Use & Care Guide

Table of Contents
Important Safety Instructions 1-2 Operating Tips. 3-4 Using the Controls
3 Speed Select Models. 5-Speed Select Models. 7-8 Electronic Control Models.9-11
Special Features. 12-13 Care & Cleaning. 13 Troubleshooting. 14 Service & Warranty. 15 Guide dutilisation et dentretien. 16 Gua de uso y cuidado. 34

Form No. A/06/05

Part No. 6 2621890

www.maytag.com

Litho U.S.A.
2005 Maytag Appliances Sales Co.
Important Safety Instructions
Installer: Please leave this guide with this appliance. Consumer: Please read and keep this guide for future reference. Keep sales receipt and/or canceled check as proof of purchase. Model Number _______________________________ Serial Number ________________________________ Date of Purchase ______________________________ If you have questions, call: Maytag Customer Assistance 1-800-688-9900 U.S.A. 1-800-688-2002 Canada (Mon.-Fri., 8am-8pm Eastern Time) Internet: http://www.maytag.com U.S. Customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080. In our continuing effort to improve the quality and performance of our appliances, it may be necessary to make changes to the appliance without revising this guide. For service information, see page 15.

WARNING! FIRE HAZARD

Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode. Do not wash articles which have been previously cleaned, washed, soaked, or spotted with gasoline, dry-cleaning solvents, oil, waxes, chemical solvents, alcohol, turpentine, or other flammable or explosive materials. These substances will be retained in articles, and articles which still contain these flammable or explosive substances give off vapors that could ignite or explode. Observe these precautions when using cleaning fluids, spot or stain removers, etc. These products should be labeled nonflammable. Use according to manufacturers directions in a well ventilated area or outdoors. Thoroughly rinse articles by hand before placing them in the washer. Some of these products rust removers for example will damage components and the finish of the washer. Keep area around and underneath washer free from the accumulation of combustible materials, such as lint, paper, rags, gasoline, and all other flammable vapors and liquids. HYDROGEN GAS IS EXPLOSIVE! Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. If the hot water system has not been used for such a period, before using the washer, turn on all the hot water faucets and let the water flow from each faucet for several minutes. This will release any accumulated hydrogen gas. As this gas is flammable, do not smoke or use an open flame during this time. Recent studies have shown that if vegetable oil contaminated materials are incompletely washed, a carry-over and buildup of the oil may contribute to a chemical reaction (spontaneous combustion) that could cause a load to catch fire by itself. This would be more likely to happen if the load were left in the dryer after tumbling stopped or if items were folded and stacked while warm.
What You Need to Know About Safety Instructions
Warning and Important Safety Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur. Common sense, caution and care must be exercised when installing, maintaining or operating appliance. Always contact the manufacturer about problems or conditions you do not understand.
Recognize Safety Symbols, Words, Labels WARNING
WARNING Hazards or unsafe practices which COULD result in severe personal injury or death.

CAUTION

CAUTION Hazards or unsafe practices which COULD result in minor personal injury.

WARNING

To reduce the risk of fire, explosion, electric shock, or personal injury when using your washer, follow basic safety precautions, including the following:
1. Read all instructions before using the appliance. 2. As with any equipment using electricity and having moving parts, there are potential hazards. To use this appliance safely, the operator should become familiar with the instructions for operation of the appliance and always exercise care when using it. 3. Do not install or store this appliance where it will be exposed to the weather. 4. Install and level washer on a floor that can support the weight. 5. This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. 6. To avoid the possibility of fire or explosion: a. Do not wash items that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode. Hand wash and line dry any items containing these substances. Any material on which you have used a cleaning solvent, or which is saturated with flammable liquids or solids, should not be placed in the washer until all traces of these liquids or solids and their fumes have been removed. These items include acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes and wax removers. b. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode. c. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time. d. Do not wash or dry items that are soiled with vegetable or cooking oil. These items may contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself. 7. Do not reach into the appliance if the tub or agitator is moving. 8. Do not allow children or pets to play on, in, or in front of the appliance. Close supervision is necessary when the appliance is used near children and pets. 9. Do not tamper with controls. 10. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in published user-repair instructions that you understand and have the skills to carry out. 11. Unplug power supply cord before attempting to service your washer. Service is to be done only by qualified service personnel. 12. The agitator should not be removed. If the agitator is removed, it must be replaced by pushing down completely and the locking screw tightened before the washer is operated. 13. Keep all laundry aids such as detergents, bleach, etc., out of the reach of children, preferably in a locked cabinet. Use laundry aids only as directed by the manufacturer. Observe all warnings on container labels. 14. Keep the area around and underneath washer free from the accumulation of combustible materials, such as lint, paper, rags, gasoline, and all other flammable vapors and liquids. 15. Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash. Hazardous fumes can form. 16. Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and cause skin irritation. 17. For flame resistant finishes - follow garment manufacturer's instructions carefully. Improper laundering could remove the finish. 18. Before the appliance is removed from service or discarded, remove the door to the washing compartment. 19. Inlet hoses are subject to damage and deterioration over time. Check the hoses periodically for bulges, kinks, cuts, wear or leaks and replace them every five years.

