Internet Phone Adapter
with 2 Ports for Voice-over-IP

User Guide

Model No.
Internet Phone Adapter with 2 Ports for Voice-over-IP

Copyright and Trademarks

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. WARNING: This product contains chemicals, including lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

How to Use this Guide

Your guide to the Internet Phone Adapter has been designed to make understanding networking with the Internet Phone Adapter easier than ever. Look for the following items when reading this User Guide: This checkmark means there is a note of interest and is something you should pay special attention to while using the Phone Adapter. This exclamation point means there is a caution or warning and is something that could damage your property or the Phone Adapter. This question mark provides you with a reminder about something you might need to do while using the Phone Adapter. In addition to these symbols, there are definitions for technical terms that are presented like this: word: definition. Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like this: Figure 0-1: Sample Figure Description
Figure numbers and descriptions can also be found in the List of Figures section.

PAP2T-UG-60807NC LH

Table of Contents

Chapter 1: Introduction

... Welcome. Whats in this Guide?. Chapter 2: Getting to Know the Phone Adapter. The Back Panel. The Front Panel. Chapter 3: Connecting the Phone Adapter. Overview. Connecting the Phone Adapter. 5
Chapter 4: Using the Phone Adapters Interactive Voice Response Menu.
7 Overview. 7 Accessing the Interactive Voice Response Menu. 7 Using the Interactive Voice Response Menu. 8 Entering a Password. 12 Configuring the Settings for Your Internet Phone Service. 12 Appendix A: Troubleshooting. 13 Common Problems and Solutions. 13 Frequently Asked Questions. 16 Appendix B: Glossary. 17
Appendix C: Specifications. Appendix D: Warranty Information. Appendix E: Regulatory Information. Appendix F: Contact Information.
33 Internet Phone Service Provider. 33 Linksys. 33
Analog Telephone Adapter with 2 FXS Ports

List of Figures

Figure 2-1: Back Panel. Figure 2-2: Front Panel. Figure 3-1: Connection Diagram of a Typical Setup. Figure 3-2: Connect the RJ-11 Telephone Cable. Figure 3-3: Connect the Ethernet Network Cable. Figure 3-4: Connect the Power Adapter. 6 6

Welcome

Thank you for choosing the Linksys Internet Phone Adapter with 2 Ports for Voice-over-IP. This Phone Adapter will allow you to make phone or fax calls using your broadband connection. How does the Phone Adapter do this? Plug the Phone Adapter into your network router or gateway, then connect your phones or fax machines to the Phone Adapter. Each of the Phone Adapters two telephone jacks operate independently, with separate Internet phone services and phone numbers, so you can have up to two Internet phone lines delivered through your cable or DSL Internet connection. What does all of this mean? The Phone Adapter allows your phones or fax machines to take advantage of and share your high-speed Internet connection. You can even make phone calls while youre surfing the Internet (Internet phone services required). Refer to the instructions in the Quick Installation or this User Guide to help you connect the Phone Adapter after you have set up an account with your Internet phone service provider. The instructions in this User Guide will help you get the most out of your Phone Adapter.

INTERNET

PHONE 1/2
Chapter 3: Connecting the Phone Adapter

Overview

This chapter explains how to connect the Phone Adapter to your network and telephones or fax machines. Shown below is a connection diagram displaying a typical setup.

