LG WD-1274FBN Manual
LG WD-1274FBN Washing Machine, size: 7.2 MB
Here you can find all about LG WD-1274FBN like manual and other informations. For example: review.
LG WD-1274FBN manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a LG WD-1274FBN please write about it to help other people. [ Report abuse or wrong photo | Share your LG WD-1274FBN photo ]
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
WD-1374(6)F(H)B WD-1274(6)F(H)B WD-1174(6)F(H)B WD-1074(6)F(H)B WD-8074F(H)B
LGs jumbo drum can wash about 40% more load than conventional washing machines. A bigger drum improves the wash performance.
More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.
The Child-Lock system has been used to prevent children from pressing any button to change the program during operation.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level.
If the washing machine is turned off by a power failure, it will restart automatically from the position it stopped at adjusting accordingly.
Warnings....30 Specification...31 Installation...32 Care before washing...37 Adding detergent...38 Function...39 How to use washer...40 Maintenance...47 Troubleshooting guide...50
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following: Do not install or store the washer where it will be exposed to the weather. Do not tamper with controls. Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out. Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc. Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance. Do not leave the washer door open. An open door could entice children to hang on the door or crawl inside the washer. Never reach into washer while it is moving. Wait until the drum has completely stopped. The laundry process can reduce the flame retardant of fabrics. Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may ignite or explode. To avoid such a result, carefully follow the garment manufacturers wash and care instructions. Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer. To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning. Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
SAVE THESE INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance. Do not use an adapter or otherwise defeat the grounding plug. If you dont have the proper outlet, consult an electrician.
n BS Plug Safety Details (For U.K. User)
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE
This appliance must be earthed
Green and Yellow(Earth) Brown(Live) Blue(Neutral)
Fuse Cord grip
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol ( ) or coloured Green or Green and Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
n Electrical connection
1. Do not use an extension cord or double adapter. 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
n Washing Machine is to be connected to the water mains using new hosesets and that old hose-sets should not be used. n Connecting water supply hose
Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm2) Dont strip or crossthread when connecting Inlet hose to the valve. If the water supply pressure is more than 1000kPa, a decompression device should be installed. Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks.
Hose connector Rubber seal
Check water tightness of washing machine connections by turning the tap completely on. Periodically check the condition of the hose and replace the hose if necessary.
Make sure that there is no kink on the hose and that it is not crushed. When your washer has two valves,
Hot water tap Cold water tap
The Inlet hose which has red connector is for the hot water tap. If the washer has two valves, the energy is saved by using hot valve.
n Installation of drain hose
ca. 100 cm
ca. 145 cm
max. 100 cm
min. 60 cm
ca. 105 cm
When installing the drain hose sink, secure it tightly with a string. Proper securing the drain hose will protect the floor from damage due to water leakage.
Hose Retainer Tie strap
max. 100cm min. 60cm
The drain hose should not be placed higher than 100 cm above the floor. Proper securing the drain hose will protect the floor from damage due to water leakage. When the drain hose is too long, please dont fill into the washer. This will cause abnormal noise.
n Level adjustment
1. Adjustable the washing machine properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.
Adjustable feet Higher Lower
2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level)
Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
are before washing
n Caring before washing
1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one. Soil (Heavy, Normal, Light) Color (White, Lights, Darks) Lint (Lint producers, Collectors) Separate clothes according to amount of soil. Separate white fabrics from colored fabrics. Wash lint producers and lint collectors separately.
Pre Wash Eco Less than Rinse+ 4.0 kg Bio Rinse+ Less than 3.0 kg Less than 2.0 kg Less than 2.0 kg
Delicate Delicate laundry easily damaged (silk, curtains.) Wool
Machine washable 30C woolens with pure (40C, Cold) new wool only Hand Wash marked delicate and Cold(30C, 40C) wool laundry
Pre Wash : If the laundry is heavily soiled, Pre Wash course is effective. Pre Wash is available in Coloureds, Whites and Synthetic Program. Eco : By selecting Eco function, the water temperature is reduced and washing time is lengthened. So you can economize in your consumption of energy. Rinse+ : If you wish to rinse more, the Rinse+ function will remove any trace of detergents. Bio : If you want to elimenate protein stains (milk, blood, chocolate.), you may select Bio function by pressing the option button. You can select Bio function and Eco function when temperature is higher than 60C in Whites, Coloureds and Synthetic.
