LGEAP_MCD112_ENG_MFL40387019

ENGLISH

MODEL : MCD112 MCD112B MCD212
As an ENERGY STAR Partner, LG has determined that this product or product models meet the ENERGY STAR guidelines for energy efficiency. ENERGY STAR is a U.S. registered mark.
There is so much your Hi-Fi system can do
Record from a CD, AUX, USB or radio to cassette Go to page 8

Contents

Setting up About Player About Remote control Listening to CDs Connecting your portable USB player - OPTIONAL Listening to the radio Listen to cassette tapes Recording USER EQ Setting the Clock Use your player as an alarm clock About MP3/WMA Safety Precaution Troubleshooting Specifications 11
Lull me to sleep and wake me up Go to page 9 Play CDs and cassettes Go to pages 6 & 7
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
2 MINI Hi-Fi SYSTEM ] USER GUIDE

Setting up

Put the batteries in the remote control Make sure that the + (plus) and - (minus) on the batteries match those on the remote control.
1 Connect the speaker cables to the player
Cables from the left-hand speaker connect to the terminal marked L (left) + (plus) and - (minus). Cables from the right-hand speaker are connected to the terminal marked R (right) + (plus) and - (minus). To connect the cable to the player, press each of the four square plastic finger pads on the rear of the player. The connector will open ready to receive the cable.
2 Fit the AM loop aerial to its stand Connect the AM loop aerial to the player.
3 Connect the FM aerial The reception will be at its best when the two loose ends of the aerial are in a straight line and horizontal. 4 Plug the power plug into a wall socket
MINI Hi-Fi SYSTEM ] USER GUIDE

About Player

POWER You can set up the unit into an economic power save mode. In the power-on status, press and hold 1/] (POWER) for about 3 seconds. To cancel power save mode, press 1/] (POWER).

CD tray

ST./MONO Press ST./MONO. This will change the tuner from stereo to mono and usually improve the reception.
XTS - PRO This function creates the optimum sound for you to play the original sound. Each time you press XTS - PRO, XTS -- PRO ON or XTS -- PRO OFF is displayed in turn. (The XTS Pro function will not be operated when a headphone has been connected.) D.SKIP If more than one portable USB player is connected to the system at the same time, press D.SKIP to select one of them. AUX You can connect many other types of audio or audio visual device to the system via the auxiliary sockets (AUX IN) on the back of the player. VOLUME Control the volume when using any function. USB connector - OPTIONAL Connect a remote USB compatible player here.

MP3 OPT. (MP3 Optimizer)

This function is optimized for compressible MP3 files so that it improves the bass sound.
Press DEMO in power off state to demonstrate the functions on the display win] dow. To cancel it, press 1 /] or DEMO again.

Headphone jack

Connect a headphone plug ( 3.5 mm) into the jack to listen to the sound through headphones (not supplied).

About the Remote control

Search for a folder of MP3/WMA files When a CD containing MP3/WMA files in several folders is being played, press PRESET/FOLDER to select the folder you want to play. Fall asleep while listening to your player Firstly, select a radio station or music. Press SLEEP on the remote one or more times to select a delay of between 10 and 180 minutes, after which the player will turn off. Use when playing a CD Listen to your tracks again and again Press REPEAT once to repeat the track currently playing. Press REPEAT twice to repeat the whole CD, or if youre listening to the whole folder of MP3/WMA CD. The display will show what is being repeated. Use when playing a cassette tape Sound quality adjustment You can select a desired sound mode by using EQ. Play any track on a CD Press the corresponding number buttons on the remote control. Temporarily stop the sound Press the button again to return to the sound.
To change the functions Change the functions between FM, AM, CD, AUX, USB or TAPE. Dim the display light For storing radio stations If you have saved radio stations using PROGRAM/MEMO, you can scroll through them and select one. (see Listening to the radio)
eXtreme Dynamic Sound System Reinforce the treble, bass and surround sound effect. XDSS ON will show in the display. Press again for XDSS OFF. RANDOM Press RANDOM, you can play tracks/files in a random order or cancel it. See information about your music MP3/WMA files often come with tags. The tag gives the Title, Artist or Album. Press INFO while a file is playing to see this information. If there are no tags, NO ID3 TAG or NO WMA TAG will show. MINI Hi-Fi SYSTEM ] USER GUIDE 5

Listening to CDs

ON PLAYER
1. Open the CD drawer: 2. Select the CD tray : 3. Insert the CD : Label facing up. 4. Close the CD drawer: The display will show the total number of tracks (files). 5. Select the CD function: 6. Start the CD playing: 7. To stop a CD playing: Z OP./CL. D.SKIP

ON REMOTE

D.SKIP
Connecting your portable USB player - OPTIONAL
The advantage of connecting your portable USB player through the systems USB port is that the portable device can be controlled from the system. Connect the portable player to the system using a USB cable (not supplied).

