Welcome to the Martin Archery Family. We are confident that you will experience many years of enjoyment from your new Martin bow. Each bow that leaves our door is handmade one at a time as they have been for fifty years. Martin Archery remains a family owned and operated business. We take great pride in every product we produce and we strive to offer you the most complete line of professional accessories available. We welcome any comments you may have about our products. We also like to hear stories of your successes while using our products. If you have any comments, photos, or information you would like to share with us, please call or write. We will do our best to answer any questions you may have. To better serve you, we have the most complete archery manufacturers Web page on the World Wide Web. Our home page includes a hot link directly to our E-Mail box so you can keep in touch with us. Our Web page is located at: www.martinarchery.com Our E-Mail address is: martin@bmi.net Thank You, Gail Martin Founder and President Martin Archery Inc.

TABLE OF CONTENTS

OWNERS RECORD.... 4 PARTS OF THE BOW... 5
BASIC SETUP Cable Guard Installation... 6 Setting Draw Length... 6 Changing draw weight... 7 Setting Tiller.... 7 Wheel Timing (For Two Cam Systems)... 8 Setting Arrow Rest Position... 9 Setting Nock Point... 9 Replacing The Strings... 9 Care And Storage.... 9 THE FUZION SINGLE CAM SYSTEM Adjusting The Draw Length... 10 Setting The Tiller.... 10 Using The Adjustable Perimeter Weight.. 11 String Configuration... 11 THE FURY CAM Getting Peak Performance... 12 Cam Positioning... 12 THE Z CAM Setting Draw Length... 6 Changing draw weight... 7 Setting Tiller.... 7 FINE TUNING YOUR COMPOUND BOW Bare Shaft Planing Test... 13-14 Paper Tuning... 15-17 SUPER FINE TUNING Short Range Group Tuning... 18 Flight Tuning Broadheads... 19 TEN COMMANDMENTS OF ARCHERY SAFETY.. 20 FREQUENTLY ASKED QUESTIONS.. 21 MARTIN WARRANTY... 22

OWNER'S RECORD

BOW MODEL: __________
LIMB TYPE:_________________________________
CAM:_________________________________ DRAW WEIGHT:_________________________________ DRAW LENGTH:_________________________________ STRING LENGTH:_________________________________ PURCHASED FROM:_________________________________
DATE:_______________________________

NOTICE:

STAPLE YOUR SALES RECEIPT HERE. PROOF OF PURCHASE DATE IS NEEDED SHOULD YOU EVER REQUIRE WARRANTY WORK.

PARTS OF THE BOW

Idler Wheel Axle Split String Upper Limb Shooting String Limb Bolt Riser Slide Slot Rest Mounting Hole Grip Stabilizer Insert Limb Pocket Barrel Nut Quiver Mounts Up-Mount Cable Guard Lock Mount Rest Mounting System

Lower Limb

Adjustable Perimeter Weight (Optional) Fuzion Cam
(Cougar 2000 with Fuzion Cam System) 5

BASIC SETUP

Your new Martin bow takes little setup to get started shooting. Please read and familiarize yourself with these starting procedures before shooting. Many of these procedures will have been completed by your authorized Martin dealer. After completing these simple steps, you will be more accurate and will have greater success from the start. A careful and thorough initial setup will make the tuning process much easier.

CABLE GUARD INSTALLATION

The Jaguar Fuzion and Jaguar Magnum models are equipped with an upper mounted cable guard that mounts to the risers 10-24 threaded mounting holes. Specially Cable designed for use with the short axle lengths and FuzGuard ion single cams utilized by these models, this mount incorporates a dove-tail slide for mounting sights and quivers. All other Mar tin compound bow models* feature smooth bore holes in the riser that allow direct, bracket-free installation of the cable guard rod. There are set screws within the riser that will secure the rod. The cable guard rod should be rotated toward the grip to provide adequate fletching clearance. Caution should be taken against over-rotating the rod as excessive clearance can cause unnecessary pressures on the limb tips and axle bushings. Only 9/16 off-set is necessary to provide adequate fletching clearance. Though most bow models allow either an upper (above the arrow rest) or lower (below the grip) mounting, Martin Archery recommends the upper mounting position on all Fuzion single cam models. *As of this writing, the Scepter II and Bobcat models did not allow the direct installation of a cable guard rod. A mounting bracket is supplied with these models that threads into the threaded holes provided in the back of the riser.

