJECT HDMI IN 1 HDMI IN 2
Insert the CI Module to P C M C I A (Personal Computer Memory Card International Association) C A R D S L O T of TV as shown. For further information, see p.48.
RS-232C RS-232 IN (CONTROL &

VCR SETUP

To avoid picture noise (interference), leave an adequate distance between the VCR and TV. Typically a frozenPCMCIA still pictureEJECT a VCR. If the 4:3 picture format is used; the fixed images on the sides of from the screen may CARD SLOT remain visible on the screen.
When connecting with an antenna

DIGITAL AUDIO OU

Wall Jack
Connect the A N T O U T socket of the VCR to the A N T E N N A I N socket on the set.

AV 1 AV 2

Connect the antenna cable to the A N T I N socket of the VCR.
Press the P L A Y button on the VCR and match the appropriate programme between the TV and VCR for viewing.

SETUPO Auto Config. PICTUREO Manual Config. AUDIOO XGA Mode Aspect Ratio TIMEO Reset OPTIONO SCREENO

button to

Press the G button to start Auto Config. When Auto Config. has finished, OK will be shown on screen. If the position of the image is still not correct, try Auto adjustment again. If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust the Manual Config.

Move MENU Prev.

Auto Config. Manual Config. XGA Mode Aspect Ratio Reset

To Set

Press the EXIT button to return to normal TV viewing.
Adjustment for screen Phase, Clock, Position
If the picture isnt clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually.
Its not available to use this function in 1:1 Pixel mode. To correct the screen size, adjust C l o c k. This function works in the following mode : RGB[PC]. C l o c k This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. P h a s e This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Press the MENU button and then use to select the SCREEN menu. Press the G button and then Manual Config.

button

Phase Clock H-Position V-Position

or E button to select

Press the G button and then D or E button to select Phase, Clock, H-Position or V-Position. Press the ments.
button to make appropriate adjust-

Selecting Wide XGA mode

To see a normal picture, match the resolution of RGB mode and selection of XGA mode. This function works in the following mode: RGB[PC] mode
Press the MENU button and then use D or E button to select the SCREEN menu. Press the G button and then use D or E button to select XGA Mode. Press the G button and then use D or E button to select the desired XGA resolution. Press the EXIT button to return to normal TV viewing.

1024 X X X X 768

TELETEXT These buttons are used for teletext. BUTTONS For further details, see the Teletext section. EXIT Clears all on-screen displays and returns to TV viewing from any menu.

Installing Batteries

Open the battery compartment cover on the back side and install the batteries matching correct polarity (+with +,-with -). Install two 1.5V AA batteries. Dont mix old or used batteries with new ones. Close cover.
REMOTE CONTROL KEY FUNCTIONS (Only 37/42/47/52LF6*, 37/42LF7*)
When using the remote control, aim it at the remote control sensor on the TV.
INPUT D/A TV/RADIO INPUT BRIGHT VCR SIMPLINK TEXT RATIO I/II MODE TV DVD
POWER Switches the set on from standby or off to standby. D/A INPUT Selects digital or analogue mode. Switches the set on from standby. TV/RADIO Selects Radio or TV channel in digital mode. INPUT External input mode rotate in regular sequence. Switches the set on from standby. Brightness Adjusts screen brightness. adjustment It returns to the default settings brightness by changing mode source.

BACK EXIT

EXIT Clears all on-screen displays and returns to TV viewing from any menu. BACK Allow the user to move back one step in an interactive application, EPG or other user interaction function.
MENU Selects a menu. INFO i Shows the present screen information.

7 LIST

9 Q.VIEW
GUIDE Shows programme schedule.
VOLUME UP Adjusts the volume. /DOWN FAV Displays the selected favourite programme. MUTE Switches the sound on or off.

UPDATE SLEEP SUBTITLE

INDEX HOLD

REVEAL

Programme Selects a programme. UP/DOWN 0~9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme table. Q.VIEW Returns to the previously viewed programme.

INPUT D/A TV/RADIO INPUT

MODE TV DVD
MODE Selects the remote operating modes. See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen.