SAVE THESE INSTRUCTIONS

Operating Tips

Detergent

Use either liquid or granular laundry detergent. For best results, be sure detergent is added to the washer BEFORE the load and be sure the wash water is above 60 F. Use the correct amount of detergent for the load size, soil level and water conditions. Use more detergent if you have hard water and very soiled loads. If you have soft water or a lightly soiled load, use less detergent. (See manufacturers instructions.) Wipe up any detergent spills on the washer.

Loading

For best results add the detergent to the washtub before adding the load. Put dry, unfolded clothes loosely in the tub, up to the top row of holes for a maximum load. Do not wrap large items like sheets around the agitator. Mix large and small items for best circulation. Wash bulky items like blankets separately. When laundering wrinkle-free items or items of delicate construction, washable woolens or loosely knit items, never use less than the MEDIUM water level setting. This will minimize shrinkage, wrinkling and pulling of seams. Close lid carefully to avoid slamming.

Additional Tips

During the spin, it is possible for the load to become unevenly distributed in the tub. If this happens, push in the control dial, open the lid, redistribute the load, close the lid and restart the washer. The spin will resume at the point it was interrupted. The washer will pause briefly throughout each cycle. These pauses are normal. This washer is designed so that it will not agitate or spin when the lid is open. It will, however, fill with the lid open so water is available for pretreating stains or diluting fabric softener. If you open the lid during a spin cycle, the washer will stop. When the lid is closed and the washer is restarted, the washer will continue the cycle at the point it was interrupted.
Using the Controls 3 Speed Select Models

STEP 1

Select Water Level
Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation. It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust the water level, turn the control to reset and then back to the desired setting. WATER LEVEL SETTING Mini Small Medium Large Super LOAD SIZE 1/4 Full 1/4 - 1/3 1/3 1/2 1/2 2/3 3/4 Full Automatic Temperature Control (A.T.C.) (select models) provides the optimal wash water temperatures for cleaning. To save energy, the Automatic Temperature Control will regulate wash water temperatures by mixing hot and cold water to reach the proper water temperature.

WASH/RINSE TEMPS LOAD TYPE
Note: Items must circulate freely for best results.
Select Wash/Rinse Temperature
Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water (select models) for rinsing. Use the chart below as a guide. WASH/RINSE TEMPS Hot/Cold Warm/Warm (select models) Warm/Cold Cold/Cold LOAD TYPE White and heavily soiled, color-fast items. Moderately soiled, colored items. Moderately soiled, colored items; most wrinkle-free items. Brightly colored, lightly soiled items; washable woolens.
These settings feature Automatic Temperature Control: Saves energy by adding cold water ATC Hot/Cold, to the hot water from your water ATC Warm/Cold ATC Warm/Warm heater. Provides optimum cleaning (select models) at lower temperatures. May add hot water to the incoming cold water as the washer fills. This ATC Cold/Cold assures that the water will be warm enough to properly activate detergent.
Note: In wash water temperatures below 60 F,
detergents do not dissolve well or clean well. Care labels define cold water as up to 85 F.
Control features vary by model.

Extra Rinse

Select Cycle
To select a cycle, push the control dial in (off position) and turn it to the right (clockwise) until the pointer is at the soil level needed for the wash load in the Regular, Wrinkle Control or Delicates cycles.
Select Options (if desired)
When the switch is in the On position, an additional rinse at the end of the Regular, Wrinkle Control and Delicates cycles is provided to more completely remove laundry additives, suds, perfumes, etc.

Regular Cycle

Provides normal agitation and normal spin speeds to wash cottons and heavily soiled items. For maximum cleaning, set the dial at Extra Heavy.
End of Cycle Signal (select models)
The End of Cycle Signal will sound once the cycle is completed. The End of Cycle Signal can be canceled by setting the switch to Off.

Wrinkle Control Cycle

Provides normal agitation and slow spin speed to protect wrinkle control fabrics.

Delicates Cycle

Provides slow agitation speed and slow spin speed for delicates and knits.
Pull Control Dial Out to Start
You may stop the washer at any time by simply pushing the control dial in. Therefore, it is possible to obtain a non-agitated soak or to shorten, skip or repeat any part of a cycle. The control dial must be pushed in (off position) when you change the setting.
Note: Do not attempt to turn the control dial
counterclockwise. Damage to the timer will result.
Using the Controls 4 Speed Select Models
Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation. On select models, the Infinite Water Level control allows you to select a specific setting or anywhere in between. It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust the water level, turn the control to reset and then back to the desired setting. WATER LEVEL SETTING

Mini Small Medium Large Super

LOAD SIZE

1/4 Full 1/4 - 1/3 1/3 1/2 1/2 2/3 3/4 Full WASH/RINSE TEMPS LOAD TYPE
Your washer gives you a choice of hot, warm or cold water for washing and cold or warm water (select models) for rinsing. WASH/RINSE TEMPS Hot/Cold Warm/Warm (select models) Warm/Cold Cold/Cold LOAD TYPE White and heavily soiled, color-fast items. Moderately soiled, colored items. Moderately soiled, colored items; most wrinkle-free items. Brightly colored, lightly soiled items; washable woolens.
These settings feature Automatic Temperature Control: Saves energy by adding cold water ATC Hot/Cold, to the hot water from your water ATC Warm/Cold ATC Warm/Warm heater. Provides optimum cleaning at lower temperatures. May add hot water to the incoming cold water as the washer fills. This ATC Cold/Cold assures that the water will be warm enough to properly activate detergent.

