Warnings, Cautions and others
THE FOLLOWING APPLIES ONLY FOR U.S.A.

Caution:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION:TO REDUCE THE RISK OF ELE CTRIC SHOCK, DO NOT REMOVE SCREWS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SE RVICE PERSONNEL.
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION!

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. IMPORTANT FOR LASER PRODUCTS 1) 2) CLASS 1 LASER PRODUCT DANGE R: Visible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. 3) CAUTI O N: Do not open the top cover. There are no user serviceable parts inside the Unit; leave all servicing to qualified service personnel.

WARNING:

TO RE DUCE THE RISK OF FIRE, ELE CTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE, DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

Caution!

CD-R/RW discs recorded using a personal computer or a CD recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player s lens. Unfinalized CD-R/RW discs can be played, but not all time information (playing time, etc.) will be displayed. DVD-RW discs written in the VR format DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM, PHOTO CD, Check the copyright laws in your country before recording from DVD VIDEO, SVCD, Video CD, Audio CD, MP3 and JPEG discs. Recording of copyrighted material may infringe copyright laws

C auti on POWER button Disconnect the mains plug to shut the power off completely. The POWER button in any position does not disconnect the mains line. The power can be remote controlled.

Disc Information

n Playable Disc types

Disc Types DVD-VIDEO

Characteristics
This unit can playback DVD VIDEO discs and the region code is printed on the rear of the unit. Example :
DVD-R/RW DVD+R/RW Video CD (VCD) Super Video CD

(SVCD)

DVD-R, DVD-RW and DVD+R, +RW, discs written in the DVD-VIDEO format and finalized. Video with CD sound, VHS quality & MPEG-1 compression technology.
Audio CD CD-R/RW (JPEG/MP3)
CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time. This unit can play CD-R and CD-RW discs recorded with CD Audio or Video CD format, or with JPEG/MP3 files. Close the sessions or finalize the disc after recording.

n Recordable Disc types

Disc Types DVD+R/RW
DVD+R discs written in the DVD+R Video format. DVD+RW discs written in the DVD+RW Video format.
N otes : The DVD Logo is a trademark. Use discs with the above logos and that conform to specif ications. The unit cannot play other discs correctly. Do not use irregularly shaped discs (e.g. heart-shaped), as these can damage the unit. It may not be possible to play CD-R, CD-RW, DVD-R and in all cases due to the type of disc or condition of the recording.
n Video System (NTSC & PAL) NTSC is used. This unit converts PAL system DVD-Audio to NTSC for play. The picture is compressed to show it in its entirety, but this may cause it to be stretched vertically. n Aspect Ratio 4:3 (Letter Box) Standard

Unplayable Disc types

The unit does not playback discs listed below. If you try to play back these discs, noise may generate causing damage to speakers. 1) Unfinalized discs 2) DVD-RW discs written in the VR format 3) DVD-ROM, DVD AUDIO, CD-ROM, PHOTO CD, SACD n Region Code of DVD Video This unit can playback DVD VIDEO discs and the region code is printed on the rear of the unit. Examples of playable DVD-VIDEO discs: 4:3 Pan&Scan 16:9 (Wide-Screen) n Others Audio: Appears at the beginning of a scene recorded with multiple audio languages. Subtitle : Appears at the beginning of a scene recorded with multiple subtitle languages. Notes: The unit region code is printed on the rear of the unit. s n Audio System Dolby Digital Linear PCM Angle : Appears at the beginning of a scene recorded from multiple angles. n Playable File Types JPEG, MP3 n To Clean Discs Wipe DVD-Vide o , VCD, SVCD, CD discs with a damp cloth and then wipe dry. Do not touch the surface of the disc.

5) LIN E OU T (V ID E O/A U D IO L/R ) Jac ks Connects the input of external equipment. 6) LIN E OU T (S -V ID E O) Jac k Connects the input of external equipment. 7) D IG ITA L OU T (C OA XIA L) Jac k Connects an amplifier or receiver having a digital input jack. 8) D IG ITA L OU T (OPTIC A L) Jac k Connects an amplifier or receiver having a digital input jack. 9) A C IN termi nal Connects the power cord.
Rear panel connections (For 5001B)
1) V HF/UHF IN /OU T Jac ks Connects antenna cables. 2) S C A R T IN Jac k Connects the input of external equipment. 3) S C A R T OU T Jac k Connects the output of external equipment. 4) LIN E OU T (S -V ID E O) Jac k Connects the input of external equipment. 7 5) LIN E OU T (V ID E O/A U D IO L/R ) Jac ks Connects the input of external equipment. 6) D IG ITA L OU T (C OA XIA L) Jac k Connects an amplifier or receiver having a digital input jack. 7) D IG ITA L OU T (OPTIC A L) Jac k Connects an amplifier or receiver having a digital input jack. 8) A C IN termi nal Connects the power cord.
Before making connections
1) Do not connect the AC power cord until all other connections have been made. 2) Connect VIDEO OUT of the unit directly to the video input of your TV. Connecting VIDEO OUT of the unit to a TV via a VCR may cause a monitor problem when playing back a copy-protected disc. You may also have a monitor problem when connecting the unit to an integrated TV/Video system.
Connecting the Antenna cable and Television
Before using the unit, follows the steps connects the unit to the antenna cable and TV.

For 5001A/5001D Only

Connecting to a TV w ith a COMPOSITE jacks You can use the COMPOSITE OUT jacks to connect the unit to TV.

For 5001B Only

Connecting to a TV w ith SCART jack You can use the SCART OUT jack to connect the unit to your TV (F Europe Only). or
N otes Connect the unit directly to your television. Do not place the unit on top of am plifiers or equipm ents that m ay becom e hot. The heat can dam age the unit. 8
For Better Picture (For 5001A/5001D Only)
There are two types of connection, S-Video, Component.

1. S-Video Out

Connecting to a TV with an S-Video jack You can use the S-Video output instead of the standard video out jack to connect this player to TV.
Notes When using the S-Video output jack, do not connect other VIDEO OUT jacks on the unit. Please set the correct video output from the unit by pressing "SETUP" button on the remote control to setup "System --> Output --> S-Video".

Aspect Ratio

Select 4:3 (regular) or 16:9 (widescreen) to suit your television. If you have a regular 4:3 television, you can also select how video on some discs is shown 4:3 Letter Box (Factory preset) (select when you connect the unit to a normal (4:3) TV.) When playing back a DVD VIDEO disc recorded in wide picture format, the picture is shown with black bars at the top and bottom. 4:3 Pan & Scan (select when you connect the unit to a normal (4:3) TV.) When playing back a DVD-VIDEO disc recorded in wide picture format, the picture is zoomed to fill the screen vertically, and the left and right sides of the image are chopped off. Note, however, that the picture will be shown in the 4:3 LB mode even if you select the 4:3 PS mode depending on the disc. 16:9 Wide Screen (select when you connect the unit to a wide-screen (16:9) TV.) N otes : You cannot change the setting during playback. 11
N otes : You must Connect to the component video input terminalsi on a 480P compatible television.
Digital Output P CM / B it str e a m (Enable digital audio output with PCM or encoded data) DTS Out O N / O FF

Before Recording

This recorder can record on DVD+R/DVD+RW disc. Before you record,read the following and select the disc type according to your needs.
4.Press [RECORD] , to start Recording.
After pressing [RECORD] , it may take a short while to start recording.
Recording televison programs
Recording continues until you stop the recording or disc is full.

To stop recording

When you press [ recording to stop. STOP] , it may take a few seconds for

To pause recording

Press [ PAUSE] to pause recording , and if you want to restart recording, press the button again.

1.Press [

POWER] , to turn the unit on.
2.Press [ OPEN/CLOSE] , to open the tray and insert a DVD+R or DVD+RW disc.
Prees the button again to close the tray. If you use an unused DVD+RW, background formatting will be start automatically.
To change the recording mode.
Press [SETUP]. The new setting can't change the current recording but will active in next time. (For more details of recording mode, see page 22) e.q., when you select HQ.

