Website:http://www.LGservice.com [For U.S.A] www.lg.ca [For Canada]
ELECTRIC & GAS DRYER SERVICE MANUAL

CAUTION

READ THIS MANUAL CAREFULLY TO DIAGNOSE TROUBLES CORRECTLY BEFORE OFFERING SERVICE.
MODEL : DLE5977W/DLG5988W DLE5977B/DLG5988B DLE3777W/DLG3788W
Feb. 2004 PRINTED IN KOREA

P/No.:3828EL3005A

IMPORTANT SAFETY NOTICE
The information in this service guide is intended for use by individuals possessing adequate backgrounds of electrical, electronic, and mechanical experience. Any attempt to repair a major appliance may result in personal injury and property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use.

! WARNING !

To avoid personal injury, disconnect power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks.
RECONNECT ALL GROUNDING DEVICES
If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light a match, or cigarette, or turn on any gas or electrical appliance. Do not touch any electrical switches. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbors phone. Follow the gas suppliers instructions carefully. If you cannot reach your gas supplier, call the fire department.

IMPORTANT

Electrostatic Discharge (ESD) Sensitive Electronics ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance. - OR -
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
Before removing the part from its package, touch the anti-static bag to a green ground connection point or unpainted metal in the appliance. Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only. When repackaging failed electronic control assembly in anti-static bag, observe above instructions.

CONTENTS

1. SPECIFICATIONS....4 2. FEATURES AND BENEFITS.... 5 3. INSTALLATION INSTRUCTIONS... 6 4. DRYER CYCLE PROCESS.... 12 5. COMPONENT TESTING INFORMATION...13 6. MOTOR DIAGRAM AND SCHEMATIC....16 7. CONTROL LAY - OUT....17 8. WIRING DIAGRAM...18 9. DIAGNOSTIC TEST....19 9-1. TEST 1 120VAC ELECTRICAL SUPPLY...20 9-2. TEST 2 THERMISTOR TEST --- MEASURE WITH POWER OFF..21 9-3. TEST 3 MOTOR TEST...22 9-4. TEST 4 MOISTURE SENSOR...23 9-5. TEST 5 DOOR SWITCH TEST...24 9-6. TEST 6 HEATER SWITCH TEST - ELECTRIC TYPE...25 9-7. TEST 7 GAS VALVE TEST - GAS TYPE...26 10. CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS)..27 11. DISASSEMBLY INSTRUCTIONS....29 12. EXPLODED VIEW....36 12-1. CONTROL PANEL & PLATE ASSEMBLY...36 12-2. CABINET & DOOR ASSEMBLY...37 12-3-1. DRUM & MOTOR ASSEMBLY : ELECTRIC TYPE...38 12-3-2. DRUM & MOTOR ASSEMBLY : GAS TYPE...39 13. REPLACEMENT PARTS LIST

SPECIFICATIONS

ITEM DLE5977W DLG5988W DLE5977B DLG5988B Black DLE3777W DLG3788W Blue White Painted Blue White REMARK
Color Material & Finishes Top Plate Door Trim POWER SUPPLY MOTOR ELECTRICITY CONSUMPTION HEATER LAMP GAS VALVE CONTROL TYPE DRUM CAPACITY Weight (lbs): Net / Gross No. of Programs No. of Dry Option No. of Temperature Controls No. of Dry Levels Audible End of Cycle Beeper Sensor Moisture Temperature Reversible Door Drum Dryer Rack Child Lock Interior Light Product (WXHXD) Packing (WXHXD)

Blue White

Porcelain Chromate + STS Deco
120V / 240V 60Hz (26A) 250W (4.5A) 5400W (22.5A) 15W (125mA) 13W (110mA) X 2 Electronic 7.3 cu.ft. 126 / 144
AC 120V AC 240V ( ELECTRIC TYPE) AC 120V AC 120V ( GAS TYPE)

High / Low / Off

Equipped Equipped Adopted Stainless Steel Equipped Equipped Equipped
Electro sensor Thermistor
27" x 42 3/4" x 28 1/3"
29 1/2" x 44 3/4" x 30 3/4"

FEATURES AND BENEFITS

DLE5977W/DLG5988W/DLE5977B/DLG5988B

DLE3777W/DLG3788W

INSTALLATION INSTRUCTIONS
Review the following options to determine the appropriate electrical connection for your home: 3-wire receptacle (NEMA type10-30R)
Use the instructions at this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord.
4-wire connection : Direct wire
Important : The places where a 4-wire connection is needed are , for example, mobile homes and areas that local codes do not admit the use of 3-wire connections. At least, 5ft(1.52m) of extra length is required in order for dryer to be able to be moved. Peel 5 in (12.7cm) of external covering from end of cable, leaving bare ground wire at 5 in (12.7cm). Cut 11/2 in. (3.8cm) from 3 remaining wires. Peel insulation back 1in. (2.5cm). Shape ends of wires like a hook. 1" m)

(2. 5c

5" (12.7 cm) 31/2" (8.6 cm)
4-wire receptacle (NEMA type14-30R)
Use the instructions at this section if your home has a 4-wire receptacle (NEMA type 14-30R) and you will be using a UL listed, 120/240 volt minimum, 30 amp, dryer power supply cord.

