WASHING MACHINE SERVICE MANUAL

CAUTION

READ THIS MANUAL CAREFULLY TO DIAGNOSE TROUBLES CORRECTLY BEFORE OFFERING SERVICE.
MODEL : WD-8050F/WD-1050F/WD-1250F WD-8050FH/WD-1050FH/WD-1250FH WD-8052X/WD-1052X WD-8052XH/WD-1052XH

P/No.:3829FR9043S

CONTENTS
1. SPECIFICATION....3 2. FEATURES & TECHNICAL EXPLANATION... 4 3. PARTS IDENTIFICATION... 6 4. INSTALLATION..... 7 5. OPERATION.....10 6. WIRING DIAGRAM.....12 7. TROUBLE SHOOTING....13 7-1.BEFORE SVC CHECKING...13 7-2.TEST MODE....13 7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY..13 7-4.ERROR DISPLAY....14 8. ERROR DIAGNOSIS AND CHECK LIST...15 8-1. DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION..15 8-2. FAULT DIAGNOSIS AND TROUBLE SHOOTING...18 9. DISASSEMBLY INSTRUCTIONS....24 10. EXPLODED VIEW AND PARTS LIST....31 10-1. THE EXPLODED VIEW OF CABINET ASSEMBLY..31 10-2. THE PARTS LIST OF CONTROL PANEL AND DISPENSER ASSEMBLY..34 10-3. THE PARTS LIST OF DRUM AND TUB ASSEMBLY..36 RAPPENDIX (The type of power cord)...39

1. SPECIFICATION

POWER SUPPLY PRODUCT WEIGHT WASHING ELECTRICITY CONSUMPTION SPIN(800rpm) DRAIN MOTOR WASH HEATER REVOLUTION SPEED WASH SPIN

WD-1050F(H)/1250F(H)

WD-8050F(H)/8052X(H)/1052X(H)
AC 220-240V, 50Hz / 60Hz 67kg 190W 300W 32W 2000W 45rpm 400/600/800/(1000)/(1200) rpm 0.3-10kgf/(30-1000kPa) Electronic 7.0kg/6.0kg
OPERATION WATER PRESSURE CONTROL TYPE WASH CAPACITY
Synthetic (4.0kg), Delicate (3.0kg) Wool (2.0kg)
DIMENSION WASH PROGRAM RINSE DOOR SWITCH TYPE WATER LEVEL RESERVATION SENSING OF THE LAUNDRY AMOUNT FUZZY LOGIC DISPLAY OF THE REMAINING TIME ERROR DIAGNOSIS POWER AUTO OFF CHILD LOCK AUTO RESTART ECO RAPID
600mm(W)600mm(D)850mm(H) Coloreds, Whites, Synthetic, Delicate, Wool Super, Normal, Hold Bi-Metal type 9 steps (by sensor) From 3 hours to 19 hours Adopted Adopted Adopted 7 items Adopted Adopted Adopted Adopted Adopted -
2. FEATURES & TECHNICAL EXPLANATION

2-1.FEATURES

Jumbo drum
LGs jumbo drum can wash about 40% more per load than conventional washing machine. A bigger durm improves the wash performance.
More economical by Fuzzy Logic System
FUZZY Logic System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.

Child-Lock

Temp Eco/Rapid
The Child-Lock system has been developed to prevent children from pressing any button to change the programme during operation.
Low noise speed control system
By sensing the amount of load and balance, evenly distributes load to minimize the spinning noise level.

Auto Restart

Although the washing machine is turned off by a power failure, it restarts automatically in its stopped process when power is supplied again. and it will be the same when the machine unplugged in operation is plugged in again.
2-2.DETERMINE WASHING TIME BY FUZZY LOGIC
To get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount.
water temperature washing time
selected washing temperature

FUZZY LOGIC

rinse time spin rhythm, time
the best washing performance

laundry amount

SENSING

PROCESSING

DETERMINATION

EFFECT

2-3.WATER LEVEL CONTROL

This model adopts a pressure sensor which can sense the water level in the tub. When the water level reaches to the preset level water supply is stopped, then washing program proceeds. Spinning does not proceed until the water in the tub reduces to a certain level.
2-4.THE DOOR CAN NOT BE OPENED
UWhile program is operating. UWhile Door Lock light turns on.