BRIGHT VCR

SIMPLINK TEXT
TELETEXT These buttons are used for teletext. BUTTONS For further details, see the Teletext section. RATIO Selects your desired picture format. I/II Selects the sound output.
VCR/DVD Controls some video cassette recorders or DVD players control buttons when you have already selected DVD or VCR mode button. Control connected AV devices by pressing the D or E or F or G, OK buttons and buttons for play, stop, pause, fast reverse, fast forward, chapter skip. (The button does not provide such functions.) THUMBSTICK Allows you to navigate the on-screen menus and adjust (Up/Down/Left the system settings to your preference. Right)

MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Manual Tuning. Press the G button to select Storage. Select the desired programme number with the F or G button or NUMBER buttons on the Storage menu.
Press the E button to select System. Select a TV system with the F or G button; L : SECAM L/L (France) BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)

Storage

1 BG V/UHF 1
System Band Channel Fine Search Name C
Press the E button to select Band. Press the F or G button to select V/UHF or Cable as required. Press the E button to select Channel. You can select the desired channel number with the F or G button or NUMBER buttons. If possible, select the channel number directly with the NUMBER buttons.
Press the E button to select Search. Press the F or G button to commence searching. If a station is found the search will stop. Press the OK button to store it. To store another station, repeat steps 3 to 8. Press the EXIT button to return to normal TV viewing.
FINE TUNING (IN ANALOGUE MODE)
Normally fine tuning is only necessary if reception is poor.
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Manual Tuning. Press the G button and then D or E button to select Fine. Press the G button and then F or G button to fine tune for the best picture and sound. Press the OK button to store it. Press the EXIT button to return to normal TV viewing.
ASSIGNING A STATION NAME (IN ANALOGUE MODE)
You can assign a station name with five characters to each programme number.
Storage System Band Channel Fine Search Name C
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Manual Tuning. Press the G button and then D or E button to select Name. Press the G button and then D or E button. You can use a the alphabet A to Z, the number 0 to 9, +/ -, and blank. Press the F or G button to select the position and make your choice of the second character, and so on. Press the OK button to store it. Press the EXIT button to return to normal TV viewing.

Original When your TV receives the wide screen signal, it will be automatically changed to the picture format to be sent.

Spectacle

Original
) F u l l (Except 42LY99) When your TV receives the wide screen signal, when selected it will adjust the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully.
4:3 Following selection will lead you to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides.
16:9 Following selection will lead you to adjust the picture horizontally, in a linear proportion, to fill the entire screen (useful for viewing 4:3 formatted DVDs).
Zoom2 Choose Zoom2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage.
14:9 You can enjoy the picture format of 14:9 or general TV programme through the 14:9 mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left / right.
1 : 1 P i x e l (or J u s t S c a n(Only 37/42LF7*, 42LY99)) Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image.
Zoom1 Following selection will lead you to view the picture without any alternation, while filling the entire screen. However, the top and bottom portions of the picture will be cropped.
You can only select 4 : 3, : 9 (Wide), Zoom 1/2 in Component, HDMI mode. You can only select 4 : 3, : 9 (Wide) in RGB mode only. In HDMI (1080i 50Hz/60Hz, 1080p 24Hz/50Hz/60Hz) mode, 1:1 Pixel(or J u s t S c a n(Only 37/42LF7*, 42LY99)) is available.

PRESET PICTURE SETTINGS

Picture Mode-Preset
Dynamic Standard Mild User 1/2 Select this option to display with a sharp image. The most general and natural screen display status. Select this option to display with a mild image. Select this option to use the user-defined setting.

Dolby Digital PCM

Stereo/Dual Reception (In Analogue Mode Only)
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
Broadcast Mono Stereo Dual

On Screen Display

MONO STEREO DUAL I
Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono by pressing the I / I I button twice. In mono reception, the depth of sound is improved. To switch back to stereo, press the I / I I button twice again. Language selection for dual language broadcast If a programme received two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I / I I button repeatedly.

