Safety Information

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this user guide. ] Never use an unapproved battery since this could damage the phone and/or battery and could cause the battery to explode. ] Never place your phone in a microwave oven as it will cause the battery to explode. ] Do not dispose of your battery by fire or with hazardous or flammable materials.
] Make sure that no sharp-edged items come into contact with the battery. There is a risk of this causing a fire. ] Store the battery in a place out of reach of children. ] Be careful that children do not swallow any parts such as rubber plugs (earphone, connection parts of the phone, etc.). This could cause asphyxiation or suffocation. ] Unplug the power cord and charger during lightning storms to avoid electric shock or fire. ] When riding in a car, do not leave your phone or set up the hands-free kit near to the air bag. If wireless equipment is improperly installed and the air bag is activated, you may be seriously injured. ] Do not use a hand-held phone while driving. ] Do not use the phone in areas where its use is prohibited. (For example: aircraft). ] Do not expose the battery charger or adapter to direct sunlight or use it in places with high humidity, such as a bathroom. ] Never store your phone in temperatures less than4F or greater than 122F.
] Do not use harsh chemicals(such as alcohol, benzene, thinners, etc.) or detergents to clean your phone. There is a risk of this causing a fire. ] Do not drop, strike, or shake your phone severely. Such actions may harm the internal circuit boards of the phone. ] Do not use your phone in high explosive areas as the phone may generate sparks. ] Do not damage the power cord by bending, twisting, pulling, or heating. Do not use the plug if it is loose as it may cause a fire or electric shock. ] Do not place any heavy items on the power cord. Do not allow the power cord to be crimped as it may cause fire or electric shock. ] Do not handle the phone with wet hands while it is being charged. It may cause an electric shock or seriously damage your phone. ] Do not disassemble the phone. ] Do not place or answer calls while charging the phone as it may short-circuit the phone and/or cause electric shock or fire.

] Only use the batteries, antennas, and chargers provided by LG. The warranty will not be applied to products provided by other suppliers. ] Only authorized personnel should service the phone and its accessories. Faulty installation or service may result in accidents and consequently invalidate the warranty. ] Do not hold or let the antenna come in contact with your body during a call. ] An emergency call can be made only within a service area. For an emergency call, make sure that you are within a service area and that the phone is turned on. ] Use accessories, such as earphones and headsets, with caution. Ensure that cables are tucked away safely and do not touch the antenna unnecessarily.
electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards.

CAUTION

Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with skin, a minor burn may result. Contact your local dealer for a replacement antenna.

Body-worn Operation

This device was tested for typical body-worn operations with the back of the phone kept 0.6 inches (1.5cm) between the users body and the back of the phone. To comply with FCC RF exposure requirements, a minimum separation distance of 0.6 inches(1.5cm) must be maintained between the user s body and the back of the phone. Third-party belt-clips, holsters, and similar accessories containing metallic components
FCC RF Exposure Information
WARNING! Read this information before operating the phone. In August 1996, the Federal Communications (FCC) of he United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF)
should not be used. Body-worn accessories that cannot maintain 0.6 inches(1.5cm) separation distance between the user's body and the back of the phone, and have not been tested for typical body-worn operations may not comply with FCC RF exposure limits and should be avoided.

Cautions for Battery

] Do not disassemble. ] Do not short-circuit. ] Do not expose to high temperature: 60C (140F).] ] Do not incinerate.
Vehicle Mounted External Antenna (optional, if available)
A minimum separation distance of 8 inches (20cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCC website at www.fcc.gov

Battery Disposal

] Please dispose of your battery properly or bring to your local wireless carrier for recycling. ] Do not dispose in fire or with hazardous or flammable materials.
Adapter (Charger) Cautions
] Using the wrong battery charger could damage your phone and void your warranty. ] The adapter or battery charger is intended for indoor use only. Do not expose the adapter or battery charger to direct sunlight or use it in places with high humidity, such as the bathroom.
FCC Part 15 Class B Compliance
This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device and its accessories may not cause harmful interference, and (2) this device and its accessories must accept any interference received, including interference that may cause undesired operation.

Avoiding hearing damage

Permanent hearing loss may occur if you use your phone and/or headset at a high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected. Hearing experts suggest that to protect your hearing: ] Limit the amount of time you use your phone and/or headset at high volume. ] Avoid turning up the volume to block out noisy surroundings. ] Turn the volume down if you can't hear people speaking near you. For information about how to set a maximum volume limit on your phone, see the features guide for your phone.

Using your phone safely

Use of your phone while operating a vehicle is not recommended and is illegal in some areas. Be careful and attentive while driving. Stop using your phone if you find it disruptive or distracting while operating any type of vehicle or performing any other activity that requires your full attention.

External Display Your phone has an external display on the cover. It indicates when you have an incoming call or a message. It also alerts you at the specified time when you set an alarm by turning on its backlight and showing corresponding icon on it.

Display Information

Icon area

Text and graphic area

Soft key indications

First line Middle lines

Description
Displays various icons. Dispaly messages, instructions and any information that you enter, such as number to be dialed. Shows the functions currently assigned to the two soft keys.