Select Wash/Spin Speed

Your washer has selectable wash and spin speed combinations. WASH/SPIN SPEED LOAD TYPE
Sturdy fabrics needing maximum Regular water extraction like jeans, towels Normal/Fast and bedding Sturdy fabrics needing a slower spin Wrinkle Control speed to reduce wrinkling, such as Normal/Slow dress shirts and dress pants Delicate fabrics needing slower spin Delicate speed because of clothing Gentle/Slow construction Handwash Intermittent slow agitation and soak Ex. Gentle/Slow to gently wash the most delicate items
Automatic Temperature Control (A.T.C.) (select models) provides the optimal wash water temperature for cleaning. To save energy, this washer will regulate wash water temperatures by mixing hot and cold water to reach the proper water temperature.
detergents do not dissolve well or clean well. 7
To select a cycle, push the control dial in (off position) and turn it to the right (clockwise) until the pointer is at the soil level needed for the wash load. Important: For optimum fabric care, the appropriate wash and spin speed for the load type must be selected using the wash/spin speed knob.

When the knob is in the On position, an additional rinse at the end of the Regular, Wrinkle Control and Delicates cycles is provided to more completely remove laundry additives, suds, perfumes, etc.
The end of cycle signal will sound once the cycle is completed. The end of cycle signal can be canceled by setting the switch to Off.
This cycle provides up to 16 minutes of agitation. Select the Regular Wash/Spin Speed setting.

Wrinkle Control

This cycle is designed for sturdy fabrics needing a slower spin speed to reduce wrinkling, such as dress shirts and dress pants. Select the Wrinkle Control Wash/Spin Speed setting.
You may stop the washer at any time by simply pushing the control dial in. Therefore it is possible to obtain a non-agitated soak or to shorten, skip or repeat any part of a cycle. The control dial must be pushed in (off position) when you change the setting.
Delicates is designed for items requiring delicate wash action. Select the Delicates Wash/Spin Speed setting. When washing delicate fabrics labeled hand wash, select the Handwash Wash/Spin Speed setting. This setting provides intermittent slow agitation and soak with a slow spin.
Soak Only (select models)
Provides 4 minutes of agitation, then soak. Avoid extended soaking soak for 30 minutes or less. The control dial must be manually advanced to a spin setting to spin and drain the water.
Using the Controls Electronic Control Models

Getting Started

1. 2. 3. 4. 5. 6. Add detergent and additives to the washer. Load the washer. Close the lid. Select the appropriate cycle and options for the load. Press the Cycle Selector dial. The Fill indicator light will illuminate and the washer will start to fill.
Note: The lid must be completely closed in order
to operate the washer controls.
Determine the selected setting based on clothes load size. Selection should provide sufficient water to permit clothes to circulate freely during agitation. It may become necessary, due to bulky fabrics, to adjust the water level after agitation begins. To adjust the water level, turn the Infinite Water Level control to reset and then back to the desired setting. WATER LEVEL SETTING Mini Small Medium Large Super LOAD SIZE 1/4 Full 1/4 - 1/3 1/3 1/2 1/2 2/3 3/4 Full WASH/RINSE TEMPS Hot/Cold (select models) Warm/Warm (select models) Warm/Cold (select models) Cold/Cold LOAD TYPE White and heavily soiled, color-fast items. Moderately soiled, colored items. Moderately soiled, colored items; most wrinkle-free items. Brightly colored, lightly soiled items; washable woolens.

Automatic Temperature Control (A.T.C.) provides the optimal wash water temperature for cleaning. To save energy, this washer will regulate wash water temperatures by mixing hot and cold water to reach the proper water temperature. WASH/RINSE TEMPS LOAD TYPE
These settings feature Automatic Temperature Control:
Your washer gives you a choice of hot, warm or cold water for washing and cold water or warm water (select models) for rinsing. Use the chart as a guide.
Saves energy by adding cold water ATC Hot/Cold, to the hot water from your water ATC Warm/Cold ATC Warm/Warm heater. Provides optimum cleaning (select models) at lower temperatures. May add hot water to the incoming cold water as the washer fills. This ATC Cold/Cold assures that the water will be warm enough to properly activate detergent.

Soil Selection

Your washer has selectable soil level settings. SOIL SELECTION Light Normal LOAD TYPE Use for cleaning lightly soiled loads. Use for cleaning moderately soiled loads. This setting will be appropriate for most loads. Use for cleaning heavily soiled loads. Use for cleaning stained, heavily soiled sturdy loads.

Fabric Selection

Select the appropriate fabric cycle for the type of load by turning the cycle selector dial until the indicator light by the desired fabric selection is illuminated. WASH/SPIN SPEED Quick Wash Gentle/Fast Hand Wash Ex. Gentle/Slow FABRIC SELECTION

Heavy Extra Heavy

For lightly soiled or wrinkled garments needed quickly. Provides intermittent agitation and soak. For wool, silk, and other hand-wash-only fabrics. Delicates For sheer fabrics, bras and lingerie Gentle/Slow needing slower agitation and spin speeds because of clothing construction. Wrinkle Control For wash and wear and synthetic Medium/Slow fabrics and lightly to normally soiled garments needing a slower spin speed to reduce wrinkling. Regular For most sturdy fabrics including Medium/Fast cottons, linens and normally soiled garments needing maximum water extraction.

