WD-8025(0~9)S Name Power supply Size Weight / Max. Watt Wash capacity Water consumption Permissible water Pressure Spin Speed

WD-8025(0~9)N

WD-8025(0~9)T WD-80100TP/LWD-80250TP
Front loading washing machine 220-240V~ , 50Hz 600mm(W) 360mm(D) 850mm(H) 600mm(W) 440mm(D) 850mm(H) 600mm(W) 550mm(D) 850mm(H) 52kg / 2100W 3.5kg 42 l 57kg / 2100W 5kg 60 l 0.3 - 10kgf/cm2 (30~1000kPa) Rinse Hold / No Spin / 400 / 800 64kg / 2100W 6kg 72 l
The appearance and specifications may be varied without notice to raise the units quality.

I Accessories

Spanner

nstallation

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times. Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee.

Transit bolts

The appliance is fitted with transit bolts to prevent internal damage during transport. Packing and all transit bolts must be removed before using the washer. When unpacking the base, be sure to remove the additional packing support in the middle of the base packing.

Washer

Packing Support Base Packing

Removing transit bolts

1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs. If they are not removed, it may cause heavy vibration, noise and malfunction. 2. Unscrew the 4 bolts with the spanner supplied.
3. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use.
Whenever the appliance is transported, the transit bolts must be refitted. 4. Close the holes with the caps supplied.

I Washing Machine is to be connected to the water mains using new hosesets and that old hose-sets should not be used. I Connecting water supply hose
Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm2) Dont strip or crossthread when connecting Inlet hose to the valve. If the water supply pressure is more than 1000kPa, a decompression device should be installed. Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks. Check water tightness of washing machine connections by turning the tap completely on. Periodically check the condition of the hose and replace the hose if necessary.
Hot water tap Cold water tap
Make sure that there is no kink on the hose and that it is not crushed. When your washer has two valves, The Inlet hose which has red connector is for the hot water tap. If the washer has two valves, the energy is saved by using hot valve.

Cold Hot(option)

Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to

attach the tap.

2. Push the connector up till the
rubber packing is in tight contact with the tap. Then tighten the 4 screws.
3. Push the water supply hose
vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right.
Normal Tap without thread & one touch type inlet hose (Single inlet models)
1. Untighten the upper connector

screw.

2. Push the upper connector up till 3. Connect the water supply hose
the rubber packing is in tight contact with the tap. Then tighten the 4 screws. to the middle connector, pushing the plate down.
In case the diameter of the tap is large remove the guide plate. Turn the middle connector not to have water leaked. Make sure that the rubber seal is inside the hose connector. To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down.
Your machine comes with only cold water connection. Make sure that there are no kinks in the hose and that it is not crushed.
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children
Installation of drain hose

ca. 100 cm

ca. 145 cm

ca. 105 cm

When installing the drain hose sink, secure it tightly with a string. Proper securing of the drain hose will protect the floor from damage due to water leakage.

max. 100 cm

min. 60 cm

Laundry tub

Hose Retainer Tie strap

max. 100cm min. 60cm

The drain hose should not be placed higher than 100 cm above the floor. Proper securing of the drain hose will protect the floor from damage due to water leakage. When the drain hose is too long, do not force back into the washer. This will cause abnormal noise.

Level adjustment

1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.
Timber or suspended type flooring may contribute to excessive vibration or load balance errors.
Lock nut Adjustable feet Higher Lower
2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level) After the washer is level, tighten the lock nuts up towards of the base of the washer. All lock nuts must be tightened. Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

Adjustable feet

Concrete floors(tile.)
The installation surface must be clean, dry and level. Install washer on a flat hard floor. Before placing the washer on tiles, apply a rubber mat under the feet. Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.

Wooden floors

Rubber Cup
Wooden floors are particularly susceptible to vibration. To prevent vibration we recommend you place rubber cups under each foot, at least 15mm thick under the washer, secured to at least 2 floor beams with screws. If possible install the washer in one of the corners of the room, where the floor is more stable. Insert the rubber cups to reduce vibration. You can obtain the rubber cups (p/no.4620ER3001B) from the LG spares dept.

