PLASMA TV Models : 42/50PG20**, 42/50/60PG30**
Remote Control Sensor POWER
Power/Standby Indicator illuminates red in standby mode. illuminates green when the TV is switched on.

MENU INPUT

OK MENU

P VOLUME

PROGRAMME
PLASMA TV Models : 42/50PG10**
Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates green when the TV is switched on.

VOLUME

LCD TV Models : 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42/47/52LG5***
POWER Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates blue when the TV is switched on. Note: You can adjust Power Indicator in
Intelligent Sensor Adjusts picture according to the surrounding conditions. (32/37/42/47/52LG5*** only)

the OPTION menu.

Attaching the TV to a desk (Only 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. Stand
1-Screw (provided as parts of the product) Desk

! WARNING

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
LCD TV Models : 19/22LG30**
INPUT MENU OK VOLUME PROGRAMME

INPUT MENU OK

POWER Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates blue when the TV is switched on. Note: You can adjust Power Indicator in the OPTION
LCD TV Models : 19/22LS4D*
POWER INPUT MENU OK VOLUME PROGRAMME

BACK PANEL INFORMATION

Image shown may differ from your TV.

S-VIDEO

PLASMA TV Models : 42/50PG10**, 42/50PG20**, 42/50/60PG30**

VIDEO L/MONO AUDIO R

AV IN 3

To connect additional equipment, see the E x t e r n a l E q u i p m e n t S e t u p section.
Install the C A B L E M A N A G E M E N T C L I P as shown. If your TV has the CABLE HOLDER, install it as shown and bundle the cables.

(Only 42/50PG10**)

(Only 42/50PG20**, 42/50/60PG30**)

CABLE HOLDER

CABLE MANAGEMENT CLIP
How to remove the cable management clip
Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward. * For the 42PG10** model, press the center of the CABLE MANAGEMENT CLIP and then lift up it.
LCD TV Models: 32/37/42LG20**, 26/32/37/ 42LG30**, 32/42LG32**, 32/37/42/47/52LG5***
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. Open the C A B L E M A N A G E M E N T C L I P as shown and manage the cables.
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section.
Install the CABLE MANAGEMENT CLIP as shown.
Fit the C A B L E M A N A G E M E N T C L I P as shown.
How to remove the cable management clip (LCD TV Models : 19/22LS4D*)
First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward.
G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.
To connect additional equipment, see the External Equipment Setup section of the manual.
Hold the CABLE MANAGEMENT CLIP with both hands and pull it backward.
POSITIONING YOUR DISPLAY (Only 19/22LG30**, 19/22LS4D*)

Tilt range

Image shown may differ from your TV. Adjust the position of the panel in various ways for maximum comfort.
LOCATION (Only 19/22LG30**, 19/22LS4D*)
Position your TV so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the tv to any unnecessary vibration, moisture, dust or heat. Also ensure that the TV is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover. If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV. When you install the TV to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
KENSINGTON SECURITY SYSTEM (Only 19/22LG30**, 19/22LS4D*)
The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington Security System cable as shown below. For the detailed installation and use of the Kensington Security System, refer to the users guide provided with the Kensington Security System. For further information, contact http://www.kensington.com, the internet homepage of the Kensington company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD projectors. NOTE - The Kensington Security System is an optional accessory. NOTES a. If the TV feels cold to the touch, there may be a small flicker when when it is turned on. This is normal, there is nothing wrong with TV. b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV.

4 inches

WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
4 inches 4 inches 4 inches 4 inches
Not using the desk-type stand
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the P R O T E C T I O N C O V E R into the TV until clicking sound.

< PLASMA TV >

< LCD TV >
To prevent damage do not connect to the mains outlet until all connections are made between the devices.

ANTENNA CONNECTION

For optimum picture quality, adjust antenna direction. An antenna cable and converter are not supplied.

Wall Antenna Socket

Multi-family Dwellings/Apartments (Connect to wall antenna socket)
HDMI IN RGB IN ANTENNA IN

VIDEO AUDIO

VARIABLE AUDIO OUT

RF Coaxial Wire (75 ohm)

Outdoor Antenna (VHF, UHF)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Antenna

Signal Amplifier
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above. If signal needs to be split for two TVs, use an antenna signal splitter for connection.
To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment. This section on EXTERNAL EQUIPMENT SETUP mainly uses diagrams for the 22LS4D* models.

HD RECEIVER SETUP

This TV can receive Digital RF/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the diagram as shown below.
Connecting with a component cable

EXTERNAL EQIPMENT SETUP

Connect the video outputs (Y, PB, PR) of the digital set top box to the C O M P O N E N T I N V I D E O jacks on the TV. Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O jacks on the TV.
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select C o m p o n e n t input source using the I N P U T button on the remote control. Signal Component Yes Yes Yes Yes

(50/60Hz)

HDMI No Yes Yes Yes
480i/576i 480p/576p 720p/1080i 1080p
Connecting a set-top box with an HDMI cable
Connect the HDMI output of the digital set-top box to the H D M I / D V I I N, H D M I / D V I I N 1, H D M I I N 2 or H D M I I N 3 jack on the TV. Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI/DVI, HDMI1, HDMI2 or HDMI3 input source using the I N P U T button on the remote control.
Connecting with a HDMI to DVI cable
Connect the digital set-top box to H D M I / D V I I N, H D M I / D V I I N 1 ( D V I ) or H D M I / D V I I N 1 jack on the TV. Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I ) jack on the TV.
Turn on the digital set-top box. (Refer to the owners manual for the digital set-top box.) Select HDMI/DVI or HDMI 1 input source using the I N P U T button on the remote control.

DVI-PC OUTPUT

DIGITAL AUDIO OUT SETUP
- Sending the TVs audio signal to external audio equipment via the Digital Audio Output (Optical) port.
Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.

DVI IN

Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. Set the TV Speaker option - Off in the AUDIO menu. (G p.80) Refer to the external audio equipment instruction manual for operation.