ON PLAYER ON REMOTE

USB 1. Press: 2. The display will show CHECKING, followed by the number of files displayed. 3. Press: 4. Alternatively a numbered track can be played by using the numbers on the remote control. 5. Before disconnecting the portable USB player, change to any other function by pressing: 6. Remove the USB cable. USB

Z OP./CL.

CD B x STOP
FUNCTION B/[] x (CD STOP)

Pause or restart a CD

Press CD[] on the front panel or B/[] on the remote control during playback. Press this button again to resume play.
Search for a section within a track
Hold.bb/BB> during playback, then release at the point you want. (This function is only available for Audio CDs.)

CD, TUNER, TAPE or AUX

FUNCTION

Skip to another track

Press.bb/BB> on either the player or the remote control. Listen to your tracks in any order Up to 20 tracks on a CD can be listened to in the order of your choice. Insert a CD and wait for it to be read. Press PROGRAM/MEMO, then use.bb/BB> to select the track. Press PROGRAM/MEMO again to save and select the next track. Press B or B/[]. To clear your selection, press STOP, PROGRAM/MEMO, STOP. NOTE : You can choose a desired CD by using D.SKIP.
NOTE : Some portable devices are not compatible with this system.

Listening to the radio

Make sure both the FM and AM aerials are connected.
1. Select either AM or FM: 2. Select the radio station: 3. To save a radio station: A preset number will show in the display. 4. To select a saved station: Up to 50 radio stations can be saved. 5. To confirm press: TUNER TUNING (-) or TUNING (+)
Choose a preset number for a radio station When storing a radio station, the preset number can be chosen. When the player automatically shows a preset number press PRESET/FOLDER then. Press PROGRAM/MEMO to save the number.
Delete all the saved stations ON REMOTE
FUNCTION TUN.-/ TUN.+ PROGRAM/MEMO Press and hold PROGRAM/MEMO for two seconds. ERASE ALL shows. Press PROGRAM/MEMO to erase all the saved stations.

Listen to cassette tapes

1. Open the tape door : 2. Insert the tape : 3. Close the tape door : 4. Select the TAPE function : 5. Start the tape playing : 6. To stop a tape playing:

PRESET(-) or PRESET(+)

PRESET/FOLDER

PROGRAM/MEMO

TAPE B x STOP

FUNCTION B x (TAPE STOP)

See information about your radio stations - OPTIONAL

The FM tuner is supplied with the Radio Data System (RDS) facility. This shows the letters RDS on the display, plus information about the radio station being listened to. Press RDS several times to view the information. PTY - Programme Type, such as News, Sport, Jazz Music. RT - Radio Text, the name of the radio station. CT - Time Control, the time at the location of the radio station. PS - Programme Service name, the name of channel. You can search the radio stations by programme type by pressing RDS. The display will show the last PTY in use. Press PRESET(-) / PRESET(+) one or more times to select your preferred programme type. Press and hold TUNING (-) / TUNING (+). The tuner will search automatically. When a station is found the search will stop.
To Play Fast backward or Forward
After pressing bb/BB on the remote control or.bb/BB> on the front panel during playback, or stop, press B at a point you want.

Dubbing

This function shows how to record from tape to tape. Press TAPE (or FUNCTION) to select tape function. TAPE 1 - Insert a playback tape to dub. TAPE 2 - Insert a blank tape. Press DUBB as shown below. To stop dubbing, press x.
Look for radio stations automatically
Press TUNING (-) / TUNING (+) on the front panel for more than 0.5 second. Or press TUN.- / TUN.+ on the remote control for more than 0.5 second. The tuner will scan automatically and stop when it finds a radio station. MINI Hi-Fi SYSTEM ] USER GUIDE 7

Recording

Record from a CD, AUX, USB or radio to cassette
Wind the tape to the point where you want the recording to start. Use only normal tapes.

USER EQ

You can listen to music with the desired sound effect (BASS, MIDDLE and TREBLE).
1. Select a USER EQ: 2. When USER EQ is displayed, press : 3. Select the sound effect you want among BASS, MIDDLE or TREBLE : 4. Adjust sound level (MIN, -4 to +4, MAX) : 5. Repeat the steps from 2 to 3 to set other sound effect : 6. Press : EQ. SET PRESET (-) or PRESET (+).bb/BB>
1. Open the TAPE 2 door : 2. Insert a blank tape : 3. Close the TAPE 2 door : 4. Select a mode (FM, AM, CD, USB or AUX) in which you want to record : - Start playing the source you want to record. 5. Puts the unit in standby more for recording: 6. Start the Recording : 7. To stop a Recording : Z PUSH EJECT
CD, TUNER, USB, TAPE or AUX

REC REC x STOP

z/[] z/[] x

Setting the Clock

1. Press for at least 2 seconds: 2. Choose from either: AM 12:00 (for an am and pm display) or 0:00 (for a 24 hour display). 3. Confirm your selection: 4. Select the hours: 5. Press: 6. Select the minutes: 7. Press: CLOCK.bb/BB>
CD to Tape Synchronized Recording