SETTING DRAW LENGTH

Z Cams and Mini Z Cams The Z Cam uses draw length modules to adjust the draw length. The size of each module is designated by a number followed by an 'X'. These modules are sized from 2X to 9X. The 9X makes the longest draw and the length decreases one inch for each number. To change the draw length on these cams, simply remove the two screws holding the module to the cam. Take a look at the module number and select a new module that will give you the correct draw length. Install the new modules, making sure that the numbers on each module match.

Fury Cams

The Fury Cam is a draw length specific cam. Each cam was designed to give peak performance and speed at each specific draw length. Therefore, changing the draw length requires changing to a different size cam. NOTE: Do not draw your bow without the modules installed. It will cause damage to your harness system. Fuzion Single Cam System A full explanation on the Fuzion Cam System, including changing the draw length, can be found on page 10 and 11.

CHANGING DRAW WEIGHT

Martin bows have a fifteen pound draw weight range. Using the 3/16 Allen wrench supplied with each bow, you will turn the limb bolts clockwise to add weight and turn counter clockwise to reduce weight. One complete turn on each limb bolt provides about 4 pounds of adjustment. TIP: Mark a line on each limb bolt in white-out or white paint marker to make it easier to keep track of how far you are turning each bolt. NOTE: Do not shoot your bow with the limb bolts more than 5 turns out from the riser.

SETTING TILLER

After setting the draw weight on your bow, you will need to set the tiller measurement to make sure that you have adjusted your limbs properly. On all Martin compound bows, 0 tiller will shoot perfectly. However, the tiller measurement can vary up to 1/4 closer at the bottom. There is no set measurement that provides peak performance for every shooter. To measure your tiller, simply measure from the limb pockets to the string on both ends of the bow (see Fig.1). You can custom fit the feel of your bow by experimenting with the tiller setting. Start with even tiller, when both top and bottom limbs are adjusted the same. (Before adjusting your limb bolts, mark a white line from the center of the limb bolt to the outside. This will help you keep track of your settings.) By tightening one bolt a quarter turn at a time you will begin to affect the steadiness of your setup. If the bow begins to become unsteady, move the tiller back to even and tighten the opposite limb bolt. After finding the best spot, make a note so if you ever change the draw weight you can reset the tune where you had it shooting best (i.e., 3/4 bottom would mean three quarters of a turn on the bottom limb bolt). NOTE: Your peep sight position and your nock point will change as you turn one limb bolt. Take measurements and correct your nock and peep each time you turn your bolts.

WHEEL TIMING (FOR TWO CAM SYSTEMS)
It is important for consistency and accuracy that your bows cams roll over at the same instant and are in the same position when you are at full draw. Your cams should be synchronized or timed to your particular style of shooting. To check the timing, draw your bow with your fingers or release just as you would while shooting. Different drawing methods will affect the roll over of your cams. Draw the bow using your exact shooting method. Cams are in perfect time. Upper Cam is over-rotated and out of sync with the bottom cam
Adjust this yoke by twisting up the bottom Split String cable.
Adjusting timing using the Split String System (synthetic cables) This procedure can be expertly performed by your String Anchor local archery professional. You will need a bow press or a bow stringer to adjust your timing using the Split String System. First, determine which cam is ahead, or out of sync. The Split Strings, or buss cables, should Split reach the end of the cable grooves on the Power String Side (back side) of each cam at the same time. Then, while the bow is relaxed, remove the appropriate Split String off its outside posts and twist in a direction that shortens or tightens the cable. A few turns will go a long way so proceed sparingly. If your top cam is ahead, or rotates further than your bottom cam, twist the bottom Split String, do the opposite if the bottom wheel is ahead. After these steps are completed make sure that all of your string loops are firmly secured on their appropriate pegs before the pressure is reapplied to the bow. NOTE: Back your bow limbs out five turns from the riser before using a bow stringer or a bow press. Only let a qualified professional put your bow in a bow press.
SETTING ARROW REST POSITION
After your arrow rest is installed on your bow, you will need to set the rest to the best centered location to begin tuning. The easiest way to do this is to visually align the bowstring in the center of the grip section. If you are shooting your bow with Bowstring a release aid, the prongs or blade of your shoot-through rest will need to be centered with the bow string. During tuning, your arrow rest may need to be moved in or out from its centered location. This is normal because different shooters apply different pressures to the bow. Finger shooters will need to position the rest so that the point is about 1/8 outside the string. This is to compensate for the horizontal bending of the arrow upon release. An arrow rest that provides some side support, such as a cushion button, for the arrow is best for finger shooters.