RETURN(EXIT) Allows the user to move back one step in an interactive application, EPG or other user interaction function. INFO i Shows the present screen information. AV MODE It helps you select and set images and sounds when connecting AV devices. Coloured These buttons are used for teletext (on T E L E T E X T buttons models only) , P r o g r a m m e e d i t. TELETEXT These buttons are used for teletext. BUTTONS For further details, see the Teletext section. SUBTITLE Recalls your preferred subtitle in digital mode.
See a list of AV devices connected to TV. When you toggle this button, the Simplink menu appears at the screen.
VOLUME UP Adjusts the volume. /DOWN FAV Displays the selected favourite programme. MUTE Switches the sound on or off. Programme Selects a programme. UP/DOWN PAGE Move from one full set of screen information to the next UP/DOWN one. 0~9 number Selects a programme. button Selects numbered items in a menu. LIST Displays the programme table. Q.VIEW Returns to the previously viewed programme.
SIMPLINK Controls simplink. control buttons

TURNING ON THE TV

- When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode.
In standby mode to turn TV on, press the r / I, INPUT or P (or PR D E) button on the TV or press the POWER, INPUT, D/A, P (or (PR + - or P + -)) or NUMBER button on the remote control and the TV will switch on.
Initializing setup If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the Language, Select Mode, Country, Time Zone, Auto programme tuning.
Note: a. It will automatically disappear after approx. 40 seconds unless a button is pressed. b. Press the RETURN button to change the current OSD to the previous OSD. c. For those countries without confirmed DTV broadcasting standards, some DTV features might not work, depending on the DTV broadcasting environment. d. "Home mode is the optimal setting for home environments, and is the TV's default mode. e. "In Store" mode is the optimal setting for store environments. If a user modifies image quality data, In Store mode initializes the product to the image quality set by us after a certain period of time. f. The mode (Home, In Store) can be changed by executing Factory Reset in the OPTION menu.

Intelligent Sensor 100 Vivid 100 Standard 50 Cinema 70 Sport 70 Game ExpertExpert1 Expert2
Backlight Contrast Brightness Sharpness Colour Tint Expert Control Control Picture Reset
100 Contrast Fresh Noise 70 Reduction Gamma 50 Black 50 Level Film Mode 50 Colour Standard 0
White Balance Red Contrast
Off Off Medium High On SD Warm 0
PICTURE IMPROVEMENT TECHNOLOGY
Fresh Contrast Optimizes the contrast automatically according to the brightness of the reflection. Fresh Colour Adjusts the colour of the reflection automatically to reproduce as close as possible natural colours. Noise Reduction Removes interference up to the point where it does not damage the original picture.
Gamma High gamma values display whitish images and low gamma values display high contrast images.
Colour Temperature Fresh Contrast Fresh Colour Noise Reduction Gamma Black Level Eye Care Film Mode Close
Select Fresh Contrast, Fresh Colour, Noise Reduction or Gamma.

ADVANCED - FILM MODE

To set the TV up for the best picture quality for viewing films. This feature operates only in TV, AV and Component 480i/576i/1080i mode.

Select Film Mode.

ADVANCED - BLACK(DARKNESS) LEVEL
When you view a film this function adjusts the TV to best picture quality. This function works in the following mode: AV (NTSC-M), HDMI or Component.
L o w : The reflection of the screen gets darker. H i g h : The reflection of the screen gets

brighter.

A u t o : Realizing the black level of the screen
and set it to High or Low automatically.

Select Black Level.

Select Low or High.

EYE CARE (LCD TV ONLY)

It helps you adjust brightness when the screen is too bright to prevent dazzling.

Select Eye Care.

PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
Backlight 100 Contrast 100 Brightness 50 Sharpness 70 Colour 70 Tint 0 Advanced Control Picture Reset
Backlight 100 Contrast 100 Brightness 50 Sharpness video 70 i Resetting configuration. Colour 70 R Tint 0 Advanced Control Picture Reset

Select TV Speaker.

SELECTING DIGITAL AUDIO OUT
This function allows you to select your preferred Digital Audio Output. The TV can only output DOLBY Digital if a channel is broadcast with Dolby Digital audio. When Dolby digital is available, selecting Dolby Digital in the Digital Audio Out menu will set SPDIF output to Dolby Digital If Dolby Digital is selected in the digital audio out menu when dolby digital is not available, SPDIF output will be PCM. Even if both Dolby Digital and Audio language have been set in a channel which broadcast Dolby Digital Audio, only Dolby Digital will be played.
500Hz 1.2KHz 3KHz 7.5KHz 12KHz Reset Digital Audio Out : PCM Digital Audio Out PCM TV Speaker : Off

OK + + +

Dolby Digital PCM PCM
Select D i g i t a l A u d i o O u t.
Select D o l b y D i g i t a l or P C M.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. There is a possibility that when HDMI mode, some DVD players do not make SPDIF sound. At that time, set the output of the digital audio of the DVD player to PCM.

AUDIO RESET

Settings of the selected Sound Mode return to the default factory settings.

OK + + + + + + +

120Hz 200Hz 500Hz 1.2KHz 3KHz 7.5KHz 12KHz Reset Reset
+ 120Hz 0 + 200Hz 0 + 500Hz 0 1.2KHz 0 i Resetting sound mode configuration. 3KHz 0 + 7.5KHz 0 + 12KHz 0 Reset Reset
Stereo/Dual Reception (In Analogue Mode Only)
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.

For 19/22LS4D* only

Select the sound output.
Broadcast Mono Stereo Dual

On Screen Display

MONO STEREO DUAL I, DUAL II, DUAL I+II
Mono sound selection If the stereo signal is weak in stereo reception, you can switch to mono. In mono reception, the clarity of sound is improved. Language selection for dual language broadcast If a programme can be received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II.

DUAL I DUAL II DUAL I+II

Sends the primary broadcast language to the loudspeakers. Sends the secondary broadcast language to the loudspeakers. Sends a separate language to each loudspeaker.
NICAM Reception (In Analogue Mode Only)
If the TV is equipped with a receiver for NICAM reception, high quality NICAM (Near Instantaneous Companding Audio Multiplex) digital sound can be received. Sound output can be selected according to the type of broadcast received.

When NICAM mono is received, you can select N I C A M M O N O or F M M O N O.
When NICAM stereo is received, you can select N I C A M S T E R E O or F M M O N O. If the stereo signal is weak, switch to F M m o n o.
When NICAM dual is received, you can select N I C A M D U A L I, N I C A M D U A L I I or N I C A M D U A L I + I I or F M M O N O.
Speaker Sound Output Selection
In AV, Component, RGB and HDMI mode, you can select output sound for the left and right loudspeakers.
L+R: Audio signal from audio L input is sent to the left loudspeaker and audio signal from audio R input is sent to the right loudspeaker. L+L: Audio signal from audio L input is sent to left and right loudspeakers. R+R: Audio signal from audio R input is sent to left and right loudspeakers.
ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
Select your desired language.

Select your country.

