The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system installers attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

CAUTION

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the users authority to operate this product
MFL34797033-en-simple 1/20/04 12:34 AM Page 3

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Do not use this apparatus near water.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
Unplug this apparatus during lighting storms or when unused for long periods of time.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Never touch this apparatus or antenna during a thunder or lighting storm. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock.

Electric Service Equipment
NEC: National Electrical Code
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit).
Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center.
GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
Power Supply Short-circuit Breaker
DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. Keep the product away from direct sunlight.
On Disposal (Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
MFL34797033-en-simple 1/20/04 12:34 AM Page 5

CONTENTS

WARNING / CAUTION. 2 SAFETY INSTRUCTIONS. 3 PREPARATION
Accessories. 6 Front Panel Information.7 Back Panel Information. 8 Remote Control Functions. 10 Back Cover for Wire Arrangement. 12 Attaching the TV to a wall. 14 Desktop Pedestal Installation. 14 Stand Installation. 15 VESA Wall Mounting. 15 Antenna or Cable Connection. 16 VCR Setup. 19 PC Setup. 20

WATCHING TV

Turning On TV. 21 Channel Selection. 21 Volume Adjustment. 21 Channel Search. 22 On-Screen Menus Selection. 23

Option Extras

This feature is not available for all models
2-Eye-bolts (Refer to p.14)
2-Wall brackets (Refer to p.14)

D-sub 15 pin Cable

For LCD TV models
32LC7D/7DC, 37LC7D, 32LG10 only

Cable Management

2- TV Bracket Bolts (Refer to p.14)
2- TV Brackets, 2- Wall Brackets (Refer to p.14)

Twist Holder

Arrange the wires with the twist holder.
4-Bolts for stand assembly (Refer to p.15)
MFL34797033-en-simple 1/20/04 12:34 AM Page 7

FRONT PANEL INFORMATION

Here shown may be somewhat different from your TV. NOTE: If your product has a protection tape attached, remove the tape. And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).

Front Panel Controls

Plasma TV Model
Power/Standby Indicator Illuminates red in standby mode. Illuminates green when the set is switched on.

Remote Control Sensor

INPUT ENTER

MENU VOL

ENTER CH

POWER Button

INPUT Button

MENU Button

ENTER Button

VOLUME (F,G)Buttons

CHANNEL (E,D)Buttons

LCD TV Model

CHANNEL(D,E)Buttons

ENTER MENU

VOLUME(F,G)Buttons ENTER Button MENU Button INPUT Button POWER Button
MFL34797033-en-simple 1/20/04 12:34 AM Page 8

BACK PANEL INFORMATION

Here shown may be somewhat different from your TV.

AV IN 2

VIDEO L/MONO AUDIO R

S-VIDEO

AV IN 1

RGB IN

ANTENNA/ CABLE IN

HDMI IN 2 2

RGB(PC)
AUDIO REMOTE DIGITAL AUDIO OUT (RGB/DVI) SERVICE CONTROL IN

OPTICAL

RS-232C IN (CONTROL & SERVICE)

COMPONENT IN

AUDIO OUT

1 HDMI/DVI IN 1

VIDEO AUDIO

(MONO)

HDMI IN

RGB IN RGB(PC)

DIGITAL AUDIO REMOTE AUDIO OUT (RGB/DVI) SERVICE CONTROL IN OPTICAL

COMPONENT IN 2 2

1 HDMI/DVI IN

S-VIDEO VIDEO

MFL34797033-en-simple 1/20/04 12:34 AM Page 9
AV (Audio/Video) IN Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power.

HDMI/DVI IN 1, HDMI IN 2 Connect a HDMI (DVI) connection to either input. COMPONENT IN Connect a component video/audio device to these jacks. RGB (PC) Connect the output from a PC. AUDIO (RGB/DVI) Connect the audio from a PC or DTV. SERVICE Remote Control Port Connect a wired remote control. ANTENNA/CABLE IN Connect over-the air signals to this jack. Connect cable signals to this jack. DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. RS-232C IN (CONTROL & SERVICE) PORT For external control devices. AUDIO OUT Connect analog audio to various types of equipment.
MFL34797033-en-simple 1/20/04 12:34 AM Page 10

REMOTE CONTROL FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.
MODE Select the remotes operating mode. TV, DVD, VCR, AUDIO, CABLE, or STB.

