Function

Video Menu Options Adjusting Video.. APC (Auto Picture Control).. Auto Color Temperature Control. Gamma Function.. Brilliant Color TM Function. White peaking Function.. Black Level Function.. Smart Iris Function.. 29 29
Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

ENGLISH

Safety Instructions
Please take note of the safety instructions to prevent any potential accident or misuse of the projector. Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause light injuries or damage to the projector. After reading this manual, keep it in the place that the user always can contact easily.

Indoor Installation

Stand the projector when you install.
If not, the power turns off.

WARNING

Do not place the Projector in direct sunlight or near heat sources such as radiators, fires and stove etc.
This may cause a fire hazard !
Do not place inflammable materials beside the projector
Do not allow children to hang on the installed projector.
It may cause the projector to fall, causing injury or death.
Disconnect the power and remove all connections before moving.
Do not place the projector close to sources of steam or oil such as a humidifier.
This may create a fire hazard or an electric shock hazard !
Do not place the projector where it might be exposed to excessive dust.
Only use the projector on a level and stable place.
It may become unstable and affect operation.
Ensure good ventilation around the projector. The distance between the projector and the ceiling or bottom should be more than 20cm/8 inches. An excessive increase in its internal temperature may cause a fire hazard!
Do not block the vents of the projector or restrict air-flow in any way.
This would cause the internal temperature to increase and could cause a fire hazard!
Do not place the projector directly on a carpet, rug or place where ventilation is restricted.

This would cause its internal temperature to increase and might create a fire hazard !
The air flow from the projector inflow from the bottom left part and outflows to the top right. Therefore when installing a ventilator close, be careful not to change the direction of the air flow.
When installing the ventilator at the bottom part of the projector, it can cause a fire by raising the internal temperature.

Outdoor Installation

Do not use the projector in a damp place such as a bathroom where it is likely to get wet.
This may cause a fire or an electric shock hazard !
Earth wire should be connected.
If the earth wire is not connected, there is a possible danger of electric shock caused by the current leakage. If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician. Do not connect ground to telephone wires, lightning rods or gas pipe.
The mains plug should be inserted fully into the power outlet to avoid a fire hazard !
Do not place heavy objects on the power cord
Do not plug too many devices into one outlet.
It may result in overheating of the outlet and causes a fire hazard !
Never touch the power plug with a wet hand
This may cause an electric shock hazard !
Hold the plug firmly when unplugging. If you pull the cord the cord may be damaged.
Prevent dust collecting on the power plug pins or outlet.
Do not plug in when the power cord or the plug is damaged or the connecting part of the power outlet is loose.
Ensure the power cord does not come into contact with sharp or hot objects such as a heater.
Place the projector where people will not trip or tread on the power lead.
Do not turn the projector On/Off by plugging-in or unplugging the power plug to the wall outlet. (Do not use a switched power outlet to turn the unit on and off.)
It may cause mechanical failure or could give an electric shock.
Do not place anything containing liquid on top of the projector such as flowerpot, cup, cosmetics or candle.
In case of impact shock or damage to the projector, switch it off and unplug it from the outlet. Contact a service center.
Do not allow any objects to fall into the projector.

If water is spilt into the projector, unplug it from the outlet immediately and consult a Service Agent.
Dispose of used batteries carefully and safely.
In the case of a battery being swallowed by a child please consult a doctor immediately.
In the event that an image does not appear on the screen, please switch the unit off and unplug it from power outlet. Contact a Service Agent.
Do not remove any covers (except lens cover). High risk of Electric Shock!
Dont look directly onto the lens when the projector is in use. Eye damage may occur!
Do not touch metal parts during or soon after operation since the vents and lamp cover will remain very hot!
CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; that is,a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits.Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets,loose or damaged wall outlets, extension cords, frayed power cords,or damaged or cracked wire insulation are dangerous.Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance,and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized services. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 5
Never touch the wall outlet when there is leakage of gas, open the windows and ventilate.
It can cause a fire or a burn by a spark.
Do not drop the projector or allow impact shock.
This may cause mechanical failure or personal injury !
Do not place heavy objects on top of projector.
This may cause mechanical failure or personal injury!
Take care not to cause impact to the lens particularly when moving the projector. Do not touch the lens of the projector. It is delicate and easily damaged.
Do not use any sharp tools on the projector as this will damage the casing.

