To Instrument's exposed METALLIC PARTS

0.15uF

Good Earth Ground such as WATER PIPE, CONDUIT etc.

1.5 Kohm/10W

SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.

Application Range

This spec is applied to the 50 PLASMA TV used PP7BA Chassis. Chassis PP7BA Model Name 50PT81-ZB Market EU Brand LG Remark

Specification

Each part is tested as below without special appointment. 1) Temperature : 255C (779F), CST : 405 2) Relative Humidity: 6510% 3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz) * Standard Voltage of each product is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with SBOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.

Test Method

1) Performance : LGE TV test method followed. 2) Demanded other specification Safety : CE, IEC specification EMC : CE, IEC Model 50PT81-ZB Market EU Appliance Safety : IEC/EN60065, EMI : EN55013, EMS : EN55020 Remark TEST

Module Specification1

No Panel PDP Module Outline Dimension 50X4 50X4P Pixel Pitch 50X4 50X4P Pixel Format 50X4 50X4P Pixel Type Item Specification 50 WXGA PDP 1190 x 703 x x 700 x 52 0.81 x 0.81 (1 pixel = 3 RGB cells) 0.81 x 0.81 (1 pixel = 3 RGB cells) 1366 x 768 Pixels RGB strip arrangement 1365 x 768 Pixels RGB strip arrangement RGB Closed type mm 50X4P (H)mm x (V)mm x (D)mm Remark

Module Specification2

No 3 Market Broadcasting system Available Channel Item EU PAL BG/I/DK, NTSC, SECAM BAND VHF/UHF CATV Receiving system Operating Environment Upper Heterodyne 1) Temp : 0 ~ 40 deg 2) Humidity : 10 ~ 90 %RH 6 Storage Environment 1) Temp : -20 ~ 50 deg 2) Humidity : 10 ~ 90 %RH 7 Power Consumption Power on (Green) < 500 1/8W non-clipped max. audio signal. Input voltage 198Vac/60HZ. Full White video input. 8 Stand by Cool Warm 9 Frequency range H : 31 ~ 61Khz V : 56 ~ 75Hz SCART Jack(2EA) Video Input (1EA) S-Video Input (1EA) Component Input (1EA) RGB Input (1EA) HDMI Input (2EA) RS-232C(1EA) Audio Input (3 EA) PAL, SECAM PAL, SECAM, NTSC PAL, SECAM, NTSC Y/Cb/Cr, Y/ Pb/Pr RGB-PC HDMI-PC, HDMI-DTV Remote control, S/W Upgrade PC Audio, Component (1EA), SIDE AV(1EA) Audio variable out(1EA) USB Input(1EA) DivX, MP3, JPEG SIDE(1EA) L/R Input FULL SCART, HALF SCART SIDE AV SIDE S-VIDEO < 1W < 55W PC Input PAL C1~C69 S1~S47 Specification Remark

ADJUSTMENT INSTRUCTION

1. Application Object
These instructions are applied to all of the 50 PLASMA TV, PP7BA Chassis.
4. HDD assembly adjustment method

4-1. HDD Format

1) Assemble MAIN , DVR Board. 2) HDD Format in progress words will create automatically. 3) Please, wait for 30~40 seconds. (1) HDD Format in progress.

2. Note

(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 255C of temperature and 6510% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 100-220V~, 50/60Hz. (5) Before adjustment, execute Heat Run for 30 minutes.

3. Adjustment items

3.1. PCB assembly adjustment items
(1) Channel memory 1) Download the channel data from BOM to EEPROM by using LGIDS. (2) Option adjustment following BOM 1) Push the ADJ key in the Adjust Remocon. 2) Input the Option Number that was specified in the BOM, into the Shipping area. 3) Select Tool Option1/ Tool Option2/ Area Option by using D/E(CH+/-) key, and press the number key(0~9) consecutively. ex) If the value of Tool Option1 is 7, input the data using number key 7(Fig.1). (3) Color carrier Adjustment. (2) HDD Format completed.

PPBA/BB 50X4P WXGA

4-2. Sub Program Download for DVR by using USB memory stick
(1) Connect USB memory stick to SET. (2) Set power off -> On - DVR s/w will be installed automatically.

