2000_9_8_30_LIT

2/2/01

4:47 PM

Page 1

SAVE THIS MANUAL

Self-Cleaning Litter Box
INSTALLATION AND OPERATION MANUAL IMPORTANT INFORMATION INSIDE!
Please read prior to product installation and operation.

Page 2

WELCOME TO THE LITTERMAID BRAND FAMILY!

QUICK SETUP INSTRUCTIONS

s s s s s s s s s Fill only with premium clumping litter just below the full line. Do not overfill or unit will not operate properly. Do not use crystal or pearl-like types of litter. Unpack power supply and cord from carton. Unpack paw cleaning ramp (optional) and brush from cardboard at top of unit. No tools required, unit is fully assembled. Peel off protective tape which holds litter tray closed. Cut to remove restraints on both ends of the rake. Attach power cord to unit and plug into outlet or insert 8 D cell batteries (batteries not included). s Attach the paw cleaning ramp (optional) by inserting one pin into one of the side holes, at the waste receptacle end, then stretch the other pin to insert in the other side hole. (For further information, see Installing Paw Cleaning Ramp). s Install a waste receptacle by lifting the waste receptacle compartment cover area and inserting a waste receptacle as described in the Waste Receptacle Installation instructions. s Turn the unit on and let it cycle once to smooth out the newly poured litter. s Acclimate the cat to LitterMaid litter box! NOTE: Wipe sensor lenses (located inside of the side panels) with a soft cloth to keep sensors dust free (Fig. 5).

IMPORTANT SAFEGUARDS

s Not intended for use with kittens under six months, unless they are capable of jumping in and out of the litter box on their own. s Not intended for use by handicapped, incapacitated or very old cats that might experience difficulty in entering or leaving the litter box. s For cat use only! The LitterMaid Self-Cleaning litter box is intended solely for the safe elimination of cat waste. DO NOT ATTEMPT TO USE THIS PRODUCT FOR ANY OTHER PURPOSE. s PREGNANT WOMEN and IMMUNE-DEFICIENT PEOPLE should avoid contact with cat waste at all times. s CAUTION: THIS IS NOT A TOY. LitterMaid Self-Cleaning litter box is a precisionoperated appliance. Should the rake become jammed during cleaning, THIS UNIT CONTAINS A MECHANISM THAT WILL AUTOMATICALLY STOP, REVERSE AND RESTART THE CLEANING OPERATION. s Never allow small children to play in or around this device. Please read all directions in this manual carefully prior to operating this product.

SAVE THESE INSTRUCTIONS

ACCLIMATING YOUR CAT HOW THE LITTERMAID SELF-CLEANING LITTER BOX WORKS:
s s s s Cat enters the unit, triggering the sensor, setting the timer for the cleaning cycle. After 10 minutes, the raking cycle begins and scoops out clumps. Rake opens lid and deposits clumps into waste receptacle. Seated waste receptacle allows for safe and easy disposal of waste when full. If your cat needs to acclimate to the new LitterMaid Self-Cleaning litter box, follow these instructions: 1. Place the LitterMaid unit next to your old litter box. 2. Set it to run automatically. 3. Do not clean out the old litter box. (Cats prefer to use a clean box and the LitterMaid litter box will always be clean.) If your cat is shy then do not operate the LitterMaid litter box automatically for 2-3 days. Manually activate the LitterMaid litter box 2-3 times a day for the first 2 to 3 days to let your cat get used to going in the LitterMaid litter box before you set it to clean automatically. 4. As soon as your cat is acclimated to the LitterMaid litter box, set it to clean automatically and remove the old litter box. Note: Do not place the LitterMaid litter box product in a wet environment or in direct sunlight.

Page 4

TROUBLESHOOTING
A. Improper operation. Probable Cause: s Too much litter or dusty sensors. 1. Check to make sure litter in tray is not above the FULL LINE. 2. DO NOT OVER FILL. 3. Wipe each lens cover with a soft dry cloth to remove dust from sensors. B. Unit does not completely clean litter box. Probable Cause: s Low-quality clumping litter. 1. Do not use crystal/pearl-like types of litter. 2. Use only a premium grade of clumping litter. C. Unit does not operate when power switch is switched On. Probable Cause: s Incorrectly installed or dead batteries s Faulty AC adapter s Faulty or non-activated outlet s Power outage To determine cause: 1. IF UNIT WAS RUNNING ON BATTERY POWER: a. Turn On/Off switch to Off. b. Open battery compartment and check that battery is installed correctly. c. Try to operate the unit. It should perform a complete cleaning cycle. d. If unit does not operate, replace batteries and try again. e. If unit fails to operate with fresh batteries, try it with the AC adapter. f. If unit STILL fails to operate, call Customer Service at 1-800-LIT-MAID (548-6243) for additional assistance. 2. IF UNIT WAS OPERATING WITH AN AC ADAPTER AND FAILS TO FUNCTION: a. Turn unit off and check the following: 1. The adapter plug is inserted fully into the input jack. 2. The power outlet is operating. (You may wish to double-check by plugging unit into another outlet.) b. Wait a few seconds and turn unit On again. The unit should perform a complete cleaning cycle. c. If unit still does not operate, turn unit Off and unplug adapter. d. Operate the unit on battery power ONLY. 1. If it does not operate, call Customer Service at 1-800-LIT-MAID (548-6243) for additional assistance. D. Waste clumps adhered to the surface of litter tray. Probable Cause: s Soiled litter tray surface. 1. If necessary, remove litter tray and clean with mild detergent, rinse and dry.