TV INPUT

DVD MODE CABLE

VCR STB

VCR/DVD Control video cassette recorders or DVD players. control buttons
MENU Displays the main menu. BRIGHT -/ + Adjust the brightness on screen.
THUMBSTICK Navigate the on-screen menus and adjust the system set(Up/Down/Left Right/ENTER) tings to your preference.
EXIT Clear all on-screen displays and return to TV viewing from any menu. TIMER Select the amount of time before your TV turns off automatically. RATIO Change the aspect ratio.

MUTE FAV

SIMPL RATIO
SIMPLINK See a list of AV devices connected to TV. When you toggle this button, the SimpLink menu appears at the screen. VOLUME UP Increase/decrease the sound level. /DOWN MUTE Switch the sound on or off. FAV Scroll through the programmed Favorite channels. CHANNEL Select available channels. UP/DOWN NUMBER button (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. BACK Tune to the last channel viewed.
MFL34797033-en-simple 1/20/04 12:34 AM Page 11
POWER Turns your TV or any other programmed equipment on or off, depending on the mode.
TV INPUT In AV 1-2, Component 1-2, RGB-PC, HDMI1, and HDMI2 input sources, screen returns to the last TV channel. INPUT External input modes rotate in regular sequence: TV, AV1-2, Component 1-2, RGB-PC, HDMI1 and HDMI2. (AV 1-2, Component 1-2, RGB-PC, HDMI1, and HDMI2 input sources are linked automatically, only if a device is connected.)

Inside the Sliding Cover

PICTURE ADJUST SOUND SAP
PICTURE Selects the factory preset picture depend on the viewing environment. SOUND Selects the factory preset sound for type of program. SAP Analog mode: Selects MTS sound (Mono, Stereo, or a SAP) DTV mode: Changes the audio language.

CC Select a closed caption. ADJUST Adjust the screen resolution, position, size and phase.

Installing Batteries

Remote control effective range

TV INPUT INPUT

Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). Install two 1.5V AA batteries. Dont mix old or used batteries with new ones. Close cover.

BRIGHT BRIGHT

BRIGHT
Use a remote control up to 7 meters distance and 30 degree (left/right) within the receiving unit scope. Dispose of used batteries in a recycle bin to preserve environment.
MFL34797033-en-simple 1/20/04 12:34 AM Page 12
BACK COVER FOR WIRE ARRANGEMENT
Hold the CABLE MANAGEMENT with both hands and pull it backward as shown.

CABLE MANAGEMENT

Connect the cables as necessary. To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT as shown.
MFL34797033-en-simple 1/20/04 12:34 AM Page 13

LCD TV Model PREPARATION

Bundle the cables using the supplied TWISTER HOLDER. (This feature is not available for all models.)
Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken.

TWISTER HOLDER

How to remove the CABLE MANAGEMENT
Hold the CABLE MANAGEMENT with both hands and pull it backward.
MFL34797033-en-simple 1/20/04 12:34 AM Page 14
ATTACHING THE TV TO A WALL
This feature is not available for all models. Here shown may be somewhat different from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children dont climb on or hang from the TV.
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product.

R (CONT

/DVI IN

2. How to use

Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box. operation) Select C o m p o n e n t 1 input source by using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2 input, select C o m p o n e n t 2 input source. Component 1/2 Yes Yes Yes Yes Yes HDMI1/DVI, HDMI2 No Yes Yes Yes Yes 1280x720p 1920x1080i Y, CB/PB, CR/PR Resolution 720x480i 720x480p Horizontal Frequency(KHz) 15.73 15.73 31.47 31.50 44.96 45.00 33.72 33.75 26.97 27.00 33.71 33.75 67.432 67.50 Vertical Frequency(Hz) 59.94 60.00 59.94 60.00 59.94 60.00

( 59.94 60.00 )

Y PB PR L R
Signal 480i 480p 720p 1080i 1080p

1920x1080p

23.976 24.00 29.97 30.00 59.94 60.00
MFL34797033-en-simple 1/20/04 12:34 AM Page 18

DVD SETUP

Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O 1 jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O 1 jacks on the set.

I/DVI IN

COMPONENT IN 2
Turn on the DVD player, insert a DVD. Select C o m p o n e n t 1 input source by using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2 input, select C o m p o n e n t 2 input source. Refer to the DVD player's manual for operating instructions.
When connecting HDMI cable
Connect the HDMI output of the DVD to the H D M I / D V I I N 1 or H D M I I N 2 jack on the set. No separated audio connection is necessary. ( ) HDMI supports both audio and video.

AUD (RGB/

COMPONENT I

HDMI/DVI IN

Select H D M I 1 or H D M I 2 input source by using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions.