Last line

On-Screen Icons
The table below describes various display indicators or icons that appear on the phones display screen. Icon Description
Indicates the strength of the 3G network signal. Indicates the strength of the network signal. Indicates that the EDGE service is available. Connection to the EDGE service allows you to transfer data at a speed of 200Kb/s(depending on network availability). Check with your operator for network coverage and service availability. Indicates that GPRS service is available. Indicates that Flight mode has been activated. Indicates the status of the battery charge. Indicates that a call is in progress. Indicates that the alarm has been set and is on. Indicates the Schedule function. Indicates the receipt of a message. Indicates the receipt of a Voicemail.
Indicates that Ring has been set for alert. Indicates that Ring and vibration has been set for alert. Indicates that Silent has been set for alert. Indicates that Vibration has been set for alert. Indicates that the speakerphone has been activated. Indicates that the Bluetooth function has been activated. Indicates that the data is being transmitted using a Bluetooth connection. Indicates that the connection to a headset with Bluetooth has been activated. Indicates that the Multitasking function has been activated. Indicates that the TTY has been set and is on. Indicates that the status of PTT is Available. Indicates that the status of PTT is Unavailable. Indicates that the status of PTT is Do Not Disturb. Indicates a PTT Message is waiting in the PTT Menu. Indicates that the phone is accessing the WAP. Indicates that Hearing Aid function has been activated.
The Bluetooth word mark and logos are owned by the * license. Other trademarks and trade names are those ofBluetooth SIG, Inc. and any use of such marks by LG Electronics is under their respective owners. 16

Your phone offers a set of functions that allow you to customize the phone. These functions are arranged in menus and sub-menus, accessed via the two soft keys marked the left soft key and the right soft key. Each menu and sub-menu allows you to view and alter the settings of a particular function. Soft key functions vary depending on the mode of the phone. The label on the bottom of the display screen immediately above the soft keys indicates the current function.
Press the left soft key to access the available Menu.
Press the right soft key to access the available Options.
A short press will launch the WAP browser. A short press allows you to select and confirm menu options.

In-Call Menu

Your phone provides a number of control functions that you can use during a call. To access these functions during a call, press the right soft key [Options].
Answering an Incoming Call
To answer an incoming call when the handset is ringing, simply press the [SEND] key. The handset is also able to warn you of an incoming call while you are already on a call. A tone sounds in the earpiece, and the display will show that a second call is waiting. This feature, known as Call Waiting, is only available if your network supports it. If Call Waiting is on, you can put the first call on hold and answer the second call, by pressing the [SEND] key.

During a Call

The menu displayed on the handset screen during a call is different from the default main menu displayed when in idle screen, and the options are described below.

Making a Second Call

You can select a number you wish to dial from the Address Book to make a second call. Press the right soft key then select Contact List.
Rejecting an Incoming Call
You can reject an incoming call without answering by simply pressing the [END] key. During a call, you can reject an incoming call by pressing the [END] key.
Swapping Between Two Calls
To switch between two calls, press the right soft key or the [SEND] key, and then select Swap.

Muting the Microphone

You can mute the microphone during a call by pressing the left soft key [Mute]. The handset can be unmuted by pressing the left soft key [Unmute]. When the handset is muted, the caller cannot hear you, but you can still hear the caller.

Conference Calls

The conference service provides you with the ability to have a simultaneous conversation with more than one caller. The conference call feature can be used only if your network service provider supports this feature. A conference call can only be set up when you have one call active and one call on hold, meaning both calls must have been answered. Once a conference call is set up, calls may be added, disconnected or separated (that is, removed from the conference call but still connected to you) by the person who set up the conference call. These options are all available from the In-Call menu. The maximum number of callers in a conference call is five. Once started, you are in control of the conference call, and only you can add calls to the conference call.

Using the Speakerphone

You can use the speakerphone during a call by pressing the or [speakerphone] key located on the top of the phone. The loudspeaker is automatically deactivated when you end the call. n Warning
Due to higher volume levels, dont place the phone near your ear while the speakerphone is enabled.
You can make a second call while currently on a call simply by entering the second number and pressing the [SEND] key. When the second call is connected, the first call is automatically placed on hold. You can swap between calls, by pressing the [SEND] key.
Adding Calls to the Conference Call
To add a call to an existing conference call, press the right soft key, and then select the Join Calls sub menu from the Conference Call option.
Private Call in a Conference Call
To have a private call with one caller from a conference call, press the right soft key and select the Private Call from the Conference Call option. When the numbers of the callers are displayed, select the one you wish to speak in private.
Setting Up a Conference Call
To set up a conference call, place one call on hold, conference in the second active call by pressing the right soft key and select the Join Calls sub menu option from the Conference Call menu.

Ending a Conference Call

Currently active conference call can be disconnected by pressing the [END] key.
Activate the Conference Call on Hold
To activate a conference call on hold, press the [SEND] key.

Menu Tree

The following illustration shows the available menu structure and indicates the: ] Number assigned to each menu option. ] Page where you can find the feature description. 1. Cingular Video (see page 34) 2. Messaging (see page 35)
2.1 New Message 2.2 Inbox 2.3 IM 2.4 Mobile Email 2.5 Drafts 2.6 Outbox 2.7 Sent 2.8 Voicemail 2.9 Templates 2.9.1 Text Templates 2.9.2 Multimedia Templates 2.9.3 Signature 2.0 Message Settings 2.0.1 Text Message 2.0.2 Multimedia Message 2.0.3 Voicemail 2.0.4 Download Messages 30
3. Entertainment (see page 46)
3.1 Shop Music 3.2 Games 3.3 Applications 3.4 MusicID 3.5 Streaming Music 3.6 Music Videos 3.7 The Buzz 3.8 Community
4. MEdia Net (see page 48)