2. For future use, spray litter tray surface with a silicon spray and wipe with a soft, damp cloth. This will help difficult-to-remove waste clumps from adhering to the surface. NEVER SPRAY WITH WATER OR IMMERSE MAIN CASING IN WATER. E. Light fails to come on when unit is activated. Probable Cause: s Power outage or batteries incorrectly installed. 1. Slide On/Off switch to Off and then back to On. 2. Make sure you have power to the unit and/or batteries are properly installed. F. Light blinks slowly and continuously. Probable Cause: s Rake has encountered an obstacle it cannot remove. 1. Be sure to dispose or empty receptacle when full, so as not to jam raking mechanism. 2. Make sure rake teeth are clean and free of litter. See instructions under ALARMS. G. Light blinks quickly Probable Cause: s Batteries need replacing. H. Light is off completely. Probable Cause: s No AC power is reaching unit or batteries are dead. See procedure 1 or 2 under Problem C. I. More help and information are available by calling Applica Customer Service at 1-800-LIT-MAID (548-6243).

Page 6

INSTRUCTIONS FOR USE
PRODUCT MAY VARY SLIGHTLY FROM ILLUSTRATIONS Safety Bar (not shown) Rake Sensors Restraints
INSTALLATION OF WASTE RECEPTACLE
1. Insert waste receptacle into disposal area of the unit. 2. Be sure the two notched corners on the bottom of the waste receptacle rest on the horizontal posts of the unit. 3. Slip the edge of the waste receptacle 5 TABS UNDERNEATH the ridged tabs of the unit, making sure it snaps in place securely. (See inset Fig. 4.) INSTALLING LID: 1. Lift the waste compartment cover and position the waste receptacle lid with its two round fasteners FIG. 4 extending downward. 2. Insert the two raised areas into the two round openings in the waste receptacle compartment cover. 3. PUSH each raised area of the lid into its corresponding opening. (See inset Fig. 4.) 4. Close cover. The raised areas on waste receptacle lid should extend through the waste compartment cover by approximately 1/2 inch. REMOVING WASTE RECEPTACLE See instructions under CARE AND CLEANING. INSTALLING (OPTIONAL) PAW CLEANING RAMP The paw cleaning ramp has two pivot pins. The unit has two holes located on the sides of the waste receptacle end of the unit. 1. Position the paw cleaning ramp with fabric side facing up. 2. Point the pivot pins toward the waste receptacle end of the unit. 3. Lift the paw cleaning ramp and insert one of the pivot pins into one of the holes. 4. Slightly stretch the other pivot pin to reach the other hole, then insert (Fig. 1). Be careful not to overstretch. Tug slightly on paw cleaning ramp to assure ramp is secure.

Battery Compartment (batteries not included) Red Power Indicator Light AC Adapter Power Jack On/Off Switch Side Panels Latch Cleaning Brush

Litter Tray

Waste Receptacle Compartment Cover

FIG. 2 FIG. 1

FIG. 3
UNPACKING: s Remove unit from carton. s Remove all tape wrapped around battery compartment and waste receptacle compartment. s Remove the unit including insert that protects the rake during shipping. s Using scissors or wire cutters, carefully remove restraints around rake assembly. PLEASE NOTE: Remove protective strips of clear tape from the unit.

SET UP INSTRUCTIONS

WARNING: This unit does not require as much litter as a non-automated litter box. DO NOT OVER-FILL! Add more litter when the level drops to the "ADD LITTER" line. 1. Fill the litter box to the FULL LINE line with premium clumping litter. Do not pack litter down. NOTE: It is extremely important that only a premium brand of clumping litter is used for proper operation. 2. Slide Power Switch to the Off position. 3. Plug in the AC power adapter (Fig. 2) or install 8 D-cell batteries. (Batteries not included) (Fig. 3). a. Open battery compartment by pressing release tabs on compartment edge. b. Remove the top of the compartment. 6

Page 8

c. Install batteries as indicated on diagram inside compartment. Close battery compartment (Fig. 3). Should an AC power failure occur with batteries installed, the unit will operate normally. If operated solely on batteries, power should last approximately 1 to 2 months, depending on number of cats and frequency of use. 4. Make sure Disposable Waste Receptacle is secured (Fig. 4). 5. Wipe sensor lenses with a soft cloth to keep sensors dust free (Fig. 5).