DUAL I DUAL II DUAL I+II

Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker.
NICAM Reception (In Analogue Mode Only)
If the set is equipped with the receiver for NICAM reception, the high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly.
When N I C A M m o n o is received, you can select N I C A M M O N O or F M M O N O.
When N I C A M stereo is received, you can select N I C A M S T E R E O or F M M O N O. If the stereo signal is weak, switch to F M m o n o.
When NICAM dual is received, you can select N I C A M D U A L I, N I C A M D U A L I I or N I C A M D U A L I + I I or M O N O.
Speaker Sound Output Selection
In AV, S-Video, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers.
Repeatedly press the I / I I button to select the sound output.
L+R: Audio signal from audio L input is sent to the left loud speaker and audio signal from audio R input is sent to the right loud speaker. L+L: Audio signal from audio L input is sent to left and right loud speakers. R+R: Audio signal from audio R input is sent to left and right loud speakers.
ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
Installation guide menu appears on TV screen when it is turned on for the first time.
Press the D or E or F or G button and then, O K button to select your desired language. Press the D or E button and then, O K button to select your country.
* If you want to change Language/ Country selection
Press the G button and then use D or E button to select Language. The menus can be shown on the screen in the selected language. Or, Press the G button and then use D or E button to select Country. Press the G button and then use F or G button to select your desired language or country. Press the O K button.

This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.

SWITCH ON/OFF

Press the T E X T button to switch to teletext. The initial page or last page appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the T E X T or E X I T button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

Page selection
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The PR D or E (or PR + or -) button can be used to select the preceding or following page.

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the PR D (or PR +) button can be used. The red button permits to return to previous selection. Alternatively the PR E (or PR -) button can be used.

Direct page selection

Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.

FASTEXT

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.

A Page selection

You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to Real data mapping 1. See page 109. Ack [t][ ][Set ID][ ][OK][Data][x] 15. Colour Temperature (Command 2 : u)
G To adjust colour temperature. You can also adjust Colour
[k][j][ ][Set ID][ ][Data][Cr] Data Red : 0 ~ Green : 64 * Refer to Real data mapping 1. See page 109. Ack [j][ ][Set ID][ ][OK][Data][x] 11. Sharpness (Command 2 : k) G To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 * Refer to Real data mapping 1. See page 109. Ack [k][ ][Set ID][ ][OK][Data][x] 12. OSD Select (Command 2 : l) G To select OSD (On Screen Display) on/off when controlling remotely.
Temperature in the PICTURE menu. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0: Cool Ack 1: Medium 2: Warm 3: User
[u][ ][Set ID][ ][OK][Data][x] 16. Red Adjustment (Command 2 : v)
G To adjust red in colour temperature.
Transmission [k][v][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50 * Refer to Real data mapping 2. See page 109. Ack [v][ ][Set ID][ ][OK][Data][x] 17. Green Adjustment (Command 2 : w)
G To adjust green in colour temperature.
[k][l][ ][Set ID][ ][Data][Cr] Data 0 : OSD off Ack 1 : OSD on
[k][w][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 50 * Refer to Real data mapping 2. See page 109. Ack [w][ ][Set ID][ ][OK][Data][x] 18. Blue Adjustment (Command 2 : $)
G To adjust blue in colour temperature.
[l][ ][Set ID][ ][OK][Data][x] 1 3. Remote control lock mode ( C o m m a n d 2 : m )
G To lock the front panel controls on the monitor and
remote control. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 0 : Lock off Ack 1 : Lock on
[k][$][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 50 * Refer to Real data mapping 2. See page 109. Ack [$][ ][Set ID][ ][OK][Data][x]
[m][ ][Set ID][ ][OK][Data][x] * If youre not using the remote control, use this mode. When main power is on/off, external control lock is released.
19. Abnormal State (Command 2 : z)
G To recognize an abnormal state.
21. Low Power (Command 1 : j, Command 2 : q)
G To reduce the power consumption of the set. You can
[k][z][ ][Set ID][ ][FF][ ][Cr] Data FF : Read Ack [z][ ][Set ID][ ][OK][Data][x] Data 0: Normal (Power on and signal exist) 1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down 7: Turn the monitor off by Fan Alarm function 8: Turn the monitor off by Off time function 9: Turn the monitor off by Auto sleep function * This function is read only.

Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture. (If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.
When moving the product to another place undo the ropes first. Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. To use the product safely make sure that the height of the bracket that is mounted on the wall is same as that of the product.
BACK COVER FOR WIRE ARRANGEMENT

Plasma TV models

Hold the CABLE MANAGEMENT with both hands and pull it as shown.

