Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen these bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the TV.

! NOTE

When moving the TV undo the cords first. Use a platform or cabinet strong and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
BACK COVER FOR WIRE ARRANGEMENT

PLASMA TV Models

Connect the cables as necessary.
To connect additional equipment, see the E x t e r n a l E q u i p m e n t S e t u p section.
Install the C A B L E M A N A G E M E N T C L I P as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables.

(Only 42/50PG10**)

(Only 42/50PG20**, 42/50/60PG30**)

CABLE HOLDER

CABLE MANAGEMENT CLIP
How to remove the cable management clip
Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward. * For the 42PG10** model, press the center of the CABLE MANAGEMENT CLIP and then lift up it.
LCD TV Models: 26/32/37/42LG30** 32/37/42/47/52LG50**
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. Open the C A B L E M A N A G E M E N T C L I P as shown and manage the cables.
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section.
Install the CABLE MANAGEMENT CLIP as shown.
Fit the C A B L E M A N A G E M E N T C L I P as shown.
How to remove the cable management clip (LCD TV Models : 19/22LS4D*)
First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward.
G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.
To connect additional equipment, see the External Equipment Setup section of the manual.
Hold the CABLE MANAGEMENT CLIP with both hands and pull it backward.
POSITIONING YOUR DISPLAY (Only 19/22LG30**, 19/22LS4D*)

Tilt range

Image shown may differ from your TV. Adjust the position of the panel in various ways for maximum comfort.
LOCATION (Only 19/22LG30**, 19/22LS4D*)
Position your TV so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the tv to any unnecessary vibration, moisture, dust or heat. Also ensure that the TV is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV. When you install the TV to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.

KENSINGTON SECURITY SYSTEM (Only 19/22LG30**, 19/22LS4D*)
The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. For the detailed installation and use of the Kensington Security System, refer to the users guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. NOTE - The Kensington Security System is an optional accessory. NOTES a. If the TV feels cold to the touch, there may be a small flicker when when it is turned on. This is normal, there is nothing wrong with TV. b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV.

4 inches

WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
4 inches 4 inches 4 inches 4 inches
Not using the desk-type stand
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the P R O T E C T I O N C O V E R into the TV until clicking sound.

PC SETUP

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
Connecting with a D-sub 15 pin cable
Connect the RGB output of the PC to the R G B I N ( P C ) jack on the TV. Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. Turn on the PC and the TV
Select R G B input source using the INPUT button on the remote control.

RGB OUTPUT

Connect the DVI output of the PC to the H D M I / D V I I N, H D M I / D V I I N 1 ( D V I ) or H D M I / D V I I N 1 jack on the TV. Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. Turn on the PC and the TV. Select HDMI/DVI or HDMI 1 input source using the I N P U T button on the remote control.
enjoy vivid picture and sound, connect a PC to the TV. G Avoid keeping a fixed image on the TVs screen for prolonged periods of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. G Connect the PC to the RGB (PC) or HDMI IN (or HDMI/DVI IN) port of the TV; change the resolution. G There may be interference relating to resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode to another resolution or change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. synchronization input waveform for G The Horizontal and Vertical frequencies are separate. G Connect the signal cable from the monitor output port of the PC to the RGB (PC) port of the TV or the signal cable from the HDMI output port of the PC to the HDMI IN (or HDMI/DVI IN) port on the TV.

G Connect

the audio cable from the PC to the Audio input on the TV. (Audio cables are not included with the TV). G If using a sound card, adjust PC sound as required. G This TV uses a VESA Plug and Play Solution. The TV provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically when using this TV. G DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode. G If required, adjust the settings for Plug and Play functionality. G If the graphic card on the PC does not output analogue and digital RGB simultaneously, connect only one of either RGB or HDMI IN (or HDMI/DVI IN) to display the PC output on the TV. G If the graphic card on the PC does output analogue and digital RGB simultaneously, switch the TV to either RGB or HDMI; (the other mode is set to Plug and Play automatically by the TV.) G DOS mode may not work depending on the video card if you use a HDMI to DVI cable. G If you use too long an RGB-PC cable, there may be interference on the screen. We recommend using under 5m of cable. This provides the best picture quality.