* If you want to change Language/ Country selection
Select Menu Language or Country.
Select your desired language or country.

G G G G G

If you do not finish the set-up Installation Guide by pressing RETURN or if you time out on the OSD (On Screen Display) the installation menu will continuously appear until the set up is completed whenever the TV is switched on If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. The CI (Common Interface) function may not be applied based on country broadcasting circumstances. DTV mode control buttons may not function based on country broadcasting circumstances. In country that Digital broadcasting regulation isnt fixed, some DTV function may not work depending on digital broadcasting circumstances. The Country Setting UK should only be activated UK.
LANGUAGE SELECTION (IN DIGITAL MODE ONLY)
The Audio function allows selection of a preferred language. If audio data in a selected language is not broadcast, the default language audio will be played. Use the Subtitle function when two or more subtitle languages are broadcast. If subtitle data in a selected language is not broadcast, the default language subtitle will be displayed. When the languages you selected as the primary for Audio Language and Subtitle Language are not supported, you can select language in secondary category.

SPECIAL TELETEXT FUNCTIONS
button to select the Text Option menu.

A REVEAL

Select this menu to display concealed information, such as solutions to riddles or puzzles.

A UPDATE

Displays the TV picture on the screen while waiting for a new teletext page. The display will appear at the top left hand corner of the screen. When the updated page is available then display will change to the page number. Select this menu again to view the updated teletext page.

A TIME

When viewing a TV programme, Select this menu to display the time at the top right hand corner of the screen. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or change the sub page, press the RED/GREEN, or NUMBER buttons.

A HOLD

Stops the automatic page change which will occur if a teletext page consists of 2 or more sub pages. The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this menu is selected the stop symbol is displayed at the top left-hand corner of the screen and the automatic page change is inactive.
*This function works in UK only.
The TV gives you access to digital teletext which is greatly improved in various aspects such as text, graphics etc. This digital teletext can access special digital teletext services and specific services which broadcast digital teletext. You should select off in the subtitle language menu to display teletext by pressing the SUBTITLE button.
TELETEXT WITHIN DIGITAL SERVICE
Press the numeric or P (or (PR + - or P + -)) button to select a digital service which broadcasts digital teletext. To know which are digital teletext services, refer to the EPG service list. Follow the indications on digital teletext and move onto the next step by pressing TEXT, OK, , RED, GREEN, YELLOW, BLUE or NUMBER buttons and etc. To change digital teletext service, select a different service by the numeric or P (or (PR + - or P + -)) button.
TELETEXT IN DIGITAL SERVICE
Press the numeric or P (or (PR + - or P + -)) button to select a certain service which broadcasts digital teletext. Press the TEXT or coloured button to switch on teletext. Follow the indications on digital teletext and move onto the next step by pressing OK, , RED, GREEN, YELLOW, BLUE or NUMBER buttons and so on. Press the TEXT or colour button to switch off digital teletext and return to TV viewing. Some services may allow you to access text services by pressing the RED button.

Cleaning the Screen

A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Do not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to protect against possible damage from lightning or power surges.

PRODUCT SPECIFICATIONS

MODELS 42PG10** 42PG1000-ZA with stand without stand with stand without stand Power requirement Power Consumption MODELS
1040.0 x 729.0 x 308.0 mm 41.0 x 28.7 x 1 inches 2.2 1040.0 x 677 x 84.0 mm.0 41.0 x 26.7 x 3.3 inches 26.6 kg / 58.7 lbs 24.6 kg / 54.3 lbs AC100-240V~ 50/60Hz 3.1A 310W

50PG10** 50PG1000-ZA

1 224.7 x 849.0 x 364.0 mm 48.3 x 33.5 x 1 inches 4.224.7 x 790.0 x 83.6 mm 48.3 x 31.1 x 3.3 inches 41.5 kg / 91.5 lbs 38.1 kg / 84.0 lbs AC100-240V~ 50/60Hz 4.2A 420W

42PG30** 42PG3000-ZA

1039.5 x 726.0 x 307 mm.6 41.0 x 28.6 x 1 inches 2.1 1039.5 x 673.7 x 84.0 mm 41.0 x 26.6 x 3.3 inches 28.0 kg / 61.8 lbs 25.0 kg / 55.1 lbs AC100-240V~ 50/60Hz 3.1A 310W

Dimensions

(Width x Height x Depth)

Weight

50PG30** 50PG3000-ZA

42PG20** 42PG2000-ZA

1040 x 731.3 x 308 mm 40.9x 28.7 x 1 inches 2.x 677 x 86 mm 40.9 x 26.6 x 3.4 inches 27 kg / 60.1 lbs.3 24.4 kg / 53.8 lbs AC100-240V~ 50/60Hz 3.1A 310W

50PG20** 50PG2000-ZA

1 224.7 x 849 x 364 mm 48.2 x 33.4x 1 4.3inches 1 224.7 x 790 x 86 mm 48.2x 31.1 x 3.4 inches 41.8 kg / 92.2 lbs 37.8kg / 83.3lbs AC100-240V~ 50/60Hz 4.2A 420W
with stand without stand with stand without stand
1 232.0 x 850.0 x 363.6 mm 48.5 x 33.5 x 1 inches 4.232.0 x 793.0 x 84.0 mm 48.5 x 31.2 x 3.3 inches 42.3 kg / 93.3 lbs 38.3 kg / 84.5 lbs AC100-240V~ 50/60Hz 4.2A 420W
Weight Power requirement Power Consumption

MODELS

60PG30** 60PG3000-ZA

19LS4D* 19LS4D-ZD

456.8x 396.6x 1 72.0 mm 1 x 1 x 6.8 inches 8.0 5.6 456.8 x 368.5 x 70.5 mm 1 x 1 x 2.8 inches 8.0 4.5 1.3 5.1 kg / 1 lbs 4.6 kg / 10.2 lbs AC100-240V~ 50/60Hz 0.8A 50W

