Before you start

Owners Manual
Recordable disc We strongly recommend for good recording quality: SONY DVD+RW 4x, MAXELL DVD+R 4x/8x/16x, SONY DVD+R 4x/8x/16x, TDK DVD+R 4x/8x/16x, MAXELL DVD-RW 4x, MAXELL DVD-R 8x/16x Discs that have been tested and are proven to be compatible with this recorder: VERBATIM DVD+RW 4x VERBATIM DVD+R 8x VERBATIM DVD-RW x VERBATIM DVD-R 8x JVC DVD-RW 4x MAXELL DVD-R 16x

Connections

DVD Recorder with Video Cassette Recorder

MWR20V6

OPEN/CLOSE

POWER ON

Getting started Recording
STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD IR CHANNEL D.DUBBING VCR SOURCE DVD STOP PLAY RECORD S-VIDEO VIDEO L AUDIO R

Playing discs

INSTRUCCIONES EN ESPAOL INCLUIDAS

Supplied Accessory

Remote control (NB550UD) with two AAA batteries RF cable Audio/Video cables Owners Manual (WPZ0901TM00) (WPZ010TM015 (1VMN13) or WPZ010LTE01)

Owner's Manual

Quick Guide (1VMN14) Editing Changing the Setup menu
Please read before using this equipment. If you need additional operating assistance after reading this owners manual or to order replacement accessories, please call or visit our web site at http://www.funai-corp.com
Before you use this unit , you need to complete connections. Refer to Connections on pages 14-16. To record a program easily, refer to Easy DVD recording on pages 17-18 after connections are completed. (You CANNOT record on any copyright protected DVD disc with this unit.)
Connect this unit directly to the TV. If the A/V cables are connected to a VCR, pictures may be distorted due to the copy protection system.
TOLL FREE : 1-800-605-8453
VCR functions Others Espaol

E9A80UD_MWR0V6_01.indd 1

006/01/18 11:45:1

Precautions

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Laser Safety

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM. LOCATION:INSIDE, NEAR THE DECK MECHANISM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modi-
fications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: OUR VITER LES CHOC LECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA P FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND.

A NOTE ABOUT RECYCLING

This products packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Make your contribution to the environment!!!
Used up batteries do not belong in the dust bin. You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.
For Customer Use: Read carefully the information located at the back of this unit and enter below the Model No. and Serial No. Retain this information for future reference. Model No. _____________________ Serial No. _____________________

E9A80UD_MWR0V6_01.indd

Precautions (contd)

IMPORTANT SAFEGUARDS

1.Read Instructions - All the safety and operating instructions should be read before the appliance is operated. 2.Retain Instructions- The safety and operating instructions should be retained for future reference. 3.Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow Instructions - All operating and use instructions should be followed. 5.Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. 6.Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7.Water and Moisture- Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8.Accessories - Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9.Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power Sources - This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 11. Grounding or Polarization - This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA No. 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

Editing

Available to DVD+R DL discs
Quick search for what you want to watch:

DVD-RW

You can easily find the part you want to watch using the search function. Search for a desired point on a disc by title, chapter or time.

Virtual Surround System:

You can enjoy stereophonic space through your exciting 2 channel stereo system.
Playing back on MP3 disc:
Available to DVD-RW discs formatted with DVD+VR mode +VR Available to DVD-R discs formatted DVD-R with DVD+VR mode Video Available to DVD-RW discs DVD-RW (Video mode, Finalized) Video Available to DVD-R discs DVD-R (Video mode, Finalized)

Changing the Setup menu

You can enjoy MP3 files which are recorded on CD-RW/R. VCR mode

CD MP3

Video CD
Available to Audio CDs Available to CD-RW/R discs with MP3 files Available to Video CDs Available to VHS tapes Use only tapes marked with this unit. Indicates that you need to select the DVD DVD mode by pressing [DVD] on the remote control before proceeding next step.