3. PARTS IDENTIFICATION

Power plug
If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or a similarly qualified person in order to avoid a hazard.

Drawer

(For detergent and fabric softener)

Control panel

Drain hose Door
Lower cover Drum Drain pump filter Drain plug Levelling legs Lower cover cap

ACCESSORIES

Inlet hose

Spanner

4. INSTALLATION
Before servicing ask troubles of customers Check the adjustment(power supply is 220-240V, remove the transit bolts.) Check the troubles referring to the trouble shooting. Decide service steps referring to disassembly instructions. And then, service and repair. After servicing, operate the appliance whether it works O K or NOT.

STANDARD INSTALLATION

The appliance should be installed as follows.

REMOVE THE TRANSIT BOLTS

URemove the transit bolts (4EA: )with supplied spanner. UKeep the transit bolts and spanner for future use.
INSTALL THE APPLIANCE ON FLAT AND FIRM SURFACE

ADJUST THE HORIZONTAL

UTurn the leveling feet to set the appliance horizontally.

Low High

UThe appliance goes up by rotating the feet clockwise. UThe appliance come down by rotating the feet counter clockwise.
HOW TO CONNECT INLET HOSE
UCheck that the rubber packing is inside of the valve connector. UConnect the inlet hose firmly to prevent leak.

CONNECT DRAIN HOSE

Make sure that the hose is not twisted.
Avoid submerging the end of the hose.
The drain hose should be placed under 85from the floor. CONNECT POWER PLUG
Connect the power plug to the wall outlet.
Avoid connecting several electric devices, It may be the cause of the fire.

GTEST OPERATION

Preparation for washing. Press the power button. Press the START/PAUSE button.
U Connect the power plug to the outlet. U Connect the inlet hose.
U case of Coloreds program. In

Check the water heating.

Check automatic reverse turn.

Check the water supply.

Press the button TEMPB A and the present temperature will be displayed. a WD-1050F(H)/1250F(H)b
Check if the drum rotates clockwise and counterclockwise.
Check if water is supplied through the detergent dispenser.

Check drain and spin

Turn off Wash and Rinse after pressing the Start/Pause button and start the machine again. Check drain and Spin.
Power off and open the door

Water removal

Power off and then power on. Check if the door can be opened after Door Lock lamp turns off.
SVC is needed during If check, remove the remaining water by pulling out the hose cap.

5. OPERATION

LED display
UDisplay the remaining time (Hour : Minute ) to finish. UIn case of abnormal operation, error indications are displayed. ( ) USee trouble shooting guide.
Water temperature selector
UPress the button to select water temperature. UThe water temperature [40 A60 Acold] can be selected in Coloreds, C C Synthetic U95 is selected for Whites only. C UBy pressing the button during operating the washer, the present temperature is displayed.

Error display.

UThe display blinks if there is an error. 14 Refer Uno inlet : Trouble with water supply. Uimbalance : The laundry is tilted to one side. Uno drain : If the drain pump filter is clogged.

Door lock lamp

U shows whether the door It can be opened or not. U when the lamp is on, the door cant be opened.
For manual wash, rinse and spin speed
U Use these buttons to change wash/rinse/spin U When lamp is off, no selection has been made. U Prewash is available for Coloreds, Whites, Synthetic

Rinse hold

U you desire to leave fabrics in the machine If without spinning after rinse to prevent them getting wrinkled, you may select rinse Hold by pressing the Rinse button. U drain and spin, press the Rinse button to To turn off the rinse Hold lamp.

h program selector

grams can be set depending on the of the laundry. power button is pressed. reds program is automatically set. ressing the button, [ Coloreds A esASyntheticADelicateA Wool ] be selected.