STEP 5 STEP

When the knob is in the On position, an additional rinse at the end of all cycles is provided to more completely remove laundry additives, suds, perfumes, etc.
Provides approximately 33 minutes of alternating periods of soaking with brief agitation at slow speed. At the end of the cycle, the Cycle Selector dial must be manually set to a wash cycle or spin cycle to drain the washer. Avoid extended soaking.

Select Options

Spin Only

Provides a spin to remove more water from the load.

End of Cycle Signal

The end of cycle signal will sound once the cycle is completed. On select models, the end of cycle signal can be canceled by setting the switch to Off.

Rinse and Spin

Use for loads that need rinsing only or to add rinseadded fabric softener to a load.

Power Off

To cancel the cycle and turn off the washer, turn the Cycle Selector dial to Power Off and push the dial in.

Start the Washer

To start the washer, press the cycle selector dial.

Changing a Cycle

If an incorrect cycle has been accidentally selected: 1. Press the cycle selector dial. 2. Turn the cycle selector dial to the desired cycle. 3. Set the desired options for the cycle. 4. Press the cycle selector dial. The Wash indicator lights stop flashing and the new cycle starts.

Canceling a Cycle

To cancel a cycle: 1. Press the cycle selector dial. 2. Turn the cycle selector dial to Power Off and push the dial in. To drain the washer: 1. Select the Rinse and Spin or Spin Only cycle. 2. Press the cycle selector dial. The Spin light illuminates and the washer starts the rinse or spin.

Special Features

Liquid Bleach Dispenser
The dispenser automatically dilutes liquid chlorine bleach before it reaches your wash load. To use, follow these steps: 1. Measure liquid chlorine bleach carefully, following the instructions on the bottle. 2. Pour liquid chlorine bleach into bleach dispenser before adding the load. Avoid splashing or over-filling the dispenser.
Fabric Softener Dispenser
The dispenser automatically releases liquid fabric softener at the proper time during the cycle. To use, follow these steps: 1. Pour a measured amount of fabric softener into the dispenser to fill line only. 2. If fabric softener comes below line, add warm water. If it is necessary to clean the dispenser: 1. Pull the dispenser off of the top of the agitator. 2. Soak for one hour in sink or container in hot water and dishwashing liquid. 3. Hold hands over top and bottom of dispenser and shake to loosen buildup. 4. Rinse with clean, hot water. 5. Repeat process if necessary. 6. Replace dispenser on agitator. Do not use dishwashing liquid inside the washer. Oversudsing can occur.

Notes:

Never pour undiluted liquid chlorine bleach directly onto the load or into the wash tub. It is a powerful chemical and can cause fabric damage, such as tearing or color loss, if not used properly. If you prefer to use color-safe, non-chlorine bleach, pour it into the wash tub with your detergent. Do not pour non-chlorine bleaches into the bleach dispenser.
Automatic Lint Filtering System
The Lint Filtering System does not require cleaning. Wash and rinse water is filtered and re-filtered continuously to trap lint shed by most fabrics during the agitation cycle before it can be redeposited on the wash load. The engineered hole design on the wash basket in conjunction with water flow produced by the agitator, traps lint away from the clothes between the inner wash basket and the outer tub. Lint is automatically flushed from the washer during the spin cycle.
Finger Faucet (select models)
Provides a flow of water when holding the switch in the On position.

Safety Spin

If for any reason you open the washer lid when the washer is in a spin or extract period, the operation will immediately stop. This is for your personal safety. If your washer does not stop, call your service technician immediately. When the lid is closed, the operation will automatically resume.
Unbalanced Spin Load Compensator
Your new washer is designed to handle out-of-balance loads without shutting down or interrupting the washing cycle. For this reason, the cycle will always be completed. If heavier fabrics in such out-of-balance loads should ever contain excessive moisture at the completion of the cycle, redistribute the clothes in the washer and reset the control dial for the final spin period.

Overload Protector

A built-in protector automatically shuts off the washer motor in case of an overload. This can occur if: The load being washed is too heavy. Too many appliances are plugged into the line operating your washer. A low voltage condition exists on the line. Lid is opened and closed repeatedly. The overload protector permits the washer to start again when the motor has cooled to a safe operating temperature. If the motor stops repeatedly, call your service technician.

Care & Cleaning

1. After washing, leave the lid open until the interior is dry. 2. Check hoses to be sure there are no kinks or knots. 3. Your washer should not be installed where temperatures will go below freezing, as damage to the washer could result. 4. To clean, occasionally wipe exterior with a clean damp sponge or cloth. Do not use polish on plastic parts. 5. Lifetime lubrication is done at the factory, so your washer never needs to be oiled or greased. 6. Do not lay heavy or sharp objects on top of your washer. 7. The top of the washer should not be used for removing stains from garments. Some stain removers, such as rust remover, will mar the finish. 8. Remove pins, buckles or other sharp objects from clothes to prevent scratching interior parts. 9. Clothes should not be stored in washer. 10. Bleach, detergent, solvents, etc. spilled on the top of your washer that are allowed to remain will remove the glossy finish. Remove all spills with a damp, soft cloth. 11. If you close your home for the winter, have a service technician drain the washer. Unplug cord from electrical outlet and disconnect hoses from faucets.

