Website:http://biz.LGservice.com E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR SERVICE MANUAL

CHASSIS NO. : CA-131

MODEL: StudioWorks 710E (710BK-AL**A)
StudioWorks 710S (710BK-AL**M, AL**B) StudioWorks 710B (710BK-AL**E)
( ) **Same model for Service

CAUTION

BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
*Same looking with new chassis.

Issue Date; 2003. 11.

CONTENTS
SPECIFICATIONS... 2 SAFETY PRECAUTIONS.. 3 TIMING CHART.. 4 OPERATING INSTRUCTIONS.. 5 WIRING DIAGRAM.. 6 DISASSEMBLY.. 7 BLOCK DIAGRAM... 8 DESCRIPTION OF BLOCK DIAGRAM. 9 ADJUSTMENT.. 11 TROUBLESHOOTING GUIDE.. 13 EXPLODED VIEW... 23 REPLACEMENT PARTS LIST. 25 PIN CONFIGURATION.. 30 SCHEMATIC DIAGRAM... 32 PRINTED CIRCUIT BOARD.. 34

SPECIFICATIONS

1. PICTURE TUBE Size DefIection Angle Neck Diameter Stripe Pitch Face Treatment Internal 3-2. Power Consumption : 17 inch : 90 : 29.1 mm : 0.25 mm : W-ARASC (Anti-Reflection and Anti-Static Coating) : Anti-Glare
MODE MAX NORMAL (ON) STAND-BY SUSPEND DPMS OFF POWER CONSUMPTION LED COLOR GREEN GREEN AMBER AMBER AMBER
85 W 73 W less than 15 W less than 15 W less than 5W
2. SIGNAL 2-1. Horizontal & Vertical Sync 1) Input Voltage Level : Low=0~1.2V, High=2.5~5.5V 2) Sync Polarity : Positive or Negative 2-2. Video Input Signal 1) Voltage Level a) Color 0, 0 b) Color 7, 0 c) Color 15, 0 2) Input Impedance 3) Video Color 4) Signal Format
: 0 ~ 0.7 Vp-p : 0 Vp-p : 0.467 Vp-p : 0.7 Vp-p : 75 : R, G, B Analog : Refer to the Timing Chart
4. DISPLAY AREA 4-1. Active Video Area : Max Image Size - 325.1 x 243.8 mm (12.80" x 9.60") Preset Image Size - 310 x 230 mm (12.20" x 9.06") 4-2. Display Color : Full Colors 4-3. Display Resolution : 1280 x 1024 / 60Hz(Max) (Non-Interlace) 4-4. Video Bandwidth : 110 MHz 5. ENVIRONMENT 5-1. Operating Temperature: 0C ~ 40C (Ambient) 5-2. Relative Humidity : 10%~ 90% (Non-condensing) 5-3. Altitude : 5,000 m 6. DIMENSIONS (with TILT/SWIVEL) Width : 400 mm (15.75 inch) Depth : 411 mm (16.18 inch) Height : 397.5 mm (15.65 inch) 7. WEIGHT (with TILT/SWIVEL) Net Weight : 14.0 kg (30.87 lbs.) Gross Weight : 16.8 kg (37.04 lbs.)
2-3. Signal Connector 3 row 15-pin Connector (Attached) 2-4. Scanning Frequency Horizontal Vertical
: 30 ~ 71 kHz : 50 ~ 160 Hz
3. POWER SUPPLY 3-1. Power Range AC 100 - 240V~ 50 / 60Hz, 1.0A

SAFETY PRECAUTIONS

SAFETY-RELATED COMPONENT WARNING! There are special components used in this color monitor which are important for safety. These parts are marked on the schematic diagram and the replacement parts list. It is essential that these critical parts should be replaced with the manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards. Do not modify the original design without obtaining written permission from manufacturer or you will void the original parts and labor guarantee. CAUTION: No modification of any circuit should be attempted. Service work should be performed only after you are thoroughly familiar with all of the following safety checks and servicing guidelines. X-RADIATION The only potential source of X-radiation is the picture tube. However, when the high voltage circuitry is operating properly there is no possibility of an X-radiation problem. The basic precaution which must be exercised is keep the high voltage at the factory recommended level; the normal high voltage is about 25.8KV. The following steps describe how to measure the high voltage and how to prevent X-radiation. Note : It is important to use an accurate high voltage meter calibrated periodically. To measure the high voltage, use a high impedance high voltage meter, connect () to chassis and (+) to the CDT anode cap. Set the brightness control to maximum point at full white pattern. Measure the high voltage. The high voltage meter should be indicated at the factory recommended level. If the meter indication exceeds the maximum level, immediate service is required to prevent the possibility of premature component failure. To prevent X-radiation possibility, it is essential to use the specified picture tube.
SAFETY CHECK Care should be taken while servicing this color monitor because of the high voltage used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits. FIRE & SHOCK HAZARD An isolation transformer must be inserted between the color monitor and AC power line before servicing the chassis. In servicing, attention must be paid to the original lead dress specially in the high voltage circuit. If a short circuit is found, replace all parts which have been overheated as a result of the short circuit. All the protective devices must be reinstalled per the original design. Soldering must be inspected for the cold solder joints, frayed leads, damaged insulation, solder splashes, or the sharp points. Be sure to remove all foreign materials. IMPLOSION PROTECTION All used display tubes are equipped with an integral implosion protection system, but care should be taken to avoid damage and scratching during installation. Use only same type display tubes.

CAUTION:

Please use only a plastic screwdriver to protect yourself from shock hazard during service operation.

TIMING CHART

<< Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc. (s), Vertical etc. (ms) >> Mode
H/V Sort Sync Polarity Frequency Total Period (A) Video Active Time (B) Blanking Time Sync Duration (E) (C) Back Porch (F) Front Porch (D)
Resolution 640x480 75Hz 800x600 75Hz 800x600 85Hz 1024x768 85Hz

H V H V H V H V

+ + + + + +
37.50 74.99 46.88 75.01 53.68 85.07 68.677 85.00
26.67 13.335 21.33 13.331 18.63 11.755 14.561 11.764
20.32 12.802 16.16 12.798 14.22 11.178 10.836 11.182
6.35 0.533 5.17 0.533 4.41 0.577 3.725 0.582
2.03 0.080 1.62 0.064 1.14 0.056 1.016 0.044
3.81 0.427 3.23 0.448 2.70 0.503 2.201 0.524
0.51 0.026 0.32 0.021 0.57 0.018 0.508 0.014

* No Composite Mode.