Start/Pause button

U Use the button to start or pause wash cycle. U The power turns off automatically 4 minutes after the pause button is pressed.

Power button

UPress the button to turn power on and off.

Child - lock

UChild Lock system can be set and canceled by pressing both [Temp] and [Eco/Rapid ] button simultaneously. UOnce Child Lock is set, all button are inoperable. UChild Lock system can be set anytime even during Power-off, on pause and operation. UIt is automatically cancelled when an operational error occurs and when the cycles ends.
s the button when delayed washing is ed. n the button is pressed, [ ]is ayed, A maximum delay of [ ]hours be set. press advances time delay by the hour. [Power]button to cancel [Time Delay].

Eco/Rapid

U you push the Eco/Rapid button in White program, If Eco function is selected. Eco function gives you almost the same washing effect as that in 95 with C less energy consumption U you push the Eco/Rapid button in Coloreds or If Synthetic program, Rapid function is selected. Rapid function reduces the whole time including the washing and rinsing time about by half an hour.

6. WIRING DIAGRAM

7. TROUBLE SHOOTING

7-1.BEFORE SVC CHECKING

Be careful of electric shock while trouble shooting. Disconnect power plug from the outlet before service.

7-2.TEST MODE.

If you press Powerb a button with botha Rinseb a and Spinb buttons pressed the machine can be gotten into the test mode. To check if functions operate well, pressa Start/Pauseb button in test mode as follows.
NOTE : Even if you press the button to check inlet valve, inlet valve does not operate until the drum
comes to a complete stop from spinning. Times of press None 1 time 2 times 3 times 4 times 5 times 6 times 7 times 8 times 9 times 10 times Checking Point All lamps turn on Counterclockwise spin Low speed Spin High speed Spin Inlet valve for pre-wash operation Inlet valve for main-wash operation Inlet valve for main-wash operation Clockwise spin The Heater is in operation for 3 sec. Draining pump operation Auto off operation 3~6 (Drum rpm 10) 55~65 (Drum rpm 10) 95~105 (Drum rpm 10) Water level frequency(25~65) Water level frequency(25~65) Water level frequency(25~65) 3~6 (Drum rpm 10) Water Temperature Water level frequency Display Status
7-3.HOW TO KNOW THE WATER LEVEL FREQUENCY
RPress the Wash and Rinse buttons simultaneously.
The last two digits means water level frequency(10-1 ) If water is added in operation, number 6 will appear. ex) 641 : Water level frequency = 24110-1 is ommitted) ( 2 Water is added.

7-4.ERROR DISPLAY.

UIf you press the Start/Pauseb a button in error condition, any error except PE will disappear and the machine will change into pause status. U case of PEH tEH dEHif the error is not resolved within 20 sec., and in case of other errors, if In G , G , G , the error is not resolved within 4 min., power will be turned off automatically and the error only will be blinked. But in case of FEH G , power will not be turned off. ERROR

1 WATER INLET ERROR

SYMPTOM
WD-1050/1250 WD-8050/8052/1052
Water has not reached to the pre-set level within 4

no inlet

min. since inlet val ve operated or water has not reached to the normal level within 25 min.

IMBALANCE ERROR

The appliance is tilted.

imbalance

Laundry is gatherd to one side. Non distributable things are put into the drum.

DRAIN ERROR

no drain
Water has not drained enough within 5 min.

OVER FLOW ERROR

Water is automatically being pumped out because too much water is in the tub.
SENSOR PRESSURE S/W ERROR
The sensor pressure switch is out of order.

DOOR OPEN ERROR

The Start/Pauseb a button is pressed with the door open. The door switch is out of order.
THERMISTOR ERROR The thermistor is out of order.
8. ERROR DIAGNOSIS AND CHEK LIST
8-1.DIAGNOSIS AND ANSWER FOR ABNORMAL OPERATION

SYMPTOM NO POWER

GUIDE FOR SERVICE CALL
Is the power plug connected firmly to AC220-240V outlet?
Power failure? or Breaker opened?