22LS4D* 22LS4D-ZD

525.4 x 441.7x 1.4 mm 87 20.7 x 1.4 x 7 inches 7.3 525.4 x 41 68.6 mm 3x 20.7 x 1 x 2.7 inches 6.3 6.1 kg / 1 lbs 3.5 5.7 kg / 1 lbs 2.6 AC100-240V~ 50/60Hz 1.0A 60W
x 1009.1 x 41 mm 3.x 39.7 x 1 inches.8 6.468 x 949.5 x 88.5 mm 57 x 37 x 3.5 inches.8.4 80.6 kg / 1.7 lbs 77 72.6 kg / 1 60.1 lbs AC100-240V~ 50/60Hz 5.6A 560W
Television System Programme Coverage External Antenna Impedance Operating Temperature Operating Humidity Environment condition Storage Temperature Storage Humidity
PAL/SECAM B/G/D/K, PAL I/II, SECAM L/L VHF: E2 ~ E12, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S0 ~ 40C / 32 ~ 104F Less than 80% -20 ~ 60C / -4 ~ 140F Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
19LG30** MODELS 19LG3000-ZA 19LG3050-ZA 19LG3060-ZB
458.8 x 391.0 x 1 89.2 mm 1 x 1 x 7 inches 8.1 5.4.5 458.8 x 344.5 x 69.0 mm 1 x 1 x 2.7 inches 8.1 3.6 5.02 kg / 1 lbs 1.1 4.76 kg / 10.5 lbs AC100-240V~ 50/60Hz 0.8A 50W
22LG30** 22LG3000-ZA 22LG3050-ZA 22LG3060-ZB
522.2 x 431.5 x 1 89.0 mm 20.6 x 1.0 x 7 inches 7.5 522.2 x 384.2 x 69.0 mm 20.6 x 1 x 2.7 inches 5.2 5.6 kg / 1 lbs 2.4 5.34 kg / 1 lbs 1.8 AC100-240V~ 50/60Hz 0.9A 55W
26LG30** 26LG3000-ZA 26LG3050-ZA
663.3 x 508.2 x 227 mm.3 26.1 x 20.1 x 9.0 inches 663.3 x 449.8 x 80.0 mm 26.1 x 1.8 x 3.2 inches 7 10.1 kg / 22.3 lbs 8.6 kg / 19.0 lbs AC100-240V~ 50/60Hz 1.2A 1 20W
32LG30** MODELS 32LG3000-ZA 32LG3030-ZA
801.8 x 604.2 x 227 mm.3 31.6 x 23.8 x 9.0 inches 801.8 x 544.1 x 79.0 mm 31.6 x 21.5 x 3.2 inches 1 kg / 29.6 lbs 3.kg / 26.3 lbs 1.9 AC1 00-240V~50/60Hz 1.5A 1 50W
37LG30** 37LG3000-ZA 37LG3030-ZA
42LG30** 42LG3000-ZA 42LG3030-ZA

32LG20** 32LG2000-ZA

919.6 x 682.3 x 293.8 mm 1032.8 x 742.3 x 293.8 mm 40.7 x 29.3 x 1 inches 1.6 36.2 x 26.9 x 1 inches 1.x 610.3 x 89.0 mm 9.6 36.2 x 24.0 x 3.5 inches 1 kg / 41.5 lbs 8.kg / 35.7 lbs 6.2 1032.8 x 670.1 x 92.0 mm 40.7 x 26.4 x 3.7 inches 23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs
AC1 00-240V~50/60Hz 1.8A AC1 00-240V~50/60Hz 2.3A 1 80W 230W

37LG20** 37LG2000-ZA

42LG20** 42LG2000-ZA

32LG32** 32LG3200-ZA

801.8 x 604.2 x 227 mm.3 31.6 x 23.8 x 9.0 inches 801.8 x 544.1 x 79.0 mm 31.6 x 21.5 x 3.2 inches 1 kg / 29.6 lbs 3.kg / 26.3 lbs 1.9

42LG32** 42LG3200-ZA

1032.8 x 742.3 x 293.8 mm 40.7 x 29.3 x 1 inches 1.6 1032.8 x 670.1 x 92.0 mm 40.7 x 26.4 x 3.7 inches 23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs
91 x 682.3 x 293.8 mm 1032.8 x 742.3 x 293.8 mm 9.6 36.2 x 26.9 x 1 inches 40.7 x 29.3 x 1 inches 1.6 1.6 919.6 x 610.3 x 89.0 mm 36.2 x 24.0 x 3.5 inches 1 kg / 41.5 lbs 8.kg / 35.7 lbs 6.2 1032.8 x 670.1 x 92.0 mm 40.7 x 26.4 x 3.7 inches 23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs

AC1 00-240V~50/60Hz 1.5A AC1 00-240V~50/60Hz 2.3A 1 50W 230W
32LG5*** 32LG5000-ZA 32LG5010-ZD 32LG5020-ZB 32LG5030-ZE 32LG5600-ZB
81 x 598.8 x 231.9 mm 3.8 32.1 x 23.6 x 9.2 inches 81 x 540.4 x 95.5 mm 3.8 32.1 x 21.3 x 3.8 inches 1 kg / 31.1 lbs 4.kg / 27 lbs 2.6.8 AC100-240V~ 50/60Hz 1.5A 1.8A (32LG5600) 1 50W 1 80W (32LG5600)
37LG50** 37LG5000-ZA 37LG5010-ZD 37LG5020-ZB 37LG5030-ZE
936.4 x 685.4 x 293.4 mm 36.9 x 27 x 1 inches.0 1.6 936.4 x 61 x 88.0 mm 2.8 36.9 x 24.2 x 3.5 inches 1 kg / 40.4 lbs 8.kg / 34.4 lbs 5.6 AC100-240V~ 50/60Hz 1.8A 1 80W
42LG50** 42LG5000-ZA 42LG5010-ZD 42LG5020-ZB 42LG5030-ZE
1032.0 x 894.8 x 293.8 mm 40.7 x 35.3 x 1 inches 1.6 1032.0 x 662.3 x 89.0 mm 40.7 x 26.1 x 3.5 inches 26.2 kg / 57 lbs.8 23.5 kg / 51.8 lbs AC100-240V~ 50/60Hz 2.3A 230W
32LG5*** MODELS 32LG5700-ZF
47LG50** 47LG5000-ZA 47LG5010-ZD 47LG5020-ZB 47LG5030-ZE
1 56.2 x 81 x 342.9 mm 1 3.1 45.6 x 32.0 x 1 inches 3.1 56.2 x 739.2 x 103.0 mm 45.6 x 29.1 x 4.1 inches 29.2 kg / 64.4 lbs 24.6 kg / 54.3 lbs AC100-240V~ 50/60Hz 3.0A 300W
52LG50** 52LG5000-ZA 52LG5010-ZD 52LG5020-ZB 52LG5030-ZE
1 291.7 x 892.1 x 342.9 mm 7 50.9 x 35.2 x 1 inches 3.291.7 x 81.0 x 1 5.3 mm 50.9 x 32.2 x 4.6 inches 39.5 kg / 87 lbs.1 34.9 kg / 77 lbs.0 AC100-240V~ 50/60Hz 3.3A 330W