OPERATING INSTRUCTIONS

FRONT VIEW REAR VIEW

ID Label

See Front Control Panel

Power ON/OFF Button

AC Power Socket

Signal Connector

Front Control Panel

5. MENU Button 3. SELECT Button 2. Power (DPMS) Indicator

Buttons

1. Power Button

1. Power ON/OFF Button

Use this button to turn the monitor ON or OFF.

Button

Use these buttons to choose or adjust items in the on screen display.

2. Power Indicator

This indicator lights up green when the monitor operates normally; in DPMS (Energy Saving) mode, - stand-by, suspend, or power off mode - its color changes to orange, and if abnormal or damaging circuit turns out orange blink.

5. MENU Button

Use this button to enter or exit the on screen display.

3. Select Button

Use this button to enter a selection in the on screen display.

WIRING DIAGRAM

P702 T1

AC Socket

Signal Cable

DISASSEMBLY

1. TILT/SWIVEL & BACK COVER REMOVAL 1) Set the monitor face downward. 2) Carefully remove the Tilt/Swivel by pulling it upward. 3) Pressing the latch (b), Back cover by pushing it upward. 4) Release the latch (c). (See Tip Spec.) 5) Slide the Back Cover away from the Front Cabinet of the monitor.

Ca bin et

Tip Spec. A(Width) : 5.0~15.0mm B(Depth) : 0.6~0.9mm C(Height) : 12.0mm

[ OSD Control ]

H-sync Signal BRIGHTNESS/CONTRAST COLOR CURVE H / V POSITION H / V SIZE SPCC TRAPIZODE PIN BALANCE PARALLELOGRAM TOP CORNER BOTTOM CORNER RECALL DEGAUSSING MOIRE LANGUAGE RESET OSD TIME TILT V-sync Si gnal I 2C DATA (SDA) I 2C CLOCK(SCL) Signal cable R G B

80V Heater ( 6.3V )

VIDEO OSD+pre_Amp (IC302)
VIDEO Main_Amp (IC303) G2 G1 Screen

MICOM (IC401)

I2 C R/G/B Contrast

CUT-OFF IC (IC304)

Dynamic Focus

Static Focus

R/G/B Bias 12V
5V SCL / SDA H/V sync PWM control signal E2PROM (IC402) 15V I2 C H/V Sync I2 C H/V Sync Processor ( IC701 ) TDA4841 15V V-out ( IC601) TDA4867J 15V X-RAY Protection Circuit

BLOCK DIAGRAM

Vertical Blanking, - 160V
6.3V TILT Coil TILT Control Circuit

Voltage feedback

FBT ( T701 ) H-out (Q706) B+ 15V H-Linearity Correction Circuit
H-Drive Degaussing Circuit 15V

80V Degaussing Coil

Line Filter
400V Dynamic FOCUS Circuit Auto Beam Limit

SMPS (T901)

5V 6.3V 15V
DC/DC Converter B-Drive 50V
Voltage feedback Input_power 100~240VA C (50/60Hz)

D/D Feed Back

Power Control (IC901)

DPM Control Circuit

Regulation Circuit
DESCRIPTION OF BLOCK DIAGRAM
1. Line Filter & Associated Circuit. This is used for suppressing noise of power input line flowing into the monitor and/or some noise generated in this monitor flowing out through the power input line. That is to say, this circuit prevents interference between the monitor and other electric appliances. 2. Degauss Circuit & Coil. The degauss circuit consists of the degaussing coil, the PTC(Positive Temperature Coefficient) thermistor(TH901), and the relay(RL901). This circuit eliminates abnormal color of the screen automatically by degaussing the shadow mask in the CRT during turning on the power switch. When you need to degauss in using the monitor, select DEGAUSS on the OSD menu. 3. SMPS(Switching Mode Power Supply). This circuit is working of 90~264V AC(50/60Hz). The operation procedure is as follows: 1) AC input voltage is rectified and smoothed by the bridge diodes (D900) and the capacitor (C908). 2) The rectified voltage(DC) is applied to the primary coil of the transformer(T901). 3) The control IC(IC901) generates switching pulse to turn on and off the primary coil of the transformer (T901) repeatedly. 4) Depending on turn ratio of the transformer, the secondary voltages appear at the secondary coils of the transformer(T901). 5) These secondary voltages are rectified by each diode(D941, D942, D951, D961, D971) and operate other circuit. (horizontal and vertical deflection, video amplifier,.etc.) 4. X-ray Protection. If the high voltage of the FBT reaches up to 29kV (abnormal state), IC401(MICOM) pin 35 Sensing from FBT directly. Then MICOM control IC701 (Deflection controller) to stop Horizontal drive pulse and stop Horizontal Deflection. 5. Micom(Microprocessor) Circuit. The operating procedure of Micom(Microprocessor) and its associated circuit is as follows: 1) H and V sync signal is supplied from the signal cable. 2) The Micom(IC401) distinguishes polarity and frequency of H and V sync. 3) The Micom sets operating mode and offers the controlled data. (H-size, H-position, V-size,. etc.) 4) The controlled data of each mode is stored in itself. 5) User can adjust screen condition by each OSD function. The data of the adjusted condition is stored in EEPROM(IC402). 6. Horizontal and Vertical Oscillation. This circuit generates the horizontal pulse and the vertical pulse by taking the H and V sync signal. This circuit consists of the TDA4867(IC601) and the associated circuit. 7. D/D(DC to DC) Converter. This circuit supplies DC voltage to the horizontal deflection output circuit by increasing DC 50V which is the secondary voltage of the SMPS in accordance with the input horizontal sync signal. 8. Side-Pincushion & Trapezoid Correction Cirucit. This circuit improves the side-pincushion and the trapezoid distortion of the screen by mixing parabola and saw-tooth wave to output of the horizontal deflection D/D converter which is used for the supply voltage(B + ) of the deflection circuit. 9. Horizontal Deflection Output Circuit. This circuit makes the horizontal deflection by supplying the saw-tooth current to the horizontal deflection yoke. 10. High Voltage Output & FBT(Flyback Transformer). The high voltage output circuit is used for generating pulse to the primary coil of the FBT(Flyback Transformer) secondary of the FBT and it is supplied to the anode, focus, and screen voltage of the CRT. 11. H-Linearity Correction Circuit. This circuit corrects the horizontal linearity for each horizontal sync frequency. 12. Vertical Output Circuit. This circuit takes the vertical ramp wave from the TDA4841(IC701) and performs the vertical deflection by supplying the saw-tooth current to the vertical deflection yoke. 13. Dynamic Focus Output Circuit. This circuit takes the horizontal and the vertical parabola waves from the TDA4841(IC701) and amplifies it to maintain constant focus on center and corners in the screen. 14. H & V Blanking and Brightness Control. Blanking circuit eliminates retrace line by supplying negative pulse to the G1 of the CRT. And Brightness circuit is used for control of the screen brightness by changing DC level of the G1.