CABLE MANAGEMENT

Connect the cables as necessary. To connect an additional equipment, see the External equipment Connections section.
Reinstall the CABLE MANAGEMENT as shown.
LCD TV models (Except 37/42LF7*)
Connect the cables as necessary. To connect an additional equipment, see the E x t e r n a l e q u i p m e n t C o n n e c t i o n s section.
Install the C A B L E M A N A G E M E N T as shown.
Bundle the cables using the supplied twister holder. (This feature is not available for all models.)
How to remove the cable management
Hold the C A B L E M A N A G E M E N T with both hands and pull it upward.
Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.
LCD TV model (Only 37/42LF7*)
Install the C A B L E M A N A G E M E N T as shown. (Insert it as pushing the loops on the both sides of the cable management.)
Bundle the cables using the supplied twist holder. (This feature is not available for all models.)
Hold the C A B L E M A N A G E M E N T with both hands and pull it out. (Pull it out as holding the loops on the both sides of the cable management.)

RS-232C IN (CONTROL & SERVICE) SERVICE)

AUD (RGB

Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI1, HDMI2 or HDMI3 input source with using the I N P U T button on the remote control.
When connecting with a HDMI to DVI cable

Except 37/42LF7*, 42LY99

HDMI/DVI IN 1 HDMI IN 2
EJECT ECT HDMI/DVI IN 1 HDMI IN 2 RGB IN

TENNA IN

Connect theAUDIO audio output of the digital set-top box to VIDEO the A U D I O I N ( R G B / D V I ) jack on the set. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI1 input source with using the I N P U T AV 1 AV button on the remote 2control.

ANTENNA ENNA IN

Connect the digital set-top box to H D M I / D V I I N 1 jack on the set.
1 RS-232C IN (CONTROL & SERVICE)

I IN 1

EJECT CT
Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I ) jack on the set.
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI1 input source with using the I N P U T button on the remote control.

DVD SETUP

Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the set. Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the set. Turn on the DVD player, insert a DVD.
Select COMPONENT input source with using the I N P U T button on the remote control. Refer to the DVD player's manual for operating PCMCIA EJECT CARD SLOT HDMI/DVI IN 1 instructions.

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV

Y PB PR

PCMCIA CARD SLOT PR EJECT HDMI/DVI IN 1 HDMI IN 2

PB B-Y Cb Pb

Video output ports on DVD player

R-Y Cr Pr

When connecting with a Euro Scart
PCMCIA CARD SLOT EJECT RGB IN

C) AUDIO IN (RGB/DVI)

HDMI/DVI IN 1 HDMI IN Connect the Euro scart socket of the DVD to the2A V 1 Euro scart socket on the set.

PONENT IN

Turn on the DVD player,ANTENNA a DVD. insert
Select AV1 input source with using the I N P U T button on the remote control. RS-232C IN If connected to AV2 Euro scart socket, select AV2 input source. Refer to the DVD player's manual for operating instructions.

AUDIO/ VIDEO

(R) AUDIO (L)
If you want to use the EURO scart cable, you have to use the signal shielded Euro scart cable.
When connecting with an S-Video cable

VIDEO S-VIDEO

ANT IN
Connect the S-VIDEO output of the DVD to the S V I D E O input on the set. Connect the audio outputs of the DVD to the A U D I O input jacks on the set. Turn on the DVD player, insert a DVD. Select AV3 input source with using the I N P U T button on the remote control.

RS-232C P Select AV1 input source with using the I NIN U T button on the remote control.
V Connect the A U D I O/V I D E O jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select AV3 input source using the I N P U T button on the remote control.
If connected to A V 2 Euro scart socket, select AV2 input source.
When connecting with a RCA cable
If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the set.
Connect the S-VIDEO output of the VCR to the S V I D E O input on the set. The picture quality is improved; compared to normal composite (RCA cable) input. Connect the audio outputs of the VCR to the A U D I O input jacks on the set. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select AV3 input source with using the I N P U T button on the remote control.
If both S-VIDEO and VIDEO sockets have been connected to the S-VHS VCR simultaneously, only the S-VIDEO can be received.

DIGITAL AUDIO OUT SETUP

Send the TVs audio to external audio equipment via the Digital Audio Output (Optical) port.
EJECT HDMI/DVI IN 1 HDMI IN 2 R

RGB(PC

Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.
Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. Set the TV Speaker option - Off in the AUDIO menu. (Gp.78). See the external audio equipment instruction manual for operation.

1 OPTICAL

CAUTION
not look into the optical output port. Looking at the laser beam may damage your vision.