IM Information

This indicates the Instant Messaging Client Information such as Client Name and Version Number.
Online Menu / 1 to 1 conversation
After a successful Login, a list of contacts with Screen Names will appear on screen. Depending on the cursor location in the contacts, the following menu options will be available.
When cursor is located on a Conversations List
The Conversations List contains both the active contact where a conversation has taken place as well as an unknown contact.
When cursor is located on a Conversation
] End Conversation: This closes the selected conversation. If an unknown contact was selected, that contact is deleted. ] Block/Unblock Contact: This allows you to block/unblock the selected Conversations Contact. ] View Information: This allows you to view the User ID and Status Text information. ] Search: This allows you to search for the contact by Email address or name. ] Settings: Please refer to the previous Settings Menu. ] Log Out: This begins the Logout process.
session or conversation. ] Saved Conversations: This is where a user can view saved conversations. ] Search: This allows you to search for the contact by Email address or name. ] Settings: Please refer to the previous Settings Menu. ] Log Out: This begins the Logout process.
When cursor is located on a Contact
] Add Contact: This adds a new contact to the selected contacts list; in the meantime this searches for the contact on the basis of E-mail Address, First Name, or Last Name. ] Delete Contact: This deletes the selected Contact. ] Block/Unblock Contact: This allows or blocks conversation with the selected Contact. ] Refresh Contact: This refreshes the present information on the selected contact. ] View Information: This allows you to view information. It provides User ID, Status Text. ] Search: This allows you to search for the contact by Email address or name.
When cursor is located on a Contact List
] Add Contact: This adds a new contact to the selected contacts list; in the meantime this searches for the contact on the basis of E-mail Address, First Name, or Last Name. ] Refresh List: This refreshes the present information on the contacts within the contacts. ] Send to Others: This offers the ability to send a message to an unknown contact. When selected, the User ID must be typed in prior to starting an IM

PTT Calls

A PTT call can only be made to individuals or groups you have established in your PTT Contacts. See PTT Contacts for instructions to set up individuals/groups. Making a PTT Call 1. Push and quickly release the PTT Key to access your contact list. To access frequently called numbers, Push and hold the PTT Key to access your PTT Call History. 2. Select the individual or group you want to call. Make sure an available icon is displayed next to the name.
Convert to Cellular During a PTT call the call originator may convert the call over to a cellular call. 1. Call originator selects Options and then selects Convert to Cellular. The originator no longer has to press the PTT key to be heard. 2. Other participants on the call will remain in a PTT call until they press the PTT Key. Call Waiting While on a PTT call you will be notified of incoming PTT calls. Accepting the incoming PTT call suspends the first call. Rejecting the incoming PTT call terminates it. While on a PTT call you will be notified of incoming cellular calls. Accepting the incoming cellular call suspends the PTT call. Rejecting the incoming cellular call forwards it to voicemail. While on a cellular call you will be notified of incoming PTT calls. Accepting the incoming PTT call suspends the cellular call. Rejecting the incoming PTT call terminates it.

How a PTT call works

When you make a PTT call, you can instantly speak to other Cingular PTT subscribers. During a PTT call only one person can speak at a time. You can tell whether it is your turn to speak by listening for the following tones: PTT Floor Held tone This tone plays when you press and hold the PTT Key. It indicates you have the floor and your speech will be heard by the other call participants. PTT Floor Release tone When you let go of the PTT Key you will hear this tone as will the other participants on the call. All of your speech prior to this tone has been heard by other participants. Others on the call are now aware that the floor is open and they have an opportunity to speak by pressing their PTT Key. Error tone If you attempt to speak by pressing your PTT Key and someone else still has the floor you will hear this tone.

The PTT Key

The black key on the left hand side of the phone is your PTT Key. Pressing and releasing this key while idle displays your PTT contacts. Pressing and holding this key while idle displays your PTT history. Pressing and holding this key while in a PTT call allows you to speak to the other call participants. To make a call press and release your PTT key to display your contacts. Select the person or group you wish to connect with and Press and Hold the PTT Key. n Note

Last Call

Length of the last call.

Received Calls

Length of the incoming calls.

Dialed Calls

Length of outgoing calls.

Audio & Ringtones

Menu 7.2

All Calls

Total length of all calls made and incoming calls received since the timer was last reset.
] Shop Tones: This menu option connects to Cingulars ringtone download site. ] Record Voice: You can record your own audio by pressing the center key [OK]. ] Files: You can view the audio files in the list.
Data Counter (Menu 7.1.6)
You can check the amount of data transferred over the network by using the GPRS (General Packet Radio Service) information option. In addition, you can also view how much time you are online. ] Data Time: You can check the duration of Last Session and All Session. You can also reset the call timers. ] Data Volume: You can check the Sent, Received or All data volumes and Reset all.

Graphics

Menu 7.3
] Shop Graphics: This menu option connects to Cingulars graphic download site. n Note
Additional charges may be incurred when downloading graphics. Contact your service provider for further information.
] Take Photo: You can take your own photo by pressing the center key [OK]. ] Make Animated GIF: You can make an animation file with the selected images in the list. ] Files: You can view the graphic files in the list.

Menu 7.4

pm using the center soft key. ] Repeat: Select the desired repeat mode using the navigation key. ] Alarm Tone: Select the alarm sound to use for the alarm using the key. ] Memo: Input alarm name.
] Record Video: You can record your own video by pressing the center key [OK]. ] Files: You can view the video files in the list. n Note
DRM (Digital Rights Management) Contents Copyright protected contents. DRM sometimes restricts some functions, such as send, and edit. The indicates content controlled by DRM protection.