15. Image Rotation (Tilt) Circuit. This circuit corrects the tilt of the screen by supplying the image rotation signal to the tilt coil which is attached near the deflection yoke of the CRT. 16. Video Pre-Amp Circuit. This circuit amplifies the analog video signal from 0-0.7V to 0-4V. It is operated by taking the clamp, R, G, B drive and contrast signal from the Micom(IC401).
17. Video Output Amp Circuit. This circuit amplifies the video signal which comes from the video pre-amp circuit and amplified it to applied the CRT cathode.

- 10 -

ADJUSTMENT

GENERAL INFORMATION

All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes several adjustments may be required. Adjustment should be following procedure and after warming up for a minimum of 30 minutes. Alignment appliances and tools. - IBM compatible PC. - Programmable Signal Generator. (eg. VG-819 made by Astrodesign Co.) - EPROM or EEPROM with saved each mode data. - Alignment Adaptor and Software. - Digital Voltmeter. - White Balance Meter. - Luminance Meter. - High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSING The degaussing coil is mounted around the CDT so that automatic degaussing when turn on the monitor. But a monitor is moved or faced in a different direction, become poor color purity cause of CDT magnetized, then press DEGAUSS on the OSD menu.
7) Adjust tilt as arrow keys to be the best condition. 8) DIST. ADJ. BALANCE command. 9) Adjust parallelogram as arrow keys to be the best condition. 10) Adjust balance of pin-balance as arrow keys to be the best condition. 11) DIST. ADJ. FOS. ADJ command. 12) Adjust V-SIZE as arrow keys to 2302mm. 13) Adjust V-POSITION as arrow keys to center of the screen. 14) Adjust H-SIZE as arrow keys to 3102mm. 15) Adjust H-POSITION as arrow keys to center of the screen. 16) Adjust S-PCC (Side-Pincushion) as arrow keys to be the best condition. 17) Adjust TRAPEZOID as arrow keys to be the best condition. 18) Save of the Mode 1~4. 19) Display from Mode 2 to 4 and repeat above from number 12) to 19) 20) PRESET EXIT Y (Yes) command. 4. Adjustment for White Balance and Luminance. 1) Set the White Balance Meter. 2) Press the DEGAUSS on the OSD menu for demagnetization of the CDT. 3) COLOR ADJ. LUMINANCE command of the alignment program. 4) Set Brightness and Contrast to Max position. 5) Display color 0,0 pattern at Mode 4. 6) COLOR ADJ. BIAS ADJ. COLOR No. 1 command of the alignment program. 7) Check whether green color or not at R-BIAS and GBIAS to min position and B-BIAS to 127(7F) position and Sub-Brightness to 205(CD) position. Adjust G2 (screen) command to 0.4 0.05FL of the raster luminance. 8) Adjust R-BIAS and G-BIAS command to x=0.283 0.005 and y=0.298 0.005 on the White Balance Meter with PC arrow keys. 9) Adjust SUB-Brightness command to 0.40.1FL of the raster luminance. 10) Adjust repeat number 8). 11) After push the ENTER key. 11-1) COMMAND PRESET START Y(Yes) command. 12) Display color 15,0 full white pattern at Mode 4. 13) DRIVE ADJ. No 1. command.

ADJUSTMENT PROCEDURE & METHOD
- Install the cable for adjustment such as Figure 1and run the alignment program on the DOS for IBM compatible PC. - Set external Brightness and Contrast volume to max position. 1. Checked for B+ Voltage. 1) Display cross hatch pattern at Mode 4. 2) Check D961 voltage to 50.0V 1V with. 2. Adjustment for High-Voltage. 1) Display cross hatch pattern at Mode 4. 2) DIST.ADJCTRL PWM High Voltage Command. 3) Adjust High Voltage to 25.8kV0.1 kVdc. 4) Press Enter Key. 3. Adjustment for Factory Mode (Preset Mode). 1) Display cross hatch pattern at Mode 1. 2) Run alignment program for 710BK on the IBM compatible PC. 3) EEPROM ALL CLEAR Y(Yes) command. <Caution> Do not run this procedure unless the EEPROM is changed. All data in EEPROM (mode data and color data) will be erased. 4) Power button of the monitor turn off turn on. 5) COMMANDPRESET STARTY(Yes) command. 6) DIST. ADJ. CTRL PWM TILT command.

- 11 -

14) Set Brightness and Contrast to Max position. 15) Set SUB-CONTRAST 127(7F) (decimal) position. 16) Set B-DRIVE to 85(55) at DRIVE of the alignment program. 17-1) Adjust R-DRIVE and G-DRIVE command to white balance x=0.2830.003 and y=0.2980.003 on the White Balance Meter with PC arrow keys. 17-2) Display color 15,0 window pattern (70x70mm) at mode 4. 18) Adjust SUB-CONTRAST command to 502FL. 19) After push the ENTER key. 20) Display color 15,0 full white patten at Mode 4. 21) COLOR ADJ. LUMINANCE ABL command. 22) Adjust ABL to 321FL of the luminance. 23) After push the ENTER key, and COMMAND PRESET EXIT Y(Yes) command. 24) Exit from the program.
5. Input EDID Data. 1) Display color 15,0 cross hatch pattern at Mode 4. 2) EEPROM Write EDID command and confirm EDID Write OK!! message of monitor. 3) Exit from the alignment program. 4) Power switch OFF/ON for EDID data save. 6. Adjustment for Focus. 1) Set the Brightness and Contrast to max position. 2) Display H character in full screen at Mode 4. 3) Adjust two Focus control on the FBT that focus should be the best condition.

- 12 -

TROUBLESHOOTING GUIDE

1. NO POWER

NO POWER (POWER INDICATOR OFF)

CHECK FUSE OK?

TROUBLE IN FUSE (F901)
CHECK C908 VOLTAGE? (AC120V: 160VDC, AC220V: 304VDC)

TROUBLE IN D900

CHECK IC901 PIN 6 WAVEFORM ?

TROUBLE IN Q901

CHECK D941, D942, D951, D961, D971 VOLTAGE?
TROUBLE IN D941, D942, D951, D961, D971
TROUBLE IN Q903, Q952, Q951, Q942, Q941

- 13 -

2. NO CHARACTER

NO CHARACTER

CHECK IC302 PIN 18(5V) ? YES

TROUBLE IN P302 5V LINE

CHECK IC302 PIN 5, 6, 7?
TROUBLE IN PC SIGNAL, P301 SIGNAL CABLE
CHECK IC302 PIN 19, 20, 21 ?

TROUBLE IN IC302

YES CHECK IC303 PIN 4 (80V) PIN 8 (12V) ?
TROUBLE IN P303 12V LINE/ 80V LINE
CHECK IC303 PIN 1, 2, 3 ?