HDMI-DVD OUTPUT

MFL34797033-en-simple 1/20/04 12:34 AM Page 19

VCR SETUP

ANT IN S-VIDEO VIDEO
When connecting with a RCA cable
V Connect the A U D I O/V I D E O jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red)

UDIO GB/DVI)

ANT OUT OUTPUT SWITCH
ANTENNA/ CABLE IN DIGITAL AUDIO OUT

OPTICAL 1

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) I Select A V 1 input source by using the I N P U T button on the remote control. I If connected to A V I N 2, select A V 2 input source.
REMOTE SERVICE CONTROL IN
If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the set.
When connecting with an S-Video cable
Connect the S-VIDEO output of the VCR to the S - V I D E O input on the set. Connect the audio outputs of the VCR to the A U D I O input jacks on the set.

UDIO B/DVI)

ANT IN

ANT OUT

OUTPUT SWITCH

REMOTE

SERVICE CONTROL IN

DIGITAL AUDIO OUT

( OPTICAL
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owners manual.) Select A V 1 input source by using the I N P U T button on the remote control. If connected to A V I N 2, select A V 2 input source.
The picture quality is improved: compared to normal composite (RCA cable) input.
Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.
MFL34797033-en-simple 1/20/04 12:34 AM Page 20

PC SETUP

When connecting D-sub 15pin cable
AUDIO REMOTE (RGB/DVI) SERVICE CONTROL IN
RS-232C IN (CONTROL & SERV
Connect the RGB output of the PC to the R G B ( P C) jack on the set. Connect the PC audio output to the A U D I O ( R G B / D V I) jack on the set.

S-VIDEO VI

Turn on the PC and the TV. Select R G B - P C input source by using the I N P U T button on the remote control.

RGB OUTPUT AUDIO

When connecting HDMI to DVI cable
Connect the DVI output of the PC to the H D M I / D V I I N 1 jack on the set. Connect the PC audio output to the A U D I O (RGB/DVI) jack on the set.

RGB IN HDMI IN

AUDIO (RGB/DVI)
Turn on the PC and the TV. Select HDMI1 input source by using the I N P U T button on the remote control.
Supported Display Specifications
RGB-PC, HDMI1/DVI-PC mode

DVI-PC OUTPUT AUDIO

Resolution 640x350 720x400 640x480 800x600 1024x768 1280x768 1360x768 1366x768
Horizontal Frequency(KHz) 31.469 31.469 31.469 37.879 48.363 47.776 47.720 47.130
Vertical Frequency(Hz) 70.08 70.08 59.94 60.31 60.00 59.87 59.799 59.65 * RGB-PC mode only
Depending on graphic card and signal status, there can be some shaking to find best picture in a little time.

* LCD TV only

MFL34797033-en-simple 1/20/04 12:34 AM Page 21

TURNING ON TV

DVD MODE
First, connect power cord correctly. At this moment, the TV switches to standby mode. I In standby mode to turn TV on, press the , INPUT, C H (D or E) button on the TV or press the POWER, INPUT, TV INPUT, C H (D or 9 E), Number (0~9 ) button on the remote control. Select the viewing source by using the TV INPUT, INPUT button on the remote control. I This TV is programmed to remember which power state it was last set to, even if the power cord is out. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode.

SAP CC

PICTURE
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

CHANNEL SELECTION

Press the C H (D or E) or NUMBER buttons to select a channel number.

VOLUME ADJUSTMENT

Adjust the volume to suit your personal preference.
Press the V O L (D or E) button to adjust the volume.
If you want to switch the sound off, press the M U T E button.
You can cancel the Mute function by pressing the MUTE or V O L (D or E) button.
MFL34797033-en-simple 1/20/04 12:34 AM Page 22

CHANNEL SEARCH

Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run Auto Tuning again after any Antenna/Cable connection changes. A password is required to gain access to Auto Tuning menu if the Lock System is turned on.

BRIG HT +

Auto Tuning
Press the M E N U button and then use D or E button to select the S E T U P menu.
Manual Tuning Channel Edit
Press the G button and then use D or E button to select A u t o T u n i n g.
Press the E N T E R button to begin the channel search. Allow A u t o T u n i n g to complete the channel search cycle for A N T E N N A and C A B L E.
Auto Tuning Manual Tuning Channel Edit
Selection ( G or ) leads you to the Auto Tuning screen.

Processing Auto Tuning.