5 (12.7 " cm)

5" (12.7 cm)

31/2" (8.6 cm)

3 wire direct
Then, put the hooked shape end of the wire under the screw of the terminal block(hooked end facing rightward) and pinch the hook together and screw tightly.
If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker 1" ) 1" ) cm box cm 5 (2. (2.5 1.Take off center terminal block screw 2.Take off appliance neutral ground wire(white) from external ground connector screw. Fasten it under center, silver colored terminal block screw. 3.Connect ground wire(green) of power supply cable to external ground conductor screw. Tighten screw.

1" ) cm 2.5 (

3V2" ) (8.9 cm

4 wire direct

If this type is available at your home. you will be connecting to a fused disconnect or circuit breaker 1" m) box 5c (2.

a. b. c. d. e. f.

d e f c
External ground connector Green copper wire of power supply cord 3/4 in. (1.9cm) UL-listed strain relief Center silver-colored terminal block screw Neutral grounding wire(white) Neutral wire(white or center wire)
4. Put the hooked shape ends of the wire under the screw of the terminal block(hooked end facing rightward) and squeeze the hook together and screw tightly. 5. Put the hooked shaped ends of the other power supply cable wires under the outer terminal block screws(hooked end facing right) and squeeze the hooked ends together and screw tightly.

1. Take off center terminal block screw 2. Put the hooked end of the neutral wire(white) of power supply cable under the center screw of terminal block). Squeeze the hooked end together 3. Connect the hooked ends of the other power supply cable to the center screw of terminal block. 4. Screw strain relief tightly. 5. Place tab of terminal block cover into slot of dryer rear panel. Make sure cover with screw.
6. Tighten strain relief screws. 7. Place the tab of terminal block cover into slot of dryer rear panel. Make sure cover with screw.
3-wire connection : Direct wire
Important : The places wherea 4-wire connection is needed are mobile homes and areas that local codes do not admit the use of 3-wire connections. At least, 5ft(1.52m) of extra length is required for dryer to be able to move. Peel 5 in (12.7cm) of external covering from end of cable," leaving bare ground wire at 5 in (12.7cm). 3 (8.6 1/2 cm) (3.8cm) from 3 remaining wires. Strip Cut 1 in. insulation back 1in. (2.5cm). Shape ends of wires into a hook shape.

c b d a e

1" m) c

1" (2.5

a. b. c. d. e.
External ground connector Neutral grounding wire (white) Center silver-colored terminal block screw Neutral wire (white or center wire) 3/4 in. (1.9 cm) UL-listed strain relief
Option 1: 3-Wire Connection with a Power Supply Cord
lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under Section 3: Optional 3-wire connection.

a. b. c. d. e. f. g.

3-wire receptacle (NEMA type 10-30R) 3-wire plug Neutral prong Spade terminals with up turned ends 3/4 in. (1.9 cm) UL approved strain relief Ring terminals Neutral (white or center wire)
1. Loosen or remove center terminal block screw. 2. Connect neutral wire (white or center wire) of power supply cord to the center, silver colored terminal screw of the terminal block. Tighten screw.

a. b. c. d.

External ground connector Neutral grounding wire (white) Neutral wire (white or center wire) Grounding path determined by a qualified electrician
4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. Connect a separate copper ground wire from the external ground connector screw to an adequate ground.
3-2. Connect Gas Supply Pipe (Gas Dryer ONLY)
For further assistance, refer to section on Gas Requirements.
1. Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 N.P.T. gas connection. 2. Remove the shipping cap from the gas connection at the rear of the dryer. Make sure you do not damage the pipe thread when removing the cap. 3. Connect to gas supply pipe using a new flexible stainless steel connector. 4. Tighten all connections securely. Turn on gas and check all pipe connections (internal & external) for gas leaks with a non-corrosive leak detection fluid. 5. For L.P. (Liquefied Petroleum) gas connection, refer to section on Gas Requirements.
1 New Stainless Steel Flexible Connector - Use only if allowed by local codes (Use Design A.G.A. Certified Connector) 2 1/8 N.P.T. Pipe Plug (for checking inlet gas pressure) 3 Equipment Shut-Off Valve-Installed within 6 (1.8 m) of dryer
4 Black Iron Pipe Shorter than 20 (6.1 m) - Use 3/8 pipe Longer than 20 (6.1 m) - Use 1/2 pipe 5 3/8 N.P.T. Gas Connection

DRYER CYCLE PROCESS

Default Cycle Conditions of operation and termination Drying Cooling Wrinkle care Time
Temp- Dry Display erature Level time Electro- Temp- Default Tempsensor Control time Control**
HIGH (Normal) 54min Saturation 684C (5min) 475C MID (Normal) 55min Saturation 664C (5min) 475C HIGH MEDIUM (Normal) 41min Saturation 604C (5min) 475C
HEAVY DUTY COTTON/ TOWELS NORMAL PERM PRESS DELICATES ULTRA DELICATE SPEED DRY

Sensor Dry *

3Hr LOW LOW (Normal) 36min Saturation 523C (5min) 475C (Normal) 32min Saturation 523C (5min) 385C
ULTRA (Normal) 34min Saturation 453C (5min) 385C LOW (HIGH) (MID HIGH) 25min Saturation (705C) (5min) (475C) 20min 30min Saturation (665C) (5min) (475C) Saturation No heater N/A N/A Off Time: 6min 3Hr