Supported Display Resolution (Only 19/22LS4D*)

RGB[PC], HDMI[PC] mode

Resolution 720x400 640x480 800x600 832x624 1024x768 1280x768 1360x768 1366x768 1280x1024 1440x900 1400x1050 1680x1050 Horizontal Frequency(kHz) 31.468 31.469 37.684 37.879 46.875 49.725 48.363 56.470 60.123 47.78 47.72 47.56 63.595 55.5 64.744 65.16 Vertical Frequency(Hz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.029 59.87 59.8 59.6 60.0 59.90 59.948 59.94

HDMI[DTV] mode

Resolution 720x480 720x576 1280x720 Horizontal Frequency(kHz) 31.469 31.5 31.25 37.500 44.33.72 33.75 28.125 26.33.716 33.75 56.250 67.43 67.5 Vertical Frequency(Hz) 59.59.59.50.00 23.29.976 30.59.94 60

1920x1080

Only 19LS4D* Only 22LS4D*
Supported Display Resolution
(Only 19/22/26/32/37/42LG30**, 32/37/42/47/52LG50**)
Resolution 720x400 640x480 800x600 832x624 1024x768 1280x768 1360x768 1366x768 1440x900 1400x1050 1680x1050 1280x1024 1920x1080 Horizontal Frequency(kHz) 31.468 31.469 37.684 37.879 46.875 49.725 48.363 56.470 60.123 47.78 47.72 47.56 55.5 64.744 65.16 63.595 66.647 Vertical Frequency(Hz) 70.08 59.94 75.00 60.31 75.00 74.55 60.00 70.00 75.029 59.87 59.8 59.6 59.90 59.948 59.94 60.0 59.988
Resolution 720x480 720x576 1280x720 Horizontal Frequency(kHz) Vertical Frequency(Hz)
31.469 / 31.5 59.94 / 60 31.37.44.96 / 45 59.94 / 60 33.72 / 33.75 59.94 / 60 28.125 50.00 26.97 / 27 23.97 / 24 33.716 / 33.75 26.976 / 30.00 56.67 / 67.43.5 59.94 / 60
Only 19LG30** Only 22LG30** Only 19LG30**, 37/42/47/52LG50** Only 37/42/47/52LG50**
Supported Display Resolution (Only 42/50PG10**, 42/50PG20**, 42/50/60PG30**)
Resolution 720x400 640x480 800x600 1024x768 1280x768 1360x768 1920x1080 Horizontal Frequency(kHz) 31.468 31.469 37.879 48.363 47.78 47.72 66.647 Vertical Frequency(Hz) 70.08 59.94 60.31 60.00 59.87 59.80 59.988
Resolution 640x480 720x480 720x576 1280x720 Horizontal Frequency(kHz) 31.469 31.469 31.47 31.50 31.25 37.50 44.96 45.00 28.125 33.72 33.75 27.000 33.75 56.25 67.433 67.50 Vertical Frequency(Hz) 59.94 60.00 59.94 60.00 50.00 50.00 59.94 60.00 50.00 59.94 60.00 24.50.00 59.94 60

Screen Setup for PC mode

Screen Reset
Returns to the default settings Position, Size and Phase at the factory. This function works in the following mode : RGB[PC].

PICTURE

SCREEN
Resolution Auto Config. Position Size Phase Reset

RETURN Prev.

Contrast : 70 Brightness : 50 Sharpness : 50 Colour : 50 Tint :0 Advanced Control Picture Reset Screen

To Set

1MENU 2

Select PICTURE.

Select SCREEN.

Select Reset.

Select Yes.

Run Reset.

Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.
Adjustment for screen Position, Size, Phase
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This function works in the following mode : RGB[PC].

Resolution Auto Config.

Position Size Phase Reset
Select Position, Size or Phase.
Make appropriate adjustments.

Selecting Resolution

To view a normal picture, match the resolution of RGB mode and selection of PC mode. This function works in the following mode: RGB[PC] mode.

1024 x x x x 768

Except for PLASMA TV

Select Resolution.