TROUBLE IN IC303

YES CHECK R, G, B CATHODE VOLTAGE? YES TROUBLE IN CRT SOCKET TROUBLE IN R331~R333, L311~L313, D307~D312

- 14 -

3. NO RASTER
NO VIDEO (POWER INDICATOR ON)
CHECK POWER INDICATOR GREEN or AMBER?
DPM MODE (NO H and/or V SYNC)
CHECK D712 ANODE (-160V)?

TROUBLE IN D712

CHECK G1 VOLTAGE? (-55V~-15V)

TROUBLE IN Q799

CHECK CDT HEAT VOLTAGE? (6.3V)
TROUBLE IN D941, Q942, Q941

TROUBLE IN CDT

- 15 -
4. NO HORIZONTAL DEFLECTION
NO H-DEFLECTION (ONE VERTICAL LINE)

CHECK Q706?

TROUBLE IN Q706

CHECK B+ VOLTAGE (50V)?

TROUBLE IN 50V LINE
CHECK T701(FBT) PIN 2 (31KHZ 60V, 69KHZ 140V) ?
TROUBLE IN Q719, Q720, D710
CHECK Q705 COLLECTOR WAVEFORM?

TROUBLE IN Q705

TROUBLE IN T701, P701

- 16 -

5. TROUBLE IN H-LINEARITY

UNBALANCED OF H-LIN.

CHECK IC401 PIN 6, 7, 8 ?

TROUBLE IN IC401 (MICOM)

CHECK Q711~Q716?

TROUBLE IN Q711 ~ Q716

CHECK L703?

TROUBLE IN L703

Cs SIGNAL TABLE

HORIZONTAL FREQUENCY(fH)

Cs1 L L H H H H H H H

Cs2 L L L L H H H H H

Cs3 L H L L L L L H H
TROUBLE IN C722, C723, C726, C729
30K 34K 39K 44K 49K 52K 58K 62K 66K

~ ~ ~ ~ ~ ~ ~ ~ ~

33.9K 38.9K 43.9K 48.9K 51.9K 57.9K 61.9K 65.9K 71K

- 17 -

6. NO VERTICAL DEFLECTION
NO V-DEFLECTION (ONE HORIZONTAL LINE)
CHECK IC601 PIN 2 (15V+)?

TROUBLE IN D951 15V LINE

CHECK IC701 PIN 12, 13?

TROUBLE IN IC701

12Pin 13Pin
TROUBLE IN IC601, V-CIRCUIT

- 18 -

7. TROUBLE IN OSD

NO OSD

(ENTER BUTTON MUST BE PRESSED.)
CHECK IC302 B+ (5V) ? DC 5V YES

TROUBLE IN 5V LINE

CHECK IC302 PIN 1, 24 WAVEFORM?

TROUBLE IN IC401 PIN29 (V-FBP), IC701V LINE (H-FBP)

Pin 24

TROUBLE IN OSD PERIPHERAL CIRCUIT

- 19 -

8. TROUBLE IN DPM

OFF MODE FAILURE

(NO OFF MODE.)
CHECK IC401 (MICOM) PIN 30, 31 (H/V INPUT) SIGNAL?

INPUT H/V SYNC SIGNAL

CHECK PC, (PC IS NOT GOING INTO DPM OFF MODE)

H/V SYNC

CHECK IC401 PIN 12, 13 WAVEFORM?

TROUBLE IN X401

CHECK IC401 (MICOM) PIN 2, 3 ? SEE DPM TABLE YES

(DPMF: 0V)

CHECK B+ LINE (6.3V,15V+, 80V) ?
TROUBLE IN Q941, Q942, Q951, Q952,
YES Mode TROUBLE IN PC Item DPMF H L L L
DPM TABLE DPMS H H H L LED GREEN AMBER AMBER AMBER
NORMAL STAND-BY SUSPEND OFF

- 20 -

9. NO DEGAUSSING

NO DEGAUSSING

(DEGAUSS ON THE OSD MENU MUST BE PRESSED.)

CHECK IC401 PIN 5 (0V)?

CHECK Q953 COLLECTOR VOLTAGE? DC 15V YES

TROUBLE IN Q953

CHECK P902 ?

TROUBLE IN P902

CHECK RL901?

TROUBLE IN RL901

YES TROUBLE IN TH901, DEGAUSSING COIL

- 21 -

10. NO TILT (NO ROTATION )

NO TILT (NO ROTATION)

CHECK IC401 PIN21 WAVE FORM ?
CHECK 15V LINE AND 6.3V LINE ?
TROUBLE IN 15V LINE, 6.3V LINE
CHECK Q503 EMITTER VOLTAGE ?