Cleaning the Interior

Clean the interior of the washer periodically to remove any dirt, soil, odor, mold, mildew or bacteria residue that may remain in the washer as a result of washing clothes. We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior. The frequency with which the washer should be cleaned and freshened depends on factors such as usage, the amount of dirt, soil or bacteria being run through your washer, or the use of cold water. Failure to follow these instructions may result in unsatisfactory conditions, including unpleasant odor and/or permanent stains on the washer or washload. To clean and freshen the washer interior: 1. Add a measured amount of chlorine bleach to the bleach dispenser, following package directions. 2. Add 1/4 cup of detergent to the tub. 3. Run the washer without a load through a complete cycle using hot water. 4. Repeat the process if necessary.

Troubleshooting

Wont Fill Plug cord into live electrical outlet. Check fuse or reset circuit breaker. Turn the control dial to proper cycle and restart the washer. Turn both faucets on fully. Straighten inlet hoses. Disconnect hoses and clean screens. Hose filter screens may be plugged. Check fuse or reset circuit breaker. Make sure the lid is completely closed. Turn the control dial to proper cycle and restart the washer. Pauses are normal. Wait and see if the washer will start again.

Wont Agitate

Wont Spin or Drain
Check fuse or reset circuit breaker. Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for drain service. Close lid and restart the washer. For your safety, washer will not spin unless the lid is closed. Suds lock caused by too much suds. Rewash without detergent. Use correct amount of a low-sudsing detergent. Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for leveling. Be sure water level is acceptable for load size. A normal spin speed is recommended for heavy loads like jeans or towels. Plug cord into live electrical outlet. Check fuse or reset circuit breaker. Close lid and restart the washer. For your safety, washer will not agitate or spin unless lid is closed. This may be a pause in the cycle. Wait briefly and it may start. Make sure hose connections are tight. Make sure end of drain hose is correctly inserted and secured to drain facility. Avoid extended soaking soak for 30 minutes or less. Avoid overloading.

Load is Wet

Leaks Water

Is Noisy

Be sure washer is leveled properly as outlined in installation manual. Weak floors can cause vibration and walking. Operating sounds will vary depending on agitation speed. Turn both faucets on fully. If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and not between settings. Make sure temperature selection is correct. While the washer is filling, you may notice just hot and/or just cold water entering the tub when cold or warm wash temperatures are selected. This is a normal function of the Automatic Temperature Control (select models) feature as the washer determines the temperature of the water. If Auto Temperature Control (select models) is selected, cold water may feel warmer than cold water from the tap. Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is regulated correctly. Flush water line before filling washer. Check the water heater. It should be set to deliver a minimum 120 F (49 C) hot water at the tap. Also check water heater capacity and recovery rate. Disconnect hoses and clean screens. Hose filter screens may be plugged. Extra Rinse (select models) is selected.
Fills with the Wrong Temperature Water
Cycle Selector Advances Through Off
For further assistance, call Maytag Customer Assistance toll-free at 1-800-688-9900 USA or 1-800-688-2002 Canada. U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

Service & Warranty

Washer Warranty

Full One-Year Warranty

For one (1) year from the date of original retail purchase, any part which fails in normal home use will be repaired or replaced free of charge.
What is Not Covered By These Warranties:
1. Conditions and damages resulting from any of the following: a. Improper installation, delivery, or maintenance. b. Any repair, modification, alteration, or adjustment not authorized by the manufacturer or an authorized servicer. c. Misuse, abuse, accidents, unreasonable use, or acts of God. d. Incorrect electric current, voltage, electrical and/or gas supply. e. Improper setting of any control. 2. Warranties are void if the original serial numbers have been removed, altered or cannot be readily determined. 3. Light Bulbs. 4. Products purchased for commercial or industrial use. 5. The cost of service or service call to: a. Correct installation errors. b. Instruct the user on the proper use of the product. c. Transport the appliance to the servicer and back. 6. Consequential or incidental damages sustained by any person as a result of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.

Limited Warranty

After the first year from date of original retail purchase, through the time periods listed below, the parts designated below which fail in normal home use will be repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage, transportation, trip charge and diagnostic charge, if required. Second Year All parts. Third Through Fifth Year All parts of the transmission assembly. Third Through Lifetime The inner wash basket. Additional Limited Warranty Against RustThrough Should an exterior cabinet, including the top and lid, rust through during the one-year period starting from the date of retail purchase, repair or replacement will be made free of charge. After the first and through the fifth year, repair or replacement will be made free of charge for the part itself, with the owner paying all other costs, including labor, mileage, transportation, trip charge and diagnostic charge, if required. Please Note: This full warranty and the limited warranty apply when the appliance is located in the United States or Canada. Appliances located elsewhere are covered by the limited warranty only, including parts which fail during the first two years.