Important! Proper placement and levelling of the washer ensure long,regular and reliable operation. The washer must be absolutely horizontal and stand firmly in position. It must not Seesaw across corners under load. The installation surface must be clean, free from floor wax and other lubricant coatings.

are before washing

Caring before washing
1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one. Soil (Heavy, Normal, Light) Color (White, Lights, Darks) Lint (Lint producers, Collectors) Separate clothes according to amount of soil. Separate white fabrics from colored fabrics. Wash lint producers and lint collectors separately.

3. Caring before loading

Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
Check all pockets to make sure that they are empty. Items such as nails, hair clip, matches, pens, coins and keys can damage both your washer and your clothes. Close zippers, hooks and strings to make sure that these items dont snag on other clothes.
Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt.

A dding detergent

Adding detergent and fabric softener
1. The Dispenser Drawer 3. Detergent dosage
The detergent should be used according to the instruction of the detergent manufacture.
If too much detergent is used more than the recommended amount, too many suds can occur and this will decrease the washing result or cause heavy load to the motor. (Causing a malfunction) Use powder detergent only for the front loading washer.
Main wash only Pre Wash + Main Wash
2. Adding Fabric Softener
Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load. For best results, avoid oversudsing. Tips Full load : according to manufacturers recommendation. Part load : 3/4 of the normal amount. Minimum load : 1/2 of full load. Detergent is flushed from the dispenser at the beginning of the cycle.

125 ml

Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes. Do not leave the fabric softener in the detergent drawer for more than 2 days. (Fabric softener could harden) Softener will automatically be added during the last rinse cycle. Do not open the drawer when water is supplied. Solvents(benzene, etc) are not allowable.
Do not pour fabric softener directly on the clothes

unction

Recommended courses according to the laundry type
Fabric Program Type Temp. Proper Option Load
WD-8025(0~9)T WD-8025(0~9)S WD-8025(0~9)N WD-80100TP LWD-80250TP

Maximum

Cotton
First check if laundry is machine washable. (white cotton, linen towel and sheets.)

Pre Wash Rinse+

Rating
Color fast gaments (shirts, night dresses, 60C Pre Wash pajamas.)and lightly (40C,Cold ) Rinse+ soiled white cotton(underwear.) Synthetic Polyamide, Acryic, Polyester 40C Pre Wash (60C, Cold) Rinse+
Less than Less than 1.7 kg 2.5 kg

Less than 3.0 kg

Delicate
Delicate laundry easily damaged (silk, curtains.)

Cold (40C) Cold (40C)

Rinse+
Less than Less than 1.0 kg 1.7 kg

Less than 2.0 kg

Quick 30 Colored Laundry which is lightly soiled fast.
Less than Less than 1.0 kg 1.5 kg

Less than 2.0kg

Pre Wash : If the laundry is heavily soiled, Pre Wash Cotton is recommended. Pre Wash is available in Cotton and Synthetic Program. Rinse+: Used to introduce an additional rinse, which may assist in removing traces of detergent residue.

H ow to use washer

Synthetic Delicate Quick 30

Rinse+ No Spin

Rinse+Spin

Pre Wash

Rinse Hold

Program

Start/Pause

Option

1. Cotton automatically selected upon power on.
Press the Power( ) button to start. ) button.

2. Manual Selecting

Press the Power(

) button to start.

Press the Start/Pause( Initial condition - Wash : main wash - Rinse : 3 times - Spin : 800 rpm - Water temperature : 60C - Program : Cotton
Select the conditions which you want to use, by pressing each button. For selecting the each conditions, please refer to the page15~page20 Press the Start/Pause( ) button.
(1) Button : Program (2) Button : Start/Pause (3) Button : Option
(4) Button : Temperature (5) Button : Spin (6) Child Lock

(7) Button : Power

By pressing the Option button, all Option functions may be selected. - Rinse + Cold - Pre Wash

n Pre Wash

1. Rinse+
Used to additional rinse, which may assist in removing traces of detergent residue. By selecting Rinse+ function, the rinse time
Cotton Rinse+Spin Synthetic Delicate Quick 30

2. Pre Wash

If the laundry is heavily soiled, Pre Wash course is effective. Pre Wash is available in Cotton and Synthetic.
and the rinse water are increased. Program
Do not use Pre Wash stain removers on or near the Washer, as they may cause damage to the control panels finish.