Internet

Cable/DSL Modem

Router

Phone Adapter

Telephone

Figure 3-1: Connection Diagram of a Typical Setup
Connecting the Phone Adapter
If you already have an account set up with your Internet phone service provider, then proceed to step 1. If you do not have an account set up with your Internet phone service provider, then go to your providers website and sign up for service. After you have set up an account, proceed to step 1. 1. Using a telephone cable, connect your telephone to the PHONE 1 port of the Phone Adapter. 2. If you have a second Internet phone service account, connect another telephone or a fax machine to the PHONE 2 port of the Phone Adapter.
IMPORTANT: The Phone Adapter includes a ringer (ring signal generator), which is a source of hazardous voltage. When the ringer is activated by an incoming call, do not touch the Phone port wires, the wires of a cable connected to either of the Phone ports, or the internal circuitry of the Phone Adapter. IMPORTANT: Do not connect either of the Phone ports to a telephone wall jack. Make sure you only connect a telephone or fax machine to either of the Phone ports. Otherwise, the Phone Adapter or the telephone wiring in your home or office may be damaged.
Figure 3-2: Connect the RJ-11 Telephone Cable
Chapter 3: Connecting the Phone Adapter Overview
3. Connect the included Ethernet network cable to the INTERNET port of the Phone Adapter. Connect the other end to one of the Ethernet ports on your router or gateway. 4. Connect the included power adapter to the POWER port on the back panel of the Phone Adapter. Connect the other end to a standard electrical outlet. 5. The Status and Act LEDs will be solidly lit when the Phone Adapter is ready for use. 6. Follow the instructions provided by your Internet phone service provider. If you need to manually configure the Phone Adapters network settings, you can use the telephone connected to the Phone Adapter. See Chapter 4: Using the Phone Adapters Interactive Voice Response Menu for instructions. The installation of the Phone Adapter is complete. Now you can pick up your phone and make calls. Figure 3-3: Connect the Ethernet Network Cable

Figure 3-4: Connect the Power Adapter
Chapter 3: Connecting the Phone Adapter Connecting the Phone Adapter
Chapter 4: Using the Phone Adapters Interactive Voice Response Menu
You may need to manually configure the Phone Adapter by entering the settings provided by your Internet phone service provider. This chapter explains how to use the Interactive Voice Response Menu to configure the Phone Adapters network settings. You will use the phones keypad to enter your commands and select choices, and the Phone Adapter will respond with voice responses. NOTE: If your Internet phone service provider sent you the Phone Adapter, then it may be pre-configured for you, and you may not need to change any settings. Refer to the instructions provided by your service provider for more information.
Accessing the Interactive Voice Response Menu
1. Use a telephone connected to the PHONE 1 or PHONE 2 port of the Phone Adapter. 2. Press the * (star) key four times. 3. Wait until you hear Configuration menu. Please enter option followed by the # (pound) key or hang up to exit. 4. Refer to the table on page 8 for a list of actions, commands, menu choices, and descriptions. After you select an option, press the # (pound) key. To exit the menu, hang up the telephone.
Chapter 4: Using the Phone Adapters Interactive Voice Response Menu Overview
Using the Interactive Voice Response Menu
When entering values, such as an IP address, you may exit without saving your changes by press the * (star) key twice within half a second. Otherwise, the * (star) key will be treated as a decimal point or dot. After entering a value, such as an IP address, press the # (pound) key to indicate you have finished your selection. To save the new setting, press the 1 key. To review the new setting, press the 2 key. To re-enter the new setting, press the 3 key. To cancel your entry and return to the main menu, press the * (star) key. For example, to enter the IP address 191.168.1.105 using your telephones keypad, press: 191*168*1*105. When you are finished, press the # (pound) key, then press the 1 key to save the IP address. To cancel your entry and return to the main menu, press the * (star) key. If the menu is inactive for more than one minute, the Phone Adapter will automatically exit the Interactive Voice Response Menu. To re-enter the menu, press the * (star) key four times. The settings you have saved will take effect when you hang up the telephone. The Phone Adapter may reboot at this time.

Interactive Voice Response Menu
Action Command (press these keys on the telephone)

Choices

Description
Enter Interactive Voice Response Menu
Use this command to enter the Interactive Voice Response Menu. Do not press any other keys until you hear, Configuration menu. Please enter option followed by the # (pound) key or hang up to exit. Use this command to find out if DHCP has been enabled or disabled. If it is enabled, the Phone Adapter will be assigned an IP address automatically by your network router or gateway. If it is disabled, then the Phone Adapter will need to use a static IP address.

Check DHCP

Chapter 4: Using the Phone Adapters Interactive Voice Response Menu Using the Interactive Voice Response Menu

Enable/Disable DHCP

Enter 1 to enable Enter 0 to disable
Enable or disable the Phone Adapters DHCP feature. If your network router assigns IP addresses, enter 1, otherwise, enter 0. Use this command to check the current IP address of the Phone Adapter. To set a static IP address, the DHCP feature must be disabled. If the DHCP feature is enabled, you will hear, Invalid Option, if you try to set a static IP address. Use this command to check the current network mask of the Phone Adapter. To set the network mask, the DHCP feature must be disabled. If the DHCP feature is enabled, you will hear, Invalid Option, if you try to set the network mask. Use this command to check the current gateway IP address of the Phone Adapter. To set a static gateway IP address, the DHCP feature must be disabled. If the DHCP feature is enabled, you will hear, Invalid Option, if you try to set a static gateway IP address.