TROUBLE IN Q501~Q503

TROUBLE IN P501, TILT COIL

- 22 -

EXPLODED VIEW

- 23 -

SE LE CT

EXPLODED VIEW PARTS LIST

Ref. No. Part No.
3091TKC099C 3091TKC099E 3091TKC099B 3091TKC099D 6318L17026C 6318L17026B 6318L17026E 6318L17024A 3809TKC050C 3809TKC050B 3043TKK129A 3043TKK129B 339-002H 6140TC3004G 6174T11005E 6620TKB002D or 6620TKB002B 6850TA9012A 4950TKS155S 4950TKS212D 4810TKK150A 4810TKK151A 332-102F 4810TKK204J 4930TKK031C 4810TKK200A 3313T17335G 3313T17335B 3313T17335C Description CABINET ASSEMBLY, 710BJ BRAND C083 320T,89483,S/W710E,DI(SPRING CKD) -(S/W 710E) CABINET ASSEMBLY, 710BK BRAND C083 320T,89483,S/W710E,LG RED,DI -For Panama(S/W 710E) CABINET ASSEMBLY, 710BJ BRAND C083 S/W 700S,320T,89483,SPRING CKD,DI -(S/W 710S) CABINET ASSEMBLY, 710BJ BRAND C083 PC+ABS,89483,S/W710B,MAADIRAN -(S/W 710B) CDT(CIRC), M41LFQ503X00NDDV LG-PHILIPS DISPLAYS 70KHZ 29.1MM FST GLARE PLUS BARE -For Northern Hemisphere(S/W 710E) CDT(CIRC) M41LFQ803X00NDDV LG-PHILIPS DISPLAYS 70KHZ 29.1MM FST MPR PLUS BARE -For Equatorial (S/W 710S) CDT(CIRC), M41LFQ803X00SDDV LG-PHILIPS DISPLAYS 70KHZ 29.1MM FST MPR PLUS BARE -For Southern Hemisphere(S/W 710S) CDT(CIRC), M41LFQ803X61NDDP LG-PHILIPS DISPLAYS 70KHZ 29.1MM FST TCO PLUS -For Iran(S/W 710B) BACK COVER ASSEMBLY, T710 C046 320T,EQ54(8C358) -For World Wide(S/W 710E, 710S) BACK COVER ASSEMBLY, T710BH/PH C046 GN5008HF,8C358(EQ54) -For Iran(S/W 710B) TILT SWIVEL ASSEMBLY, 710BJ T068/B060 60HR,8C358 -For World Wide(S/W 710E, 710S) TILT SWIVEL ASSEMBLY, 710BJ T068/060 60HR,8C358 MAADIRAN CKD -For Iran(S/W 710B) SCREW ASSY, PHP+5*20(FZMY)+GW18 NEW TYPE COIL, DEGAUSSING, 16.0OHM 0.35MM 80T 17" L1090MM,WITH EARTH 700BJ FBT(FLY BACK TRANSFORMER), CF2154/F700BK(17"/71K,FLAT,FCDT,FST) LIEN CHANGE 17" SOCKET(CIRC), POWER, CDJ-3C DUOLING AC UNIVERSAL 3PIN BLACK SOCKET(CIRC), POWER, SA-4S HUA JIE AC UNIVERSAL 3PIN BLACK CABLE,D-SUB, UL20276-9C(5.8MM) AT 1500MM GRAY(85964) T710BJ DM METAL, SHIELD BOTTOM,CB553,0.8T,REAR HOLE DELETE -For World Wide(S/W 710E, 710S) METAL, SHIELD BOTTOM C-CKD -For Iran(S/W 710B) BRACKET, CN771C SUPPORTER BOT.(RIGHT) BRACKET, CN771C SUPPORTER BOT.(LEFT) SCREW, PTP+4*20BP(MSWR/FZMY) BRACKET, 700BK HOLDER FBT H-CKD HOLDER, PCB FIX , PC+ABS BRACKET, KNOB SUPPORTER CN772G NECCI MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For Saudi, Africa(S/W 710E) MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For Asia(S/W 710E) MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For Asia(S/W 710S) MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For Austrailea(S/W 710S) MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For S.Africa(S/W 710S) MAIN TOTAL ASSEMBLY, 710BK BRAND CA-131 -For India(S/W 710S) MAIN TOTAL ASSEMBLY, 710BK.KLIOEI BRAND CA-131 -For Iran(S/W 710B) PWB(PCB) ASSEMBLY, MAIN, 710BK KLEUAD BRAND CA-131 TOTAL -For Saudi, Africa(S/W 710E) PWB(PCB) ASSEMBLY, MAIN, 710BK KLDAAD BRAND CA-131 TOTAL -For Asia(S/W 710E) PWB(PCB) ASSEMBLY, MAIN, 710BK KLDAMD BRAND CA-131 TOTAL -For Asia(S/W 710S) PWB(PCB) ASSEMBLY, MAIN, 710BK KLAUMD BRAND CA-131 TOTAL -For Austrailea(S/W 710S) PWB(PCB) ASSEMBLY, MAIN, 710BK KLZAMD BRAND CA-131 TOTAL -For S.Africa(S/W 710S) PWB(PCB) ASSEMBLY, MAIN, 710BK KLIDMD BRAND CA-131 TOTAL -For India(S/W 710S) PWB(PCB) ASSEMBLY, MAIN, 710BK KLIOEI BRAND CA-131 TOTAL -For Iran(S/W 710B) SCREW, DRAWING, D3.5 L10.0 MSWR/FZMY +SW3.5+RW3.5 SCREW ASSEMBLY, TAPTITE P TYPE D3.0 L10.0 MSWR/FZMY SW3+RW10 SCREW, DRAWING, PZP+3*10(MSWR/FZMY) SCREW, PVP+3*16(MSWR/FZMY) SCREW, PZP+3*8 (MSWR/FZMY)

11-1 11-15

3313T17335D 3313T17335E 3313T17335F 3313T17335H 6871TMT508G 6871TMT508B 6871TMT508C
6871TMT508D 6871TMT508E 6871TMT508F 6871TMT508H

a b c d e

332-112F 4001TKK004E 332-095B 332-113H 332-095A

- 24 -

REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE : S SAFETY Mark AL ALTERNATIVE PARTS

*S *AL LOC. NO.

PART NO.
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION

*S *AL LOC. NO. C599

PART NO. 0CE225CK638 0CE227CH638 181-288K 0CE476EK638 0CZZTFT001V 0CK1020W515 0CQ4721N419 0CZZTFT001M 0CZZTFT001Z 0CQ8221N519 0CZZTFT001Z 0CZZTFT002B 0CE227CH638 0CZZTFT001Z 0CQ5621N419 0CK2210K515 0CE107CH638 181-288N 0CK2710K515 0CZZTFT001R 0CZZTFT001V 0CZZTAB001F 0CK27101515 181-303R 181-305C 0CK1040K945 0CK8210W515 181-482F 0CK1040K945 181-305W 0CK1040K945 0CBZTBU004H 181-288N 0CBZTBU003H 0CE226CK638 0CK1030K945 0CK10102515 181-302L 0CE106CK638 0CE227EL630 0CZZTFT002B 0CE106CK638 0CZZTFT002B 0CZZTAB005A 0CK5610W515 0CK3310W515 0CK1040K945 0CK1510W515 0CE105CQ638
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION 2.2UF SHL,SD 50V M FM5 TP 5 220UF SHL,SD 25V M FM5 TP 5 MKT 100V 683JTR PHS26683 47UF KMG 50V M FM5 TP 5 ECQB1H473JM3 473J 50V TP5.0 1000P 500V K B TS 0.0047U 100V J POLY NI TP5 ECQB1H103JF3 MATSUSHITA 50V ECQB1H104JM3 104J 50V TP5.0 0.0082UF D 100V 10% PE NI TP ECQB1H104JM3 104J 50V TP5.0 ECQV1H154JZ3 154J 50V TP5.0 220UF SHL,SD 25V M FM5 TP 5 ECQB1H104JM3 104J 50V TP5.0 5600PF D 100V 5% PE NI TP5 220P 50V K B TS 100UF SHL,SD 25V M FM5 TP 5 MKT 100V 103JTR PHS86103 270P 50V K B TS ECQB1H223JM3 223J 50V TP5.0 ECQB1H473JM3 473J 50V TP5.0 SHL-BP SYE / SWE 50V 3.3UF 2 270P 1KV K B TS 304J 31.0*21.0*13.0*20.154J 19.0*14.0*8.0*10.0 250V 0.1UF 50V Z F TR 820P 500V K B TS 274JF 18.0*17.0*10.0*7.0.1UF 50V Z F TR 604J 26.0*19.0*12.5*15.0.1UF 50V Z F TR 5600PF D 2.5KV H M/PP NI FM2 MKT 100V 103JTR PHS86103 362J 20.0*12.0*7.0*10.0 800V 22UF SHL,SD 50V M FM5 TP 5 0.01UF 50V Z F TR 100PF D 2KV 10% B(Y5P) TR 682J 19.5*12.0*7.0*10.0 250V 10UF SHL,SD 50V M FM5 TP 5 220UF KMG 63V M FM5 BULK ECQV1H154JZ3 154J 50V TP5.0 10UF SHL,SD 50V M FM5 TP 5 ECQV1H154JZ3 154J 50V TP5.0 SMSHR SYE / SWE 160V 47UF 20 560P 500V K B 0.1UF 50V Z F TR 150PF 500V K B TR 1UF SHL,SD 200V M FM5 TP 5 TS 330P 500V K B TS