Cleaning

Do not use water while cleaning the projector
This may cause damage to the projector or an electric shock hazard.
In the unlikely event of smoke or a strange smell from the projector, switch it off, unplug it from the wall outlet and contact your dealer or a service center.
Use an air spray or soft cloth that is moist with a neutral detergent and water for removing dust or stains on the projection lens.
Contact a Service Center once a year to clean the internal parts of the projector.
Accumulated dust can cause mechanical failure.
When cleaning the plastic parts such as projector case, unplug the power and wipe it with a soft cloth. Do not use cleanser, spray water or wipe with a wet cloth. Especially, never use cleanser (glass cleaner), automobile or industrial shiner, abrasive or wax, benzene, alcohol etc., which can damage the product.
It can cause fire, electric shock or product damage (deformation, corrosion and damage).

Others

Do not attempt to service the projector yourself. Contact your dealer or a service center.
This may cause damage to the projector and could give an electric Shock as well as invalidating the warranty !
Be sure to unplug if the projector is not to be used for a long period.
Accumulated dust may cause a fire hazard!
Refer to 38~39 page to replace the lamp. Do not mix new batteries with old batteries.
This may cause the batteries to overheat and leak.
Only use the specified type of battery.
This could cause damage to the remote control.
Watch the projector screen keeping about 5 to 7 times the diagonal distance of the screen.
Watching the screen too close can reduce your eyesight.

Main Body

* The projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction.

FOCUS Ring

Lens shift
Remote control sensor Indicators
RGB Input (PC/DTV) Video Input S-Video Input COMPONENT Input

AC IN HDMI Input

Control Panel
MENU Button SOURCE Button A OK Button
/ KEY STONE Button / SMART IRIS Button
/ ZOOM + Button / ZOOM - Button Button

Remote Control

POWER Button MENU Button

MENU SOURCE

SOURCE Button

/ G Button

Button
AUTO Button (Refer to p.34)

AUTO OK

OK Button
ARC Button (Refer to p.30) STILL Button (Refer to p.33)
BLANK Button (Refer to p.32)

BLANK ARC STILL

KEYSTONE Button (Refer to p.32)

Projection Screen

Desktop Stand
SCART to RCA jack (option)

S-Video Cable

HDMI Cable

Component Cable

Cable Cover
Installation and Composition
Installation Instructions
* Dont place the projector in the following conditions. It may cause malfunction or product damage. Provide proper ventilation for this projector.
The projector is equipped with ventilation holes(intake) on
Never insert materials as paper into the lower of the
the bottom and ventilation holes(exhaust) on the front. do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.

projector.

Ensure good ventilation around the projector.
For proper ventilation, allow a clearance of 1cm on
The distance between the projector and the ceiling or bottom should be more than 20cm/8 inches.
each side and from the wall.
Place this projector in adequate temperature and humidity conditions.
Install this projector only in a location where adequate temperature and humidity is available. (refer p.43)
Dont place the projector where it can be covered with dust.
This may cause overheating of the projector.
The projector is manufactured using high-precision technology. You may, however, see tiny black points and/or bright points (red, blue, or green) that continuously appear on the projector Screen. This is a normal result of the manufacturing process and does not indicate a malfunction.
To display DTV programs, it is necessary to connect a DTV receiver (Set-top Box) and connect it to the projector.
If there is no input signal, the Menu will not be displayed on screen.
Basic Operation of the Projector
1.Place the projector on a wall. 2.Place the projector the correct distance from the screen. The distance between the projector and the screen determines the actual size of the image. 3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 32.) 4.Connect the cables of the projector to a wall power socket and other connected sources.

projection distance based on the picture format

Projection distance (D)