Manual FRESHEN UP Dry **

AIR DRY

On Time: 10sec

Temperature Control for each cycle

Heater

* Sensor dry : Dry Level is set by users. ** Manual dry : Temperature control is set by users. Default settings can be adjusted by users.
COMPONENT TESTING INFORMATION
CAUTION When checking the Component, be sure to turn the power off, and do voltage discharge sufficiently.
Component Test Procedure Check result Remark

1. Thermal cut off

Check Top Marking : N130 2. Hi limit Thermostat (Auto reset)
Measure resistance of terminal If thermal fuse is open must Heater caseto terminal be replaced Safety 12F Electric type Open at 266 Resistance value (130 7C) Auto reset -31F (-35C) Continuity (250F ) < 1 Same shape as Outlet Thermostat. Measure resistance of terminal to terminal Open at 257 9F (125 5C) Close at 221 9F (105 5C) Measure resistance of terminal to terminal Open at 185 9F (85 5C) Close at 149 9F (65 5C) Same shape as Thermal cut off. Measure resistance of terminal to terminal Heater case Hi limit Electric type

Resistance value

Resistance value < 5 Blow housing Safety Electric type
3. Outlet Thermostat ( Auto reset)

Resistance value < 5

Check Top Marking : N85 4. Lamp holder
Resistance value : 80 ~ 100

5. Door switch

Measure resistance of the following terminal 1) Door switch knob : open Terminal : COM - NC (1-3) Terminal : COM - NO (1-2) 2) Door switch push : push Terminal : COM - NC (1-3) Terminal : COM - NO (1-2) Measure resistance of the following terminal : COM - NC
Resistance value < 1 Resistance value Resistance value Resistance value < 1 1. lever open Resistance value < 1 2. Lever push (close) Resistance value
The state that Knob is pressed is opposite to Open condition.

6. Idler switch

Component

7. Heater

Test Procedure
Measure resistance of the following terminal Terminal : 1 (COM) - 2 Terminal : 1 (COM) - 3 Terminal : 2 - 3 Measure resistance of terminal to terminal Temperature condition : 58F ~ (10~40C) 58F ~ 104F (10~40C)

Check result

Remark

Electric type

Resistance value : 10 Resistance value : 10 Resistance value : 20 Resistance value : 10 Heater case Hi limit Electric type

8. Thermistor

9. Motor

See Page 13

10. Gas valve

valve 1

Measure resistance of the following terminal Valve 1 terminal Valve 2 terminal
Gas type Resistance value : > 1.5kg ~ Resistance value : > 1.5~2.5kg

valve 2

11. Igniter
Measure resistance of terminal to terminal
Resistance value : 100~800 Gas type

12. Frame Detect

Measure resistance of terminal to terminal Open at 370F ((Maximum) Close at 320F
Gas type Resistance value Resistance value < 1
13. Outlet Thermostat (Auto reset)
Measure resistance of terminal to terminal Open at 203 7F (95 5C) Close at 158 9F (70 5C)

Gas type Gas funnel

Resistance value Continuity < 1
Check Top Marking : N95 13. Outlet Thermostat (Manual reset) Measure resistance of terminal to terminal Open at 212 12F (100 7C) Manual reset If thermal fuse is open must be replaced Resistance value Continuity < 1 Gas type Gas funnel

Check Top Marking : N100

MOTOR DIAGRAM AND SCHEMATIC
NOTE When checking Component, be sure to turn Power off, then do voltage discharge sufficiently.
Contact On / Off by Centrifugal Switch
STOP MODE (When Motor does not operate)
RUN MODE (Motor operates)

Centrifugal switch

Centrifugal switch (Pull Drive forward)

CONTROL LAY - OUT

PWB ASSEMBLY DISPLAY LAY-OUT
MODEL DISPLAY AS DIAGNOSTIC TEST
DLE5977W/B DLG5988W/B DLE3777W DLG3788W X X X X

OPTION PART

X X X X

X O X O

O O X X

LED DISPLAY

18:FO 19:FO 18:F1 19:F1
6871EC1115A 6871EC1115B 6871EC1115C 6871EC1115D

PWB ASSEMBLY LAY-OUT

WIRING DIAGRAM
ELECTRIC DRYER WIRING DIAGRAM

GAS DRYER WIRING DIAGRAM

DIAGNOSTIC TEST
1. This TEST should be used for Factory test /Service test. Do not use this DIAGNOSTIC TEST other than specified. 2. Activating the Heater manually with the Door open may trip the Thermostat attached to the Heater, therefore do not activate it manually. (Do not press the door switch to operate the heater while the door is open )
ACTIVATING THE DIAGNOSTIC TEST MODE
1. Unit must be in Standby (unit plugged in, display off) 2. Press POWER while pressing MORE TIME, and LESS TIME simultaneously.
Pressing the START/PAUSE button

CHECKING ACTION

DISPLAY

CHECKING POINT

Wont power up Defective LED Thermistor open

REMARK

See test 1 Display : See page See test 2
Electric control & Temperature sensor
Thermistor close Motor runs See test 3
70 ~ 239 Displays Moisture Sensor Operation: Measured If moisture sensor is contacted with Moisture Value. damp cloth. The display number is below 180, in normal condition. ELECTRIC TYPE : Heater runs GAS TYPE : GAS Valve runs (Display the Temperature of Inside drum.)

