Service Manual for LK2 Series of Power Amps
Covering LK2(60), LK275 & LK280
For the purposes of this manual, we will refer to the three types as LK260, LK275 & LK280. The term LK2 will be used as an umbrella term, covering all three types, i.e. the LK2 series.

CONTENTS

INTRODUCTION.... 2 ABOUT THE LK2 SERIES.... 2 HOW TO DIFFERENTIATE BETWEEN TYPES OF LK2.... 2 ABOUT THIS MANUAL.... 3 R ETAILER & D ISTRIBUTOR OBLIGATIONS.... 3 SPARE PARTS AVAILABILITY AND LK2 REPAIR.... 3 HOW TO USE THIS MANUAL..... 3 IMPORTANT SAFETY INFORMATION & INSTALLATION ADVICE.. 4 MAINS CONNECTIONS..... 4 L ETHAL VOLTAGES.... 4 PLACEMENT..... 4 PROCEDURE FOR DISMANTLING AND RE-ASSEMBLING THE LK2... 5 FAULT FINDING ON THE LK2 HINTS & TIPS... 9 POWER-UP PROBLEMS FAULT TABLE....10 W ONT POWER UP....10 W ONT SWITCH OFF....10 FUSE BLOWING.....11 AMPLIFIER PROBLEMS FAULT TABLE....13 NO OUTPUT.....13 TRIP ( PROTECTION ) PROBLEMS....15 D ISTORTION / CRACKLING ETC....16 DC AT OUTPUT.....17
Copyright 2000 Linn Products Limited. All rights reserved. Paul O'Neill

LK2 Service Manual

Introduction

About the LK2 Series

There were three versions of the LK2: The first version was known at the time simply as the LK2. It gave an output of 60 watts per channel (into 8 ohm load) and used PCAS 003 type boards. For the purposes of this manual, we will refer to this version as the LK260. The second type was also usually known as the LK2 but was often called the LK275 to differentiate it from the 60-watt version, as it gave 75 watts per channel. Also used PCAS 003 type boards but with several improvements over the 60 watt version the most obvious being the increased power output, but also had improved protection circuitry and better sound. The third and last type was known universally as the LK280. 80 watts per channel used PCAS 020 boards. PCAS 020s, at first glance are similar to PCAS 003s, in that they are roughly the same size, shape and layout, but they are a completely different design of board (i.e. not just a modified version of PCAS 003) as a closer examination shows. The LK280 sounded considerably better than either of its predecessors.
How to differentiate between types of LK2
There are several methods of determining the specification of an LK2: Looking at the serial number of a unit and using the LK2 Product History (accessible via Linfo website Product Information) will tell you which revision it was sold as. Since, however upgrade kits were sold by Linn in large quantities to allow customers to convert their early version LK2 into the latest spec, many units are not what they seem. The following information will help you to determine the specification of a unit if its exact history is unknown. LK280s had LK280 printed on the facia earlier units (LK2 & LK275) had LK2 printed there, but beware an earlier version may have been upgraded to LK280 spec. LK260s and LK275s had a red power LED and LK280s had a green LED. This is handy as a quick and easy indicator but is not 100% reliable (LEDs are easily changed) The best way to determine a units spec is simply to remove the sleeve and look at the boards that are fitted (see below). Distinguishing Features of Different Board Types PCAS 003 used in LK260/LK275

some faults, simple checks are detailed that you can use to rule out the problem without replacing any parts, whereas for other faults, the simplest way to rule out the problem is to replace the component(s) listed Cure Quite simply the action that you must take to cure the problem.
Important Safety Information & Installation Advice

Mains connections

This appliance must be earthed both for Safety and functional reasons.

Lethal Voltages

Inside the LK2, lethal voltages are present, avoid powering up an LK2 with the sleeve removed or with any live parts exposed. If you must work under such circumstances, DO NOT touch any part of the circuitry or any electrical connections and take great care to avoid electrocution.