with stand without stand

81 x 599.3 x 294.0 mm 3.8 1.6 32.1 x 23.6 x 1 inches 81 x 540.4 x 95.5 mm 3.8 32.1 x 21.3 x 3.8 inches 1 kg / 31.1 lbs 4.kg / 27 lbs 2.6.8 AC100-240V~ 50/60Hz 1.8A 1 80W
Weight Power requirement Power Consumption Television System Programme Coverage
External Antenna Impedance Operating Temperature Environment condition Operating Humidity Storage Temperature Storage Humidity
PROGRAMMING THE REMOTE CONTROL
(Only 19/22/26/32/37/42LG30**, 32/37/42LG20**,32/42LG32**, 32/37/42/47/52LG5***)
The remote control is a multi brand or universal remote. It can be programmed. to operate most remote controlled devices from other manufacturers. Note that the remote control may not control all models from other brands.
Programming a code into a remote mode

[d][ ][Set ID][ ][OK/NG][Data][x]

09. Tint (Command: k j)

G To adjust the screen tint.
13. Balance (Command: k t)

G To adjust balance.

You can also adjust tint in the PICTURE menu.
[k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 ~ Green : 64 14. * Refer to Real data mapping 1. See page 1 Ack [j][ ][Set ID][ ][OK/NG][Data][x]
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 14. * Refer to Real data mapping 1. See page 1 Ack [t][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
G To adjust the screen sharpness.
14. Colour Temperature (Command: k u)
G To adjust colour temperature. You can also adjust
You can also adjust sharpness in the PICTURE menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 ~ Max : 64 14. * Refer to Real data mapping 1. See page 1 Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Colour Temperature in the PICTURE menu. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 00: Medium Ack 01: Cool 02: Warm
[u][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l) G To select OSD (On Screen Display) on/off when controlling remotely.
15. Abnormal State (Command: k z)
G To recognize an abnormal state.
[k][z][ ][Set ID][ ][FF][ ][Cr] Data FF : Read Ack
[k][l][ ][Set ID][ ][Data][Cr] Data 00 : OSD off Ack 01 : OSD on
[z][ ][Set ID][ ][OK/NG][Data][x] Data 00: Normal (Power on and signal exist) 01: No signal (Power on) 02: Turn the monitor off by remote control 03: Turn the monitor off by sleep time function 04: Turn the monitor off by RS-232C function 05: 5V down 06: AC down 07: Turn the monitor off by Fan Alarm function 08: Turn the monitor off by Off time function 09: Turn the monitor off by Auto sleep function a: Turn the monitor off by AV Board detect * This function is read only.
[l][ ][Set ID][ ][OK/NG][Data][x]
1 2. Remote control lock mode ( C o m m a n d : k m )
G To lock the front panel controls on the monitor and
remote control. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 00 : Lock off Ack 01 : Lock on
[m][ ][Set ID][ ][OK/NG][Data][x] * If you are not using the remote control, use this mode. When main power is on/off, external control lock is released.
16. ISM Method (Plasma TV only) (Command: j p )
G To control the ISM method. You can also adjust ISM
19. Equalize (Command : j v)

G To adjust equalize.

Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data 01: Inversion 02: Orbiter 04: White wash 08: Normal
[j][v][ ][Set ID][ ][Data][Cr] MSB Data : 0 LSB 0
[p][ ][Set ID][ ][OK/NG][Data][x]

LCD TV OWNERS MANUAL

LCD TV MODELS L S 4 D* L G 3 0* * L S 4 D* L G 3 2* * L G 2 0* * L G 3 0* * L G 2 0* * L G 3 0* * L G 2 0* * L G 3 2* * L G 3 0* * L G 5* * * L G 3 0* * L G 5 0* * L G 3 0* * L G 5 0* * L G 5 0* * L G 5 0* * Please read this manual carefully before operating your TV. Retain it for future reference. Record model number and serial number of the TV. Refer to the label on the back cover and quote this information. To your dealer when requiring service.
5507: 19LS4D-ZD 5721: 26LG3050-ZA 5631: 42LG2000-ZA 5090: 22LG3000-ZA 5089: 32LG3000-ZA 5086: 42LG3000-ZA 5084: 37LG5000-ZA 5082: 47LG5000-ZA 5385: 52LG5010-ZD 5387: 42LG5010-ZD 5389: 32LG5010-ZD 5391: 47LG5020-ZB 5393: 37LG5020-ZB 5395: 52LG5030-ZE 5397: 42LG5030-ZE 5399: 32LG5030-ZE 5820: 19LG3050-ZA 5879: 19LG3060-ZB 5878: 32LG5600-ZB 651 42LG3200-ZA 1:
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
I D N u m b e r ( s ) : 5499: 22LS4D-ZD 5629: 32LG2000-ZA 5630: 37LG2000-ZA 5088: 19LG3000-ZA 5080: 26LG3000-ZA 5087: 37LG3000-ZA 5085: 32LG5000-ZA 5083: 42LG5000-ZA 5081: 52LG5000-ZA 5386: 47LG5010-ZD 5388: 37LG5010-ZD 5390: 52LG5020-ZB 5392: 42LG5020-ZB 5394: 32LG5020-ZB 5396: 47LG5030-ZE 5398: 37LG5030-ZE 5671: 32LG5700-ZF 5818: 22LG3050-ZA 5880: 22LG3060-ZB 6507: 32LG3200-ZA
Extended Owners Manual that contains advanced features of these LG TV-sets is located on CD-ROM in electronic version. To read it You need to open chosen files by using Personal Computer (PC) equipped with CD-ROM drive.
P/NO: MFL34441652 (0901-REV01) Printed in Korea

CONNECTING YOUR UNIT

Image shown may differ from your TV.

DVD/STB

COMPONENT IN

VIDEO AUDIO

VCR Connection

Power Cord

USB IN SERVICE ONLY
AUDIO IN OPTICAL DIGITAL (RGB/DVI) AUDIO OUT

HDMI/DVI IN 2

RGB IN (PC)
1(DVI) RS-232C IN (CONTROL & SERVICE)
* To connect an additional equipment, see the E x t e r n a l e q u i p m e n t S e t u p section in CD Manual.