Visit to check

Water inlet trouble Is "no inlet" displayed?

Is the tap opened?

Is the tap frozen?
Is the water supply shut-off?
Is filter in the inlet valve clogged with foreign material?
Clean the filter of inlet valve
SYMPTOM DOOR OPEN ERROR Refer to 7-4 ERROR DISPLAY
Did you press theA Start/PauseB button when the door is open?

Close the door

Visit to check < Check if the door switch is O.K >

Drain Trouble

Is "no drain" displayed?
Is the debris filter clogged with foreign material such as pin, coin and etc.?

Clean up the filter.

Is the drain hose frozen with water, kinked or crushed?
SYMPTOM Suds overflow from the appliance. (In this condition, wash and spin do not operate normally)
GUIDE FOR SERVICE CALL Is Low-sudsing detergent for the durm washing machine used?
Is the proper amount of detergent used as recommended? YES Recommend to reduce the using amount of detergent.

LOW LATHERING DETERGENT

TThis appliance has the automatic suds sensing function which operates under much suds condition for good rinse and preventing overflow. T When much suds are sensed, suds removing fuction such as drain, water input and pause will operate without rotating the drum.

No effect of softener

Is softener put in the correct compartment of drawer?

Compartment for softener

Is the drawer closed during wash?
Is the softener cap clogged?
Explain how to use softener < Clean the compartment for softener > OVER FLOW ERROR PRESSURE S/W ERROR THERMISTOR ERROR Refer to 7-4. ERROR DISPLAY Visit to check
8-2.FAULT DIAGNOSIS AND TROUBLE SHOOTING
1. Be careful of electric shock or disconnecting the parts while trouble shooting.
2. First of all, check the connection of each part terminal with wiring diagram. 3. Voltage between each terminal is AC 220-240V while applying an electric current (except secondary part of the transformer and sensors)

NO POWER

When measuring the voltage of the outlet, is the voltage AC 220-240V?

Check the fuse?

When measuring the voltage of blue connector of the PWB assy (Power), is the voltage AC 220-240V?

PWB ASSY (POWER)

Replace PWB assy (Power)
Is connector disconnected or or is the contact bad or cut?
Reconnect and repair connector.
Is wire of the PWB assy(Display) disconnected? Replace PWB assy(Main)

NO YES

Replace PWB assy(Display)

NO WATER SUPPLY

Open the tap.
When you press bothA WashB button and RinseB A buttons simultaneously, is the water level frequency YES below 40? NO Is the inlet valve filter clogged with impurity?
Check the chamber(Air) and the tube clogged with impurity.

Clean the filter.

Is resistance of the inlet valve connector between 2 to 8 k ?

Replace the inlet valve.

Check the voltage between each terminal of inlet Valve is AV 220~240V. (Refer to 7-2 TEST MODE)

Replace PWB assy(Main)

DETERGENT DOES NOT FLOW IN

Is water supplied?

Refer to solution A INLETB NO

Wiring diagram

Are replaceptacles correctly connected to the terminals of inlet valve? YES Is detergent put in the correct compartment of the drawer?
Check the wiring on the dispenser. Put the detergent in the correct position
SOFTENER MAIN PRE WASH WASH
PRE+MAIN MAIN WASH : Detergent

Is the detergent hardened?

Clean the drawer.

SOFTENER DOES NOT FLOW IN
Refer to ANO WATER SUPPLYB Check the wiring on the dispenser.
Are receptacles conectly connected to the terminals of NO inlet valve?
Is softener put in the correct compartment of

drawer?

Put it in the correct compartment.
Is the softner cap clogged?
Clean the cap and drawer.

ABNORMAL SOUND

Is the pulley bolt loosened?

Fix the bolt tightly.

Is the belt worn? Replace the V-belt (4400FR3116A)

YES NO

Is there friction noise from the motor?

Replace the motor.