Calendar (Menu 7.5.2)

When you enter this menu a calendar will be displayed. The square cursor is used to locate a particular day. The bottom bar on the calendar indicates schedule(s) for that day. This function helps to remind you of the schedule. The phone will sound an alarm tone if it has been set for a specific schedule item. Key up/down navigation key left/right navigation key key/ key/ key key Description Weekly Daily Annually Monthly

Measurement. The exposure limit takes into consideration the bodys ability to remove heat from the tissues that absorb energy from the wireless phone and is set well below levels known to have effects. Manufacturers of wireless phones must report the RF exposure level for each model of phone to the FCC. The FCC website (http://www.fcc.gov/oet/rfsafety) gives directions for locating the FCC identification number on your phone so you can find your phones RF exposure level in the online listing. 8. What has the FDA done to measure the radio frequency energy coming from wireless phones? The Institute of Electrical and Electronic Engineers (IEEE) is developing a technical standard for measuring the radio frequency energy (RF) exposure from wireless phones and other wireless handsets with the participation and leadership of FDA scientists and engineers. The standard, Recommended Practice for Determining the SpatialPeak Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques, sets forth the first consistent test methodology for measuring the rate
at which RF is deposited in the heads of wireless phone users. The test method uses a tissuesimulating model of the human head. Standardized SAR test methodology is expected to greatly improve the consistency of measurements made at different laboratories on the same phone. SAR is the measurement of the amount of energy absorbed in tissue, either by the whole body or a small part of the body. It is measured in watts/kg (or milliwatts/g) of matter. This measurement is used to determine whether a wireless phone complies with safety guidelines. 9. What steps can I take to reduce my exposure to radiofrequency energy from my wireless phone? If there is a risk from these products - and at this point we do not know that there is - it is probably very small. But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radiofrequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure. If you must conduct extended conversations by wireless phone every day, you could place more
distance between your body and the source of the RF, since the exposure level drops off dramatically with distance. For example, you could use a headset and carry the wireless phone away from your body or use a wireless phone connected to a remote antenna. Again, the scientific data do not demonstrate that wireless phones are harmful. But if you are concerned about the RF exposure from these products, you can use measures like those described above to reduce your RF exposure from wireless phone use. 10. What about children using wireless phones? The scientific evidence does not show a danger to users of wireless phones, including children and teenagers. If you want to take steps to lower exposure to radiofrequency energy (RF), the measures described above would apply to children and teenagers using wireless phones. Reducing the time of wireless phone use and increasing the distance between the user and the RF source will reduce RF exposure. Some groups sponsored by other national governments have advised that children be discouraged from using wireless phones at all. For example, the government in the

United Kingdom distributed leaflets containing such a recommendation in December 2000. They noted that no evidence exists that using a wireless phone causes brain tumors or other ill effects. Their recommendation to limit wireless phone use by children was strictly precautionary; it was not based on scientific evidence that any health hazard exists. 11. What about wireless phone interference with medical equipment? Radio frequency energy (RF) from wireless phones can interact with some electronic devices. For this reason, the FDA helped develop a detailed test method to measure electromagnetic interference (EMI) of implanted cardiac pacemakers and defibrillators from wireless telephones. This test method is now part of a standard sponsored by the Association for the Advancement of Medical instrumentation (AAMI). The final draft, a joint effort by the FDA, medical device manufacturers, and many other groups, was completed in late 2000. This standard will allow manufacturers to ensure that cardiac pacemakers and defibrillators are safe from wireless phone EMI. The FDA has tested hearing aids
for interference from handheld wireless phones and helped develop a voluntary standard sponsored by the Institute of Electrical and Electronic Engineers (IEEE). This standard specifies test methods and performance requirements for hearing aids and wireless phones so that no interference occurs when a person uses a compatible phone and a compatible hearing aid at the same time. This standard was approved by the IEEE in 2000. The FDA continues to monitor the use of wireless phones for possible interactions with other medical devices. Should harmful interference be found to occur, the FDA will conduct testing to assess the interference and work to resolve the problem. 12. Where can I find additional information? For additional information, please refer to the following resources: FDA web page on wireless phones (http://www.fda.gov/cdrh/phones/index.html) Federal Communications Commission (FCC) RF Safety Program (http://www.fcc.gov/oet/rfsafety) International Commission on Non-lonizing Radiation
Protection (http://www.icnirp.de) World Health Organization (WHO) International EMF Project (http://www.who.int/emf) National Radiological Protection Board (UK) (http://www.nrpb.org.uk/)
memorize the phone keypad so you can use the speed dial function without taking your attention off the road. 2. When available, use a hands-free device. A number of hands-free wireless phone accessories are readily available today. Whether you choose an installed mounted device for your wireless phone or a speaker phone accessory, take advantage of these devices if available to you. 3. Position your wireless phone within easy reach. Make sure you place your wireless phone within easy reach and where you can reach it without removing your eyes from the road. If you get an incoming call at an inconvenient time, if possible, let your voicemail answer it for you. 4. Suspend conversations during hazardous driving conditions or situations. Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow and ice can be hazardous, but so is heavy traffic. As a driver, your first responsibility is to pay attention to the road. 5. Do not take notes or look up phone numbers while driving. If you are reading an address book or

For more information, please call to 888-901-SAFE, or visit our website www.wow-com.com
Consumer Information on SAR (Specific Absorption Rate)
This Model Phone Meets the Governments Requirements for Exposure to Radio Waves. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. * Tests for SAR are conducted using
standard operating positions specified by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. Because the phone is designed to operate at multiple power levels to use only the power required to reach the network, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 1.14 W/kg and when worn on the body, as described in this users manual, is 0.998 W/kg. (Body-worn measurements differ among phones models, depending upon available accessories and FCC requirements.) While there may be differences between SAR levels of various phones and at various positions, they all meet the government requirement