VCR functions

You can easily find the part you want to watch using the Index search/Time search functions. An index mark will be assigned at the beginning of each recordings you make. For Time search function, you can go to a specific point on a videotape by entering the exact amount of time you wish to skip.

Editing Deleting titles:

First: (Press:) First: (Press:)

Others Espaol

You can delete titles which you do not need anymore.

Putting names on titles:

You can put your favorite names on titles.
Setting / Clearing chapter marks:
Indicates that you need to select the VCR mode by pressing [VCR] on the remote control before proceeding next step.
You can set/clear chapter marks on titles.

E9A80UD_MWR0V6_01.indd 7

Functional overview

Front Panel

(*) The unit can also be turned on by pressing these buttons.

DVD/VCR ANTENNA IN OUT

Connection B
Note to the Cable TV System Installer :
This reminder is provided to call the Cable TV system installers attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding - in particular, specifying that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.
E9A80UD_MWR0V6_01.indd 15
Connection to an Audio System
When you change the connections, all devices should be turned off. Refer to the operation manual accompanying external devices for more information.
Method 1 AUDIO Stereo system Method 2 Dolby Digital decoder, MD deck or DAT deck

Analog audio input jacks

Digital audio input jack
Audio Coaxial Digital cable (commercially available)

DIGITAL AUDIO OUT

Setting Setup>Playback>Disc Audio>Digital Out> Connection PCM Dolby Digital If output is Dolby Digital encoded audio, connect to a STREAM Dolby Digital decoder. Unless connected to a Dolby PCM Digital decoder. Connecting to an MD deck or DAT deck.
* To complete these settings, refer to pages 69-70.
Playing back a DVD using incorrect settings may generate noise distortion and may also damage the speakers.
By connecting this unit to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital Multichannel surround sound as heard in the movie theaters. The audio source on a disc in a Dolby Digital Multichannel surround format cannot be recorded as digital sound by an MD or DAT deck. Playing back a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

006/01/18 11:45:4

E9A80UD_MWR0V6_01.indd 16

Easy DVD recording

The following will help you to understand easily how to record to DVD discs. Note: Make sure batteries are in the remote control and you have connected this unit and the TV correctly.
Step 1: Choose a disc type.
There are several types of recordable DVD discs to choose from. This unit can record on the following type of discs.
Step 2: Turn on the unit.

RETURN DISPLAY

For example, when you want to record repeatedly on the same disc, select the rewritable DVD+RW/DVD-RW type disc. When you want to save recordings without any alteration, a non-rewritable DVD+R/DVD-R can be your choice.

2 [K / L], select Channel. Using
Press [OK]. Channel menu will appear.
Getting channels automatically
3 [K / L], select Auto Using
Channel Preset. Press [OK]. The unit will start getting channels available in your area. Wait for several minutes to finish channel scanning.

1 [SETUP]. Press

Setup Required Settings Playback Display Recording Clock Channel Disc Edit

4 [SETUP] to exit. Press

You can select only the channels memorized in this unit by using [CHANNEL L / K] on the front panel or [CHANNEL - / +].
E9A80UD_MWR0V6_01.indd 19

006/01/18 11:45:8

Channel setting (contd)
You can select a channel by directly entering channel using the Number buttons on the remote control. Notes for using the Number buttons: When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (For example: 117, press [1], [1], [7]) You must precede single-digit channel numbers with a zero (For example: 02, 03, 04 and so on). You can select the line input mode (E1 or E2). To select E1 by pressing [0], [0], [1]. To select E2 by pressing [0], [0], [2]. Details are on pages 35-36.

To select a channel

You cannot change the channel when one of the components of the unit (VCR or DVD) is in the recording, OTR or Timer Recording mode. If the auto presetting is cancelled during presetting, some of the channels not yet preset may not be received. The selection will depend on how you receive the TV channels. Press [RETURN] or [SETUP] to cancel the auto presetting during scanning.