Projection distance (D) 16:9 picture format screen screen size (inches) 300 screen size (mm) 7620 screen horizontal size (mm) 6641 screen vertical size (mm) 3736 mm / inches Projection distance
The shortest distance (mm) The longest distance (mm)
* The longest/shortest distance show status when adjusted by the zoom function. 13
Installing the projector to the wall
Safety instructions on installing the wall
Please take note of the safety instructions to prevent any potential accident or misuse of the projector.
Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause light injuries or damage to the projector. After reading this manual, keep it in the place that the user always can contact easily.
Do not install this product on the place where it cannot be supported.
It may cause the product to fall and could cause injuries.
Do not hang on or impact this product.
Follow the instructions when installing this product.
Otherwise it may cause serious injuries or damage of the product.
Do not install this product by yourself. Get some help from others.
Before installing, check whether the material of wall satisfies the specifications and make sure to use enclosed anchors supplied with the product.
Otherwise it may cause safety problem.
When drilling use drill and drill bit specified by the manufacturer. And the depth of the hole should satisfy the specifications.
Do not place a heat source (radiator or heater) or a humidifier under the installed product.
It may cause a fire or could give an electric shock.
Do not install this product near a sprinkler, a sensor, a high voltage electric line, any power source or the place where impact or vibration can affect.
Unplug the product before installing.
Otherwise it may cause a fire or could give an electric shock.
Do not install this product barehanded.

It may cause injuries.

Installing and Composition Accessories for wall mounting bracket
Bolts for wall mounting bracket

Wall anchor bolt sleeves

Bolts for fixing the bracket

Fixing fixers

Bolts for using the wood
Installing Wall mounting bracket

Detach the products

- Detach bolt from wall mounting bracket. - Detach product fixing bracket from Wall mounting bracket.

Adjust the focus by using FOCUS ring of the set.
Adjust the screen size by using ZOOM+/- button of the remote control or the control panel.
If you want to adjust the screen image to upside/downside, adjust the lens shift as shown below.
Adjust the Lens shift to upside/downside the set the wanted position of screen.
Connecting to a Desktop PC
* You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output. * Refer to page 36 for the supported monitor displays of the projector.

< How to connect >

Connect computer cable to RGB IN (PC/DTV) of the projector.
* You can get better picture quality when connecting HDMI source to the projector.

RGB IN (PC/DTV)

S-VIDEO COMPONENT IN

Y HDMI IN

Connecting to a Notebook PC
* If you set your computer to output the signal to both the display of your computer and the external projector, the picture of the external projector may not appear properly. In such cases, set the output mode of your computer to output the signal only to the external projector. For details, refer to the operating instructions supplied with your computer.
RGB IN (PC/DTV) VIDEO S-VIDEO COMPONENT IN
Connecting to a Video Source
* You can connect a VTR, a camcorder or any other compatible video image source to the projector.
< How to connect 1 >
a. Connect the Video input jacks of the projector to the output jacks of the A/V source with Video cable.
< How to connect 2 >
b. Connect the S-Video input jack of the projector to the S-Video output jack of an A/V source with an S-Video cable.
* You can get better picture quality when connecting S-Video source to the projector.

<VCR>

S VIDEO (R) AUDIO (L) VIDEO

OUT IN

Connecting to a DVD
* The output jacks (Y, PB, PR) of the DVD might be labeled as Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according to the equipment.
a. Connect the DVD Component cable to Component Pr, Pb, Y of the projector.

* When connecting the component cable, match the jack colors with the component cable.(Y=green, PB=blue, PR=red)
b. You can select HDMI Mode if DVD player has HDMI output.
Signal 480i 480p 720p 1080i 576i 576p Component O O O O O O RGB/DTV X O O O X O HDMI/DVI X O O O X O
HDMI to DVI cable Component cable

<DVD>

Y HDMI IN PB PR

(R) AUDIO (L)

DVI OUTPUT

HDMI OUTPUT

HDMI cable
Connecting to a D-TV Set-Top Box
* To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector. * Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and D-TV Set-Top Box.
< How to connect an RGB source >
a. Connect RGB cable to RGB IN (PC/DTV) of the projector. b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.

* HDMI supports HDCP.