(Fig.1)

3.2. SET assembly adjustment items
(1) Auto AV Color Balance. (2) Adjustment of White Balance. (3) Auto Component Color Balance adjustment. - standard equipment : MSPG925FA. (4) Auto RGB Color Balance adjustment. - standard equipment : MSPG925FA ( At DVR model Case, Please check DVR function like following list ) (5) Checking DVR Function and HDD * Check DVR Function as follow on 4-2 and find HDD failure under malfunction.
Each PCB assembly must be checked by check JIG set. (Because power PCB Assembly damages to PDP Module, especially be careful)
5. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage adjustments)
5-1. Test Equipment : D.M.M. 1EA 5-2.Connection Diagram for Measuring

: refer to Fig.2

* Use the proper signal cabel for EDID Download - Analog EDID : Pin3 exists - Digital EDID : Pin3 exists * Never connect HDMI & DVU-D & DVI-A Cable at the same time. * Use the proper cables below for EDID Writing * HDMI 1 and HDMI2 is different each other. So you have to Download different EDIT File.

7. EDID

For Analog EDID D-sub to DVI-I For Digital EDID DVI-D to DVI-D

5-3. Adjustment Method

(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN. 2) Connect + terminal of D.M.M to Va pin of P812, connect - terminal to GND pin of P812. 3) After turning VR501, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V) For HDMI EDID

(2) Vs Adjustment

1) Connect + terminal of D.M.M to Vs pin of P812, connect terminal to GND pin of P812. 2) After turning VR401, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; 0.5V)
DVI-D to HDMI or HDMI to HDMI

7-1. EDID Data

No 3 Item Manufaturer Version Revision Condition GSM Digital : 1 Digital : 3 Hex Data 1E6D 01 03
(Fig.2) Connection diagram of power adjustment for measuring

6. ADC Calibration

ADC RF/AV/S-VIDEO PAL INPUT AV1 - TB Model:217(720P) Model : 60 (1024*768 60Hz) *100% Color Bar *100% Color Bar Pattern : 65 MSPG925FA SELECT AV3 - ZF Pattern : 65 Model : 202 (PAL-BGDHI) Pattern : 65 *100% Color Bar * Press the FRONT-AV Key on R/C for converting input mode. (Change RS-232 Host : pc, BaudRate : 115200bps) - System control RS-232 Host should be PC for adjustment. Component RGB-PC

7-2. Analog(256Byte)

(1) BLOCK1(128Byte)
8. Adjustment of RF/AV/S-VIDEO

8-1. Requirement

(1) This AV color balance adjustment should be performed before white Balance Adjustment. (2) After AV color balance adjustment, Change the mode from AV to RF.

8-2. Required Equipment

(1) Remote controller for adjustment. (2) 802F Pattern Generator, Master(MSPG-925FA), etc. (3) MSPG-925FA Pattern Generator. (Which has Video Signal : 100% Color Bar Pattern shown in Fig.3) -> Model : 202 / Pattern : 65

7-3. HDMI(256Byte)

(Fig. 3)

(2) BLOCK2(128Byte)

8-3. Method of Auto RF/AV/S-VIDEO Color Balance
(1) Press the FRONT-AV KEY on R/C for converting input mode. (2) Input the Video Signal: 100% Color Bar signal into AV. (3) Set the PSM to Dynamic mode in the Picture menu. (4) Press INSTART key on R/C for adjustment. (5) Press the G(Vol.+) key to operate the set, then it becomes automatically. (6) Auto-RGB OK means the adjustment is completed.

=> Detail EDID Options are below([1], [2], [3],[4], [5]) 1. [1]-Product ID Model Name 42PB4RT 50PB4RT 42PT81 50PT81 2. [2]-Serial No : Controlled on production line 3. [3]-Month, Year : Controlled on production line ex) Week : '03' => '03' Year : '2005' => '0F' 4. [4]-Model Name(Hex): Model Name LG TV 00 FC 00 4C 0A 20 5. [5]-Checksum : Changeable by total EDID data

Product ID

Product ID Hex EDID table
9. Adjustment of Component

9-1. Required Equipment

(1) Remote controller for adjustment. (2) 802F Pattern Generator, Master(MSPG-925FA), etc. (3) MSPG-925FA Pattern Generator. (Which has 720P@60Hz YPbPr Signal : 100% Color Bar Pattern shown in Fig.4) -> Model : 217 / Pattern : 65 (4) It is very import to use correct adjustment pattern like Fig.4. 1) Within the pattern, color sequence should be aligned : White-Yellow-Cyan-Green-Gray-Red-BLUE-BLACK ( If color sequence is reversed (Black ->.-> White), reverse the pattern with REV key, when using Master pattern generator like MSPG-925) 2) If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.