Adding/deleting channels

The channels you no longer receive or seldom watch can be deleted from the memory. You also may add channels into memory.
Select the channel number to add or delete. Press [{] or [CHANNEL -] to move to a lower channel number. Press [B] or [CHANNEL +] to move to a higher channel number. Press the Number buttons to select a channel number directly.

PQRS TUV WXYZ

DISC MENU

1. 2. 3.

-------------

4. 5. 6.

Using---[K / L], select a program 7. 8. --number. Press [OK]. Using [K / L], enter the Date. Press [B].
To record on a videotape, select 5. --6. --VCR. 7. -- To record on a disc, select DVD. 8. ---
Using [K / L], select a recording mode.
1. JAN/01 2. 3. 4. 5. -------

E1 DVD

--When pressing [L] at the 6. --current date, the Date will 7. --8. --change as follows.
Refer --- Recording mode on to 5. 6. --page 25 for DVD or page 74 for 7. VCR. --8. --When Auto (DVD only) is selected as a recording mode, the unit determines how much time is available on the disc and record in the appropriate recording mode to complete recording the program.

e.g. January 1st

JAN/01 Daily MON-SAT MON-FRI SAT FRI SUN JAN/31
1. JAN/01 12:57AM 2. 3. 4. 5. 6. -----------

DVD Auto

Using [K / L], enter the Start and End time. Press [B].
1. JAN/01 2. 3. 4. 5. 6. 8. ---------------

12:57AM

7. Press---[OK] when information is 8. --entered. Your program setting will be stored. To set another program, repeat steps 2 to 8. To exit, press [TIMER] or [SETUP]. When programs are overlapped, Overlap and the overlapped program numbers will appear on the TV screen.
If you have not set the clock yet: A manual clock setting menu will appear instead of the Timer Programming list at step 1. Continue with step 3 in Manual Clock Setting on page 23 before setting a timer programming. Press [{ / B] to move the cursor to the left and the right in the timer programming list. After step 9, you can use the other component (VCR or DVD) which is not currently programmed by turning the power on. Note that the programmed device will start to capture the selected channel 2 minutes before the start time and at the moment, if the other device still stays in recording, recording pause or OTR mode turning a different channel, the current mode will be canceled and you cannot change the channel. When both devices capture the same channel, the current mode continues to function.

006/01/18 11:45:37

E9A80UD_MWR0V6_01.indd 30

Timer Recording (contd)

Checking, canceling, or correcting the timer programming information
Press [TIMER SET]. disappears from the front panel display.
1. JAN/01 12:57AM 2. 3. 4. -------------
To clear the timer programming: Using [K / L], select your desired program. Press [CLEAR/ C-RESET]. To correct the timer programming: Using [K / L], select your desired program. Press [OK]. Next, correct the timer programming by using [K / L / { / B]. Finally, press [OK] again.

During playback, press [CM SKIP]. Normal play will start at 30 seconds ahead from the point you press [CM SKIP]. Every time you press [CM SKIP], the searching point will be extended by 30 seconds ahead. You can press up to 6 times (180 seconds). e.g. Press [CM SKIP] once.

CM Skip 30 sec.

(forwarding 30 seconds)
Playback will restart automatically.
E9A80UD_MWR20V6_02.indd 45

2006/01/17 17:58:07

Special playback (contd)

Rapid play

Rapid play function is available only during playback. Available only on discs recorded in the Dolby Digital format, Rapid play plays back in a slightly faster/slower speed while keeping the sound quality just as normal playback.
: Press [RAPID PLAY] once during playback. Plays back approximately at 0.8 times of normal playback. : Press [RAPID PLAY] twice during playback. Plays back approximately at 1.3 times of normal playback. : Press [RAPID PLAY] three times to play back in normal speed. No effects.
During playback, press [RAPID PLAY].