Selection ( G or ) leads DTV Ch.23 you to the Auto Tuning Found Channel(s): 16 screen.

Analog TV antenna Digital DTV antenna Analog CATV cable Digital CADTV cable
Press to stop the current scan and start ANALOG ANTENNA channel scan.

MENU Prev

MFL34797033-en-simple 1/20/04 12:34 AM Page 23
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Press the M E N U button and then use D or E button to select the each menu. Press the G button and then use D
button to display the available menus.
All available TV channels are searched and stored automatically. User can do manual channel selection and add or delete individual channels. You can add or delete in the channel list.

PICTURE Picture Mode

Picture Mode Color Temperature XD Advanced Aspect Ratio Picture Reset Screen : 16:9 : User1 : Cool
Select the preset value in the Picture Mode menu based on the program category: Dynamic, Standard, Mild, User1, User2. Choose one of three automatic color adjustments : Cool, Medium, Warm, User

Color Temperature

It is LG Electronics unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. I Select Auto or Manual (XD Contrast, XD Color, XD Noise).

Advanced

Cinema 3:2 Mode (On, Off) Set up the TV for the best picture appearance for viewing movies. I Black Level (Low, High) Adjusting the contrast and the brightness of the screen using the black level of the screen.

Aspect Ratio

Select the desired picture format. : Set by program, 4:3, 1 6:9, Zoom1, Zoom2, Just Scan. Use to quickly reset all the Picture menu options to their original factory preset values. Adjust the screen Resolution, Position, Size, Phase, Reset.

Picture Reset Screen

MFL34797033-en-simple 1/20/04 12:34 AM Page 24
Sound Mode Auto Volume Balance TV Speaker : Standard : On :0 : On I I

Sound Mode

Sound Mode lets you enjoy the best sound without any special adjustment. : Standard, Music, Movie, Sports and User Scans for changes in sound levels during commercials, then adjusts the sound to match the specified audio level. Adjust the left/right sound of speaker. Turn the TV speaker On or off.

Auto Volume

Clock Off Time On Time Sleep Time Auto Sleep : Oct 19, 2006, 03:44 AM : Off : Off : Off : Off

Balance TV Speaker

Auto: The time is set automatically from a digital channel signal. Select your viewing area time zone. Select Auto, Off, On depending on whether or not your viewing area observes Daylight Saving time. Manual: Set the clock manually. Select On or Off. Select On or Off. Select the amount of time before your TV turns off automatically: Off, 10, 20, 30, 60, 90, 120, 180, 240. TV will be automatically turned off, in case of no signal for 10 minutes.
Off Time On Time Sleep Time Auto Sleep
MFL34797033-en-simple 1/20/04 12:34 AM Page 25

OPTION

Language Input Label SimpLink Key Lock Caption ISM Method Low Power Set ID : Off : Off : Off : Orbiter : Off :1 : English
Language Input Label SimpLink
Select your desired language for on screen menus : English, Spanish, French. Set a label to each input source. Control and play other AV devices connected to the TV through HDMI cable without additional cables and settings. This feature can be used to prevent unauthorized viewing by locking out the front panel controls.

key Lock

Plasma TV model only

Caption

Mode: When selecting Off, Submenus for Analog, DTV, and Digital Option become disabled. I Analog: CC1~ CC4 , Text1~ Text4. I Digital: Service1~ Service6 I Digital Option: Customize the DTV/CADTV captions that appear on your screen.
ISM Method Low Power Set ID
Use it to minimize any fixed image on the screen. : Normal, Orbiter, Inversion, White Wash. Reduces the plasma display power consumption. Choose the desired TV ID number.

For USA

Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block : Off
Lock System Set Password Block Channel Movie Rating TV Rating-Children

I I I I

Select On or Off. Change the password. Select a channel number that you wish to block. Blocks movies according to the movie ratings limits specified. Prevents children from watching certain children's TV programs, according to the ratings limit set. Based on the ratings, blocks certain TV programs that you and your family do not want to view. Selecting canadian english language rating system. Selecting canadian french language rating system. This function may become available in the future and will be available only for digital channel signal. Enables you to select a source to block from the external source devices you have hooked up.