H ow to use washer
1. For use in the initial programme (Coloureds)
Press the Power button to start. Press the Start/Pause button. Initial condition - Wash : Only main wash - Rinse : 3 times - Spin : 800 rpm - Water temperature : 40C - Program : Coloureds
2. Manual Selecting
Press the Power button to start. Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page41~page45 Press the Start/Pause button.
(1) Button : Option (2) Button : Spin (3) Button : Temp.
(4) Child Lock (5) Button : Time Delay (6) Button : Rapid
(7) Button : Start/Pause (8) Dial : Program (9) Button : Power
By pressing the Option button, the Option function can be selected. - Bio - Rinse+ - Eco - Pre Wash
By selecting Eco function, the water temperature is reduced and washing time is lengthened. So you can economize in your consumption of energy. [You can select Eco function when temperature is higher than 60 C in Whites, Coloureds and Synthetic.]
If you want to elimenate protein stains(milk, blood, chocolate.), you may select Bio function by pressing the option button. [You can select Bio function when temperature is higher than 60 C in Whites, Coloureds and Synthetic.]
4. Pre Wash
If the laundry is heavily soiled, Pre Wash course is effective. Pre Wash is available in Whites, Coloureds and Synthetic. If lamp turns on, that function has been selected.
If you wish to rinse more, Rinse+ function will remove any trace of detergents. By selecting Rinse+ function, the Rinse Time and the Rinse water are increased.
WD-1074(6)F(H)B - Whites / Coloureds/Synthetic 800U 1000U Rinse HoldU No SpinU 400U 600 - Delicate 400U 600U 800U Rinse HoldU No Spin - Wool / Hand Wash 400U 600U 800U 1000U Rinse HoldU No Spin WD-1174(6)F(H)B - Whites / Coloureds/Synthetic 800U 1100U Rinse HoldU No SpinU 400U 600 - Delicate 400U 600U 800U Rinse HoldU No Spin - Wool / Hand Wash 400U 600U 800U 1100U Rinse HoldU No Spin WD-1274(6)F(H)B - Whites / Coloureds 800U 1000U 1200U Rinse HoldU No SpinU 400U 600 - Synthetic 800U 1000U Rinse HoldU No SpinU 400U 600 - Delicate 400U 600U 800U Rinse HoldU No Spin - Wool / Hand Wash 400U 600U 800U 1000U Rinse HoldU No Spin
By pressing the Spin button, the spin speed can be chosen.
1. Spin selection
Spin speed is available according to the program as follows. WD-8074F(H)B - Whites / Coloureds / Synthetic 800U Rinse HoldU No SpinU 400U 600 - Delicate / Wool / Hand Wash 400U 600U 800U Rinse HoldU No Spin
WD-1374(6)F(H)B - Whites / Coloureds 800U 1100U 1300U Rinse HoldU No SpinU 400U 600 - Synthetic 800U 1100U Rinse HoldU No SpinU 400U 600 - Delicate 400U 600U 800U Rinse HoldU No Spin - Wool / Hand Wash 400U 600U 800U 1100U Rinse HoldU No Spin By pressing the Temp button, the water temperature can be selected. - Cold - 30C / 40C / 50C / 60C / 95C
1. Water Temperature
Water temperature can be selected as below according to the program. - Whites 95C U 40C U 50C U 60C - Coloureds & Synthetic 40C U 50C U 60C U Cold U 30C - Delicate & Wool 30C U 40C U Cold - Hand Wash Cold U 30C U 40C Selected temperatures lamp turns on. For the more detailed information, please refer to the page39.
2. No spin
If no spin is selected, the washer stops after draining water. If lamp turns on, that function has been selected.
3. Rinse Hold
If you desire to leave fabrics in the machine without spinning after rinse to prevent them from getting wrinkled, you may select rinse hold by pressing the spin button. If you want to drain and spin, when Rinse Hold function is proceed, press the Start/Pause button to cancel the Rinse Hold function and select spin speed or program. press the Start/Pause button again to start program. If you want to drain only, select the no spin or pump program. If lamp turns on, that function has been selected.
Child Lock Time Delay
If you want to lock all the buttons to prevent operation by a child or infirm persons, this function can be used.