Select the desired resolution.
Auto Configure (RGB [PC] mode only)
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. Auto configure This function is for automatic adjustment of the screen position, clock, and phase The displayed image will be unstable for a few seconds while the auto configuration is in progress.
If the position of the image is still not correct,
try Auto adjustment again.
If picture needs to be adjusted again after Auto
adjustment in RGB (PC), you can adjust the P o s i t i o n, S i z e or P h a s e.

Select Auto Config.

Run Auto Config.
REMOTE CONTROL KEY FUNCTIONS (Only 19/22LS4D*)
When using the remote control, aim it at the remote control sensor on the TV. POWER Switches the TV on from standby or off to standby.

TV D/A POWER INPUT

D/A INPUT Selects digital or analogue mode. Switches the TV on from standby. INPUT External input mode rotate in regular sequence. Switches the TV on from standby.

TV/RADIO TEXT

7 LIST

9 Q.VIEW

AV MODE
TV/RADIO Selects Radio or TV channel in digital mode. I/II Selects the sound output. MUTE Switches the sound on or off. 0~9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme table. Q.VIEW Returns to the previously viewed programme.

INFO i

EXIT RETURN VOL
MENU Selects a menu. AV MODE It helps you select and set images and sounds when connecting AV devices. INFO i Shows the present screen information. GUIDE Shows programme schedule.

RATIO INDEX

SLEEP TIME
SUBTITLE UPDATE HOLD REVEAL
THUMBSTICK Allows you to navigate the on-screen menus and adjust (Up/Down/Left the system settings to your preference. Right)
OK Accepts your selection or displays the current mode.
VOLUME UP Adjusts the volume. /DOWN RETURN(EXIT) Allows the user to move back one step in an interactive application, EPG or other user interaction function. * No function FAV Displays the selected favourite programme. Programme Selects a programme. UP/DOWN

DIAGNOSTICS (IN DIGITAL MODE ONLY)
This function enables you to view information on the Manufacturer, Model/Type, Serial Number and Software Version. This displays the information and signal strength of the tuned MUX. This displays the signal information and service name of the selected MUX.

Engineering Diagnostics

Manufacturer Model/Type Serial No. Software Version CH 30 CH 34 CH 36 CH 38 CH 54 CH 60
Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics Diagnostics CI Information
: LG Electronics Inc. : 22LS4D : 708KGKG00019 : V1.18.1

MENU Exit

Select Diagnostics.
Display Manufacturer, Model/Type, Serial Number and Software Version.
Display the information of Channel.
CI [COMMON INTERFACE] INFORMATION
This function enables you to watch some encrypted services (pay services). If you remove the CI Module, you cannot watch pay services. When the module is inserted into the CI slot, you can access the module menu. To purchase a module and smart card, contact your dealer. Do not repeatedly insert or remove a CAM module from the TV. This may cause a malfunction. When the TV is turned on after inserting a CI Module, you may not have any sound output. This may be incompatible with the CI module and smart card. CI (Common Interface) functions may not be possible depending upon the country broadcasting circumstances.

Viaccess Module

Consultations Authorizations Module information
Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information CI Information

Select the item

This OSD is only for illustration and the menu options and screen format will vary according to the Digital pay services provider. It is possible for you to change CI (Common Interface) menu screen and service by consulting your dealer.

Select CI Information.

Select the desired item: Module information, smart card information, language, or software download etc. Save.
SELECTING THE PROGRAMME TABLE
You can check which programmes are stored in the memory by displaying the programme table.
Displayed when the Locked Programme.
Displaying programme LIST
You may find some blue programmes. These
display the PROGRAMME LIST.
have been set up to be skipped by auto programming or in the programme edit mode. Some programmes with the channel number shown in the programme LIST indicate there is no station name assigned.

Q. MENU

Select the desired picture format.
You can also adjust Aspect Ratio in the

PICTURE or Q.MENU menu.

For Zoom Setting, select : 9, Z o o m 1
and Z o o m 2 in Ratio Menu. After completing Zoom Setting, the display goes back to Q.MENU.
16:9 The following selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire screen(useful for viewing 4:3 formatted DVDs).
4:3 The following selection will allow you to view a picture with an original 4:3 aspect ration, grey bars will appear on both the left and right of the screen.
Original When your TV receives a wide screen signal it will automatically change to the picture format broadcast.
Zoom2 Choose Zoom 2 when you wish the picture to be altered, both horizontally extended and vertically cropped. The picture adopting a compromise between alteration and screen coverage.