OTHER A/V SOURCE SETUP

Camcorder

Video Game Set

V Connect the A U D I O/V I D E O jacks between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red)
Select AV3 input source with using the I N P U T button on the remote control.

button to

Press the G button to start Auto Config. When Auto Config. has finished, OK will be shown on screen. If the position of the image is still not correct, try Auto adjustment again. If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust the Manual Config.

Move MENU Prev.

Auto Config. Manual Config. XGA Mode Aspect Ratio Reset

To Set

Press the EXIT button to return to normal TV viewing.
Adjustment for screen Phase, Clock, Position
If the picture isnt clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually.
Its not available to use this function in 1:1 Pixel mode. To correct the screen size, adjust C l o c k. This function works in the following mode : RGB[PC]. C l o c k This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. P h a s e This function allows you to remove any horizontal noise and clear or sharpen the image of characters.
Press the MENU button and then use to select the SCREEN menu. Press the G button and then Manual Config.

button

Phase Clock H-Position V-Position

or E button to select

Press the G button and then D or E button to select Phase, Clock, H-Position or V-Position. Press the ments.
button to make appropriate adjust-

Selecting Wide XGA mode

To see a normal picture, match the resolution of RGB mode and selection of XGA mode. This function works in the following mode: RGB[PC] mode
Press the MENU button and then use D or E button to select the SCREEN menu. Press the G button and then use D or E button to select XGA Mode. Press the G button and then use D or E button to select the desired XGA resolution. Press the EXIT button to return to normal TV viewing.

1024 X X X X 768

Initializing (Reset to original factory settings)
This function operates in current mode. To initialize the adjusted value Its not available to use ISM Method and Low power in L C D T V models.
Press the MENU button and then select the OPTION menu. Press the G button and then Factory Mode. Press the G button and then Factory Reset. Press the OK button.
SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTIONO SIMPLINK SCREENO Factory Mode
The message If you enter a password, all user setting will be reset will appear.
Use NUMBER buttons to input a 4-digit password.
Language Country Lock System Parental Control Input Label SIMPLINK Factory Mode
Set ID 1 Factory Reset OK ISM Method

Normal Low Power Off

Set ID 1 Factory Reset OK ISM Method Normal Low Power Off

*: This feature is not available in all countries.
SETUPO Sound Mode PICTUREO Auto Volume AUDIOO Balance TV Speaker TIMEO Digital Audio Out OPTIONO SCREENO
SETUPO Language PICTUREO Country AUDIOO Lock System Parental Control TIMEO Input Label OPTIONO SIMPLINK SCREENO Factory Mode Index
SETUPO Clock PICTUREO Off Time AUDIOO On Time Auto Sleep TIMEO Time Zone OPTIONO SCREENO
*: This feature is not available for all models.
Its not available to use ISM Method and Low power in L C D T V models. G In Analogue mode, 5V Antenna Power, CI Information, Software Update and Diagnostics will not display.
AUTO PROGRAMME TUNING (IN DIGITAL MODE)
Use it to automatically find and store all of the programmes. When you start auto programming in digital mode, all the stored service information will be deleted.
Press the MENU button and then D or E button to select the SETUP menu.
SETUPO Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit 5V Antenna Power TIMEO Software Update OPTIONO Diagnostics SCREENO CI Information
Press the G button and then D or E button to select Auto Tuning.
Press the G button to begin auto tuning. Use NUMBER buttons to input a 4-digit password in Lock System On. The message All service-information will be updated. Continue? will appear.
Auto Tuning Manual Tuning Programme Edit 5V Antenna Power Software Update Diagnostics CI Information
If you want to keep on auto tuning select YES with using the F or G button. Then, press the OK button. Otherwise select NO.
Auto Tuning Programme(s) Programme(s) %

MENU Stop

To stop auto tuning, press the MENU button.

UHF CH.

MANUAL PROGRAMME TUNING (IN DIGITAL MODE)
Manual Tuning lets you manually add a programme to your programme list.
Press the G button and then D or E button to select Manual Tuning.
Press the G button and then D or E button or NUMBER buttons to select the desired channel number. Use NUMBER buttons to input a 4-digit password in Lock System On.