1. Time Delay
Preparing washing before starting Time Delay - Turn on the water tap. - Load laundry and close the door. - Place the detergent and fabric softener in the drawer. How to set Time Delay - Press Power button. - Turn the Program dial to select the program you require. - Press Time Delay button and set the desired time. - Press the Start/Pause button. (: blinks.) If Time Delay button is pressed, 3:00 is displayed. The maximum delayed time is 19:00 hours and the minimum time is 3:00 hours. Each pressing of the button advances on time delay by one hour. To cancel the time delay, press the Power button. Time Delay is expected time from the present to the completion of washing cycle or selected process (Wash, Rinse, Spin). According to the condition of water supply and temperature, the delayed time and the actual washing time may vary.
1. Child Lock
Child Lock can be set by pressing the Temp. button and Time Delay button simultaneously.
When child lock is set, all buttons are inoperable. To deactivate Child Lock system, press Temp. and Time Delay button simultaneously again.
If you want to change the program when Child Lock is active, 1. Press both Temp. and Time Delay together. 2. Press the Start/Pause button. 3. Change the desired program and press the Start/Pause button.
Change the desired program
The child lock can be set at any time and it is automatically canceled when operational errors occur. Also Child Lock works when power is off.
By pressing the Rapid button, Rapid function is selected.
Rapid function reduces the whole time including the washing and rinsing time about by half an hour. Rapid is available in Whites, Coloureds program. If lamp turns on, that function has been selected.
This Start/Pause button is used to start wash cycle or pause the cycles.
If temporary stop of wash cycle is needed, press the Start/Pause button. After the pause button is pressed, the power is turned off automatically 4 minutes later.
9 programs are available according to the laundry type.
Press the Power button to turn power on and off To cancel the Time Delay function, it can also be used.
When Start/Pause button is pressed, Coloureds program is automatically selected. - By turning the Program dial, the program is selected in orders of Coloureds U Synthetic U Delicate U Wool U Hand WashU Rinse+Spin U Spin U PumpU Whites. Regarding to the laundry type for each program Please refer to the page39.
2. Initial Program
When the Power button is pressed, the washer is ready for Coloureds program. And the other initial conditions as follows. So, if you want to advance into the washing cycle without selecting the program, just press the Start/Pause button and then the washer will proceed. Initial program - Coloureds Program / Main wash / Normal Rinse/800 rpm / 40C 45
- Whites - Coloureds - Synthetic - Delicate - Wool - Hand Wash - Rinse+Spin - Spin - Pump
3. Completion of washing
When washing cycle is completed, is displayed on the Multi display.
1. Special function display
When child lock is selected, the is displayed. When time delay is selected, it shows the remaining times to finish the selected program.
4. Time left
During washing cycle, the remaining washing time is displayed. Recommended program by manufacturer. - Whites : around 2 hours and 38 minutes - Coloureds : around 1 hour and 55 minutes - Synthetic : around 1 hour and 28 minutes - Delicate : around 58 minutes - Wool : around 58 minutes - Hand Wash : around 57 minutes - Rinse+ Spin : around 19 minutes - Spin : around 11 minutes - Pump : around 1 minute The washing time may vary by the amount of laundry, water pressure, water temperature and other washing conditions. If the imbalance is detected or if the suds removing program works, the wash time shall be longer. (Max. increasing time is 45minutes.)
2. Self diagnose display
If the washer has a trouble, the trouble type is displayed. : Sensing water pressure error : Problem of overfilling water : Door is not closed : Over load in moter. : Over load in moter. : Water inlet trouble : Drainage trouble : Imbalance trouble : Water temperature trouble If this error letters are displayed, please refer to the troubleshooting page50 and follow the guide.
Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards.
n The water inlet filter
-" " error message will blink on the control panel when water does not enter the detergent drawer. - If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time.
1. Turn off the water tap.
2. Unscrew the water inlet hose. 4. Tighten up the inlet hose.
3. Clean the filter using a hard bristle brush.
n The drain pump filter
The drain filter collects threads and small objects left in the laundry. Check regularly that the filter is clean to ensure smooth running of your machine. ! CAUTION
First drain it using the drain hose and then open the pump filter to remove whatever may have stopped it up. Be careful when draining if the water is hot.