For Canada TV Rating-General
Lock System Set Password Block Channel TV Rating-English TV Rating-French Downloadable Rating Input Block : Off
TV Rating-English TV Rating-French Downloadable Rating Input Block
MFL34797033-en-simple 1/20/04 12:34 AM Page 26

TROUBLESHOOTING

The operation does not work normally.
The remote control doesnt work
Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. I Install new batteries. Is the sleep timer set? Check the power control settings. Power interrupted. I No broadcast on station tuned with Auto off activated.
Power is suddenly turned off
The video function does not work. Check whether the product is turned on. Try another channel. The problem may be with the broadcast. I Is the power cord inserted into wall power outlet? I Check your antenna direction and/or location. I Test the wall power outlet, plug another products power cord into the outlet where the products power cord was plugged in.

No picture &No sound

Picture appears slowly after switching on
This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes.
No or poor color or poor picture
Adjust Color in menu option. Keep a sufficient distance between the product and the VCR. I Try another channel. The problem may be with the broadcast. I Are the video cables installed properly? I Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking Poor reception on some channels
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station. Station signal is weak, reorient antenna to receive weaker station. I Check for sources of possible interference.
Lines or streaks in pictures
Check antenna (Change the direction of the antenna).
MFL34797033-en-simple 1/20/04 12:34 AM Page 27
The audio function does not work. Press the VOL or VOLUME button. I Sound muted? Press MUTE button. I Try another channel. The problem may be with the broadcast. I Are the audio cables installed properly?
Picture OK & No sound
No output from one of the speakers Unusual sound from inside the product
Adjust Balance in menu option. A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
Adjust resolution, horizontal frequency, or vertical frequency. Check the input source.

Vertical bar or stripe on background & Horizontal Noise & Incorrect position Screen color is unstable or single color
Work the Auto configure or adjust clock, phase, or H/V position. (Option)
Check the signal cable. Reinstall the PC video card.
MFL34797033-en-simple 1/20/04 12:34 AM Page 28

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Heres a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until its almost dry, and then use it to wipe the screen. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for a long time (such as a vacation), its a good idea to unplug the power cord to protect against possible damage from lightning or power surges.
MFL34797033-en-simple 1/20/04 12:34 AM Page 29

PRODUCT SPECIFICATIONS

MODELS Including stand Dimensions (Width x Height x Depth) Excluding stand 42PC5D (42PC5D-UL) 42PC5DC (42PC5DC-UL) 41.3 x 30.2 x 12.2 inches 1048.0 x 766.0 x 310.0 mm 41.3 x 28.1 x 3.3 inches 1048.0 x 713.0 x 83.5 mm 61.7 pounds / 28.0 kg 54.2 pounds / 24.6 kg 50PC5D (50PC5D-UL) 50PC5DC (50PC5DC-UL) 48.9 x 34.9 x 14.6 inches 1242.0 x 887 x 370.0 mm.6 48.9 x 32.6 x 3.5 inches 1242.0 x 827 x 88.0 mm.2 86.6 pounds / 39.3 kg 76.3 pounds / 34.6 kg

Weight

including stand excluding stand
Power requirement Television System Program Coverage External Antenna Impedance Operating Temperature Operating Humidity Environment condition Storage Temperature Storage Humidity
AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-ohm 32 ~ 104F (0 ~ 40C) Less than 80% -4 ~ 140F (-20 ~ 60C) Less than 85%
MODELS Including stand Dimensions (Width x Height x Depth) Excluding stand
32LC7D (32LC7D-UK) 32LC7DC (32LC7DC-UK) 32LG10 (32LC7D-UK)

37LC7D (37LC7D-UK)

42LC7D (42LC7D-UK) 40.7 x 29.5 x 1 inches 1.033.4 x 750.0 x 287 mm.6 40.7 x 27.0x 3.5 inches 1 033.4 x 686.8 x 88.5 mm
31.8 x 23.9x 9.8 inches 36.5 x 27 x 1 inches.3 1.0 806.6 x 606.5 x 249.0mm 927 x 692.8 x 280.5 mm.0 31.8 x 21.7 x 3.1 inches 36.5 x24.8 x 3.5 inches 806.6 x 552.3 x 79.0 mm 927 x 630.0 x 88.0 mm.0 30.2 pounds / 13.7 kg 24.7 pounds / 1 kg 1.2