If You Need Service

First see the Troubleshooting section in your Use and Care Guide or call Customer Service at 1-800-688-9900 USA or 1-800-688-2002 Canada.
To Obtain Warranty Service
To locate an authorized service company in your area contact the Maytag dealer from whom your appliance was purchased or call Maytag ServicesSM, Customer Assistance. Should you not receive satisfactory warranty service, please call or write: Maytag ServicesSM Attn: CAIR Center P.O. Box 2370, Cleveland, TN 37320-2370 U.S.A. 1-800-688-9900 Canada 1-800-688-2002 U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

Canadian Residents

This warranty covers only those appliances installed in Canada that have been listed with the Canadian Standards Association unless the appliances are brought into Canada due to transfer of residence from the United States to Canada. The specific warranties expressed above are the ONLY warranties provided by the manufacturer. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Note: When contacting Maytag ServicesSM, Customer Assistance
about a service problem, please include the following: a. Your name, address and telephone number. b. Model number and serial number (found on the back center of the control panel) of your appliance. c. Name and address of your dealer and the date the appliance was purchased. d. A clear description of the problem you are having. e. Proof of purchase.

Use & Care Guides, service manuals and parts information are available from Maytag ServicesSM, Maytag Customer Assistance. MAYTAG 403 W. 4th Street N. P.O. Box 39 Newton, Iowa 50208

Oversized Capacity Plus Washer MAV-4

TABLE OF CONTENTS

Welcome. Inside Cover Safety Instructions.. 1 Controls At A Glance. 2-3 Operating Tips.. 4-Day Detergent Dispenser. 6-7 Care and Cleaning. 7 Storing the Washer.. 7 Before You Call. 8-9 Warranty. Back Page
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
Models: MAV6000 MAV6057 MAV7000

Welcome

Welcome and congratulations on your purchase of a Maytag clothes washer. Your complete satisfaction is very important to us. Read this guide for best results. It contains instructions to acquaint you with proper operating and maintenance procedures. In addition you will find a Laundering Tips guide packed with your clothes washer. It contains information on recommended laundering procedures, stain removal and special laundering situations. Save time and money. If something should go wrong, we suggest consulting the Before You Call section in the back of this book. It is designed to help you solve basic problems before consulting a servicer. However, should you need assistance in the future, it is helpful to: 1) Have complete model and serial number identification of your washer. This is located on a data plate on the center top edge of the control panel. Record these numbers below for easy access. Model Number __ __ __ __ __ __ __ __ __ __ Serial Number __ __ __ __ __ __ __ __ __ __ 2) IMPORTANT: Keep this guide and the sales receipt in a safe place for future reference. Proof of original purchase date is needed for warranty service. Please attach your sales receipt here.
If you have questions, write us (include your model number and phone number) or call: Maytag Appliances Sales Company Attn: CAIRSM Center P.O. Box 2370 Cleveland, TN 37320-2370 1-800-688-9900 USA 1-800-688-2002 CANADA 1-800-688-2080 USA TTY (for deaf, hearing impaired or speech impaired) (Mon.Fri., 8am8pm Eastern Time) Internet: http://www.maytag.com For service and warranty information, see back page.
NOTE: In our continuing effort to improve the quality of our appliances, it may be necessary to make changes to the appliance without revising this guide.
Important Safety Instructions
WARNING To reduce the risk of fire, explosion, electric shock, property damage or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using the appliance. 2. As with any equipment using electricity and having moving parts, there are potential hazards. To use this appliance safely, the operator should become familiar with the instructions for operation of the appliance and always exercise care when using it. 3. Do not install or store this appliance where it will be exposed to the weather. 4. Install and level washer on a floor that can support the weight. 5. This appliance must be properly grounded. Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local and national codes. See installation instructions for grounding this appliance. 6. To avoid the possibility of fire or explosion: a. Do not wash items that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode. Hand wash and line dry any items containing these substances. Any material on which you have used a cleaning solvent, or which is saturated with flammable liquids or solids, should not be placed in the washer until all traces of these liquids or solids and their fumes have been removed. These items include acetone, denatured alcohol, gasoline, kerosene, some liquid household cleaners, some spot removers, turpentine, waxes and wax removers. b. Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode. c. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using a washing machine or combination washer-dryer, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time. 7. Do not reach into the appliance if the agitator is moving. 8. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 9. Do not tamper with controls. 10. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in published user-repair instructions that you understand and have the skills to carry out. 11. Unplug power supply cord before attempting to service your washer. 12. The agitator should not be removed. If the agitator is removed, it must be replaced by pushing down completely and the locking screw tightened before the washer is operated. 13. Store laundry aids and other material in a cool, dry place where children cannot reach them. 14. Do not wash or dry items that are soiled with vegetable or cooking oil. These items may contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself. 15. Do not use chlorine bleach and ammonia or acids (such as vinegar or rust remover) in the same wash. Hazardous fumes can form. 16. Do not machine wash fiberglass materials. Small particles can stick to fabrics washed in following loads and cause skin irritation. 17. Before the appliance is removed from service or discarded, remove the door to the washing compartment.