Placement

Location & Environment Do not locate near electronic products that may transmit RF, such as computers, fax machines, TVs etc, or connect them to the same mains socket as these devices. Also avoid close contact with the mains or signal leads of such products careful routing of the cable may be required. Although the LK2 can usually be stacked along with other products with no problem, it is better if possible to keep it apart from other products to prevent its operation being adversely affected by the heat and strong electrical field emitted by some products; also - since the LK2 can emit a considerable amount of heat and has a fairly strong electrical field, it is better to keep it away from other devices that may be adversely affected by this. Avoid locations that have high humidity or the chance of the unit getting wet. Avoid locations where there is a lot of dust. Handling & general maintenance. Always handle the LK2 with great care IT IS VERY HEAVY. Always turn off the LK2 and wait at least 30 seconds before connecting or disconnecting any plugs to/from the sockets at the back of the unit to avoid damage to the speakers. If you are carrying out any work on the LK2 with its sleeve removed, ALWAYS take anti-static precautions as tiny static discharges from your body, which you may be completely unaware of, can damage electronic circuitry and cause major problems. Anti-static earth mats & wrist straps must be used when handling any of the circuit boards or any spare parts.

Page4 Contents

Procedure for Dismantling and Re-assembling the LK2
Step 1. Remove the boards from the LK2 Remember to keep all the screws and other parts that you remove from the LK2 in a safe place to re-use later. 1. Disconnect LK2 from everything and especially the mains (or Spark). 2. Place a soft cloth on the workbench & lie the LK2 upside down on the cloth. Using a No2 posidriv screwdriver, remove the 4 screws that hold the sleeve on to the LK2. Stand the LK2 on its facia and slide the sleeve up and off. Carefully set it aside in a safe place where it will not get scratched or damaged. 3. Remove the 4 allen bolts or screws (older units used screws) holding the speaker sockets on to the back panel. Do this to both channels. 4. Disconnect both transformer connectors (the cables going from transformer to board) from the board 5. Lift the LK2 up so that it is standing on one of the heatsinks. Each channel is held into the tray by 2 countersunk screws that attach to the heatsink on the underside. Hold the channel that is now uppermost (to prevent it from falling once it has been freed) and remove the two screws from this channel only. Lie the LK2 down (correct way up) and remove the channel that you have just loosened this can sometimes be tricky so follow these instructions: Pull the board slightly toward the front of the unit until the 3-pin cannon input socket at the rear is clear of the back panel it may sometimes be necessary to push the back panel slightly in the opposite direction until the socket is completely clear. Lift the end of the board containing the 3-pin cannon socket upwards (see picture) until that end of the board is clear of the tray. Some delicate manoeuvring may be necessary, but dont force it.

Once heatsink and board are matched up, tighten bolts.
If heatsink was attached with allen screws: Page7 Contents

2. 3. 4.

Slide the single nut/bolt (still attached to board) into the middle of its slot do not tighten Rest the board on the heatsink in a central position. Line up the screw holes in the board with those in the heatsink and screw in all four screws but do not tighten fully. Line up the board and heatsink so that they are parallel and level with each other (as diagrams above) and then tighten the screws fully. Tighten the nut/bolt Refit boards into tray just do the reverse of the dismantling process described at the start of this document. Refit sleeve Test amp fully

Page8 Contents

Fault Finding on the LK2 hints & tips
The LK2 circuitry is notoriously difficult to fault-find on in the traditional way (tracing signals, measuring voltages etc), so this manual seeks to help you to avoid this ordeal. Check the fault tables below firstly, to see if your fault is included and if not, use the information in this section. Trip One issue that may prevent you from fault-finding is the inclusion of the Trip or protection circuitry which will shut down the entire board if it detects a problem that might cause damage to the amp or the speakers. If trip occurs, it makes fault finding very very difficult as no power reaches the amplifier section of the board. If this happens it is best to try to find the fault with the power off use the information found in the Fault Tables below and in this section. Isolating Faulty Components in the LK2 Circuit Common Faults Around 60-70% of faults in an LK260 or LK275 board only (i.e. not LK280) are attributable to just 4 components. See LK2 Reliability Modifications (accessible via Linfo Product Information) for instructions on how to replace these components and prevent re-occurrence. This modification is a good first step for a faulty PCAS 003 board and should even be carried out to working boards as a preventative measure. Transistors The majority of remaining faults on an LK2 board are caused by faulty transistors, so this is a good place to start. If the transistors develop a fault, they normally develop a short circuit (zero ohms) or low impedance across one or more junctions, so it is usually quite a simple job to trace the faulty transistor by measuring across every junction of every transistor while the transistor is still in circuit. This might seem daunting, given the number of transistors on each board, but it is definitely a worthwhile exercise as it may save you many hours of conventional faultfinding and does not take as long as you might think (about 20 minutes per board). Just measure the impedance across all 3 junctions (Emitter Bass; Emitter Collector; Bass Collector) of every transistor on the faulty board. In general a working junction will measure many Kohms or even Megohms, whereas a faulty junction will tend to measure almost short circuit perhaps a few ohms possibly up to 500ohms at most. If in doubt, compare with the same junction on the good channel and replace transistor if you suspect faulty. It is advised that you check every single transistor on the board, i.e. dont stop if you find a faulty one, as quite often there is more than one faulty transistor on the board. Remember to include the big transistors (the 4 that are clamped to the heatsink) when measuring. The above test, while not absolutely guaranteed to find every faulty transistor, will find the vast majority. Remember that it is quite common for more than one component to be faulty, as often a faulty component will cause damage to others around it in the circuit. See below for advice on how to check for this. Other components Other components are slightly less straightforward. The same principles as with Transistors above can be applied (measure using an ohmmeter) but there is a lot more work involved and a lesser chance of success as these parts are less likely to go faulty and less likely to follow such a straightforward pattern as the transistors. If you have a fault that is not caused by any of the faults listed in this manual i.e. the fault tables and this section - then try to narrow the fault down to an area of the circuitry using conventional fault-finding and then measure and/or replace the components in that area. Resistors can of course be easily measured for impedance but are very unlikely to go faulty unless another component failure has damaged them, so look for telltale signs like scorching etc on or around the resistor that might indicate this. The Capacitors on this circuit can also be checked using an ohmmeter as above. Sometimes capacitors will internally short-circuit so worth a quick measurement. Check the components (as transistors above) using an ohmmeter.