HEATING WITHOUT WATER
When pressing WASHand RINSEbuttons at the same time after dranining, is the water level frequency 52 or more? When pressing WASH, RINSEbuttons at the same time while wash, is the water level frequency between 20~40?
Replace the sensor (pressure)

PWB ASSY(POWER)

Replace the PWB assy (POWER or MAIN)

AC 220-240V

DRAIN MALFUNCTIONING
Is the drain hose kinked or frozen?

Repair drain hose

Is the filter of drain pump clogged?

Remove foreign material.

Is the connector disconnected or is the contact bad?
Reconnect or repair the connector
Is the coil of drain pump cut-off? (resistance of coil is 90~160 )

Replace the pump assy

When checking voltage between two receptacles as shown (L M on spinning, is the voltage AC , ) 220-240V ? Replace the PWB assy (Main)

PWB ASSY(MAIN)

WASH HEATER TROUBLE
When checking the voltage between two receptacles of the PWB assy(Power) during washing. Is the voltage AC 220-240V?
Replace the PWB assy (Power)
After power off, is the resistance between yellow wire and red wire of connector 10 to 30 ?

Normal

Yellow
After power off, is the resistance of heater 10 to 30 ?

Replace the heater assy

HEATING WATER CONTINUOUSLY ABOVE THE SELECTED WATER TEMPERATURE
Is the resistance between two receptacles with BL/WH wires parted from PWB assy 2.5k to 180k (105 ~0 )?
Replace the thermistor (6322FR2046B)
When checking thermistor on the tub cover, is the thermistor gotten more than 2 mm out of the rubber? Get the thermistor back to the rubber.

SPIN TROUBLE

Check the frequency of the water level 48 or more. The frequency can be checked by pressing the Wash and Rinse buttons at the same time. Check the sensor (Pressure) or hose (Sensor). If the problem is on the sensor or the hose, replace the sensor or the hose.

Press Power button with both Rinseand Spin buttons pressed after power off. Press Start/Pause YES button 2 times. Does the drum rotate at low spin speed?
Is it disconnected or badly contacted? a Natural:3pin( ),Red:4pin( ),Blue:2pin( ), Yellow:2pin( )b

Reconnect or repair it.

Check the motor connector, is the resistance between the terminal in figure the same as below? Resistance between terminals ~ :0.5~1.0 :1.5~2.5 ~
Replace the motor assy. (4681FR1194A)
Be sure to unplug the machine before measuring. MOTOR TERMINAL
Replace the PWB assy (Main)
9. DISASSEMBLY INSTRUCTIONS
RBe sure to unplug the machine out of the outlet before disassembling and repairing the parts.

CONTROL PANEL

Unscrew 2 screws on the back of the top plate. Pull the top plate backward and upward as shown.

PLATE ASSY(TOP)

Disconnect the PWB assy (Display) connector.
Pull out the drawer and unscrew 3 screws. Push 2 upper hooks down and pull the control panel.

PANEL ASSY(CONTROL)

PWB ASSY(DISPLAY)
Disconnect the PWB assy (Display) from the control panel by unscrewing 9 screws.
Disassemble the top plate assy. Unscrew 2 screws. Disconnect connector from the wiring.

DISPENSER ASSY

Disassemble the top plate assy. Pull out the drawer slightly upward. Unscrew 2 screws.

DRAWER

Disassemble hose clamps and hoses Disassemble ventilation bellows and water inlet bellows from tub.

DISPENSOR ASSY

INLET VALVE
Disconnect the wiring receptacle. Unscrew 2 screws from the back. When reconnecting the connector
VALVE#1(MAIN) VALVE#2(PRE) VALVE#3(HOT)
(Option) Unscrew 2 screws
White/Black - Black Gray/White - Black Blue/Red - Black

REACTOR

Disconnect the wiring connector from the PWB assy(Msin)
Unscrew 2 screws Pull the PWB assy(Main) as shown.

LOWER COVER

Open the lower cover plate by using coin and pull out the lower cover in the arrow direction after a screw is unscrewed.

Open the door completely. Remove the two screws from the hinge.