See test 4

3 times
ELECTRIC TYPE Motor + Heater 1 (2700W) GAS TYPE Motor + Valve ELECTRIC TYPE Motor + Heater 1 +Heater 2 (5400W) GAS TYPE Motor Type Control Off

Current Temp.

Gas valve See test 7

Current Temp. (5 ~ 70)

4 times
Auto Off Door switch Lamp Press Start button 1 time and then open the door. Proceed again with the step 1(by pressing start 1 time), step 2(by pressing start 2 times), step 3(by pressing start 3 times) and step 4(by pressing start 4 times) in sequence. Press Start 2 times and then open the door. Proceed again from the step 1 all the way to the step 4. Press Start 3 times and then open the door Proceed with the step 1 and skip the step 2 and press step 3 twice and finish with step 4 by making sure the all the electric devices shut off in the end. See test 6
Motor & Heater Off + Lamp On + During check, Buzzer beeps seven times If the door is open.
Motor on & Heater During check, Off + Lamp Off If the door is closed.

70 ~ 239

Test 1 120VAC Electrical supply

Caution

When measuring power, be sure to wear insulated gloves, to and avoid an electric shock.
Trouble Symptom No power was applied to Controller. (LED, Display off) Measurement Condition With Dryer Power On; Connector linked to Controller.
Check the outlet, is the voltage 110V ~ 125V AC?
Check the fuse or circuit breaker.
Check if the voltage measured between Connector RD3- (Black) linked to the Controller and WH3- (White) is 110V ~ 125V?
Check if Power Cord is properly connected.
N(White) L (Black) L (Led)
Check if the Controller wire is disconnected. Check if Terminal Block and Power Cord are connected (Check Plug ). - Does Power Cord N( Natural) line match to Terminal Center N(Natural) line?

Reconnect the controller.

Replace controIler.

Test 2 Thermistor Test --- Measure with Power Off
Before measuring resistance, be sure to turn Power off, and do voltage discharge. (When discharging, contact the metal plug of Power cord with the Ground.) During Diagnostic Test, tE1 and tE2 Error occur. During operation, Heater would not turn off, or remains on. Difference between actual and sensed temperature is significant.

Trouble Symptom

Measurement Condition After turning Power off, measure the resistance.
Check if Control and 6Pin connector is properly connected. Replace Controller.
Take 6pin Connector from the Controller.
Check if resistance is in the range of Table 1 when measuring 6pin connector Pin YES (Blue wire) and Pin (Red wire) connected to Controller.
Check if resistance is in the range of Table 1 when measuring resistance between terminals after separating Harness From Thermistor assembly Connector.

Replace Thermistor.

Check Harness-linking connector. Table 1. Resistance for Thermistor Temperature.
Air TEMP.[F (C)] RES. [k] Air TEMP.[F (C)] RES. [k] Air TEMP.[F (C)] RES. [k]
50F (10C) 60F (16C) 70F (21C) 80F (27C) 18.0 14.2 11.7 9.3 90F (32C) 100F (38C) 110F (43C) 120F (49C) 7.7 6.2 5.2 4.3 130F (54C) 140F (60C) 150F (66C) 160F (71C) 2.9 3.0 2.5 2.2

Test 3 Motor test

Before measuring resistance, be sure to turn Power off, and do voltage discharge. (When discharging, contact the metal plug of Power cord with earth line.)
Trouble Symptom Drum will not rotate; No fan will function; No Heater will work. Measurement Condition Turn the Dryers Power Off, then measure resistance.
Replace Control. (Relay check) Check Controller connector. Check if Door flame presses door switch knob. Check Door Switch. Check Harness connection. Replace Control. (Relay check) Check Controller connector. Replace Outlet Thermostat. (Refer to Component) Check Idler Assembly. Drum Belt cuts off Drum Belt takes off from Motor Pulley. Replace Idler Switch.
Is resistance below 3 between Connector WH3- (White wire) and BL2- (Brown wire)? YES Measure while door is closed.
Is resistance below 3 between Connector WH3- (White wire) and BL2- (Yellow wire)? NO Measure while door is closed.
Is resistance below 3 between Connector BL2- (Yellow wire) and BL2- (Brown wire)? YES
Is resistance below 1 between terminals NO of Outlet Thermostat attached to blower housing?

Test 6 Heater switch test - Electric Type
Before measuring resistance, be sure to turn Power off, and do voltage discharge. (When discharging, contact the metal plug of Power cord with earth line.) While operating, Heating will not work.
Trouble Symptom Drying time takes longer.
1. Is resistance between Heater terminal and below 18 ~ 22? 2. Is resistance between Heater terminal and below 18 ~ 22? 3. Is resistance between Heater terminal and below 9 ~ 11?

Replace Heater.