Original

G G G G
14:9 You can view a picture format of 14:9 or a general TV programme in the 14:9 mode. The 14:9 screen is viewed in the same way as in 4:3, but is magnified to the left and right.
Just Scan Following Selection will lead to you view the picture of best quality without loss of original picture in high resolution image. Note: If there are interference in original picture, you can view interference at the edge.

Just Scan

Zoom1 The following selection will allow you to view the picture without any alteration, while filling the entire screen. However, the top and bottom of the picture will be cropped.
You can only select 16:9 (Wide), 4:3, 14:9, Zoom 1/2 in Component (under 720p) mode. You can only select 4:3, 16:9 (Wide) in RGB/HDMI[PC] mode only. In HDMI/Component (over 720p) mode, Just Scan is available. You can only select Original in UK digital teletext (MHEG-5).

PRESET PICTURE SETTINGS

Picture Mode-Preset
It is possible to use Intelligent Sensor in 32/37/42/47/52LG50** models only. G In PLASMA TV models, Backlight will not be displayed.
Aspect Ratio : 16:9 Picture Mode :: Vivid Picture Mode Vivid Backlight Contrast Brightness Sharpness Colour Tint

100 Contrast Fresh Noise 70 Reduction Gamma 50 Black 50 Level Film Mode 50 Colour Standard 0
White Balance Red Contrast
Off Off Medium High On SD Warm 0
PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast Optimizes the contrast automatically according to the brightness of the reflection. Fresh Colour Adjusts the colour of the reflection automatically to reproduce as close as possible natural colours. Noise Reduction Removes interference up to the point where it does not damage the original picture.
Gamma High gamma values display whitish images and low gamma values display high contrast images.
Colour Temperature Fresh Contrast Fresh Colour Noise Reduction Gamma Black Level Eye Care Film Mode Close
Select Fresh Contrast, Fresh Colour, Noise Reduction or Gamma.

ADVANCED - FILM MODE

To set the TV up for the best picture quality for viewing films. This feature operates only in TV, AV and Component 480i/576i/1080i mode.

Select Film Mode.

ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjusts the TV to best picture quality. This function works in the following mode: AV (NTSC-M), HDMI or Component.
L o w : The reflection of the screen gets darker. H i g h : The reflection of the screen gets

brighter.

A u t o : Realizing the black level of the screen
and set it to High or Low automatically.

Select Black Level.

Select Low or High.

EYE CARE (LCD TV ONLY)

It helps you adjust brightness when the screen is too bright to prevent dazzling.

Select Eye Care.

PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Backlight 100 Contrast 100 Brightness 50 Sharpness 70 Colour 70 Tint 0 Advanced Control Picture Reset
Backlight 100 Contrast 100 Brightness 50 Sharpness video 70 i Resetting configuration. Colour 70 R Tint 0 Advanced Control Picture Reset

Select Picture Reset.

Initialize the adjusted value.
IMAGE STICKING MINIMIZATION (ISM) METHOD

(PLASMA TV ONLY)

A frozen or still picture from a PC/Video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the screen for prolonged periods. White wash White wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the screen will move every 2 minutes. Inversion This function inverts the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.

Input Label SIMPLINK Key Lock Set ID ISM Method ISM Method Power Saving Factory Reset

: On : Off

: Level 0
: On : Off Normal Normal : LevelOrbiter 0 Inversion White wash

Select ISM Method.

Select Normal, Orbiter, Inversion or White wash. Save.
If you do not need this function, set N o r m a l.
POWER SAVING PICTURE MODE (PLASMA TV ONLY)
This function allows you to reduce the power consumption of the TV.
Input Label SIMPLINK Key Lock Set ID ISM Method Power Saving Power Saving Factory Reset
: On : Off Level 0 Level 0 : LevelLevel Level 2 Level 3 Level 4

Select Power Saving.