Press the EXIT button to return to TV viewing.
Locking a programme (In Lock System On mode only) Select a programme to be locked with the D or E or F or G button. Press the GREEN button. The lock mark will appear in front of that programme number. Press the GREEN button again to release this function.
Note : To watch a locked programme, input a 4-digit password in Lock system. Be sure to remember this number! , , , G If you forgot your password, press on the remote control handset. G If you select other programme after releasing a locked programme and then return to the locked programme within 1 minute, you neednt input a password to select the locked programme.
Selecting favourite programme Select your favourite programme number by pressing D or E or F or G button and then press the FAV button on your remote control handset. It will automatically include the selected programme into your favourite programme list.
5V ANTENNA POWER (IN DIGITAL MODE ONLY)
Even if there isnt a special 5V adapter power in the external antenna, this function can output 5V in the set.
Press the G button and then use D or E button to select 5V Antenna Power.
Press the G button and then use D or E button to select On or Off.
In 5V Antenna Power On, if the set is short-circuit, it will automatically return to Off.

Off On

The message Antenna feed overloaded. Automatically switched off. will appear.
SOFTWARE UPDATE (IN DIGITAL MODE ONLY)
Software Update, means software can be downloaded through the digital terrestrial broadcasting system.

Q.VIEW MUTE

Press the MENU button and then select the SETUP menu.
Press the G button and then D or E button to select Software update. Press the G button and then D or E button to select Off or On. If you select On, a user confirm message box will be displayed to notify that new software is found.
* When setting Software Update
Occasionally, a transmission of updated digital software information will result in the following menu on the TV screen.
- During Progress of Software Update, please note the following: Select the YES using the or G button and when you see the following picture.
After Software Update is completed, the System takes about one minute to restart.
The power of the set must not be interrupted. The set must not be switched off. The antenna must not be disconnected. During this time, you should not switch off the power to the set. At this time, you should not work power On/Off. After Software Update, you can confirm the updated software version in Diagnostics menu.

POSITION SLEEP

SETUPO Auto Tuning PICTUREO Manual Tuning AUDIOO Programme Edit TIMEO OPTIONO SCREENO
Press the E button to select Storage From. Select the beginning programme number with the F or G button or NUMBER buttons on the Storage From menu.
Auto Tuning Manual Tuning Programme Edit
System Storage From Start
Press the E button to select Start. The station name is stored for stations which broadcast VPS (Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number. To stop auto tuning, press the MENU button. When auto tuning is completed, the Programme Edit menu appears on the screen. See the Programme Edit section to edit the stored programme.
MANUAL PROGRAMME TUNING (IN ANALOGUE MODE)
Manual Tuning lets you manually tune and arrange the stations in whatever order you desire.
Press the MENU button and then D or E button to select the SETUP menu. Press the G button and then D or E button to select Manual Tuning. Press the G button to select Storage. Select the desired programme number with the F or G button or NUMBER buttons on the Storage menu.
Press the E button to select System. Select a TV system with the F or G button; L : SECAM L/L (France) BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa / Australia) I : PAL I/II (U.K. / Ireland / Hong Kong / South Africa) DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)

Storage

1 BG V/UHF 1
System Band Channel Fine Search Name C
Press the E button to select Band. Press the F or G button to select V/UHF or Cable as required. Press the E button to select Channel. You can select the desired channel number with the F or G button or NUMBER buttons. If possible, select the channel number directly with the NUMBER buttons.
Press the E button to select Search. Press the F or G button to commence searching. If a station is found the search will stop. Press the OK button to store it. To store another station, repeat steps 3 to 8. Press the EXIT button to return to normal TV viewing.

Press the G button and then D or E button to select Red, Green or Blue.
Press the F or G button to make appropriate adjustments.

User Red Green Blue 0

XD - PICTURE IMPROVEMENT TECHNOLOGY
XD is LG electronic's unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. Its not available to use this function in PC[RGB/HDMI] mode.
Press the MENU button and then D or E button to select the PICTURE menu. Press the G button and then D or E button to select XD. Press the G button and then D or E button to select Auto or Manual. Press the E X I T button to return to normal TV viewing.

