42PX5D 42" Plasma Integrated HDTV
LGs Exclusive XD Engine Six distinct processes contribute to picture improvement. LGs XD Engine takes the low resolution of analog signals to near HD levels by improving brightness, contrast, detail and enhancing color as well as reducing signal noise. This total solution results in cinema like high resolution images. Image Sticking Prevention Provides protective measures to minimize damage as a result of stationary images.
ATSC/NTSC/QAM Clear Tuners 9-in-2 Multi Memory Card Slot HDMI with HDCP IEEE 1394 with DTV Link 5000:1 Contrast Ratio 1000 cd/m2 Brightness 1024 x 768p Resolution
Digital Cable Ready (CableCARD) TV Guide On Screen
Video Native Display Resolution 1024 x 768p Contrast Ratio 5000:1 Brightness 1000 cd/m2 Lifetime 60,000 hours Viewing Angle 160 3D Y/C Comb Filter Color Temperature Adjustment 3 Modes Aspect Ratio Adjustment 7 Modes 3:2 Pull-down Cinema Correction 480i EZ Video/Picture Selection Mode 6 Modes High Contrast Screen w/Non-glare Coating Glass Filter XD Engine Enhanced Noise Reduction Black Stretcher Colors 1.07 Billion DTV Signal Strength APM (Adaptive Picture Mode) Audio Audio Output Power Surround System Type Bass/Treble/Balance EZ SoundRite (Volume Leveler) EZ Sound/Sound Selection Mode Speaker System Details BBE 3D EchoSound System Mono/Stereo/SAP 15W x 2 SRS TruSurround XT 5 Modes 2 Way 4 Speaker
Core Features Tuner(s) ATSC/NTSC/QAM Digital Cable Ready (DCR) Memory Card Reader (9 in 2) - 1st slot: CF Type I/II - 2nd slot: MS, MS PRO, SD, MMC, SMC, XD Special Features Custom Channel Labels Custom Input Labels PIP POP Split Screen PIP Exchange/Move Dual Tuner PIP/POP/Split Screen Discrete IR Codes Favorite Channel Selection/Surf Tri-lingual Menus English, Spanish, French On/Off Timer Sleep Timer Auto Off (When no video is present) Flashback (Previous Channel) Parental Control With V-Chip Image Sticking Prevention EZ Menus (High Performance Interface) EZ Scan (Auto Programming) Intelligent Fan Control Program Guide Gemstar IEEE 1394 Software Capability Full AVC Decoder Formats MPEG 2 Closed Caption Child Lock Screen Adjust AV Input Navigation
Audio/Video Inputs/Outputs TV Rear - RF Inputs - S-Video In - Composite Video & Audio L/R In - Composite Video & Audio L/R Out - Component DVD/DTV (480i, 480p, 720p, 1080i) & Audio L/R In - RGB In (PC/DTV Input) - PC Sound (1/8" mini stereo) - HDMI with HDCP - Digital Audio (Optical ) Out - Digital Audio (Optical) In - RS-232c (Software Upgrade Interface & Control) - Remote Control In (IR) - Digital Cable Card Slot - Gemstar Out (G-Link) - IEEE 1394/DTCP TV Left Side - S-Video In - Composite Video & Audio L/R In TV Right Side - EPF Slot Dimensions Cabinet Dimensions without Stand - Width x Height x Depth - Weight Out of Package Cabinet Dimensions with Stand - Width x Height x Depth - Weight Out of Package Dimensions with Packaging - Width x Height x Depth - Weight In Package Power Consumption UPC Warranty Remote Control Standard IR Wired Option Universal Backlit
Cabinet/Accessories Cabinet Style Cabinet Color Table Stand Included Speakers Included (Not Detachable) Front Lighted Display (LED)

Table Top Black Index

49.3 x 27.8 x 1 1.16.1 lbs.
49.3 x 25.7 x 4.0 99.8 lbs.
52.8 x 30.3 x 15.0 127.8 lbs. 450W year parts/labor

