PM-15S1 REFERENCE INTEGRATED AMPLIFIER
Inspired by the already legendary SC-7/MA-9 combination and derived from the top class PM-11S1 we are proud to present the new Marantz PM-15S1. Coupling impressive design with outstanding performance we feel our engineers have created a worthy successor to the PM-17SA. The amplifier is built according to the new Marantz premium design without any visible screws, a heavy double layer chassis and a slightly blue illuminated front. The 3-stage construction with full Current Feedback and with short, symmetrical signal paths, independent left and right heatsinks, and new HDAM-SA2s ensure dynamic sound and perfect stereo imaging. Best components, reduction of external noise and other improvements further extend the quality. Derived from the PM-11S1 we are using the electronic linear volume control WM8816 from Wolfson. The PM-15S1 reflects our engineers passion for pure music, designed with the true audiophile in mind.
New Marantz Reference Series Design 80 Watts/Ch Into 8 Ohms / 120 Watts/Ch Into 4 Ohms Hybrid Ring-Core Power Transformer with Choke Coil HDAM SA2 Output Circuitry High Accuracy Liner Control Volume Current Feedback Topology Phono Amp WBT high quality speaker terminals Noiseless LCD Display F.C.B.S (Floating Control Bus System) Multi-linked Control Double Layered Bottom Plate
FEATURES Number of Channels 2 Output Power/Channel (20Hz - 20kHz) @ 8 80W HDAM (HDAM SA2) Power Transformer Toroidal Discrete Amplifier Stage Individual Level Adjust Tone Control Phono Input (MM/MC) Source Direct Speaker A/B IN/OUTPUTS AUDIO 0/6 (Balanced/Unbalanced) Analog L&R In Main Channel Amp In Bridge Mono Mode (Bi-Ampmode) 2 (Pre Out/Rec Out) Analog L&R Out Headphone Out OTHERS Marantz Floating Control Bus D-Bus Remote (RC-5) In/Out External Control (RS232C) -/AC Outlets (Switched/Unswitched)
SPECIFICATIONS THD (20Hz - 20kHz, 8) Input Sensitivity/Impedance Frequency Response S/N Ratio
0.05% 240mV/20k 5Hz - 120kHz (+/- 3 dB) 90 dB (CD, Line)
GENERAL Platinum Color Aluminum Front Panel Aluminum Top RC-11S1PM Remote Control AC 120V 60Hz Power Requirements 380W Power Consumption 175/16" x 415/16" x 171/2" Dimensions W x H x D (Inches) 39.4 Weight (lbs.)
*All specifications, dimensions and weights are subject to change without notice. D&M Holdings, Marantz, Marantz America, Inc. or any of its subsidiaries will not assume any liability for errors in this spec sheet which may result in consequential errors being made by retail dealers, designers, custom installers, cabinet makers or end users, etc based upon information contained within this document. 05/06
2006 Marantz America, Inc. www.marantz.com

Fr att ventilera enheten, stll den inte i ett stll eller bokhylla och tnk p fljande. - Vidrr inte ytterhljets ovansida under pgende drift. - Blockera inte ppningarna i ytterhljet under pgende drift. - Stick inte in freml under enheten. - Blockera inte ventialtionshlen ovanp enheten. Placera inte ngonting nrmare n 1 meter ovnfr apparaten eller Nederlands enheten. Installeer het toestel niet in een rek of boekenkast waar de ventilatie - Se till det finns omkring 0,2 meter fri plats runt omkring enheten. mogelijk wordt gehinderd. Let tevens op de volgende punten: Dansk - Raak de bovenkant van het toestel niet aan als het in gebruik is. - Blokkeer de openingen van het toestel niet als het in gebruik is. Anbring ikke apparatet i et rack eller en boghylde, da dette kan bloke - Plaats geen onderwerpen onder het toestel. luftcirkulationen omkring apparatet, lagttag ligeledes flgende: - Blokkeer de ventilatie-openingen aan de bovenkant van het toestel niet. - Berr ikke oversiden af kabinettet under anvendelsen. Zorg dat er tenminste 1 meter vrije ruimte boven het toestel is. - Bloker ikke bningerne i kabinettet under anvendelsen. - Zorg dat er 0,2 meter vrije ruimte rond het toestel is. - Stik ikke genstande ind under apparatet. - Bloker ikke ventilationsbningerne ovenp apparatet. Espaol Anbring ikke noget nrmere end 1 m over apparatets overside. Para ventilar la unidad no la instale en una estanteria ni estante para - Srg for, at der er frit omrde p omkring 0,2 m omkring apparatet. libros, y tenge en cuenta lo siguiente:

FOREWORD

This section must be read before any connection is made to the mains supply. WARNINGS Do not expose the equipment to rain or moisture. Do not remove the cover from the equipment. Do not push anything inside the equipment through the ventilation holes. Do not handle the mains lead with wet hands.
Never place heavy objects on the equipment. If a foreign body or water does enter the equipment, contact your nearest dealer or service centre. Do not pull out the plug by pulling on the mains lead, hold the plug. It is advisable when leaving the house, or during a thunderstorm, to disconnect the equipment from the mains supply.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to comply with the household power and safety requirements that exist in your area. This product can be powered by 230 V AC only.
(Figure 1) CONNECTIONS OF TUNER Connect the output jacks of your stereo tuner to the LINE 1LINE 3 jacks of this unit. CONNECTION OF VCR OR DVD PLAYER Connection the audio output jacks of your VCR or DVD player to the LINE1LINE3 jacks of this unit. CONNECTION OF COMPACT DISC PLAYER Connect the output jacks of your CD player to the CD jacks of this unit. CONNECTION OF ANALOG TURNTABLE Connect the L (Left) output cord of the turntable to the L PHONO jack of this unit, and connect the R (Right) output cord to the R PHONO jack. Also be sure to connect the turntable's grounding wire to the GND jack of this unit. The GND jack does not have to be connected if the turntable is not provided with a grounding wire. CONNECTION OF CD RECORDER/TAPE DECK Connect the IN (line input) jacks of the CD recorder or the tape deck to the OUT jacks of this unit, and connect the OUT (line output) jacks of the CD recorder or the tape deck to the IN jacks of this unit. CONNECTION OF SPEAKER SYSTEMS This unit is equipped with a sets of SPEAKERS terminals. - The speakers in the speaker system should have an impedance between 4 and 16 ohms. If speakers with an impedance of less than 4 ohms are connected, the protection circuit may be activated during play. - Connect the Right channel speaker to the R terminals, and the Left channel speaker to the L terminals. - The output terminals have positive ( : Red) and negative ( : white) polarity, and each speakers also has the same polarity ( and ). When connecting the speaker, be sure to connect the terminals with the same polarity ( with , with ). CAUTION: When connecting two pairs of speaker systems simultaneously, the impedance of each speaker system should be no less than 8 ohm. Connecting a speaker system with a lower impedance than 8 ohm may activate the protection circuitry and make normal stereo reproduction impossible.

Connection of speaker cord
IMPORTANT: (For UK version only)
This apparatus is fitted with an approved moulded 13 Ampere plug. To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.

HOW TO CONNECT A PLUG

The wires in the mains lead are coloured in accordance with the following code: BLUENEUTRAL (N) BROWNLIVE (L) 1. The BLUE wire must be connected to the terminal which is marked with the letter N or coloured BLACK. 2. The BROWN wire must be connected to the terminal which is marked with the letter L or coloured RED. 3. Do not connect either wires to the earth terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead not simply over the two wires.

COPYRIGHT

Recording and playback of any material may require consent. For further information refer to the following: Copyright Act 1956 Dramatic and Musical Performers Act 1958 Performers Protection Acts 1963 and 1972 any subsequent statutory enactments and orders
Refer to the Figures on the page 83 at the rear of this user guide. The numbers on the diagrams correspond to those in the text. All references to the connections and controls that are printed in BOLD type are as they appear on the unit. PRECAUTIONS The following precautions should be taken when operating the equipment. GENERAL PRECAUTIONS When setting the equipment ensure that: the ventilation holes are not covered air is allowed to circulate freely around the equipment it is on a vibration free-surface it will not be exposed to interference from an external source it will not be exposed to excessive heat, cold, moisture or dust it will not be exposed to direct sunlight it will not be exposed to electrostatic discharges 1

Strip coating from extermity. Twist conductors. Speaker cord
Turn counterTurn clockwise Insert conducclockwise to to tighten. tors. loosen. When combined with a Marantz SM-17 (main amp), the PM17mk2main amp can be used as a BTL amp (monaural). It cannot be used as a BTL amp when combined with other products.