2. Unplug the drain plug ( ), allowing the water to flow out. At this time use a vessel to prevent water flowing on to the floor. If the water does not flow any more, turn the pump filter ( ) open to the left. 3. Take out any foreign material from the pump filter ( ). After cleaning, turn the pump filter ( ) clockwise and insert the drain plug ( )to the original place. close the lower cover cap.
1. Open the lower cover cap ( ) by using coin. Turn the drain plug ( ) to pull out the hose.
n Dispenser drawer
After a while detergents and fabric softeners leave a deposit in the drawer. It should be cleaned from time to time with a jet of running water. If necessary it can be removed completely from the machine by pressing the catch downward and by pulling it out. To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
n The drawer recess
Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush. Once you have finished cleaning, replace the drawer and run a rinse cycle without laundry.
n The washing drum
If you live in a hard water area, limescale continuously builds up in places where it cannot be seen and it is not easily removed. Over time the build up of scale clogs appliances, and if it is not kept in check these will eventually have to be replaced. Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal articles (paper clips, safety pins) which have been left in the drum. The washing drum should be cleaned from time to time. If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use. Descaler could contain components that can attack part of your washing machine. Remove the spots with a stainless steel cleaning agent. Never use steel wool.
n Cleaning your washer
1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. IMPORTANT: Do not use methylated spirit, diluents or similar products. 2. Interior Dry around the washer door opening, flexible gasket and door glass. These areas should always be clean to ensure a water tight seal. Run washer through a complete cycle using hot water. Repeat process if necessary.
Remove hard water deposits using only cleaners labeled as washer safe.
n Winterizing instructions
If the washer is stored in an area where freezing can occur or moved in freezing temperatures, follow these winterizing instructions to prevent damage to the washer: 1. Turn off water supply tap. 2. Disconnect hoses from water supply and drain water from hoses. 3. Plug electrical cord into a properly grounded electrical outlet. 4. Add 1gallon(3.8L) nontoxic recreational vehicle(RV) antifreeze to empty wash drum. Close door. 5. Set spin cycle and let washer spin for 1minute to drain out all water. Not all of the RV antifreeze will be expelled. 6. Unplug electrical power cord, dry drum interior, and close door. 7. Remove dispenser drawer. Drain any water in compartments and dry compartments. Replace drawer. 8. Store washer in an uprignt position. 9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent. Do not add wash load.
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you call the Service Department.
Rattling and clanking noise
Foreign objects such as coins or safety pins maybe in drum or pump.
Stop washer and check drum and drain filter. If noise continues after washer is restarted, call your authorized service. If sound continues, washer is probably out of balance. Stop and redistribute wash load. If not removed during installation. See Installation for removing transit bolts. Wash load unevenly distributed in drum. Stop washer and rearrange wash load. Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary. Too much detergent or unsuitable detergent? The formation of foam can cause water leaks.
Heavy wash loads may produce a thumping sound. This is usually normal. Have all the transit bolts and packing been removed? Are all the feet resting firmly on the ground?
Fill hoses or drain hose is loose at tap or washer. House drain pipes are clogged.
Water does not enter washer or it enters slowly
Water supply is not adequate in area. Water supply tap is not completely open. Water inlet hose are kinked. The filter of the inlet hose clogged.
Check another tap in the house. Fully open tap. Straighten hose. Check the filter of the inlet hose. Clean and straighten the drain hose. Clean the drain filter.
Water in the washer does not drain or drains slowly.
Drain hose is kinked or clogged. The drain filter is clogged.
Symptom Possible Cause
Electrical power cord may not be plugged in or connection may be loose. House fuse blown, circuit breaker tripped,or a power outage has occurred. Water supply tap is not turned on.
Make sure plug fits tightly in wall outlet. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap.
Washer does not start
Washer wont spin
Check that the door is firmly shut.
Close the door and press the Start/Pause button. After pressing the Start/Pause button, it may take a few moments before the clothes washer begins to spin. The door must lock before spin can be achieved. Once started, the door can not be opened for safety reasons. Wait one or two minutes before opening the door to give the electric locking mechanism time to release.
Door does not open
Wash cycle time delayed
The washing time may vary by the amount of laundry, water pressure, water temperature and other using conditions. If the imbalance is detected or if the suds removing program works, the wash time shall be increased.