<D-TV Set-Top Box>
< How to connect a HDMI source >
a. Connect the D-TV Set-Top Box HDMI cable to HDMI of the projector. b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.

DTV OUTPUT

RGB cable HDMI to DVI cable HDMI cable
< How to connect a Component source >
a. Connect the D-TV Set-Top Box Component cable to Component PR, PB, Y of the projector.
b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode.

Component cable

* In this manual, the OSD(On Screen Display) may be different from your Projectors because it is just an example to help with the Projector operation. * If there is no input signal present, the Menu will not be displayed. * This operating guide explains operation of RGB(PC) mode mainly.

Video Menu Options

Adjusting Video

< RGB mode >

1. Press the MENU button and then use F, G button to select the 2. Press the D , E button to select a video item you want to adjust. 3. Press the F, G button to adjust the screen condition as you want.
Contrast Brightness Color R Color G Color B Reset MENU Exit 50
Each adjustment of menu options will not affect other inputs. As required, re-adjust menu options for the following input source : Video/S-Video/Component (480i(576i)), Component (480p(576p), 720p, 1080i) To restore the original image condition after changing it, press A OK button after selecting [Reset] item. When receiving an NTSC signal, the picture item Tint is displayed and can be adjusted.(60Hz only) To exit the menu display, repeatedly, press the MENU button.

< Video mode >

APC Contrast Brightness Color Sharpness Tint MENU Exit

< HDMI mode >

Contrast Brightness Reset

MENU Exit

APC (Auto Picture Control)
* Use APC to set the projector for the best picture appearance. * This function will not work in RGB mode.
1. Press the MENU button and then use F, G button to select the 2. Press the
D , E button to select APC
APC Contrast Brightness Color Sharpness Tint MENU Prev.
3. Press the F, G button to adjust the screen condition as you want.
Each press of the D, E button changes the screen as shown below. Clear Soft User
To exit the menu display, repeatedly, press the MENU button. 27
Auto Color Temperature Control
- To initialize values (reset to default settings), select the Normal option.
D , E button to select ACC
ACC Gamma Brilliant Color TM White peaking Smart Iris MENU Exit

Normal Normal On

G G G G
3. Press the F, G button to make desired adjustments.

Each press of the Cool

button changes the screen as shown below. Normal Warm
To exit the menu display, repeatedly, press the MENU button.

Gamma Function

1. Press the MENU button and then use F, G button to select the 2. Press the 3. Press the
D , E button to select Gamma F, G
button to adjust the screen condition as required.

Each press of the D,

Normal
button changes the screen as shown below.

Film Sports

Brilliant Color
1. Press the MENU button and then use F, G button to select the 2. Press the D , E button to select Brilliant Color TM item. 3. Press the F, G button to select On or Off.
* What does Brilliant Color do? This function either increases or decreases entire luminosity by enriching the impression of a halftone color.

White peaking Function

D , E button to select White peaking
Adjust to higher setting to achieve brighter picture. Adjust to lower setting for darker picture. To exit the menu display, repeatedly, press the MENU button. You can adjust White peaking only when Brilliant Color TM is On.

Adjust

Black Level Function

Using Still Function

1. Press the STILL button.
* You can freeze the input image.

<Moving Image>

<Still Image>
2. To exit STILL, press any button.
* The STILL function will release automatically after approximately 10 minutes.

Screen Menu Options

Auto Configure Function
* This function assures you of getting the best video quality by automatically adjusting the horizontal size and synchronization of the image. * Auto Tracking function works in RGB PC input only.
1. Press the AUTO button.
Image positioning and synchronization are automatically adjusted.

Auto Configure

2. You want adjust more by various PC input modes, adjust Phase, Clock, Horizontal and Vertical in menu. In certain circumstances, you cant get the best picture quality by only using auto-correction.
You can also use this function by using the MENU button. (Only in RGB mode) For best results, perform this function while displaying a still image.

Using Phase Function

1. Press the MENU button and then use menu. 2. Press the 3. Press the
Auto configure Phase Clock Horizontal Vertical MENU Store 0 0

D,E F, G

button to select Phase item. button to make desired adjustments.
Phase adjustment range is 0 ~31. To exit the menu display, repeatedly, press the MENU button. The variable range can be different depends on input resolutions.