10. Adjustment of RGB

10-1. Required Equipment
(1) Remote controller for adjustment. (2) 802F Pattern Generator, Master(MSPG-925FA), etc. (3) MSPG-925FA Pattern Generator. (Which has XGA [1024*768] 60Hz PC Format output signal : 100% Color Bar Pattern shown in Fig.5) (4) It is very import to use correct adjustment pattern like Fig.5. 1) Within the pattern, color sequence should be aligned : White-Yellow-Cyan-Green-Gray-Red-BLUE-BLACK ( If color sequence is reversed (Black ->.-> White), reverse the pattern with REV key, when using Master pattern generator like MSPG-925) 2) If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.

(Fig. 4) (Fig. 4)

9-2. Method of Auto Component Color Balance
(1) Input the Component 720p 100% Color Bar(MSPG-925FA model:217, pattern:65) signal into Component. (2) Set the PSM to Dynamic mode in the Picture menu. (3) Press the INSTART key on R/C for adjustment. (4) Press the G(Vol.+) key to operate the set , then it becomes automatically. (5) Auto-RGB OK means the adjustment is completed.

10-2. Method of Auto RBG Color Balance

11. White Balance

- Before White-balance, the AV ADC should be done. * Notice - Do the white balance adjustment under the 10LUX - Before white balance, press the In-start key 2times and do the reset like Fig.6 - Use the Torino inner pattern(216 gray pattern) - To enter White-balance mode,press the IN-START key 2times. - System control RS-232 Host should be PC for adjustment.
Target Value of Brightness, Color Coordinates, Color Temperature
High Light High Light 60 20cd/m2(42XGA) Cool Normal Cool Warm X: 0.2760.002, Y: 0.2830.002 X: 0.3130.002, Y: 0.3290.002 11,000500K 6,500K500K
Desired result (216 Gray)
Brightness Color -Coordinate Color Temperature
Desired result for high altitude(216 Gray)
Brightness Color -Coordinate Color Temperature High Light High Light 50 20cd/m2(80% of non-high altitude) Cool Normal Cool Warm X: 0.2760.002, Y: 0.2830.002 X: 0.3130.002, Y: 0.3290.002 11,000500K 6,500K500K
11-3.Manual white Balance (INNER Pattern)
(For White Balance, Adjust twice, Cool and Warm)

80 7D 80 8C

(Fig.6)
(1) Execute CA-100, CA-210(10CH) or CA-100 Zero Calibration. (2) Use torino inner pattern as below Fig.7, Supply 216Level (85 IRE) full screen pattern (3) Enter the White Balance adjustment mode by pressing the INSTART key twice(White Balance) on R/C. (4) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and Offset) using D/E (CH+/-) key on R/C. (5) Adjust with R / G / B Gain using F/G (VOL+/-) key on R/C. (6) Adjust it until color coordination becomes as below. - After All adjustment is completed, Please push Instop Key.

11-1. Test Equipment

(1) Color Analyzer (CA-100),CA-210. * Note : When using the Color Analyzer with PDP, recommend the CA-100 more than CA-210. If CA-100 can not available, it is also good th use the CA-210 (2) PC(for communication through RS-232C) -> UART Baud rate : 115200. (3) Pattern Generator(MSPG-925FA etc.)

Color Temperature : Cool, Medium, Warm (1) One of R/G.B Gain should be fixed at 80 and adjust two Gain Value with decreasing the Default values from 80 1) When R Gain is Fixed at Default value(80) - Adjust G gain and B gain with decreasing Default values from 80 2) When B Gain is Fixed at Default value(80) - Adjust R gain and G gain with decreasing Default values from 80 3) When G Gain is Fixed at Default value(80) - Adjust R gain and B gain with decreasing Default values from 80 (2) R/G/B Gain and R/G/B Offset Default Value. - Red Gain : 80 - Green Gain : 80 - Blue Gain : 80
11-2. Color Temperature & Color Coordinates Setting
(1) When adjusting the Color Temperature of PDP, Color Analyzer CA-210(Matrix should be corrected through CH10 of CS-1000) should be used. When CA-210 have used, it dont need to fit the CH10. (2) Adjust the Color Temperature based below adjustment color coordinates. (3) Even if CH9 of CA-210 is corrected with Matrix, there may be many character of Module and Filter. (4) Therefore Refer to the below Color Coordinates Target. But, in case of WCG module, use the CH12 of CA-210.
Target Value CA-210(CH10), CA-100 CSM COOL WARM Temp 11,000K 6,500K x y uv +0.000 +0.003 (Fig.7)
0.2760.002 0.2830.002 0.3130.002 0.3290.002
( R/G/B gain and R/G/B offset Default values are different in according to using module)