Quick 30

Water Temp.
By pressing the Temp. button, the water temperature can be selected. - Cold - 40C / 60C / 95C

30 icate

No spin
By pressing the Spin button,+ the spin speed Rinse Rinse+ can be chosen.
No spin Pre Wash Rinse hold Cold Pre Wash Cold

Rinse+Spin hold Rinse

Option Spin

Temp. Option

1. Spin selection

1. Water Temperature

Delicate Quick 30 Synthetic Delicate Quick 30
Spin speed is available according to the program as follows.

Cotton Rinse+Spin Cotton

Synthetic
Water temperature can be selected as below according to the program.
- Cotton/Synthetic/Delicate/Quick 30 Option Temp. Program /Rinse+Spin Program Rinse Hold - No Spin - 400 - 800
Synthetic Delicate Quick 30 Synthetic Delicate Cotton Rinse+Spin Cotton
- Cotton Cold - 40C - 60C - 95C - Synthetic Cold - 40C - 60C - Delicate & Quick 30 Cold - 40C

2. No spin

Option Temp.
If no spin is selected, the washer stops Program after draining water. The required lamp will light up for identification.
Temp. Start/Pause Option Temp. Start/Pause Start/Pause
The required temperature lamp will light up for identification.

For the more detailed information, please refer to the page13.

3. Rinse Hold

Is selected by pressing the spin button repeatedly this function leaves clothes in the Start/Pause machine; suspended in the water after a rinse without entering into spin. To proceed through to a drain or spin, once the rinse hold function is completed using to Program button and Spin button to the required program. The required lamp will light up for identification.

Quick 30 Rinse+Spin

No spin Rinse hold No spin Rinse hold Pre Wash Cold Pre Wash Rinse+ Cold

ow to use washer

Cotton Rinse+Spin

Synthetic Delicate

Spin Child Lock Quick 30

Spin 1. Child Lock

Rinse Option
Child Lock can be set by Pre Wash pressing and Rinse hold holding the the Option and the Temp. button simultaneously.
Synthetic Delicate Quick 30 Cotton Rinse+Spin Synthetic
Program If you choose to lock the buttons on the control Option Option Temp. assembly to prevent tampering this function may be selected.

Start/Pause Power

OptionDelicate
Quick 30 Synthetic Delicate Program If the Program lamps are blinked (All program lamps blink) simultaneously after the power off or the end Rinse+ Start/Pause Option Temp. Option of the washing, the child lock Temp. Power mode is set. When child lock is set, all buttons are inoperable No spin Cancel the child lock mode by pressing the Rinse+Spin Cotton except power button. Program Cold Pre Wash Rinse hold Temp. and the Option button simultaneously To deactivate Child Lock system, press the Option Option Temp. Temp. for 3 seconds.
Cotton Rinse+Spin Synthetic Synthetic Delicate Delicate Quick Quick 3030 Cotton Cotton Rinse+Spin Rinse+Spin

Start/Pause Power Option

Option and the Temp. button simultaneously Program Program again.

Spin Option Temp.

Start/Pause30 Quick Delicate
Option Temp.Temp.Start/Pause Option
Start/Pause To change to the desired program, whilst Option Temp. in child lock mode. Program 1. Press both the Option and the Temp. Start/Pause Start/Pause Start/Pause Option Temp. together once again. 2. Press the Start/Pause button. 3. Select the desired program and press Option Temp. the Start/Pause buttonProgram again.

Cotton Rinse+Spin Synthetic Delicate Quick 30 Cotton Rinse+Spin
Change the desired program
The child lock can be set at any time and it is automatically canceled when operational errors occur. Also Child Lock works when Start/Pause power is off.
5 programs are available according to the laundry type. Lamp will light up to indicate selected program.

1. Program

When Start/Pause button is pressed, the Cotton program is automatically selected. - By turning the Program dial, the program is selected in order of Cotton-SyntheticDelicate-Quick 30-Rinse+Spin. Regarding to the laundry type for each program Please refer to the page13.