No te s: 1.If the power is failure, the program you are recording may be lost. 2.Before you start, please check that the disc has enough available space for the recording. 3.Y cannot change the channel or recording mode during ou recording. 4.Before to play DVD+R on compatible equipment, please finalize it.
Recording from a VCR or DV/V8 Before to start recording
The unit can accept standard CVBS (RCA) analog audio/video signals or iEEE1394 cable and record them onto DVD in the digital audio or video format of your choice. In this way, the unit functions much like a digital VCR. Examples of use include digitizing videotapes onto DVD+R/DVD+RW, transferring from Video Cassette Recorder or DV/V8 to DVD+R/DVD+RW.
To start recording 1.Press [SETUP] , to select RECORD and to set the recording mode. ( HQ , SP , EP or SLP )
The front panel and rear panel connection
Connect a Video Cassette Recorder or DV/V8 to the unit s input terminals.
2.Put a empty DVD+R or DVD+RW on the tray, with the discs label facing up.
3.Press [SOURCE] , to select the AV- Input ( TV, AV1, AV2, S-Video, DV , Liteon Logo).
N otes : When recording from the S-Video source, the audio input will be sourced from the red (right channel) and white (left channel) audio jacks (labeled R and L, respectively) on the rear panel.
4.Start play on the Video Cassette Recorder or DV/V8. 5.Press [RECORD] , to record your video/audio from the Video Cassette Recorder or DV/V8 onto a DVD+R or DVD+RW.

6.Press [

STOP] , to stop recording.
Press [ PAUSE] to pause recording , and if you want to restart recording, press the button or [RECORD] again.

Timer Recording

Before Timer Recording
9.Press [t] [u] , to select the Source , then press [ENTER] to set the Recording source. TV <-> AV1 <-> AV2 <-> S-V ideo <-> DV 10.Press [t] [u] , to select the Quality , then press [ENTER] to set the Recording quality.
Please check that the disc has enough available space for the timer recording. Before you start to record , follow the steps and set the date , time , picture quality and channel of the program manually.
Setting the timer manually 1.Press [ POWER] , to turn the unit on.
If you use an unused DVD+RW, background formatting will be start automatically.
Mode: HQ <-> SP <-> EP <-> SLP
3.Press [TIMER] , to appear the Timer-record menu.

Multiple languages or soundtracks must be available on the DVD.

A NGLE

To select a different camera angle during DVD playback.
No te s: If continue move left while at the first field, then the search dialogue box will be closed.
No te s: Multiple angles must be available on the DVDDisc.(within the current Title) or Track for playback.

A -B REPEAT

Starting to repeat a desired part. Select Point A at the beginning of the part you want to repeat. Select Point B at the end of the part you want to repeat. The unit locates A and starts repeat playback between A and B. Select [Cancel]. The A-B repeat mode turns off, then normal playback continues.
I NFO RMATI O N To enable or disable the DVD/VCD/SVCD disc information.
To exit t h e Na vigat io n Press [ NAVI.] again or [t] to exit the NAVI mode.
The unit can play a Audio CD or JPEG , MP3 file on a disc.

Audio CD playback

Playing Audio CD

JPEG file playback

Playing JPEG file
1.Put the Audio Disc on the tray.
1.Put the JPEG Disc on the tray.
The disc will be playback automatically.
2.Press [t] or [u] , to skip the picture.
2.Press [ track. 3.Press [ 4.Press [

NEXT] or [

PREVIOUS] , to skip the
PAUSE] , to pause the track playback. STOP] , to stop the track playback.
3.Press [p][q] , to select Rotate RIGHT or Rotate LEFT and Rotate UP Rotate down.
5.Press [0~9] , enter the numberic to select a audio track, and press [ENTER].
Starting play from a selected track.

SlideShow

Concurrent Playing JPE and MP3 file on the sam e disc G
1.Put the Disc on the tray. 4.Press [ playback. 5.Press [ PAUSE] , to pause the picture STOP] , to stop the picture playback.
2.Press [uPLAY ] , to start playback. 3.Press [ NEXT ] or [ the MP3 file. PREVIOUS ] , to skip
Or press [t][u] , to skip the picture. MP3 file playback

Playing MP3 file

4.Press [p][q] , to select Rotate RIGHT or Rotate LEFT and Rotate UP Rotate down. 5.Press [ playback.

Press [

1.Put the MP3 Disc on the tray.
PAUSE] , to pause the slideshow
STOP] , to stop the slideshow playback.
2.Press [ NEXT ] or [ the MP3 file.

PREVIOUS ] , to skip

3.Press [ playback. 4.Press [
PAUSE] , to pause the MP3 file
STOP] , to stop the MP3 file playback.
N otes : The unit may not show the file name correctly If an MP3 file name includes any 2-byte character. The unit cannot support the ID3 tag. The unit cannot support the MP3-Pro and WMA file. The unit supports discs recorded with multiple sessions. The unit only can playback picture or tracks with the following file extensions; JPG or jpg and MP3 or mp3 etc. Time required for reading the disc contents may vary for different discs, depending on the numbers of groups (folders) and tracks (files) recorded, etc. You cannot advance or reverse playback by pressing F. or.F REW. during JPEG , MP3 disc playback. You cannot play select track by pressing the number buttons during MP3 disc playback. The unit supports MP3 file bitrate: 32Kbps ~ 320Kbps s

Editing

Before starting to edit
This section explains the basic edit functions. Please finish all the editing before finalizing the disc.You cannot edit a finializwd disc.
Protecting a title Appear the Title Edit menu 1) Press [p] [q] , to select Protection, then press [ENTER].
PLAY List and Edit menu 1) Press [ PLAY] or [ GUIDER] , to appear the DVD Menu menu.
2) Press [t] [u] , to select the On, then press [ENTER].

The protection is set.

2) Press [EDIT] , to appear the Title Edit menu. Overwrite setting
1) Press [p] [q] , to select Overwrite, then press [ENTER].
Naming a title Appear the Title Edit menu 1) Press [p] [q] , to select Title Name, then press [ENTER].
The display for entering a title name appears.
The Overwrite mode is set.
Erasing a title Appear the Title Edit menu 1) Press [p] [q] , to select Erase, then press [ENTER]. 2) To enter character.
3) When you finish entering the title name,press [t] [u] [p] [q] to select Finish.

The title is erased.

N otes : Both DVD+RW & DVD+R are erasable. But the erased space on DVD+R can't be reused.
Playback 1) Press [ GUIDER ] , to appear the Easy Guider menu. 3) Press [p] [q] , to select the AV- Input ( TV, AV1, AV2, S-Video, DV ) and press [ENTER].
2) Press [p] [q] , to select the Playback , then press [ENTER].

The DVD Menu appears.

If you select TV, press [p] [q] , to select the channel you want to record and press [ENTER].
3) Press [t] [u] , to select a title(program) you want to play and press [ENTER].
5) Press [p] [q] , to select the recording mode and press [ENTER]. ( HQ , SP , EP or SLP )
PAUSE] , to pause playback.
PLAY] to restart normal playback.
Recording Mode HQ SP EP SLP
Recording time minutes minutes minutes minutes

Record

1) Press [ GUIDER ] , to appear the Easy Guider menu.
Press [ENTER] , to confirm recording.

Press [ Press [

STOP] , to stop recording. PAUSE] , to pause recording.
2) Press [p] [q] , to select the Record , then press [ENTER].

Format

N otes : During Playback Record operating , you can select the EXIT to exit the Easy Guider menu.

Finalize For DV D+R only: Finalizing is necessary when you play discs recorded with this unit on other DVD equipment. 1) Press [ GUIDER ] , to appear the Easy Guider menu.
Format Before you format the disc, please make sure nothing important is left on the disc, as all the disc contents will be erased. For DVD+RW,you can reformat the disc if you want to create a empty disc. 1) Press [ GUIDER ] , to appear the Easy Guider menu.
2) Press [p] [q] , to select the Format , then press [ENTER].
2) Press [p] [q] , to select the Finalize , then press [ENTER].
The recorder starts formatting the disc.
3) Press [ENTER] to start.
The recorder starts finalizing the disc.
N otes : During Format Finalize operating , you can select the EXIT to exit the Easy Guider menu.
3) When finish disc formatting , press [ENTER] to exit the format menu.