Fuse blowing Doesnt power up or Powers up (display LED lit) but no function. Possible distortion or poor sound quality
Mains surges Wrong mains voltage for LK2 type mains voltage is too high (e.g. 115V unit being used with 240V mains supply.)
May be intermittent but usually constant

Constant

Transformer faulty. To check if it is definitely the transformer, power down the unit, replace fuse, disconnect the transformer output from the Main board and power up. If the transformer IS the cause, the fuse will continue to blow. If the fuse remains intact, the fault is more likely to be on the board. Bridge rectifier diode on amplifier board faulty (probably internally short circuit). These are the four large diodes which can be found on the underside of each amplifier board, under the big capacitors Try measuring across all four with an ohmmeter if one has an internal short circuit, it should be quite obvious.

Page11 Contents

Big capacitor(s) faulty probably internally short circuit. Measure across both capacitors on the channel that is causing the fuse to blow a faulty capacitor will measure short circuit or certainly low impedance. If in doubt, compare with good channel. See Introduction to Fault Finding section (accessible via Linfo Website - Product Information) for tips on how to isolate faulty board Fault inside LK2, e.g. short circuit or similar.
Replace faulty capacitor Part details: 10000uF; +/- 20%; 64V; Electrolytic Capacitor (Linn part no: CAP 085) Same part can be used for any version of LK2
See Introduction to Fault Finding section (accessible via Linfo Website - Product Information) for tips on tracing the fault. Also see circuit diagrams.

Page12 Contents

Amplifier problems Fault Table

No output

Symptom No output from both channels No output from one channel Circumstances Possibly intermittent Applies only to LK260 & LK275 Probably constant May be intermittent Possible Cause(s) Unit not powering up correctly. One of the Reliability Modification components has failed Amp has tripped. Cure See Power up problems section above Carry out LK2 Reliability Modifications procedure can be accessed via Linfo Product Information. See Trip Faults section below.
No output from one channel OR occasionally may affect both channels No output from one channel
Applies only to LK280 Probably constant
No output from one channel
Applies only to LK275 & later versions of LK260. Probably constant