ABOUT THIS USER GUIDE

PORTUGUES

ITALINO

ESPANOL

FRANCAIS

CONNECTIONS
ENGLISH FRANCAIS DEUTSCH NEDERLANDS ESPAOL ITALINO PORTUGUS SVENSKA DANSK
Fugure 1 Tuner, etc DVD player, etc CD-R

VCR, etc

To output jacks (LINE OUTPUT)

L SEPARATE

SPEAKERS SPEAKERS IMPEDANCE L+R:4-8 OHMS BTL:8-16 OHMS R L
R PHONO GND 1 / TUNER 2 LINE 3 IN CD-R OUT IN OUT TAPE

R PRE OUT MAIN IN

R AC IN COUPLED BTL SERIAL NO.
OUT MM MC R PHONO L R CD L REMOTE CONTROL
To AC power outlet The initial setting for the SEPAR AT E / C O U P L E D s w i t c h i s COUPLED. Keep the switch at the COUPLED setting if you are connecting it as shown on this page. See next page for examples of how to connect and use the PRE OUT (pre-amp output) jack and MAIN IN (main amp input) jack.
To input jacks (LINE INPUT)

Tape deck

CD Player
- It is also possible to connect a BS tuner, LV player, TV or other component to LINE1-LINE3 jacks. - The audio input/output jacks of VCR or other component can be connected to CD-R and TAPE as their program sources. 2

Analog turntable

PRE OUT JACK AND MAIN IN JACK USAGE EXAMPLES
You can expand your audio system through appropriate setting of the SEPARATE/COUPLED switch and connection of the PRE OUT jack and MAIN IN jack. SEPARATE/COUPLED switch When this switch is set to COUPLED, the PRE OUT jack and MAIN IN jack are connected internally, allowing the PM-17mk2to be used as a pre-main amp. When the switch is set to SEPARATE, the PRE OUT jack and MAIN IN jack are internally disconnected, allowing the PM-17mk2to be used as a pre-amp or main amp. Usage example 1: Bi-amp connection combined with Marantz SM-17 (main amp)
SPEAKERS SPEAKERS IMPEDANCE L+R:4-8 OHMS BTL:8-16 OHMS
INPUT SELECTOR CD INTEGRATED AMPLIFIER PM-17 PHONO LINE VOLUME 20 15

LINE 2

LINE 3 TEMP

REC SELECTOR

TAPE PHONES

CD-R TAPE

LINE 1 LINE 2

SPEAKERS 2

TREBLE

BALANCE

0 (-dB) SOURCE DIRECT

LINE 3

-6 ON OFF

6+ LEFT RIGHT ON OFF

R COUPLED

L (BTL) ATT R

Set the switch to NORMAL.

RNORMAL BTL

Set the switch to 0 (dB).

0 -6 (dB)

R BTL OUT

POWER AMPLIFIER SM-17

SPEAKERS IMPEDANCE L+R:4-8 OHMS BTL:8-16 OHMS SPEAKERS
If you are using a speaker system that supports bi-wiring, you can combine the PM-17mk2 with the SM-17 for bi-amp operation that provides a higher quality of sound. In case of BTL connection with SM-17. Please refer to the user guide of SM-17.
Set the switch to SEPARATE.
LINE IN L OUT IN TAPE OUT L

Graphic equalizer

Usage example 2: Graphic equalizer connection
Set the switch to COUPLED.
NAMES OF CONTROLS AND INDICATORS

(Figure 2)

A GND (GROUND) terminal
Connect the grounding wire from the Analog turntable to this terminal.
When the INPUT SELECTOR is set to PHONO, the type of cartridge used on the turntable can be selected between MM (Moving Magnet) and MC (Moving Coil) using this switch. Set this switch according to the cartridge used on the turntable. MM (Moving Magnet) Set the switch to the out MC (Moving Coil) )position.

M AC IN jack

Connect to AC power outlet. This unit can be powered by 230V AC only.
set the switch to the in ( )position.
Selects the program source to be produced, from PHONO, CD, LINE 1, LINE 2, LINE 3,CD-R and TAPE.