GASKET ASSY

Take apart the cabinet gasket clamp. Unscrew 2 screws from the cabinet cover. Open the lower cover cap and unscrew 1 screw inside Take apart the lower cover
Unscrew all the screws on the upper and lower sides of the cabinet cover.
Take apart the tub gasket clamp Make sure that the drain hole of the gasket is put beneath when reassembling the gasket. Refer to the arrow mark on the tub cover.

PULLEY, MOTOR, DAMPER

Remove the back cover. Take off the belt turning the pulley. Unscrew the bolt to pull out the pulley.

(PULLEY)

Unscrew 2 screws from the bracket. Push the motor in the arrow direction for disassembling. When reassembling the motor, make sure that motor
mounting rubbers are not taken off from the bracket.

(MOTOR)

Hinge, Damper

Damper

Pull out the hinge pressing its snap. Do not use the pulled out hinge again.it may be taken off during operation.

(DAMPER)

Clean the drain pump filter
Open the lower cover cap ( L ) by using coin.Turn the drain plug ( M) to pull out the hose.
Unplug the drain plug ( M) , then the water flows out, At this time use a vessel to prevent water flowing on the floor. If the water does not flow any more,turn the pump filter ( N) open to the left. Take out any foreign material
from the pump filter ( N). After cleaning, turn the pump filter(N) clockwise and insert the drain plug ( M)to the original place. close the lower cover cap.

Pump Outlet Hose

Remove pump outlet hose. Remove tub pump bellows. Remove cap(Remaining Hose.) Disconnect the wiring. Unscrew 3 screws Remove the pump.

Cap (Remaining Hose)

Tub Pump Bellows

HEATER

Unscrew 3 screws fixing the heater protecting cover. Loosen the M6 heater nut to pull out the heater.
When mounting the heater, be sure to insert the heater into the heater clip on the bottom of the tub.

THERMISTOR

Pull it out by holding the thermistor bracket. TIf it is pulled by the wire, it may be broken. When mounting the thermistor again, make sure that it is got back tight to the rubber.

DOOR HINGE ASSY

Disassemble the door from the door hinge. Take apart the cabinet cover clamp and release the gasket. Unscrew 2 screws on the door hinge. Push the door hinge arm to the inside of the cabinet cover for disassembling.

SWITCH ASSY, DOOR LOCK

Take apart the cabinet cover clamp and release the gasket. Unscrew 2 screws holding the Door Lock. Disconnect the door lock from the wiring connector.

WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
Remove the heater. Remove the foreign material (wire, coin and others) by inserting a long bar through the hole.
10. EXPLODED VIEW AND PART LIST
10-1.THE PART LIST OF CABINET ASSY

A-1 A-2

A-47 A-45 A-44 A-41 A-40 A-39 A-38 A-37 A-35 A-34 A-33 A-32 A-31 A-30 A-28 A-10 A-27 A-7 A-8 A-50 A-43 A-6 A-5
A-11 A-13 A-26 A-14 A-15 A-16 A-17 A-18 A-23 A-49 A-21 A-22 A-19
THE PART LIST OF CABINET ASSY
A-1 A-2 A-5 A-6 A-7 A-8 A-10

PART NAME

PLATE ASSY(TOP) SCREW, TAPPING TRUSS HEAD BACK COVER SCREW, TAPPING TRUSS HEAD CABINET ASSY SCREW, TAP TITE(S) BINDING HEAD POWER CORD ASSY *See Appendix(type of power cord)

PART NO.