CARE AND CLEANING

SENSOR COVERS: After changing or adding litter, always wipe each sensor cover with a soft, dry cloth to remove dust. The two sensors located on the interior side panels (Fig. 5) are protected by sensor covers that need to be kept dust-free. PAW CLEANING RAMP (Optional): 1. Remove the paw cleaning ramp by gently pulling on the fabric strip provided. 2. Clean by using a vacuum cleaner. 3. To return it to its original position, slide the fabric under the tabs. It is not necessary to remove the plastic ramp to clean the mat Do not use soaps or chemical cleaners, as they may be harmful to your cat. LITTER BOX: Use ONLY premium-quality clumping litter. Other litter quality will impair performance. Litter tray can be easily detached from unit for trouble-free complete cleaning and refilling. To empty and refill litter tray: 1. Check to make sure rake is in home position (close to the battery box). 2. Slide the On/Off switch to the Off position. 3. Unplug and remove batteries to prevent accidental activation of unit while it is being cleaned. 4. Pull out the lower part of the latches on both sides of unit (Fig. 6) and, using the handles on the top assembly, lift up. This will separate the tray from the main housing (Fig. 7). 5. Dispose of the clumping litter and wipe the tray with a damp cloth. If further cleaning is necessary, the litter tray can be fully immersed in water and washed with a mild detergent. To ensure proper disposal of clumping litter, follow manufacturers instructions on litter package. IMPORTANT: Do not soak or immerse the main housing in water. Dry the unit completely before reassembly.

FIG. 5

s s s s
Slide the power switch to the On position, red light will illuminate. Rake will automatically undergo one complete cleaning cycle. Unit is ready for use! Complete cleaning cycle will begin 10 minutes after sensor is triggered. Note: Unit will not start a cycle when cat is in the box.
s If the cat re-enters and leaves the litter box before the initial 10 minutes have elapsed, the timer will automatically reset and delay the beginning of the cleaning cycle for an additional 10 minutes. s Rake will stop and reverse if the safety bar touches and object that has gotten behind the rake while it is returning to its home position. ALARMS: Battery operated: Fast blinking red light indicates batteries require replacement. Light will continue to blink until batteries are removed or completely dead. If the rake cannot move an obstacle during the cleaning cycle, the unit will rake up to five times in an attempt to clear the obstacle. If unsuccessful, the rake will return to its home position, and the red light will blink slowly (approximately every second) indicating that the rake has encountered an obstacle it cannot move. If this happens, remove the obstacle, then slide the switch to the Off position for 5 seconds and back to the On position. The rake will then undergo a complete cleaning cycle. When cycle is finished, unit is ready for use. 7

Sensors

OPERATING INSTRUCTIONS
SAFETY FEATURES AND ALERTS
Tray FIG. 6 FIG. 7 Main Housing
6. Before replacing litter tray, spray litter tray surface with a silicon spray or baby oil and wipe with a soft, dry cloth. This will help to prevent difficult-to-remove waste clumps from adhering to the surface of the tray. 7. Refill litter tray to the FULL LINE with premium clumping litter only. 8. To reassemble, place the litter tray on a flat surface. Lower the main housing onto the litter tray carefully. Engage the two locks by pressing the lower part of each 8

Page 10

latch firmly against tabs on litter pan until a click is heard to indicate that both sections are locked in place. 9. IMPORTANT: Wipe any dust off the two sensors. 10. Plug in the AC power adapter and/or replace batteries. 11. Slide the On/Off switch to the On position to reactivate automatic operation. REMOVING WASTE RECEPTACLE: 1. Depress the two raised areas extending through the openings in the compartment cover. 2. Detach the disposable waste receptacle lid from the cover of the waste receptacle compartment. 3. Lift the compartment cover, exposing the closed waste receptacle assembly. 4. Pull the waste receptacle compartment cover edge free from tabs holding it in place and lift out. 5. To dispose of waste receptacle compartment cover, press in on four corners of lid to secure lid to the waste receptacle, and dispose. 6. If you wish to reuse the waste receptacle compartment cover, remove it for cleaning and reinstall after cleaning. Avoid contact with any waste material. We recommend wearing rubber or latex gloves while handling used waste receptacle. Disposable waste receptacles are available in packages of 12 and may be purchased through your local retailer or by visiting us at our web site at www.littermaid.com or calling us at 1-800-LIT-MAID. We will be happy to assist you in any way we can.

8. Clean rake with a soft cloth using warm water and a mild detergent. Do not use scouring pads or harsh or abrasive chemicals. Spray rake lightly with a silicon spray or baby oil before reinstalling. Note: Use the cleaning brush to clean the rake quickly and easily. REINSTALLING RAKE 1. Align the 4 slots on the rake with the screws on the rake assembly housing and push to snap in place. Press firmly at the base of the rake, so that it clicks onto the rake assembly housing, indicating the rake has been properly installed. 2. Rake needs to be snapped in completely. There should be no space between the edge of the rake and the rake assembly housing. If necessary retighten screws no more than 1/8 of a turn. 3. If using with an adapter, plug unit in, batteries may be reinstalled. 4. Switch the power switch to the On position. 5. Unit is ready to resume initial cleaning pass and is ready for operation.

Need Help?

