ECHNICAL INFORMATION

Models No. Description LS1030N 255mm(10") Miter Saw

New Tool

Model LS1O3ON is improved version of the existing Model LS1030. This model is the is sister Version of Model LS1040 except for Bevel Cut function, which LS1030N is not equipped.

(18 3/4

")

Specifications

Voltage (V) 120 No Load Speed Arbor Diameter Blade Diameter Net Weight Power supply cord Miter angle (left and right) Current (A) 15.0 Cycle (Hz) 50/60 Continuous Rating (W) Input Output 4600rpm 15.88mm(5/8") 255mm(10")-260mm(10-1/4") 11kg(24.3 lbs) 2.5m(8.2ft) Cutting capacities (HxW) with saw blade 255mm 90. 5mm(3-9/16") x 95mm(3-3/4") 69mm(2-3/4") x l30mm(5-l/8") 90.5mm(3-9/16") x 67mm(2-5/8") 69mm(2-3/4.' ) x 9-wn(3-5/8") Max. Output(W) 2300

Standard equipment

Dust Bag Ass' y ----------------------------1 pc. Triangular Rule-----------------------------1 pc. Socket Wrench 13--------------------------1 pc. Switch Button (as spare) ------------------2 pcs. T. C. T. Saw Blade255---------------------1 pc. (U.S.A.) Cross-cut Saw Blade255 -----------------1 pc. (for Canada and Mexico)

Optional accessories

Vise Ass'y (Vertical Vise) Vise Ass'y (Horizontal Vise) Holder 255 Holder Set Set Plate Crown Molding Stopper Set T.C.T. Saw Blade
The standard equipment for the tools shown may differ form country to country.

532mm(21")

0m 53 m 0 (7/ ")
CONCEPTION AND MAIN APPLICATIONS

<#LS1030N>

Hndle for carrying More efficient chip/sawdust collection.More efficient collection LS1030N 87% LS1030 34%.less ejection toward operator

T.C.T. Saw Blade 255

Rigid arm Accurate cutting can be performed.
Very quiet Noise at no load LS1030N 85dB LS1030 92dB(=total nose of five LS1030's)

Clear scale of angle

Positive stops at turn base for angles (left or right) 0,15,22.5,30,45

Repair

Greasing Grease the MAKITA grease on the movable and sliding points shown below. Up/down swinging points for the blade case Blade case, Arm, Rod 16 Turning support point of turn base and sliding point Turn base, Center on the base, Slide plate Positioning point of turn base Base, Knock spring Link plate edge Turning points of safety cover Center cover, Center plate Disassembling/assembling of blade case and compression spring i) Lower the blade case(motor in the Compression spring body) at maximum and insert the Rod 16 pin(Jig) with 4-6.5 mm in dia. and 120 mm or more in length into the two Arm holes shown on the figure.(The driver instead of pin can be used.) The compression spring can be fixed while it is being shrunk. ii) Remove the screw for mounting the link plate to disconnect the rod 16, and the blade case can be removed from the arm.

Spring holder

Link plate Screw for mounting Link plate

Pin(Jig)

iii) Place the block with suitable size for housing between the pins(jigs) as shown on the figure, use the arbor to press the spring holder, pull out the two pins, and lift up the compression spring little by little to remove it. *Be sure to lift up the compression spring only after removing the both two pins. For assembling, proceed in the reverse order against disassembling.
Pressing (arbor) Spring holder

Block(Jig) Pin(Jig)

Disassembling/assembling of the link plate i) The link plate serves for opening/closing the safety cover and also serves as the upper limit stopper in swinging up/down the blade case. Therefore, before removing the link plate, the compression spring should be shrunk while referring to the [Disassembling/assembling of the blade case and compression spring]. ii) To remove the link plate from the blade case, remove the mounting screw at the blade case side. For assembling, proceed in the reverse order against disassembling. *Apply the adhesive on the mounting screws(both at arm side and blade case side) of the link plate in assembling. (Adhesive : Screw lock super 1342)
Assembling of the slide plate Assemble the slide plate according to the base shape as shown on the figure below.

Slide plate Base

Fastening of the hexagon bolt M8 for mounting the turn base Adjust the fastening degree of the hexagon bolt M8 on the center of the turn base so that the turn base can smoothly move without clearance.
Turn base Hexagon bolt M8

Circuit drawing

Switch Cab tire cord

Yellow Field

Orange color