TV Rear

CABLE CARD

RS-232c INPUT

TV Left Side

S-VIDEO

(R) - AUDIO - (L)

9-in-2 MEMORY CARD

TV Right Side

G-LINK

IEEE 1394

HDMI 2

HDMI 1/DVI
COMPONENT 2 INPUT DVI INPUT

OUTPUT

DIGITAL AUDIO (OPTICAL)

RGB IN (PC/DTV INPUT)

PC AUDIO INPUT
(480i, 480p, 720p, 1080i) (480i, 480p, 720p, 1080i) COMPONENT 2

COMPONENT 1

(L) AUDIO (R)

OUTPUT INPUT A/V

REMOTE IN

CABLE IN +75 |

ANT IN +75 |

AC INPUT

LG Electronics U.S.A., Inc.
1000 Sylvan Avenue Englewood Cliffs, NJ 07632 www.LGusa.com
Design and specifications subject to change without notice. 03/23/05
2005 LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. LG Design and Lifes Good are trademarks of LG Electronics, Inc. All other trademarks are the property of their respective owners.

PWMT300

Model: PWMT300
Installation and Assembly: Universal Wall Mount
This product is UL Listed. It must be installed by a qualified professional installer.

Features:

For flat panel screens One-touch tilt for effortless positioning and adjustment of the screen Ultra-slim design holds the screen flat against the wall IncreLok locking tilt positions for specific tilt settings in 5 increments BLACK. Scratch resistant fused epoxy finish. Mounts to wood studs, concrete, or to cinder blocks
Max UL Load Capacity 250lb (113.5kg)
NOTE: Not for use with metal studs

1 of 14

Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 12-15-06 SHEET #:202-9189-1
For customer care call 1-800-865-2112 or 708-865-8870.
Note: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install this mount until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Never exceed the Maximum UL Load Capacity. See page one. If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
Tools Needed for Assembly
stud finder ("edge to edge" stud finder is recommended) drill 1/4" bit for concrete and cinder block wall 5/32" bit for wood stud wall level 7/16" socket or crescent wrench tape measure

Table of Contents

Parts List...... 3 Adjusting Tilt Brackets...... 4 Installing Tilt Brackets..... 5 Installation to Double Wood Stud Wall..... 7 Installation to Triple Wood Stud Wall.... 8 Installation to Solid Concrete or Cinder Block.... 9 Mounting and Removal of Flat Panel Screen.... 10 Screen Compatibility Chart..... 11
For customer care call (800) 729-0307 or (708) 865-8870.

2 of 14

ISSUED: 12-15-02 SHEET #:202-9189-1
Before you begin, make sure all parts shown are included with your product. Parts may appear slightly different than illustrated.

Parts List

AA BB CC DD EE FF GG HH II Description wall plate left tilt bracket right tilt bracket #14 x 2.5 wood screw alligator anchor 1/4 serrated flanged locknut wing bracket M5 x 25mm security screw wrench Qty. 1 Black Part # 201-1210 201-0181 201-0177 5S1-015-C03 590-0097 530-1021 201-1134 520-1122 560-1146 Silver Part# 201-4210 201-0192 201-0193 5S1-015-C03 590-0097 530-1021 201-4134 520-1122 560-1146

top extension bracket

FF Security Option
NOTE: Replace safety screw in each tilt bracket with M5 x 25 security screw (HH) using wrench (II).

bottom extension bracket

Adapter Bracket Fasteners
M4 x 8 mm (6) (520-1237) M4 x 12 mm (6) (504-9013)
M5 x 12 mm (4) (520-1027) M5 x 25 mm (4) (520-9543) M4 x 25 mm (4) (504-1015) M5 x 40 mm (6) (520-1199) multi-washer (6) (580-1036) I.D. 5.6 mm (4) (540-1057)
M6 x 12 mm (4) (520-1128)
M6 x 16 mm (6) (520-9274)
M8 x 16 mm (6) (520-9257)
M8 x 25 mm (4) (520-1031)
I.D. 6.4 mm (6) (590-1106)
I.D. 8.7 mm (4) (540-1059)
Parts may appear slightly different than illustrated. 3 of 14
Adjustment of Extension Brackets
Loosen four 1/4-20 x 1/4" screws on each adapter bracket (BB,CC). Position extension brackets, with slots facing downward, onto adapter brackets (BB,CC) at the appropriate position to accommodate your screen as shown in Figure 1.1. Securely tighten all 1/4-20 x 1/4" screws as shown in figure 1.2. NOTE: In all bracket extension positions, stops and 1/4-20 x 1/4" screws must be engaged in slots as shown in figure 1.2.