2. Course

-Cotton -Synthetic -Delicate -Quick 30 -Rinse+Spin Option Temp.
Option Temp. H ow to use washer

Power Start/Pause

1. Start
This Start/Pause( ) button is used to start wash cycle or pause the wash cycle.

1. Power

Press the Power button to turn power on Option Temp. and off

2. Pause

If temporary stop of wash cycle is needed, press the Start/Pause( ) button. When in Pause, the power is turned off automatically after 4 minutes. NB. The door will not open before 1 to 2 minutes when Pause is selected, or at the end of the wash cycle.

2. Initial Program

When the Power button is pressed, the washer is ready for Cotton program. And the other initial conditions as follows. So, if you want to advance into the Start/Pause Option Temp. T washing cycle without changing the Option program, just press the Start/Pause( ) button and then the washer will proceed. Initial program -Cotton Program/Main Wash Normal Rinse/800 rpm/60C

Time Left

Recommended program by manufacturer. - Cotton 95C : around 2 hours and 27 minutes - Cotton 60C : around 2 hours and 35 minutes - Synthetic : around 1 hour and 22 minutes - Delicate : around 56 minutes - Quick 30 : around 30 minutes - Rinse+Spin : around 20 minutes The washing time may vary by the amount of laundry, water pressure, water temperature and other washing conditions. If an unbalanced load is detected or if the suds removing program operates, the wash time may be extended. (Max. increasing time is 45minutes.)

M aintenance

Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside.

The water inlet filter

- Rinse+ , Pre Wash lamps will blink on the control panel when water does not enter the detergent drawer. - If your water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle brush.
4. Tighten up the inlet hose.

The drain pump filter

The drain filter collects threads and small objects left in the laundry. Check regularly that the filter is clean to ensure smooth running of your machine. ! CAUTION
First drain using the drain and then open the pump filter to remove whatever any threads or objects. Be careful when draining if the water is hot. Allow the water to cool down before cleaning the drain pump, carrying out emergency emptying or opening the door in an emergency.
2. Unplug the drain plug ( ), allowing the water to flow out. At this time use a vessel to prevent water flowing on to the floor. When water does not flow any more, turn the pump filter ( ) open to the left. 3. Remove any foreign material from the pump filter ( ). After cleaning, turn the pump filter ( ) clockwise and insert the drain plug ( )to the original place. close the lower cover cap.
1. Open the lower cover cap ( ) by using a coin. Turn the drain plug ( ) to pull out the hose.

Dispenser drawer

After a while detergents and fabric softeners leave a deposit in the drawer. It should be cleaned from time to time with a jet of running water. If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out. To facilitate cleaning, the upper part of the fabric softener compartment can be removed.

max max

The drawer recess
Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush. Once you have finished cleaning, replace the drawer and run a rinse cycle without laundry.

The washing drum

If you live in a hard water area, limescale may continuously build up in places where it cannot be seen and thus not easily removed. Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be replaced. Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal articles (paper clips, safety pins) which have been left in the drum. The washing drum should be cleaned from time to time. If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use. Descaler may contain chemicals that may damage part of your washing machine. Remove any spots with a stainless steel cleaning agent. Never use steel wool.

Cleaning your washer

1. Exterior Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral non abrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit surface with sharp objects. IMPORTANT: Do not use methylated spirits, diluents or similar products. 2. Interior Dry around the washer door opening, flexible gasket and door glass. Run washer through a complete cycle using hot water. Repeat process if necessary.
Remove hard water deposits using only cleaners labeled as washer safe.

Cold condition

If the washer is stored in an area where freezing may occur or moved in freezing temperatures, follow these instructions to prevent damage to the washer: 1. Turn off water supply tap. 2. Disconnect hoses from water supply and drain water from hoses. 3. Plug electrical cord into a properly grounded electrical outlet. 4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum. Close the door. 5. Set spin cycle and let washer spin for 1minute to drain out all water. Not all of the RV antifreeze will be expelled. 6. Unplug electrical power cord, dry the drum interior, and close the door. 7. Remove dispenser drawer drain and dry excessive water from the compartments. 8. Store washer in an uprignt position. 9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent. Do not add wash load.

roubleshooting guide

This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you contact your service provider.

Symptom

Rattling and clanking noise

Possible Cause

Foreign objects such as coins or safety pins maybe in drum or pump.