Tripping

Regulator U1 or U2 faulty

Page15 Contents

Power transistor (the large transistors clamped to the heatsink) faulty. It is sometimes possible to measure these transistors using an ohmmeter to check if faulty (usually internal short-circuit across one or more of the junctions), but also there is the possibility that the transistor measures okay but is indeed faulty. It will sometimes be necessary to change them to confirm or rule out this fault. Power transistor (the large transistors clamped to the heatsink) faulty. It is sometimes possible to measure these transistors using an ohmmeter to check if faulty (usually internal short-circuit across one or more of the junctions), but also there is the possibility that the transistor measures okay but is indeed faulty. It will sometimes be necessary to change them to confirm or rule out this fault. Power transistor (the large transistors clamped to the heatsink) faulty. It is sometimes possible to measure these transistors using an ohmmeter to check if faulty (usually internal short-circuit across one or more of the junctions), but also there is the possibility that the transistor measures okay but is indeed faulty. It will sometimes be necessary to change them to confirm or rule out this fault. Faulty component in circuit.
Check / replace power transistor(s). Parts may be as listed in the box above or they may be as listed below, depending on whether it is an earlier or later version of LK260. Part details Q20 & Q27 TIP36C; PNP; 100V; 25A; TO218 (Linn part no: TRAN 005) Q24 & Q31 TIP35C; NPN; 160V; 15A; TO218 (Linn part no: TRAN 004) See Fault Finding on the LK2 hints & tips section at the beginning of this manual.
Distortion / crackling etc
Symptom Output distorted may one or both channels Circumstances May be intermittent Possible Cause(s) Power-up problem if amp receives insufficient power it will struggle to amplify the signal and distortion will occur Cure See Power-up problems section above.

Page16 Contents

Output very badly distorted
Applies only to LK260 & LK275 Probably constant May be intermittent
One of the Reliability Modification components has failed Faulty component in circuit.

Distorted output

Crackling noise from output
Probably intermittent may be temperature dependent
Transistor in circuit faulty junction is breaking down
Carry out LK2 Reliability Modifications procedure can be accessed via Linfo Product Information. See Fault Finding on the LK2 hints & tips section at the beginning of this manual. See Introduction to Fault Finding (accessible via Linfo Product Information) Or See Fault Finding on the LK2 hints & tips section at the beginning of this manual.

DC at output

Symptom DC voltage at output. Fault symptoms vary levels of voltage etc. DC at output Circumstances Probably constant Possible Cause(s) Regulator U1 or U2 faulty Cure Replace faulty regulator part details: U1 LM317T Voltage regulator (Linn part no: IC 005) U2 LM337T Voltage regulator (Linn part no: IC 006) See Fault Finding on the LK2 hints & tips section at the beginning of this manual.

Page17 Contents

LK2(60) & LK275 Reliability Modifications
Some components on the PCAS 003 (used in the LK260 & LK275) are sometimes prone to failure after many years of use. This modification can be carried out as a preventative measure to prolong the life of the amplifier or as a combined repair / prevention if one of the components has failed. Carrying out this modification will repair around 60 70% of LK2 faults
Important Information about this modification
Please read through this procedure in its entirety before starting any work. It is important to follow ALL instructions carefully and exactly This procedure involves soldering and de-soldering and it is advised that only personnel with a fairly high degree of soldering skill undertake this task. Due to the age and the years of heat stress some of the solder joints may have changed their chemical properties and if this is the case it will be quite difficult to melt them. Use flux (or melt new solder onto the old solder joint), Use heat and patience - not force. The changes outlined in this procedure will protect the LK2 from similar potential failures in the future by using higher wattage resistors than were originally used and adjusting the position of some components to minimise heat damage It is advised that all these modifications are carried out to both channels.
Estimated time for completion of this task:

1 hour

CAUTION Important Safety Information
Residual Voltage. With certain faults especially but also under normal circumstances, there can be residual voltage stored in the boards which could cause quite a serious electric shock. To avoid this, it is best to leave the LK2 switched off for a few hours before starting work on it and then using a voltmeter, measure across the metal contacts of each of the big capacitors (DO NOT TOUCH) on each channel (DC voltage). If there is a voltage remaining on these capacitors then it is important to discharge it either short across the + & - contacts with a screwdriver this can cause a harmless but spectacular and terrifying bang combined with a huge spark. It is much more pleasant to connect one of the resistors that you will use for the mod the 2.4Kohm/2.5Watt and connect this across the contacts of the capacitors until the voltage has discharged. The LK2 is very heavy and has sharp fins on the heatsink be very careful when lifting, handling, dismantling and re-assembling not to injure yourself.