Vehicle Mounted External Antenna (optional, if available)
A minimum separation distance of 8 inches (20cm) must be maintained between the user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCC website at www.fcc.gov

Battery Disposal

] Please dispose of your battery properly or bring to your local wireless carrier for recycling. ] Do not dispose in fire or with hazardous or flammable materials.
Adapter (Charger) Cautions
] Using the wrong battery charger could damage your phone and void your warranty. ] The adapter or battery charger is intended for indoor use only. Do not expose the adapter or battery charger to direct sunlight or use it in places with high humidity, such as the bathroom.
FCC Part 15 Class B Compliance
This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device and its accessories may not cause harmful interference, and (2) this device and its accessories must accept any interference received, including interference that may cause undesired operation.

Avoiding hearing damage

Permanent hearing loss may occur if you use your phone and/or headset at a high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected. Hearing experts suggest that to protect your hearing: ] Limit the amount of time you use your phone and/or headset at high volume. ] Avoid turning up the volume to block out noisy surroundings. ] Turn the volume down if you can't hear people speaking near you. For information about how to set a maximum volume limit on your phone, see the features guide for your phone.

Using your phone safely

Use of your phone while operating a vehicle is not recommended and is illegal in some areas. Be careful and attentive while driving. Stop using your phone if you find it disruptive or distracting while operating any type of vehicle or performing any other activity that requires your full attention.

Your Phone

Phone Components

1. Earpiece

9. Display screen 2. Navigation key 10. Message key
3. Left soft key 4. Side keys 5. Cingular Video key 6. Send key 7. Alpha numeric keys 8. Microphone 12
11. Right soft key 12. OK key 13. Task menu key 14. End /Power key 15. Clear key

Your Phones Features

1. Earpiece 2. Navigation key: Use for quick access to phone functions. 3,11. Left soft key/Right soft key: Each of these keys performs the functions indicated by the text on the display immediately above them. 4. Side keys: These keys are used to control the volume of the ring in standby mode and speaker volume during a call. 5. Cingular Video key: Press this key to access Cingular Video Folder. 6. Send key: You can dial a phone number and answer incoming calls. Press this key in standby mode to quickly access the most recent incoming, outgoing and missed calls quickly. 7. Alphanumeric keys: These keys are used to dial a number in standby mode and to enter numbers or characters in edit mode. 8. Microphone: Can be muted during a call for privacy. 9. Display screen: Displays phone status icons, menu items, Web information, pictures and more in full color.
10. Message key: Use to send text messages. 12. OK key: Press will launch the WAP browser. Allows you to select and confirm menu options. 13. Task menu key: Multitask simultaneously with voice and data - browse the web, make calls, play games, send and receive messages, and listen to MP3s. All at once. 14. End/Power key: Allows you to power the phone on or off, end calls, or return to Standby Mode. 15. Clear key: Allows you to delete the characters entered or to go back to the previous screen.
Speakerphone You can use the speakerphone during a call by pressing the or [speakerphone] key located on the top of the phone. The loudspeaker is automatically deactivated when you end the call. Camera Camera key - Press this key to use the camera feature or to go directly to camera mode.

Headset jack Side key PTT key - Use for quick access to the PTT function. Pressing and releasing this key while idle displays your PTT contacts. Pressing and holding this key while idle displays your PTT history. Pressing and holding this key while in a PTT call allows you to speak to the other call participants.

Backlight

A backlight illuminates the display and the keypad. When you press any key or open the folder, the backlight turns on. It turns off if no key is pressed within a given period of time, depending on the Backlight Timer menu option. After 30 seconds, the display turns off to conserve your battery power. To specify the length of time the backlight is active, set the Backlight Timer menu option (Menu 9.2.3).
External Display Your phone has an external display on the cover. It indicates when you have an incoming call or a message. It also alerts you at the specified time when you set an alarm by turning on its backlight and showing corresponding icon on it.

Display Information

Icon area

Text and graphic area

Soft key indications

First line Middle lines

Description
Displays various icons. Dispaly messages, instructions and any information that you enter, such as number to be dialed. Shows the functions currently assigned to the two soft keys.

Last line

On-Screen Icons
The table below describes various display indicators or icons that appear on the phones display screen. Icon Description
Indicates the strength of the 3G network signal. Indicates the strength of the network signal. Indicates that the EDGE service is available. Connection to the EDGE service allows you to transfer data at a speed of 200Kb/s(depending on network availability). Check with your operator for network coverage and service availability. Indicates that GPRS service is available. Indicates that Flight mode has been activated. Indicates the status of the battery charge. Indicates that a call is in progress. Indicates that the alarm has been set and is on. Indicates the Schedule function. Indicates the receipt of a message. Indicates the receipt of a Voicemail.
Indicates that Ring has been set for alert. Indicates that Ring and vibration has been set for alert. Indicates that Silent has been set for alert. Indicates that Vibration has been set for alert. Indicates that the speakerphone has been activated. Indicates that the Bluetooth function has been activated. Indicates that the data is being transmitted using a Bluetooth connection. Indicates that the connection to a headset with Bluetooth has been activated. Indicates that the Multitasking function has been activated. Indicates that the TTY has been set and is on. Indicates that the status of PTT is Available. Indicates that the status of PTT is Unavailable. Indicates that the status of PTT is Do Not Disturb. Indicates a PTT Message is waiting in the PTT Menu. Indicates that the phone is accessing the WAP. Indicates that Hearing Aid function has been activated.