Step by step playback

Press [PLAY B] to continue the normal playback.
Audio (language) setting cannot be changed while using this mode. This feature may not work at some point in a disc. Audio is PCM during Rapid play mode.
STANDBY-ON VIDEO/TV VCR DVD OPEN/CLOSE.@/: ABC DEF
To play step by step backward: Press [SKIP H] repeatedly. Every time you press the button, the play will go backward by one frame. Press and hold [SKIP H / G] to reverse/ advance continuously.
DISC MENU SETUP STANDBY-ON

ABC CHANNEL JKL

SEARCH RETURN
TIMER VCR REC DVD REC REC MODE PQRS TUV WXYZ TIMER SET SLOW CM CLEAR/C-RESET SPACE SKIP RAPID PLAY TITLE
Press [SKIP G] repeatedly. The play will advance one frame (or step) at a time when you press [SKIP G] with the sound muted.
Only step by step forward playback is available for OK playing back Video CDs.
Slow forward / Slow reverse play
During playback, press [PAUSE F]. Then press [F.FWD D] or [REW E]. Every time you press [F.FWD D] or [REW E], approximate speed will be changed as follows. (The sound will remain muted.)
To return to the normal play, press [PLAY B].
Forward/reverse speed will be indicated with icons as follows. Forward (Approx. Speed) x1/16: x1/8: x1/3: Reverse (Approx. Speed) x1/16: x1/8: x1/4: Only slow forward playback is available for playing back Video CDs.
E9A80UD_MWR20V6_02.indd 46

2006/01/17 17:58:08

During playback, press [DISPLAY]. Display menu will appear.

0:00:00 DVD-Video

Using [K / L], select a desired zoom factor to zoom. Press [OK]. The zoom area will be displayed.
Using [{ / B], select [OK]. Zoom menu will appear.

Angle icon appears when a switching camera angle is available.
Angle icon does not appear on the screen in a case you have selected Angle as OFF in the Display setting. Refer to pages 68-69.

Reducing block noise

Using [K / L], select a desired option. Press [OK]. Your setting will be activated. This function reduces noise in the playback picture. When playing back discs recorded in long time mode such as EP or SLP mode, select Type 1 or Type 2. (Type 2 is more effective.) When playing back discs with a few noises such as DVD-Video discs, select OFF.
Using [{ / B], select. Press [OK]. Noise Reduction menu will appear.
E9A80UD_MWR20V6_02.indd 53

2006/01/17 17:58:18

Information on disc editing

Guide to a title list

Title list allows you to check the titles recorded on the disc easily. You can choose a title to play from this list and easily edit the titles as you prefer. Press [TITLE].

Editing discs

You can edit discs for the following items. Be sure that once you edit titles, they will not remain as original. Deleting titles (Refer to page 55) Putting names on titles (Refer to page 56) Setting / Clearing chapter marks (Refer to pages 57-58) Hiding chapters (Refer to page 59) Setting pictures for thumbnails (Refer to page 60) Dividing a title (DVD+RW/DVD-RW only) (Refer to page 61) When selecting Edit on Pop-up menu of the title list and edit the title, the title list is displayed after writing the edited contents onto the disc. Press [STOP C] to exit the title list.
NOV/21/06 11:00AM CH12 SP NOV/21/06 0:20:44 Play Edit Overwrite
NOV/24/06 10:05AM CH10 EP NOV/24/06 0:20:11
Edit Title Delete Edit Title Name Chapter Mark Current Chapter Index Picture Title Dividing
Editing discs (Setup menu)
NOV/22/05 11:00AM CH12 EP 0:00:59
Putting name on disc (Refer to page 62) Setting or releasing disc protect (Refer to pages 63-64) Erasing disc (Refer to page 65) Making edits compatible (Refer to page 65)
1.Titles recorded on the disc can be selected to edit by pressing [OK] with the cursor on the title. Using [K / L], select Edit. Press [OK]. 2.The arrow icon, which means the title list includes a next or a previous page. Press [K / L] by following direction of the icon. You can also use [{ / B] to go to the next / previous page. 3.The portion bar, which indicates the position of the disc. 4.The menus in here for editing as you prefer. The available menus depend on the disc type and the format type. An item which is not available is grayed. 5.The details of the title, which can be changed to the title name you will edit. 6.Time status bar of the title Time status will be held even after exiting the edit mode, and you can resume playback from that point. 7.The selected title thumbnail from the title list 8.Playback status of the current title