Paul ONeill Copyright 2000 Linn Products Limited. All rights reserved.
LK2 Reliability Modifications

Fault Symptoms

There are several different symptoms, depending on what component has failed (symptoms usually affect one channel only): No output at all Bad distortion at output DC at output

Units affected

Potentially all LK260s or LK275s (those not upgraded to LK280)

Equipment Required

(Those items marked
may not definitely be required)
Workbench clear of debris and clutter No2 Posidriv (Supadriv) Screwdriver ~ No1 Posidriv (Supadriv) Screwdriver ~ 2.5mm Hex key or Allen Key ~ Medium sized flat-blade screwdriver 7mm spanner or nut-runner 5.5mm spanner or nut-runner Soldering Iron, temperature controlled 25 watt with fine tip Solder Sucker Fine solder Paper handkerchiefs or paper towels Heatsink compound (a white grease-like substance that improves heat conduction) Fine Pliers Soft cloth

Parts Required

20Kohm, 2.5Watt resistor 2.4Kohm, 2.5Watt resistor 220pF 160V Polystyrene capacitor 68pF 160V Polystyrene capacitor Qty Qty Qty Qty 2 (per unit) 2 (per unit) 2 (per unit) 2 (per unit)
Note if you cannot find the above parts available in your local area, some alternatives are available in the case of the resistor wattage values: It is possible to use a higher wattage resistor in each case, although it tends to be the case that the higher the wattage, the larger the resistor and it may not be able to physically fit in the space available or may touch against another device or component, especially in the case of R33 (not a good idea). It is possible to use a slightly lower wattage resistor in each case, however if too low. this will shorten the life of the resistor and the fault may re-occur. A minimum of 1 watt is recommended.

Paul ONeill

Copyright 2000 Linn Products Limited. All rights reserved.

Procedure

Step 1. Remove the boards from the LK2 Remember to keep all the screws and other parts that you remove from the LK2 in a safe place. 1. 2. Disconnect LK2 from everything and especially the mains (or Spark). Place a soft cloth on the workbench & lie the LK2 upside down on the cloth. Using a No2 posidriv screwdriver, remove the 4 screws that hold the sleeve on to the LK2. Stand the LK2 on its facia and slide the sleeve up and off and carefully set it aside in a safe place where it will not get scratched or damaged. Remove the 4 allen bolts or screws (older units used screws) holding the speaker sockets on to the back panel. Do this to both channels. Disconnect both transformer connectors (the cables going from transformer to board) from the board Lift the LK2 up so that it is standing on one of the heatsinks. Each channel is held into the tray by 2 countersunk screws that attach to the heatsink on the underside. Hold the channel that is now uppermost (to prevent it from falling once it has been freed) and remove the two screws from this channel only. Lie the LK2 down (correct way up) and remove the channel that you have just loosened this can sometimes be tricky so follow these instructions: Pull the board slightly toward the front of the unit until the 3-pin cannon input socket at the rear is clear of the back panel it may sometimes be necessary to push the back panel slightly in the opposite direction until the socket is completely clear. Lift the end of the board containing the 3-pin cannon socket upwards (see picture) until that end of the board is clear of the tray. Some delicate manoeuvring may be necessary, but dont force it.

3. 4. 5.

Step 2. Remove the heatsinks from the boards 1. Using the 5.5mm spanner or nut-runner, loosen the single nut/bolt found beside the 3-pin cannon socket (see picture below) do not remove the nut completely, but loosen it to the point where only a very small amount of the bolt is protruding from one side of the nut. The board is now held on to the heatsink by 4 allen screws or 4 nuts/bolts (see picture below). If nuts/bolts are fitted, loosen them but do not remove them (as with single bolt above), pull the board upwards until there is a gap between the board and the heatsink and then slide the board to one side. If the board will not move easily, check that you have loosened all 5 nuts/bolts. If all are loosened correctly and it is still not free, the board may be held on by the heatsink compound and will require some slight pressure to free it. If the board is held on by allen screws, completely remove all 4 screws, lift the board away from the heatsink and slide the single bolt beside the cannon socket sideways to free the board.
Step 3. Carry out the modification 1. Locate the components as listed in the table below and replace with the values shown (see pictures below for location of these components). Do this for both channels. Please note R49 depending on what size of part you have purchased, it may be too big for the space available. If so, the part can be inserted to stand up as shown below. R49 resistor leg bent into this shape R49 resistor body standing at 90 degrees to board