Select Level 0, Level 1, Level 2, Level 3 or Level 4. Save.
Level 0 is the brightest.
In 19/22LS4D* Models, TV Speaker will not be displayed.

AUTO VOLUME LEVELER

AVL automatically remains on the same level of volume if you change programmes.
Auto Volume : Off Auto Volume : Off Balance Sound Mode : Standard 120Hz 200Hz 500Hz 1.2KHz 3KHz

Select AUDIO.

Select Auto Volume.
PRESET SOUND SETTINGS-SOUND MODE
You can select your preferred sound setting; SRS TruSurround XT or (SRS TruSurround HD (32/37/42/47/52LG5010 Only)), Clear Voice, Standard, Music, Cinema, Sport or Game and you can also adjust the frequency of the equalizer. Sound Mode lets you enjoy the best sound without any Special adjustment as the TV sets the appropriate sound options based on the programme content. SRS TruSurround XT or (SRS TruSurround HD (32/37/42/47/52LG5010 Only)), Clear Voice, Standard, Music, Cinema, Sport and Game are preset for optimum sound quality at the factory.
Auto Volume Balance Sound Mode Sound Mode : Off 0 Standard : :Standard 120Hz 200Hz 500Hz 1.2KHz 3KHz
Auto Volume Balance Sound Mode Sound Mode
: Off 0 : :Standard Standard 120Hz 200Hz 500Hz 1.2KHz 3KHz
SRS TruSurround XT Clear Voice Standard R Standard L Music Cinema Sport Game
If you select C l e a r V o i c e,
S R S T r u S u r r o u n d X T feature will not work.
Select Sound Mode. Select SRS TruSurround XT or (SRS TruSurround HD (32/37/42/47/52LG5010 Only)), Clear Voice, Standard, Music, Cinema, Sport or Game.

This feature is not available in all countries.
Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programmes, share prices and many other topics. The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.

SWITCH ON/OFF

Press the T E X T button to switch to teletext. The initial page or last page viewed appears on the screen. Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the T E X T button to switch off teletext. The previous mode reappears.

SIMPLE TEXT

Page selection TELETEXT
Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The P (or (PR + - or P + -)) button can be used to select the preceding or following page.

TOP TEXT

The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
With the blue button you can progress from block to block. Use the yellow button to proceed to the next group with automatic overflow to the next block. With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the P (or PR +) button can be used. The red button returns to the previous selection. Alternatively the P (or PR -) button can be used.

Direct page selection

As with SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.

Horizontal/vertical bars or picture shaking Poor reception on some channels Lines or streaks in pictures No picture when connecting HDMI
Check for local interference such as an electrical appliance or power tool.
Station or cable channel experiencing problems, tune to another station. Station signal is weak, reposition the antenna to receive weaker stations. A Check for sources of possible interference.
Check antenna (Change the position of the antenna). Check HDMI cable over version 1.3. If the HDMI cables dont support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
Picture OK & No sound
Press the VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? Adjust Balance in menu option. A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. Check HDMI cable over version 1.3. Check USB cable over version 2.0.
No output from one of the speakers Unusual sound from inside the TV No sound when connecting HDMI or USB
*This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range (Invalid format) Vertical bar or stripe on background & Horizontal Noise & Incorrect position Screen colour is unstable or single colour
Adjust resolution, horizontal frequency or vertical frequency. Check the input source.
Use Auto configure or adjust clock, phase or H/V position. (Option)
Check the signal cable. Reinstall the PC video card.

MAINTENANCE

Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.

47LG50** MODELS 47LG5000-ZA 47LG5010-ZD 47LG5020-ZB 47LG5030-ZE
1 56.2 x 81 x 342.9 mm 1 3.1 45.6 x 32.0 x 1 inches 3.56.2 x 739.2 x 103.0 mm 1 45.6 x 29.1 x 4.1 inches 29.2 kg / 64.4 lbs 24.6 kg / 54.3 lbs AC100-240V~ 50/60Hz 3.0A 300W
52LG50** 52LG5000-ZA 52LG5010-ZD 52LG5020-ZB 52LG5030-ZE
1 291.7 x 892.1 x 342.9 mm 7 50.9 x 35.2 x 1 inches 3.291.7 x 81.0 x 1 5.3 mm 50.9 x 32.2 x 4.6 inches 39.5 kg / 87 lbs.1 34.9 kg / 77 lbs.0 AC100-240V~ 50/60Hz 3.3A 330W