- 10 -

11-4.Auto white Balance (INNER Pattern)
No Input Select Command1 x Command2 b Set ID 00 00h 01h 10h 11h 20h 21h 40h 41h 60h 90h Min R-Gain_Normal G-Gain_Normal B-Gain_Normal R-Gain_Warm G-Gain_Warm B-Gain_Warm R-Gain_Cool G-Gain_Cool B-Gain_Cool R-Offset_Normal G-Offset_Normal B-Offset_Normal R-Offset_Warm G-Offset_Warm B-Offset_Warm R-Offset_Cool G-Offset_Cool B-Offset_Cool COLOR TEMP. j j j j j j j j j l l l l l l l l l k a b c d e f g h i j k l m n o p q r u 00 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00 Inner Pattern Signal w b ff Max 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 80h 03h(Cool,Normal,Warm,User) W/B Adjustment Start Using Internal Pattern W/B Adjustment Completion Data Mode DTV-Air Cable RF-Air Cable AV1 AV2 COMP1 COMP1 RGB-PC HDMI INIT 80h 80h 80h 80h 80h 80h 80h 80h 80h

- 11 -

Input Select Data
: RF(10), AV1~4(20,21,22,23), SAV(30), COMP(40), DVI(50 or 60), HDMI(90)

Command Set

( SET ID : 0 -> ALL, 1~99 -> each SET )

Adjustment contents

POWER ON/OFF MAIN INPUT

KA(ka) XB(xb)

SET ID

0~99 0~99

0~1 10~90 0: OFF,
RF(10), AV1~4(20,21,22,23), SAV(30), COMP(40), RGB(50 or 60), HDMI(90)

KC(kc)

4:3; 16:9; SPECTACLE; ZOOM; ORIGINAL; 14:9; FULL

SCREEN MUTE AUDIO MUTE VOLUME CONTRAST BRIGHTNESS COLOR TINT SHARPNESS OSD ON/OFF CHILD LOCK PIP MODE PIP ARC PIP POSITION TREBLE BASS BALANCE COLOR TEMP. RED LEVEL GREEN LEVEL BLUE LEVEL PIP INPUT
KD(kd) KE(ke) KF(kf) KG(kg) KH(kh) KI(ki) KJ(kj) KK(kk) KL(kl) KM(km) KN(kn) KO(ko) KQ(kq) KR(kr) KS(ks) KT(kt) KU(ku) KV(kv) KW(kw) K$(k$) XY(xy)
0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~99
0~1 0~1 0~64 0~64 0~64 0~64 0~64 0~64 0~1 0~1 0~3
1: MUTE, 0: MUTE OFF 1: MUTE, 0: MUTE OFF 0: 0, 0: 0 , 0: 0 , 0: 0 , 64 : 100 (Hexadecimal) 64 : 100 (Hexadecimal) 64 : 100 (Hexadecimal) 64 : 100 (Hexadecimal)
0: R50 , 64 : G50 (Hexadecimal) 0: 0 , 64 : 100 (Hexadecimal) 1: ON

0: OFF,

1: LOCK, 0: OFF PIP_OFF, PIP, DW1, DW2 NOT USED NOT USED
0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~99
0~64 0~64 0~64 0~3 0~50 0~50 0~50 10~90

0:0 , 0:0 , 0:L50,

64:100 64:100 64:R50
COOL, NORMAL, WARM, USER 0 : -40, 0 : -40, 0 : -40, 50 : : : 40
RF(10), AV1~4(20,21,22,23), SAV(30), COMP(40), DVI(50 or 60), ,HDMI(90)

CURRENT STATE

KZ(kz)
ACK is 0, there is Signal ACK is 1, there is No Signal ACK is 2, power Off Status