44.1 pounds / 20.0 kg 54.9 pounds / 24.9 kg 35.3 pounds / 16.0 kg 45.0 pounds / 20.4 kg
The specifications shown above may be changed without prior notice for quality improvement.
MFL34797033-en-simple 1/20/04 12:34 AM Page 30
OPEN SOURCE SOFTWARE NOTICE
The following GPL executables and LGPL/MPL libraries used in this product are subject to the GPL/LGPL/MPL License Agreements: GPL EXECUTABLES: I Linux kernel 2.6.12 I busybox LGPL LIBRARIES: I uclibc MPL LIBRARIES: I Nanox
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at: Opensource@lge.com This offer is valid for a period of three(3) years from the date of the distribution of this product by LG Electronics. You can obtain a copy of the GPL, LGPL and MPL licenses on the CD-ROM provided with this product.
This software is based in part on the work of the Independent JPEG Group. This software includes the Zlib compression library, developed by Jean-loup Gailly and Mark Adler. Copyright (C) 1995-2005 Jean-loup Gailly and Mark Adler
MFL34797033-en-simple 1/20/04 12:34 AM Page 31
MFL34797033-en-simple 1/20/04 12:34 AM Page 32

Re: Mopar model 812 car radio, (early 1950's Chrysler product)
Source: http://sci.techarchive.net/Archive/sci.electronics.repair/201105/msg00075.html
From: klem kedidelhopper <captainvideo462009@xxxxxxxxx> Date: Tue, 3 May 2011 10:02:(PDT) On May 3, 12:20 pm, klem kedidelhopper <captainvideo462.@xxxxxxxxx> wrote: On Apr 26, 3:55 pm, Meat Plow <mhywa.@xxxxxxxxx> wrote:
On Mon, 25 Apr 2011 21:12:48 0400, Michael A. Terrell wrote: Meat Plow wrote:
On Sun, 24 Apr 2011 23:44:39 0400, Michael A. Terrell wrote:

Meat Plow wrote:

On Sun, 24 Apr 2011 15:23:00 0400, Michael A. Terrell wrote:
A lot of old Re: Mopar model 812 car radio, (early 1950's Chrysler product) 1
Re: Mopar model 812 car radio, (early 1950's Chrysler product) car radios used a 262.5 KHz IF to prevent image problems at 910 KHz. 262.5 KHz puts them all out of band.
Old being before what year? I was just a young pup learning back in the 70's so I don't recall a 262 IF. Probably too much LSD later on.
Delco was still using 262.5 in the early '70s. I could repair most of their mid '60s to mid '70s AM radios in less than 15 minutes. Some took less than 5 Re: Mopar model 812 car radio, (early 1950's Chrysler product) 2
Re: Mopar model 812 car radio, (early 1950's Chrysler product) minutes. I still hve most of the H.W. Sams AR series manuals. The cheap Japanese radios used either 450 or 455 KHz IFs, which caused problems on 900 or 910 KHz.
Well that makes sense. I got pretty good on the Delco stuff. Mostly bad tubes, suppressor caps, stuck vibrators, things of that nature. Tweaking the receiver I usually did by ear going through each stage from start to finish. Then the antenna trimmer once it was back in the vehicle. I'm sure I have an old tube radio and a few parts up in the attic. Used to have one on my bench for music.
I gave away about 200 '50s through '70s car radios when I moved south, 25 years ago. Now, most are worth $100 to $1000. :(
Doesn't that piss you off.
Live Fast Die Young, Leave A Pretty Corpse
Send Invite 50 left Preview Invite < About these ads Power Switches & Relays Order Power Switches & Relays Now. Search and Save www.DowKey.com Archive Report spam Delete Move to Re: Mopar model 812 car radio, (early 1950's Chrysler product) 3
Re: Mopar model 812 car radio, (early 1950's Chrysler product) Labels More actions Refresh All None Read Unread Starred Unstarred of 108 Older : Oldest Mike, Eric, me (3) [tvrepair] Magnavox PTV 711 chassis model # FP5250W104 Poor little devil. Don't you think that Texas is carrying that death penalty thing a bit too & 10:44 am Shannen's Electronics [tvrepair] P/A RCA DLP M50WH74 (ATC351A) lamp door needed Customer brought in this RCA dlp M50WH74S (ATC351A) with the lamp door missing. I believe the & 10:42 am Jeff, Jim, me (3) [tvrepair] T/A KV36HSblinks Jesse. I found this on my group. I never knew about the service screen. It sounds like the set & 9:49 am jmiller WA#1755471 Jennifer Miller Sanyo Customer Service 3333 Sanyo Rd. Forrest City, AR. ext & Attachment May 2 jmiller WA#1741830 The message is ready to be sent with the following file or link attachments: P__1741830.142 Note & Attachment Apr 29 Jesse Stein Fwd: dog fence Forwarded message From: <stein.je.@xxxxxxxxx> Date: Tue, Apr 26, 2011 at 12:25 & Apr 26 Re: Mopar model 812 car radio, (early 1950's Chrysler product) 4
Re: Mopar model 812 car radio, (early 1950's Chrysler product) Milton, me (6) RE: LG refrigerator model LBN2251#** problems (UNCLASSIFIED) Classification: UNCLASSIFIED Caveats: NONE Glad to hear your surgery went well, hope you have & Apr 26 EricT [tvrepair] Re: Sanyo DP52449 LCD Need Manual Eric that's the nicest thing someone has done for me for awhile. Thank You. Eric Tindall & Apr 25 me. Paul, Jerry (12) Mopar model 812 car radio (Early 1950's Chrysler ) I got this set working and it actually works pretty well too. The vibrator buffer cap though & Apr 20 Eric Schmidt Sams for Mopar 812 Here.http://www.mediafire.com/?ygocccx3zpvpfjq Eric Rick Electronics in NYC eric7828@gmail & Apr 20 jmiller WA#1747390 Jennifer Miller Sanyo Customer Service 3333 Sanyo Rd. Forrest City, AR. ext & Attachment Apr 20 Ed M Re: Mopar model 812 car radio, (early 1950's Chrysler product) Sams, set 139, folder 8 Original Message From: "klem kedidelhopper & Apr 20 Milton, me (3) LG REF I would not condemn the defrost electronics until it reaches temp. From what you have said across & Attachment Apr 19 me, techsupport (3) WA 1740207 Thanks very much for the advice. I'll give it a shot. Lenny On Mon, Apr 18, 2011 at 3:50 PM & Apr 18 Re: Mopar model 812 car radio, (early 1950's Chrysler product) 5