Using [K / L], select Yes. Press [OK]. The selected chapter mark will be deleted. Press [RETURN] to exit. Data will be written onto the disc momentarily. This operation may take a while to be completed.
Remaining time of the disc may decrease when adding chapter marks or increase when clearing chapter marks depending on the recording time or edited contents.
To delete all chapter marks:
Follow steps 1 to 3 on page 55 to display the Edit menu. Using [K / L], select Chapter Mark. Press [OK]. Option window will appear as illustrated step 2 on page 57. Using [K / L], select Delete All. Press [OK]. Confirmation window will appear.
Chapter Mark - Delete All 3
Using [K / L], select Yes. Press [OK]. Final confirmation window will appear.

Are you sure? Yes No

Using [K / L], select Yes. Press [OK]. All chapter marks will be deleted. Press [RETURN] to exit. Data will be written onto the disc momentarily. This operation may take a while to be completed.

2006/01/17 17:58:22

E9A80UD_MWR20V6_02.indd 58

Hiding chapters

You can hide chapters from the title list. Hidden chapters are skipped during playback. DVD First:
After this operation is completed, press [RETURN] twice to exit. Data will be written onto the disc momentarily. This operation may take a while to be completed. If you want to return Visible, select the chapter to be shown. Then using [K / L],, select Visible at the step 4 on this page. Data will be written onto the disc momentarily. After that Title list is displayed.
Follow steps 1 to 3 on page 55 to display the Edit menu. Using [K / L]], select Current Chapter. Press [OK]. Option window will appear.

Current Chapter 6

Visible Hidden

Visible

Using [SKIP H / G], [PLAY B] and [PAUSE F], decide the chapter to be hidden. Using [K / L],, select Hidden. Press [OK]. Hidden is displayed in the middle of the preview screen on Current chapter window. Hidden is also displayed on the lower right corner of the preview screen on Edit menu option window other than Current chapter window.

Make Edit Compatible Yes No
If Make Edits Compatible is not selectable in Disc Edit menu, you do not need to perform Make Edits Compatible to play in other DVD players.
E9A80UD_MWR20V6_02.indd 65

Tour of the Setup menu

The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Setup 1.Language setting Pages 67-68 Items (highlight is the default) Disc Menu Language English French Spanish Audio Language Original English French OFF English French English Franais Espaol ON OFF OFF 5 minutes 10 minutes Auto Bright Dark PCM Contents Set the language for disc menu.
Set the language for audio.

Subtitle Language

Set the language for subtitle.
2.Display setting Pages 68-69

OSD Language

Set the language for OSD (On Screen Display). Set the display or undisplay of multiangle icon in a case the DVD in playback mode contains multi-angle scene. Set the time to work the screen saver on the screen. Set the brightness of the front panel display. Set whether the sound recorded in 96kHz will be down sampled in 48kHz. Set the type of sound signal which outputs from the digital audio output jack. Compressing the range of sound volume. Set to the progressive scan mode (set to ON) or to the interlace scan mode (set to OFF). Set the type of still image in pausing playback. Set the parental level of your DVD discs. Set and change the password. Set the Playback Control. (Video CD only)

Angle Icon

Screen Saver
FL Dimmer 3.Audio setting Pages 69-70 Digital Out
48kHz 96kHz Dolby Digital PCM Stream
Dynamic Range Control 4.Video setting Page 71 Progressive Scan Still Mode
ON OFF ON OFF Auto Field Frame All level 8 to 1 Enter the current four-digit password ON OFF
5.Parental setting Pages 72-73
Parental Lock (Change password)

6.PBC setting Page 73

PBC (Video CD only)
If you change the setting in the Setup menu, the information of contents stays on even when the power is switched off. An item which is not currently available is grayed in the Setup menus.