- 12 -

WHITE BALANCE J(A~F) 32 RED GAIN GREEN GAIN BLUE GAIN RED OFFSET GREEN OFFSET BLUE OFFSET AUTO CONFIG. JA JB JC JD JE JF JU 0~99 0~99 0~99 0~99 0~99 0~99 0~99 0~3F 0~3F 0~3F 0~3F 0~3F 0~3F 01 0:0, 3F:3F , FF: Current State 0:0, 3F:3F , FF: Current State 0:0, 3F:3F , FF: Current State 0:0, 3F:3F , FF: Current State 0:0, 3F:3F , FF: Current State 0:0, 3F:3F , FF: Current State The state is not Auto Adjust Condition Send NACK TUNER CONTROL FACTORY IR 35 ADC Calriblation 36 Red,Blue,Green Gain Ja,Jb,Jc 00<E0 Min:00 Max:fe Initial Value : red blue -0x79 -0x6f IR CODE MC 0~99 Over F0 IR CODE 0, BITMASK = 0X01 SELECT PR. SELECT SUB PR. MA MB 0~99 0~99 0~C7 0~C7 0: Pr. 0, 0: Pr. 0, C7: Pr.199 C7: Pr.199
green -0xRed,Blue,Green offset Jd,Je,Jf 00<90 Min:00 Max:fe Initial Value : red blue -0x80 -0x82

green -0x80

- 13 -
12. Detail list of SVC Option data

Option

Maker Inch Tool Tuner Num. Tool Option1 EYE INDEX VFD HDMI Type(A) Rear AV BOOST Full Tool Option2 Soft Touch Reserved Area Option Option1 Option2 Option3 Option4 System Control1 System Control2 System Control2 Power-off History Panel Control Fan Control

Detail List

CMO 50

Remark

- 14 -

13. Shipped condition

(1) 1) Push the IN-START key in a Adjust Remocon. (2) Input the Option Number that was specified in the BOM, into the Shipping area. (3) The work is finished, Push V Key.

1 STATION

Auto Tuning Manual Tuning Promgrame Edit Favourite Prog.

Condition

System/Storage From/Start Storage/System/Band/Channel/Fine/S earch/Name To Set -- -- -Dynamic/Standard/Mild/User1/User2 Cool Auto Cinema : Off Black Level : Disable Spectacle/Full/Original/4:3/ 16:9/14:9/Zoom1/Zoom2 To Set Disable Disable SRS TSXT/ Standard/ Music/ Movie/ Sports/ User Off 0 On Year -- : -Date -- : -Time -- : --

PICTURE

Picture Mode Color Temperature XD Advanced Aspect Ratio Picture Reset Screen XD Demo
Sound Mode Auto Volume Balance TV Speaker

Off Time On Time

Off 00 : 00 Off 00 : 00 Volume 30 Programme 0
Sleep Time Auto Sleep 5 STATION SPECIAL Country Input Label SIMPLINK Key Lock Set ID 6 DVR Time Control Recorded TV Manual Recording Scheduled List Video Quality HDD Format Language
Off Off To Set To Set To Set Off Off Off On To Set To Set To Set High To Set

- 15 -

TROUBLESHOOTING

1. No power

(1) Symptom
1) Minute discharge does not occur at module. 2) Front LED does not activate.

(2) Press check

Start Check
Is the power cord plugged in?

Plug in the power cord

Are the line filter and PSU connected?
Connect the cable. ) Plasma(
Yes Is the correct fuse for the PSU in place? Plasma(F101) Yes

Replace the fuse.

Is the PSU and 13pin cable connected to the VSC board? Yes

Connect the 13pin cable.

After remove all cables connected PSU(except the CN101), authorizes the AC voltage marking manual. If the ST-by 5V does not operate, replace the PSU.

- 16 -

2. Protect mode
1) After lighting once it does not discharge minutely from the module. 2) The relay falls.(there is an audible Click.) 3) The color of the front LED turns from green to red.

- 20 -

9. In the case of an unusual display in SCART 1 mode(main).
Is the video input of the A/V jack normal?(Check R102)
10. In the case of an unusual display in SCART 1_RGB mode(main).
Is the video input of the A/V jack normal?(Check L111, L112, L112) Yes
11. In the case of an unusual display in SCART 2 mode(main).
Is the video input of the A/V jack normal? (Check R115)

- 21 -

12. In the case of an unusual display in SCART 2_YC mode(main).
Is the video input of the A/V jack normal?(Check R115,R149)
13. In the case an unusual display in RF mode(Sub).
Is the video output of the Tuner normal? (Check TU201_Pin14) No Is the Tuner Cable connected? No Yes Re-insert the cable. No Is the input voltage normal?(Check Pin8, Pin6) No Check the power. Yes Is the I2C communication normal? (Check Pin5, Pin4) No Check the Tuner.
Is the video output of the CXA2069Q normal? (Check R312, in case of S-Video Check R312, R314) Yes No Is the input voltage normal?(Check L308) Yes Is the I2C communication normal? (Check R309, R310)

No Change the IC(IC300).