Using Clock Function

button to select Clock item. button to make desired adjustments.
Clock adjustment range is -20 ~+20. To exit the menu display, repeatedly, press the MENU button. The variable range can be different depends on input resolutions.
Using Horizontal Function
button to select Horizontal item. button to make desired adjustments.
Horizontal adjustment range is -25 ~+25. To exit the menu display, repeatedly, press the MENU button. The variable range can be different depends on input resolutions.

Using Vertical Function

button to select Vertical item. button to make desired adjustments.
Vertical adjustment range is -25 ~+25. To exit the menu display, repeatedly, press the MENU button. The variable range can be different depends on input resolutions.
Supported Monitor Display
* The following table lists the display formats supported by the projector.

Sources

EGA PC98 DOS

Format

640X350 640X350 640X400 720X400 720X400 640X480 640X480 640X480 640X480 800X600 800X600 800X600 800X600 800X600 1024X768 1024X768 1024X768 1024X768 1152X864 1152X864 1152X864 1280X768 1280X960 1280X1024 1280X1024

Vertical Freq.(Hz)

70.09Hz 85.08Hz 85.08Hz 70.08Hz 85.03Hz 59.94Hz 72.80Hz 75.00Hz 85.00Hz 56.25Hz 60.31Hz 72.18Hz 75.00Hz 85.06Hz 60.00Hz 70.06Hz 75.02Hz 84.99Hz 60.05Hz 70.01Hz 75.00Hz 60.00Hz 60.00Hz 60.02Hz 75.025Hz

Horizontal Freq. (kHz)

31.468kHz 37.861kHz 37.861kHz 31.469kHz 37.927kHz 31.469kHz 37.861kHz 37.500kHz 43.269kHz 35.156kHz 37.879kHz 48.077kHz 46.875kHz 53.674kHz 48.363kHz 56.476kHz 60.023kHz 68.677kHz 54.348kHz 63.995kHz 67.500kHz 47.693kHz 60.000kHz 63.981kHz 79.976kHz

* * * * *

In case of the use of HDMI To HDMI cable, PC shall not be supported. If the projector does not support the input signal, Out of range message appears on the screen. The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor) The Synchronization input form for horizontal and vertical frequencies are Separate. According to PC, the optimum vertical frequency may not be displayed up to the optimum frequency of set in Registration information (Display registration information). (ex, The optimum vertical frequency may be displayed up to 85Hz or under in the resolution of 640X480 or 800X600.)
< DVD/DTV Input > Signal
480i NTSC(60Hz) 480p 720p 1080i 576i PAL(50Hz) 576p 720p 1080i

Component-*1 RGB(DTV)-*2

O O O O O O O O X O O O X O O O

HDMI(DTV)-*3

X O O O X O O O
* Cable type 1- Component Cable 2- Computer Cable 3- HDMI Cable * We recommend using 720p resolution.

Maintenance

* The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear on the screen. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector, always turn the power off and unplug the projector first.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface of it. Wipe the lens surface gently with an air spray or a soft, dry lint-free cloth. To remove dirt or stains on the lens, moisten a soft cloth with water and a neutral detergent and wipe the lens surface gently.
Cleaning the Projector Case
To clean the projector case, first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing. Do not use alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.

Replacing the Lamp

Last of Lamp unit replacement
The projector lamp usually lasts for about 2000 hours. You can see the used lamp time in the Selecting Function section. You must replace the lamp when:
<Front panel of the Projector>
The projected image gets darker or starts to be deteriorated. The lamp indicator is red. The message Replace the lamp appears on the screen when turning the projector lamp on.