GUI Operation

Changing settings This chart shows the settings for this unit. Change the settings to suit your preferences and to suit the unit to the environment in which it is being used.
Aspect Ratio Settings of audio and video parameters when playing back. 16:9 Wide 4:3 Pan 4:3 L.Box Menu Langauge Select a menu operating language. ENGLISH, CHINESE, FRANCAIS, GERMAN, ITALIAN, SPANISH, Audio Langauge Select a audio operating language. ENGLISH, CHINESE, FRANCAIS, GERMAN, ITALIAN, SPANISH, Subtitle Langauge Select a subtitle operating language. ENGLISH, CHINESE, FRANCAIS, GERMAN, ITALIAN, SPANISH,
1) Press [SETUP] to appear the setup menu. 2) Press [p][q] to select System Playback Record Audio TV Tuner , and press [u] and press [u] or press [t] to return to preview layer. 3) Press [p][q] ,to select the item and press [u] or [ENTER]. 4) Press [p][q] , and to set the option and press [ENTER]. To exit the SETUP m enu Press [SETUP] or and press [t] till the main items and keep press to close.
Parental Set content control for supported DVD.Password is needed for the changing the setting. Set Level (Off , 1~8 ) Set Password (XXXX) Parental Set a system protect password. OLD Password (XXXX) NEW Password (XXXX) Confirm Slide Tim e Set the slideShow interval while playing JPEG files. Off 3~99 Seconds VCD PBC Enable/Disable Play Back Control for VCD and SVCD. ON OFF

System

Language Select a system operating language.
ENGLISH, TRADITIONAL CHINESE , SIMPLIFIED CHINESE, FRANCAIS, GERMAN, ITALIAN, SPANISH,
TV Type Select type of the TV output. NTSC PAL Date Set a Date of the system clock. MM/DD/YYYY (Month/Day/Year) Tim e Set a Time of the system clock. HH:MM:SS AM/PM Output Switch video output signal. S-Video Component Auto-Sleep Off/30/60/90/120mins
Record Quality Set the default quality of recording. HQ (1hr) SP (2hrs) EP (4hrs) SLP (6hrs) Chapter Mark Set the interval of chapter auto-insertion while recording. Off 2~15 mins
Progressive N otes : No video or distorted video will be displayed if the selected video output on the player is differ from the video output connection. 22

Digital Output Settings of digital audio output. PCM (Enable digital audio output with PCM data) Bit stream(enable digital audio output with encode data)
DTS Output Enable/Disable Digital Theater System output. ON (Enable Digital Theater System mode) OFF (Disable Digital Theater System mode)
TV Signal Select type of antenna input. Antenna Cable SCAN Enable/Disable Digital Theater System output. ON OFF Channel Fine Tune Adjust the channel frequency manually. -10 ~ -+1 ~ +10

Glossary

480i/480p Indicates the number of scanning lines and scanning format of an image signal. 480i indicates 480 scanning lines with interlace format, and 480p indicates 480 scanning lines with progressive format. Aspect ratio Aspect ratio refers to the length to height ratio of TV screens. The ratio of a standard TV is 4:3, while the ratio of a highdefinition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective. Bitstream The digital form of multi-channel audio data (e.g., 5.1-channel) before it is decoded into its various channels. Chapter / Title Chapter is the smallest division and title is the largest division on a DVD VIDEO. A chapter is a division of a title and similar to a track for Video CD or Audio CD. Com ponent video Video signals with three channels of separate information that makes up the picture. There are some types of component video, such as R/G/B and Y/Cb(Pb)/Cr(Pr). Com posite video A single video signal commonly used in most consumer video products that contains all luminance, color, and synchronization information. Dolby Digital (AC3) A six-channel system consisting of left, center, right, left rear, right rear and LFE (Low-Frequency Effect channel, for use with a sub-woofer) channels. It requires a Dolby Digital decoder, either in the player or in an external receiver to regenerate the sound. All processing is done in the digital domain. Not all Dolby Digital discs contain six (5.1) channels of information. DTS (Digital Theater System s) DTS stands for Digital Theater Systems. DTS is a Digital Surround audio encoding format configured with six (5.1) channels, similar to Dolby Digital. It requires a DTS decoder, either in the player or in an external receiver to regenerate the sound. All processing is done in the digital domain. Not all DTS discs contain six (5.1) channels of information. DVD-R DVD-R is a recordable disc that is the same size as a DVDVideo. Contents can be recorded only once to a DVD-R,and will have the same format as a DVD-Video. DVD-RW DVD-RW is a recordable and rewritable disc that is the same size as a DVD-Video. DVD-RW has two different modes: VR mode and Video mode.DVD created in video mode has the same format as a DVD-Video ,while discs created in VR(Video Recording)mode allow the contents to be programmed or edited. DVD+RW DVD+RW is a recordable and rewritable disc DVD+RW use a recording format that is comparable to a DVD-Video format. Interlace output NTSC, the video signal standard, has 480 interlaced (I) scan lines, The Interlaced scanning system places lines of the second half of the picture in-between lines of the first half of the picture. JPEG A popular file format for still image compression and storage. JPEG stands for Joint Photographic Experts Group. There are three sub-types of the JPEG format as follows. Baseline JPEG: used for digital cameras, the web, etc. Lossless JPEG: an old type, rarely used now. Linear PCM audio PCM stands for Pulse Code Modulation. Linear PCM is the usual method for digitally encoding audio without compression, and is used for the audio tracks on DVD VIDEO discs, Audio CDs, etc. MP3 MP3 (MPEG1 audio layer 3) is a compressed audio file format. Files are recognized by their file extension.mp3 or.MP3. MPEG MPEG stands for Moving Picture Experts Group. This is an international standard for compression of moving images. On some DVDs, digital audio has been compressed and recorded in this format. NTSC (National Television System Com m ittee) The initials stand for National Television Standards Committee. This is the committee that established the standards for television systems in the United States. The NTSC standard broadcasts 525 or 480 lines of resolution per second, and 30 frames per second of refresh rate, 60 Hz field frequency. NTSC TV system is widely used in USA, Canada, Latin America and Taiwan etc. PAL (Phase Alternation by Line) PAL (Phase Alteration Line) is the color television broadcast standard throughout the Western Europe (except in France, where SECAM is the standard), Australia, China, Singapore and Malaysia etc. It has 625 lines of vertical resolution per second and 25 frames per second refresh rate, 50 Hz field frequency. PBC Playback Control. A special feature on a Video CD or Super VCD that enables interactive use. S-Video A video signal which improves picture quality over standard composite connections. Used on Super VHS, DVD, high end TV monitors, etc. Track SVCD, VCD, Audio CD discs use tracks to divide up the content of a disc.

AC 100~240V , 50Hz/60 Hz 36 W +5C to +40C (+36F to +104F) 5% to 80% RH 420 x 66 x 268 mm 4.0 kg
N otes : The specifications and design of this product are subject to change without notice, due to improvement.
Quick Installation Guide (Side A)
Connection to a Television

ENGLISH

Rem ote Control & Setup Menu When you turn on the unit for the first time after purchase, press [SETUP] and follow the steps to set the unit. 1) Pres [ POWER ] to turn on the unit. 2) Press [SETUP] to appear the setup menu on the TV screen. 3) Press [p] [q] to select the System,Playback,Record,, Audio,TV Tuner of the setup menu. 4) Press [u] or [ENTER] and [p] [q] to select the item you want to change.