* Selecting the Manual

This menu is activated after selecting the User1 or User2 of P i c t u r e M o d e.
Picture Mode Colour Temperature
Auto Manual XD Contrast On XD Colour On XD NR Low MPEG NR 0
Advanced Picture Reset Demo
Press the G button and then D or E button to select X D Contrast, XD Colour, XD NR or MPEG NR. Press the G button and then D or E button to select On or Off. Press the E X I T button to return to normal TV viewing. X D C o n t r a s t : Optimizing the contrast automatically according to the brightness of the reflection. A X D C o l o u r : Adjusting the colors of the reflection automatically to reproduce as closely as possible to the natural colors. A X D N R : Removing the noise up to the point where it does not damage the original picture. A M P E G N R : To reduce the picture noise which may appear on the screen during watching the TV.
Use it to see the difference between XD Demo on and XD Demo off. Its not available to use this function in RGB[PC], HDMI[PC] mode.
Press the MENU button and then D or E button to select the PICTURE menu. Press the MENU button and then D or E button to select XD Demo. Press the G button to begin XD Demo.
To stop X D D e m o, press the M E N U or E X I T button.
TRUMOTION DEMO ( Only 42LY99)
Use it to see the difference between TruMotion Demo on and TruMotion Demo off. Its not available to use this function in RGB[PC], HDMI[PC] mode.

To Start

* Only 42LY99
Picture Mode Colour Temperature Advanced Picture Reset Demo TruMotion Demo
Press the MENU button and then D or E button to select the PICTURE menu. Press the MENU button and then D or E button to select TruMotion Demo. Press the G button to begin TruMotion Demo. To stop T r u M o t i o n D e m o, press the M E N U or E X I T button.

XD Demo

XD Off XD On

TruMotion Demo

MENU Exit

TruMotion On

TruMotion Off

ADVANCED - CINEMA

Set up the TV for the best picture appearance for viewing movies. This feature operates only in TV, AV, S-Video and Component 480i/576i, DTV mode.
Press the M E N U button and then D or E button to select the PICTURE menu. Press the G button and then D or E button to select Advanced. Press the G button and then D or E button to select Cinema. Press the F or G button to select On or Off. Press the E X I T button to return to normal TV viewing.
Cinema Off Black Level Low
ADVANCED - TRUMOTION ( Only 42LY99)
It is used for the best picture quality without any motion blur or judder when you enter a quick image or Film Source. This feature is disable in RGB-PC,HDMI-PC mode.
Picture Mode Colour Temperature Advanced Picture Reset Demo Cinema

F G On

Press the M E N U button and then D or E button to select the PICTURE menu. Press the G button and then D or E button to select Advanced. Press the G button and then D or E button to select TruMotion. Press the F or G button to select Off, Low or High.

Black Level Low

Picture Mode Colour Temperature Advanced Picture Reset Demo TruMotion Demo Cinema On Black Level Low TruMotion

FG High

Low Set amount of film judder to low. High Set amount of film judder to high.
* If you have some problem in viewing picture, set TruMotion to Lowor Off.
ADVANCED - BLACK(DARKNESS) LEVEL
When you watch the movie, this function adjusts the set to the best picture appearance. Adjusting the contrast and the brightness of the screen using the black level of the screen.
This function works in the following mode: AV (NTSC-M), S-Video (NTSC-M) or HDMI.
Press the G button and then D or E button to select Advanced.

Repeatedly press the I / I I button to select the sound output.
L+R: Audio signal from audio L input is sent to the left loud speaker and audio signal from audio R input is sent to the right loud speaker. L+L: Audio signal from audio L input is sent to left and right loud speakers. R+R: Audio signal from audio R input is sent to left and right loud speakers.
ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
Installation guide menu appears on TV screen when it is turned on for the first time.
Press the D or E or F or G button and then, O K button to select your desired language. Press the D or E button and then, O K button to select your country.
* If you want to change Language/ Country selection
Press the G button and then use D or E button to select Language. The menus can be shown on the screen in the selected language. Or, Press the G button and then use D or E button to select Country. Press the G button and then use F or G button to select your desired language or country. Press the O K button.
If you dont finish set up I n s t a l l a t i o n G u i d e by pressing E X I T button or time out of OSD (On Screen Display) display, it will continuously appear until completing set up whenever the set is turned on. If you select wrong local country, the teletext may not appear correctly on the screen and some problem may happen during teletext operation. CI (Common Interface) function may not be applied based on country broadcasting circumstance. DTV mode control buttons may not be working based on country broadcasting circumstance.
LANGUAGE SELECTION (IN DIGITAL MODE ONLY)
A u d i o function lets you select your preferred language for audio. If the audio data in selected language is not broadcasted, default language audio will be played. Use S u b t i t l e function when two or more subtitle languages are broadcasted. If the subtitle data in selected language is not broadcasted, default language subtitle will be displayed.
Press the G button and then use D or E button to select L a n g u a g e. Press the G button and then use D or E button to select A u d i o, S u b t i t l e or S u b t i t l e H a r d o f h e a r i n g. Press the G button and then use F or G button to select your desired language.

