STARTM 450-315 WIRELESS ACCESS CONTROL RECEIVER
SPECIFICATIONS SUPPLY VOLTAGE: 12-24 VOLTS AC OR DC OPERATING CURRENT: 250 mA MAXIMUM OPERATING TEMP RANGE: -40 TO +149F (-40 TO +65C) FREQUENCY: 315 MHz RELAY CONTACT RATING: 1 AMP @ 24 VOLTS AC OR DC This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Removable memory modules and RF module are included in this product. Jumper J2 must remain in the default position unless otherwise noted. THERE ARE NO OTHER SERVICEABLE PARTS.

TABLE OF CONTENTS

DESCRIPTION PAGE Mounting Instructions for STAR450.1 Programming For STAR450.2-3 Troubleshooting Guide.4 Electrical Connections for STAR450.4 STAR450 Features.4
To prevent possible SERIOUS INJURY or DEATH from electrocution: Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls. Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
MOUNTING INSTRUCTIONS FOR STAR450
Location: Select a convenient location near your device to be controlled by the STAR450. For best performance, the STAR450 should be mounted in Line-Of-Sight with your intended transmitting location. Avoid mounting the STAR450 in or on metallic enclosures. If this is unavoidable, we recommend installing the antenna extension kit (86LM) for best results. See Remote Antenna Mounting for proper installation. Receiver Mounting: Mount back plate to desired surface using #6 hardware (not provided). Hardware used will depend on mounting application (refer to Figure 1 for receiver mounting hole locations). Wire electrical connections to unit. Snap unit to back plate. Direct Antenna Mounting: Install the provided antenna onto the STAR450 antenna connector by screwing the connector clockwise. Slide the seal boot down to meet the O-ring, covering the antenna hardware. Remote Antenna Mounting: Use the optional 86LM antenna extension kit to mount the remote antenna as high and far from metal as possible for best radio range (Figure 2). Contact LiftMaster customer service at: 1-800-528-2806 to order the model 86LM. Figure 1

Antenna Seal Boot

Antenna Connector

Figure 2

STAR450 FEATURES
POWER INDICATOR SCROLLING DASHES ON DIGITAL DISPLAY WHEN AC OR DC POWER IS APPLIED TO THE UNIT.
DIGITAL DISPLAY DISPLAYS REMOTE CONTROL LOCATION NUMBERS WHEN PROGRAMMING OR ACCESS IS GRANTED. ALSO DISPLAYS USER PROMPTS AND MESSAGES.
DELETE KEY USED TO DELETE A REMOTE CONTROL FROM THE SELECTED MEMORY LOCATION
ANTENNA CONNECTION FOR CONNECTION TO THE DIRECT ANTENNA OR THE ANTENNA EXTENSION KIT. BLOCK KEY USED TO BLOCK THE RECEIVER FROM GRANTING ACCESS TO THE SELECTED REMOTE CONTROL. REMOTE CONTROL REMAINS IN MEMORY, AND MAY BE UNBLOCKED IN THE FUTURE.
ADD KEY USED TO ENTER REMOTE CONTROLS AND ENTER RAPID LEARNTM MODE.

Delete

NUMERIC KEYPAD USED FOR PROGRAMMING AND QUERYING REMOTE CONTROL LOCATIONS. ALSO USED TO ENTER ADVANCED FUNCTIONS.
STAR KEY USED TO ENTER ADVANCED FUNCTIONS: , 1- LAST REMOTE CONTROL RECEIVED , 2- NO. OF UNUSED MEMORY LOCATIONS , 3- NO. OF OCCUPIED MEMORY LOCATIONS , 4- NO. OF BLOCKED REMOTE CONTROL LOCATIONS , 5- FIRST BLOCKED REMOTE CONTROL LOCATION , 7- SOFTWARE VER. # , 0- AUDIBLE DIAGNOSTICS OFF/ON
POUND KEY USED AS AN ESC OR EXIT KEY FOR ALL FUNCTIONS OR MODES.

PROGRAMMING THE STAR450

Rapid LearnTM: Add remote control to next available location.

Add PRESS PRESS

TO EXIT
Adding Remote Control: Add remote control to a specific location.

Add PRESS

ENTER LOCATION (1-450)
Deleting a Remote Control: To delete a user.

PRESS TO CONFIRM

PROGRAMMING THE STAR450 (CONTD)
Blocking (Unblocking) a Remote Control: To block or unblock a user.

Block PRESS

Block PRESS TO CONFIRM

END (UNBLOCK)

Duplicating Memory: Allows user to backup programmed remote control memory into the provided backup memory module. Note: If two memory modules are installed, press ,6 to duplicate the memory and remove the backup module.