SETTING NOCK POINT

Place a bow square on the string and slide the square down until it rests on your arrow rest. Then place a moveable nock set on the string. Using the measuring scale on the bow square, set the nock set at the proper location on the string. A good starting point for finger shooting is 1/4 high, measuring from the bottom of the nock set to 90 on the bow string. Start at high if you are using a release aid. If you do not have a bow square, you can snap an arrow on the string and visually level the arrow. Then crimp your nock set. In a pinch, this will get you to a good starting location.

1/2 1/4 900

REPLACING THE STRINGS
Should your string need replacing, it is best to go to your Martin dealer and have it expertly done. It is recommended that you replace your string once a year or anytime it shows wear. Always be sure that the string you replace it with is the correct length and material for your bow.

CARE AND STORAGE

When properly cared for, your new Martin bow will give you years of trouble-free service. When your bow is new it will require no lubrication. Over time you may need to lubricate your cams to guard against friction and noise. Use a dry lubrication such as Teflon spray powder or graphite powder. Do not use wet or oily lubrication. Using a wet type lubrication will attract grit and dust that may cause premature wear in wheel bushings. A good rule of thumb when caring for your bow is to keep it as comfortable as you are. If it is too hot for you, it is too hot for your bow. If it gets wet, dry it off completely. Periodically clean your bow with a wet rag and mild soap to remove mud or dust (caution: do not store until completely dry). Prolonged exposure to extreme heat may cause failure in your bow limbs and excessive stretch in your harness system. It will not hurt your bow if it is rained on while shooting, but make sure it is completely dry before storing in a bow case to guard against rust or corrosion.
THE FUZION SINGLE CAM SYSTEM
The Fuzion system is unique among all other single cam systems. The Fuzion system has an Adjustable Perimeter Weight, modular draw length adjustment, and can be adjusted in half inch adjustments within each draw length module.
ADJUSTING THE DRAW LENGTH

The Fuzion Single Cam System boasts a revolutionary design and is engineered to give you peak performance and speed. Using draw length modules, the draw length can be adjusted in 1" increments (see fig. 1) The modules can also be used to adjust the let-off. A high let-off module is marked as F-#. A 65% let off module is marked with a F-#\. The slash on the end of the size number indicates 65% let-off. To change the draw length replace the module on the cam by removing the screws that hold it to the cam (see Fig.3). NOTE: do not draw your bow without the module installed. It will damage your harness. The Fuzion module sizes range from F-2 to F-7. If you would like to increase the draw length select a higher number. If you would like to decrease the Fig.1 draw length select a lower number. The draw length can also be adjusted up or down " using the pegs on the back of the cam (see fig.1). The #2 peg is the prescribed draw length for each module. The #1 peg is " longer and the #3 peg is " shorter. The draw weight will change one pound, accordingly, when using the peg adjustment.