14. In the case PIP doesnt display in other mode(Sub).
- Same as the case of main except block A should be change to B

- 22 -

15. In the case of an unusual display in component 1 mode(main/sub).
Is the video input of the JK102 normal? (Check L126, L127,L128)
16. In the case of an unusual display in component 2 mode(main/sub).
Is the video input of the Jk103 normal? (Check L129, L130, L131) Yes
17. In the case of an unusual display in RGB mode(main/sub).
Is the R, G, B input and H, V sync of the JK500 normal?(Check R509, R511, R512, R513, R515) Yes

- 23 -

18. No Sound
1) LED is green. 2) There is a picture but no sound.
No Is there sound in any mode?

Is the speaker on?

Set speaker on in the menu.
Is there no sound only for HDMI?
No Download the EDID data.
Is the speaker cable normal?

Check the Speaker cable

Is there no sound only AV?
Is the output of IC300(Pin52,53) normal? Yes

Replace the IC300

Yes Check the signal after IC300. refer to circuit diagram.
Is the IC400 operating normal?

No Replace the IC400

Yes No Check the Tuner In/Out. Is the IC401 operating normal? No Replace the IC401
Is there no sound only for RF?
Is the IC402 operating normal?

No Replace the IC402

Replace the VSC B/D

- 38 -

LOC. NO. ZD401 ZD605
PART NO. 0DZRM00248A 0DR050008AA
DESCRIPTION / SPECIFICATION RLZ8.2B 8.2V 7.78TO8.19V 8OHM 500 SD05.TC - 6V 14.5V 24A 350W SOD32

LOC. NO. IC902

PART NO. EAN32205201
DESCRIPTION / SPECIFICATION HY5DU281622FTP-5 128MBIT 8 x 16bi
FILTERs & INDUCTORs LEDs
AL1200 D101 LD1003 LD1104 LD1301 LD1302 0DL200000CA 0DL233309AC 0DL233309AC 0DL233309AC 0DL233309AC SAM5670(DL-2LRG) ROUND 4.8MM Y-GR SAM2333 RED/Y-GREEN 2.7V 2.8V 30m SAM2333 RED/Y-GREEN 2.7V 2.8V 30m SAM2333 RED/Y-GREEN 2.7V 2.8V 30m SAM2333 RED/Y-GREEN 2.7V 2.8V 30m AL1201 AL1202 AL1203 AL1204 AL1205 F1 6210TCE002B 6210TCE002B 6210TCE002B 6210TCE002B 6210TCE002B 6210TCE002B 6210VH0004A 6210VH0004B EAM30764101 6200J00005N 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6200J00005N 6200J00005N 6200J00005N EAM30764101 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N EAM30764101 6210TCE001G 6200J00005N EAM33010401 EAM33010401 EAM33010401 EAM33010401 EAM33010401 EAM30764101 6200J00005N 6200J00005N 6200J00005N 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6210TCE001G 6200J00005N 6200J00005N 6200J00005N 6200J00005N 6200J00005N Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, HB-4M3216-121JT 120OHM 3.2X1.6X1. Filter, 6210VH0004A 100OHM 30MM 13MM 34MM Filter, ZCAT1518-0730-M- K 65OHM 15MM 7MM Filter, MBW3216-501TF 500ohm 3.2X1.6X0.85 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, MBW3216-501TF 500ohm 3.2X1.6X0.85 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, MBW3216-501TF 500ohm 3.2X1.6X0.85 Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, MEM2012P25R0 EMI 25MHZ 100pF 400N Filter, MEM2012P25R0 EMI 25MHZ 100pF 400N Filter, MEM2012P25R0 EMI 25MHZ 100pF 400N Filter, MEM2012P25R0 EMI 25MHZ 100pF 400N Filter, MEM2012P25R0 EMI 25MHZ 100pF 400N Filter, MBW3216-501TF 500ohm 3.2X1.6X0.85 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M3216-501JT 500OHM 3.2X1.6X1. Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1 Filter, HH-1M2012-121JT(H:1mm) 120OHM 2X1