ANTENNA IN

Antenna Connection

ENGLISH

HDMI/DVI IN AUDIO IN (RGB/DVI) ANTENNA IN PCMCIA CARD SLOT EJECT
RS-232C IN (CONTROL & SERVICE)

RGB (PC) IN

COMPONENT IN VIDEO AUDIO

SERVICE ONLY

SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product. In this manual, the illustration may be somewhat different from your product because it is just example to help the instruction.
WARNING If you ignore the warning message, you may be seriously injured or there is a possibility of accident or death. CAUTION If you ignore the caution message, you may be slightly injured or the product may be damaged.
Precaution in Installing the Product

WARNING

Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.

CAUTION

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Precautions in Moving the Product
Do not use the product in damp place such as a bathroom or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Make sure to turn off the product. Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
Do not shock the product when moving it.
Install the product on a flat and stable place that has no risk of dropping the product.
- If the product is dropped, you may be injured or the product may be broken.
Make the panel face forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center for repair.
Precautions in Using the Product
Do not disassemble, repair or modify the product at your own discretion.
- Fire or electric shock accident can occur. - Contact the service center for check, calibration or repair.
Keep the product away from direct sunlight.
- The product can be damaged.
Do not place the product in a built-in installation such as bookcase or rack.

- Ventilation required.

Electrical Power Related Precautions
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not keep a still image on the screen for an extended period (e.g. by pausing a video) as the fixed image may remian visible on the screen. This is known as image burn. Image burn is not covered under the manufacturers warranty.

Do not touch the power plug with wet hands. Additionally, it the cord pin is wet or covered with dust, dry the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
During a thunder or lightning storm, unplug the power cable or signal cable.
- You may be electrocuted or a fire can break out.

PREPARATION

FRONT PANEL CONTROLS
Image shown may differ from your TV. If your TV has a protection film attached, remove the film and then wipe the TV with a polishing cloth.
LCD TV Models : 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42/47/52LG5***

PROGRAMME

VOLUME
Intelligent Sensor Adjusts picture according to the surrounding conditions. (32/37/42/47/52LG5*** only) POWER Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates blue when the TV is switched on. Note: You can adjust Power Indicator
LCD TV Models : 19/22LG30**
INPUT MENU OK VOLUME PROGRAMME

in the OPTION menu.

INPUT MENU OK
LCD TV Models : 19/22LS4D*
POWER INPUT MENU OK VOLUME PROGRAMME
Remote Control Sensor Power/Standby Indicator illuminates red in standby mode. illuminates green when the TV is switched on.

BACK PANEL INFORMATION

PCMCIA CARD SLOT

HDMI IN 3

HDMI/DVI IN

AUDIO IN (RGB/DVI)

PCMCIS CARD SLOT

VIDEO L/MONO AUDIO R

1(DVI)
Except for 32/37/42LG20**, 32/42LG32**

S-VIDEO

AV IN 3

AV IN 3 H/P

Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. RGB/DVI Audio Input Connect the audio from a PC or DTV.
Component Input Connect a component video/audio device to these jacks. Antenna Input Connect RF antenna to this jack. PCMCIA (Personal Computer Memory Card International Association) Card Slot (This feature is not available in all countries.) Audio/Video Input (Except for 19/22LS4D*) Connect audio/video output from an external device to these jacks. S-VIDEO (Except for 19/22LS4D*, 32/37/42LG20**, 32/42LG32**) Connect S-Video out from an S-VIDEO device. Headphone Socket (Except for 19/22LS4D*, 32/37/42LG20**, 32/42LG32**) Connect the headphone plug to this socket. SERVICE ONLY PORT
DIGITAL AUDIO OUT OPTICAL (Except for 19/22LS4D*) Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. Euro Scart Socket (AV1/AV2) Connect scart socket input or output from an external device to these jacks. HDMI Input Connect a HDMI signal to HDMI IN. Or DVI (VIDEO) signal to HDMI/DVI port with DVI to HDMI cable. RGB IN (PC) Connect the output from a PC. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC.

STAND INSTALLATION

(LCD TV Models: 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)
When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the product can tilt forward after the product installation.) If you tighten the bolt with excessive force, the bolt can deviate from abrasion of the tightening part of the bolt. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the TV as shown.
Assemble the parts of the S t a n d B o d y with the C o v e r B a s e of the TV.
Fix the 4 bolts securely using the holes in the back of the TV.

Stand Body

Cover Base

(Only 19/22LG30**)

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the parts of the S T A N D B O D Y with C O V E R B A S E of the TV. Insert the S T A N D B O D Y into a C O V E R B A S E until clicking sound. Assemble the TV as shown.

DETACHING STAND

(Only 19/22LS4D*)
Image shown may differ from your TV. Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Place the tv with its front facing downward on a cushion or soft cloth.
Hold the H i n g e B o d y and bend it upward.

Hinge Body

Pull the C o v e r B a s e backward during pressing a button on the S t a n d B o d y.
Insert the S t a n d B o d y into the TV until clicking sound.
Hold the C o v e r B a s e and pull with shake it backward to separate from the S t a n d B o d y.
Hold the S t a n d B o d y and bend it upward.
Pull stand body to separate from the TV during pressing 2 latches.
BACK COVER FOR WIRE ARRANGEMENT
LCD TV Models: 32/37/42LG20**, 26/32/37/ 42LG30**, 32/42LG32**, 32/37/42/47/52LG5***
LCD TV Models : 19/22LS4D*, 19/22LG30**
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section of the manual. Open the C A B L E M A N A G E M E N T C L I P as shown and manage the cables.
Connect the cables as necessary. To connect additional equipment, see the External Equipment Setup section.

CABLE MANAGEMENT CLIP

Install the CABLE MANAGEMENT CLIP as shown.
Fit the C A B L E M A N A G E M E N T C L I P as shown.
How to remove the cable management clip

First, press the cable management. Hold the C A B L E M A N A G E M E N T C L I P with both hands and pull it upward. Hold the CABLE MANAGEMENT CLIP with both hands and pull it backward.

! NOTE

G Do not use the CABLE MANAGEMENT CLIP to lift the TV. - If the TV is dropped, you may be injured or the TV may be damaged.
PLEASE SET IT UP CAREFULLY SO THE PRODUCT DOES NOT FALL OVER.
You should purchase necessary components to fix the TV to the wall on the market. Position the TV close to the wall to avoid the possibility of it falling when pushed. The instructions shown below are a safer way to set up the TV, which is to fix it to the wall, avoiding the possibility of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also prevent the TV from damage. Ensure that children do not climb or hang from the TV.
Use the eye-bolts or TV brackets/bolts to fix the TV to the wall as shown in the picture. (If your TV has bolts in the eyebolts, loosen these bolts.) * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the wall.
Use a sturdy rope to tie the TV. It is safer to tie the rope so it becomes horizontal between the wall and the TV.
When moving the TV undo the cords first. Use a platform or cabinet strong and large enough to support the size and weight of the TV. To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.
The TV can be installed in various ways such as on a wall, or on a desktop etc. The TV is designed to be mounted horizontally.