SETTING THE TILLER

Your Fuzion bow should start out with an even tiller setting. Even tiller, or "0" tiller, makes sure both limb bolts are adjusted evenly. Single cam systems do not allow the string to be parallel with the riser. The tiller cannot be measured in a standard manner. To check the tiller on the Fuzion System, stretch a thin string or dental floss from axle-to-axle and measure from each limb cup to the dental floss. (see Fig.2)
USING THE ADJUSTABLE PERIMETER WEIGHT (OPTIONAL)
The Adjustable Perimeter Weight in the Fuzion system is used to enhance smoothness and speed. Different models, bow weights, draw lengths, and arrow weights will cause the Perimeter Weight to affect performance differently. By changing the position of the Perimeter Weight, adding a second weight, or leaving the weight out altogether, you can custom tune your Fuzion bow to your own personal preferences. Fuzion Module #3054 F2 - F7
Perimeter Weight #3053 Slot for weights BP-6 module screws

Fuzion Cam #3050

STRING CONFIGURATION
The string harness on the new Fuzion are installed according to the diagram below (see Fig.4). Your string harness should be installed by your qualified Martin dealer.

Shooting String

Split String

THE FURY CAM

GETTING PEAK PERFORMANCE
The Fury Cam is designed to provide optimum performance when the draw weight is at its maximum setting. In order to attain the top performance expected from this Cam system, it is strongly recommended that the draw weight be set at its maximum. This setting will also keep noise to a minimum and benefit accuracy.

CAM POSITIONING

In order to achieve the ideal draw force curve and resulting maximum efficiency, the Fury Cams need to be positioned properly. Though the exact cam position is not critical, the straight section of the cam should be aligned vertically and parallel with the bowstring (see diagram). No exact measurement is required, just a visual check will be sufficient. Should the bow string stretch abnormally, the straight section of the cam can rotate closer to the bowstring, increasing draw length and draw weight while adversely affecting performance. Add twists to the bowstring to reduce its length and return the cam back to its proper alignment. Proper cam positioning as seen on the bow.This positioning applies to any bow using the Fury Cam.
Proper orientation of string and Cam point.
FINE TUNING YOUR COMPOUND BOW
After completing the basic setup procedures, you are now ready to fine tune your setup for the best accuracy possible. There are four tuning methods described in this section. Some of these methods may not apply to certain styles of shooting. Read the introduction to each method carefully to make sure it applies to your shooting style.

BARE SHAFT PLANING TEST

The Bare Shaft Planing method of tuning works best when using a finger release. To begin the Bare Shaft Planing test you will need three fletched arrows and one or two bare shafts. You will also need a target that will catch the arrows without allowing the arrow to kick as it stops in the target. This test will help you establish the correct nock and rest position, and it will tell you if your arrow is the correct spine. Porpoising and Fish Tailing describe the different flight disturbances you will encounter while tuning. Porpoising Porpoising is identified by an up and down kick during arrow flight and relates to the nock point adjustment. It is important to correct porpoising first because small left and right disturbances could be nock point related. Start at about ten to fifteen yards and shoot three fletched arrows into your target. Using the same aiming point, follow them up with a bare shaft. After you get the shafts to impact with the fletched shafts, you may want to try shooting them at a longer distance for a finer indication of arrow flight.

A high nock set will cause porpoising If the bare shafts impact below the fletched arrows, your nock point is too high. Move your nocking point down in small increments until the bare shaft strikes with the fletched shafts. If the bare shafts impact above your fletched arrows, your nock point is too low. Lower your nock point in small increments until your fletched arrows and your bare shaft impact together. Repeat the above steps from a longer distance to make sure you have completely corrected the nock point. Shooting from a longer distance will make minor disturbances more apparent.

Low nocking point

High nocking point
Fishtailing Fishtailing relates to the arrow rest adjustment and the stiffness of your arrow. Just as before, start at about ten to fifteen yards and shoot three fletched arrows into your target. Using the same aiming point, follow them up with a bare shaft. After you get the shafts to impact with the fletched shafts, you may want to try shooting them at a longer distance for a finer indication of arrow flight.
If your unfletched shafts impact to the left of your fletched shafts, your arrow is too stiff. There are several things that you can do to correct this problem; you can select a weaker arrow, you can decrease the cushion plunger tension. Increasing the peak weight of your bow or increasing your point weight will also make your arrow act a bit more limber. If your unfletched shafts impact to the right of your fletched shafts, your arrow is too limber. There are several methods you can try that will correct this problem; you can select a stiffer arrow, you can increase the cushion plunger tension. Decreasing the peak weight of your bow or decreasing your point weight will also make your arrow act a bit more stiff. To further fine tune your setup, step back to twenty or thirty yards and repeat the above procedures. Small flight disturbances will show up better as you get farther from the target. Your Martin bow is essentially tuned when your bare shafts hit together with your fletched shafts. Keep in mind that if you continue and complete the super fine tuning methods in this manual, it is not uncommon for your bare shaft impact to change. Your bow will be shooting its best and it is common for a perfectly tuned bow to shoot a bare shaft a bit low and right or low and left. Perfect arrow groups are the goal when completing these exercises.
Stiff Arrow- bare shafts fly to left.
Limber Arrow-bare shafts fly to right.

PAPER TUNING

Paper tuning will work for all styles of shooting. As you are going through these steps keep in mind that paper tuning is not chiseled in stone as the law of archery. It is a guideline for clean arrow flight. Many shooters find that their setup groups best when achieving less than perfect tuning results. For example, some target shooters set their bows to tear slightly high through the paper. They feel this makes their arrow flight less likely to be influenced by outside variables like wind or rain and helps arrow clearance when using a shoot-around type rest such as a blade or pan type launcher. To begin paper tuning, set up a frame or rack with paper suspended from the frame. Position the frame far enough away from your backstop so the arrow can completely clear the paper. Stand about ten feet from the paper and make sure your arrow is level as it flies through the paper. Fire a test shot and read the results. Compare the holes you have made in the paper to the diagrams below. Procedures for correcting the tear are listed next to each diagram. Please note that tuning procedures recommended for finger shooting often differ from those used for release shooting. You will find that the arrow spine reaction is different for fingers and release, therefore, the procedures for correcting the different disturbances vary. Follow the instructions carefully for your particular shooting style.

HIGH TEAR (fletching tears above point)
This tear may signal: Nocking point too high. Lower the nocking point. Improper vane clearance. See if arrow fletching is hitting the rest. Launcher is too stiff (release shooters). Weaken spring tension or use a more limber launcher. Wheels may be out of time. Check wheel timing. Arrow may be too limber Select a stiffer arrow shaft. Tiller adjustment may be incorrect. See basic setup section page 7. Irregular or inconsistent shooting form. See a qualified archery coach or professional and have them check your technique.
LOW TEAR (fletching tears below point)
This tear may signal: Nocking point too low. Raise the nocking point. Wheels may be out of time. Check wheel timing. Tiller adjustment may be incorrect. See basic setup section on page 7. Irregular or inconsistent shooting form. See a qualified archery coach or professional and have them check your technique.
RIGHT TEAR (fletching tears to theright of point)
This tear may signal: Note: If you are left handed follow these instructions in reverse. FINGERS: Stiff arrow. This problem is cured using the following methods: a. Increase peak weight. b. Use a heavier point. c. Select a more limber arrow. d. Lighten cushion plunger tension, or use a weaker spring on shoot around rests. e. Make small incremental rest adjustments towards the bow. RELEASE: Arrow rest is too far to the right. Move arrow rest to the left. EITHER STYLE: Too much pressure on the cable guard. Rotate cable guard for minimum fletching clearance. Irregular or inconsistent shooting form. See a qualified archery coach or professional and have them check your technique. Clearance problem. See that arrow has adequate fletching clearance.
LEFT TEAR (fletching tears left of point)
This tear may signal: Note: If you are left handed follow these instructions in reverse. FINGERS: Weak arrow or a clearance problem. This problem is cured using these methods: a. Reduce bow weight. b. Use a lighter point. c. Select a stiffer arrow. d. Increase cushion plunger tension or use a stiffer spring on shoot around rests. e. Make small incremental rest adjustments away from the bow. RELEASE: Arrow rest is too far to the left. Move the arrow rest to the right. Arrow is too stiff. Decrease bow weight or select a weaker arrow. EITHER STYLE: Arrow is not properly clearing cables. Rotate cable guard for minimum fletching clearance. Irregular or inconsistent shooting form. See a qualified archery coach or professional and have them check your technique. Clearance Problem. See that arrow has adequate fletching clearance.

MULTIDIRECTIONAL TEAR

This tear may signal: More than one problem with accessory adjustment. Move nock adjustment first until the tear is horizontal and follow instructions for horizontal tear. Clearance Problem. See that the arrow has adequate fletching clearance. Wheels may be out of time. Check wheel timing. Irregular or inconsistent shooting form. See a qualified archery coach or professional and have them check your technique.

PERFECT HOLE

This pattern shows clean arrow flight. The point and fletching impacted the same location. Your bow is now ready to shoot or you may want to continue and try some of the super fine tuning methods.

AFTER ADJUSTING

After you have completed these steps and have achieved good paper test results, it is best to try it at fifteen and twenty feet just to make sure you did not get a false reading. A good rule to go by when paper tuning is to move your nock point or arrow rest opposite the tear when using a release. In some rare cases if this does not clear up your tear you may need to move your accessories in the same direction as the tear.

SUPERFINE TUNING

SHORT RANGE GROUP TUNING
Short range group tuning will work with any style of shooting. Best results are achieved when this method is used after completing the Bare Shaft Planing or Paper Tuning tests. This is a good ultra fine tuning method when space will not permit long range shooting. After completing the following steps you will have very clean arrow flight and a well tuned, accurate setup. To begin the short range tuning method, you will need a piece of cardboard, or a target face will do nicely. Make a broad line through the center of the paper on the blank side, making sure the line is thick enough to see from twenty yards. Start at about 10 to 15 yards from the target. Use your tuning target and position the line vertically when you are tuning the arrow rest and position the line horizontally when you are tuning the nock point. This pattern shows a vertical disturbance. This pattern shows a clean vertical pattern.
Vertical Impact Position your line horizontally and shoot six arrows at the line. Concentrate on keeping your pin on the line. Dont worry about left and right hits, just try to keep your shots on the line. Shoot two good groups, discarding any rough or bad shots, and note the vertical impact of the arrows and their relationship to the line. All adjustments are made with the nock point during these steps. If your arrows are not consistently grouping on the line, make small 1/32" adjustments up or down with the nock point and shoot two more groups. Continue making nock adjustments in small increments. If all of your arrows begin to hit on the line you are correcting the nock position. In the event that your groups widen, move your nock back to its original location and make small adjustments in the opposite direction. This pattern This pattern shows a clean shows a horizontal horizontal pattern. disturbance. Horizontal Impact After achieving a nice, straight, horizontal pattern, rotate your target so your line will appear vertical. Just as before, shoot two good groups, discarding any rough or bad shots, and note the horizontal impact of the arrows and their relationship to the line. All adjustments are made with the arrow rest during these steps. If your arrows are not consistently grouping on the line, make small 1/32" adjustments left or right with the arrow rest and shoot two more groups. Continue making rest adjustments in small increments. If all of your arrows begin to hit on the line you are correcting the rest position. In the event that your groups widen move your rest back to its original location and make small adjustments in the opposite direction.

FLIGHT TUNING BROADHEADS

Broadhead tuning will work for all styles of shooting. After you have completed one or more of the tuning procedures described in this manual, you can proceed with this final test to get your new bow ready to hunt. You will need three fletched arrows with field tips and three with broadheads that weigh the same as your field tips. Before you begin shooting, you will need to check your broadhead equipped arrows. After installing your broadheads, make sure they are perfectly straight on the shaft. This can be done by spinning the arrow on a flat counter while checking for any broadhead wobble. You can also use a commercially made spin check tool that is available from your dealer. After all of your broad heads are spin-checked and straight you are ready to begin. Set up a broadhead target at twenty or thirty yards and shoot three arrows with field tips. Make sure you are properly warmed up and you are shooting to the best of your ability. Next, shoot three identically aimed arrows with broadheads. WARNING: NEVER SHOOT BARE SHAFTS WITH BROADHEADS ATTACHED. THE FLIGHT WILL BE EXTREMELY UNPREDICTABLE AND DANGEROUS. Once you have shot the best group you can shoot, compare the position of the broadhead group to the field tip group. Compare the groups to the diagram below and make very small incremental adjustments as described next to the broadhead group that corresponds to your arrow pattern. Note: make very small 1/32" adjustments. A small adjustment will greatly change your broadhead flight. High Flight Multidirectional Flight Correct the nock point first. Raise nock point Once the arrow is straight left, follow instructions for left flight. Left Flight Release: Move arrow rest to the right in small increments. Fingers: Slightly increase draw weight. Use a heavier broadhead. Decrease cushion plunger tension. Move plunger toward the bow in small increments. Reverse steps for left hand shooter. Field Point Group Broadhead Group Right Flight Release: Move arrow rest to the left in small increments Fingers: Sightly decrease draw weight. Use a lighter broadhead. Increase cushion plunger tension. Move plunger away from the bow in small increments. Reverse steps for left hand shooter. Low Flight Lower nock point
TEN COMMANDMENTS OF ARCHERY SAFTY
Never - Dry fire your bow or shoot it without an arrow. This will result in damage to your bow. Never - Let anyone draw or shoot your bow if their draw length is longer than yours. Over drawing of the bow can cause cable damage. Never - Draw, aim, or shoot your bow unless you are sure that the line of fire is clear. Remember, once an arrow is fired it cannot be recalled. Never - Shoot an arrow that is less than five grains per pound. For example, an 80# bow requires a minimum of 400 grains of arrow weight. Less than five grains per pound of arrow weight simulates a dry fire effect and may damage your bow. Never - Expose your bow to extreme heat. Excessive heat, such as your car on a hot day, could lead to limb failure and premature wearing of the string harness. Always - Check all of your arrow shafts and nocks upon removal from the target. Do not shoot any arrows that show defects or broken nocks. Always - Carefully inspect your bow after each use. Be sure all screws are snug and accessories are tight. Inspect your string and cables for wear or damage. Always - Draw your bow while pointing it at the target. A premature release of the arrow can be very dangerous. If you cannot draw your bow while pointing it at the target without excessive movement, lower the peak weight of your bow until you can draw smoothly and correctly. Over time you will build up strength, and will be able to return to the higher weight. Always - Draw your bow with an arrow on the string while keeping it pointed in a safe direction. Never draw your bow with a release aid without an arrow. A release aid failure could result in the dry fire of your bow. Always - Back your limb bolts off five full turns from the riser before putting it in a bow press. Only let a qualified professional or a Martin authorized dealer put your bow in a bow press. Inexperienced use of a bow press or a T-stringer can result in damage to your bow. This type of damage caused by a press is not covered under the Martin Archery bow warranty.

FREQUNTLY ASKED QUESTIONS
It is our goal at Martin Archery for you to realize your full potential as a new member in the Martin family. We have some of the greatest shooters in the world shooting with us and we are certain you can become one of them. Below are some of the most commonly asked questions about Martin archery equipment. We hope that these questions are useful to you. What arrows should I use with my Martin bow? It is very important for accurate shooting that your arrows are the correct spine, or stiffness, for your bow. Arrows that are too limber or too stiff will cause tuning and accuracy problems. Your local dealer has an arrow chart and can properly fit your bow with the correct shaft. Regardless of the material or manufacturer of the arrow, all arrows have to be the correct spine or stiffness for your bow. How is the draw length on my Martin bow measured? Martin Archery currently measures draw length according to the recommended AMO standard. This standard dictates that the draw length be measured 1 forward of the pivot point, or most inward point, of the grip. How can I make my Martin bow as quiet as possible? Though your bow is engineered to produce very little noise, it is important to remember that high performance models, that store high levels of energy, are not generally as quiet as moderate performance bows. A few ways to eliminate noise and vibration are: a. Install string silencers. b. Make sure all screws on your setup are snug (a small amount of Lock-Tite will help keep them tight). c. Set your draw weight closer to its maximum, lower settings can increase vibrations and noise. d. Use a heavier arrow in order to absorb more of the bow's stored energy. e. Install mole skin between any attached accessory and the bows riser. At what weight setting will my bow perform best? Your Martin bow can be shot anywhere within its fifteen pound weight range. You will achieve the highest level of performance from any compound bow when it is set at its maximum draw weight. The maximum draw weight setting maintains the engineered level of limb, cable, and bowstring tension for peak efficiency, while keeping noise and vibration to a minimum. I want to get the most arrow speed possible. How light can I make my arrows without causing damage to my bow? The durability of Martin bows is unsurpassed in the archery industry. All components of your new bow can withstand high levels of stress. Its unprecedented durability allows your Martin bow to easily use an arrow that weighs as little as 5 grains per pound of draw weight. Note: The Martin Archery warranty does not allow the use of an arrow weighing less than five grains per pound. What kind of string material can I use on my Martin bow? The strength of all Martin bows, regardless of what cable system you are using, allows the use of all of the low stretch materials in use today. S-4, Spectra FastFlight, and 450 Premium among others are all good materials, and they can be used on all martin bows with out voiding your warranty.

WARRANTY

Whether your new bow is for hunting, 3-D, or for target shooting, you have made the right decision in choosing a Martin! Over forty years of archery experience are built into every Martin bow. You can be confident that your new bow is designed to provide years of faithful service, and Martin will always be around to back it with our rock solid warranty. LIMITED 5-YEAR WARRANTY Your Martin compound bow is guaranteed by Martin Archery, Inc. to be free from defects in materials and workmanship for a period of two (2) years from the date of purchase. Exceptions to this warranty include the bow string and synthetic cables, for which there is no warranty. During the remainder of this Limited Five Year Warranty, Martin Archery, Inc. will offer repairs or replacements at a cost of 50% the current suggested list price. The warranty is conditioned upon proof of date of purchase and other conditions listed below. IT IS IMPORTANT THAT YOUR SALES RECEIPT BE FILED IN A SAFE PLACE FOR FUTURE REFERENCE, AS REPAIRS WILL NOT BE PERFORMED UNDER WARRANTY WITHOUT A COPY OF THE DATED SALES RECEIPT. Martin Archery, Inc. warrants that your Martin compound bow will perform its intended function if used in accordance with the instructions provided. This Limited Warranty covers only the replacement parts, labor, and return ground transportation costs performed by Martin Archery Inc. to the customer. Transportation for the return of the bow to Martin Archery, Inc. are not covered. No C.O.D. shipments will be accepted by Martin Archery, Inc. Warranty repairs can be performed by an Authorized Martin Dealer, for which Martin Archery, Inc. will cover replacement parts and ground transportation costs to the Authorized Dealer. Labor costs for warranty repairs performed by Authorized Dealers are not covered by Martin Archery, Inc. Martin Archery makes no other warranty either expressed or implied, whether of fitness or of marketability, except as stated above. Any such additional warranty is expressly disclaimed. Warranty limitations are as follows: 1. If bow shows signs of misuse, alteration, or mishandling this warranty will be void. Use of arrows weighing less than five (5) grains per pound of draw weight is considered misuse and will void this warranty. 2. Claimant must be the original purchaser. This warranty is not transferable. 3. All returns to Martin Archery Inc. must be pre authorized. Owner must contact Martin Archery, Inc. at (509) 529-2554 prior to shipping in order to obtain a Return Authorization number. 4. All accessory items must be removed from the bow prior to shipping. Martin Archery, Inc. will not be responsible for damage or loss of any accessory item left on the bow. 5. Warranty is not effective unless a copy of the dated sales receipt accompanies the bow. 6. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. * After acquiring a Return Authorization number, send bow to: Martin Archery, Inc. Rt. 5, Box 127 Walla Walla, WA 99362