The CD synchro recording function dubs a complete CD and programmed titles automatically into a cassette.
1. Select the CD function : 2. Start the Recording : The synchronized recording is started automatically after about 7 seconds. 3. To stop Recording : CD CD SYNC.
SET.bb/BB> SET.bb/BB> SET

x STOP

Use your player as an alarm clock
Press and hold TIMER for two seconds. Each function, TUNER, CD, USB, TAPE flashes for two seconds. Press SET when the function you want to be woken by is showing. If you choose TUNER, PLAY and REC flash, PLAY and REC. Choose one of them. If you choose TUNER and PLAY you will be shown the stations you have saved as presets. Use TUNING (-) or TUNING (+) to select the station you want, then press SET. You will be shown the ON TIME display. This is where you set the time you want the alarm to go off. Use TUNING (-) or TUNING (+) to change the hours and minutes and SET to save. You will then be shown the OFF TIME display. This is where you set the time you want the function to stop. Use TUNING (-) or TUNING (+) to change the hours and minutes and press SET to save. Next you will be shown the volume (VOL) you want to be woken by. Use TUNING (-) or TUNING (+) to change the volume and SET to save. Switch the system off. The red (clock icon) shows that the alarm is set. When the system is turned off you can check the time the alarm is set for by pressing TIMER. You can also turn the alarm on and off by pressing TIMER. To set the alarm to go off at a different time, switch the system on and re programme following the same steps as initially.

About MP3/WMA

MP3/WMA Disc compatibility with this unit is limited as follows: Sampling Frequency 8 - 48 kHz (MP3), 32 - 48 kHz (WMA) Bit rate 8 - 320 kbps (MP3), 48 - 320 kbps (WMA) CD-R physical format should be ISO 9660 If you record MP3/WMA files using the software which cannot create a FILE SYSTEM, for example Direct-CD etc., it is impossible to playback MP3 files. We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system. File names should be named using 30 letters or less and must incorporate.mp3,.wma extension e.g. ********.MP3 or ********.WMA Do not use special letters such as / : * ? < >etc. Even if the total number of files on the disc is more than 1000, it will only be shown up to 999.

Safety Precaution

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an LG Authorised Service Centre. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction has been adhered to.
The appliance is not intended for use by young children or infirm persons without supervision. Young Children should be supervised to ensure that they do not play with appliance. If the appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.

CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owners manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service centre. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

Troubleshooting

Symptom

No power. No sound.

Specifications

Cause Correction

General Net Weight 5.57 kg (MCD212) 5.36 kg (MCD112/MCD112B) External dimensions (WxHxD) 270 x 310 x 390 mm Tuner FM Tuning Range AM Tuning Range Amplifier Output Power T.H.D Frequency Response Signal-to-noise ratio CD Frequency response Signal-to-noise ratio Dynamic range 87.5 - 108.0 MHz or 65 - 74 MHz, 87.5 - 108.0 MHz 522 - 1620 kHz or 520 - 1720 kHz 100W + 100 W (MCD212) 50W + 50 W (MCD112/MCD112B) 0.5 % 40 - 20000 Hz 75 dB 40 - 20000 Hz 75 dB 75 dB Bass Reflex 2 Way 2 Speaker W 200 W 220 x 326 x 272 mm 3.25kg Bass Reflex 2 Way 2 Speaker W 100 W 200 x 326 x 228 mm 2.92 kg
The unit does not start playback.
The remote control does not work properly.

Unable to record.

Plug the power cord into the wall outlet securely. The power of the external source Switch on the external source equipment. equipment is turned off. Set the speaker cable to the The speaker cable is connected correct position, then turn on the to a wrong position. unit again by pressing POWER. Insert a playable disc. An unplayable disc is inserted. Place the disc with the playback The disc is placed upside down. side down. Place the disc on the disc tray The disc is not placed within the correctly inside the guide. guide. Clean the disc. The disc is dirty. The remote control is not pointed Point the remote control at the remote sensor of the unit. at the remote sensor of the unit. The remote control is too far from Operate the remote control within about 23 ft (7 m). the unit. Remove the obstacle. There is an obstacle in the path of the remote control and the unit. Replace the batteries with new The batteries in the remote conones. trol are exhausted. Record protect tabs are removed. Cover holes on back edge of tape with tap. The power cord is disconnected.
Speakers MCS212F Type Impedance Rated Input Power Max. Input Power Net Dimensions (WxHxD) Net Weight (1EA) MCS112F Type Impedance Rated Input Power Max. Input Power Net Dimensions (WxHxD) Net Weight (1EA)
Designs and specifications are subject to change without notice. MINI Hi-Fi SYSTEM ] USER GUIDE 11

P/NO : MFL40387019