C PHONO INPUT jacks

Connect the output jacks of the Analog turntable to these jacks. D CD PLAYER INPUT jacks Connect the output jacks of a Compact Disc player to these jacks.

w VOLUME control

Turn the knob to adjust the volume. Turning the knob clockwise ( ) to increase the volume. The volume up-down operations can also be controlled from the provided remote control unit.
E LINE 1 LINE 3 INPUT jacks
These are LINE 1 LINE 3 input jacks which can be used to connect the audio outputs of AV components such as TV multiplex/stereo audio turners, VCRs, and leaserdisc players.

e PHONES jack

This jack accepts the standard stereo phone plug of headphones.

F CD-R IN/OUT jack

r REC SELECTOR switch
Connect the line output jacks and line input jacks of CD recorder to these jacks.

G TAPE IN/OUT jacks

Connect the play (output) jacks and record (input) jacks of tape decks to these jacks.

t SPEAKERS switch

Press to switch the speaker systems ON (pressed-in position) and OFF (out position). Set the switch to OFF (out position) when you listen through headphones only.

Output jack for connection to extension power-amp, mixer or similar.

y IR SENSOR

The unit receives the infrared remote control signal through this window. Point the transmitter of the remote control unit toward this window to send correct remote control signals.

I MAIN IN jacks

Connect the pre output jacks of your pre-amp to these jacks at the SEPARATE position of the selection switch J.

u POWER switch

Press to turn power ON and press again to turn it OFF. Meter !1 lights up when the POWER is turned ON. The pointer LED of the INPUT SELECTOR switch q also lights when the power is ON and goes out when it is OFF.
J SEPARATE/COUPLED selection switch
The initial setting of the selection switch is COUPLED position. This unit is possible to use integrated-amp at the COUPLED position. Set according to the SEPARATED position, this unit is possible to use pre-amp or power-amp.
i Tone (BASS, TREBLE) controls
Turn the knobs to adjust the tone. Turning a knob controls the level of the corresponding frequency range. Turning each control toward + boosts the corresponding frequency range and toward attenuates it. TREBLE: Controls the tone of high frequencies. BASS: Controls the tone of low frequencies.
Connect your speaker system to these terminals.

K SPEAKER Terminals

H PRE OUTPUT terminal
Selects the COPY mode between CD recorder and TAPE deck, or the signal to be output to the OUT jacks of CD-R and TAPE.

q INPUT SELECTOR switch

B MM/MC SELECTOR switch
(REMOTE CONT. BUS) By connecting this unit with a MARANTZ component equipped with the remote control (D-BUS) jacks, both components can be remote controlled as a system. For details of the remote control function, read the owners manual of the connected component. The bus OUT terminal is used to send signals to another item of equipment. The bus IN terminal is used to receive signals from another item of equipment.
L REMOTE CONTROL BUS terminals
Turn to correct the left-right imbalance which may occur in stereo broadcast reception or otherwise change the output level of either the LEFT or RIGHT channel. Be careful of the position of this control because turning it fully clockwise or counterclockwise mutes the sound from the other channel.
When this switch is pressed in, the signals are transmitted by bypassing the BALANCE and tone (BASS and TREBLE) control circuitry so that they can be reproduce with a higher quality. (The BALANCE, BASS and TREBLE controls are defeated.)

!1 Warm-up meter

With any audio unit, the real sound quality cannot be obtained immediately after the power is turned on, and warming up is required to make the unit exhibit its full performance. As time passes after the power has been turned ON, the temperatures of different parts of the unit become constant and the electrolytic capacitors become active. This meter allows to check the warm-up condition of the unit. The meter needle starts to swing gradually in a little while after the power is turned ON and reaches about 2/3 of the meters full scale in about 30 minutes. Now the unit has almost been warmed up and can reproduce music with its original performance. The meter positions immediately after turning power on and at the end of warming up and the time taken for warming up are variable depending on the temperature, ventilation and other conditions of the listening room where the unit is located.