DESCRIPTION / SPECIFICATION Harness,SingleSMH250 SMP250 600mM 2.50MM 4P UL1 Harness,SingleSMH200 SMH200 700mM 2.00MM 6P UL1 Harness,Single12505HS-04 12505HS-04 700mM 1.25M Harness,Single6631V25032C GIL-G-3S-S3C2 GIL-M-3 Harness,SingleGP390-04S-CS 1-1123722-04 350mM 3 Harness,SingleGP390-10S-CS 1-1123722-10 300mM 3 Harness,Single1537740-1 1537113-2 1-1123722-4 2

LOC. NO. SW700 SW900

PART NO. 6600VR1004A 6600VR1004A
DESCRIPTION / SPECIFICATION SKHMPWE010 1C1P 12VDC 0.05A HORIZ SKHMPWE010 1C1P 12VDC 0.05A HORIZ

OTHERs

B1 B2 MAY32943836 MAY39568704 68509A0004J EAD35132605 6140VB0004B 6202TST001H 6212AB2872A 6202TST001H 6212AB2883A EAW39040101 6202TST001H 6212AB2883A 6202VDT002H 6202VDT002H EAW39040101 6212AB2015J 6712000014A SAA31073305 SAA31073113 EBD38015101 EBL35311213 EBL35311214 Box, BOX DW 428 NO PRINTING 50PC1/3 Box, BOX DW COLOR (DD-DW6) Cable, Assembly RCA JACK RCA JACK 0.15M 1P BLACK Cable, Assembly SATA CABLE 250MM SATA 7P RED Coil, Choke LN-15A1(26UH) 26uH AC500V 5MA Crystal, SX-1 27MHZ 30PPM 27MHZ 30PPM Crystal, HC49SM 25MHZ 50PPM 20pF HC49SM Crystal, SX-1 27MHZ 30PPM 27MHZ 30PPM Crystal, HC-49SM 27.00000MHZ 27MHZ 30PPM Crystal, 9H03200584 32.768KHZ 20PPM 12.5pF Crystal, SX-1 27MHZ 30PPM 27MHZ 30PPM 20pF Crystal, HC-49SM 27.00000MHZ 27MHZ 30PPM Crystal, SX-1 18.432MHZ 30PPM(16PF) Crystal, SX-1 18.432MHZ 30PPM(16PF) Crystal, 9H03200584 32.768KHZ 20PPM Crystal, HC-49SM 19.66080HZ 19.6608HZ Receiver Module, KSM-2013TH2A.5V 12.4M BK 3P S/W, Firmware 3.10 278C EUROPE FLASH ROM S/W, Firmware 3.07 EFC9 EUROPE FLASH ROM Sensor,Temperature MM3286CFBE 0.3~3.6 SOP 8P Tuner,Tuner/Modulator TAUT-W001D PAL-B/G+I+D/K Tuner,Tuner/Modulator TAFT-W004P PAL-B/G+I+D/K
Harness,SingleSMH200(900MM) SMH200-14(YEONHO) S CA1 Harness,SingleLVDS PDP STANDARD 450MM FI-X30HL( Harness,SingleSMH200 SMH200 800MM 2.00MM 5P UL2 A03-7071-094 D-SUB 15P 2.29MM STR A02-0915-101 D-SUB 9P 2.77MM STRA USB, UAR27-4K2300 A 1P 2.50MM ANGLE DI Wafer, SMW250-13P 13P 2.50MM 1R STRAIGHT Wafer, SMAW200-06P 6P 2.00MM 1R ANGLE DI Wafer, SMW200-14P 14P 2.00MM 1R STRAIGHT Wafer, SMAW200-06P 6P 2.00MM 1R ANGLE DI Wafer, SMAW200-10P 10P 2.00MM 1R ANGLE D Wafer, SMW200-05P 5P 2.00MM 1R STRAIGHT Wafer, SMW250-10P 10P 2.50MM 1R ANGLE DI Wafer, 1-1123723-4 4P 3.96MM 1R STRAIGHT Wafer, 184-0207100-71 7P 1.27MM 1R STRAI Wafer, SMW200-04P 4P 2.00MM 1R STRAIGHT Wafer, SMW200-04P 4P 2.00MM 1R STRAIGHT Wafer, SMW250-03P 3P 2.50MM 1R STRAIGHT Wafer, SMW250-04P 4P 2.50MM 1R STRAIGHT Wafer, 12505WS-04A00 4P 1.25MM 1R STRAIG Wafer, GIL-G-03P-S3T2-E(TYPOE) 3P 2.50MM Wafer, FI-X30SSL-HF 30P 1.00MM 1R ANGLE Wafer, SMW200-10P 10P 2.00MM 1R STRAIGHT Wafer, SMAW200-14P 14P 2.00MM 1R ANGLE D Wafer, SMW200-05P 5P 2.00MM 1R STRAIGHT A1 A1 A1 CA2 L1101 X1200 X1300 X1301 X1301 X1303 X1500 X1500 X400 X401 X501 X700 IC101 IC1306 IC900 IC506 TU200 TU201

