ISO 9001 CERTIFIED

www.liteputer.com.tw

DX-610/626

6CH. DMX DIMMER PACK
Lite-Puter Enterprise Co., Ltd.
WEBSITE: www.liteputer.com.tw E-MAIL: sales@liteputer.com.tw
Lite-Puter DX-610/626 [EUM-E]

Safety Introductions.. 2

Chapter 1.Introduction of DX-610/626
1-1 1-2 1-3 1-4 1-5 1-6 Feature... 3 Brief device introduction.. 3 Specification.. 3 Front panel.. 4 Output terminal board / Sockets panel. 4 Wiring Diagram.. 6

Chapter 2Operation

2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 Standard DMX512 Signal.. 6 DMX start address setting.. 6 Dimming/Switching setting. 7 Warm up setting (06%).. 7 Channel output status preview.. 7 Manual dimming.. 8 Display the dimming value of DMX channel, internal temperature.. 8 DMX status & DMX address.. 8

SAFETY INTRODUCTIONS

Please note the load power
Please refer to the data we suggest to ensure the normal total working hours of DX-610/626 1. If DX-610/626 is installed in a rack, please make sure the rack is airy. Otherwise the machine will become over-heat and result in the mis-function. DX-610: the max. output of each channel if 10A: For testing (DO Not over 30 minutes) DX-626: the max. output of each channel if 20A: For testing (DO Not over 30 minutes) 3. DX-610: the output of each channel is8A: For several hours use (Theaters, Stages) DX-626: the output of each channel is16A: For several hours use (Theaters, Stages) 4. DX-610: the output of each channel is 8A: Can work for the whole year without switching off (Hotels, Restaurants, Buildings) DX-626: the output of each channel is 12A: Can work for the whole year without switching off (Hotels, Restaurants, Buildings)

Working Environment

1. Temperature Under 35C 2. If the machine is installed in a rack, then the temperature inside the rack must be under 45C 3. Humidity40% --- 80%

Suggested Dimming Lights

Incandescent lamps, halogen lamps, low volt halogen lamps with ballast.

Chapter 1.

1-1 Feature
Introductions of DX-610/626
6 dimming channels. Auto tracking of frequency and phase. Temperature control device: When the temperature is over 35the fan will start automatically. Auto tracking of frequency: Enables stable dimming output in different frequencies. Testing function: Can do test without connecting a console. Warm-up function to protect the loads. (Warm-up setting 0---6.0%)
1-2 Brief device introductions
DX-610: 10A no fuse breaker. DX-626: 25A no fuse breaker. Fan for temperature controlling to sink heat and clean the dust inside. (37CFM X 1) The front panel can be dismantled easily for quick repair.

1-3 Specification

Power Output AC100-240V, 45-63Hz, 34W, 12W DX-610: Maximal output is 10A each channel DX-626: Maximal output is 20A each channel (Please refer to the user manual) DMX signal output/ input DMX signal connector Analog signal power input Analog input channel DMX512/ 1990 XLR 5Pin, RJ11-6p4c phone jack DC 0-10V 9 channels PIN 1~6( CH1~6, PIN 7(NC, PIN 8(V+12V OUT,PIN 9(GND Analog signal connector D-Type Plug 9Pin(F)
Dimension Location Weight 1-4 Front panel
482(W) x 88(H) x 300(D)mm 19" 2U standard rack 8Kg

CH1 CH2 CH3 CH4 CH5 CH6

DMX OUT

ANALOG IN 0~10VDC

PIN1~6:CH1~CH6 PIN7:NC PIN8:V+12V OUT PIN9:GND

ON FNC DMX

1:V+12V 2:Data+ 3:Data4:GND

DMX IN

CONTROL OFF

(1) Power on/ off switch

(5) (6) (7)

Function Key

(2) DMX OUT/ IN (5 pin) (3) DMX IN (RJ11, phone jack)
Dimming VR of Channel 1- 6 No fuse breaker (Channel 1-3)
(4) LED display/ function keys
(8) No fuse breaker (Channel 4-6)
1-5 Output terminal board / Sockets panel

TERMINAL TYPE

13 (12) Power input terminal board. (DX-610: 20A Single phase; DX-626: 40A Single phase)
(9) DMX connector (RJ11, phone jack)

(10) DMX IN

(XLR-3 pin)
(13) Output terminal board (10A each channel, External power no fuse
4 Lite-Puter DX-610/626 [EUM-E]

(11) DMX OUT (XLR-3 pin)

breaker is necessary when mounting.)

AMERICAN TYPE

Output sockets (DX-610: 10A each channel; DX-626: 15A each channel,External power no fuse breaker is necessary when mounting.)

SCHUKO TYPE

Output sockets (DX-610: 10A each channel; DX-626: 16A each channel,External power no fuse breaker is necessary when mounting.)

1-6 Wiring diagram

5 Lite-Puter DX-610/626 [EUM-E]
3 PHASES 4 WIRES N THE BEST WIRING DIAGRAM R S T

E N V1 V2 V3

SINGLE PHASES 2 WIRES
There are 3 PHASES 3 WIRES and SINGEL PHASE 3 WIRES as option.

Chapter 2.

Operation

Standard DMX512 Signal

This point flashing when receiving DMX
DMX start address setting
STEP-1 holdingDMX, pressorto find the start address.
: move 1 number forward : up to Channel 512
: move 1 number backward :down to Channel 1
DX-626 is a 6 channel dimmer pack so when setting this unit: 1 as C.001, the output is from Channel 1 Channel 6. 2 as C.007, the output is from Channel 7 Channel 12. 3 It is allowed for setting more than 1 piece of DX-626 at the same start address.
Dimming/Switching setting
STEP-1 pressDMXkey into DMX status STEP-2 press and hold theFNCkey for 3 sec. Default settingall channel are dimming mode
STEP-3 pressFNCkey to select channel STEP-4 pressorto select dimming mode or switching mode

(dimming)

(Switching)

warm up setting (06%)

STEP-1 pressFNCkey
STEP-2 pressFNCkey to select the setting channel, EX :select channel 1 STEP-3 press,key to adjust Channel 1 set on 6% for warm up
Channel output status preview
STEP-1 Enter to DMX status and pressDMXkey STEP-2 pressorto preview

Manual dimming

STEP-1 PushVR1-VR6to do the prompt dimming output of individual channel. When there is another signal inputting from a console, it will take the higher value as the output.
Display the dimming value of DMX channel,

internal temperature.

PressLto display the dimming value of DMX channel. PressTto display the internal temperature.
DMX status & DMX address
a.pressDMXto DMX status b.10 minutes unused of unit, the DMX will activate to DMX status