Main Memory Module

, PRESS SIMULTANEOUSLY

Backup Memory Module

END ~6 SECONDS
Note: To duplicate memory, plug backup memory module into backup slot and press ,6. Once duplication is complete, remove the backup memory module and store in a separate location. Restoring Memory: To restore memory, simply place the duplicate memory module in the main memory position. ADVANCED FUNCTIONS For advanced functions, press and hold the key and a number key at the same time to select the corresponding advanced function. (See table at right for available functions.) Press the # key to exit the function.

* 1 Memory location of last remote control received. * 2 # of open remote control locations. occupied. * 3 # of locationsremote control locations. * 4 # of blocked remote location. First blocked * Next blocked location (Repeat to scroll). * 6 Duplicate memory- See Duplicating memory. * # 7 Version #exit functions. Press to *
0 Audible diagnostics OFF/ON (LED will be displayed when OFF) If no remote controls are programmed into the star450, then (---) will be displayed.
AUDIBLE DIAGNOSTICS Step 1. Activate remote control. Step 2. Listen for beep. (LED will be displayed when OFF)
Double Beep: Remote control is valid and programmed into STAR450 accompanied by remote control location display. Slow Beep: Security+ Remote control (Not programmed in STAR450). Long Beep: Blocked remote control. No Beep: Remote control not working.
KEYPAD SOUND ALERTS Single Beep: Key pressed. Double Beep: Confirmation of an accepted Tx or valid add/block input.

Display OPn Occ bLc Out

Triple Beep: Confirmation of delete.
Long Beep: Blocked Tx, error, or out of range
Description Remote control location is empty Remote control location is occupied Remote control location is blocked Remote control location is out of range(not between 1 & 450) Beeper no beep no beep no beep long beep
REMOTE CONTROL LOCATION QUERY Enter a remote control location number (001-450) to view location status (see table to the right for possible status displays). 3

TROUBLESHOOTING GUIDE

Problem

No display

Probable Cause(s)
1. Faulty/intermittent power connections to unit Or 2. No power to unit Audible diagnostics may have been turned OFF (right-most decimal point will be lit on the display) 1. Transmitter not learned into system Or 2. Transmitter is blocked Or 3. Transmitter battery is dead 1. Memory may be full Or 2. Transmitter may not be a recognized Chamberlain transmitter Or 3. Transmitter battery is dead

Solution(s)

1. Check power connections to unit 2. Supply power to unit Press 4 and 0 keys at the same time 1. Add transmitter to memory 2. Replace transmitter battery 1. Delete unused transmitters from memory 2. Verify transmitter is listed in compatible transmitters section Or 3. Replace transmitter battery Replace main memory module Replace backup memory module
No beep when transmitting Transmitter does not activate operator Transmitter will not learn into memory
Unit does not function, Main memory module missing or [E 1] displayed damaged Duplication function does not work, [E 2] displayed Keypad does not respond, [E 3] displayed Backup memory module missing or damaged, if included Keypad has a stuck key
Cycle power. If unit exhibits this condition again after 2 minutes, contact Technical Service.
ELECTRICAL CONNECTIONS FOR STAR450
Receiver (Bottom) Wall Button Receiver (Bottom) Wall Button Opener Trans Primary Trans Primary

Model 85 Transformer To wall outlet
To wall Model 95 outlet Transformer
STAR450 COMPATIBLE REMOTE CONTROLS
Security+ Remote Controls
373P 371LM 372LM 370LM 373LM 374LM
STAR 450 OPTIONAL ACCESSORIES

CGI Part Number

71-65WTBOX 86LM 85LM 95LM

Security+ Keypads

377LM 379LM

Description

Watertight Box Field Install Kit Antenna Extension Kit 24VAC Transformer with Barrel Connector 24VAC Transformer with Screw Terminals

Passport Remote Control

CPT43 CPT13 CPT23 CPT33

Digital Remote Controls

361LM 362LM 363LM 333LM
SERVICE INFORMATION TOLL FREE NUMBER 1-800-528-2806

www.liftmaster.com

Passport Mini Remote Control
CPTK13 CPTK13PH CPTK33 CPTK33PH For highest level of security, we recommend the Security+ and Passport transmitter families.