Water supply is not adequate in area Water supply taps are not completely open. Water inlet hose are kinked. The filter of the inlet hose clogged. Drain hose is kinked or clogged. The drain filter is clogged. Load is too small. Load is out of balance. The appliance has an imbalance detection and correction system. If individual heavy articles are loaded(as like) bath mat, both robe, etc. this system may stop spinning or even interrupt the spin cycle altogether, if the imbalance is too great even after several spin starts. If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle. Is the door opened?
Check another tap in the house. Fully open tap. Straighten hose. Check the filter of the inlet hose. Clean and straighten the drain hose. Clean the drain filter. Add 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning
Close the door. If is not released, call for service. Unplug the power plug and call for service.
If the water overfills due to the faulty water valve, you will get display. is displayed if the water level sensor malfunction.
Close the water tap. Unplug the power plug. Call for service.
Over load in motor.
Warranty conditions for washing machine
1. The warranty period begins on the purchase date and is valid for 12 months. Begin of warranty period is proven if, the buyer submits purchase receipt together with the warranty card, filled in and signed by the seller. The serial number of the product must agree with the number entered onto the warranty card. 2. During the warranty period, we will correct any defects at no cost to you, if it can be proven that these are attributed to manufacturing or material defects. 3. Damages due to incorrect handling, noncompliance with instructions for use and normal wear are not covered by this warranty. Also, the warranty does not cover wear parts or easily broken parts (for example, viewing glass, light bulbs). The buyer is responsible for any damages during transport as well as shipping and packaging costs. 4. We decide whether to make repairs, exchange or replace parts. Exchanged or replaced parts are our property. The original warranty period is not prolonged if a refrigerator is repaired or certain parts are replaced. 5. The warranty is nullified if any person intervenes in the apparatus that are not authorised by LG Electronics, if the apparatus is used for commercial purposes. 6. Always keep the original packaging, so that if the apparatus requires servicing, it can be transported without damaging it. 7. If a repair is covered by this warranty, always contact your dealer or an authorised service centre. 8. Further claims are excluded. If parts of these provisions are invalid, they apply in the sense of the wording. The validity of the other provisions is not effected.
For offer a 12-month warranty for this apparatus
During the 12-month warranty period, we will repair your apparatus at no cost to you or make available spare parts to your dealer free, if this apparatus fails due to manufacturing or material defects. Further claims are excluded. We are not liable for damages due to acts of providence or damages occurring during transport. The buyer assumes shipping and packaging costs. Your warranty conditions on the rear also apply!
Type of apparatus : Name of buyer : Purchase date :
Serial number :
Dealers stamp and signature
Discovery 650 Aj3940 240TI EWF10479W Review Pioneer RG-1 TEW-431BRP Casio 2632 PSR19 DSC-P100 BM200 940UX Fujifilm A230 TX-28A1 AC-E60HG CT-P820 LD-2040WH 96 M Izek 1500 763MB N68-S UCC Cinema WI 102 8000I PS42B451 Pilot H360 XAV-W1 GV-series MV-700HR ENB39400W KIT R1 Veriton M261 UE-46C6700 MD 9470 ME-25 AE6070 VGN-NS21s W AD2022 VPL-EX70 42PC5D-UL PCV-V1-G RB-1572 DM-450 DP-8035 Serie 45 Kodak M340 GX 100 MX 16 Dobsonian XT10 TX-6500II Nokia 6310 DCS 620 VX5500 Wireless E5000 Cc-MC100W DM1050 Easyshare C140 Iphone 3G 9428 DS MC175 RP100 FX-570ES Plus 5 B Exploreur 3D Reference Card EWF8040W 7 0 DAR-RD100 MIM 2280 QV-2300UX Taurus X DMC-TZ11 Blackberry 8800 29FB5RNX ST-17 CE107M-S PSS-595 SD-10G Sigma Lens CP-X345WF 2 7 GPS 315 KDL-32BX300 SM-17SA GR-D720 17PT1565 Vegas 5 DJ-S17 WF7604SUV PW-AT760 F100-112 Linea 300 CFX12 Mkii MFC-6490CW Um 211 DV4941P STR-D550Z A 200 Explorer 395 DX630-JD
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101