TOP EXTENSION BRACKET

ADAPTER BRACKET

TIGHTEN FASTENERS

1/4-20 x 1/4" SCREWS

BOTTOM EXTENSION BRACKET

Make sure slots face downward.

fig 1.1

fig 1.2

4 of 14

Installing Tilt Brackets
Refer to Screen Compatibility Chart to determine the proper fasteners to use. NOTE: Refer to page 4 for adjustments of top extension bracket. To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place tilt brackets (BB and CC) on back of screen. Align to holes, and center on back of screen as shown in figure 2.1. Attach the tilt brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in figure 2.3. NOTE: Be sure to attach tilt brackets with knobs facing outward as in figure 2.1. NOTE: Top and bottom mounting holes must be used for attaching brackets. Middle holes should also be used where the fasteners and screens allow. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.

Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. lb (4.5 N.M.) maximum torque. If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
CENTER BRACKETS VERTICALLY ON BACK OF SCREEN

KNOBS FACE OUT

fig 2.1
Note: "X" dimensions should be equal.
NOTES: Always use multi-washers when attaching tilt brackets (BB and CC) to your screen. Use the corresponding hole in the multiwasher that matches your screw size as shown in figure 2.2. Spacers may not be used, depending upon the type of screen.
MULTI-WASHER MEDIUM HOLE FOR M5 SCREWS SMALL HOLE FOR M4 SCREWS LARGE HOLE FOR M6 SCREWS

fig. 2.2

SPACER

fig 2.3

MULTIWASHER

5 of 14

With tape measure, measure the outside to outside of the brackets on the back of your screen. If width of the tilt brackets on back of the screen is over 18-1/2" shown in figure 3.1, using a wrench, attach wing bracket (GG) to center bracket using two 1/4 serrated flanged locknuts (FF) as shown in figure 3.2. If width of the brackets on back of the screen is over 30-3/8", using a wrench, attach second wing bracket (GG) to center bracket using two 1/4 serrated flanged locknut (FF) as shown in figure 3.3. CAUTION: If mounting to two studs on 16" centers, and using the three plate configuration, A STUD MUST BE SKIPPED in the middle so distance between studs is 32". 18.5"

fig. 3.1

fig. 3.2

fig. 3.3

6 of 14
Installation to Double Wood Stud Wall
Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. NOTE: If mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. Skip to page 8 Wall plate (AA) can be mounted to two studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each studs center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.1. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using four #14 x 2.5" wood screws (DD) as shown in figure 4.2. NOTE: Wall plate may be mounted up to 4" (102 mm) off center as shown in figure 4.1. Skip to step 5.

4" (102 mm)

2.5" (64 mm)

CS = center of screen

fig. 4.1

fig. 4.2

7 of 14
Installation to Triple Wood Stud Wall
Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.). Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended. Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations. Wall plate (AA) can be mounted to three studs that are 16" apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each studs center. Place wall plate on wall as a template. The top mounting slots should be 2.5" above the desired screen center as shown in figure 4.3. Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws (DD) as shown in figure 4.4. NOTE: When mounting equipment weighing greater than 200 lbs, triple stud mounting is strongly recommended. If mounting to two studs on 16" centers, leave an open stud in center. Wall plate may be mounted up to 4" (102 mm) off-center as shown in figure 4.3. Skip to step 5.
4" 4" (102 mm) (102 mm)

fig. 4.3

fig. 4.4

8 of 14

Installation to Solid Concrete or Cinder Block
When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. Make sure that wall plate (AA) is level, use it as a template to mark four mounting holes. The top mounting hole should be 2.5" above the desired screen center as shown in figure 4.1 on page 7. Drill four 1/4" (6 mm) dia. holes to a minimum depth of 2.5" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws (DD). Level, then tighten all fasteners. NOTE: Six holes and six sets of fasteners are required when mounting the wall plate for equipment weighing greater than 200 lbs.

concrete surface

Drill holes and insert anchors (EE).