2006/01/17 17:58:28

E9A80UD_MWR20V6_02.indd 66

Language setting

Press [STOP C] if you are playing a disc.
Using [K / L], select Playback. Press [OK]. Playback menu will appear.
Using [K / L], select Language. Press [OK]. Language menu will appear.

VIDEO/TV VCR DVD STANDBY-ON
Press [SETUP]. Using [K / L], select CD Playback Mode. Press [OK]. CD Playback menu will appear.
CD Playback Mode Random Play Program Play PBC (Video CD only) ON
Using [K / L], select PBC (Video CD only). Press [OK].
PBC (Video CD only) ON OFF
Using [K / L], select ON or OFF. Press [OK]. Your setting will be activated.
When playing Video CDs with PBC function, some operations (e.g. select and track repeat) cannot be performed. Select PBC function OFF to perform those operations. PBC setting turns to ON when loading Video CDs with PBC function, thus, even after setting PBC to OFF and ejecting the Video CD then reloading the Video CD, this setting turns to ON automatically.
E9A80UD_MWR20V6_02.indd 73

2006/01/17 17:58:35

Playback xxxx

1 [STANDBY-ON Press

4 [PLAY B] to resume play. Press 5 [STOP C] to stop Press

playback.

] on the remote control or the front panel of the unit. When you are playing a videotape, turn the TV on and be sure to select the input to which the unit is connected. VCR Press:
6 [STOP C / EJECT A] on Press
the front panel of the unit to eject the videotape.
2 a prerecorded videotape. Insert
Press [PLAY B] to begin playback.

3 playback, press During

[PAUSE F]. Playback will pause and sound will be muted.
When a videotape without record tab is inserted, the unit will start playback automatically. Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press [CHANNEL L / K] on the front panel of the unit or [CHANNEL - / +] on the remote control.
Recording and One-touch Timer Recording
Before recording, make sure: The desired channel is selected by pressing the Number buttons or [CHANNEL - / +] on the remote control or [CHANNEL L / K] on the front panel of the unit. There is a videotape with a record tab in the unit. The desired recording mode is selected in SP (standard play) or SLP (super long play) mode by pressing [REC MODE] on the remote control. Recording mode:
Tape speed Type of tape SP mode SLP mode Recording/Playback Time T60 T120 T160 1hour 2hours 2-2/3hours 3hours 6hours 8hours

If you are still having trouble with this unit after checking Troubleshooting, write down the error code and the error description, and call our helpline mentioned on the front page to locate an Authorized Service Center.

RF output switch

You can watch the TV programs with the tuner of the unit. (Usually channel 3 or 4 of the TV is available for the RF converter setting.) Be sure to connect the unit to a TV using the RF cable. Refer to page 14.
Each time the RF output channel is changed, CH3 or CH4 will appear on the front panel display.
1 channel 3 on your TV. Select 2 [VIDEO/TV] on the remote Press
control. If noise appears, change the RF output channel of the unit to CH 4 by pressing [VIDEO/TV] for 3 seconds. The RF output channel will alternate between CH3 and CH4 as follows.

for more than 3 seconds9

PQRS TUV WXYZ SPACE TITLE

3 seconds

(RF on) CH4 OK
DISC MENU SETUP 3 seconds

(RF on) CH3

(RF on) CH4 CHANNEL
E9A80UD_MWR20V6_02.indd 80
Before you start Analog audio
An electrical signal that directly represents sound. In contrast, digital audio which can be an electrical signal, but is an indirect representation of sound. See also Digital audio.

Dolby Digital

Glossary xxxx

Regions code

Regions associate discs and players with particular areas of the world. This unit will only play back discs that have compatible region codes. You can find the region code of your unit by looking at the rear panel. Some discs are compatible with more than one region (or all regions).
The system developed by Dolby Laboratories to compress digital sound. It offers you sound of stereo(2ch) or multi-channel audio (up to 5.1ch).