3828ER1001A 1TTL0403018 3808FR1202A 1TTG0402618 3091FR0045A 1SBF0402418 6411FR1169B 6411FR1169D 6411FR1169E 6411FR1169F 6411FR1169K 6411FR1169L 6411FR1169N 6411FR1169P 6411FR1169Q

SVC CORD R

1 R R R R 2 2
C-4-2 S-2-1 B-5 B-3 B-3(BSI) B-3(SISIR) C-4-2 S-2-3 S-2-1
A-11 A-13 A-14 A-15 A-16 A-17 A-18 A-21 A-22 A-23 A-26 A-27 A-28 A-29
SCREW SCREW, TAP TITE(S) BINDING HEAD SENSOR PRESSURE BASE SCREW, TAPPING TRUSS HEAD BRACKET, BASE FEET ASSY COVER, LOWER SCREW, TAPPING TRUSS HEAD CAP(REMAINING HOSE) CLAMP ASSY, CABINET GASKET GUIDE SCREW SCREW, TAPPING TRUSS HEAD
4000W4A003A 1SBF0402618 6600FR1203F 3040FR0049A 1TTG0403018 4810FR4136A 5413FR4154A 3550FR1166A 1TTG0402618 5006FR3146A 2W20017A 4974ER4001A 4000FD4191A 1TTL0403032
A-30 A-31 A-32 A-33 A-34 A-35 A-37 A-38 A-39 A-40
SWITCH ASSY, DOOR LOCK SCREW HINGE ASSY SCREW, TAPPING TRUSS HEAD COVER, CABINET SCREW, TAP TITE(C) PAN HEAD HOLDER HOLDER SCREW, TAP TITE(S) PAN HEAD PWB ASSY(MAIN) WD-1050F/1250F/1052X/8050F&8052X WD-1050FH/1250FH/1052XH/8050FH&8052XH
6601ER1001A 4000FD4191A 4775FR2114A 1TTL0403032 3550FR1213A 1TPL0402618 4930FR4157A 4930ER4001A 1SCBF040327 6871FC1006A/C/E/G 6871FC1006B/D/F/H 1TTL0403018 6871FC2262C 4930FR3151A 4011FR3159A 4830FR3107A 3581ER1001A 5006FR3179A 5874FA2381B

SPEC 220-240VAC

220-240VAC 220-240VAC
A-41 A-42 A-43 A-44 A-45 A-47 A-49 A-50
SCREW, TAPPING TRUSS HEAD PWB ASSY (POWER) HOLDER BOLT ASSY, TRANSIT BUSHING DOOR ASSY LOWER COVER CAP REACTOR

220-240VAC

10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSY

B-1 B-24

B-2 B-21 B-4

B-5 B-6 B-7

B-9 B-10 B-11 B-12 B-13

B-17 B-14

THE PARTS LIST OF CONTROL PANEL & DISPENSER ASSY

B-1 B-2 B-4

SCREW, TAP TITE(S) PAN HEAD VALVE HOSE ASSY, INLET
1SCPF040268 5220FR1251A 5214FA1146 5215FD3715 3W40102

R R R R

B-5 B-6 B-7 B-8 B-9 B-10 B-11 B-12 B-13 B-14 B-15
HOSE CONNECTOR (MECH), DRAIN HOSE SCREW, TAP TITE(B) FLAT HEAD HOSE ASSY, DRAIN HOSE, PUMP CLAMP CLAMP BELLOWS RING, SNAP SCREW PWB ASSY(DISPLAY) WD-1050F(H)/1250F(H) WD-1052X(H)/8050F(H)&8052X(H)
5214FR4125B 4932FR3156A 1SBF0402618 5214FR3018B 5214FR3188A 4861FR3068C 4860FR3092D 4738FR2065A 3W500120 4W51132A 6871EC2002A/B 6871EC2002C/D 3721ER1003 1TTL0403332 6877ER1001C 3721ER1002 4925FR1137C 4925FR1137A 4925FR1137F 4925FR1137G 3W50712A WD- SSSSS H Series 5220FR1280A R R R R R R R R R

B-16 B-17 B-18 B-19 B-21

PANEL ASSY, CONTROL SCREW, TAPPING TRUSS HEAD LEAD WIRE ASSY PANEL ASSY, DRAWER DISPENSER ASSY WD-8050F/8052X WD-8050FH/8052XH WD-1050F/1052X/1250F WD-1050FH/1052XH/1250FH