Save These Instructions

Controls At A Glance

Select Cycle

Press the control dial in and turn clockwise to the desired cycle. Pull the dial out to start the washer.
NOTE: HEAVY and NORMAL settings on all cycles will change agitation speeds during the wash time. You may hear this change in speed. This is normal.
WHITES is designed to clean underwear, T-shirts and other cotton sturdy items like towels, sheets, jeans etc. HEAVY: 21 minutes of wash time. NORMAL: 15 minutes of wash time. LIGHT: 9 minutes of wash time.
COLORS is designed to clean colored items as well as dress shirts, dress pants, business casual and poly/cotton to reduce wrinkling. PRESOAK (select model): provides a total of 33 minutes wash time. The first 12 minutes are periods of agitation and soak followed by 21 minutes of agitation. Presoak automatically advances through the wash cycle. HEAVY: 18 minutes of wash time. NORMAL: 12 minutes of wash time. LIGHT: 9 minutes of wash.
DELICATES is designed to clean items requiring a gentle wash action. This would include blouses, nylons, lingerie and dress shirts. NORMAL: 15 minutes of wash and soak cleaning action. LIGHT: 9 minutes of wash and soak cleaning action.

Select Water Level

LOAD SIZE
Simply move the slide lever up or down to the desired setting. Select models have an infinite slide lever that can be set anywhere from Super to Mini. If more water is needed once the fill is complete, move the lever up to reset and then to the proper setting.
REMEMBER: Items must circulate freely for best results.
3/4 Full 1/2 3/4 Full 1/3 1/2 Full 1/4 Full

Select Water Temperature

LOAD TYPE
Press the appropriate button to select the wash and rinse temperatures. Follow the garment care label for best results. Use the chart at the right as a guide.
White and heavily soiled, color-fast items Delicate or colorfast items
REMEMBER: In wash water temperatures below 65 F, detergents do not dissolve well or clean well. Care labels define cold water as up to 85 F.
Moderately soiled, colored items; most wrinkle free items Brightly colored, lightly soiled items; washable woolens
Select A Customized Cycle
Press the appropriate button(s) to select one or more options.

Super Wash

Can be used with any wash cycle to clean very heavily soiled items. Provides fast agitation throughout the WHITES and COLORS cycles. Provides fast agitation for approximately 3 minutes at the beginning of the DELICATES cycle. Provides an additional rinse at the end of the cycle to more completely remove laundry additives, suds, perfume, etc. Assures a cold water wash of 75 F and warm water wash of 95 F. This option assures detergent will dissolve and provide optimum cleaning results. Press this button to cancel and reset any of the above options.
Extra Rinse OR Second Rinse (select models) Auto Temperature Control Cancel

If Auto Temperature Control is selected with a Warm/Warm, Warm/Cold, or Cold/Cold water temperature setting, the light will illuminate during the wash.

Start Washer

Add detergent. Add load and close lid. Pull the control dial out to start.

Operating Tips

Chlorine Bleach Dispenser
The dispenser automatically dilutes liquid chlorine bleach before it reaches your wash load. To use, follow these steps: 1. Measure liquid chlorine bleach carefully, following the instructions on the bottle. 2. Add the bleach to the dispenser before adding the load. Avoid splashing or over-filling the dispenser. NOTE: Never pour undiluted liquid chlorine bleach directly onto the load or into the wash tub. It is a powerful chemical and can cause fabric damage, such as tearing or color loss, if not used properly. If you prefer to use color-safe, non-chlorine bleach, pour it into the wash tub with your detergent. Do not pour non-chlorine bleaches into the bleach dispenser.
Fabric Softener Dispenser
This dispenser automatically releases liquid fabric softener at the proper time during the cycle. To use, follow these steps: 1. Pour liquid fabric softener into the dispenser using the amount recommended on the package. 2. Add warm water to the dispenser until it reaches the MAX line. NOTE: Do not stop the washer during the first spin. This will cause the dispenser to empty too soon. Never pour fabric softener directly on the load. It will leave spots and stains. Use the dispenser for liquid fabric softeners only. Clean the area in and around the dispenser frequently with hot water, detergent and a soft brush.
Pour liquid chlorine bleach into bleach dispenser.
Pour liquid fabric softener into cup and dilute with warm water.
For detailed information on sorting, pretreating stains, etc., see the enclosed Laundry Tips pamphlet.

Detergent

Use either liquid or granular laundry detergent. For best results, be sure detergent is added to the washer BEFORE the load and be sure wash water is above 65 F. Use the correct amount of detergent for the load size, soil level and water conditions. Use more detergent if you have hard water and very soiled loads. If you have soft water or a lightly soiled load, use less detergent. (See manufacturers instructions.) Wipe up any detergent spills on the washer.

Loading

Put dry, unfolded clothes loosely in the tub, up to the top row of holes for a maximum load. Do not wrap large items like sheets around the agitator. Mix large and small items for best circulation. Wash bulky items like blankets separately. When laundering wrinkle free items or items of delicate construction, washable woolens or loosely knit items, never use less than the MEDIUM water level setting. This will minimize shrinkage, wrinkling and pulling of seams. For best results, add the detergent to washtub before adding the load.