Check if the value of measured resistance is below 1 between terminal TH2 (Safety Thermostat). NO

TH3 TH2

Replace TH2 (Safety Thermostat).
Check if the value of measured resistance is below NO 1 between terminal TH3 (HI-Limit Thermostat). Replace TH3 (HI-Limit Thermostat).
Check Motor. Check if the value of measured resistance is below 1 between terminal and at RUN condition.
Check Motor and replace it.
Check Controller. Check Harness-linking Connector.
Test 7 GAS Valve test - Gas Type
When measuring power, be sure to wear insulated gloves, to avoid electric shock.
Trouble Symptom Drying time takes longer. Measurement Condition With dryer power on
While operating, Heating will not work.
Power On & Start (Normal Cycle)

Valve 1

When measuring Valve 1 voltage, More than AC 90V?
Check thermostat Hi limit Safety
Igniter operates? (after 1 min, Igniter becomes reddish)

Igniter

Valve 2
Check Igniter & Frame detect
When measuring Valve 2 voltage, Value is more than AC 90V? (10 sec after Igniter off) Check Gas connection or Gas supply
When measuring terminal resistance on Valve 1, Valve 2, Value is more than1.5 ~ 2.5k? (Measure after Off )

Change Valve

Harness check Controller change
CHANGE GAS SETTING (NATURAL GAS, PROPANE GAS)
After Natural Gas Setting, applying Propane Gas Orifice or wrong use of Natural Gas Orifice will result in fire. Conversion must be made by a qualified technician.

Warning

Initially, Natural Gas mode is

STEP 1 : VALVE SETTING

set. Propane Gas Orifice is on sale as a Service Part to authorized servicers only.

Full open

Change screw

STEP 2 : ORIFICE CHANGE

Remove 2 screws. Disassemble the pipe assembly. Replace Natural Gas orifice with Propane Gas orifice.

Gas type

Orifice P/No Marking

NCU PCU

Natural Gas 4948EL4001B Propane Gas 4948EL4002B

Orifice

Kit contents : Orifice (Dia. = 1.613mm, for Propane Gas) : Replace Label : Instruction sheet

GAS VALVE FLOW

START KEY PUSH VALVE 1 ON IGNITE ON
IGNITE TEMPERATURE ABOUT 370F
FRAME DETECT OPEN IGNITE OFF VALVE 2 ON

GAS IGNITION

FRAME DETECT CLOSE VALVE 2 OFF

DRYING

START VALVE 1 IGNITER FRAME DETECT VALVE 2 ON ON CLOSE OFF OFF OPEN ON GAS IGNITION

GAS VALVE STRUCTURE

DISASSEMBLY INSTRUCTIONS
Disassemble and repair the unit only after pulling out power plug from the outlet.
1. Remove 3 screws on the plate upper.
2. Push the top plate 3. Open the top plate
1. Remove 2 screw on the control panel frame.
2. Disconnect the connectors.
3. Pull the control panel assembly.
4. Remove 9 screws on the PWB(PCB)

assembly, display.

5. Remove 4 screws on the PWB(PCB)

assembly, main.

6. Disassemble the control panel assembly.
1. Open the top plate. 2. Open the control panel assembly. 3. Open the door assembly. 4. Remove 2 screws.
5. Remove 4 screws from upper side. 6. Disconnect the harness of door switch.
1. Open the top plate. 2. Remove Cover Cabinet. 3. Disconnect the door lamp and electro

sensor connector.

4. Remove 4 screws. 5. Disassemble the Tub Drum [Front].
1. Open the top plate. 2. Remove the Cover Cabinet and

Tub drum [front].

3. Disengage belt from motor and idler pulleys. 4. Carefully remove Drum out through front of dryer.
1. Open the door. 2. Remove the screw holding the drum lamp shield

in place.

3. Slide the shield up and remove. 4. Remove the bulb and replace with a 15 watt,
120 volt candelabra-base bulb.
5. Replace the lamp shield and screw.
1. Remove screw & exhaust duct.

PORTION A

2. Detach and remove the bottom, left or right side

knockout as desired.

3. Reconnect the new duct[11 in(28cm)] to the

DUCT TAPE

blower housing, and attach the duct to the base.
4. Pre-assemble 4" elbow with 4" duct.
Wrap duct tape around joint.
5. Insert duct assembly, elbow first, through the side
opening and connect the elbow to the dryer internal duct.
1. Remove the filter. 2. Remove 3 screws. 3. Pull the grill. 4. Disconnect electro sensor.
1. Open the top plate. 2. Remove the Cover Cabinet and Tub Drum [Front]. 3. Remove the Drum assembly. 4. Remove 2 screws and cover(Air guide). 5. Remove the bolt and washer. 6. Pull the fan. 7. Disconnect the motor clamp and motor.
1. Open the top plate. 2. Remove the Cover Cabinet and Tub Drum [Front]. 3. Remove the Drum assembly. 4. Remove 7 screws. 5. Pull the Tub Drum [Rear] towards the front.
1. Open the top plate. 2. Remove the Cover Cabinet. 3. Remove filter and 2 screws. 4. Pull the air duct towards the front.
1. Open the top plate. 2. Remove the Cover Cabinet and Tub Drum [Front]. 3. Remove the Drum assembly and Tub Drum [Rear]. 4. Disconnect Air duct from the Tub Drum [Front]. 5. Remove the roller from the Tub Drum [Front]

and Tub Drum [Rear].