EARTHING

Ensure that you connect the earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to earth the TV by connecting it to telephone wires, lightening rods or gas pipes.

Power Supply

Circuit breaker
DESKTOP PEDESTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV.

4 inches

Attaching the TV to a desk (Only 32/37/42LG20**, 26/32/37/42LG30**, 32/42LG32**, 32/37/42LG5***)

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. Use only an attached screw. Stand
1-Screw (provided as parts of the product)

! WARNING

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury.
WALL MOUNT: HORIZONTAL INSTALLATION
For adequate ventilation allow a clearance of 4 (10cm) all around the TV. We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.
4 inches 4 inches 4 inches 4 inches
Not using the desk-type stand (Except for 19/22LS4D*)
When installing the wall-mounted unit, use the protection cover for desk-type stand installation. Insert the P R O T E C T I O N C O V E R into the TV until clicking sound.
To prevent damage do not connect to the mains outlet until all connections are made between the devices.

ANTENNA CONNECTION

For optimum picture quality, adjust antenna direction. An antenna cable and converter are not supplied.

Wall Antenna Socket

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

HDMI IN RGB IN

VARIABLE AUDIO OUT

RF Coaxial Wire (75 ohm)

Outdoor Antenna (VHF, UHF)
Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Antenna

Signal Amplifier
In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the antenna as shown above. If signal needs to be split for two TVs,use an antenna signal splitter for connection.
WATCHING TV /PROGRAMME CONTROL
REMOTE CONTROL KEY FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.

TV D/A POWER INPUT

TV/RADIO TEXT I/II MUTE

7 LIST

9 Q.VIEW

AV MODE

INFO i

VOL EXIT RETURN

INPUT External input mode rotate in regular sequence. Switches the TV on from standby. GUIDE Shows programme schedule. THUMBSTICK(Up/Down/LeftRight) Allows you to navigate the on-screen menus and adjust the system settings to your preference. OK Accepts your selection or displays the current mode. Programme UP/DOWN Selects a programme. Q.VIEW Returns to the previously viewed programme.

MODE Selects the remote operating modes. Q. MENU Select the desired quick menu source. MENU Selects a menu. Clears all on-screen displays and returns to TV viewing from any menu. VOLUME UP /DOWN Adjusts the volume. POWER Switches the TV on from standby or off to standby.

Installing Batteries

Open the battery compartment cover on the back and install the batteries matching correct polarity (+with +,-with -). Install two 1.5V AAA batteries. Do not mix old or used batteries with new ones. Close cover.

TURNING ON THE TV

- When your TV is turned on, you will be able to use its features.
Firstly, connect the power cord correctly. At this stage, the TV switches to standby mode. (or PR D E) button on the TV or In standby mode to turn TV on, press the r / I, INPUT or P press the POWER, INPUT, D/A, P (or PR + -) or NUMBER button on the remote control and the TV will switch on.

Initializing setup

If the OSD (On Screen Display) is displayed on the screen after turning on the TV, you can adjust the Language, Select Mode, Country, Time Zone, Auto programme tuning.
Note: a. It will automatically disappear after approx. 40 seconds unless a button is pressed. b. Press the BACK or RETURN button to change the current OSD to the previous OSD. c. For those countries without confirmed DTV broadcasting standards, some DTV features might not work, depending on the DTV broadcasting environment. d. "Home mode is the optimal setting for home environments, and is the TV's default mode. e. "In Store" mode is the optimal setting for store environments. If a user modifies image quality data, In Store mode initializes the product to the image quality set by us after a certain period of time. f. The mode (Home, In Store) can be changed by executing Factory Reset in the OPTION menu.
ON-SCREEN MENU LANGUAGE / COUNTRY SELECTION
The installation guide menu appears on the TV screen when it is switched on for the first time.
Select your desired language.

Select your country.

* If you want to change Language/ Country selection
Select O P T I O N. Select M e n u L a n g u a g e or C o u n t r y.

Select your desired language or country. Save it.

G G G G G

If you do not finish the set-up Installation Guide by pressing RETURN or if you time out on the OSD (On Screen Display) the installation menu will continuously appear until the set up is completed whenever the TV is switched on If you select the wrong local country, teletext may not appear correctly on the screen and some problems may occur during teletext operation. The CI (Common Interface) function may not be applied based on country broadcasting circumstances. DTV mode control buttons may not function based on country broadcasting circumstances. In country that Digital broadcasting regulation isnt fixed, some DTV function may not work depending on digital broadcasting circumstances. The Country Setting UK should only be activated UK.
ON SCREEN MENUS SELECTION AND ADJUSTMENT
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. SETUP

Move OK

Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information

PICTURE

Aspect Ratio Picture Mode : 16:9 : Vivid Backlight Contrast Brightness Sharpness Colour Tint
Auto Volume Balance Sound Mode : Off 0 : Standard 120Hz 200Hz 500Hz 1.2KHz 3KHz

OPTION

+ + + + +
Clock Off Time On Time Sleep Timer Auto Sleep Time Zone
Menu Language Audio Language Subtitle Language Hard of Hearing( Country Input Label SIMPLINK Key Lock
: Off : Off : Off : Off : Canary GMT
: English : English : English ) Off :UK : Off : Off
Lock System : Off Set Password Block Programme Parental Guidance : Off

1MENU 2

Display each menu.

Select a menu item.

Move to the pop up menu. Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

AUTO PROGRAMME TUNING

Use this to automatically find and store all available programmes. When you start auto programming in digital mode, all previously stored service information will be deleted.

Auto tuning Auto tuning Manual tuning Programme Edit Booster : On Software Update : Off Diagnostics CI Information
All service-information will be updated. Continue? Yes

SECAM L Search

Select SETUP.
Use NUMBER buttons to input a 4-digit
password in Lock System On.
If you wish to keep on auto tuning select YES

Select Auto Tuning.

using the button. Then, press the OK button. Otherwise select NO.

Select Yes.

Run Auto tuning.
Press the MENU button to return to normal TV viewing. Press the RETURN button to move to the previous menu screen.