If the battery fails to charge completely: ] After turning the phone on and off, please attempt to recharge the battery. ] After detaching and reattaching the battery, please attempt to recharge the battery.
3. When charging is finished, disconnect the travel charger from the phone by pressing on the grey tabs on both sides of the connector while pulling the connector out.
Turning Your Phone On and Off
1. Hold down the switches on. [END] key until the phone

n Note

] If your phone is powered on while charging, youll see the bars on the battery indicator icon cycle. ] While a phone is being charged, Charging. message is shown in the idle screen. ] When it is completed, Charge complete message is displayed in the same place. If a user cannot see the Charge complete message, even if battery icons are show 3 blocks, it means the phone is not charged fully yet.
2. If the phone asks for a PIN, enter the PIN and press the key. The phone searches for your network and after finding it goes to the idle screen as illustrated below. From the idle screen, you can make or receive a call.
The display language is preset to Automatic at the factory. To change the language, use the Languages menu option (Menu 9.2.5).
3. When you wish to switch the phone off, hold down the [END] key until the power-off image displays.

Access Codes

You can use the access codes described in this section to avoid unauthorized use of your phone. The access codes can be changed by using the Change Codes feature (Menu 9.6.4).

Security code (4 digits)

The security code protects the unauthorized use of your phone. The default security code is set to 0000 and the security code is required to delete all phone entries and to activate the Restore Factory Settings menu. The security code default setting can be modified from the Security Settings menu.

General Functions

Making a Call
1. Make sure your phone is powered on. 2. Enter a phone number including the area code. To edit a number on the display screen, simply press the key to erase one digit at a time.

] Press and hold the

Making International Calls
1. Press and hold the key and the international access character + will appear. 2. Enter the country code, area code, and the phone number. 3. Press the [SEND] key.

key to erase the entire

number. 3. Press the [SEND] key to call the number. [END] key. 4. When finished, press the

Ending a Call

When you have finished a call, press the key. [END]
Making a Call by Send Key
1. Press the [SEND] key, and the most recent incoming, outgoing and missed phone numbers will be displayed. 2. Select the desired number by using the navigation key. 3. Press the [SEND] key.
Making a Call From the Contacts
You can store names and phone numbers dialed frequently in the SmartChip as well as in the phone memory known as the Contacts. You can dial a number by simply selecting a name in the contacts and pressing the [SEND] key.

Adjusting the Volume

During a call, if you want to adjust the earpiece volume, use the side keys of the phone. In idle mode, you can adjust the ring volume using the side keys.
2. End the call by closing the phone or pressing the [END] key. n Notice
You can answer a call while using the Address Book or other menu features.

Answering a Call

When you receive a call, the phone rings and the flashing phone icon appears on the screen. If the caller can be identified, the callers phone number (or name if stored in your Address Book) is displayed. 1. Open the flip and press the [SEND] key or the left soft key to answer an incoming call. If Any Key has been set as the answer mode (Menu 9.5.4), any key press will answer a call except for the [END] key or the right soft key. n Note
] To reject an incoming call, press and hold the side keys on

Vibrate Mode (Quick)

Vibrate Mode can be activated by pressing and holding down the [Star] key.

Signal Strength

If you are inside a building, being near a window may give you better reception. You can see the strength of your signal by the signal indicator on your phones display screen.

Entering Text

You can enter alphanumeric characters by using the phones keypad. For example, storing names in the Address Book, writing a message, or creating scheduling events in the calendar all require entering text. The following text input methods are available on the phone.

the left side of the phone.
] If Flip Open has been set as the Answer Mode (Menu
9.5.4), you do not need to press any key. You can answer the call simply by opening the flip. 22
T9 Mode This mode allows you to enter words with only one keystroke per letter. Each key on the keypad has more than one letter. The T9 mode automatically compares your keystrokes with an internal linguistic dictionary to determine the correct word, thus requiring far fewer keystrokes than the traditional ABC mode. ABC Mode This mode allows you to enter letters by pressing the key labeled with the required letter once, twice, three or four times until the letter is displayed. 123 Mode (Numbers Mode) Type numbers using one keystroke per number. To change to 123 mode in a text entry field, press key until 123 mode is displayed. A long press changes the mode to 123. Symbol Mode This mode allows you to enter special characters. n Note
You can select a different T9 language from the menu option. The default setting on the phone is T9 disabled mode.
Changing the Text Input Mode Change the text input mode by pressing. You can check the current text input mode in the upper right corner of the screen. Using the T9 Mode The T9 predictive text input mode allows you to enter words easily with a minimum number of key presses. As you press each key, the phone begins to display the characters that it thinks you are typing based on a built-in dictionary. As new letters are added, the word changes to reflect the most likely candidate from the dictionary. 1. When you are in the T9 predictive text input mode, start entering a word by pressing keys to Press one key per letter. ] The word changes as letters are typed - ignore whats on the screen until the word is typed completely. ] If the word is still incorrect after typing completely, press the [Star] key once or more to cycle through the other word options. ] If the desired word is missing from the word choices list, add it by using the ABC mode.
2. Enter the whole word before editing or deleting any keystrokes. 3. Complete each word with a space by pressing the key or the right navigation key. To delete letters, press. Press and hold down to erase the letters continuously. n Notice

To exit the text input mode without saving your input, press the [END] key.
Refer to the table below for more information on the characters available using the keys.