Check IP Address

Set Static IP Address
Enter the IP address using the numbers on your telephone keypad. Use the * (star) key to enter a decimal point.
Check Network Mask (or Subnet Mask) Set Network Mask (or Subnet Mask)
Enter the network mask using numbers on your telephone keypad. Use the * (star) key to enter a decimal point.
Check Static Gateway IP Address Set Static Gateway IP Address
Enter the IP address using numbers on your telephone keypad. Use the * (star) key to enter a decimal point.

Check MAC Address

Use this command to check the current MAC address of the Phone Adapter in hexadecimal string format. Use this command to check the current version number of the firmware currently installed on the Phone Adapter. This feature is password protected by your Internet phone service provider. (The Web-based Utility is disabled by default because you will not need to use it unless instructed to do so by your service provider.) If you have been provided a password, see Entering a Password.

Check Firmware Version

Enable/Disable Webbased Utility of Phone Adapter

Manual Reboot

732668
After you hear, Option successful, hang up the phone. The Phone Adapter will automatically reboot.

Factory Reset

Enter 1 to confirm Enter * (star) to cancel
This feature is password protected by your Internet phone service provider. (You will not need to reset the Phone Adapter to its factory default settings unless instructed to do so by your service provider.) If you have been provided a password, see Entering a Password. After you have entered your password, the Phone Adapter will request confirmation. After confirmation, you will hear, Option successful. Hang up the phone. The Phone Adapter will reboot and all settings will be reset to their factory default settings.

Entering a Password

You will be prompted to enter a password if you want to enable the Web-based Utility or reset the Phone Adapter to its factory default settings. To enter a password, use the phones keypad, and follow the appropriate instructions. To enter A, B, C, a, b, or c press the 2 key. To enter D, E, F, d, e, or f press the 3 key. To enter G, H, I, g, h, or i press the 4 key. To enter J, K, L, j, k, or l press the 5 key. To enter M, N, O, m, n, or o press the 6 key. To enter P, Q, R, S, o, q, r, or s press the 7 key. To enter T, U, V, t, u, or v press the 8 key. To enter W, X, Y, Z, w, x, y, or z press the 9 key. To enter all other characters, press the 0 key. NOTE: These bulleted instructions above only apply when you are entering a password. Pressing a number at all other times selects only a number, not a letter or punctuation mark. For example, to enter the password phone@321 by keypad, press: 746630321. When you are finished, press the # (pound) key. To cancel your entry and return to the main menu, press the * (star) key.