!0 SOURCE DIRECT switch

o BALANCE control

PLAYING PROGRAM SOURCE

RECORDING OF TAPE DECKS

CD LINE 1 LINE 2

0 (-dB) SOURCE DIRECT TAPE PHONES

COPY LINE 2

LINE 1
Caution for analog disk play - Reduce the volume to the minimum position before replacing the cartridge or placing the stylus on the disk. - Do not apply shock to the turntable during play. Otherwise the stylus may jump and damage the disk surface. - Avoid installing the turntable near a speaker, for this may cause howling and make it impossible to increase the listening volume. - Do not turn power of the turntable off while the stylus is placed on a disk. Playing a CD player 1. Set the INPUT SELECTOR switch q to CD. 2. Play the CD player. 3. Adjust the volume with the VOLUME control w. Playing a source connected to one of LINE 1 to LINE 3 The source component connected to any of the LINE 1 to LINE 3 input jacks on the rear panel can be played as described below. 1. Set the INPUT SELECTOR switch q to LINE 1, LINE 2 or LINE 3. 2. Play the component connected to the selected input. 3. Adjust the volume with the VOLUME control w. Playing a CD-R 1. Set the INPUT SELECTOR switch q to CD-R. 2. Play a pre-recorded disk on the CD recorder. 3. Adjust the volume with the VOLUME control w. Playing a TAPE 1. Set the INPUT SELECTOR switch q to TAPE. 2. Play a pre-recorded tape on the tape deck. 3. Adjust the volume with the VOLUME control w.
Recording of analog disk played on the analog turntable 1. Set the REC SELECTOR switch r to PHONO. 2. Play an analog disk on the turntable. 3. Operate the CD recorder or the tape deck to start recording. Recording of a source connected to one of LINE 1 to LINE 3 1. Set the REC SELECTOR switch e to LINE1,LINE2 or LINE3. 2. Play the source component connected to the selected input. 3. Operate the CD recorder or the tape deck to start recording. Copying a pre-recorded tape using the REC SELECTOR switch r Regardless of the program source selected with the INPUT SELECTOR switch q, when copying from a CD recorder to a TAPE deck, set the REC SELECTOR switch r to CD-R TAPE. - You can listen to another program source selected with the INPUT SELECTOR switch q while you are copying.
Recording of CD 1. Set the REC SELECTOR switch r to CD. 2. Play a CD on the CD player. 3. Operate the CD recorder or the tape deck to start recording.
Playing an analog disk 1. Set the INPUT SELECTOR switch q to PHONO. 2. Play the analog turntable. 3. Adjust the volume with the VOLUME control w.
Recording a CD-R and a tape A program source such as the analog turntable, tuner or CD player can be recorded onto CD-R or tape as described below.

REMOTE CONTROL OPERATION

(Remote control unit: RC-17mk2PM) 2

The RC-17mk2PM remote control unit can control MARANTZ audio/video components equipped with an infrared remote sensor as well as other MARANTZ components which are connected with the above components through the remote control bus. The following illustration shows the button layout of the RC-17mk2PM. Note that the functions of the RC-17mk2PM that can be remote controlled are only the volume up/down control and input selection operations.
Button functions when the CD-R button is pressed:

Button Play

Function Fast forward Fast backward Not used Stop

OPEN/CLOSE +

Open/close Not used Not used Skip forward to next track

REPEAT

RANDOM

LINE 1 / TUNER

REPEAT RANDOM VOL VOL
Random play Amplifier volume Up Amplifier volume Down
Button functions when the TAPE button is pressed: Button Function Play Fast forward

OPEN / CLOSE

VOLUME
Stop Open/close Deck A Deck B Skip forward to next music Skip backward to previous music
components *1 These buttons are used as the amplifiers input selector.
Not used. Not used. Amplifier volume Up Amplifier volume Down
x Group of buttons for controlling playback, etc.
These buttons are used to control the CD player, tape deck, etc.
c Group of numeric buttons
These buttons are used to enter figures for the tuner, CD player, etc.

Button

Function Play Fast forward Fast backward Not used
v Group of amplifier (PM-17mk2) control buttons 2 These buttons are used to control the listening volume.
*1 Pressing one of these buttons (CD, CD-R,TUNER, TAPE DECK, etc., except for PHONO and LINE3) change the functions of the buttons in groups x, c and v according to the selected source component. Please refer to the following tables entitled, which show how the button functions change.
Stop Open/close Disc Up (changer-equipped model only) Disc Down (changer-equipped model only) Skip forward to next track Skip backward to previous track