B-22 B-24

DRAIN HOSE HANGER VALVE
10-3 THE EXPLODED VIEW OF DRUM & TUB ASSY
C-44 C-43 C-42 C-45 C-46 C-1

C-41 C-49

C-40 C-39 C-38 C-37 C-36 C-35 C-47 C-34 C-33 C-6 C-2 C-3 C-4 C-5
C-7 C-9 C-10 C-31 C-26 C-27 C-25 C-24 C-8 C-48 C-11 C-12 C-13 C-14 C-15 C-16 C-17 C-23 C-22 C-30 C-21 C-20 C-19 C-18
THE PART LIST OF DRUM & TUB ASSY
L/No. C-1 C-2 C-3 C-4 C-5 C-6 C-7 C-8 C-9 C-10 C-11 C-12 C-13 C-14 C-15 C-16 C-17 C-18 C-19 C-20 C-21 C-22 BOLT ASSY BELT, POLY-V PULLEY TUB ASSY BRACKET SPRING SCREW SCREW BRACKET, MOTOR SCREW MOTOR ASSY DAMPER ASSY HINGE BOLT ASSY WEIGHT, BALANCE CLAMP HOSE(SENSOR) CHAMBER, AIR CLAMP, HOSE BELLOWS CLAMP, HOSE PUMP ASSY(DRAIN)
4011FR3173A 4400FR3116A 4560FR1149A 3045FR0031C 4810FR4167A 4970FR2084B 1SZZFA4362A 4040FR4051F 4810FR1222B 1SZZFA4362A 4681FR1194A 4901FR2080A 4774FR3118A 4011FR3173B 4844FR1179A 4860FR3092C 5214FR4125A 3504FR3134A 4861FR3068C 4738FR1145A 4861FR3068E 5859FR1225E 5859FR1225F

SVC CORD

QTY 1

220-240VDC

1 220-240VAC/50Hz 220V/60Hz

C-23 C-24 C-25 C-26

SCREW, TAPPING TURSS HEAD PROTECTOR (MECH) SCREW, TAPPING TURSS HEAD HEATER ASSY
1TTL0403018 3740FR3043A 1TTL0403318 5301FR1158B 5301FR1158C 5301FR1158D R
240VAC2000W 220VAC2000W 230VAC2000W
L/No. C-27 C-30 THERMISTOR PUMP MOTOR
6322FR2046B 4681EA2001A 4681EA2001B

QTY 3

220-240VAC 50Hz 220VAC60Hz

C-31 C-33 C-34

RUBBER BRACKET GASKET ASSY WD-1050/1052/1250 series WD-8050/8052 series
5040FR4168A 4810FR4116A 4987FR1165B 4986FR1230B 3044FR0027A 1TTL0403318 4036FR4123A 4860FR4124A 3044FR0036C 4970FR2084A 4930FR3040A 4844FR1223A 1SZZFA4362A 4810FR4166A 1TTL0503518 4810FR4126A 4861ER2001A 1NZZFR4175A 4810FR4126B R R R R R

220-240VAC 50Hz

C-35 C-36 C-37 C-38 C-39 C-40 C-41 C-42 C-43 C-44 C-49 C-46 C-47 C-48 C-49
COVER, TUB SCREW, TAPPING TURSS HEAD SEAL CLAMP, TUB TUB, DRUM ASSY SPRING HOLDER(SPRING) WEIGHT, BALANCE SCREW BRACKET SCREW BRACKET TUB GASKET CLAMP ASSY NUT BRACKET (UPPER RIGHT)
APPENDIX(The type of power cord)
TYPE TYPE OF PLUG POWER CORD P/No.
2A 2PIN 3.5 EPIN 5 B-2 5A 2PIN 5 EPIN 7 15A 2PIN 7 EPIN 8.6

6411FR1169F

7 8.5 25.6

6411FR1169E

TYPE OF PLUG

POWER CORD P/No.

6411FD1096V

6411FR1169B

4.8 19

6411FR1169N

4 9.5 9.5

38.3 1.10.3 18.26

6411FR1169D 6411FR1169P 6411FR1169Q