Re: Mopar model 812 car radio, (early 1950's Chrysler product) garbe, Jeff, me (5) [tvrepair] Sylvania 27Z104 no vertical (old !) Glad to hear it. Sometimes we win some and sometimes, well, I have one of those "dog day & Apr 18 Peter Lacourse wrong board before getting fixed i had in the input menu usp mode 03 mode video1 video2 video3 hdmi1 hdmi2 & Apr 18 me. John, Eric, Milton (9) LG refrigerator model LBN2251#** problems One other thing I meant to ask. If the thermistor is shorted and the fuse is open, as they now & Attachment Apr 16 me. John, Technotronic (9) Infocus DLP IN2102 Thanks very much for thinking of ,me Steve. I did get into these things a bit more last week. A & Apr 15 jmiller, me (2) WA#1734593 Jen please send me a main for this set. Thanks, Lenny On Fri, Apr 15, 2011 at 11:36 AM & Attachment Apr 15 me, John, tvservice (4) STK392120 Thanks guys for the info. Funny I would have thought that the 150 would have trumped the other & Apr 15 milton, garbe, me (3) Re: [tvrepair] Sony KD36XSblinks? You could just replace the chips and hope for the best. Make sure to use DB's The resistors & Apr 15 me, Eric (3) Philipps Mag. 60PP9363H/17 convergence problems Thanks very much for the tip Eric. I'll look for cloudy fluid also Lenny On Wed, Apr 13, 2011 & Apr 13 Re: Mopar model 812 car radio, (early 1950's Chrysler product) 6
Re: Mopar model 812 car radio, (early 1950's Chrysler product) me, James (2).33ohm dual emitter resistors Klem I checked my inventory, turns out the resistors I have are.22 ohm/5w. They should work & Apr 13 me, techsupport (2) WA#1740207 Hello, I have attached the service manual and a troubleshooting guide. T.H. klem kedidelhopper & Attachment Apr 12 me, Eric, James, Jerry (6) Stereo receiver dual emitter resistors If there is a part number on it, you should look it up to see if it has a special temperature & Apr 8 jmiller WA#1740207 The message is ready to be sent with the following file or link attachments: DOC044 Note: To & Attachment Apr 8 Ardell, John, tomlee (4) [tvrepair] Vizio SP42A Plasma washed out Thank you. Yes, the heat sink on the Z board is running cold. I found an open fuse on it which I& Apr 5 jmiller, me (2) WA#1735520 Jen Please send me a main for this set. Thank you. Lenny On 4/1/11, jmil.@xxxxxxxxxxx & Attachment Apr 1 Bopp, Jonathan G FW: Legacy Model Discontinuation Plan This is the discontinuation letter but the exceeder will be totally compatible with any circuit & Mar 28 techsupport Re: Two WRA's: 1728064 Lenny, If TV makes a pop sound and goes off you will need to check voltages on connectors to see & Mar 24 techsupport Re: Mopar model 812 car radio, (early 1950's Chrysler product) 7