Circuit board

Please note R33 is located underneath one of the big capacitors C16 (see picture below). The capacitor holder must be removed from the board to access the resistor. Turn the board upside down and you will see that the capacitor holder is held by two nuts/bolts. Remove the two nuts and the capacitor will come away from the board but be careful, as it will still be held by a pair of wires. If the nuts/bolts keep spinning instead of coming loose, insert a medium sized flat-blade screwdriver under the capacitor and press it against the head of the bolt while turning the nut this usually provides enough grip to hold the bolt so that the nut comes free. Component R33 R49 C6 C19 Replace with: 20Kohm, 2.5Watt resistor 2.4Kohm, 2.5Watt resistor 68pF 160V Polystyrene capacitor 220pF 160V Polystyrene capacitor
R33 is found underneath this capacitor C6 Q10
In order to prevent the two polystyrene capacitors that you have just replaced from failing at a later date, make the following small adjustments to the position of some components: Bend Q10 away from C6 (towards the middle of the board). As shown in picture above Bend C6 away from Q10 (towards the 3-pin cannon socket). As shown in picture above Bend C19 away from Q10 towards R49 but do not bend it too close to R49 position it so that it is about half way between Q10 and R49. As shown in picture above These steps are advised because Q10 and R49 get quite hot and can sometimes melt the polystyrene capacitors (over a period of many years). Positioning the components as above minimises the effect of this heat and prolongs the life of the capacitors.

C.Des (Component Designator)
Every component on every Linn circuit board has an individual identification code known as a Component Designator (C001, Q012, R345 etc). The designator shown in the table matches that printed on the circuit board beside each component. These designators are coded according to type of component at the start of each designator there is a letter and this describes the component type. The main types are shown below: C - Capacitor P - Connector Q - Transistor R - Resistor U - IC The components are listed in alphabetical order by Component Designator

Part Number

Our internal part number for the component. Quote this part number if ordering the part from Linn. We advise however that you try to source parts locally as most components are commonly available from any good electronic parts supplier much faster and cheaper than we can supply and also, not every part listed here can be ordered from Linn. If you have problems finding the part locally, we will do our best to help you, but we cannot guarantee availability of any part listed.

Description

All the technical details that you will require to order the part from your local or national electronic spares supplier. Includes (if applicable) the name(s) of our preferred manufacturer(s) for each part.

P R I N T

B I L L

M A T E R I A L S

15-AUG-00 Page 1
Assembly Number: PCAS 003
POWER AMPLIFIER PCB ASSEMBLY *OBSOLETE PART* Units: ONES BOM Type: C

Quantity -------1.00000

Units ----ONES

T C.Des - ----R C001

Part Number ----------CAP 035
Description Type Kit Cost -------------- --- ---4N7F,+2%,-2%,63V,PST,TH,CO400,,,,, C N Y ,,,,,, 100UF,+20%,-20%,10V,TANT,TH, PCO200,,,,,,,STC TAG,,THOMSON,, C N N Y Y
** Warning - Part OBSOLETE on 09-JAN-1995 1.00000 ONES R C002 CAP 034 1.00000 ONES R C003 CAP 003
22UF,+50%,-20%,50V,ELTR,TH,PCO100, C ,,,,,,NCC,,RUBYCON,,MULLARD 22UF,+50%,-20%,50V,ELTR,TH,PCO100, C ,,,,,,NCC,,RUBYCON,,MULLARD 1NF,+10%,-10%,63V,CERA,SM,CC0805,, C ,,,,,,,,, 68PF,+2%,-2%,160V,PST,TH,CO100,,,, C ,,,,,,, 33UF,+20%,-20%,10V,TANT,TH,PCO200, C ,,,,,,STC TAG,,THOMSON 33UF,+10%,-10%,63V,PEST,TH,PCO200, C ,,,,,,STC TAG,,THOMSON 100NF,+10%,-10%,63V,PEST,TH,CO200, C ,,,,,,,,,, 100UF,+20%,-20%,63V,ELTR,TH, PCO200,,,,,,,ECC,,RUBYCON,, 100UF,+20%,-20%,63V,ELTR,TH, PCO200,,,,,,,ECC,,RUBYCON,, C C

1.00000 1.00000

ONES ONES

R C004 R C005

CAP 003 CAP 099

N N N N

Y Y Y Y
** Warning - Part OBSOLETE on 27-APR-1989 1.00000 ONES R C006 CAP 039 1.00000 ONES R C007 NO INFO NO LINN PART NUMBER EXISTS FOR THIS PART 1.00000 ONES R C008 NO INFO NO LINN PART NUMBER EXISTS FOR THIS PART 1.00000 1.00000 ONES ONES R C009 R C010 CAP 068 CAP 020