VOL VOL

Amplifier volume Up Amplifier volume Down

REPEAT RANDOM

Repeat Random play
Button functions when the CD button is pressed:

z Group of buttons for selecting the connected
Fast backward Play direction change
Skip backward to previous track Repeat
Button functions when the LINE1(TUNER) button is pressed: Button Function Not used. Frequency Up Frequency Down Not used. Not used. OPEN/CLOSE + Not used. Preset Up Preset Down Programme type Up Programme type Down Not used. Not used. Amplifier volume Up Amplifier volume Down
HOW TO USE THE REMOTE CONTROL UNIT

1. Remote control unit

The distance between the signal transmitter of the remote control unit (RC-17mk2PM) and the IR SENSOR of the integrated amplifier (PM-17mk2) should be less than about 5 meters. To ensure remote control, the remote control unit should be pointed accurately toward the IR SENSOR and there should be no obstacle between the remote control unit and the IR SENSOR. Remote controllable range Stereo integrated amplifier (PM-17mk2)

Approx.5m

Remote control unit (RC-17mk2PM) Button functions when the LINE2 button is pressed: Button Function VCR play VCR fast forward VCR fast backward Not used. OPEN/CLOSE + VCR stop VCR eject Channel/program Up Channel/program Down 2. Loading batteries The service life of the batteries used in the remote control unit is about 1 year under normal use. Remove the batteries when the remote control unit is not to be used for a long period of time. Replace batteries early whenever they seem to be weakened. (1) Remove the back cover.
(3) Slide close the battery cover until it clicks.
Improper use of batteries may cause the risk of fluid leakage or explosion. Be specially careful in the following points. 1. Insert the batteries with the correct and polarity as indicated inside the battery case. 2. Do not use a brand-new battery and used battery together. 3. Dry cell batteries may produce different voltages even when their shapes are the same. Do not use different types of batteries together. 4. Some batteries are rechargeable and some are not. Be sure to read the caution and instructions described on each battery. 5. Used batteries should be disposed of in compliance with the treatment method specified for your local area.

VCR double-speed forward VCR double-speed backward
(2) Insert batteries with correct and polarity.

TROUBLESHOOTING

In case of trouble with the unit, first check the following before calling for service. What seems to be a serious malfunction is often due to a simple operation mistake. If the trouble still persists after checking, please consult your dealer or nearest MARANTZ service agent. The amplifier does not work and the warm-up meter lamp does not light. 1. Check if the power cord is plugged properly into an AC power outlet. The warm-up meter lamp lights but the amplifier will not function. 1. Check the settings of the INPUT SELECTOR switch, VOLUME control and SPEAKERS switches. Sound is produced only from one of the speaker systems. 1. Check the setting of the BALANCE control. 2. Turn power of the set off and change the connections of the left and right speaker systems. If sound is still not output from the same speaker system, check its connection cord or the speaker system itself. Sound is not produced at all. 1. Check the settings of the INPUT SELECTOR switches. 2. Check that at least one of the SPEAKERS switches is pressed in. 3. Check that the speaker cords are connected properly. 4. Check that the connection cords with RCA pin plugs are connected properly. 5. Check the SEPARETE/COUPLED switch position on rear panel. Sound from the analog turntable is not output or very noisy (hum noise). 1. Check that the connection to the PHONO jacks is made properly. 2. Connect the grounding wire of the turntable to the GND terminal on the rear panel of the amplifier set. If it has al ready been connected, try removing it. 3. Check that the cartridge is attached properly to the tone arm. 4. Remove the power plug of the turntable from the power outlet and insert it again by inverting the relationship of the left and right blades with respect to the power outlet slots.
TECHNICAL SPECIFICATIONS (DIN) Rated power output (20Hz to 20 kHz, 2ch simultaneous drive).. 60 W x 2 (8 load) 80 W x 2 (6 load) 100 W x 2 (4 load) Total harmonic distortion (20Hz to 20 kHz, 2ch drive, 8 load).. 0.01 % Cross-modulation distortion (SMPTE)... 0.01 % Output bandwidth (8 load, 0.04 %).. 10 Hz to 50 kHz Frequency response (CD, SOURCE DIRECT).. 5Hz to 70kHz, +0 / 1 dB Damping factor (8 load, 20Hz to 10 kHz)... 100 Input sensitivity/Input impedance
PHONO (MC).... 230 V/100 PHONO (MM)....2.5 mV/22 k HIGH LEVEL....220 mV/22 k MAIN IN.....1.6 V/22 k Maximum allowable PHON input (1 kHz) MC.... 15 mV MM..... 150 mV RIAA deviation (20 Hz to 20 kHz)... 0.2 dB S/N (IHF A network, input shorted) PHONO (MC)..... 76 dB PHONO (MM)..... 90 dB HIGH LEVEL.... 112 dB Tone control BASS (100 Hz)..... 8 dB TREBLE (10 kHz).... 8 dB Supply voltage.... 230 V/AC, 50 Hz Dimensions Width.....458 mm Height..... 110 mm Depth.....429 mm Weight..... 16 kg Accessories Remote control unit (RC-17mk2PM).... x Dimensions Width.....44 mm Height.....239 mm Depth.....17.5 mm Weight (without batteries).... 189 g SUM-4 (AAA size) dry cell battery.... x 2 Design and specifications are subject to change without notice. 82