Key 9 0

Characters in the Order Display Upper Case.,'@?!-:/1 ABC2 DEF3 GHI4 JKL5 MNO6 PQRS7 TUV8 WXYZ9 Lower Case.,'@?!-:/1 abc2 def3 ghi4 jkl5 mno6 pqrs7 tuv8 wxyz9
Using the ABC Mode Use the keypad keys to enter your text. 1. Press the key labeled with the required letter:
] Once for the first letter ] Twice for the second letter ] And so on
2. To insert a space, press the key once. To delete letters, press the key. Press and hold down the key to erase the letters continuously.
Space Key, 0 (Long press) Space Key, 0 (Long press)
Using the 123 (Numbers) Mode The 123 Mode enables you to enter numbers in a text message (a telephone number, for example) more quickly. Press the keys corresponding to the required digits before manually switching back to the appropriate text entry mode. Using the Symbol Mode The Symbol Mode enables you to enter various symbols or special characters. To enter a symbol, press the [Star] key. Use the navigation keys to select the desired symbol and press the [OK] key. T9 dictionary The T9 dictionary is a feature that allows the user to add any unique or personal words to the T9 standard language database. The T9 dictionary function can be selected from the Text Entry Settings sub menu under the Options soft key menu. Within the T9 dictionary function, the user can add, modify, delete or reset personal words.
Selecting Functions and Options
Your phone offers a set of functions that allow you to customize the phone. These functions are arranged in menus and sub-menus, accessed via the two soft keys marked the left soft key and the right soft key. Each menu and sub-menu allows you to view and alter the settings of a particular function. Soft key functions vary depending on the mode of the phone. The label on the bottom of the display screen immediately above the soft keys indicates the current function.

You cannot edit and delete pre-installed accounts.
Cache Settings (Menu 4.6.2)
The web pages you have accessed are stored in the memory of the phone. ] Clear Cache: Remove all cached data in the memory. ] Allow Cache: Set a value to determine whether a connection attempt is made through the cache or not. n Note
A cache is a buffer memory, which is used to store data temporarily, especially when it is online.
Character Encoding (Menu 4.6.4)
Select a character set from the following list: 1 Automatic 3 English(ISO) 5 Unicode(UCS2 BE) 7 Unicode(UCS2 Auto) 9 Unicode(UTF-16 LE) * Unicode(UTF-8) 2 English(ASCII) 4 English(LATIN) 6 Unicode(UCS2 LE) 8 Unicode(UTF-16 BE) 0 Unicode(UTF-16 Auto)
Scrolling Control (Menu 4.6.5)
This allows you to determine the scroll speed and select from 1 Line, 2 Lines or 3 Lines.
Cookie Settings (Menu 4.6.3)
The information or services you have accessed are stored in the cookie. ] Delete Cookies: Remove all cookies. ] Allow Cookies: Set a value to determine whether a connection attempt is made through the cookie or not.

Show Image (Menu 4.6.6)

This allows you to view pictures when browsing.

AuthWallet (Menu 4.6.7)

If set to On, the users personal information such as ID and Password used to access the Internet site will be saved automatically for future use.

Online menu

Once you are connected to the Internet, the following menu options are available: ] Back: Moves to the previous page. ] Forward: Moves to the next page. ] Reload: Loads the current page again. ] Home: Moves to the initial homepage. ] Go to URL: Connects to the specific URL after editing. ] Bookmarks: You can add or save the current page to Bookmark or view the list saved under Bookmark. ] Settings: You can set browser related options such as Clear cache, Clear cookies, etc.

Cingular Mall

Shop Tones

Menu 5.1

Shop Multimedia

Menu 5.4

This menu option connects to Cingulars ringtone download site. n Note
Additional charges may incur when downloading ringtones. Contact your service provider for further information.
This allows you to connect to Cingular's multimedia download site. n Note

Shop Games

Menu 5.2

Shop Applications

Menu 5.5
This menu option connects to Cingulars game download site. This allows users to download the various games by connecting to the Internet. n Note

This contact has turned PTT Off, powered down their phone, or moved out of coverage.

Do Not Disturb

This contact is not receiving PTT calls.
This becomes your availability state if you change My Availability (Menu 6.4.1) to Do Not Disturb. In this state you may place PTT calls but will not receive a PTT call.

Silent/Vibrate

This contact is available to receive PTT calls. However they will be given the option to accept or reject your PTT call.

PTT Message

This icon appears in place of your availability status notifying you that a PTT message is waiting. To access these messages go to Push to Talk (6) on the Main Menu. The message will either immediately display or may be found under Pending Invitations (5).

Invitation in Progress

You are waiting for this contact to accept your invitation.

GROUPS: Available

At least one member of the group is available to talk.
] PTT Contact Availability: This section covers the icons which will appear next to individuals and groups in your PTT Contacts list indicating their availability. INDIVIDUALS: Available
This contact is available to talk.
Every member has powered down their phone, turned PTT Off, or moved out of coverage.
None of the members of the group can be contacted.
All members of the group are available to receive a PTT call but each will be given the option to accept or reject your call.
Calls can not be placed to Quick Group or Dynamic Group in your PTT Call History.
You have sent an invitation to join a group and none of the members have yet accepted. Once one member accepts this status will change and calls will complete to all members who have accepted and are available.
3. Press and hold the PTT Key to activate the call. A tone will immediately play indicating you have the floor and may begin speaking. 4. Release the PTT Key when you are done speaking. Receiving a PTT Call 1. For the best experience your ringer should be set to the highest possible volume. 2. If your status is Available you will hear a PTT Call tone and then the caller's voice. 3. If your status is Vibrate All your phone will vibrate and then you must accept or reject the call. If set to Silent their will be no call notification tone. a. Accepting the call then plays the callers voice over the earpiece. b. Rejecting the call terminates the call. PTT calls are not forwarded to voicemail.