with stand without stand

PROGRAMMING THE REMOTE CONTROL
The remote control is a multi brand or universal remote. It can be programmed. to operate most remote controlled devices from other manufacturers. Note that the remote control may not control all models from other brands.
Programming a code into a remote mode
Testing your remote control. To find out whether your remote control can operate other components without programming, turn on a component such as a STB and press the corresponding mode button (such as a S T B) on the remote control, while pointing at the component. Test the POWER and P buttons to see if the component responds correctly. If the component does not operate correctly, the remote control requires programming to operate the device. Switch on the component to be programmed, then press the corresponding mode button (such as S T B) on the remote control. The remote control button of the desired device is illumintated.
Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed with the code.
Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. If the code is correct, the device will turn off. Press the M E N U button to store the code. Test the remote control functions to see if the component responds correctly. If not, repeat from step 2.
ALPHASTAR DSR AMPLICA BIRDVIEW CHANNEL MASTER
PROSAT RCA REALISTIC SAMSUNG SATELLITE SERVICE CO

057 138

036 CHAPARRAL 008 CITOH 054 CURTIS MATHES 050 DRAKE DX ANTENNA 024 ECHOSTAR ELECTRO HOME 089 EUROPLUS FUJITSU GENERAL INSTRUMENT HITACHI 139

Type of Connector; D-Sub 9-Pin Male
No. 9 Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection

RS-232C Configurations

7-Wire Configurations (Standard RS-232C cable) PC RXD TXD GND DTR DSR RTS CTS 8 D-Sub 9 TV 7 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS 3-Wire Configurations(Not standard) PC 8 D-Sub 9 TV 8 D-Sub 9 TXD RXD GND DTR DSR RTS CTS

Set ID

Use this function to specify a set ID number. Refer to Real Data Mapping. G p. 114
Hard of Country Input Label SIMPLINK Key Lock Set ID Set ID Power Indicator Factory Reset

Hearing(

:UK : On : Off

1 Close

Select Set ID.
adjust Set ID to choose the desired TV ID number. The adjustment range of SET ID is 1~99.
Press the RETURN button to move to the previous menu screen.

Communication Parameters

Baud rate : 9600 bps (UART) A Data length : 8 bits A Parity : None
Stop bit : 1 bit A Communication code : ASCII code A Use a crossed (reverse) cable.

Command Reference List

COMMAND COMMAND DATA (Hexadecimal) 01. Power 02. Aspect Ratio 03. Screen Mute 04. Volume Mute 05. Volume Control 06. Contrast 07 Brightness. 08. Colour 09. Tint 10. Sharpness 1 OSD Select 1. 1 Remote control lock mode 2. 1 Balance 3. 1 Colour Temperature 4. 1 Abnormal Status 5. 1 ISM Method 6. 1. Power Saving Auto Configure 8. 19. Equalize 20. Tune Command 21. Channel Add/Skip 22. Key 23. Control Back Light 24. Input select (Main) k k k k k k k k k k k k k k k j j j j m m m m x a c d e f g h i j k l m t u z p q u v a b c g b 00 ~ 01 Refer to p. 00 ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 09 Refer to p. 00 ~ Refer to p. Refer to p. 00 ~ 01 Key Code 00 ~ 64 Refer to p. 1 15
Transmission / Receiving Protocol

Transmission

[Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. * : You can adjust the set ID to choose * [Set ID] desired monitor ID number in option menu. Adjustment range is 1 ~ 99. When selecting Set ID 0, every connected set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/ receiving protocol. : To transmit command data. * [DATA] Transmit FF data to read status of command. : Carriage Return * [Cr] ASCII code 0x0D : ASCII code space (0x20) * [ ]

OK Acknowledgement

[Command2][ ][Set ID][ ][OK][Data][x] * The TV transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
* When setting the 15 ~ 24, a menu does not appear on screen.