EXPLODED VIEW
12-1. Control Panel & Plate Assembly
12-2. Cabinet & Door Assembly

A330 A600

12-3-1. Drum & Motor Assembly : Electric Type

F200 K400

K250 K310 K330 K221 K320 K340

K250 K550 K560 K610

F140 K510 K520 K640

F130 F110 K650

12-3-2. Drum & Motor Assembly : Gas type

K210 K250 K550 K560 K610

K510 M150 M160 M171 M170 M140 M110 M190 M180 M181 M230 M240 M220
M171 : Propane Gas orifice M170 : Natural Gas orifice

REPLACEMENT PARTS LIST

CAUTION : Before replacing any part of these components, read carefully the safety precautions in this manual. Note : S(Safety Parts), AL(Alternative parts)
L G M O D E L : T D - V 10050E, TD- V 10051E
S AL LOC A500 K610 K650 K640 K510 K520 K550 K560 K400 F200 K250 F110 F130 F140 A600 K100 K140 K120 K130 K210 K221 K250 K240 K320 K340 K330 K310 A390 A310 A330 A320 A400 A410 A460 A210 A110 A130 A120 A700 A800 DESCRIPTION CABINET ASSEMBLY MOTOR ASSEMBLY,WM PULLEY ASSEMBLY,MOTOR SWITCH,MICRO BLOWER ASSEMBLY HOUSING ASSEMBLY (MECH),BLOWER THERMISTOR ASSEMBLY THERMOSTAT ASSEMBLY TUB,DRUM[BACK] DUCT ASSEMBLY ROLLER ASSEMBLY HEATER ASSEMBLY THERMOSTAT ASSEMBLY THERMOSTAT ASSEMBLY HARNESS,PWB TUB ASSEMBLY,DRUM SEAL LIFTER BELT,POLY-V TUB,DRUM[FRONT] LAMP ASSEMBLY ROLLER ASSEMBLY DUCT ASSEMBLY COVER,GUIDE SENSOR GUIDE,FILTER FILTER ASSEMBLY,LINT FRAME ASSEMBLY COVER,CABINET SWITCH ASSEMBLY,DOOR LATCH ASSEMBLY DOOR ASSEMBLY LATCH,HOOK GASKET TOP PLATE ASSEMBLY PANEL,CONTROL PWB(PCB) ASSEMBLY,MAIN PWB(PCB) ASSEMBLY,DISPLAY RACK SIDE VENTING KIT MODEL P/N DLE5977W 3091EL0003A 4681EL1002A 4561EL3002A 3W40025D 5835EL1002A 3661EL1001C 6323EL2001B 6931EL3002A 3044EL0002B 5209EL1001C 4581EL3001A 5301EL1001E 6931EL3003D 6931EL3001E 6877EL1007A 3045EL1002C 4036EL3001A 4432EL1002B 4400EL2001A 3044EL1001A 6913EL3002C 4581EL3001A 5209EL1002A 3550EL1006B 6500EL3001A 4974EL1003B 5231EL1003B 3211EL1003A 3550EL0005A 6601EL3001A 4027EL1001A 3581EL0002A 4026EL3007A 4986EL2004A 3456ER0002D 3720EL0001A 6871EC1121A 6871EC1115A 3750EL1001B 383EEL9001B DLE3777W 3091EL0003A 4681EL1002A 4561EL3002A 3W40025D 5835EL1002A 3661EL1001C 6323EL2001B 6931EL3002A 3044EL0002B 5209EL1001C 4581EL3001A 5301EL1001E 6931EL3003D 6931EL3001E 6877EL1007A 3045EL1002C 4036EL3001A 4432EL1002B 4400EL2001A 3044EL1001A 6913EL3002C 4581EL3001A 5209EL1002A 3550EL1006B 6500EL3001A 4974EL1003B 5231EL1003B 3211EL1003A 3550EL0005A 6601EL3001A 4027EL1001A 3581EL0002D 4026EL3007A 4986EL2004A 3456ER0002E 3720EL0001A 6871EC1121E 6871EC1115C 3750EL1001B 383EEL9001B QTY 1 1