*S *AL LOC. NO. D404 D704 D705 D706 D710 D711 D712 D714 D715 D716 D717 D718 D719 D720 D721 D722 D723 D724 D730 D731 D768 D801 D802 D900 D904 D905 D906 D908 D910 D911 D941 D942 D951 D952 D961 D971 ZD402 ZD403
PART NO. 971-0054 0DRFC00010A 0DRGF00069A 0DRFC00010A 0DR400409AC 0DSGF00019A 0DR100009CA 0DSGF00019A 0DSGF00019A 0DR140059AD 0DR140059AD 0DR140059AD 0DR100009DA 0DSGF00019A 0DR100009CA 0DSGF00019A 0DSGF00019A 0DR140059AD 0DSGF00019A 0DSGF00019A 0DR100009DA 0DSGF00019A 0DSGF00019A 0DRTW00121A 0DR100009CA 0DD400709CB 0DR100009CA 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DR100009LD 0DR400409AC 0DRGF00150A 0DSGF00019A 0DRGS00090A 0DD400709CB 0DZ560009AG 0DZ560009AG 0DZ560009AG 0DZ560009AG 0DZ560009AG 0DZ560009AG 0DZ120009BF 0DZ510009BE
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION TIN 50MM TAPING FFPF04F150S FAIR CHILD ST TO SB140 GULF TP DO41 40V 1A 40 FFPF04F150S FAIR CHILD ST TO UF4004 GULF TP DO41 400V 1A 1N4148 GULF TP DO35 100V 0.1 RGP10G TP GULF SEMICONDUCTOR 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4005 GULF TP DO41 600V 1A 1N4005 GULF TP DO41 600V 1A 1N4005 GULF TP DO41 600V 1A RGP10J TP GULF SEMICONDUCTOR 1N4148 GULF TP DO35 100V 0.1 RGP10G TP GULF SEMICONDUCTOR 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4005 GULF TP DO41 600V 1A 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 RGP10J TP GULF SEMICONDUCTOR 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 D2SB60-1121 TIWAN SEMI ST GB RGP10G TP GULF SEMICONDUCTOR UF4007 TP G.I DO204AL 1000V RGP10G TP GULF SEMICONDUCTOR 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 UG1D GULF TP DO41 200V 1A 40 UF4004 GULF TP DO41 400V 1A UF5404 GULF BK DO201AD 400V 1N4148 GULF TP DO35 100V 0.1 31GF6L-5701 GENERAL SEMICOND UF4007 TP G.I DO204AL 1000V GDZJ5.6B TP GRANDE DO-GDZJ5.6B TP GRANDE DO-GDZJ5.6B TP GRANDE DO-GDZJ5.6B TP GRANDE DO-GDZJ5.6B TP GRANDE DO-GDZJ5.6B TP GRANDE DO-GDZJ12B TP GRANDE DO34 0.5W GDZ5.1B TP GRANDE DO34 500MW

DIODEs

D201 D301 D302 D303 D304 D305 D306 D307 D308 D309 D310 D311 D312 D313 D314 D315 D316 D402 0DLGP0010AB 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DSGF00019A 0DS124409AA 0DS124409AA 0DS124409AA 0DS124409AA 0DS124409AA 0DS124409AA 0DR140059AD 0DSGF00019A XIAMEN G&P GP32052ME/512-ZY1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1N4148 GULF TP DO35 100V 0.1 1SS244 TP ROHM KOREA 1SS244 TP ROHM KOREA 1SS244 TP ROHM KOREA 1SS244 TP ROHM KOREA 1SS244 TP ROHM KOREA 1SS244 TP ROHM KOREA 1N4005 GULF TP DO41 600V 1A 1N4148 GULF TP DO35 100V 0.1

ZD404 ZD405 ZD407 ZD410 ZD701 ZD902
IC302 IC303 IC304 IC401 IC402 IC601 IC701 IC701
0IPRPNS025B 0IPRPNS026A 0IPRPNS005A 0IMCRSS032B 0ISG240860A 0IPRPPH018A 0IPRPPH005A 0IPRPPH005A
LM1246DDB/NA NATIONAL SEMICO LM2445TA NATIONAL SEMICONDUC LM2480NA NATIONAL SEMICONDUC LGM31B-160/BBS SAMSUNG ELECT M24C08-BN6 8DIP BK 8K SERIAL TDA4867J PHILIPS 9PIN,ST DIP TDA4841PS PHILIPS 32P,SDIP S TDA4841PS PHILIPS 32P,SDIP S

- 26 -

*S *AL LOC. NO. R314
PART NO. 0RD1000Q609 0RD1000Q609 0RD4701Q609 0RD4701Q609 0RD2201Q609 0RD1001Q609 0RD1001Q609 0RD1001Q609 0RD1001Q609 0RD1600Q609 0RD1600Q609 0RD1600Q609 0RD3303Q609 0RD3303Q609 0RD3303Q609 0RD1000Q609 0RD0102Q609 0RN1002F409 0RD0332A609 0RD0332A609 0RD0332A609 0RD0332Q609 0RD0332Q609 0RD0332Q609 0RD1200Q609 0RD1000Q609 0RD5600Q609 0RD1002Q609 0RD2001Q609 0RD2001Q609 0RD1300Q609 0RD1300Q609 0RD1000Q609 0RD3901Q609 0RD1004Q609 0RD1301Q609 0RD4701Q609 0RD1000Q609 0RD1002Q609 0RD1004Q609 0RD3001Q609 0RD2200Q609 0RD4701Q609 0RD4701Q609 0RD1000Q609 0RD1000Q609 0RD1000Q609 0RD1000Q609 0RD1000Q609 0RD1000Q609 0RD1001Q609 0RD2200Q609 0RD2200Q609 0RD0912Q609 0RD1002Q609 0RD1001Q609
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION 100 1/4W(3 5% TA1/4W(3 5% TA52 4.70K 1/4W(3 5% TA52 4.70K 1/4W(3 5% TA52 2.20K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52 1K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 330K 1/4W(3 5% TA52 330K 1/4W(3 5% TA52 330K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 10K 1/6W 1 TAOHM 1/2 W (7.0) 5% TAOHM 1/2 W (7.0) 5% TAOHM 1/2 W (7.0) 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 10K 1/4W(3 5% TA52 2K 1/4W(3 5% TA52 2K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 3.90K 1/4W(3 5% TA52 1M OHM 1/4 W (3.4) 5% TA52 1.30K 1/4W(3 5% TA52 4.70K 1/4W(3 5% TA1/4W(3 5% TA52 10K 1/4W(3 5% TA52 1M OHM 1/4 W (3.4) 5% TA52 3K 1/4W(3 5% TA1/4W(3 5% TA52 4.70K 1/4W(3 5% TA52 4.70K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 1K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TAOHM 1/4 W (3.4) 5% TA52 10K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52