Lamp indicators

Be careful when replacing lamp
- Press the POWER button on the control panel or remote control to cut off the power. - If the operation indicator LED is orange and blinking, do not disconnect the mains supply until the operation indicator LED is lit up constantly (orange). - Allow the lamp to cool for 1 hour before replacing it. - Replace only with the same type lamp from a LG Electronics Service Center using and other lamp may cause damage to the Projector and lamp. - Pull out the lamp only when replacing the lamp. - Keep the lamp unit out of reach of children or and heat sources such as radiators, stoves. - To reduce the risk of fire, lamp shall not be exposed to liquids or foreign material. - Do not place the lamp near any heat source. - Make sure the new lamp is securely tightened with screws. If not, the image may be dark or there could be a risk of fire. - Never touch the lamp unit glass or otherwise image quality may be worse or lamp life may be reduced.
To obtain a replacement Lamp unit
Lamp model number is on page 43. Check the lamp model and then purchase it at LG Electronics Service Center. Using other lamp may cause damage to the projector.

Lamp unit disposal

Dispose of the used lamp by returning it to the LG electronic service center.
Turn off the projector and unplug the power cable. Carefully place the lens side down on a cushioned surface that will protect the lens from damage. (Allow the lamp to cool for 1 hour before replacing it.)
Unscrew the fixing bolts of the lamp cover using a driver or a similar object.

Lamp case bolt

After lifting the lamp cover off, remove the two retaining screws on the lamp case with a screwdriver or similar objects.
Lift up the fixed wire knob on the lamp.
Pull out the handle slowly and remove the lamp case.
Insert the new lamp gently into the correct position. Make sure it is inserted correctly.
Tighten the screws you removed in step 3.
(Make sure it is fixed hardly.)
Close the lamp cover and fix it with the bolts from 2.

(If the lamp cover is open, the lamp indicator flashes green and the projector is not turned on.)
Using and other lamp may cause damage to the projector or lamp. Make sure the lamp cover is securely fastened. If the lamp cover is open, and the projector is not turned on. In this case, contact your service center after checking the lamp to fix well.
Regarding the projector lamp control
Dont turn off the projector at least in 5 minutes after activating it. - The frequent On/Off changes may cause the lamp function to deteriorate. Dont pull out the power cord while activating the projector and the cooling fan. - It may cause the lamp life-span to shorten and get damaged. The life-span of projector may considerably depend on the use environment and treatment conditions. The projector uses the high pressure mercury lamp so that the serious caution is essential. The shock or abuse while using may cause lamp to blow off with explosion. When you continue to use the projector after an interval of lamp replacement, the lamp may be blown off with explosion. The following treatment should be done, in case of lamp blow-off. - Pull off the power cord immediately. - Let some fresh air in immediately (Ventilation). - Check the product condition at the nearer service center and replace it with new lamp, if necessary. - Dont try to disassemble the product without the authorized technician.

Specifications

MODEL resolution horizontal / vertical ratio DLP panel size screen size remote control distance zoom ratio Video compatibility Power height(mm/inches) breadth(mm/inches) length(mm/inches)

AN215-JD

1280(Horizontal) x 720(Vertical)pixel 16:9(horizontal:vertical) 0.62 inches 1.53~11.65m(40~300 inches) 12m 1:1.4 NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N AC 100 - 240V~50/60Hz, 3A-1A, 260W 285/11.3 470.0/18.5 107.8/4.3
Operating Condition temperature
In operation : 32~104F(0C~40C) In storage and transit : -4~140F(-20C~60C)
Projector Lamp lamp model

AJ-LAN2

humidity
In operation : 0~ 80% relative humidity by dry hygrometer Not in operation : 0 ~ 90% relative humidity by dry hygrometer

lamp power consumption

LAMP Replacement WARNING : Lamp is no user replaceable part. Do not touch and open the lamp replace cover of bottom enclosure. It could cause injury and electric shock due to high temperature and voltage. Only service personnel can replace lamp after minimum 3 min. from disconnect mains plug to avoid injury cause by high temperature of lamp. * Applicable Lamp: Manufactured by USHIO Inc., type NSH200LG
Du bedes lse denne brugervejledning grundigt igennem, frend du betjener enheden. Gem brugervejledningen til fremtidig brug. Skriv model- og fabrikationsnummeret p enheden ned herunder. Opgiv oplysningerne p mrkatet i bunden af enheden til din forhandler, hvis du fr brug for service. Modelnummer Fabrikationsnummer : :