L G M O D E L : T D - V 10050G, TD- V 10051G
S AL LOC A500 K610 K650 K640 K510 K520 K550 K560 K400 F200 K250 M210 M230 M220 M240 M140 M150 M110 M190 M181 M170 M171 M180 M160 A600 K100 K140 K120 K130 K210 K221 K250 K240 K320 K340 K330 K310 A390 A310 A330 A320 A400 A410 A460 A210 A110 A130 A120 A700 A800 DESCRIPTION CABINET ASSEMBLY MOTOR ASSEMBLY,WM PULLEY ASSEMBLY,MOTOR SWITCH,MICRO BLOWER ASSEMBLY HOUSING ASSEMBLY (MECH),BLOWER THERMISTOR ASSEMBLY THERMOSTAT ASSEMBLY TUB,DRUM[BACK] DUCT ASSEMBLY ROLLER ASSEMBLY FUNNEL THERMOSTAT ASSEMBLY THERMOSTAT ASSEMBLY SENSOR ASSEMBLY GUIDE,BURNER PIPE ASSEMBLY VALVE ASSEMBLY,GAS PIPE ASSEMBLY SEAL ORIFICE(natural gas) ORIFICE(propane gas) CONNECTOR (MECH),PIPE IGNITER HARNESS,PWB TUB ASSEMBLY,DRUM SEAL LIFTER BELT,POLY-V TUB,DRUM[FRONT] LAMP ASSEMBLY ROLLER ASSEMBLY DUCT ASSEMBLY COVER,GUIDE SENSOR GUIDE,FILTER FILTER ASSEMBLY,LINT FRAME ASSEMBLY COVER,CABINET SWITCH ASSEMBLY,DOOR LATCH ASSEMBLY DOOR ASSEMBLY LATCH,HOOK GASKET TOP PLATE ASSEMBLY PANEL,CONTROL PWB(PCB) ASSEMBLY,MAIN PWB(PCB) ASSEMBLY,DISPLAY RACK SIDE VENTING KIT MODEL P/N DLG5988W 3091EL0003B 4681EL1002A 4561EL3002A 3W40025D 5835EL1002A 3661EL1001C 6323EL2001B 6931EL3002A 3044EL0002B 5209EL1001D 4581EL3001A 3016EL1001A 6931EL3003C 6931EL3004B 6501EL3001A 4974EL1001A 5201EL3001A 5221EL2002A 5201EL2001A 4036EL3002A 4948EL4001B 4948EL4002B 4932EL4001A 5318EL3001A 6877EL1008A 3045EL1002C 4036EL3001A 4432EL1002B 4400EL2001A 3044EL1001B 6913EL3002C 4581EL3001A 5209EL1002A 3550EL1006B 6500EL3001A 4974EL1003B 5231EL1003B 3211EL1003A 3550EL0005A 6601EL3001A 4027EL1001A 3581EL0002A 4026EL3007A 4986EL2004A 3457ER1006D 3720EL0001A 6871EC1121B 6871EC1115B 3750EL1001B 383EEL9001B DLG3788W 3091EL0003B 4681EL1002A 4561EL3002A 3W40025D 5835EL1002A 3661EL1001C 6323EL2001B 6931EL3002A 3044EL0002B 5209EL1001D 4581EL3001A 3016EL1001A 6931EL3003C 6931EL3004B 6501EL3001A 4974EL1001A 5201EL3001A 5221EL2002A 5201EL2001A 4036EL3002A 4948EL4001B 4948EL4002B 4932EL4001A 5318EL3001A 6877EL1008A 3045EL1002C 4036EL3001A 4432EL1002B 4400EL2001A 3044EL1001B 6913EL3002C 4581EL3001A 5209EL1002A 3550EL1006B 6500EL3001A 4974EL1003B 5231EL1003B 3211EL1003A 3550EL0005A 6601EL3001A 4027EL1001A 3581EL0002D 4026EL3007A 4986EL2004A 3457ER1006E 3720EL0001A 6871EC1121F 6871EC1115D 3750EL1001B 383EEL9001B QTY 1 1

Clothes Dryers Qualified Models List

Updated: 05/09/2011

Models Listed Change Often. Visit www.conservationrebates.com for the most up-to-date list.
BRAND Admiral Amana Amana Amana Amana Amana Asko Asko Asko Asko Bosch Bosch Bosch Bosch Bosch Bosch Bosch Bosch Bosch Crosley Crosley Crosley Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Estate Estate Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire MODEL AGD4475TQ Amana NGD4800VQ Enlighten NDG6800AWW NGD4500VQ NGD5100TQ NGD7300WW TL751GW TL751GXXL(Ultra Care Series) TL751GXXLPP TL751GXXLW WTVC4500UC WTMC3521 WTMC4521UC WTMC553 WTMC652SUC WTMC8530 WTVC4500UC WTVC553AUC WTVC6530UC CDG500F CDG8000GR CDG8000GWC EIGD55H* EIGD55HMB EIGD55IRR EIMGD55IIW EWGD65HSS EWGD65IMB EWMGD65H* EWMGD65HSS EWMGD65IRR EGD4100SQ EGD4400WQ DG08 DG27 DG60F27AW2 DG60FA1 DG62T27GW1 DG62TG1 DGGX2 AGQ6000ES AGQ7000EE AGQ7000ES AGQ8000FS AGQB6000E FAQG7011* FAQG7017K* FAQG7072L* FAQG7077K* FASG7074LW BRAND Amana Amana Amana Amana Amana Asko Asko Asko Asko Asko Bosch Bosch Bosch Bosch Bosch Bosch Bosch Bosch Bosch Crosley Crosley Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Electrolux Estate Estate Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Fisher & Paykel Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire MODEL Amana NGD4500VQ Amana NGD5100TQ NDG6800AWW NGD4800VQ NGD7200TW TL751G* TL751GXXL TL751GXXLBB TL751GXXLRR TL751XXL WTMC1501 WTMC352SUC WTMC552 WTMC6521UC WTMC852 WTVC3500UC WTVC5530UC WTVC553SUS WTVC8530UC CDG8000GBL CDG8000GS EIED55IKG EIGD55HIW EIGD55IKG EIMGD55I* EIMGD55IMB EWGD65HTS EWMGD651MB EWMGD65HIW EWMGD65HTS EWMGD70J** EGD4400SQ EGD5600GWW DG09 DG27CW1 DG60F27EW1 DG62T27DW1 DG62TD1 DGGX1 DGIX2 AGQ6700FS AGQ7000EG AGQ8000F AGQ8700F AGQB6400F FAQG7011K* FAQG7021LW FAQG7073K* FASG7073L* FGQ1442*