Aspect ratio

The width of a TV screen relative to its height. Conventional TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high).

Finalize

To make recorded contents on DVD discs possible to be played back on DVD players. With this unit, it is possible to finalize DVD+R/DVD-RW/ DVD-R discs.

Sampling frequency

The rate which sound is measured by a specified interval to turn it into digital audio data. The numbers of sampling in one second defines as sampling frequency. The higher the rate, the better the sound quality is.
Just as a book is split up into several chapters, a title on a DVD disc is usually divided into chapters. See also Title.

MP3 (MPEG Audio Layer 3)

MP3 is a method of compressing files. You can copy MP3 files on CDRW/R discs from the computer and play back the files on this unit.

IMPORTANT:

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI CORP.
ATTENTION: FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR NOTICE. To locate your nearest AUTHORIZED SERVICE CENTER or for general service inquires, please contact us at:
FUNAI CORPORATION Customer Service
Tel :1-800-605-8453 http://www.funai-corp.com
19900 Van Ness Avenue, Torrance, CA 90501

Printed in China

E9A80UD_MWR20V6_02.indd 88

1VMN22213 / E9A80UD

VIDEO AUDIO IN
[Cable Box or Satellite Box]

Disc DVD-VIDEO

Connect Video cable (supplied) Connect RF cable (supplied)
Connect Audio cable (supplied) Connect
From Cable or Satellite Company Indoor or Outdoor Antenna
This unit is compatible to play the following discs.
Logo Disc DVD-R (VIDEO mode, Finalized) CD-DA (AUDIO CD) CD-RW (CD-DA FORMAT, MP3 files) CD-R (CD-DA FORMAT, MP3 files) Video CD Logo
From Cable Company (No Cable Box)
I You can use either A/V or RF cables to connect to TV for operation.

Watching on TV

Press [STANDBY-ON to turn the unit on. ]
Input Mode Names for Common TV Brands

Admiral Curtis Mathis

AUX LINE1, LINE2, 00, 90, 91, 92, 93 INPUT, TV/VCR, 00, 90, 91, 92, 93 INPUT, AUX VIDEO, VIDEO1, VIDEO2, VIDEO3 AUX 00 AUX CHANNEL
DVD+R Double Layer DVD-RW (VIDEO mode, Finalized)
TV/VIDEO INPUT, TV/VCR, 00, 90, 91, 92, 93 TV/VIDEO VIDEO 00 VIDEO1, VIDEO2, VIDEO3 TV/GAME 00

.@/: ABC DEF

The number inside the globe refers to region of the world. This unit can play DVDs that are labeled for ALL regions or for Region 1.
1.Switch the input selector on your TV6 to an PQRS TUV appropriate external input channel WXYZ 7 (usually near channel 0). 2.Press a button on theCLEAR/C-RESEToriginal TITLE TVs SPACE remote control (see the table below) to select0an external input RETURN DISPLAY channel until the DVD recorders picture appears.
Hitachi JVC Kenwood LXI-Series Magnavox

Recordable discs

This unit can record to the following disc types. IThis unit formats discs with DVD+VR mode. IDVD-R/DVD+R discs can only be recorded to once. DVD+RW/DVD-RW discs can be recorded to and erased many times. IWe strongly recommend for good recording quality: SONY DVD+RW 4x, MAXELL DVD+R 4x/8x/16x, SONY DVD+R 4x/8x/16x, TDK DVD+R 4x/8x/16x, MAXELL DVD-RW 4x, MAXELL DVD-R 8x/16x IDiscs that have been tested and are proven to be compatible with this recorder: VERBATIM DVD+RW 4x, VERBATIM DVD+R 8x VERBATIM DVD-RW 2x, VERBATIM DVD-R 8x, JVC DVD-RW 4x, MAXELL DVD-R 16x