For service, repair, or any questions regarding your appliance, call the appropriate 800 number listed below. Do NOT return the product to the place of purchase. Do NOT mail the product back to the manufacturer nor bring it to a service center. You may also want to consult the website listed below.
RAKE REMOVAL FOR CLEANING OR REPLACEMENT
RAKE : The rake can be removed for cleaning or replacement. NOTE: We suggest wearing rubber or latex gloves while handling the soiled rake. 1. Flip waste receptacle compartment cover open Screws (Fig.8). 2. With AC power adapter plugged in, or batteries installed, turn unit On. 3. Rake will automatically undergo the initial cleaning pass. 4. As rake climbs up the incline near the waste receptacle compartment cover, quickly move FIG. 8 the On/Off switch to the Off position and unplug the AC power adapter and remove batteries. 5. Place fingers on underside of the rake and gently pull the rake up and out toward waste receptacle compartment cover. Notches on rake bar detach from screws on the rake assembly housing (Fig. 8). 6. If rake fails to unsnap, use a Phillips screwdriver to loosen screws on underside of the rake assembly. Loosen no more than 1/8 of a turn. 7. Unsnap rake.

FULL ONE-YEAR WARRANTY

Applica warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse, or repairs performed by unauthorized personnel. If the product should become defective within the warranty period, or you have questions regarding warranty or service, call Customer Service and Information listed below. This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.

CUSTOMER SERVICE

If you should have any questions regarding the installation, operation or use of this product, visit our web site, www.littermaid.com, call or write to: Applica Consumer Products Consumer Assitance 6 Armstrong Road Shelton, CT 06484 1-800-LIT-MAID (548-6243) When calling, be sure to press the appropriate prompt regarding your concerns.

Page 12

Distributed by:

Pub No.175282-00RV01

6 Armstrong Road Shelton, CT 06484 Printed in Hong Kong

R12000/9-8-30

LM500 (LIT/SPE) LM600 LM700 LM750 LM800 LM900 LM950

IDEAL FOR EXTRA-LARGE CATS OR MULTIPLE CAT HOUSEHOLDS
Register your product online at www.prodprotect.com/applica, for a chance to WIN $100,000! For US residents only

USA/Canada 1-800-LITMAID

(548-6243) www.littermaid.com
Accessories/Parts (USA/Canada) 1-800-738-0245
Please Read and Save this Use and Care Book

Model LME9000MB

WELCOME TO THE FAMILY!
Congratulations on your purchase of the LitterMaid Advanced Automatic Self-Cleaning Litter Box. This product is designed to make caring for your cat a simpler, less time-consuming process. OPERATING INSTRUCTIONS FOR THE LITTERMAID SELF-CLEANING LITTER BOX Cat enters the unit; once he/she leaves, the sensors are triggered, setting the timer for the cleaning cycle (sensors need to be blocked for at least 5 seconds). Important: Unit will not start a cleaning cycle while cat is in the box. As soon as the cat leaves the litter box, the sensors activate the 10-minute countdown and the ionic air cleaner. The ionic air cleaner stays on during the countdown and the cleaning cycle. After the 10-minute countdown, the cleaning cycle starts and the rake scoops out the waste clumps. If the cat reenters and leaves the litter box before the initial 10 minutes have elapsed, the timer will automatically reset and delay the beginning of the cleaning cycle for an additional 10 minutes. Note: Rake stops and reverses if the safety bar touches any object that has gotten behind the rake while it is returning to its home position. Rake opens waste receptacle compartment cover and deposits clumps into the waste receptacle. Note: Rake stops and reverses if it encounters an obstacle larger than 35 lb. It will try five times to clear the obstacle. If obstacle is not cleared, the rake reverses back to the home position and the green POWER LED blinks (1 time per second). Sealed disposable waste receptacle allows for safe and easy disposal of waste when full. If the sleep timer is activated, the rake will not cycle for 9 hours from the set sleep mode time (the ionic air cleaner will automatically turn on every hour for 10 minutes). Important: When the On/Off button is in the Off position it only disables the rake function.
Instructions pertaining to a risk of fire, electric shock or injury to persons. WARNING: When using electric appliances, basic precautions should always be followed including the following: 1.Read all the instructions before using the appliance. 2.To reduce the risk of injury, close supervision is necessary when an appliance is used near children. 3.Do not contact moving parts. 4.Only use attachments recommended or sold by the manufacturer. 5.Do not use outdoors. 6.To reduce the risk of electric shock, do not put LitterMaid Advanced Automatic Self-Cleaning Litter Box in water or other liquid. Do not place or store appliance where it can fall or be pulled into a tub or sink. 7.NOT INTENDED FOR USE WITH KITTENS UNDER SIX MONTHS. 8.Not intended for use by handicapped, incapacitated or very old cats that might experience difficulty in entering or leaving the litter box. 9.PREGNANT WOMEN and IMMUNE-DEFICIENT PEOPLE should avoid contact with cat waste at all times. 10.CAUTION: THIS IS NOT A TOY. The LitterMaid Advanced Automatic Self-Cleaning Litter Box is a precision-operated appliance. Should the rake become jammed during cleaning, THIS UNIT CONTAINS A MECHANISM THAT WILL AUTOMATICALLY STOP, REVERSE AND RESTART THE CLEANING OPERATION. 11.For cat use only. The LitterMaid Advanced Automatic Self-Cleaning Litter Box is intended solely for the safe elimination of cat waste. DO NOT ATTEMPT TO USE THIS PRODUCT FOR ANY OTHER PURPOSE. 12.Never allow small children to play in or around this device. 13.Please read all directions in this manual carefully prior to operating this product.

IMPORTANT SAFEGUARDS

Intended for Household Use Only. SAVE THESE INSTRUCTIONS.
Product may vary slightly from what is illustrated.