INPUT SELECTOR CD

VOLUME INTEGRATED AMPLIFIER PM-27 15

Figure 2

COUNTRY AUSTRALIA AUSTRIA BELGIUM BULGARIA CANADA CYPRUS CZECH REPUBLIC DENMARK DUBAI ESTONIA F.Y.R.O.M. FINLAND FRANCE GERMANY GREECE HEADQUARTERS EUROPE: HONG KONG HUNGARY ICELAND INDIA IRAN IRELAND ISRAEL ITALY JAPAN KOREA KUWAIT LATVIA LEBANON LITHUANIA MALAYSIA MALTA MAURITIUS NETHERLANDS NEW ZEALAND NORWAY OMAN POLAND PORTUGAL PROFESSIONAL EUROPE PROFESSIONAL U.S.A. QATAR REUNION ROMANIA RUSSIA SAUDI ARABIA SINGAPORE SLOVAKIA SLOVENIA SOUTH AFRICA SPAIN SWEDEN SWITZERLAND TAHITI TAIWAN THAILAND TURKEY U.K. U.S.A. YUGOSLAVIA EXPORT www.marantz.com
COMPANY Scan audio Pty. Ltd. Huber & Prohaska GmbH Van der Heyden Audio N.V. Ariescommerce GmbH Lenbrook Industries Limited Empire Hifi systems Ltd. Audio International Hi-Fi Klubben Denmark V.V.& SONS Audio International Baltic T.P. KODI Hi-Fi Klubi Finland Marantz France Marantz Deutschland Adamco S.A. Marantz Europe B.V. Marantz Asia Ltd. Infovox Ltd. Radiobudin HF Marantz India Home Co. Marantz Ireland Elmor Ltd. Marantz Italy Marantz Japan Inc. Mk Enterprises Ltd. alAlamiah Electronics Intl. Ace Ltd. AZ Electronics S.A., 1, A Accapella Ltd. Wo Kee Hong Electronics Sdn. Bhd. Doneo Co Ltd. SKR Electronics Ltd. Marantz Trading Scan audio Pty. Ltd. Hi-Fi Klubben Norway Mustafa & Jawad Trading CO. Philips Polska Sp. z o. o. Corel2 Marantz Professional Products Marantz Professional Products Almana & Partners W.W.L. Vision + Alltrom SRL Trade Company SV Ultimate Fidelity Forward Marketing (S) Pte. Ltd. Audio International Slovakia Bofex Coherent Imports (PTY) Ltd. Marantz Spain Hi-Fi Klubben A.B. Sound Company AG Covecolor Pai-Yuing Co. Ltd. MRZ Standard Co. Ltd. Penta Elektronic Marantz Hifi UK Ltd. Marantz America Inc. ITM Marantz Trading
ADDRESS 4 Station Street, Thornleigh NSW 2120, Australia Taborstrae 95 / Ladestrae 1, Gebude Hangartner, A-1200 Wien, Austria Brusselbaan 278, 9320 Erembodegem, Belgium Makedonia Blvd. 16, 1606 Sofia, Bulgaria 633 Granite Court, Pickering, Ontario P.O. Box 5604, Nicosia, Cyprus Fugnerova 1, 67801 Blansko, Czech Republic Aboulevarden 1, DK-8000 Arhus C., Denmark P.O. Box 105, Dubai, U.A.E. Lo Hu 12, EE0026 Tallin, Estonia ul.Cedomir Kantargiev 21a, Skopje, Former Yugoslavian Republic of Macedonija Uudenmaankatu 4-6, SF-00120 Helsinki, Finland A division of Marantz Europe B.V., P.O. Box 301, Suresnes Cedex, France Hakenbusch 3, 49078 Osnabrck, Germany 188, Hippocratous Street, 11471 Athens, Greece Building SFF-2, P.O. Box 80002, 5600 JB Eindhoven, The Netherlands Unit 1706, Metroplaza II, 223 Hing Fong