SLEEP SUBTITLE

< Audio Language Selection > G When two or more audio languages are broadcasted, you can select audio language with the I/II button on the remote control. G Press the D or E button to select an audio language. G Press the F or G button to select L+R, L+L or R+R. < Subtitle Language Selection > G When two or more subtitle languages are broadcasted, you can select subtitle language with the SUBTITLE button on the remote control. G Press the D or E button to select a subtitle language.
Audio Language OSD Information Display N.A Status Not Available MPEG Audio Dolby Digital Audio Audio for Visual Impaired Audio for Hearing Impaired
Subtitle Language OSD Information Display N.A
Status Not Available Teletext Subtitle Subtitle for Hard of Hearing
- The audio/subtitle can be displayed simpler form with 1 to 3 characters which is broadcast by service provider. - When you select supplementary Audio (Audio for Visual/Hearing Impaired) it may speak out a part of Main audio.

CLOCK SETUP

The clock is set automatically when receiving the digital signal. (You can set the clock if the TV has no DTV signal.) You must set to the time correctly before using on/off time function.
Press the MENU button and then select the TIME menu.
Press the G button and then D or E button to select Clock. Press the G button and then F or G button to select either the year, date, or time option. Once selected, use the D or E button to set the year, date, and time options.
Clock Off Time On Time Auto Sleep Time Zone

Time Date Year

14 Apr 2007
AUTO ON/OFF TIMER SETTING
The Off time automatically switches the set to standby at the preset time. Two hours after the set is switched on by the on time function it will automatically switch back to standby mode unless a button has been pressed. Once the on time/off time is set, these functions operate daily at the preset time. Off time function overrides On timer function if they are set both to the same time. The set must be in standby mode for the On timer to work.

SWITCH ON/OFF

Press the T E X T button to switch to teletext. The initial page or last page appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the T E X T or E X I T button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

Page selection
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The PR D or E (or PR + or -) button can be used to select the preceding or following page.

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the PR D (or PR +) button can be used. The red button permits to return to previous selection. Alternatively the PR E (or PR -) button can be used.

Direct page selection

Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.

FASTEXT

The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button.

A Page selection

Press the i button to select the index page. You can select the pages which are colour coded along the bottom line with the same coloured buttons. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The PR D or E (or PR + or -) button can be used to select the preceding or following page.
SPECIAL TELETEXT FUNCTIONS

A REVEAL

Press this button to display concealed information, such as solutions of riddles or puzzles. Press this button again to remove the information from the display.

A UPDATE

Displays the TV picture on the screen while waiting for the new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Press this button to view the updated teletext page.

A TIME

When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN, PR D or E (or PR + or -) or NUMBER buttons. Press again to exit this function.

A HOLD

Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inhibited. To continue press this button again.
*This function works in UK only.
The set gives you access to a digital teletext which is greatly improved in various aspects such as text, graphics and so on. This digital teletext can be accessed by special digital teletext services and specific services which broadcast digital teletext. You should select off from the subtitle language to display teletext by pressing SUBTITLE button.
TELETEXT WITHIN DIGITAL SERVICE
Press the numeric or PR D or E (or PR + or -) button to select a digital service which broadcasts digital teletext. To know which are digital teletext services, refer to the EPG service list. Follow the indications on digital teletext and move onto the next step by pressing TEXT, OK, D or E, F or G, RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on. To change digital teletext service, just select a different service by the numeric or PR D or E (or PR + or -) button. If pressing the MENU, GUIDE or INFO i button, the teletext service disappear temporarily. When pressing these buttons again, the teletext service is appeared.
TELETEXT IN DIGITAL SERVICE
Press the numeric or PR D or E (or PR + or -) button to select a certain service which broadcasts digital teletext. Press the TEXT or colour button to switch on teletext. Follow the indications on digital teletext and move onto the next step by pressing OK, D or E, F or G, RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on. Press the TEXT or colour button to switch off digital teletext and return to TV viewing. Some services may allow you to access text services by pressing the RED button. If pressing the MENU, GUIDE or INFO i button, the teletext service disappear temporarily. When pressing these buttons again, the teletext service is appeared.