114A3254C

2007, The Chamberlain Group, Inc. All Rights Reserved

Access Control Devices

Part LM312HM LM361LM LM370LM LM371LM LM372LM LM373LM LM374LM LM375LM Description 12/24 Volt High Memory Universal Coaxial Receiver Single Button Transmitter Three Button Mini-Transmitter (Sec. +) Single Button Transmitter (Sec. +) Double Button Transmitter (Sec.+) Three Button Transmitter (Sec. +) Four Button Transmitter (Sec. +)
Universal Transmitter Compatible with the following brands Genie, Linear/Moore-o-Matic, Stanley, Overhead Door, Wayne-Dalton, Craftsman, Chamberlain, LiftMaster.
Switches None 9 None None None None None Yes Freq. 315
300, 310, 315, 372, 390 MHz
LiftMaster Brand Access Devices Freq. 315 & 390 MHz
LM412HM LM61LM LM62LM LM81LM LM82LM LM970LM LM971LM LM972LM LM973LM LM974LM
12/24 Volt High Memory Universal Coaxial Receiver Single Button Transmitter Double Button Transmitter Single Button Transmitter Double Button Transmitter Three Button Mini-Transmitter (Sec. +) Single Button Transmitter (Sec. +) Double Button Transmitter (Sec.+) Three Button Transmitter (Sec. +) Four Button Transmitter (Sec. +)
None None None None None None None None

390 390

GENIE Brand Access Devices Freq. 390 MHz
All transmitters are self contained and include a battery. It is supplied with a clip for a sun visor. Approx. 50 ft range depending on battery strength. Part GENMAT90 GENGPT90-1 GENGT912 GENGPT90-3 GENGR390-12 Description Mini Single Button Transmitter Single Button Transmitter Single Button 9/12 Switch Transmitter Three Button Transmitter 24 Volt Receiver Switches 9/12 Freq. 390
GENIE Intellicode Brand Access Devices Freq. 390 MHz
All transmitters are self contained and include a battery. It is supplied with a clip for a sun visor. Approx. 50 ft range depending on battery strength. The Genie Intellicode system changes access codes automatically after each use up to 4.3 billion code combinations available.
Part GENGMIC90-3 GENGIT-1 GENGIT-2 GENGIT-3 GENGIR390
Description Mini Three Button Transmitter Single Button Transmitter Double Button Transmitter Three Button Transmitter 24 Volt Receiver
Switc hes None None None None None

Freq. 390

Jansen Ornamental Supply Co. El Monte, Ca. 800-423-4494 www.jansensupply.com
Multi-Code Brand Access Devices Freq. 300 MHz
Part MINITRNS DBMINITRNS TRNS DBTRNS 4BTRNS REC12/24LR REC24 REC24HARNESS RECANTLR Description Micro Single Button Transmitter Mini Double Button Transmitter Single Button Transmitter Double Button Transmitter Four Button Transmitter Long Range 12/24 Volt Receiver 24 Volt Receiver Wiring Harness For 24V Receiver Antenna W/Coax For Long Range Receiver 15 ft Long Switches 10 N/A N/A Freq. 300 N/A N/A
The Multi-Code brand is preferred among so many installers of gate operators and systems, garage door operators, and commercial access control systems.
Linear Delta 3 Brand Access Devices Freq. 310 MHz
Our popular Delta 3 line offers 256 codes and a 310 MHz frequency, which is ideal for most sites. Part LINMINI-T LINDT LINDT-2A LINDT-4A LINGRD Description Mini Single Button Transmitter Single Button Transmitter Double Button Transmitter Four Button Transmitter Long Range 12/24 Volt Receiver W/Coax Connect & Small Antenna Switches 8 Freq. 310
STAR450-315 Wireless Access Control Receiver
Receiver For Gate and Commercial Operators And Residential Garage Door Openers
The Lift-Master Star450 Access Control Receiver is a compact, easy to program receiver designed for gate operators, commercial door operators and residential garage door openers. The Star450 is compatable with all Security+ and billion code openers from Lift-Master. The user-friendly digital display and numeric keypad uses prompts and messages for easy programming to add, block and delete up to 450 transmitters individually. Block key allows certain transmitters to be blocked from memory and may be unblocked in the future. Uses 12-24 volts AC or DC supply voltage. Can be mounted in an existing control box or optional weather-proof accessory box.

3 Button Station PBS-3

OPEN / CLOSE / STOP Allows Complete Control of Gate
Indoor Surface Mount This 3 Button Station may require additional harnesses to work properly with various gate operators.
Optional External Watertight Enclosure Kit For STAR450-315 Field Box
7-1/2 W. X 10 H. X 3-3/8 D.
Mini Board needed to hook up to the Elite Commercial Operators.
Harness for the Miracle1 Operator

LM71-65WT

LMSTAR450
4-3/8 W. X 5-5/8 H. X 1-1/2 D.
2-3/8 W. X 5-3/8 H. X 1-3/4 D.

OMNI-EXB