Sytem Setting

System Language Select system operating language.ENGLISH, TRADITIONAL CHINESE ,SIMPLIFIED CHINESE, FRANCAIS, GERMAN, ITALIAN, SPANISH. TV Aspect Select 4:3 Letter Box or 4:3 Pan Scan or 16:9 Wide Screen to suit your TV. Video Output There are 3 types of video outputs available on this unit, including S-Video, Component, Progressive. Connecting the correct video cable form the unit to the display unit and select the correct video output by pressing the [SETUP] button to setup. Audio Output This unit is capable of both analogue and digital audio output. Connect analogue audio output by connecting RCA cables to LR audio jack on the back of unit. For best audio effect, using digital optical cable to output the digital audio signal to the amplif ier with Dolby Digital & dts decoder.
Abo ut P la yback : Language : System Language (see page 22) Aspect Ratio: Playback TV Aspect (see page 22) Video out : System Output (see page 22) Audio out : Audio Digital Out (see page 23) Abo u t Re co r d : System Time : System Record Quality: Record Chapter Mark: Record TV Signal : Tuner

Record setting

Record Quality Set the default recording mode.Select a quality you want to record HQ , SP , EP , SLP.(see page 22) Chapter Mark Automatically divide a title(program) into chapters by inserting chapter marks at 2~15 minutes intervals during recording. (see page 22)

Date / Time (see page 22) Quality (see page 22) Chapter Mark (see page 22) TV Signal (see page 23)
5) Press [SETUP] to end the settings. No video or distorted video will be displayed if the selected video output on the player is differ from the video output connection.
Quick Installation Guide (Side B)

Disc Played

Disc Form ats Supported DVD-VIDEO/DVD-R/DVD-RW/DVD+R/DVD+RW/ CD-R/CD-RW/Audio CD/VCD/SVCD/JPEG/MP3 Video Form ats Supported MPEG2 for DVD and SVCD / MPEG1 for VCD JPEG file Audio Form ats Supported AUDIO CD / MP3 file
Recording from a TV , VCR or DV/V8
1) Press [SETUP] , to select RECORD and to set the
recording mode. ( HQ , SP , EP or SLP )
2) Put a empty DVD+R or DVD+RW on the tray, with the discs label facing up. 3) Press [SOURCE] , to select a AV- Input ( TV , AV1 , AV2 ,

S-Video, DV ).

4) Start play on the Video Cassette Recorder or DV/V8, or change the TV-channel. 5) Press [RECORD] , to record your video/audio from the
Video Cassette Recorder or DV/V8 ,TV program onto a DVD+R or DVD+RW.

Recordable Disc

Disc Form ats Supported DVD+R/DVD+RW

6) Press [

Basic Play
? Press [ POWER] , to turn on the unit. Press to switch the player on or to put in standby ? Press [ OPEN/CLOSE] , to open the disc tray and place the disc label-up on the disc tray. ? Press [ PLAY] , to start playback.
Setting the tim er m anually 1) Press [TIMER] , to appear the Timer Record menu
2) Press [t] [u] to Select an item and to set the date.
To set the Mode-->Onec-->Weekly-->Daily. To set the Date-->Month-->Day-->Year. To set the Start Time-->Hour-->Minute. To set the End Time-->Hour-->Minute. To set the Souce-->TV-->AV1-->AV2-->S-Video-->DV. To select the Quality-->HQ-->SP-->EP-->SLP. press [POWER] to turn off the unit and start to timer recording.
? Press [ F.F.] , to perform fast forward scanning. Press repeatedly to play the disc forward at 2x , 4x , 8x , 16x.
? Press [ REW.] , to perform fast reverse scanning. Press repeatedly to play the Disc reverse at 2x , 4x , 8x , 16x.
? Press [ NEXT] , to advance to the next chapter/ track. Press repeatedly to skip to the next chapter during playback. ? Press [ PREVIOUS] , to reverse to a previous chapter. Press repeatedly to return to the beginning of previous Chapters during playback ? Press [ ? Press [ PAUSE] , to pause playback. STOP] , to stop playback.

Firmware Update

As the firmware is continuously refined for greater stablity and compatiblity of the player, user may chose to update the latest firmware form http://www.liteonit.com.tw/liteweb/csd.htm All operation is written in PDF file. Please follow the instruction step by step to complete the firmware update.

? Press [TOP MENU] , to a disc menu appears on the TV screen. ? Press [MENU] , to a chapter menu appears on the TV screen.
Improper firmware update may cause system malfunctioning.

LVW-5001 / LVW-5005XS User's Manual
USA: LITE-ON (USA) International Inc. 42000 Christy Street, Fremont, CA 94538 Tel: 1-510-687-1800 Fax: 1-510-687-1900 Customer Call Center: 1-888-8-LITEON (1-888-854-8366) 1-866-269-5113 (French) Service e-mail: dc_support@liteonit.com
http://www.liteonit.com/DC/english/liteonit.htm

P/N 7819901179A

Table of contents

Getting started

Accessories... Important safety instructions.. Warnings, cautions and others.. Disk information... Audio CD recording.. 20

Timer recording

Setting the timer... 21

Controls and displays

Remote control... Front panel connections.. Display window.. Rear panel connections.. 6 7

Playback

Basic playback... POWER, OPEN/CLOSE, PLAY, F.F., REW. NEXT, PREVIOUS... PAUSE/STEP, STOP, DISPLAY.. TOP MENU, MENU.. Navigation operation.. SLOW, SEARCH.. A-B REPEAT,SUBTITLE.. AUDIO, ANGLE.. INFORMATION... 23 23

Connecting up

Connecting the antenna cable and television.. 8 For better picture... 9 Component out.. 9 S-Video out... 9 For better sound... 10 Connection to a stereo audio amplifier or receiver. 10 Connection to a digital audio device. 10 Digital out optical... 10 Digital out coaxial.. 10 Connecting satellite receiver or cable box.. 11
JPEG/MP3 file and Audio CD playback
JPEG file playback.. MP3 file playback.. Audio CD playback.. Slide show... 24 24

Quick setup

Initial setup.. Aspect ratio.. Video outptut... Audio... 12 12

Editing

DVD menu and Edit menu.. Naming a title... Protecting a title... Overwrite a title... Erasing a title... 25

TV channel setup

Automatic TV channel search.. Adding or deleting TV channel manually.. Fine-tuning TV channel manually.. Swapping TV channel manually (following TV).. Channel Editing... 14

Easy Guider

Playback... Record on DVD... Record on CD-R/CD-RW... VCD/SVCD/Audio CD recording. Erase... Finalize... 28 28

Recording

Before recording... Recording television programs... Adding new recordings... Changing chapter intervals.. Playback with the DVD menu.. Recording from a VCR or V8 / Hi8 / DV.. The front panel and rear panel connection.. DV recording... Use Easy Guider to record DV signal.. One touch record to record the DV signal. DV control... Record on CD-R/CD-RW discs.. Create a correct disc format.. VCD/SVCD recording.. 20 20
GUI operation Firmware update Glossary Specifications Troubleshooting Guide

Accessories

Please check and identify the supplied accessories. 1x Remote control 1x AC Power cord 2x Batteries
Important safety instructions

1) 2) 3) 4) 5)

Read instructions. Read all the safety and operating
instructions before operating the product. Retain instructions. Keep the safety and operating instructions for future reference. Heed warnings. Adhere to all warnings on the product and in the operating instructions. Follow instructions. Follow all operating and use instructions. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. Water and Moisture - Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product. Any mounting of the product should follow the manufacturers instructions and should use a mounting accessory recommended by the manufacturer. CART - A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. Ventilation - Slots and openings in the cabinet provide ventilation, ensure reliable operation of the product, and protect it from overheating. Do not block or cover these openings. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. Do not place this product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. Location - The appliance should be installed in a stable location. Non-Use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

DVD R/RW DVD R/RW Video CD (VCD) Super Video CD

(SVCD)

Audio CD (CD-DA)

CD-R/RW (JPEG/MP3)

Recordable Disc types Disc Types Logos DVD R/RW
Characteristics DVD R disc written in the DVD VR format. DVD RW disc written in the DVD VR format.