Configuring the Settings for Your Internet Phone Service
If you want to change the settings for your Internet phone service, visit your Internet phone service providers website and make configuration changes online. For more information, refer to the instructions provided by your Internet phone service provider.
Chapter 4: Using the Phone Adapters Interactive Voice Response Menu Entering a Password
Appendix A: Troubleshooting
This appendix provides solutions to problems you may experience when installing and using the Phone Adapter. Read the descriptions below to solve your problems. If you can't find an answer here, check your Internet phone service providers website.
Common Problems and Solutions
1. I dont hear a dial tone. Go through this checklist until your problem is solved: Make sure the telephone is plugged into the correct port, PHONE 1 or PHONE 2. (You should use the Phone 2 port only if you have more than one Internet telephone service account.) Make sure the green INTERNET LED on the front panel of the Phone Adapter is lit. If it is not lit, check your router and network connection to the Internet. Make sure the green PHONE 1 LED on the front panel of the Phone Adapter is lit, then pick up the telephone; you should now have a dial tone. Follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router: 1. Power off your cable or DSL modem by unplugging its power adapter. 2. Power off the router by unplugging its power adapter. 3. Power off the Phone Adapter by unplugging its power adapter. 4. Wait two minutes, then power on your cable or DSL modem by plugging its power adapter into an electrical outlet. 5. Wait two minutes, then power on the router by plugging its power adapter into an electrical outlet. 6. Wait five minutes, then power on the Phone Adapter by plugging its power adapter into an electrical outlet. 7. Reboot one of your networked computers, and check to see if you have an active Internet connection. 8. Pick up the telephone. You should now have a dial tone. Set up port forwarding on your router. You must specify that ports 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP) are forwarded to the IP address of the Phone Adapter. Before you set up port forwarding on your router, change two of the Phone Adapters settings using its Interactive Voice Response Menu. First, disable its DHCP feature, then assign a static IP address to the Phone Adapter. See Chapter 4: Using the Interactive Voice Response Menu for instructions.
Appendix A: Troubleshooting Common Problems and Solutions
2. When I make a telephone call, the call doesnt go through; instead, I hear a fast busy signal. Go through this checklist until your problem is solved: Follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router: 1. Power off your cable or DSL modem by unplugging its power adapter. 2. Power off the router by unplugging its power adapter. 3. Power off the Phone Adapter by unplugging its power adapter. 4. Wait two minutes, then power on your cable or DSL modem by plugging its power adapter into an electrical outlet. 5. Wait two minutes, then power on the router by plugging its power adapter into an electrical outlet. 6. Wait five minutes, then power on the Phone Adapter by plugging its power adapter into an electrical outlet. 7. Reboot one of your networked computers, and check to see if you have an active Internet connection. 8. Pick up the telephone. You should now have a dial tone. Set up port forwarding on your router. You must specify that ports 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP) are forwarded to the IP address of the Phone Adapter. Before you set up port forwarding on your router, change two of the Phone Adapters settings using its Interactive Voice Response Menu. First, disable its DHCP feature, then assign a static IP address to the Phone Adapter. See Chapter 4: Using the Interactive Voice Response Menu for instructions.

3. When Im on a telephone call, words are dropped intermittently. Go through this checklist until your problem is solved: If youre using a wireless router and a cordless phone, they may be using the same frequency and may interfere with each other. Move the cordless phone farther away from the router. There may be heavy network activity, particularly if you are running a server or using a file sharing program. Try to limit network or Internet activity during Internet telephone calls. For example, if you are running a file sharing program, file may be uploaded in the background even though you are not downloading any file, so make sure you exit the program before making Internet phone calls. There may not be enough bandwidth available for your Internet phone call. You may want to test your bandwidth using one of the bandwidth tests available online. If necessary, access your Internet phone service account and reduce the bandwidth requirements for your service. For more information, refer to your service providers website.
4. My telephone does not ring, and my calls automatically go to voicemail. Go through this checklist until your problem is solved: Make sure the telephone is plugged into the correct port, PHONE 1 or PHONE 2. (You should use the Phone 2 port only if you have more than one Internet telephone service account.) Make sure the ringer volume on your telephone is set to an audible level. Follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router: 1. Power off your cable or DSL modem by unplugging its power adapter. 2. Power off the router by unplugging its power adapter. 3. Power off the Phone Adapter by unplugging its power adapter. 4. Wait two minutes, then power on your cable or DSL modem by plugging its power adapter into an electrical outlet. 5. Wait two minutes, then power on the router by plugging its power adapter into an electrical outlet. 6. Wait five minutes, then power on the Phone Adapter by plugging its power adapter into an electrical outlet. 7. Reboot one of your networked computers, and check to see if you have an active Internet connection. Set up port forwarding on your router. You must specify that ports 5060-5061 (UDP), 53-53 (UDP), 69-69 (UDP), and 10000-20000 (UDP) are forwarded to the IP address of the Phone Adapter. Before you set up port forwarding on your router, change two of the Phone Adapters settings using its Interactive Voice Response Menu. First, disable its DHCP feature, then assign a static IP address to the Phone Adapter. See Chapter 4: Using the Interactive Voice Response Menu for instructions.
5. The INTERNET LED does not light up. Go through this checklist until your problem is solved: Check the cable connecting the Phone Adapter to your router. Make sure your network has an active Internet connection. If it does not, follow these instructions to reboot your cable or DSL modem, Phone Adapter, and router: 1. Power off your cable or DSL modem by unplugging its power adapter. 2. Power off the router by unplugging its power adapter. 3. Power off the Phone Adapter by unplugging its power adapter. 4. Wait two minutes, then power on your cable or DSL modem by plugging its power adapter into an electrical outlet. 5. Wait two minutes, then power on the router by plugging its power adapter into an electrical outlet. 6. Wait five minutes, then power on the Phone Adapter by plugging its power adapter into an electrical outlet. 7. Reboot one of your networked computers, and check to see if you have an active Internet connection.