COILs & COREs

L301 L302 L303 L311 L312 L313 L702 L703 L705 L901 L903 FB701 FB703 FB705 FB903 FB904 FB905 FB906 FB921 FB922 971-0054 971-0054 971-0054 0LA0680K119 0LA0680K119 0LA0680K119 6140TBZ025D 6140TYZ010G 6140TBZ026C 6200TZZ004A 6210TCE003K 6210TCE003L 971-0054 971-0054 6210TCE003P 971-0054 6210TCE003J 6210TCE003P 6210TCE003A 6210TCE003A TIN 50MM TAPING TIN 50MM TAPING TIN 50MM TAPING 0.68UH K 2.3*3.4 TP 0.68UH K 2.3*3.4 TP 0.68UH K 2.3*3.4 TP - - H-SIZE,DR12*20-C6.0,150U LX31 GET DR14*15-C5.2,16.5T, DR15*18-C9.8 100UH 0.1*30MM SQE2626 NAMYANG BK L/FILTER BAS3550T BO SUNG 3550MM AXIA BAS3580T BO SUNG 3580MM AXIA TIN 50MM TAPING - Only(S/W 710S) TIN 50MM TAPING BRS2550B BO SUNG 2550MM RADI TIN 50MM TAPING BAS2550T BO SUNG 2550MM AXIA BRS2550B BO SUNG 2550MM RADI BRD3510B BO SUNG 3510MM RADI BRD3510B BO SUNG 3510MM RADI R315 R319 R320 R326 R327 R328 R329 R330 R331 R332 R333 R334 R335 R336 R337 R338 R340 R341 R342 R343 R344 R345 Q501 Q502 Q503 Q705 Q706 Q707 Q708 Q709 Q710 Q711 Q712 Q713 Q714 Q715 Q716 Q719 Q720 Q722 Q723 Q799 Q901 Q903 Q941 Q942 Q951 Q952 Q953 0TR320209AA 0TR127009AA 0TR319809AA 0TR200009AB 0TRFC10008A 0TR127009AA 0TR127009AA 0TRFC10010A 0TRKE90020A 0TF630001BB 0TF630001BB 0TF630001BB 0TR319809AA 0TR319809AA 0TR319809AA 0TFFC10012A 0TR390409CA 0TR319809AA 0TR127009AA 0TRKE90019A 0TF760000AD 0TR100809AA 0TR319809AA 0TR127309AA 0TR319809AA 0TR127309AA 0TR319809AA KTC3202-Y(KTC1959) TP KEC TO KTA1270-Y(KTA562TM) TP KEC T KTC3198-Y(KTC1815) TP KEC TO KTC200-Y TP KEC TO92 NPN FJAF5804(TU) FAIRCHILD ST TO KTA1270-Y(KTA562TM) TP KEC T KTA1270-Y(KTA562TM) TP KEC T KSD1589Y FAIRCHILD ST TO220F MPSA44 KEC TP TO92 500V 300M SGS-T(STM) IRF630MFP ST TO22 SGS-T(STM) IRF630MFP ST TO22 SGS-T(STM) IRF630MFP ST TO22 KTC3198-Y(KTC1815) TP KEC TO KTC3198-Y(KTC1815) TP KEC TO KTC3198-Y(KTC1815) TP KEC TO FQPF10N20C FAIRCHILD ST TO22 FAIRCHILD 2N3904(TA) TP TO-9 KTC3198-Y(KTC1815) TP KEC TO KTA1270-Y(KTA562TM) TP KEC T MPSA92 KEC TP TO92 -300V -50 SSS7N60B FAIRCHILD ST TO220F KSC1008C-Y TP SAMSUNG TO92 KTC3198-Y(KTC1815) TP KEC TO KTA1273-Y(KTA966A) TP KEC TO KTC3198-Y(KTC1815) TP KEC TO KTA1273-Y(KTA966A) TP KEC TO KTC3198-Y(KTC1815) TP KEC TO R346 R347 R401 R402 R403 R405 R406 R407 R408 R409 R411 R412 R415 R416 R417 R418 R419 R420 R424 R425 R426 R429 R430 R431 R432 R433 R434 R438 R441 R442 R301 R302 R303 R305 0RD0752Q609 0RD0752Q609 0RD0752Q609 0RN6201F1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 6.20K 1/6W 1% TA52 R443 R446 R447