AA DD EE

Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. Never tighten in excess of 80 in. lb (9 N.M.).
Place plate (AA) over anchors (EE) and secure with screws (DD).
Always attach concrete anchors directly to loadbearing concrete. Never attach concrete anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. (Not evaluated by UL)

INCORRECT

CUTAWAY VIEW
wall plate concrete wall plate

Tighten all fasteners.

so lid co nc ret e

CORRECT

concrete

plaster/ dry wall

9 of 14
Mounting and Removing Flat Panel Screen
Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. NOTE: For security, replace safety screw in each tilt bracket with M5 x 25 security screw (HH) using wrench (II).

BB and CC AA AA

SAFETY Adjust brackets to full back tilt position and tighten. SCREW Hook tilt brackets (BB and CC) onto wall plate (AA). Then slowly swing screen in as shown. Turn safety screws, using wrench (II), clockwise till fully tightened down and screw tip securely contacts bottom of the wall plates as shown in detail 1. of figure 5.1. Center of screen can be adjusted horizontally no more than 4" from center of the wall plate configuration, if desired as shown in figure 5.2.

DETAIL 1 fig 5.1

4"
NOTE: To lock the screen down, tighten safety screws to wall plate using using wrench (II) as shown in detail 1. To remove screen from mount, loosen safety screws, swing screen away from mount, and lift screen off of mount.

CAUTION

Do not tighten screws with excessive force. Overtightening can cause damage to mount. Tighten screws to 40 in. lb (4.5 N.M.) maximum torque.
Be careful not to pinch fingers when pushing screen from the bottom.

fig 5.2

Adjusting the Tilt Angle of the Flat Panel Screen

LOCATOR HOLE TENSION

KNOB Adjust tension knobs shown in detail 2 to desired tension, balancing your screen size and weight. The tension knob, without changing the bracket tension, can be pulled out, away from the bracket and turned TILT POSITION HOLES independently of the knob post for readjustment as shown in Detail 3.

DETAIL 2

IncreLok TILT LOCKING SCREW
Push or pull from top or bottom of screen to adjust tilt as shown in figure 6.1. The tilt can be adjusted to a maximum of 15 forward or 5 backward. NOTE: To lock the screen into the desired tilt position, use locator hole to find tilt position hole. Tighten IncreLok tilt locking screws on both tilt brackets as shown in figure 6.1 and detail 2.

TENSION KNOB

fig 6.1 DETAIL 3

10 of 14

See chart below to determine the fasteners to use with your screen. If your screen has a note in the far right column, then reference it on the last page. PWMT300
Manufacturer LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG
ScreenSize 23" 23" 23" 23" 23" 23" 23" 23" 26" 26" 26" 26" 26" 26" 27" 27" 30" 30" 30" 30" 30" 30" 30" 32" 32" 32" 32" 32" 32" 32" 32" 32" 32" 37" 37" 37" 37" 37" 37" 37" 37" 37" 37" 37" 37" 40" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42" 42"
Model 23LX1R 23LX2R 23LXRV L2320A L2323T RU-23LZ21 RU-23LZ50C Z23L6R 26LX1D 26LX2D L26W56SA RM-26LZ30 RU-26LZ30 Z26LZ5R RU-26LZ50 RU-27LZ50C DU-30LZ30 L3000A L3000H L3020T RL-30LZ50 RZ-30LZ50 RU-30LZ50C 32LC2D L3200A L3200AK L3200T L3200TC L3200TK RU-32LZ30C RU-32LZ50C L3200A L3200AK 37LB1DA 37LP1D DU-37LZ30 DU-37LZ30C L3700A L3700AK L3700T L3700TC L3700TK M3700C-BA M3701C 37LB1DA MU-40PA10B 42LB1DR 42LB1DRA 42LC2D 42PC1DA 42PC3D 42PC3DV 42LP1DC 42PM1M 42PX10 42PX20 42PX3DBV 42PX3DLV 42PX3DCV 42PX4D 42PX5D 42PX7DC DU-42LZ30 DU-42PX10C DU-42PX11 DU-42PX12X DU-42PX12XC DU-42PX12XD DU-42PY10
ScrewSize M4 M4 M4 M4 M4 M4 M4 M4 M4 M4 M6 M4 M4 M4 M4 M4 M4 M5 M4 M4 M4 M4 M4 M4 M6 M6 M4 M4 M4 M4 M4 M6 M6 M8 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5