Frequently Asked Questions
How do I make a phone call? Pick up your phone and dial a phone number. Some Internet phone service providers may require specific dialing instructions. Please check with your Intenet phone service provider for details. Can I make calls if my Internet connection is down? No. Your high-speed Internet connection must be active when you make Internet phone or fax calls. Can I make calls while Im browsing the Internet? Yes. You can make Internet phone or fax calls while browsing the Internet, however, upstream data traffic passing through your Internet connection may affect the quality of your telephone call.
Appendix A: Troubleshooting Frequently Asked Questions

Appendix B: Glossary

This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Access Point - A device that allows wireless-equipped computers and other devices to communicate with a wired network. Also used to expand the range of a wireless network. Ad-hoc - A group of wireless devices communicating directly with each other (peer-to-peer) without the use of an access point. AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Broadband - An always-on, fast Internet connection. Browser - An application program that provides a way to look at and interact with all the information on the World Wide Web. Byte - A unit of data that is usually eight bits long Cable Modem - A device that connects a computer to the cable television network, which in turn connects to the Internet. Daisy Chain - A method used to connect devices in a series, one after the other. DDNS (Dynamic Domain Name System) - Allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (e.g., www.xyz.com) and a dynamic IP address. Default Gateway - A device that forwards Internet traffic from your local area network. DHCP (Dynamic Host Configuration Protocol) - A networking protocol that allows administrators to assign temporary IP addresses to network computers by "leasing" an IP address to a user for a limited amount of time, instead of assigning permanent IP addresses.
DMZ (Demilitarized Zone) - Removes the Router's firewall protection from one PC, allowing it to be "seen" from the Internet. DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines. Dynamic IP Address - A temporary IP address assigned by a DHCP server. EAP (Extensible Authentication Protocol) - A general authentication protocol used to control network access. Many specific authentication methods work within this framework. Encryption - Encoding data transmitted in a network. Ethernet - IEEE standard network protocol that specifies how data is placed on and retrieved from a common transmission medium. Firewall - A set of related programs located at a network gateway server that protects the resources of a network from users from other networks. Firmware - The programming code that runs a networking device. FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP network. Full Duplex - The ability of a networking device to receive and transmit data simultaneously. Gateway - A device that interconnects networks with different, incompatible communications protocols. Half Duplex - Data transmission that can occur in two directions over a single line, but only one direction at a time. HTTP (HyperText Transport Protocol) - The communications protocol used to connect to servers on the World Wide Web. Infrastructure - A wireless network that is bridged to a wired network via an access point. IP (Internet Protocol) - A protocol used to send data over a network.

TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. Topology - The physical layout of a network. TX Rate - Transmission Rate. Upgrade - To replace existing software or firmware with a newer version. Upload - To transmit a file over a network. URL (Uniform Resource Locator) - The address of a file located on the Internet. VPN (Virtual Private Network) - A security measure to protect data as it leaves one network and goes to another over the Internet. WAN (Wide Area Network)- The Internet. WEP (Wired Equivalent Privacy) - A method of encrypting network data transmitted on a wireless network for greater security. WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly. WPA (Wi-Fi Protected Access) - a wireless security protocol using TKIP (Temporal Key Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.
Appendix C: Specifications
Model Standards Voice Codecs Ports Cabling Type LEDs PAP2T SIP v2 Session Initiation Protocol v2 (RFC 3261, 3262, 3263, 3264) G.729 A, G.711 a-law, G.711-law, G.726, G.723.1 Power, Internet, Phone 1, Phone 2 CAT 5 (RJ45) for Ethernet Port and RJ11 for Phone Ports Power, Internet, Phone 1, Phone 2
Maximum Ringer Load 3 REN Ring Frequency FXS Port Impedance Ring Voltage Security Features Dimensions (W x H x D) Unit Weight Power Certifications Operating Temp.
10-40 Hz Eight Configurable Settings Including North America 600 ohms, European CTR21 40-55 Vrms Configurable Password Protected Administration 3.98" x 3.98" x 1.1" (101mm x 101mm x 28mm) 5.4 oz. (0.15 kg) 5 V DC, 2.0 A FCC, CE Mark 32~113F (0~45C)
Storage Temp. Operating Humidity Storage Humidity
-77~158F (-25~70C) 10~90% Non-Condensing 5~90% Non-Condensing
Appendix D: Warranty Information