DVD R/RW

(LVW-5005XS model only)
DVD R disc written in the DVD VR format. DVD RW disc written in the DVD VR format. CD R/CD RW disc written in the MPEG1 or MPEG2 video format or written in PCM Audio mode. DVD Dual -- Written on both DVD DVD R/DVD RW disc. R/DVD RW/

CD R/RW

DVD DualTM & AllWriteTM
All Write Written on all recordable DVD disc and CD R/CD-RW disc.
Note: The DVD-Video/DVD+RW/DVD+R/DVD-R/DVD-RW/CD-R/CD-RW Logos are trademarks of the respective companys. For best result use discs with the above logos and that conform to specifications. The unit cannot play other discs correctly. Do not use irregular shaped discs (e.g. heart-shaped), as these can damage the unit. It may not be possible to play CD-R, CD-RW, DVD-R, DVD-RW, DVD+R, DVD+RW in all cases due to the type of disc or condition of the recording.
Video System (NTSC & PAL) This DVD-Recorder supports both NTSC&PAL system. Aspect Ratio 4:3 (Letter Box) Standard 4:3 Pan&Scan 16:9 (Wide-Screen) Others Audio : Appears at the beginning of a scene record with multiple audio languages. Subtitle : Appears at the beginning of a scene recorded

Unplayable disc types

The unit does not play back discs listed below. If you try to play back these discs, excessive noise may cause damage to speakers. 1) Unfinalized discs from other DVD-Recorder. 2) DVD-ROM, DVD AUDIO, CD-ROM, PHOTO CD, SACD 3) DVD-RAM, DVD-VR format Region Code of DVD-Video This unit can playback DVD-VIDEO discs compatible with the region code is printed on the rear of the unit. Examples of playable DVD-VIDEO discs: Notes: Audio System Dolby Digital Linear PCM
with multiple subtitle languages. Angle: Appears at the beginning of a scene recorded from multiple angles. All Write Technology (LVW-5005XS model only) ALL WRITE technology makes it alright to record on almost all of the recordable discs. (DVD+RW, DVD+R, DVD-RW, DVD-R, CD-RW or CD-R discs)
DTS (Digital Theater Systems) 4
Remote Control The Remote Control
1) 2) 3) 4) 5) 6) 7) 8) 9) Open/Close button ( CH OPEN/CLOSE)

button (Channel)

Display button (DISPLAY) Setup button (SETUP) Top menu button Easy Guider button ( Pause/Step button ( Play button ( PLAY) F.F/ REW.) Guider) PAUSE/STEP)

F.F./REW. button(

10) Source buttons ( SOURCE) 11) Record button ( RECORD) 12) Power button ( POWER)

Before using the unit, follow the steps below to connect the unit to the cable box and TV. Connecting to a satellite box or a cable box with COMPOSITE jacks Use a RF cable (supplied) to connect the RF IN on the cable box/satellite receiver to the antenna outlet. Use a RF cable (same as supplied) to connect the RF OUT on the cable box/satellite receiver to the RF input on the DVD Recorder. Use a RF cable (same as supplied) to connect the RF OUT on the DVD Recorder to the RF IN on the television. Use AUDIO/VIDEO cables (supplied) to connect the AUDIO/VIDEO output on the unit to the audio/video input on the television.

Initial setup

Remote control & Setup menu
Confirm the antenna is connected correctly, and follow the steps below to make the personal adjustments for using the DVDRecorder. 1. Press [ POWER] to turn on the unit. 2. Press [SETUP] to display the setup menu. 3. Press [ ] [ ] to select the System, Language, Playback, Record, Audio, TV Tuner and press [ ] or press [ ] to return to the previous or next menu. 4. Press [ ] [ ] to select the item that you want to change and press [ ] or press [Enter]. System --- Video Output System --- TV Type ---> Date ---> Time Language --- OSD Playback -- Aspect Ratio Audio --- Digital Output (PCM / Bit Stream) Record --- Quality ( HQ, SP, EP and SLP ) 5. Press [ENTER] to confirm the setting. 6. Press [SETUP] to exit the setup menu or press [ ] to return to the previous menu. Note: To record TV programs using the timer record feature, you must set the time accurately. Notes: You must connect to the component video input terminals on a 480P compatible television. 2. See t yT m?u ig[ ] or [ ] and press [ENTER]. lc se sn t 3. Select video output as COMPONENT or PROGRESSIVE using [ ] or [ ] and press [ENTER]. 4. When all settings are correct, press [ ] to return to the main menu. 5. To exit the setup menu, press the [Setup] button.

Progressive scan mode

You can change the video output mode when you press [SETUP] button and to select the System-->Video Output-->Progressive. (Video will not be displayed correctly if connected to an incompatible television.) Video output mode: 480I: Interlace video 480P: Progressive video

4.Press [ ] [ ][ ] [ ] to select the channel(s) that you want to add or delete and press [ENTER] to confirm it.
1.Ensure the antennas are securely connected to the DVD-Recorder. 2.Switch on the TV set and the DVD-Recorder. 3.Press [SETUP] to bring up the SETUP menu, press [ ] [ ] to select the TV TUNER and press [ ]. 4.Press [ ] [ ] to select Utilities and press [ ]. 5.Press [ ] [ ] to select START SCAN and press [ENTER] to start auto channel search.
Move the cursor to the TV channel and you can press [ENTER] again to cancel delete operation.
5.Press [ ] [ ][ ] [ ] to select EXIT and press [ENTER] to save setting and exit the add/ delete menu. Fine-tuning TV channel manually
After you have performed the automatic channel search you may like to fine-tune the TV channel signal manually. Follow the steps below to complete fine tune.
1.Press [SETUP] to bring up the SETUP menu, press [ ] [ ] to select the TV TUNER and press [ ]. 2.Press [ ][ ] to select FINE and press [ ]. 3.Press [ ][ ] to fine-tune the channel signal.
6.The auto TV channel search starts. The procedure may take a few minutes. 7.When all the TV channel have been searched and stored, press [SETUP] to exit. Adding or deleting TV channel manually
After you have performed the automatic channel search, you may like to add or delete some of the TV channels. This function allows adding or deleting channel manually.
Swapping TV channel manually (following TV)
This function allows users to manually swap the TV channel order stored in DVD-Recorder to match the TV channel order stored in users TV set.
1.Press [SETUP] to display the SETUP menu, press [ ] [ ] to select the TV TUNER icon and press [ ]. 2.Press [ ] [ ] to select Swap and press [ENTER] to bring up the SWAP menu. 3.Select the TV channel(s) to be swapped and press [ENTER] to mark it/them. 4.Press [ ] [ ][ ] [ ] to select a new channel position and press [ENTER] to swap.
1.Press [SETUP] to display the SETUP menu, press [ ] [ ] to select TV TUNER and press [ ]. 2.Press [ ] [ ] to select Uilities and press [ ]. 3.Press [ ] [ ] to select Add/Delete and press [ENTER] to bring up the add/delete menu.
5.To swap more TV channels, repeat step 3 to complete the settings. 6.Select EXIT to save the setting and exit the SWAP menu.

Channel Editing

Before channel editing
Ensure that the antenna cables are securely hooked up to the unit.
Inserting the TV channels 1.Press [EDIT] to bring up the Channel Editor menu, press [ ] [ ] to select one of the TV channels and press [ ]. 2.Press [ ] [ [ENTER]. ] to select Insert to and press
Adding or deleting TV channel manually 1.Turn on the TV set and the DVD-Recorder, and press [Source] to switch the input signal source of the unit to TV. 2.Press [EDIT] to bring up the Channel Editor menu, press [ ] [ ] to select one of the TV channels and press [ENTER].

employs the ALL WRITE technology to make it alright to record on almost all of the recordable discs. You may use DVD+RW, DVD+R, DVD-RW, DVD-R, CD-RW or CD-R discs to record. Please use qualified recordable DVD+R/RW disc to ensure the best recording quality. Check our website for the list of qualified discs.
Recording continues until you stop the recording or when disc is full.