Page 1 of 6

BRAND Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric MODEL FGQ1442E FGQ1452 FGQ1452HS FGQ332E FGQ5000H FRG5711KW GLGH1642DS GLGQ2152ES GLGQ217OKS GLGR1042FS GLGR341A GLGR642A LAQG7077K LGQ1442ES LGQ2152EE LGQ332DSO LGQ6400FSO DBLR333GECC DBLR333GGCC DBSR453GBW DBVH510G DBVH510GHW DBVH520GJ DBXR463GDCC DBXR463GGW DCVH640GJ DCVH660GHW DHDSR46GG DHDVH66GHB DJXR433GCW DLSR483GGW DPGT650GHM DPGT750GCPL DPSB619GDCC DPSE810GGW DPSR610GGW DPVH890EJ DRSR483GG* DRSR483GGW DRSR495GGWW DSXH43GFWW DSXH47G DVLR223GEW DVLR223GGW* DWSR463GGW DWSR483BCC DWSR483GG* DWXR463GGW DWXR483GBW GFDN110GL* BRAND Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire Frigidaire General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric General Electric Page 2 of 6 MODEL FGQ1442FE FGQ1452HE FGQ321AS FGQ332ES* FGQB215 FRG5714KW GLGQ2152EE GLGQ217OKE GLGQ942CS GLGR104FS GLGR341CC LAQG7011* LAQG8000LW LGQ1452* LGQ2152H LGQ6000E DBLR333G* DBLR333GEW DBLR333GGW DBSR463GGWW DBVH510G* DBVH512GFW DBVH520GJWW DBXR463GDW DCVH515GF DCVH660GHBB DCVH680GJ* DHDVH52GF DJXR433GCCC DLSR483GEW DLSR495GGW DPGT750GC* DPGT750GCWW DPSB620GC DPSE810GGWT DPVH880GJ* DPVH890GJ* DRSR483GGC DRSR495GGW DRSR610GGWT DSXH46GF DSXH47G* DVLR223GGW DWSR405GBW DWSR463GGW* DWSR483GBW DWSR483GGW DWXR463GGW* GFDN100GLWW GFDN240GL*

BRAND Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Miele Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Siemens Speed Queen Speed Queen Staber Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool MODEL MGD9700A MGD9700SQ MGD9800T MGDB400VQ MGDB800V* MGDB850W* MGDC400VW MGDC700V* MGDE250XL MGDE400XR MGDE500V* MGDE900V* MGDX550XW MGDZ400TQ MGDZ600TW* PYE4500AY T9822 DV209 DV218AG* DV220AG* DV306LGW DV328AGR DV330AG* DV337AG DV339AGW DV407AWG DV410AG* DV419AGU DV438 DV520AG* WTXD5522UC AGS28AWF CGS68AFW HXD2304G GGW9250P GGW9250S GGW9260PW LGQ9508PW LGR8648PW WGD5100 WGD5300 WGD5321SQ WGD5500X* WGD5521SQ WGD5590SQ WGD5600V* WGD5700S WGD5700X* WGD5800S WGD5820SW BRAND Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Maytag Miele Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Siemens Speed Queen Speed Queen Speed Queen Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Page 5 of 6 MODEL MGD9700SB MGD9800AWQ MGDB200VQ MGDB700VQ* MGDB800VQ MGDC300XW MGDC500VW MGDE200XW MGDE300V* MGDE400XW MGDE500W* MGDX500X* MGDX600XW MGDZ600T* MLG2000AWW* T9820 DV203AGW DV210AGW DV219AGW DV2C6BGW DV328AG* DV328AGW DV331AG* DV338AG DV350AG* DV409AG* DV419AGE DV419AGW DV448AG* WTXD5521UC ADG4BF AGS68AWF KGS18AFW GGW9200 GGW9250PT GGW9260PL GGW9868KQ LGR8648PG WGD4900XW WGD5200VQ WGD5320SQ WGD5500S* WGD5520S2 WGD5550XW WGD5600S WGD5600X* WGD5700V* WGD5790 WGD5810SW WGD5821SW
BRAND Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool MODEL WGD5900S WGD6400SB WGD6400SW WGD6600WL WGD7400XW WGD7800XW WGD8300SR WGD8410SW WGD8500SW WGD9150WW WGD9250W* WGD9300V WGD9450 WGD94HEX* WGD9550W WGD9600T WGD9750 Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool Whirlpool BRAND MODEL WGD6200SW WGD6400SG WGD6600V WGD7300XW WGD7600XW WGD8300S* WGD8300SW WGD8500SR WGD9050XW WGD9200SQ WGD9270X* WGD9400S* WGD9470W* WGD9500TW WGD95HEX* WGD9600TW WGD97HEX*
Asterisks (*) indicate that a coding variable may be used in place of the asterisks to indicate a color or feature that does not affect washer efficiency.

Page 6 of 6