Accessories

1. ON/OFF button. Important: When the On/Off button is in the Off position it only disables the rake function. 2. Timer 3. Warranty board 4. Battery compartment cover (Part# LME9000MB-01) (batteries not included) 5. Blue LED ionizer light 6. Ionic air cleaner 7. Motor housing 8. Removable rake (Part# LME9000MB-02) 9. Litter tray (Part# LME9000MB-03) 10. Sensors (both sides) 11. Waste receptacle compartment cover with flaps (Part# LME9000MB-04) 12. Receptacle supports Right (Part# LME9000MB-06) and Left (Part# LME9000MB-05) 13. Top housing 14. Plug holes for Plug 2 (1 each side) 15. Cutout handle (1 each side) 16. Plug holes for Plug 1 (1 each side) Consumer replaceable/removable parts

4. LitterMaid triple-action tool (Part# LME9000MB-10) 5. Paw cleaning ramp (LME9000MB-11) 6. Carbon Filters (4 included) (Part# LMF200) (12 pk.) 7. Disposable waste receptacle (4 included) (12 pk.) (Part# LMR200) (18 pk.) (Part# LMR300) Consumer replaceable/removable parts
1. Tent plugs type 1 and 2 (4) set (Part# LME9000MB-07) 2. Cleaning brush (Part# LME9000MB-08) 3. AC adapter (Part# LME9000MB-09)

Setup Instructions

No Tools Required for Setup Unpack the pieces of the unit listed below. Peel off the protective tape on the battery compartment. Cut or remove the tie restraints on the underside of unit.
1.Press down. 2.Slide through.
Before getting started be sure you have all of the following contents. Litter tray Top housing 1 1
1. Green LED POWER indicator light 2. Red LED SLEEP indicator light 3. Digital clock 4. Time/Programming buttons
Waste receptacle compartment supports Waste receptacle compartment cover Rake AC adapter (packed in styrofoam) Disposable waste receptacles Carbon filters LitterMaid triple-action tool Use and care manual Tent type 1 and 2 Plugs Cleaning brush (packed with disposable waste receptacles) Quick Start Sheet Paw-cleaning ramp
Other LitterMaid Accessories
Check our online service for parts and accessories at www.littermaid.com or call 1-800-548-6243 LitterMaid Kitty Kabana litter box cover (white) LitterMaid Elite litter box cover (white) LitterMaid litter box carpet LitterMaid hard clumping cat litter Disposable waste receptacles (12 pk.) Disposable waste receptacles (18 pk.) Carbon filters (12 pk.) Model # LMT200 LMT250 LMC100 LML100 LMR200 LMR300 LMF200
Assembly 1. Slide receptacle supports (marked L (left) and R (right)) into grooves on the bottom tray until they lock into place (A). A 2. Place both left and right flaps flat on top of the waste receptacle compartment panel. 3. Push the flaps in and up until they click into place (B). B 4. Lift the flaps until they lock into place (C). J H
Attach the waste receptacle lid by inserting the push tabs into the round holes. To secure, press on positions indicated (H).
Make sure lid edges are under the cover tabs (J).
C 5.Snap each pivot of the waste receptacle compartment cover, one at a time, into notches in the receptacle supports (D). 6.Open waste receptacle compartment cover. Important: Waste receptacle compartment cover must be opened to remove and install top housing. 7. Lift top housing. Angle into position bracket end of top housing under tray ledge. Important: 5 black tabs of the tray should be on top of the grey bar in front of the top housing (E). Bring the other end of top housing down so that it snaps into place. Check to be sure top housing is positioned securely on the tray. If positioned correctly, you will not be able to read writing on silver tray ledge. 8. Insert waste receptacles. Open waste receptacle compartment cover. Insert a disposable waste receptacle into the waste receptacle compartment. Insert the edge of the waste receptacle in an inclined position and place it between the edge of the tray and the bar of the top housing (F). Press the waste receptacle down into position (G). There should be no gap between the unit and the waste receptacle.

9. Install carbon filter. Peel off the paper strip on the carbon filter to expose the adhesive. Place filter adhesive-side down in the diamond-shaped insert in the center of the waste receptacle lid (K). Close the waste receptacle compartment cover. K 10. Fill the LitterMaid litter box with litter to just below the Full Line marked inside of litter tray Important: Use only hard clumping litter. Do not use non-clumping litter, crystal or pearl-like litters. Recommended Hard Clumping Liters LitterMaid Hard Clumping Cat Litter World's Best Cat Litter ARM & HAMMER Super Scoop The Baking Soda Clumping Litter Fresh Step Scoopable Premium Cat Litter EVER CLEAN Premium Clumping Litter Do not overfill the unit or it will not operate properly. Use the Fill Line on the LitterMaid triple-action tool to check that the litter is at the correct level in the center of the unit (L). L The LitterMaid Triple-Action Tool This handy 3-way tool helps you: Measure the level of litter (M). M
Assists in cleaning the rake in case it's needed (N).
N Aids in the removal of small waste particles (P). 1 1. Install paw cleaning ramp: The paw-cleaning ramp has two pivot pins that fit into holes on the sides of the waste receptacle compartment cover. Position the paw-cleaning ramp with carpet-side facing up. Insert the pivot pins into the holes (Q). Tug slightly on the ramp to ensure that it is firmly in place.
Q Install rake 1 2. Align tracks on back of rake (each end) and slide into grooves on motor housing (R).
R 1 3. Remove the AC adapter from where it is packed in the styrofoam and plug it into the unit (S). Plug the cord into a standard electrical wall outlet. Press the ON/OFF button to turn unit ON. The rake will automatically run through its first cleaning cycle and smooth out the litter.
Important: When the On/Off button is in the Off position it only disables the rake function. 14. Place the 4 tent plugs into the 4 holes on top housing. Note: Always use both hands to move LitterMaid litter box by holding handle cutouts located on each side of the tray. OPTIONAL PROGRAMMABLE TIME FUNCTION: The timer function allows you to deactivate the unit for up to 9 hours at your convenience. Once the time is up, it will restart again and run one cycle. To program the timer, you must first set the clock. Setting the clock 1.Set the clock to the time of day by pressing the hour then minute button. 9