ScrewLength / 40 25

washer multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi none none multi multi multi multi multi multi multi none multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi
Spacer none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none none 8.7mm ID none 5.6mm ID 5.6mm ID none none none none none none none none 5.6mm ID none none none none none none none none 5.6mm ID 5.6mm ID 28.6mm tall 28.6mm tall 5.6mm ID 5.6mm ID 5.6mm ID none 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID

12 of 14

Manufacturer LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG LG
ScreenSize 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 50" 55" 55" 60" 60" 60" 60" 60" 60" 60" 60" 60" 60" 60" 60" 60" 60" 71"
Model 50PC1DRA 50PC3D 50PM1M 50PX1D 50PX10 50PX20 50PX4DR-H 50PX5D 50PY20 DU-50PM10C DU-50PX10C DU-50PY10 DU-50PZ60 DU-50PZ60H MU-50PM10/11 MU-50PZ41 MU-50PZ41B MU-50PZ41V MU-50PZ90C MU-50PZ90V RU-50PZ61 50PC1DR 50PC1DRA 50PC3D 50PM1M 50PX1D 50PX10 50PX20 50PX4DR-H 50PX5D 50PY20 DU-50PM10C DU-50PX10C DU-50PY10 DU-50PZ60 DU-50PZ60H MU-50PM10/11 MU-50PZ41 MU-50PZ41B MU-50PZ41V MU-50PZ90C MU-50PZ90V RU-50PZ61 55LP1M M5500C-BA DU-60PY10 DU-60PZ60 MU-60PZ10 MU-60PZ12 MU-60PZ90C MU-60PZ90V MU-60PZ95V DU-60PY10 DU-60PZ60 MU-60PZ10 MU-60PZ12 MU-60PZ90C MU-60PZ90V MU-60PZ95V MW-71PY10
ScrewSize M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M5 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8 M8

ScrewLength 16 16

washer multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi multi none none none none none none none none none none none none none none none
Spacer none none 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID none none none 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID 5.6mm ID none none none none none none none none none none none none none none none none none

13 of 14

NOTES (only pertains to the screen specified in the configuration chart) * The mount includes 12.7mm tall spacers 1 All hardware may not be included. If you are missing the additional fasteners needed for your screen, then please contact Customer Care at 1-800-865-2112. 2 If back of screen has a bumpout, or if mounting holes lie in pockets, then use M4 X 25 mm screw with 12.7mm tall spacers 3 If screw gets less than 3 threads of engagement, then try the next longer length screw. If all longer lengths have been tried, and there is still less than 3 threads of engagement, then contact Customer Care for assistance. 4 If back of screen has a bumpout, remove it, or use the 15.9mm tall spacer and stack that with the 12.7mm spacer to give you the 28.6mm spacing. 5 For top mounting holes use M5 x 25 mm screws with 5.6mm ID spacers, for bottom mounting holes use M5 x 40mm screws with 5.6mm ID spacers in both cases.

14 of 14

2006 Peerless Industries, Inc. All rights reserved. All other brand and product names are trademarks or registered trademarks of their respective owners.