LIMITED WARRANTY

Your service provider warrants to You that, for a period of one year (the Warranty Period), your Linksys Product will be substantially free of defects in materials and workmanship under normal use. Your exclusive remedy and your service providers entire liability under this warranty will be for your service provider at its option to repair or replace the Product or refund Your purchase price less any rebates. This limited warranty extends only to the original purchaser. If the Product proves defective during the Warranty Period call your service providers Technical Support in order to obtain a Return Authorization Number, if applicable. BE SURE TO HAVE YOUR PROOF OF PURCHASE ON HAND WHEN CALLING. If You are requested to return the Product, mark the Return Authorization Number clearly on the outside of the package and include a copy of your original proof of purchase. RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF PURCHASE. You are responsible for shipping defective Products to your service provider. Your service provider pays for UPS Ground shipping from your service provider back to You only. Customers located outside of the United States of America and Canada are responsible for all shipping and handling charges. ALL IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to You. This warranty gives You specific legal rights, and You may also have other rights which vary by jurisdiction. This warranty does not apply if the Product (a) has been altered, except by your service provider, (b) has not been installed, operated, repaired, or maintained in accordance with instructions supplied by your service provider, or (c) has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident. In addition, due to the continual development of new techniques for intruding upon and attacking networks, your service provider does not warrant that the Product will be free of vulnerability to intrusion or attack. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT WILL YOUR SERVICE PROVIDER BE LIABLE FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN IF YOUR SERVICE PROVIDER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT WILL YOUR SERVICE PROVIDERS LIABILITY EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT. The foregoing limitations will apply even if any warranty or remedy provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to your service provider.

Appendix E: Regulatory Information
FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment or devices Connect the equipment to an outlet other than the receiver's Consult a dealer or an experienced radio/TV technician for assistance
FCC Part 68 Statement This equipment complies with Part 68 of the FCC Rules. A label is attached to the equipment that contains, among other information, its FCC registration number and ringer equivalence number. If requested, this information must be provided to the telephone company. This equipment uses the following USOC Jack: RJ-11. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack, which is FCC Part 68 compliant. Connection to the telephone network should be made by using the standard modular telephone jack. The REN is useful to determine the quantity of devices that may be connected to the telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of RENs should not exceed 5. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area. If this equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If advance notice is not practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service. In the event this equipment should fail to operate properly, disconnect the unit from the telephone line. Try using another FCC approved device in the same telephone jack. If the trouble persists, call the telephone company repair service bureau. If the trouble does not persist and appears to be with this unit, disconnect the unit from the telephone line and discontinue use of the unit until it is repaired. Please note that the telephone company may ask that you disconnect the equipment from the telephone network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. The user must use the accessories and cables supplied by the manufacturer to get optimum performance from the product. No repairs may be done by the customer. If trouble is experienced with this equipment, please contact your authorized support provider for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved. This equipment cannot be used on telephone company provided coin service. Connection to Party Line Service is subject to state tariffs. Safety Notices Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Industry Canada (Canada) This device complies with Industry Canada ICES-003 rule. Cet appareil est conforme la norme NMB003 d'Industrie Canada. IC Statement Operation is subject to the following two conditions: 1. This device may not cause interference and 2. This device must accept any interference, including interference that may cause undesired operation of the device.
Rglement dIndustry Canada Le fonctionnement est soumis aux conditions suivantes : 1. Ce priphrique ne doit pas causer d'interfrences; 2. Ce priphrique doit accepter toutes les interfrences reues, y compris celles qui risquent d'entraner un fonctionnement indsirable. User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:

For more information, visit www.linksys.com.
Appendix F: Contact Information
Internet Phone Service Provider
Contact your service provider if the warranty support issues are to be handled by them as per your service agreements.