Re: Mopar model 812 car radio, (early 1950's Chrysler product) Re: Two WRA's: 1723214 Hello Lenny, When you check TV with your HDMI device and it dose not work then you probably have & Mar 24 klem kedidelhopper hilary Hilary As you requested, I'll meet you to discuss the new meeting room on Monday at the & Mar 18 jmiller WA#1728064 Jennifer Miller Sanyo Customer Service 3333 Sanyo Rd. Forrest City, AR. ext & Attachment Mar 18 jmiller, me (2) WA#1723214 Hi Jen Please send me a main for this set. Thanks, Lenny On Fri, Mar 11, 2011 at 3:09 PM & Attachment Mar 11 Jesse Stein Fwd: Tv specs Forwarded message From: <stein.je.@xxxxxxxxx> Date: Sat, Jan 15, 2011 at 5:34 & Mar 1 Eric Schmidt Toshiba 32AF45 Manual Attached. The source of the tip I posted about D508 was the Admin at Repair World. Eric Rick & Attachment Jan 26 me. LeRoy (27) Sylvania E5341 strange symptoms Hi LeRoy I just received the manual and service notes. There is a good deal of troubleshooting & Jan 11 walter. me, Jerry (6) Re: [tvrepair] Re: LG/Zenith model 42PC5DUL I tell the customers that just looking at it is free but that I have to charge for the time and & Jan 10 ncf8710, me (10) JVC Deck Hi Jesse, My phone number is 8602745302. The house has a Re: Mopar model 812 car radio, (early 1950's Chrysler product) 8
Re: Mopar model 812 car radio, (early 1950's Chrysler product) large dish antenna beside the garage & 12/13/10 nesesu, me (15), Draft Re: Driveway sensor, model 9171, mfg. around 1993 by "Detector Systems" On Sun, Oct 17, 2010 at 12:27 PM, klem kedidelhopper <captainvideo462.@xxxxxxxxx> wrote & Attachment 12/9/10 Jesse, me (4) poor mans well cap repair Jess I just spoke to Dick Bellemore about your well. He said that you could use a rubber coupling & Attachment 11/10/10 Jesse, me (4) Y SUS board Jess The set is either a 26 or a 32". You never know with John. Sometimes its days and & Attachment 11/9/10 me, techsupport (3) Sanyo DP46848 "Blotches" in screen Howard This is the set in question. I will follow up with some pictures shortly. Thanks, Lenny & 11/8/10 jmiller WA#1619704 Jennifer Miller Sanyo Customer Service 3333 Sanyo Rd. Forrest City, AR. ext & Attachment 11/8/10 me, techsupport (5) WRA 1596801 Thanks for the pictures. Please request: N7AF DISPLAY It looks like a T Con problem, but you have & 11/5/10 Ron Bath EMAIL ADDRESS CHANGE FYI: My NEW email address is: ronb.@xxxxxxxxxx "Capture the Moment" Ron Bath & 11/4/10 Starred me. Jim, tomlee (13) Sony KP51WS500 Sorry I forgot color pin K. So the total is 5 pins Tom Original Message >From & 11/4/10 Re: Mopar model 812 car radio, (early 1950's Chrysler product) 9

Re: Mopar model 812 car radio, (early 1950's Chrysler product) me. Jerry, Paul (13) Overhead projector repeated lamp failure The supplier says"We haven't noticed any problems with those lamps".But of course & 11/3/10 me, Ohger1 (7) Zenith P50W38 Hi John, This is Jesse, Lennys son. I believe we had some correspondence a while back in regards & Attachment 11/2/10 stein.jesse some more information on the flat panel Hi dad, I found some more information on the Zenith flat panel. From what I am seeing most say it & 11/1/10 Archive Report spam Delete Move. read more
I'm really sorry guys. It looks like somehow almost everything I've written over the past few weeks was (for want of a better term) "vomited" into my last post, (which incidentally never even appeared Here it is: I got this set working and it actually works pretty well too. The vibrator buffer cap though shows very slight leakage and I would like to replace it. The original is a.0047mfd@ 1600V. I know that the cap and transformer make up a kind of "tuned circuit" on these old radios but I'm not sure how critical that was. I have a nice mylar.0056mfd@ 2000V in my parts box and I although I wouldn't think so, I wonder if that might be too far off from the OEM value to do the job. Thanks, Lenny.