Solution

Stop washer and check drum and drain filter. If noise continues after washer is restarted, call your authorised service centre. If sound continues, washer is probably out of balance. Stop and redistribute wash load. If not removed during installation. Refer to Installation guide for removing transit bolts. Wash load may be unevenly distributed in drum. Stop washer and rearrange wash load. Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary. Too much detergent or unsuitable detergent may cause excessive foaming which may result in water leaks.

Thumping sound

Heavy wash loads may produce a thumping sound. This is usually normal. Have all the transit bolts and packing been removed? Are all the feet resting firmly on the ground?

Vibrating noise

Water leaks.
Fill hoses or drain hose are loose at tap or washer. House drain pipes are clogged.

Oversudsing

Water does not enter washer or it enters slowly
Water supply is not adequate in area. Water supply tap is not completely open. Water inlet hose(s) are kinked. The filter of the inlet hose(s) clogged.
Check another tap in the house. Fully open tap. Straighten hose. Check the filter of the inlet hose. Clean and straighten the drain hose. Clean the drain filter
Water in the washer does not drain or drains slowly.
Drain hose is kinked or clogged. The drain filter is clogged.

Symptom Possible Cause

Electrical power cord may not be plugged in or connection may be loose. House fuse blown, circuit breaker tripped,or a power outage has occurred. Water supply tap is not turned on.
Make sure plug fits tightly in wall outlet. Reset circuit breaker or replace fuse. Do not increase fuse capacity. If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap.

Washer does not start

Washer will not spin
Check that the door is firmly shut.
Close the door and press the Start/Pause button. After pressing the Start/Pause button, it may take a few moments before the clothes washer begins to spin. The door must lock before spin can be achieved. Once started, the door can not be opened for safety reasons. Wait one or two minutes before opening the door to give the electric locking mechanism time to release.

Door does not open

Wash cycle time delayed
The washing time may vary by the amount of laundry, water pressure, water temperature and other usage conditions. If the imbalance is detected or if the suds removing program works, the wash time shall be increased.

Water supply is not adequate in area Water supply taps are not completely open. Water inlet hose(s) are kinked. The filter of the inlet hose(s) are clogged. Drain hose is kinked or clogged. The drain filter is clogged.

No Spin

Rinse Wash Pre Rinse+
Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose. Clean and straighten the drain hose. Clean the drain filter.

Rinse+ +

Pre Wash Pre Wash Pre Wash
No Spin Rinse Hold No Spin Rinse+
Rinse Hold Rinse Hold No Spin Hold Rinse Pre Wash Rinse+
Load is too small. Load is out of balance. + Rinse+Wash Rinse Rinse Hold Pre The appliance has an imbalance + Rinse No Spin detection and correction system. If No Spin + Spin RinseNo No Spin Rinse Holdindividual heavy articles are loaded Pre Wash Rinse Hold Pre Wash Rinse Hold No Spin (ex. bath mat, both robe, etc.) this system Rinse Hold Pre Wash Rinse+ may stop spinning or even interrupt the Rinse Hold Pre Wash + Rinse spin No Spin cycle altogether. Rinse+ No SpinIf the laundry is still too wet at the end of No Spin Rinse Hold Rinse+ Pre Wash the Rinse+Wash Cold Rinse Hold cycle, add smaller articles of laundry Pre Rinse Hold Pre Wash toNo Spin balance the load and repeat the spin Rinse+ No Spin Rinse+ cycle. Cold Rinse Hold Pre Wash
Add 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning
No Rinse Hold Spin No Spin

Pre Rinse+ Wash

No Spin Rinse Hold

Is the door opened?

Close the door. If door error is not released, call for service.

Cold Cold

Unplug the power plug and call for service.

Cold Cold Cold

No Spin Cold
Rinse Hold No Spin No Spin Cold
Water overfills due to the faulty water valve.
Close the water tap. Unplug the power plug. Call for service.

Rinse Spin No Hold

Water level sensor has malfunctioned.
Cold Rinse Hold Rinse Hold + RinseCold

Rinse+Wash Pre

Pre Wash 26

Pre Wash Cold Cold

Rinse+ Pre Wash + Rinse

erms of Warranty

What Is Not Covered: