MARMITEK 8 in 1 UNIVERSAL REMOTE CONTROL
Button description Beschreibung der Tasten Le clavier Beschrijving van de toetsen

ENGLISH

Introduction The Marmitek 8 in 1 remote control will control most video and audio equipment. It replaces up to seven remotes so you just need one remote to control all of your equipment. On top of that this remote can also control lights and appliances anywhere in your home when used with Marmitek X-10 Home Automation Modules. With the use of a Marmitek Powermid receiver, you even can control your equipment from any room in your house. In addition to all these unique features, it is an easy to use universal remote. It is pre-programmed in the factory for most brands and models of equipment. Simply entering the code for your equipment and your remote is ready to use. If you want to add more commands, the remote is capable of learning the IR commands of almost any infrared remote control. How to install the batteries 1. 2. Push the tab of the battery compartment on the back site of your remote, and lift the cover. Install four fresh AAA batteries, taking care to match the + and - marks in the battery compartment.
Setting up your Marmitek 8 in 1 remote Button Descriptions: [1] Indicator light (LED): The indicator light flashes when the remote is operating. [2] Power: Works in the same way as your original remote. Also used to switch all Marmitek X-10 Lamp Modules on. [3] Set-up: Used for entering code numbers matching your TV, VCR or other equipment. [4] Learn: Lets you learn IR commands from an existing remote, that might not be in the Marmitek 8 in 1 library. [5] Marmitek X-10 button: Lets you control Marmitek X-10 Home Automation Modules to operate lamps and appliances around your home. [6] TV, VCR, CBL, CD, AUX1, AUX2, SAT: Used to select the device to control. [7] SHIFT: Secondary functions for pre-programmed codes. You may have some functions on your original remote, which do not appear on the keypad of the Marmitek 8 in 1 remote. This does not mean that they are not available. You may access them via the SHIFT key. If you miss a function, press the shift button once, and find the function you need by pressing the buttons. In the Shift mode, the LED is on continuously. To end the Shift mode press the Shift key once more. The SHIFT key can also be used to learn another function under the same key. 2
0. 9: Used as your original remote and to enter device codes. [8] A B: Used for toggle functions (pre-programmed mode). [9] Ent (Enter): Used in conjunction with the numeric keys for direct channel tuning. In set-up mode used to confirm. [10] Info: Works in the same way as your original remote. [11] Channel: Works like your original remote. Also used to switch Marmitek X-10 Home Automation Modules on and off. [12] Mute: Works the same way as your original remote. Also used to switch all Marmitek X-10 Home Automation Modules off. [13] Volume: Works like your original remote. Also used to brighten and dim lamps connected to Marmitek X-10 Lamp Modules. [14] Teletext HOLD: Holds the current page. [15] L1, L2: Lets you learn additional keys from your original remote. [16] Teletext MIX: Mixes the text with the TV program on the background. [17] Play, FF, Stop, Rew, Pause: Works the same as on your original remote. Also function as fast text colour keys. [18] Teletext ON. [19] REC: Record button. Works the same as your original VCR remote. You must press the REC button twice to begin recording. [20] Teletext OFF. Clearing the memory (recommended on first set-up): 1. 2. 3. 4. Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button. Press and release the LEARN key twice. Press the SETUP key. The LED will turn off after a few seconds. All code entries and learned command entries are now cleared.
Setting up for TV, VCR, Cable, CD and Satellite Receiver

1. 2. 3. 4. 5. 6.

Turn on the device you wish to control (TV, VCR, satellite receiver, CD etc.). Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button. Press and release the mode button that matches the device you want to control (TV, VCR, CD, etc.). Enter the 3 digit code from the Library code tables. The LED turns off after the last digit entered. Point the remote at the device and press the POWER button. Your device should turn off. Turn your device on and press CHANNEL+. If the device responds, set-up is complete. If some buttons do not operate your equipment, try one of the other codes for your brand.

NOTES: For audio and CD use the CD button, for TV the TV button etc. If your TV, VCR, Satellite receiver does not respond, try the other codes for your brand. If it still doesnt respond, try the Code Search method. If the LED blinks rapidly when you enter the code, you may have entered an invalid code. Recheck the code in the code list and try again. Using an AUX button to control a second TV, VCR, SAT, CBL or CD/Audio component: 1. 2. 3. Turn on the equipment you want to control. Press and hold SETUP until the LED indicator lights steadily. Release Set-up button. Press either AUX button, then press and release the mode button that matches the equipment you want to control (TV, VCR, CBL , CD, SAT). The LED blinks once. Enter the 3 digit code from the Library Code Tables. The LED turns off after the last digit entered. Point the remote at your component and press the POWER button. Your component should turn off. Turn your component on and press CHANNEL+. If it responds, set-up is complete. Your AUX button is now equal to a TV, VCR, CBL, SAT or CD button, depending on what mode you chose at step 3.

4. 5. 6.

Searching for codes: When your device cannot be found in the code list, or your device doesnt respond to any of the codes you entered, you can try to find the code you need by using the searching for codes method: 1. 2. 3. Turn on the device you want to control. Press and hold SETUP until the LED indicator lights steadily. Release Set-up button. Press the mode button that matches the equipment you wish to control. The LED blinks once.
Press CHANNEL+ repeatedly until the device to be controlled changes channel. If you go past the code accidentally press REW [<<] to step back (for first step push button twice). Press and release the ENTER button to complete the set-up.
Note: You may have to press CHANNEL+ many times (50+). If the device does not have a Channel Up function, use the PLAY [>] button (VCR only) or the POWER button. Identifying codes found using the search procedure: 1. 2. 3. 4. Press and hold SETUP until the LED indicator lights steadily. Release the Set-up button. Press the mode button that matches the equipment you wish to identify. The LED blinks once. Press and release SETUP. The LED blinks once. To find the first digit, press each number button from 0 to 9 until the LED blinks. The number you pressed is the first digit of the code. Press each number button from 0 to 9 as above to find the second digit. Press each number to find the third digit. When the third digit has been found, the LED will go out. Write down the found code on the label of the battery compartment.

Learning Your Marmitek 8 in 1 remote has the codes for most TVs, VCRs etc. in its code library. However, if the code for your particular device is not found in the library, you can learn these codes from your existing remote. Or if you find a code from the tables in this manual that almost matches your device, but a few buttons are missing, you can learn just those buttons. Learning commands: 1. Point your existing remote at the Marmitek 8 in 1 remote (front to front) with a distance of about 5 centimetres between the remotes. Press and hold SETUP until the LED indicator lights steadily. Press the mode button that matches the equipment you wish to learn. The LED blinks once. Press and release the LEARN button. The LED blinks once. Press and release the button on the Marmitek 8 in 1 remote that you want to teach. The LED blinks once. (Press SHIFT first to learn a shifted function). Press the button on your existing remote that you want to learn. Hold the button until the LED on the Marmitek 8 in 1 remote blinks off shortly. Repeat steps 5 and 6 for each button you want to learn. When youre finished learning all the keys, press ENTER.

2. 3. 4. 5.

Clearing all stored learned commands under a mode: 1. 2. 3. 4. 5. Press and hold SETUP until the LED indicator light steadily. Release the SETUP button. Press the desired Mode button (TV, VCR, CBL, SAT, AUX, CD, etc.). Press and release the LEARN key. Press the SETUP key. The LED will turn off after a few seconds. All learned commands entries under that mode are now cleared.
Notes for learning your remote: Make sure you have fresh batteries in both remotes before learning. Take care not to move either remote while pressing the buttons. No functions may be stored under the Learn, Setup, TV, VCR, CBL, SAT, CD, AUX1, AUX2, X-10, Enter keys or directly under the Shift key. Experiment by learning 2 or 3 keys initially (to ensure compatibility) and then clear the stored learned commands before completely learning your original remotes keyboard. Its only possible to learn under a total of three modes (even if it is only one key per mode). If you attempt to learn under a fourth mode the LED will flash for three seconds to indicate an error. When the memory is full, the LED will flash for three seconds. It is not possible to learn any additional keys although you can still overwrite previous learned keys. Experiment with the distance between the remotes if you have a problem learning. Some remotes do not have their LED in the centre so you might need to experiment with the side-to-side position of the remotes relative to each other. Do not sit directly under an incandescent lamp or direct sunlight while teaching the Marmitek 8 in 1 remote. Use buttons L1 and L2 to learn codes for which the Marmitek 8 in 1 remote does not have a corresponding button. If you have problems learning keys, try clearing the memory and try learning them again. Controlling your home using Marmitek X-10 Home Automation Modules The Marmitek 8 in 1 remote allows you to control practically everything electrical in your home. Besides IR technology that lets you control all your TV, VCR, Cable and Satellite equipment it has X-10 RF technology that lets you control lamps and appliances anywhere in your home remotely. Here are just some of the things you can do with your Marmitek 8 in 1 remote using the Marmitek X-10 feature: 6

Turn lights off or on and dim then while watching TV Start the coffee from your bedroom when you wake up Turn on lights at night to scare away intruders if you hear a noise Turn on your electric blanket before the movie ends, so its nice and warm to go to bed
To control your lamps and appliances you need Marmitek X-10 Home Automation Modules, which just plug into the existing wall sockets. No extra wiring is needed. Ask your dealer for more information. Controlling Marmitek X-10 Modules You can control the Marmitek X-10 Modules as follows: 1. 2. Press and release the Marmitek X-10 button. Use the number buttons to enter the Unit Code number of the chosen Module (You do not need to enter 0 first for a single digit number). Press the appropriate button for the function you require (see below).
Marmitek X-10 functions: On: Off: Bright: Dim: All Lights On: All Units Off: CHANNEL + CHANNEL VOLUME + VOLUME Power Mute
Changing the X-10 House Code The Marmitek 8 in 1 remote defaults to House Code A, and in most cases you will not need to change this unless you are experiencing interference form a neighbouring X-10 system. 1. 2. 3. 4. Press and release the Marmitek X-10 button. Press and hold SETUP until the LED indicator lights steadily. Release the setup button. Use the number button to enter the number equivalent to the chosen House Code (1=A, 2=B,. 16=P). Press the ENTER button to confirm the House Code. The LED turns off.
Note: The Housecode you choose must match the Housecode on the Transceiver Module (TM12 or Marmitek Alarm Console) you are using it with. Controlling an IR Mini Controller (IR543) If you already own an IR Mini Controller, you will need to change the code in the remote to use it. The code for standard Marmitek X-10 Home Automation is 013. The code to control the IR mini Controller is 014. To change the code: 7

1. 2. 3.

Press and hold SETUP until the LED indicator lights steadily. Release the SETUP button. Press and release the X-10 button. Enter 014 to control an IR Mini Controller, 013 for standard Marmitek X-10 control. The LED turns off after the last digit entered.
Controlling your equipment from any place in your home Your remote is prepared to work together with the Marmitek Powermid receiver. With this receiver its possible to control audio and video equipment from another room or even outside the house, using your Marmitek 8 in 1 remote control. Just plug the receiver into the wall socket and place it in line of sight of your equipment. Ask your dealer for more information. Troubleshooting The remote wont control your A/V equipment, or does not work at all Use manual controls or the original remote control to confirm the equipment is working properly. Be sure you pressed the device key for the device you want to control. Try finding the code for your equipment using Searching for codes method. Check the polarity of the batteries. Replace the batteries.

Benefits

The voice dialler security kits are fully supervised systems that gives you the power to protect your home whether you are home or away. These kits are easily installed (no wires). If a window or door sensor or motion detector is activated, sirens of 95 dBs will sound and make your house physically uncomfortable for a burgular thus forcing him/her to leave as quickly as possible. A voice dialler system will immediately call a friend or neighbor, playing your pre-recorded message indicating that there is a problem at your residence. A listen-in feature allows the friend or neighbour to hear what is going on inside the home and take appropriate action. In total, the console can monitor up to 16 door/window sensors or motion detectors, 8 remote controls, and 16 lamp or appliance modules. Additionnal sirens can be plugged-in everywhere and anywhere in the house. In times of peace, the security console can also be used to control any light or appliance. For example, you can turn out a child's bedroom lamp, your television set or computer or you can set the console to make fresh, hot coffee in the morning before you even get out of bed. In protecting yourself, your home and your loved ones, the voice dialler security kit makes life easier and more secure. The voice dailler security kits are available in two packages, a seven piece MS7000 kit and a four piece MS4000 kit. The MS4000 kit consists of: - SC12 Voice dailler console- DS10 Door / Window sensor - MS10 Motion Detector - Keychain Remote MS7000 kit same as MS4000 plus: - Extra DS10 Door/Window sensor - Full System Remote SH624 - Lamp Module LM12

Technical data

Security - CE Mark - PTT approved dialer - 433.92 RF operating frequency. Other frequencies available on request. - 230V 50 Hz supply. 9 V PP3 back up battery - 20 hours stand-by time - Integral 95 dB siren - Monitors up to 16 sensors (door/window and/or motion detector) plus 8 remotes - Dimensions: L180-W128-H52 mm Keychain remote: KR10 (Arms and disarms the security system and has ON/OFF feature for lamps and/or appliance modules) - CE Mark - 2 years operating life using 2 x alkaline AAA batteries - Dimensions: L63-W40-D14 mm HandHeld remote: SH624 (Arms and disarms the security console and controls up to 4 light and appliance modules, including dimming control of incandescent lights. Panic and Silent Alarm.) - CE Mark - 1 year operating life using 4 x alkaline AAA batteries - Dimensions: L115-W72-D20 mm Door/window sensor: DS10 (Transmits wireless signals to the console when a door or window is opened) - CE Mark - 2 years operating life using 2 x alkaline AA batteries - Dimension: H83-W54-D22 mm Motion detector: MS10 (Protects areas that have more than one entry point. Wireless battery operated.) - CE Mark - Built in test function - Double knock sensitivity adjustment - 1year operating life using 4 x alkaline AA batteries - Dimensions: H120-W75-D42 mm console:

MARMITEK, Tel: +831,

Fax: +232, Email: Marmitek@Compuserve.Com

FEATURES

3 IN 1 REMOTE
UNIVERSAL INFRARED REMOTE CONTROL FOR TV AND VIDEO RECORDER AND SATELLITE RECEIVER PRE-PROGRAMMED FOR ALMOST EVERY BRAND AND MODEL REPLACES THREE EXISTING REMOTE CONTROLS REPLACEMENT FOR DEFECTIVE OR LOST REMOTES EASY TO SET UP WITH 3 DIGIT CODES CONVENINT AND EASY TO USE KEYBOARD COMPREHENSIVE OWNERS MANUAL IN 4 LANGUAGES (ENGLISH, FRENCH, GERMAN AND DUTCH) RED INDICATOR LIGHTS WHEN IR COMMANDS ARE TRANSMITTED
Description With this 3 in 1 Universal Remote Control (URC), almost every piece of video equipment (except B&O) can be controlled. This URC replaces three existing remote controls. Now only one remote is needed to control a TV, a video recorder and a satellite receiver. The 3 in 1 URC is pre-programmed at the factory for most brands and models. By pressing the Set Up key and entering 3 digit codes from the comprehensive brand list (included with the unit), the URC is ready for use with one TV, one satellite receiver and one Video recorder. The URC has function keys for TV, VCR and SAT mode. When pressing the TV key, the keyboard will be set to the chosen TV, pressing the VCR key will set the keyboard for the chosen video recorder while pressing the SAT key will set the keyboard for the chosen satellite receiver. The 3 in 1 URC has keys (Fast) Text and hidden functions for Color and Brightness (through the Shift key). Beside entering a channel number, the P+ and P- keys can be used to scan through channels (only when this function is available on the equipment).

TECHNICAL SPECIFICATIONS

Batteries: KEYS 2 x AAA
TELETEXT: On Off Red Yellow Green Blue Mix Info Hold VCR MODE: Power Program P+ Program P Shift, Set Up -/--, Enter Record Play Rewind Pause Fast Forward Stop SAT MODE: Power Program P+ Program PMute - / --, Enter Volume V+ Volume VShift / Set Up 0-9
TV MODE: Power * Program P+ (Brightness +) * Program P - (Brightness -) Mute * Volume V+ (Colour +) * Volume V - (Colour - ) Shift, Set Up -/--, Enter 0-9

through Shift key

Art. No.

980804

MARMITEK: Tel. +831, Fax: +E-mail: Marmitek@Compuserve.Com
UNIVERSAL PREPROGRAMMED REMOTE CONTROL FOR ALMOST ALL VIDEO EQUIPMENT AND MARMITEK X-10 HOME AUTOMATION MODULES PRE-PROGRAMMED FOR MOST ALMOST EVERY BRAND AND MODEL (EXCEPT B&O) REPLACES 6 EXISTING REMOTES CODE READOUT WORKS IN COMBINATION WITH THE IR 543 MINI CONTROLLER TO CONTROL LIGHTS AND APPLIANCES BACKLIT KEYS BIG BUTTONS FOR EASY USE EASY TO SET UP RED INDICATOR LIGHTS WHEN COMMANDS ARE TRANSMITTED
Description The Marmitek 6 in 1 Universal Remote Control (URC) will control most video equipment (except B&O). On top of that, this URC can also control lights and appliances anywhere in a home when used with a IR 543 IR Interface (optional). The 6 in 1 remote is capable of controlling TVs, Video recorders, Satellite receivers, Cable boxes and Marmitek X-10 Home Automation Modules. With the use of the units two AUX buttons, a second TV, Video recorder, etc. can be controlled. The 6 in 1 URC is capable to control up to ten (groups) Marmitek X-10 Modules, with keys for the ON, OFF, DIM, BRIGHT, ALL UNITS OFF and ALL LIGHTS ON commands. The House Code for the Marmitek X-10 system is easy to set up via the keypad. The remote is supplied with a comprehensive owners manual in four languages (English, French, German and Dutch). Simply enter the 3 digit code from the enclosed code list, and the URC is ready to use. The Remote features Back Lit and Auto Power Off. Secondary functions can be activated by use of the Shift key.

Supply voltage: Supply current : Making capacity: 230 V 10% 50 Hz 20 mA capacitive 500 W (incandescent lamps only) 1 A (motors) 10 A (resistive loads) according to EN 50081-1 according to EN 50082-1 according to EN 60950 and EN mVpp min 50 mVpp max at 120 kHz 180 (L - N) at 120 kHz - 10 C to + 50 C (operation) - 20 C to + 70 C (storage) 52 x 122 x 33 mm (width x height x depth without plug)
EMC emission: EMC immunity: Electrical safety: Signal sensitivity: Input impedance: Ambient temperature: Dimensions:
Wall-mounted switch (AW10)
230 VAC - 50 Hz - 10A LOAD RATING
Key Features w Replaces any normal switch for X-10 control of lighting (includingfluorescent lighting) or appliances such as heater/fans etc. rated up to 10 A. w Works with X-10 controller and momentary action wall switches including "designer" wall switches.
Can also be used like an ordinary switch.
Supply voltage: Power consumption: Supply current: Making capacity: EMC emission: EMC immunity: Electrical safety: Signal sensitivity: Input impedance: Connections: Ambient temperature: 230 V +10% -15% 50 Hz < 2,5 W 20 mA capacitive 2000 W (incandescent lamps only) 10 A (resistive load) according to EN 50081-1 according to EN 50082-1 according to EN 60950 and EN mVpp min. 50 mVpp max. at 120 kHz 180 (L - N) at 120 kHz screw type terminals for phase, neutral, switched phase, control 2. - 10 C to + 50 C (operation) - 20 C to + 70 C (storage)
The X-10 wall mounted light switch is a receiver module that is controled by any X-10 controler. It can be used like an ordinary switch. The wall-mounted light switch simply replaces the normal light switch and is mounted into a flush box. It can also be controlled by external momentary action switches connected to terminal 2. The AW10 responds to "standard" X-10 that is: "All units off" from any X-10 controller set to its house code regardless of unit code or alternatively individual unit control by "On" and "Off". The unit is currently supplied with 3 different cover plates: Busch Jaeger Duro 2000, Jung CD500 and Gira (the mounting frame is available from your nearest wholesaler). Check with X-10 for the latest available cover plate.

Options CK11 kit including: CM11 computerinterface 2 x Lampmodule LM12 Transceiver Module TM12 Appliance Module AM12 Remote HR10 ActiveHome software on CD-Rom Controls and Indicators Connections AC outlet on front of module for computer power cord. RJ11 socket at base of module for serial connections. Specifications AC supply: 220VAC/50 Hz X-10 Powerline: 120KHz/2.5vp-p Backup battery: 2 x AAA cell Backup time: 1 Week typ Events/macros stored*: 25 typ, 39 max *varies with mix of events & macros.
PowerHound Watchdog (DK10)
Watchdog System - Deters intruders before they break in
Key Features Automatically activates a high quality digital recording of a dog barking when the outdoor PIR senses movement from an approaching intruder. Automatically turns on a light a few seconds after barking starts (with Lamp Module) to increase realism. Automatically turns on one or more lights at dusk and turns them off again at dawn. Compatible with the full range of Marmitek X-10 home automation products including HR10 and RW10 Home Automation remotes. PIR also works with Marmitek X-10 transceivers and security systems. The FBI rates sound and light as the two best intruder deterrents. PowerHound is an innovative and yet attractively simple product that provides both - it barks when an intruder approaches and switches on lights a few seconds later, just as the owner would if he were there. It also turns lamps on at dusk and off at dawn while the owner is away. Conventional burglar alarm systems are very effective; but, they do have one drawback: the intruder has already forced the door or entered the home by the time the alarm is triggered. What is really needed is a system that can protect the home before the burglar breaks in - a first line of defence. The solution is man's best friend. Noone complains about the occasional barking of a dog from inside the house, but it is a highly effective deterrent when someone approaches the door, especially when lights turn on as 'the owner comes to investigate'. A weatherproof infrared motion detector discretely mounted above the front door detects an approaching person and sends a radio message to trigger the base unit. Additionally, at night, a light sensor built into the motion detector automatically triggers the base unit to turn on other lights in the home - a well proven intruder deterrent. You can even control the lights yourself using a Marmitek X-10 wireless remote. Using the PIR Motion Detector with other X-10 products. The Outdoor PIR Motion Detector can also be used with other Marmitek security systems or transceiver modules to turn lights on at dusk and when someone approaches. A powerful loudspeaker in the base unit plays back a high quality digital recording of a barking dog. In the next few seconds a light comes on in the hallway and the effect is complete - a convincing demonstration that this is one home that should well be left alone. Options Option 1 Option 2 Option 3

PIR only Dog + Keychain Dog + Keychain + PIR
Controls and Indicators Base Unit Push button on/off at back of unit. Rotary code wheel at back of unit to set X-10 House Code. Rotary volume control. PIR Motion Detector LED indicator lights when motion detected. Specifications Base Unit 220 VAC/50 Hz AC supply: Batteries: 9 x 'C' cells RF receiver frequency: 418 or 433 MHz X-10 Powerline: 120KHz/5 V pk-pk Approvals: CE Mark MPT1340 or ETS 300220 PIR Motion Detector Batteries: 4 x 'AA' cells RF frequency: 418 or 433 MHz Approvals: CE Mark MPT1340 or ETS300220
Outside PIR Motion Detector (DM10)
For external use - With built-in light sensor

Key Features

When the outdoor PIR senses movement from an approaching intruder, automatically activates a high quality digital recording dog barking from the PowerHound, and turns on an Marmitek X-10 module. Automatically turns on one or more lights at dusk and turns them off again at dawn when used with Marmitek X-10 transceivers or security systems. Compatible with the full range of Marmitek X-10 home automation products.
The Police Department rate sound and light as the number one intruder deterrent. The PIR motion detector is an innovative and yet attractively simple product that activates both - it signals when an intruder approaches causing an Marmitek X-10 transceiver to switch on lights and appliances just as the owner would if he was there. It also signals when it is dusk and dawn while the owner is away. Conventional burglar alarm systems are very effective, but they do have one drawback: the intruder has already forced the door or entered the home by the time the alarm is triggered. What is really needed is a system that can protect the home before the burglar breaks in - the first line of defence. A weatherproof infrared motion detector discretely mounted detects an approaching person and sends a radio message to an Marmitek X-10 transceiver - PowerHound, Security System or Homecontrol.
The outdoor PIR performs three separates functions: 1. When used with the dog console and set with the same House / Device code as that of the dog it initiates a barking sequence when it detects motion. 2. When used with a standard Marmitek X-10 transceiver or security product it turns on an Marmitek X-10 module when motion is detected. 3. It turns on a second module when dusk is sensed and turns off the same module when dawn is sensed. When used with any Marmitek X-10 transceiver, the customer should adjust the House code wheel in the battery compartment of the PIR to match the one on the transceiver. After setting the code wheels install 4 "AA" batteries as illustrated in the battery compartment. On initial power up the PIR will be inactive for sixty seconds to allow the amplifier time to stabilize. The PIR once stabilized will transmit Marmitek X-10 code every time it detects motion. However there is a minimum time between detections of thirty seconds i.e. after motion has been detected and RF transmitted the PIR becomes inactive for a period of thirty seconds. The unit

The connection diagram shows how to install the DIN 63 A FD 10 filter coupler correctly: behind the residual current circuit breaker, yet in front of the fuses for separate circuits. The filter is mounted by simply snapping it onto the DIN rail (see figure) and has the following screw-type terminals: - L (below) for the phase input (from residual current breaker) - N for neutral - L (above) for the phase output (to the fuses/separate circuits). Use additional Marmitek X-10 filters (up to three) for installations with more than one phase. Couple the filters by connecting their terminals K to the next phase, respectively (see figure). For connecting, use a wire of 1mm cross section.
Public m ains pow er netw ork
L1 L2 L3 N M a s te r fu s e s 63 A m ete r resid ua l c urren t circu it brea k er

M ains distribution box

F D filter / p ha se c ou pler fus e c irc uits L1 kW h N N N

X- 10 signal

L 1 s tov e o v en
L 2 la undry L 3 b as e m e nt

Installation Diagram

2.4GHz transmitter and receiver set for high quality wireless transmission of video and audio signals Stereo audio with high dynamic range Video and audio inputs via SCART or RCA Video and audio outputs via SCART, RCA or channel 36 RF (PAL B/G) via a built-in modulator with IEC coax connector Video transmitter has a built-in RF receiver for Marmitek wireless remotes Model 130 includes a wireless IR/RF 8 in 1 Preprogrammed & Learning Universal Remote Control for controlling video and audio sources (e.g. video recorder or satellite receiver) connected to the transmitter side. Up to 4 channels available for combining multiple transmitters. Multiple receivers can be combined with up to 4 transmitters. Audio (mono or stereo) only transmission possible.

GIGAVIDEO VIDEO SENDERS

APPLICATION INFORMATION Connecting a second TV without pulling extra cable by using model 130. The transmitter will be connected to a video source like video recorder and/or satellite receiver. By means of the universal remote control supplied with model 130, the video source now can be remotely controlled. Any channel can now be selected or video controlled from the receiver side. Wireless surveillance of camera's for security, baby or patient care. Model 120 is most suitable for this application. When the camera also provides audio signals both audio and video can be transmitted. A useful tool for (in store) presentations. By combining one transmitter with multiple receivers, making presentations can be simplified by using a number of monitors. When used in combination with a VGA to CVBS converter (not supplied), PC monitor screens can be transmitter to e.g. TV's or other monitors.

TECHNICAL SPECIFICATION Wireless transmission: Frequency: Channels: Range: Sender inputs: Video: Audio L + R: Receiver outputs: Video: Audio L + R: RF output: Dimensions: Remote Control:

Receiver

TV / Monitor
Gigavideo 130 Part. No. 08966 Transmitter, Receiver and 8/1 universal remote control
2,4 GHz meters open air, 10-35 meters in house 1 Vpp, 75 Ohm 1 Vpp, 600 Ohm

Video, L+R

Gigavideo 120 Part. No. 08965 Transmitter and Receiver

Coaxial (CH 36)

1 Vpp, 75 Ohm 1 Vpp, 600 Ohm A/V modulated CH 36

Transmitter

Gigavideo 110 Part. No. 08976 Separate Transmitter for 120 and 130 sets

Power: Accessories:

160 x 215 x 88 Built-in 433,92 MHz receiver in transmitter. Equipment controlled via external LED 230 VAC - 50 Hz AV RCA leads + SCART adapters, IR LED with 1,5m lead
Video, Sat. tuner CAI, Aerial, Dish
Gigavideo 100 Part. No. 08983 Separate Receiver for 120 and 130 sets
IR LED * When available, use either SCART/AV or Coax input on TV SCART/AV gives highest picture quality)

Part. No.

GV 130: 08966 GV 120: 08965 GV 110: 08967 GV 100: 08983

980201

Remote controller (HR10)
16 channel RF remote controller
Key Features w Lets you control up to sixteen X-10 modules. w Sends wireless RF signals to the transceiver module TM12 or to any X-10 wireless security system w Compatible with the full range of X-10 home automation products.
The HR10 lets you control up to sixteen X-10 modules (lights and appliances) remotely from anywhere inside or outside your home even from your car as you enter your driveway. You can turn on and off, bright and dim any X-10 module set to same house code than the HR10. A slide switch allows you to control module set to house code 1 thru 8 and 9 thru 16. The wireless remote control HR 10 is normally used with the TM12 transceiver which passes through all codes from the wireless wall switches onto the powerline to control X-10 modules. You can also use the wireless remote control HR10 with any X-10 security system instead of the TM12.
Batteries: RF frequency: Radiated output: RF operating range: Approvals: Ambient temperature: 4 x AAA 418 or 433;92 MHz < 5833 V/m @ 3m 30 m (open field) MPT1340 or ETS 300220 CE Mark - 10 C to + 50 C (operation) - 20 C to + 70 C (storage)
Typical application Control lights or appliances from anywhere inside or outside your house - in the yard or from your car. Attach the wireless remote control to the wall inside a doorway (using Velcro) so you can turn on lights as you enter the room. Keep one by the bedside so you can turn on lights if you hear a strange noise in the middle of the night. Add additional wireless remote controls, leave one in your house and have one in your car. A disabled personcould use the wireless remote control from a weelchair. The severely disabled could use a mouthstickto operate the buttons on the wireless remote controlwhich could be easily mounted on the wheelchair's armrest

Supply voltage: Supply current : Making capacity: Regulating time: EMC emission: EMC immunity: Electrical safety: Signal sensitivity: Input impedance: Fuse: Connections: Ambient temperature: 230 V +10% -15% 50 Hz 20 mA capacitive 60 to 700 W (incandescent lamps only) 3,5 sec +/- 0,2sec from fully on to off according to EN 50081-1 according to EN 50082-1 according to EN 60950 and EN mVpp min 50 mVpp max at 120 kHz 60 (L - N) at 120 kHz 2,5 A (T) screw type terminals for phase, neutral, switched phase, control 2. - 10 C to + 50 C (operation) - 20 C to + 70 C (storage)

La m p or T rans form er

M om en tary
- Mount dimmer by snapping it onto the DIN rail. - Connect phase (L) and neutral (N) to the corresponding terminal at the bottom of the dimmer.

A M I E

- Connect load cable (light) to terminal L at the top of the dimmer. - Connect the cable coming from the pushbutton wall switches (switched phase) to terminal at the top of the dimmer.
Now, check the correct operation of the dimmer: - Switch on appropriate mains fuse and master switch. - Press one of the connected wall switches briefly. The lighting is switched on. - Press the same or another push-button briefly once again. The lighting is switched off. - Now press and hold one of the connected push buttons for sometime: the lighting is switched on and then dimmed darker and darker. When the push-button is released, the brightness of the light stays constant. - When the push-button is pressed for a very long time, the lighting is dimmed down to OFF: then it picks up gradually in brightness again until maximum, and the cycle starts over. - Finally, set the rotary code switches on the front side to the desired device address (e.g. C5) with a screwdriver and note this address down in a list. - The AD10 DIN rail dimmer includes the MEMORY DIM feature which allows the unit to DIM or BRIGHTEN directly to the next Marmitek X-10 initiated light level. NOTE: When using the DIN dimmer with low voltage lights, install the transformer as if it was the lamp as indicated in the wiring diagram. As with the other receiver modules, the device address can be changed easily at any time without disconnecting any cables.
Dimmer plug-in module (LM12)
230 VAC - 50 Hz - 300W LOAD RATING
Key Features w On/Off and dimmer control of incandescent lighting. w Available in a wide range of plug style (British, German, French, Italian, Euro-style, Swiss, Australian/Newzealand, Danish, etc.). w Designed to operate with 230VAC 60 W to 300W incandescent lamps.

Supply voltage: Supply current : Making capacity: Regulating time: EMC emission: EMC immunity: Electrical safety: Signal sensitivity: Input impedance: Fuse: Connections: Ambient temperature: 230 V +10% -15% 50 Hz 20 mA capacitive 60 to 500 W (incandescent lamps only) 3,7 sec 0,2sec from fully on to off according to EN 50081-1 according to EN 50082-1 according to EN 60950 and EN mVpp min 50 mVpp max at120 kHz 60 (L - N) at 120 kHz 2,5 A (F) screw type terminals for phase, neutral, switched phase. - 10 C to + 50 C (operation) - 20 C to + 70 C (storage)
Typical applications This unit is used for scene lighting, typically in living rooms, dining rooms and study/reading rooms. The ideal light level can be pre-programmed in your controller or Marmitek CM11.
Switch off appropriate mains fuse !
- Take off switch cover, remove both screws and take off the mounting plate. - Mount the mounting plate onto the flush mounting box with four countersunk screws. Position the plastic decor frame ; supplied by others. - Connect cables: phase to L, neutral to N, light cable (switched phase) to L1. - When connected, position light switch on the mounting plate and reinsert both screws. - Finally, set the rotary code switches on the front side to the desired device address (e.g. E13) with a screwdriver, and note this address down in a list. - Put the switch cover back on.

(not supplied with unit)

Now check the correct operation of the dimmer: - Switch on mains fuse. - Press push-button briefly, the light is switched on. - Press push-button briefly once again. The lighting is switched off. - Now press and hold push-button of some time: the lighting is switched on, its brightness gradually increasing to maximum. When the push-button is released, the brightness of the light stays constant. - Now press and hold push-button for some time: the lighting is gradually dimmed downed to OFF. When the push-button is released, the brightness of the light stays as selected. - Any external push-button wired to terminal 2 as shown above will operate the same way. When the unit receives a message, it will operate as follows: * "OFF" message - full off. * "ON", BRIGHT - brightens from current light level. * "ON" DIM - dims from current light level. * "All lights ON" - brings light 100 % on. * "All units OFF" - full off. As with the other receiver modules, the device address can be changed easily at any time without disconnecting any cables. Important notice: After the installation of the Marmitek X-10 controllers, all receiver modules have first to be checked for correct function and address !

Mini-timer (MT7222)

4 Channel timer/controller
Key Features w Independent on/off timer control of four groups of Marmitek X-10 modules. w Security random lamp switching function. w Buttons to turn on/off and dim 8 light or appliance modules. w 230V ~ 50Hz with battery backup (9 V).

The Marmitek PowerMid Plus sends not only the normal IR command but also RF commands, going through walls and ceilings by means of a built-in RF transmitter. There is no need to point the remote control towards the equipment anymore and equipment can now be controlled from other rooms (e.g. the satellite receiver and video recorder from the bedroom). The PowerMid receiver is positioned in the room where the equipment is placed. When a command is transmitted by the supplied 8 in 1 remote control, the PowerMid receiver will pick up the RF signal and convert it into IR signal. With this signal, the equipment placed in line of sight with the PowerMid receiver can be controlled. The preprogrammed 8 in 1 remote control is capable of operating most brands and models. All these codes are stored in an internal library. The remote control is not only preprogrammed, it is also has a learning function. In an extra learning memory, every command from another IR remote control can be added. The user can determine under which key the learned command needs to be memorized. This makes this remote control very useful for all audio applications while also commands for air conditioners can be logged. The remote control is Marmitek X-10 compatible which means that you can switch appliances and dim lights (in combination with a Marmitek X-10 TM12 Transceiver Module or IR543 IR to PLC Converter).
TECHNICAL SPECIFICATIONS Dimensions receiver: Dimensions remote control: Frequency: Range: Power supply receiver: Power supply remote control: Multiple receivers can be used: Multiple remotes can be used: Works with all brands: 75 x 75 x 110 mm 215 x 60 x 25 mm (max) 433,92 MHz 10-20 meters (50 meters open air) 220 - 240 VAC 50 Hz 2,5 W 4 x AAA 1,5 V batteries (not included) yes yes Except B&O

980202

Wireless wall switch

RW10 - RW12

Key Features w Lets you control two (RW10E) or three (RW12 incl. Dim / Bright) Marmitek X-10 modules in your home. w Sends wireless RF signals to the transceiver module TM12 or to any Marmitek X-10 wireless security system w Compatible with the full range of Marmitek X-10 home automation products.
The wireless wall switch lets you control two ( RW10) or three (RW12) Marmitek X-10 modules from any where in your home. The RW10 has two buttons and can be set to control X-10 modules with codes 1 & 2, or 5 & 6, or 9 & 10, or 13 & 14. This pair of codes is selected by the position of the slide switch inside the battery compartment. The RW12 has four buttons and can be set to control X-10 modules with codes 1 thru 3, or 5 thru 7, or 9 thru 11, or 13 or 15. This group of codes is selected by the position of the slide switch inside the battery compartment. The fourth button is a bright/dim switch allowing you to brighten and dim Marmitek X-10 lamp and wall switch modules which are set to the same unit codes as the group of modules that the RW12 controls. The wireless wall switches are normally used with the TM12 transceiver which passes through all codes from the wireless wall switches onto the powerline to control Marmitek X-10 modules. You can also used the wireless wall switch with any Marmitek X-10 security system instead of the TM12.

Two way PLC interface (TW7223)
Key Features Designed for OEM applications where the controller manufacturer implements their applications using Marmitek X-10 PLC control.
The Two-way PLC Interface (TW7223) has been designed for controller manufacturers to implement X-10 PLC control. The functionality of the PLC control is decided by the controller manufacturer and implemented in the controller panel. The document " X-10 protocol for OEM controller" defines the interface protocol that a manufacturer will need for implementing X-10 control. With a control panel wich has been designed to interface with X-10 PLC, the installation is simple. Just connect the flying lead to the 230V power supply, connect the telephone cable to both the RJ11 socket on the XM10 and the control panel with the cable provided. There is a red LED lamp on the TW7223 wich is ON to indicate power. It will flash when X-10 signals are being received or transmitted.
Supply voltage: Ambient temperature: 230 V +10% -15% 50 Hz - 10 C to + 40 C (operation) - 20 C to + 70 C (storage)
DC Characteristics: Serial data input: Min. logic "1": 4 V input will sink approx 2,5 mA Max. logic "1": 20 V input will sink approx 18 mA Max. logic "0": 0.8 V will sink approx 0,1 mA (Voltages and currents with respect to terminal 2) Note: this output is an open collector transistor. Therefore, the logic "1" voltage is quoted as a reference for defining the output leakage current. An output pullup resistor is required to generate a logic level. The pullup can be returned to any voltage up to 20 V with respect to terminal 2. AC characteristics: HF output to AC power line: Conforms to Class 116 of EN50065-1 Carrier frequency:
60 mW average into 5 load (5 V pk-pk instant.) 120 kHz 2 kHz
Max. phase delay betwen 0 crossing point of AC power line and 0 crossing detect output (either transition): 100 sec Max; allowable delay betwen transitions on 0 crossing detect output and serial data input "0" - "1" transition: 50 sec Max. delay betwen serial input envelope "0" - "1" transition and carrier burst reaching 90 %: 50 sec Width of X-10 enveloppe 1 ms +100 sec -50sec Isolation voltage 4 kV rms 50Hz for 1 min. Approvals: CE Mark
Typical Controller Connection Diagram

5V 10 K

Controller circuits

Transmit output

10 K 100

Transmit input

CONTROLLER

Receive input

Receive output

Ground

Zero crossing input

Zero crossing output

Connection between the controller is via a standard modular phone jack, the connections for which are as follows: 1. 2. 3. 4. B R G Y Zero crossing detect output (with respect to 2). Common. X-10 received envelope output (with respect to 2). X-10 transmit envelope input (with respect to 2).

Universal module (UM506)

230 VAC - 50 Hz - 5 A at 24 VDC LOAD RATING
Key Features w On/Off control of isolated contacts to switch any kind of low voltage load. w Can be set for momentary or sustained contact closure. w Has a beeper to use as an annunciator.
The UM506 contains an isolated contact relay and a piezo sounder (beeper). It can be set to operate as a beeper only, as an isolated contact relay only or both. It can be set for momentary or continous operation for the sounder and/or isolated contact relay. The isolated contact relay are rated for 5 A at 24 VDC. When set to continous operation the relay contacts and/or the module beeps continously when an ON command is received. When an OFF command is received the relay contacts open and/or the beeper stop. When set for momentary operationthe relay contacts close and/or the beeper gives three or four beeps when an ON command is received. The relay contacts then open automaticallyafter about 0,5 second and/or the beeper stops automatically after three or four beeps. In this mode, OFF commands are ignored. The module has a test (ON) button and a unit OFF button.
Supply voltage: Supply current : Making capacity: EMC emission: EMC immunity: Electrical safety: Signal sensitivity: Input impedance: Ambient temperature: Dimensions: 230 V 10% 50 Hz 20 mA capacitive 5 A at 24 VDC according to EN 50081-1 according to EN 50082-1 according to EN 60950 and EN mVpp min 50 mVpp max at 120 kHz 55 (L - N) at 120 kHz - 10 C to + 50 C (operation) - 20 C to + 70 C (storage) 55 x 90 x 38 mm (width x height x depth )