PART NO. 0RD1000Q609 0RD2402Q609 0RD2702Q509 0RD2700A609 0RD4702Q609 0RD2201Q609 0RD3001Q609 0RD4702Q609 0RD2201Q609 0RD3001Q609 0RD0222A609 0RD2201Q609 0RD3001Q609 0RX4300K607 0RD0471Q609 0RD2202A609 971-0054 0RN1303F409 0RD1002Q509 0RD3001Q609 0RD3001Q609 0RD3001Q609 971-0054 0RD3000A609 0RD1501Q609 0RD5103A609 0RN1001F409 0RD1501Q609 0RD1802Q509 0RD3302A609 0RD2001Q609 0RD3001Q509 0RD3301A609 971-0054 0RD1000Q609 0RD4702Q609 0RD1501Q609 0RD2001Q609 0RD1502Q609 0RD1802Q609 0RD1502Q609 0RD1001Q609 0RD2001Q609 0RD4702Q609 0RD7502Q609 0RX0101K665 0RD4302Q609 0RD1002Q609 0RN3301F409 0RN6202F409 0RN8202F409 0RD1002Q609 0RD4703A609 0RD0332Q609 0RN1800F409 0RX3902K665
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION 100 1/4W(3 5% TA52 24K 1/4W(3 5% TA52 27K OHM 1/4 W(3.4) 2% TAOHM 1/2 W (7.0) 5% TA52 47K 1/4W(3 5% TA52 2.20K 1/4W(3 5% TA52 3K 1/4W(3 5% TA52 47K 1/4W(3 5% TA52 2.20K 1/4W(3 5% TA52 3K 1/4W(3 5% TAOHM 1/2 W (7.0) 5% TA52 2.20K 1/4W(3 5% TA52 3K 1/4W(3 5% TAOHM 2 W 5% TA62 4.70 1/4W(3 5% TA52 22K OHM 1/2 W (7.0) 5% TA52 TIN 50MM TAPING 130K 1/6W 1% TA52 10K OHM 1/4 W (3.4) 2% TA52 3K 1/4W(3 5% TA52 3K 1/4W(3 5% TA52 3K 1/4W(3 5% TA52 TIN 50MM TAPING 300 OHM 1/2 W (7.0) 5% TA52 1.50K 1/4W(3 5% TA52 510K OHM 1/2 W (7.0) 5% TA52 1K 1/6W 1% TA52 1.50K 1/4W(3 5% TA52 18K OHM 1/4 W (3.4) 2% TA52 33K OHM 1/2 W (7.0) 5% TA52 2K 1/4W(3 5% TAOHM 1/4 W(3.4) 2% TA52 3.3K OHM 1/2 W(7.0) 5.00% TA TIN 50MM TAPING 100 1/4W(3 5% TA52 47K 1/4W(3 5% TA52 - Only(S/W 710S) 1.50K 1/4W(3 5% TA52 2K 1/4W(3 5% TA52 15K 1/4W(3 5% TA52 18K 1/4W(3 5% TA52 15K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52 2K 1/4W(3 5% TA52 47K 1/4W(3 5% TA52 75K 1/4W(3 5% TAOHM 2 W 5% SF 43K 1/4W(3 5% TA52 10K 1/4W(3 5% TA52 3.30K 1/6W 1% TA52 62KOHM 1/6 W 1% TA52 82K 1/6W 1% TA52 10K 1/4W(3 5% TA52 470K OHM 1/2 W (7.0) 5% TA1/4W(3 5% TAOHM 1/6 W 1.00% TA52 39K OHM 2 W 5% SF

- 28 -

*S *AL LOC. NO. R906 R907 R908 R910 R911 R912 R913 R915 R916 R918 R923 R924 R925 R926 R927 R928 R929 R941 R944 R945 R951 R952 R953 R954 R955 R956 R957 R960 R962
PART NO. 0RD6200Q609 0RD3902Q609 971-0054 0RX4702J609 0RD0202Q609 0RN1802F409 0RN2701F409 0RD0622Q609 0RD1002Q609 0RD1001Q609 0RD1003Q609 0RN0390H609 0RN0390H609 0RD4301Q609 0RD2002Q609 0RD1800Q609 0RD0332Q609 0RN0220H609 0RD4700A609 0RD4701Q609 971-0054 0RD1202A609 0RD1001A609 0RD4701Q609 0RD4701Q609 0RD6802A609 0RD0472A609 0RD6200A609 0RD0332Q609
DATE: 2003. 11. 14. DESCRIPTION / SPECIFICATION 620 1/4W(3 5% TA52 39K 1/4W(3 5% TA52 TIN 50MM TAPING 47K OHM 1 W 5% TA1/4W(3 5% TA52 18K 1/6W 1% TA52 2.7K OHM 1/6 W 1.00% TAOHM 1/4 W(3.4) 5.00% TA52 10K 1/4W(3 5% TA52 1K 1/4W(3 5% TA52 100K 1/4W(3 5% TA52 0.39 1/2W 5 TA52 0.39 1/2W 5 TA52 4.30K 1/4W(3 5% TA52 20K 1/4W(3 5% TA1/4W(3 5% TA1/4W(3 5% TA52 0.22 1/2W 5% TAOHM 1/2 W (7.0) 5% TA52 4.70K 1/4W(3 5% TA52 TIN 50MM TAPING 12K OHM 1/2 W(7.0) 5.00% TA5 1K OHM 1/2 W (7.0) 5% TA52 4.70K 1/4W(3 5% TA52 4.70K 1/4W(3 5% TA52 68K OHM 1/2 W (7.0) 5% TAOHM 1/2 W (7.0) 5% TAOHM 1/2 W(7.0) 5.00% TA1/4W(3 5% TA52

HFLB XRAY BOP BSENS BIN BDRV PGND HDRV XSEL Vcc
FOCUS HSMOD HPLL2 HCAP HREF HBUF HPLL1 SGND VCAP VREF VAGC VSMOD ASCOR SDA SCL HUNLOCK (video) 3.3 (1) See calculation of f range. H (2) See Figs 22 and 23. 100nF 8.2 nF H/C-sync (TTL level) 15 H/C-SYNC INPUT AND POLARITY CORRECTION PLL1 AND H-POSITION V+ 9.2 to 16V SDA SCL 25 SUPPLY AND REFERENCE I 2C-BUS RECEIVER HUNLOCK 17 HUNLOCK OUTPUT V-sync (TTL level) clamping blanking V-SYNC INPUT AND POLARITY CORRECTION VIDEO CLAMPING AND V-BLANK V-SYNC INTEGRATOR
VERTICAL OSCILLATOR AND AGC
EHT COMPENSATION H-SIZE AND V-SIZE
V-POSITION V-SIZE, VOVSCN TDA4841PS PROTECTION AND SOFT START OUTPUT ASYMMETRIC EW-CORRECTION FOCUS HORIZONTAL AND VERTICAL 20 or

I 2C-BUS REGISTERS

6 COINCIDENCE DETECTOR FREQUENCY DETECTOR X-RAY PROTECTION B+ CONTROL 5 APPLICATION (2) B+ CONTROL

EWDRV 11 VOUT2 VOUT13

VSYNC 14 HSYBC 15 CLBL 16
HORIZONTAL OSCILLATOR 28 R HBUF (1) R HREF 1% nF 2%
PLL2, PARALLELOGRAM, PIN UNBALANCE AND SOFT START 2 9

H-OUTPUT STAGE

8 HDRV

12 nF HFLB X-RAY XSEL

KA3842B
Current-Mode PWM Controller

- 31 -

SCHEMATIC DIAGRAM
NOTICE Since this is a basic schematic diagram. The value of components and some partial connection are sucject to be changed for improvement without notice.

- 32 -

- 33 -

PRINTED CIRCUIT BOARD

1. MAIN BOARD (Component Side)
2. MAIN BOARD (Solder Side)

- 34 -

- 35 -

P/NO : 3828TSL099G

Nov. 2003 Printed in Korea