To stop recording

When you press [ STOP], it may take a few moments for recording to stop and the session to close.
Note: 1.CD-R, DVD+R & DVD-R are write-once DVD discs. 2.CD-RW, DVD+RW & DVD-RW are re-writable DVD discs. 3.You cannot add new recording to a DVD-R/DVD-RW/DVD+R disc after the disc is finalized. 4.In some cases, you may not be able to add new recording to the recordable DVD discs that contain recordings recorded by other DVD-Recorders.

To pause recording

Press [ PAUSE] to pause recording, and press [ to resume recording. PAUSE]
Recording televison programs 1.Press [ POWER] to turn the unit on.
2.Press [ OPEN/CLOSE] to open the tray and insert a recordable DVD disc.
Press the button again to close the tray. When you insert a new recordable DVD disc, the DVD-Recorder will automatically start the disc preparation process.
3.Press [SOURCE] to change the signal-input source and select the TV input.
To change the recording mode.

Press [SETUP].

4.Press [ CH ] or press [ ] [ ] to select the channel you want to record.
Notes: The new setting cannot change the current recording mode but will be activated during the next session.

One-touch recording

Use one-touch recording to start recording immediately in 30 minute blocks. Each time you press the record button, the recording time is extended by another 30 minutes. Note: You can also use the number buttons to select a channel.
To check the disc status while recording
Press [DISPLAY] , the recording information appears.
5.Press [RECORD] to start recording.
After pressing [RECORD], it may take a few moments to initialize.
Adding new recordings Adding new recordings after other recording sessions. Press [RECORD] to start recording, and press [ STOP] at the point you want to stop. Playback with the DVD menu Selecting a recorded session on a disc

The front panel and rear panel connection
Connect a Video Cassette Recorder or Camcorder to the units input terminals.
2.Place a recordable DVD disc on the tray with the discs label facing up. 3.Press [SOURCE] to select the signal-input (TV, AV1-Front, AV2-Rear, S-Video, DV).

Notes:

4.Start to play on the VCR or Camcorder. 5.Press [RECORD] on the DVD-Recorder to record your video/audio signal from the VCR or V8 Camcorder onto a recordable DVD disc.

6.Press [

STOP] to stop recording.
Press [ PAUSE] to pause recording, and if you want to restart PAUSE] button to resume recording. recording, press the [
DV recording Before starting to record DV contents
This DVD Recorder allows basic DV control functions with the remote control. The DVD Recorder is equipped with a camcorder control (Play, Stop, FF or Reverse) feature via the DV Link connection. Simply move the screen cursor to the desired function and press [ENTER] on DV input screen.
Use Easy Guider to record DV signal 1.Power on your TV and this DVD-Recorder. 2.Place a recordable disc on the tray. Make sure the discs label is facing up. 3.Connect the DV cable (IEEE-1394 4-pin cable) to both the DV Camcorder and the DVD-Recorder.
8.Press [ ] [ ] to select DV Input, and press [ENTER] to confirm.
9.Press [ ] [ ] to select a recording quality and press [ENTER] to confirm.
10.Press [ENTER] to start recording.
Note: 1.The DV-Link input jack on this unit is for use with DV compatible camcorder only. 2.Only DV signals can be input to the DV-Link jack on this DVD Recorder. 3.Do not connect a MICRO MV format video camcorder to this DVLink (IEEE-1394) jack. 4.You cannot connect more than two pieces of video input sources at a time to the front panel connector of this DVD-Recorder.
Notes: This DVD-Recorder will stay in Pause mode when no DV input signal is detected.

11.To pause recording.

Press [ Press [ PAUSE ] on the remote control to pause recording. PAUSE ] again, if you want to resume recording.
4.Power on the DV Camcorder. Start Playback mode on the DV Camcorder. 5.Pause the DV Camcorder where you want to record. 6.Press [ GUIDER] on the remote control. This actives the Easy Guider menu. 7. Press [ ] [ ] and to select the RECORD icon, and press [ENTER] to confirm.

12.To stop recording.

Press [ STOP]
LVW-5001 model Before playing a DVD+R disc on compatible equipment, you will need to finalize the disc. LVW-5005XS model Before playing a DVD+R/DVD-R/DVD-RW disc on compatible equipment, you will need to finalize the disc.
One Touch Record to record DV contents Before starting to record DV contents
When you do not need to operate your DV, this unit allows basic DV control on DVD Recorder Remote control.
DV control After recording is stopped, a DV control bar will appear on the screen. This allows basic DV control utilizing the DVD Recorders remote control.
1.Power on your TV and this DVD-Recorder. 2.Place a recordable DVD disc in the tray. Make sure the discs label is facing up. 3.Connect the DV Cable (IEEE-1394 4-pin cable) to both the DV Camcorder and the DVDRecorder. 4.Power on the DV Camcorder. Set Playback mode on the DV Camcorder. 5.Pause the DV Camcorder where you want to record. 6.Press [SOURCE] to change the Signal-Input source and select the DV input. 1.Press [ ] [ ] to select ( the DV Camcorder. 2.Press [ ] [ ] to select ( Camcorder. 3.Press [ ] [ ] to select ( Camcorder playing. 4.Press [ ] [ ] to select ( Camcorder playing. 5.Press [ ] [ ] to select ( Camcorder playing. 7.Resume DV Camcorder playback and press [RECORD] to start recording. ) , to fast-forward

) , to rewind the DV

) , to stop the DV ) , to start the DV ) , to pause the DV

8.To pause recording.

9.To stop recording.
Recording (LVW-5005XS model only)
Record on a CD-R/CD-RW disc Before starting to record
This DVD Recorder is a versatile unit that can record video in either VCD / SVCD or audio CD format on CD-R/RW discs. Please use qualified recordable disc to ensure the best recording quality. Check our website for the list of qualified discs. Note: 1.You cannot perform any recording before you the CD-R/CD-RW disc is prepared. 2.Only single format is allowed on a single disc. 3.You cannot change the format of CD-R disc after the disc preparation process. 4.To change the format of a CD-RW disc, you must use the erase function to create a new format. 5.All contents on the disc will be erased after the disc preparation process.
Note: Ensure to activate the erase function before you started to record.
Creating a correct disc format Place an empty CD-R or CD-RW disc on the tray 1.Press [ GUIDER ] to display the Easy Guider menu, press [ ] [ ] to select the Erase and then press [ENTER].
4.Press [GO] to record your signal onto the disc.

5.Press [

Press [ PAUSE] to pause recording. If you want to restart recording, press the button or [RECORD] again.
Recording mode (an empty 700MB disc)
Audio CD recording To start audio track recording 1.Place a CD-R / CD-RW disc prepared in the audio CD format on the tray with the discs label facing up.

2.Press [ ] [ ] to select which recording format to record and then press [ENTER]. 3.When the disc preparation process is completed and the format is created, select Exit and press [ENTER] to exit the erase menu. VCD/SVCD recording To start recording 1.Place a well-prepared CD-R or CD-RW disc onto the disc tray with the discs label facing up. 2.Press [ GUIDER ] to display the Easy Guider menu, press [ ] [ ] to select Record and then press [ENTER]. 3.Press [ ] [ ] to select the signal-input ( TV, AV1-Front, AV2-Rear, S-Video, DV ) and press [ENTER].
2.Press [ GUIDER ] to display the Easy Guider menu, press [ ] [ ] to select the Record and then press [ENTER]. 3.Press [ ] [ ] to select the audio signal input ( TV, AV1-Front, AV2-Rear, S-Video, DV) and press [ENTER]. 4.Press [RECORD] to record your audio signal onto a recordable CD disc. 5.Press [EDIT] to create a new audio track into disc during recording. 6.Press [ STOP] to stop audio recording.
Note: 1.Press the [Edit] button once, a new audio track will be automatically created by 2-sec interval. 2.Audio source input during the 2-sec interval will be recorded as the beginning of the new track.