R D011 R D012 R D013

MISS 010 MISS 010 MISS 010

15-AUG-00 Page 3

POWER AMPLIFIER PCB ASSEMBLY *OBSOLETE PART* Units: ONES BOM Type: C Type Kit Cost ---- --- ---C N Y C N Y
T C.Des - ----R D014 R D015
Part Number ----------MISS 001 MISS 001
Description ----------TYPE FUNCTION 1N4148 DIODE TYPE 1N4148 FUNCTION DIODE

R D016

MISS 014
POWER AMP MAINS INDICATOR LED. ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, BD140,PNP,80V,1.5A,TO126,140, MOTOR, BD140,PNP,80V,1.5A,TO126,140, MOTOR, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, BD139,NPN,80V,1.5A,TO126,139, MOTOR,
** Warning - Part OBSOLETE on 07-SEP-1992 1.00000 ONES R Q001 TRAN 001 1.00000 1.00000 ONES ONES R Q002 R Q003 TRAN 001 TRAN 002
R Q004 R Q005 R Q006 R Q007
TRAN 002 TRAN 001 TRAN 001 TRAN 002

R Q008 R Q009 R Q010

TRAN 002 TRAN 002 TRAN 007
** Warning - Part OBSOLETE on 30-OCT-1996 1.00000 ONES R Q011 TRAN 007 ** Warning - Part OBSOLETE on 30-OCT-1996 1.00000 ONES R Q012 TRAN 001 1.00000 1.00000 ONES ONES R Q013 R Q014 TRAN 001 TRAN 006
** Warning - Part OBSOLETE on 30-OCT-1996

15-AUG-00 Page 4

T C.Des - ----R Q015 R Q016
Part Number ----------TRAN 002 TRAN 001
Description ----------ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, 2SA1386,PNP,160V,15A,MT100,1386, SANKEN, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, 2SC3519,NPN,160V,15A,MT100,3519, SANKEN, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, 2SA1386,PNP,160V,15A,MT100,1386, SANKEN, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, ZTX753,PNP,100V,2A,ELINE,753, ZETEX, TYPE MPS A93 POLARITY PNP OBSOLETE
R Q017 R Q018 R Q019 R Q020
TRAN 001 TRAN 002 TRAN 001 TRAN 017
R Q021 R Q022 R Q023 R Q024
TRAN 002 TRAN 002 TRAN 002 TRAN 018
R Q025 R Q026 R Q027 R Q028
TRAN 001 TRAN 001 TRAN 017 TRAN 002

R Q029 R Q030

TRAN 002 TRAN 010
** Warning - Part OBSOLETE on 13-MAR-1990 1.00000 ONES R Q031 TRAN 018
2SC3519,NPN,160V,15A,MT100,3519, SANKEN,

15-AUG-00 Page 5

T C.Des - ----R Q032 R Q033
Part Number ----------TRAN 001 TRAN 001
Description ----------ZTX653,NPN,100V,2A,ELINE,653, ZETEX, ZTX653,NPN,100V,2A,ELINE,653, ZETEX, TYPE MPS A43 POLARITY NPN OBSOLETE

R Q034

TRAN 009
** Warning - Part OBSOLETE on 13-MAR-1990 1.00000 ONES R R001 RES 029 1.00000 1.00000 ONES ONES R R002 R R003 RES 017 RES 021
1K,1%,MF,1/4W,0.25W,200V,50ppm,,,
4K7,1%,MF,1/4W,0.25W,200V,50ppm,,, C 100R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 4K3,1%,MF,1/4W,0.25W,200V,50ppm,,, C 4K7,1%,MF,1/4W,0.25W,200V,50ppm,,, C 120R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 120R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 120R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 220R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 220R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 4K3,1%,MF,1/4W,0.25W,200V,50ppm,,, C
R R004 R R005 R R006 R R007
RES 078 RES 017 RES 030 RES 030
R R008 R R009 R R010 R R011
RES 030 RES 001 RES 001 RES 078

R R012 R R013 R R014

RES 022 RES 022 RES 023
820R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 820R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 910R,1%,MF,1/4W,0.25W,200V,50ppm,, C ,