Note: If setting P.M., be sure light in the upper left corner of the display is lit. The LED continues to blink 12:00 until the clock is set. Programming the Timer Sleep mode deactivates the cleaning cycle for a period of 9 hours. During this time the ionic air cleaner automatically turns on for 10 minutes every hour to freshen the air. After 9 hours the unit will perform one litter raking cycle and then resume normal operation. The 9-hour sleep mode and the 15-hour normal operation repeat at set time every 24 hours. To Program the Sleep Mode Timer (T) 1.Set the clock to the time of day by pressing the hour then minute button. Note: If setting P.M., be sure light in the upper left corner of the display is lit. The LED continues to blink 12:00 until the T clock is set. 2.Press the SET button on the control panel to begin programming. 3.Sleep mode red LED starts blinking. 4.Press the HOUR and MINUTE button (light indicating P.M. is in the upper left corner of the LED display) to set the time you want the sleep mode to begin (for example, if you set the time for 10:00 P.M. the unit remains in the sleep mode until 7:00 A.M. (9 hours). 5.Sleep mode time is automatically accepted if no buttons are pressed for 3 seconds or more. 6.Sleep mode red LED stops blinking and red LED is not lit. 7.Sleep mode is now set but is not activated. To Activate Sleep Mode 1.Press and hold the set button. 2.Steady red light comes on to indicate that the sleep mode is activated. To Deactivate Sleep Mode 1.Sleep mode must be activated (red LED lit) to be deactivated. 2.Press the SET button, steady red LED is no longer lit. Ionic Air Cleaner As soon as the cat leaves the litter box, the sensor activates the 10-minute countdown and the ionic air cleaner. The ionic air cleaner stays on during the countdown and the cleaning cycle. If the sleep timer is activated the rake will not cycle for 9 hours from the set sleep mode time but the ionic air cleaner will automatically turn on every hour for 10 minutes. Optional Items: For more information, call 1-800-738-0245 or visit our website: www.littermaid.com 10
Helpful Information If you need to acclimate your cat to the LitterMaid Advanced Automatic Self-Cleaning litter box, refer to "Acclimating Your Cat" in this use and care book. Unit will work without setting the clock when unit is turned on. If your unit is not working properly, refer to "Troubleshooting" in this use and care book. Batteries (We recommend using batteries only as a back-up): Push up on center ridges to open battery compartment door. Remove the battery door. Follow the diagram in the compartment to install 8 AA Alkaline cell batteries (batteries not included). Just as your alarm clock continues to run on batteries if there is a power failure, the LitterMaid litter box will continue to operate as long as batteries are installed. Change the batteries periodically. Sensors Sensors (located on interior side panels) must be kept clean. Wipe sensors with a soft, dry cloth to keep them dust free (U). U

If your cat is shy, do not operate the LitterMaid litter box automatically for 2 to 3 days. Do it manually by pressing the ON/OFF button once and then turning it off. Manually activate the LitterMaid litter box 2 to 3 times a day for the first 2 to 3 days, to let your cat get used to going into the LitterMaid litter box, and how it sounds and works; you can then set it to clean automatically. As soon as your cat is acclimated to the LitterMaid litter box, set it to clean automatically. Press the ON/OFF button to ON and remove the old litter box. Note: Do not place your LitterMaid litter box in a wet environment or in direct sunlight. Do not use outdoors or on patios.

Care and Cleaning

This product contains no user serviceable parts. Refer service to qualified service personnel. Sensor Covers The two sensors located on the interior side panels are protected by sensor covers that need to be kept dust free. After changing or adding litter, wipe each sensor with a soft, dry cloth to remove dust. Litter Tray Use only hard clumping litter. Low quality or non-clumpling litter will impair performance and may damage your unit. To empty and clean litter tray: Check to make sure rake is in home position. Press the ON/OFF button to turn unit OFF. Important: When the On/Off button is in the Off position it only disables the rake function. Unplug unit and remove batteries to prevent accidental activation of the unit. Remove the waste receptacle. Remove the rake. Remove the top housing. Dispose of the used litter. To ensure proper disposal of litter, follow manufacturer's instructions on litter package. Wipe the litter tray with a damp cloth. If further cleaning is necessary, the litter tray can be fully immersed in water and washed with a mild detergent. Important: Do not soak or immerse the top housing in water. To clean wipe with damp cloth. Dry the unit completely before reassembling. Before reassembling, spray litter tray surface with nonstick cooking spray or silicone spray, and wipe with a soft, dry cloth. This will help to prevent waste clumps from adhering to the surface of the tray. Removing Disposable Waste Receptacle We recommend avoiding contact with waste material. Wear rubber or latex gloves when handling used disposable waste receptacle. 12
LED operation, function and why they blink:

Green on control panel Blinking green on control panel Blue on ionizer Red on control panel Blinking red on control panel Power LED indicator is lit when power to the unit is on. LED is located on control panel. LED blinks (2 times per second) indicating batteries are low. LED blinks (1 time per second) when the rake assembly has encountered a blockage. Ionic air cleaner LED (behind the rake) is only lit when the ionizer is operating. Sleep timer LED is continually lit when sleep mode is activated. Occurs during the sleep mode programming.
ACCLIMATING YOUR CAT To acclimate your cat to the new LitterMaid Advanced Automatic Self-Cleaning litter box, we suggest following this procedure. Place the LitterMaid unit next to your old litter box. Set it to run automatically by pressing the ON/OFF button ON. Important: When the On/Off button is in the Off position it only disables the rake function. Do not clean out the old litter box. Cats prefer to use a clean box, and the LitterMaid litter box will always be clean. 11
Depress the two push tabs in the waste receptacle compartment cover (V) to detach the disposable waste receptacle lid from the waste receptacle compartment cover. Lift the compartment cover, exposing the closed disposable waste receptacle assembly. Press in on four corners of lid to secure lid to the waste receptacle, pull up from both sides making sure to hold lid and receptable together; lift out and dispose (W). Disposable waste receptacles are available in packages of 12 or 18 and may be purchased through your local retailer, by visiting us at our website at www.littermaid.com, or by calling us at 1-800-738-0245. We will be happy to assist you in any way we can.

Troubleshooting

Rake continues to go through cleaning cycles. Probable Cause: Too much litter in the litter box is causing excess litter to collect behind the rake, preventing it from returning to home position or there is an obstacle in front at the rake. If the rake cannot move an obstacle during the cleaning cycle, the unit will go through a cleaning cycle up to five times in an attempt to clear the obstacle. If unsuccessful, the rake will return to its home position, and the green light will blink slowly (1 time per second), indicating that the rake has encountered an obstacle it cannot move. Solution: 1. Press the ON/OFF button to turn unit OFF. Important: When the On/Off button is in the Off position it only disables the rake function. 2.Clear the obstacle. Be sure litter in tray is just below the "Full Line". Level litter on litter tray evenly and use the LitterMaid triple-action tool to measure the level of the litter in the center of the unit. Full Line will not be visible if tray is overfilled. 3. Press the ON/OFF button ON. 4.The rake will run through a complete cleaning cycle. When cycle is finished, the unit is ready for use. Unit does not operate 10 minutes after cat leaves. Probable Cause: Dusty sensors Solution: 1.Wipe each sensor with a soft, dry cloth. 2. Press the ON/OFF button to turn unit OFF. Important: When the On/Off button is in the Off position it only disables the rake function. 3. Press the ON/OFF button ON. 4.Unit will run through a cleaning cycle.

Rake Removal & Cleaning Removing the rake: The rake can be removed for easy cleaning. We recommend wearing rubber or latex gloves when handling the soiled rake. Be sure rake is in the home position and unit is turned off. Grasp rake ledge underneath logo and slide up and off of unit. Clean rake with a soft cloth using warm water and mild detergent. Do not use scouring pads or harsh or abrasive chemicals. Spray rake lightly with nonstick cooking spray or a silicone spray before reinstalling. Note: Rake may be cleaned while installed by using the LitterMaid triple-action tool. Paw-Cleaning Ramp: The carpet is made of 100% polypropylene and latex foam. To Clean: Remove mat by gently pulling on the fabric strip provided (X). The mat is held in place by 5 tabs and will remove easily. Remove and clean carpet by using a vacuum cleaner. To return it to its original position, reinsert carpet under the X tabs. It is not necessary to remove the plastic ramp to clean the mat. Note: For small stains, moisten a sponge with mild detergent and cold water; wipe to clean. Do not use soaps or chemical cleaners, as they may be harmful to your cat. Caution: Do not place carpet in washer or dryer. Do not vacuum carpet when it is wet.
Unit does not completely clean litter box. Probable Cause: Low-quality litter. Solution: 1.Do not use non-clumping, crystal or pearl-like litter. 2.Use only hard clumping litter. Unit does not operate when you press ON/OFF button to turn unit ON. Important: When the On/Off button is in the Off position it only disables the rake function. Probable Cause: Power outage Faulty or non-activated outlet Old batteries Solution: Check batteries and outlet Use batteries in case of power outage Switch to battery power Probable Cause: Incorrectly installed or dead batteries. Change the batteries once yearly (batteries should only be used as backup). Solution: 1. Press the ON/OFF button OFF. 2.Open battery compartment; check to see that batteries are correctly installed. 3. Press the ON/OFF button ON. The unit should perform a whole cleaning cycle. 4.If unit does not operate, replace batteries with fresh ones and try again. 5.If unit does not operate with fresh batteries, try it with the AC adapter. 6.Green light should come on. If it does not, there is a problem with the AC adapter or batteries. Probable Cause: AC adapter does not work