Timer record

Prior to timer record
Please check that the recordable DVD disc or recordable CD disc (LVW-5005XS model only) has enough space for the timer recording function. Before you start to record, follow the steps to set the date, time, picture quality and channel of the program manually.
8.Press [ ] [ ] to set End Time and then press [ENTER] to set the Recording end time. 9.Press [ ] [ ] to select Source and then press [ENTER] to set the Recording source.
TV <-->AV1-Front<-->AV2-Rear<-->S-Video<-->DV
Setting the timer 1.Press [ POWER] to turn the unit on.
2.Press [ OPEN/CLOSE] to open the tray and place a recordable DVD disc or recordable CD disc (LVW-5005XS model only) on the tray.
If you use an new recordable DVD disc, disc preparation process will take place in the background automatically.
10.Press [ ] [ ] to select Quality and then press [ENTER] to set the Recording quality.
LVW-5001 model only: Mode: HQ <-> SP <-> EP <-> SLP LVW-5005XS model only: Mode:HQ <-> SP <-> EP <-> SLP <-> SVCD<->VCD<-> Audio CD
3.Press [TIMER] to display the Timer Record menu.

Note:: Multiple angles must be available on the DVD-disc. (within the current title) or track for playback.

INFORMATION

To enable or disable the DVD/VCD/SVCD disc information.

A-B REPEAT

Starting to repeat a desired part. Select Point A at the beginning of the part you want to repeat. Select Point B at the end of the part you want to repeat. The unit locates A and starts repeat playback between A and B. Select [Cancel]. The A-B repeat mode turns off, then normal playback continues.

To exit the Navigation

Press [ mode. Navi.] again or [ ] to exit the Navi
The unit can play an Audio CD, JPEG, or MP3 file on a disc.
Audio CD playback JPEG file playback Playing JPEG files 1.Place the JPEG disc on the tray.
The disc will begin playback automatically.
Playing Audio CDs 1.Place the Audio CD on the tray.
2.Press [ ] or [ ] to advance to the next picture, or return to the previous picture.
2.Press [ NEXT] or [ PREVIOUS] to advance tracks or return to previous track. 3.Press [ 4.Press [ PAUSE] to pause the playback. STOP] to stop the playback.
5.Use the number buttons (0~9) to select the desired audio track, and press [ENTER].
Begin playing from a selected track.
3.Press [ ][ ] to select Rotate RIGHT or Rotate LEFT and Rotate UP or Rotate DOWN.
Slide show Concurrent playback of JPEG and MP3 files on the same disc. 1.Place the disc on the tray.
4.Press [ playback. 5.Press [
PAUSE] to pause the picture STOP] to stop the picture playback.
2.Press [ PLAY ] to start playback. NEXT ] or [ PREVIOUS ] to 3.Press [ advance to the next or previous MP3 files.
Or press [ ] [ ] to skip the picture.
MP3 file playback Playing MP3 files 1.Place the MP3 disc on the tray.
4.Press [ ][ ] to select Rotate RIGHT or Rotate LEFT and Rotate UP or Rotate DOWN. 5.Press [ playback.
PAUSE] to pause the slide show
STOP] to stop the slide show playback.
2.Press [ NEXT ] or [ PREVIOUS ] to advance to the next or return to previous MP3 files.
Note: 1.If an MP3 file name includes any two-byte character, the unit may not display the file name correctly. 2.The unit cannot support ID3 tag. 3.The unit does not support MP3-Pro or WMA files. 4.The unit supports discs recorded with multiple sessions. 5.The unit can only play back pictures or tracks with the following file extensions; JPG or jpg and MP3 or mp3 etc. 6.The time required for reading disc contents may vary for different discs. It depends on the number of groups (folders) and tracks (files) recorded, etc. 7.You cannot advance or reverse playback by pressing F.F. or REW. during JPEG/MP3 disc playback. 8.You cannot play audio track by pressing the number buttons during MP3 disc playback. 9.This unit supports MP3 file bitrates of: 32Kbps ~ 320Kbps.

3: PG 6: R Off

Password Set a system protection password. Password is needed for the change of setting. OLD Password (XXXX) *(Default:0000) NEW Password (XXXX) Confirm (XXXX) Slide Time Set the slide show interval while playing JPEG files. Off 3~99 Seconds VCD PBC Enable/Disable play back control for VCD and SVCD. ON OFF

Record

Record Quality Set the default quality of recording. HQ (1hr) SP (2hrs) LP (3hrs) EP (4hrs) SLP (6hrs) *(Default:SP) Chapter Mark Set the interval of chapter auto-insertion while recording. Off 5/10/15/20/25/30 mins *(Default:5 mins)
Note: Video will not be displayed if the selected video output on the player is different from the video output connection. 29

GUI Operation

Firmware update
As the firmware is continuously refined for greater stablity and compatiblity of the player, user may update the latest firmware form http://www.liteonit. com/DC/english/download.htm All operations are written in PDF file. Please follow the instructions step by step to complete the firmware update. Caution:
Improper firmware update may cause malfunction of the system.
Digital Output Settings of digital audio output. PCM (Enable digital audio output with PCM data) Bit Stream (Enable digital audio output with encode data)
DTS Output Enable/Disable Digital Theater System output. ON (Enable Digital Theater System mode) OFF (Disable Digital Theater System mode)

TV Tuner

TV Signal ---> Antenna, Cable or auto (Select the type of antenna input) Country ---> Select your location Utilities ---> Start Scan or Add/Delete or Swap (Select to start rescaning channel or add/delete a channel or to swap the TV channel ) Fine --> -24 ~ -+1 ~ +24 (Select to fine-tune the channel frequency manually)

Glossary

480i/480p Indicates the number of scanning lines and scanning format of an image signal. 480i indicates 480 scanning lines with interlace format, and 480p indicates 480 scanning lines with progressive format. Aspect ratio Aspect ratio refers to the length to height ratio of TV screens. The ratio of a standard TV is 4:3, while the ratio of a high-definition or wide TV is 16:9. The letter box allows you to enjoy a picture with a wider perspective. Bitstream The digital form of multi-channel audio data (e.g., 5.1-channel) before it is decoded into its various channels. Chapter / Title Chapter is the smallest division and title is the largest division on a DVD VIDEO. A chapter is a division of a title and similar to a track for Video CD or Audio CD. Component video Video signals with three channels of separate information that makes up the picture. There are some types of component video, such as R/G/B and Y/Cb(Pb)/Cr(Pr). Composite video A single video signal commonly used in most consumer video products that contains all luminance, color, and synchronization information. Dolby Digital A six-channel system consisting of left, center, right, left rear, right rear and LFE (Low-Frequency Effect channel, for use with a subwoofer) channels. It requires a Dolby Digital decoder, either in the player or in an external receiver to regenerate the sound. All processing is done in the digital domain. Not all Dolby Digital discs contain six (5.1) channels of information. DTS (Digital Theater Systems) DTS stands for Digital Theater Systems. DTS is a Digital Surround audio encoding format configured with six (5.1) channels, similar to Dolby Digital. It requires a DTS decoder, either in the player or in an external receiver to regenerate the sound. All processing is done in the digital domain. Not all DTS discs contain six (5.1) channels of information. DVD-R DVD-R is a recordable disc that is the same size as a DVD-Video. Contents can be recorded only once to a DVD-R,and will have the same format as a DVD-Video. DVD-RW DVD-RW is a recordable and rewritable disc that is the same size as a DVD-Video. DVD-RW has two different modes: VR mode and Video mode.DVD created in video mode has the same format as a DVD-Video ,while discs created in VR(Video Recording)mode allow the contents to be programmed or edited DVD+R DVD+R is a recordable disc that is the same size as a DVD-Video. Contents can be recorded only once to a DVD+R,and will have the same format as a DVD-Video. DVD+RW DVD+RW is a recordable and rewritable disc. DVD+RW use a recording format that is comparable to a DVD-Video format. Interlace output NTSC, the video signal standard, has 480 interlaced (I) scan lines, The Interlaced scanning system places lines of the second half of the picture in-between lines of the first half of the picture. JPEG A popular file format for still image compression and storage. JPEG stands for Joint Photographic Experts Group. There are three sub-types of the JPEG format as follows. Baseline JPEG: used for digital cameras, the web, etc. Lossless JPEG: an old type, rarely used now. Linear PCM audio PCM stands for Pulse Code Modulation. Linear PCM is the usual method for digitally encoding audio without compression, and is used for the audio tracks on DVD VIDEO discs, Audio CDs, etc. MP3 MP3 (MPEG1 audio layer 3) is a compressed audio file format. Files are recognized by their file extension.mp3 or.MP3. MPEG MPEG stands for Moving Picture Experts Group. This is an international standard for compression of moving images. On some DVDs, digital audio has been compressed and recorded in this format. NTSC (National Television System Committee) The initials stand for National Television Standards Committee. This is the committee that established the standards for television systems in the United States. The NTSC standard broadcasts 525 or 480 lines of resolution per second, and 30 frames per second of refresh rate, 60 Hz field frequency. NTSC TV system is widely used in USA, Canada, Latin America and Taiwan etc. PAL (Phase Alternation by Line) PAL (Phase Alteration Line) is the color television broadcast standard throughout the Western Europe (except in France, where SECAM is the standard), Australia, China, Singapore and Malaysia etc. It has 625 lines of vertical resolution per second and 25 frames per second refresh rate, 50 Hz field frequency. PBC Playback Control. A special feature on a Video CD or Super VCD that enables interactive use. S-Video A video signal which improves picture quality over standard composite connections. Used on Super VHS, DVD, high end TV monitors, etc. Track SVCD, VCD, Audio CD discs use tracks to divide up the content of a disc.