ACCESSORY

SAC30653121 MFL39050006 MFL32995402 MKJ39170809 3550V00590A EAD36431301 4972V00178A 3880TKZ004E 4950TKA320A FAB30021701 Title, CD MANUAL MP lan(25) for 37LT81-ZF Manual, Owners LAN(25)+HE MP HYE Simple Book Manual, Owners MF056A LG HYE HE Wty Card-PDP only Remote Controller, COMPLEX ANALOG PVR R/C For Euro Cover, MOLD ABS 50PC3DD-UE.AUSRSHR ABS Power Cord, LP-42 + LS-60L 1.87M 250V Supporter, COMPLEX NON METAL ASSY PDP SET Bag, COMPLEX VINYL 180*150 0.58 H&C MODEL Plate, PRESS SBHG T1.2 SUPPORT UPSET Screw, Machine 1SZZVMR001A RING WALL 5MM 25M
J101 JK100 JK101 JK102 JK1200 JK1201 JK400 JK501 6612J10033A 6612M00010A 6612M00010A 6612J10031A 6612B00015B 6612B00015B 6612J10043A 6612F00099A PMJ016-13 13P DIN/RCA 14MM ANGLE PSC003-01 21P 21P/1C 3.81MM STRAI PSC003-01 21P 21P/1C 3.81MM STRAI PPJ209-02 14.0MM 1RX5C STRAIGHT T DC1R019WDH SOCKET 21P STRAIGHT SM DC1R019WDH SOCKET 21P STRAIGHT SM PPJ200-07 15MM 1RX4C ANGLE BK 3P PEJ024-01 1P 4P STRAIGHT TR 3.6MM

A2 A21 A3 A4 A5 A6 A7

SWITCHs
SW101 SW102 SW103 SW104 SW105 SW106 SW107 SW108 SW1300 140-313B 140-313B 140-313B 140-313B 140-313B 140-313B 140-313B 140-313B 6600VR1004A KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ KPT-1115AM 1C1P 12VDC 0.05A HORIZ SKHMPWE010 1C1P 12VDC 0.05A HORIZ

- 50 -

Copyright 2007 LG Electronics. Inc. All right reserved. Only for training and service purposes

14. HD2SD

J101 PMJ016-13
2A [YL] U-CAN 19A [YL] CONTACT 18A [YL] O-SPRING

READY R103

RR112 0

SIDE A/V(SUB)

P102 SMW200-14

CONTROL B/D(SUB)

P103 SMAW200-10 SW101 140-313B

YIN5 AV_SW VIN5 CIN5

R117 470

KEY2 1

SW102 140-313B

READY ZD101

R101 27K
2B [WH] U-CAN 3B [WH] U-LUG

READY R104

50V 100pF C105

C100 0.1uF

CHSW103 140-313B

R102 7.5K

KEY1 3
2C [RD] U-CAN 19C [RD] CONTACT 18C [RD] 0-SPRING

R109 470

READY ZD100

R103 3K SW104 140-313B

READY R105

50V 100pF C106

9 [DIN] GROUND-TER 17 [DIN] C-LUG-L[DIN] C-LUG-S[DIN] C-LUG-L1

AV__SW VIN5

C101 0.1uF

R111 0

VOL1 IR 2 GND

R104 910

READY R107

YIN5 CIN5

R115 0

READY R106

13 [DIN] C-LUG-S1 11B NC_TER_B 12B COM_TER_B 11D NO_TER_D 11C NO_TER_C 12A COM_TER_A 11A NC_TER_A