APPENDIX

MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can prolong the life of your new TV. Caution: Be sure to switch the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

A good way to keep the dust off your screen for a while is to wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it is almost dry, and then use it to wipe the screen. Ensure there is no excess water on the screen. Allow any water or dampness to evaporate before switching on.

Cleaning the Cabinet

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Do not to use a wet cloth.

Extended Absence

If you expect to leave your TV dormant for prolonged periods (such as a holiday), unplug the power cord to protect against possible damage from lightning or power surges.
TO VIEW THE USER'S GUIDE ON THE CD-ROM
To view the User's guide on the CD-ROM, Adobe Acrobat Reader must be installed on your PC. The "ACRORD" folder on the CD-ROM contains the installation program for Acrobat Reader. If you want to install Acrobat Reader, Open "My Computer" Open the folder "LG" Open the folder "ACRORD" double-click your language. To view the User's guide The User's guide files are included in the supplied CD-ROM. Load the supplied CD-ROM into the CD-ROM drive of your PC. After a while, the web page of the CD-ROM will open automatically.(Windows users only) If the web page does not appear automatically, open the User's guide file directly. Open "My computer" Open the folder "LG" Double click the "index.htm" file.

TROUBLESHOOTING

The TV does not operate properly. Check to see if there is any object between the TV and the remote control causing an obstruction. Ensure you are pointing the remote control directly at the TV. A Ensure that the batteries are installed with correct polarity (+ to +, - to -). A Ensure that the correct remote operating mode is set: TV, VCR etc. A Install new batteries.
The remote control does not work
Power is suddenly turned off
Is the sleep timer set? Check the power control settings. Has the Power supply been interrupted. A Is Auto sleep activated on this station?

The video function does not work.

No picture &No sound

Check whether the TV is switched on. Try another channel. The problem may be with the broadcast. A Is the power cord inserted correctly into the mains? A Check your antenna direction and/or location. A Test the mains outlet by plugging another TV into the same outlet.
Picture appears slowly after switching on
This is normal, the image is muted during the TV startup process. Please contact your service centre, if the picture has not appeared after five minutes.
No or poor colour or poor picture
Adjust Colour in menu option. Allow a sufficient distance between the TV and the VCR. A Try another channel. The problem may be with the broadcast. A Are the video cables installed properly? A Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking Poor reception on some channels Lines or streaks in pictures No picture when connecting HDMI
Check for local interference such as an electrical appliance or power tool.
Station or cable channel experiencing problems, tune to another station. Station signal is weak, reposition the antenna to receive weaker stations. A Check for sources of possible interference.
Check antenna (Change the position of the antenna). Check HDMI cable over version 1.3. If the HDMI cables dont support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
The audio function does not work.
Picture OK & No sound
Press the VOLUME button. Sound muted? Press MUTE button. Try another channel. The problem may be with the broadcast. Are the audio cables installed properly? Adjust Balance in menu option. A change in ambient humidity or temperature may result in an unusual noise when the TV is switched on or off and does not indicate a fault with the TV. Check HDMI cable over version 1.3. Check USB cable over version 2.0.

No output from one of the speakers Unusual sound from inside the TV No sound when connecting HDMI or USB
*This feature is not available for all models.
There is a problem with PICTURE settings. When the user changes the picture settings, the TV automatically converts back to the initial settings after a certain period of time.
It means that the TV is currently set to I n S t o r e mode. To switch to H o m e mode you should do the followings: From the TV Menu, choose O P T I O N -> F a c t o r y R e s e t -> Y e s (wait for a W few seconds for the TV to download again) -> OSD "W E L C O M E" appears -> Press O K button -> Choose L a n g u a g e -> Choose H o m e -> Select your C o u n t r y and T i m e Z o n e -> Press O K button. Program search will begin automatically (You can stop the search by pressing the O K button). Now, you have completed switching to the H o m e mode.

WEIGHT

19LS4D* MODELS 19LS4D-ZD 22LS4D-ZD 22LS4D* 19LG30** 19LG3000-ZA 19LG3050-ZA 19LG3060-ZB
5.02 kg / 1 lbs 1.1 4.76 kg / 10.5 lbs

Weight

with stand without stand
5.1 kg / 1 lbs 1.3 4.6 kg / 10.2 lbs
6.1 kg / 1 lbs 3.5 5.7 kg / 1 lbs 2.6
22LG30** MODELS 22LG3000-ZA 22LG3050-ZA 22LG3060-ZB
5.6 kg / 1 lbs 2.4 5.34 kg / 1 lbs 1.8
26LG30** 26LG3000-ZA 26LG3050-ZA
10.1 kg / 22.3 lbs 8.6 kg / 19.0 lbs
32LG30** 32LG3000-ZA 32LG3030-ZA
1 kg / 29.6 lbs 3.kg / 26.3 lbs 1.9
37LG30** MODELS 37LG3000-ZA 37LG3030-ZA
1 kg / 41.5 lbs 8.kg / 35.7 lbs 6.2
42LG30** 42LG3000-ZA 42LG3030-ZA
23.6 kg / 52.1 lbs 21.0 kg / 46.3 lbs

32LG20** 32LG2000-ZA

37LG20** 37LG2000-ZA
42LG20** MODELS 42LG2000-ZA

32LG32** 32LG3200-ZA

42LG32** 42LG3200-ZA
32LG5*** 32LG5000-ZA 32LG5010-ZD 32LG5020-ZB 32LG5030-ZE 32LG5600-ZB 32LG5700-ZF
1 kg / 31.1 lbs 4.kg / 27 lbs 2.6.8
37LG50** MODELS 37LG5000-ZA 37LG5010-ZD 37LG5020-ZB 37LG5030-ZE
1 kg / 40.4 lbs 8.kg / 34.4 lbs 5.6
42LG50** 42LG5000-ZA 42LG5010-ZD 42LG5020-ZB 42LG5030-ZE
26.2 kg / 57 lbs.8 23.5 kg / 51.8 lbs
47LG50** 47LG5000-ZA 47LG5010-ZD 47LG5020-ZB 47LG5030-ZE
29.2 kg / 64.4 lbs 24.6 kg / 54.3 lbs
52LG50** 52LG5000-ZA 52LG5010-ZD 52LG5020-ZB 52LG5030-ZE
39.5 kg / 87 lbs.1 34.9 kg / 77 lbs.0
The specifications shown above may be changed without prior notice for quality improvement.

(UK only)