MEDIA TYPES SUPPORTED (Read Only): DVD-R/RW, DVD+R/RW, DVD-ROM, CD-R/RW, CD-ROM AUDIO RECORDING FORMAT DVD+VR (HQ/SP/n0 193ru.3g6-4cl4EP/SLP): Dolby Digital 2channel VCD/SVCD: MPEG1 layer 2 CD-DA: PCM
RECORDABLE DISC SUPPORTED: 1) DVD+R ( DVD+VR Mode ) 2) DVD+RW ( DVD+VR Mode ) 3) DVD-R ( DVD+VR Mode ) 4) DVD-RW ( DVD+VR Mode ) 5) CD-R ( SVCD/VCD Format ) 6) CD-RW ( SVCD/VCD Format )
VIDEO RECORDING QUALITY Mode Time Bit Rate Encode HQ 1hr 9.5Mbps MPEG2 SP 2hrs 5.1Mbps MPEG2 EP 4hrs 2.5Mbps MPEG2 SLP 6hrs 1.7Mbps MPEG1 SVCD 34mins 2.5Mbps MPEG2 VCD 68mins 1.15Mbps MPEG1
TUNER TV format NTSC 720X480 720X480 352X480 352X240 352X480 352X240 PAL 720X576 720X576 352X576 352X288 352X576 352X288
CONNECTIONS FRONT PANEL Video Input Audio L/R Input IEEE 1394 Input REAR PANEL Video Input Audio L/R Input S-Video Input
AUDIO RECORDING QUALITY Bit Rate Mode Audio CD 1.41 Mbits/sec

Sampling Rate 44.1KHz

RCA Connector (yellow) x1 RCA Connector (white/red) x1 4-Pin Mini DIN x1
VIDEO RECORDING FORMAT MPEG2: DVD+VR (HQ/SP/LP/EP mode), SVCD MPEG1: DVD+VR (SLP mode), VCD
TV STANDARD & VIDEO RESOLUTION NTSC 60Hz 525 lines PAL 50Hz 625 lines
Video Output Audio L/R Output S-Video Output Component / Progressive Scan Output Digital Audio Output
RCA Connector (yellow) x1 RCA Connector (white/red) x1 4-Pin Mini DIN x1 Y, PB, PR (Green/Blue/Red) x1 Coaxial Optical x1 x1

352 pixels 576 lines

GENERAL Power Supply Power Consumption Operating Temperature Operating Humidity Dimensions(W/H/D): Net Weight:
AC 100~120V 60 Hz Approx. 36 W +5C to +40C (+36F to +104F) 5% to 80% RH 420 x 66 x 268 mm Approx. 2.8 kg
Note: The specifications and design of this product are subject to change without notice.
VIDEO PERFORMANCE DA Converter 10-bit/54MHz 33

Troubleshooting Guide

Picture The image from this unit does not appear on the television.
--> Make sure that the TV is connected to the AUDIO/VIDEO terminal, SCART-S-VIDEO out terminal or COMPONENT VIDEO OUT terminals on this unit. (refer to CONNECTING UP section) --> Make sure that the televisions input setting is correct. --> Make sure that a disc is well-placed on the disc tray and is compatible to the local TV system (NTSC or PAL) --> Check whether the recorder is set to progressive with an incompatible TV. Reset by pressing [ ], 5, 0, 0, and 1 on the remote control and then press [ENTER].
No playback on DVD recorder.
--> Theres no recording on the disc. Check the disc first. --> A unplaybackable disc type is inserted. Check the playable disc type list. --> The way you inserted the disc is wrong. Insert the disc with the label side facing up. If theres no label on the disc, check the disc retailer. --> Wrong region code: The region code on the recorder and the disc must match. --> Parental control is on: you have to unlock it first. (default code of the recorder: 0000) --> Check of the cables are secured between the TV set and the recorder.

The image from this unit appears with noises.
--> The disc is distorted or flawed. --> If the picture output signal from the recorder passes through your VCR to get to your TV, or if you are connected to a combination T V/VIDEO player, the copy protection signal applied to some DVD programs could affect picture quality. If you still experience this problem even when you connect your recorder to your TV, try connecting your recorder to your TVs S-VIDEO output.
Timer Recording Timer recording does not work properly.
--> The timer program is incorrect. Correct the program. --> Different timer program times overlap. --> The clock setting is wrong. Go to setup to set the right time and date. --> An already finalized DVD+R has been inserted: change disc.
The image from an external input is distorted.
--> If the video signal from the external component is copyprotected, you can not connect via the recorder. Connect the component directly to your TV.
The timer program remains even after recording finishes.
--> The timer program remains if set to daily or weekly.

Sound There is no sound

--> Check the audio cable connection. --> Check if the audio cord is damaged. --> The input source setting on the amplifier is incorrect. --> Theres no sound when the picture is paused or during scanning (even forwards at regular playback speed) or slow motion play. Press [PLAY] to resume regular playback. --> If the audio signal does not come through the DIGITAL OUT (OPTICAL or COAXIAL) jacks, check the AUDIO OUT settings.

Recording Cannot record.

--> You havent inserted a disc or the disc you inserted cannot be recorded on. Insert a disc the unit can record onto.
An alternate audio track cannot be recorded.
--> Second Audio Program (SAP) is not available for all programs. --> The recorder does not feature Second Audio Program (SAP) function.
The sound from this unit is not presented properly or is distorted.
--> Check the audio cable connection. --> Check if the audio cord is damaged. --> Make sure that the amplifier/receiver or TV is set to the correct input and the volume is turned on. --> If the sound is distorted, try cleaning the cable plugs.
Recording does not start immediately after you press the [RECORD] button.
--> Disc preparation process is taking place and will take a short while. (applicable to DVD-R/RW and DVD+R/RW discs)

TV channel TV channels cannot be changed.
--> Switch the input signal source of the recorder to TV. --> Connect the antenna cables correctly.
Playback Cannot play back a disc recorded using this recorder or another player
--> If the disc was recorded in video mode, make sure that its finalized. --> Some players will not play recordable DVD discs when recorded in video mode and finalized. --> Discs recorded with copy-once material cannot be played on non-CPRM compatible players.
Others The disc tray does not open/close.
--> Contact your local dealer or local authorized service facility.
The unit stops at HELLO and does not respond to any other commands.
--> Turn the unit off and turn it on again. If the unit still does not respond to any commands, unplug the power cord, reconnect it and turn it on again. Contact local dealer or authorized service facility if the unit still does not work.
The recorder starts playing the disc automatically.
--> The DVD VIDEO features an auto playback function.