Linksys

Visit Linksys online for information on the latest products and updates for your existing products at: http://www.linksys.com
Appendix F: Contact Information Internet Phone Service Provider

LinksysPAP2TNA Setup

User Guide
Version1.0 Updated 5/2/2008
Overview This guide provides an overview of setting up the Linksys PAP2T-NA device. General Support If you have questions or need technical assistance with Evolution PBX call (888) 587-5750 or send an Email to support@intuitivevoice.com. If you have questions about third party hardware or software please visit the following Websites: Snap: http://www.snapanumber.com. iView: http://www.i9technologies.com/. Cisco VoIP Telephones: http://www.cisco.com. CounterPath Software Telephones - http://www.counterpath.com. Digium PCI Cards: http://www.digium.com. Linksys Analog Terminal Adapters and VoIP telephones: http://www.linksys.com. Polycom VoIP Telephones: http://www.polycom.com.
My Evolution PBX Doesnt Do That! Some features and configuration options in this document may only be available with a recent software upgrade available from Intuitive Voice Technology. Email support@intuitivevoice.com to learn more about Evolution PBX upgrades (please explain the feature that you are interested in). Errata Please report errors or confusing descriptions by sending an Email to support@intuitivevoice.com.

Page 2 of 4

SettingUptheLinksysPAP2TNA
The Linksys PAP2T-NA is a SIP analog terminal adapter. It has one RJ45 Ethernet interface to connect to your data network and two RJ11 FXS interfaces to connect to analog devices such as analog telephones or fax machines. Each analog port on the PAP2T-NA must be configured as an individual extension in Evolution PBX.
ConfiguringthePAP2TNAinEvolutionPBX
To Configure a Basic Extension for the PAP2T-NA in Evolution PBX 1. Login to Evolution PBX, click the Resources tab then click Phone Extensions. 2. In the New Device field, select VoIP--GENERIC SIP and the Modify Phones window displays. 3. In the Extension field, select an available extension. 4. In the Caller ID Name field, enter the name you want to be passed as this extensions caller ID text. 5. In the Caller ID Number field, enter the number you want to be passed as this extensions caller ID number. 6. In the Time Zone field, select the appropriate time zone for the time zone where the phone will be located. 7. In the Remote Phone field, select Yes if the phone will not be on the same subnet as the Evolution PBX server (for example, if the phone belongs to a user that is located at a remote location). Select No if this is not the case. Note: The other options on the Modify Phones frame are optional or advanced. 8. Click Save. Note: The Evolution PBX Web configuration interface requires that your browsers popup blocker be turned off or disabled so that the Device Settings screen can be seen. 9. Write down the device settings for your new extension that are displayed on the screen. These settings will be used to configure your phone.

Page 3 of 4

ConfiguringtheLinksysPAP2TNAAdaptor
To Configure the Linksys PAP2T-NA Adaptor 1. Connect the Linksys PPAP2T-NA to your Ethernet network then connect an analog telephone to one of the ports labeled PHONE 1 or PHONE 2. 2. Dial **** on your analog phone, enter 110# and the IP Address the Linksys PAP2T-NA adaptor acquired from your network is given. 3. Write down the IP Address, open a Web Browser then enter the IP Address (for example, http://192.168.2.71) into the Address bar. 4. Press Enter and the Info tab of the Linksys Telephone Configuration window displays. 5. Click Admin Login, click switch to advanced view then click Line 1 to configure the SIP settings. 6. In the Line Enable field, select yes. 7. In the SIP Port field, enter 5060. 8. In the Proxy field enter Evolution PBXs IP Address (for example, 192.168.165.100). 9. In the Register field, select yes. 10. In the User ID field, enter the extension number (for example, 1020) 11. In the Password field, enter the password provided by Evolution PBX you wrote down when you created your default extension. 12. In the Use Auth ID field, select No. 13. Click Save Settings and the telephone will save, reboot, and automatically register with Evolution PBX.

Page 4 of 4