PTT Calls

A PTT call can only be made to individuals or groups you have established in your PTT Contacts. See PTT Contacts for instructions to set up individuals/groups. Making a PTT Call 1. Push and quickly release the PTT Key to access your contact list. To access frequently called numbers, Push and hold the PTT Key to access your PTT Call History. 2. Select the individual or group you want to call. Make sure an available icon is displayed next to the name.

Add Contact

1. Select Add Contact in the PTT menu.

Menu 6.2

2. Enter the contact's name and phone number and then select [Save]. An invitation to join your PTT Contacts will be sent. 3. The availability icon will be Invitation in Progress until the individual accepts. 4. Once accepted they are part of your PTT Contacts and you are part of theirs.
4. When a participant accepts your invitation the group is now in their PTT Contacts and they may also place calls to the group. 5. Maximum members in a group is 30, 29 participants and yourself. You may have up to 30 groups in your PTT Contacts.
] Set Your Name: When you initialized service you set a name for yourself. This name is presented in Contact Invitations. Changing your name will not impact invitations already sent but will be reflected in future invitations. ] Auto Accept Invites: If you do not want to prescreen all additions to your PTT Contacts you can use this menu item to automatically accept your invitations. Enable All automatically accepts all invitations. Contact Only automatically accepts individual invitations. Group Only automatically accepts group invitations. Disable All allows you to pre-screen all invitations. ] PTT is On/PTT is Off: This menu item allows you to turn your PTT Service off or turn it on.

PTT Settings

Menu 6.4
] My Availability: This option allows you to change your Availability status between Do Not Disturb and Available. ] Contact Alerts: This feature allows you to be alerted when the availability status of a contact changes from Unavailable or Do Not Disturb to Available or Silent/Vibrate. 1. Once Contact Alerts is selected a list of individuals from PTT Contacts will display. Select those individuals for whom you want to receive alerts for availability changes. 2. Once selected you will receive alerts for availability changes until you de-select them. 3. An alert consists of a tone as well as a PTT message when you access the PTT Menu.

Pending Invitations

Menu 6.5
This menu item only displays if you have invitations which have been waiting for your review. Selecting this menu item displays a list of invitations pending. Invitations not disposed of within 7 days will expire.

My Stuff

Recent Calls
Menu 7.1 Delete the call from the list
You can check the record of missed, received, and dialed calls only if the network supports Calling Line Identification (CLI) within the service area. The number and name (if available) are displayed together with the date and time of the call. You can also view call times.

call duration or when games are played or even when surfing the Internet for a long time. This has no effect upon the life of the product or performance.
A When frequency is unstable or weak or if there are
too many users, connection may be cut off even after it was established. Please try again later or attempt after relocating to other areas.
Q Why does the battery life get shorter in standby mode? A The battery is worn out. As time passes, the battery
life gradually becomes shorter. If the battery lasts about half the amount of time as when first purchased, its time to purchase a new battery.
Q I cannot find the lock, PIN, or PUK code. What is my

password?

A The default lock code is 0000. If you forget or lose
the lock code, contact your phone dealer. If you forget or lose a PIN or PUK code, or if you have not received such a code, contact your network service provider.
Q Why does the battery run out so quickly during

normal use?

A It is due to the user environment or a large number
of calls or a weak signal.
Q Why is no number dialed when you recall an

Address Book entry?

A Check that the number has been stored correctly by
using the Address book Search feature. Re-store them, if necessary.

Accessories

There are a variety of accessories available for your mobile phone. You can select these options according to your personal communication requirements. Consult your local dealer for availability.

Travel Adapter

This adapter allows you to charge the battery. It supports standard U.S. 120 Volt 60Hz outlets. It takes under 4 hours to charge a completely discharged battery.

Battery

Standard battery is available.

Vehicle Power Adapter

You can operate the phone and trickle charge the phone battery from your vehicle by using the vehicle power adapter. It takes 5 hours to charge a completely discharged battery.
Always use genuine LG accessories. Failure to do this may invalidate your warranty. Accessories may be different in different regions; please check with our regional service company or agent for further enquiries.

situations with your phone at your side, help is only three numbers away. Dial 911 or other local emergency number in the case of fire, traffic accident, road hazard or medical emergency. Remember, it is a free call on your wireless phone! 9. Use your wireless phone to help others in emergencies. Your wireless phone provides you a perfect opportunity to be a Good Samaritan in your community. If you see an auto accident, crime in progress or other serious emergency where lives are in danger, call 911 or other local emergency number, as you would want others to do for you. 10. Call roadside assistance or a special wireless nonemergency assistance number when necessary. Certain situations you encounter while driving may require attention, but are not urgent enough to merit a call for emergency services. But you can still use your wireless phone to lend a hand. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one appears injured or a vehicle. you know to be stolen, call roadside assistance or other special non-emergency wireless number.
For more information, please call to 888-901-SAFE, or visit our website www.wow-com.com
Consumer Information on SAR (Specific Absorption Rate)
This Model Phone Meets the Governments Requirements for Exposure to Radio Waves. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. * Tests for SAR are conducted using