15-AUG-00 Page 6

T C.Des - ----R R015 R R016
Part Number ----------RES 041 RES 023
Description Type Kit Cost -------------- --- ---5K6,1%,MF,1/4W,0.25W,200V,50ppm,,, C N Y 910R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 5K6,1%,MF,1/4W,0.25W,200V,50ppm,,, C 620R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 620R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 180R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 1K1,1%,MF,1/4W,0.25W,200V,50ppm,,, C 1K1,1%,MF,1/4W,0.25W,200V,50ppm,,, C 180R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 4R7,1%,MF,1/4W,0.25W,200V,50ppm,,, C N Y
R R017 R R018 R R019 R R020
RES 041 RES 042 RES 042 RES 043
R R021 R R022 R R023 R R024
RES 035 RES 035 RES 043 RES 082
R R025 R R026 R R027 R R028
RES 133 RES 133 RES 048 RES 025
4R7,5%,WWC,XX,4W,999V,999ppm,,, 4R7,5%,WWC,XX,4W,999V,999ppm,,,
12R,1%,MF,1/4W,0.25W,200V,50ppm,,, C 22K,1%,MF,1/4W,0.25W,200V,50ppm,,, C

R R029 R R030 R R031

RES 047 RES 009 RES 002
0R47,10%,WWE,W21,2.5W,100V,75ppm,, C , 27R,1%,MF,1/4W,0.25W,200V,50ppm,,, C 150R,1%,MF,1/4W,0.25W,200V,50ppm,, C ,

15-AUG-00 Page 7

T C.Des - ----R R032
Part Number ----------RES 017
Description Type Kit Cost -------------- --- ---4K7,1%,MF,1/4W,0.25W,200V,50ppm,,, C N Y

1.00000 ONES R R033 NO INFO 20K,1%,MF,2.5W, 200V,50ppm,,, C N Y NOTE-ORIGINAL PART FOR R033 WAS RES 045 HAD INSUFFICIENT POWER RATING USE MINIMUM 1WATT PART 1.00000 1.00000 1.00000 1.00000 ONES ONES ONES ONES R R034 R R035 R R036 R R037 RES 033 RES 013 RES 050 RES 038 6K2,1%,MF,1/4W,0.25W,200V,50ppm,,, C 180K,1%,MF,1/4W,0.25W,200V,50ppm,, C , 0R1,10%,WWE,W21,2.5W,100V,75ppm,,, C 2K2,1%,MF,1/4W,0.25W,200V,50ppm,,, C N N N N Y Y Y Y
R R039 R R040 R R041 R R042
RES 058 RES 017 RES 002 RES 009
33K,1%,MF,1/4W,0.25W,200V,50ppm,,, C 4K7,1%,MF,1/4W,0.25W,200V,50ppm,,, C 150R,1%,MF,1/4W,0.25W,200V,50ppm,, C , 27R,1%,MF,1/4W,0.25W,200V,50ppm,,, C
R R043 R R044 R R045 R R046
RES 033 RES 013 RES 038 RES 050
6K2,1%,MF,1/4W,0.25W,200V,50ppm,,, C 180K,1%,MF,1/4W,0.25W,200V,50ppm,, C , 2K2,1%,MF,1/4W,0.25W,200V,50ppm,,, C 0R1,10%,WWE,W21,2.5W,100V,75ppm,,, C

R R048

RES 058
33K,1%,MF,1/4W,0.25W,200V,50ppm,,, C
1.00000 ONES R R049 NO INFO 2.4K,10%,WWE,W21,2.5W,100V,75ppm,, C N NOTE ORIGINAL PART WAS 0.25W HAD INSUFFICIENT POWER RATING. USE MINIMUM 2.5W PART 1.00000 1.00000 ONES ONES R R050 R R051 RES 078 RES 063 4K3,1%,MF,1/4W,0.25W,200V,50ppm,,, C 18R,1%,MF,1/4W,0.25W,200V,50ppm,,, C N N

15-AUG-00 Page 8

T C.Des - ----R R052 R R053
Part Number ----------RES 048 RES 009
Description Type Kit Cost -------------- --- ---12R,1%,MF,1/4W,0.25W,200V,50ppm,,, C N Y 27R,1%,MF,1/4W,0.25W,200V,50ppm,,, C N Y
R R055 R R056 R R057 R R059
RES 009 RES 048 RES 009 RES 018
27R,1%,MF,1/4W,0.25W,200V,50ppm,,, C 12R,1%,MF,1/4W,0.25W,200V,50ppm,,, C 27R,1%,MF,1/4W,0.25W,200V,50ppm,,, C 15K,1%,MF,1/4W,0.25W,200V,50ppm,,, C

R U001 R U002

IC 005 IC 006
LM317T,VOLTAGE REGULATOR,TO220, 317T,NATSEM, LM337T,VOLTAGE REGULATOR,TO220, 337T,NATSEM,THOM