Road, Kwai Fong, N.T., Kowloon, Hong Kong Terez Krt.31, 1067 Budapest, Hungary Skipholti 19, P.O. Box 424, 121 Reykjavik, Iceland c/o Philips India Ltd., Plot 80, Bhosari Industrial Estate Pune - 411026, India 5th floor no 878 Philips Building Enghelab ave, P.O. 11365/7844 Tehran, Iran Clonskeagh, Dublin 14, Ireland 52 Heh Beiyar Street, Kikar Hamedina, Tel Aviv, Israel Via Casati 23, 20052 Monza (Milano), Italy, Servizio Consumatori 1678-20026, Numero Verde 35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan 121-210, 2F Shinhan Bldg., 247-17 Seokyo-dong, Mapo-ku, Seoul, Korea P.O. Box 8196, Salmiah 22052, Kuwait 61, LacPlesa Str., Riga LV 1011, Latvia P.O. Box 11 2833, Beirut, Lebanon Ausros, Vartu G5, Pasazo Skg., 2001 Vilnius, Lithuania 102 Jalan SS 21/35, Damansara Utama, 47400 Petaling Jaya, Selangordarul Ehsan, Malaysia 78 The Strand, Sliema SLM07, Malta P.O. Box 685, Bell Village, Port Louis, Mauritius A division of Marantz Europe B.V., Building SFF-2, P.O. Box 80002, 5600 JB Eindhoven, The Netherlands 4 Station Street, Thornleigh NSW 2120, Australia Lillegrensen 7, N-0159 Oslo, Norway P.O. Box 1918, Ruwi, Oman Al. Jerozolimskie 195b, Warszawa, Poland Comrcio de Electrnica Lda., Av. Lus Bvar, No 85 A, 1050 Lisboa, Portugal Kingsbridge House, Padbury Oaks, 575-583 Bath Road, Longford, Middlesex UB7 0EH, U.K. Distributed by: Superscope Technologies Inc., 1000 Corporate Blvd. Ste.D, Aurora, Illino P.O. Box 49, Doha, Qatar 180 Rue du Marechal Leclerc, 97400 Saint Denis, Ile de la Reunion Soseaua Bucuresti, Ploiesti 10, Sector 1, Bucharest, Romania Bld. 2, 7 Montazhnaya Street, 107497 Moscow, Russia Sameria Comm. Center, Roadah Dist., P.O. Box 7760, Jeddah 21472, Saudi Arabia Wo Kee Hong Centre, 29 Leng Kee Road, Singapore 159099, Singapore Nam. SNP 10, 96001 Zvolem, Slovakia Smartinska 152, HALA V/3, 61000 Ljubljana, Slovenia P.O. Box 1614, Alberton, 1450, South Africa Martinez Villergas 2, Apartado 2065, Madrid 28027, Spain Tegnersgatan 21, S-Gotenborg, Sweden Postfach, 8010 Zrich, Switzerland Av. Prince Hinoi, Cours de l'union sacr, P.O. Box 2334, Papeete, Tahiti 6th No 148 Sung Kiang Road, Taipei 10429, Taiwan R.O.C. 746-750 Mahachai Road, Wangburapa, Bangkok 10200, Thailand Sanayi Ve Ticaret Ltd. Sti., Selvi Kokak, No. 4/1, Senlikkoy, 34810 Florya, Istanbul, Turkey Kingsbridge House, Padbury Oaks, 575-583 Bath Road, Longford, Middlesex UB7 0EH, U.K. 440 Medinah Road, Roselle, IL 60172, U.S.A. Ljutice Bogdana la, Belgrade, Yugoslavia A division of Marantz Europe B.V., Building SFF-2, P.O. Box 80002, 5600 JB Eindhoven, The Netherlands