Solution: Press ON/OFF button OFF and check the following: Important: When the On/Off button is in the Off position it only disables the rake function. 1.The AC adapter plug is inserted fully into the input jack. 2.The power outlet is operating. (you may wish to double-check by plugging unit into another outlet). 3.Wait a few seconds and turn unit on again. Green light should come on and the unit should perform a complete cleaning cycle. 4.If unit still does not operate, press ON/OFF button OFF and unplug the AC adapter. 5.Operate the unit on battery power only. Waste clumps adhere to the surface of the litter tray. Probable Cause: Soiled litter tray surface Solution: (We recommend wearing rubber or latex gloves when handling waste). 1.Remove clumps with scoop and dump litter into another container. 2.Remove litter tray (refer to "Care and Cleaning" in this use and care book), clean with mild detergent, rinse and dry. 3.Spray litter tray surface with nonstick cooking spray or silicone spray, and wipe with a soft, dry cloth. This will help to prevent waste clumps from adhering to the surface of the tray. Wait until tray is completely dry and assemble unit again. Power light fails to come on when ON/OFF button is pressed ON. Important: When the On/Off button is in the Off position it only disables the rake function. Probable Cause: Power outage or batteries are incorrectly installed or dead. Solution: 1. Press ON/OFF button OFF then back ON. 2.Make sure there is power to the unit and/or fresh batteries are correctly installed.
If you cant solve the problem using this Troubleshooting section, more help is available by calling Customer Service at 1-800-LIT-MAID (548-6243). Power light blinks slowly and continuously. Probable Cause: Rake has encountered an obstacle it cannot remove. If the rake cannot move an obstacle during the cleaning cycle, the unit will go through a cleaning cycle up to five times in an attempt to clear the obstacle. If unsuccessful, the rake will return to its home position, and the green light will blink slowly (approximately every second), indicating that the rake has encountered an obstacle it cannot move. Solution: 1. Press ON/OFF button OFF. Important: When the On/Off button is in the Off position it only disables the rake function. 2.Use the LitterMaid triple-action tool to remove the obstacle. 3.Make sure that the rake teeth are clean and free of litter. Use the LitterMaid tool to clean rake teeth. 4. Press ON/OFF button ON. Power light blinks quickly. Probable Cause: Batteries need replacing. Solution: Light will continue to blink until batteries are removed or until they are completely dead. If SLEEP timer light is off. Solution: 1.Check to be sure clock is set to the correct time. 2.Check to see if the sleep mode is set and activated, see "Programming the Sleep Timer " section.

If the rake is stuck in the center or dumping position. Solution: 1. Press ON/OFF button OFF. Important: When the On/Off button is in the Off position it only disables the rake function. 2.Unplug unit. 3.Remove batteries. 4.Clean unit (check track for litter). 5.Wipe sensors. 6.Put unit together and plug into AC power only and press ON/OFF button to turn unit ON for the automatic cycle. If the Rake stops in the dump position Press ON/OFF button OFF Examine the Home position switch for obstruction (litter) preventing the switch lever arm from releasing Carefully remove the obstruction using tooth pick or dental instrument Press ON/OFF button turn unit ON The rake should automatically return to the Home position. If not, contact the Consumer Assistance Number for direction If blue LED ionizer light is off. Solution: Ionizer only turns on during 10-minute countdown and raking cycle. Ionizer only turns 10 minutes every hour during sleep mode.
NEED HELP? For service, repair or any questions regarding your appliance, call the appropriate "800" number on the cover of this book. Do not return the product to the place of purchase. Do not mail the product back to the manufacturer nor bring it to a service center. You may also want to consult the website listed on the cover of this manual. Two-Year Limited Warranty (Applies only in the United States and Canada) What does it cover? Any defect in material or workmanship; provided; however, Applicas liability will not exceed the purchase price of the product For how long? Two years after the date of original purchase What will we do to help you? Provide you with a reasonably similar replacement product that is either new or factory refurbished How do you get service? Save your receipt as proof of the date of sale. Check our on-line service site at www.prodprotect.com/applica, or call our toll-free number, 1-800-548-6243, for general warranty service or If you need parts or accessories, please call 1-800-738-0245. What does your warranty not cover? Damage from commercial use Damage from misuse, abuse or neglect Products that have been modified in any way Products used or serviced outside the country of purchase Glass parts and other accessory items that are packed with the unit Shipping and handling costs associated with the replacement of the unit Consequential or incidental damages (Please note, however, that some states do not allow the exclusion or limitation of consequential or incidental damages, so this limitation may not apply to you.) How does state law relate to this warranty? This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.
ARM & HAMMER and Super Scoop are registered trademarks of Church & Dwight Co., Inc. EVER CLEAN and Fresh Step are registered trademarks of The Clorox Pet Products Company

Copyright 2008 Applica Consumer Products, Inc. Made in Peoples Republic of China Printed in Peoples Republic of China

R22007/4-26-122E WIN