Using the 30 Day Detergent Dispenser

(select models)

Filling Dispenser
1) Unscrew the dispenser fill cap (figure 1). 2) Pour in your favorite liquid detergent, up to 100 fluid ounces at one time. 3) Replace the dispenser fill cap. 4) Close the washer lid. 5) Open the washer lid. 6) Move the slide indicator all the way to the top (figure 1). Next, follow steps 7 and 8 to set the amount of detergent used for the average load. Note: Steps 7 and 8 only need to be done ONCE when first filling the dispenser or changing brands of detergent. 7) Place the cap of your detergent bottle under the PUSH button. Fill the cap with detergent from the dispenser as full as you would for most of your loads by pressing and holding the PUSH button (figure 2). Place the detergent from the cap either in the tub or back in the dispenser by removing the dispenser fill cap. 8) Move the slide indicator to the level of the liquid in the sight glass (figure 3). For your next load of laundry, just press and hold the PUSH button until the detergent moves down to the slide indicator to dispense detergent directly into the tub. 9) The sight glass on the right side shows how much detergent remains in the dispenser. Refill the dispenser when the detergent level nears the bottom of the refill indicator window.

Figure 2

Figure 1
Note: If you decide to change brands of liquid detergent (Example: Tide to Wisk or Tide with Bleach Alternative to Tide) it is important the dispenser be empty and clean before adding new detergent (see page 7). Different detergents may interact and clog the dispenser.

Figure 3

To Remove the Dispenser for Cleaning
1) Support the bottom of the dispenser with one hand. Use a quarter and turn four slotted screws counter clockwise 1/4 turn (figure 1). 2) Pull the dispenser out from the bottom of the lid. 3) Remove fill cap. 4) Fill with water about half way. Move the dispenser from side to side to wash out detergent. 5) With the dispenser over a large sink or bath tub, turn it upside down to empty the water/detergent out of the dispenser fill area.

To Replace the Dispenser

1) Place the top of the dispenser in the top lip of the lid. 2) Push the bottom of the dispenser into the bottom of the lid. 3) While supporting the bottom, use a quarter and turn each of the four screws 1/4 turn clockwise to lock the dispenser into place. 4) Close the washer lid. 5) Open the washer lid. 6) Press the PUSH button to release any remaining water/detergent. Repeat steps 46 until no more water can be drained from the dispenser. It is normal for a small amount of water to remain in the dispenser after cleaning. 7) Refill the dispenser with your favorite detergent (see page 6).

Care and Cleaning

Turn off the water faucets after finishing the days washing. This will shut off the water supply to the washer and prevent the unlikely possibility of damage from escaping water. Use a soft cloth to wipe up all detergent, bleach or other spills as they occur. Clean the following as recommended: Control Panel clean with a soft, damp cloth and glass cleaner. Do not use abrasive powders or cleaning pads. Cabinet clean with soap and water. Interior hard water deposits may be removed, if needed, using a recommended cleaner labeled washer safe.

Storing the Washer

Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare the washer for storage as follows: Select NORMAL on the WHITES cycle and add one cup of bleach or white vinegar to a full load of water without clothes. Run the washer through a complete cycle. Turn the water faucets off and disconnect the inlet hoses. Advance the cycle control dial to Spin and lower the drain hose to eliminate any water that may be in the drain hose. Disconnect the washer from the electrical supply and leave the washer lid open to let air circulate inside the tub.

Before You Call

For problem laundry solutions (i.e. fabric damage, residue, tangling) and special laundry care procedures, see the enclosed Laundry Tips pamphlet.
Check these points if your washer. Always Check First
Plug cord into live electrical outlet. Check fuse or reset circuit breaker.

Wont Fill

Turn the control dial to proper cycle and pull dial out to start the washer. If equipped with buttons, be sure they are fully depressed. Turn both faucets on fully. Straighten inlet hoses. Disconnect hoses and clean screens. Hose filter screens may be plugged.

Wont Agitate

Turn the control dial to proper cycle and pull dial out to start the washer. If equipped with buttons, be sure they are fully depressed. Close lid and pull dial out to start the washer. For your safety, washer will not agitate or spin unless the lid is closed. The washer is equipped with a lid switch failure detector. If the lid switch should malfunction, the detector will stop operations for your safety. Call for service. Pauses are normal. Wait and see if the washer will start again.

Wont Spin or Drain

Straighten drain hoses. Eliminate kinked hoses. If there is a drain restriction, call for service. Close lid and pull dial out to start the washer. For your safety, washer will not agitate or spin unless the lid is closed. The washer is equipped with a lid switch failure detector. If the lid switch should malfunction, the detector will stop operations for your safety. Call for service.

Check these points if your washer. Turn the control dial to proper cycle and pull dial out to start the washer. If equipped with buttons, be sure they are fully depressed. Close lid and pull dial out to start the washer. For your safety, washer will not agitate or spin unless lid is closed. This may be a pause or soak period in the cycle. Wait briefly and it may start. The washer is equipped with a lid switch failure detector. If the lid switch should malfunction, the detector will stop fill operations for your safety. Call for service.

Leaks Water

Make sure hose connections are tight. Make sure end of drain hose is correctly inserted and secured to drain facility. Avoid extended soaking soak for 30 minutes or less. Avoid overloading.

Is Noisy

Be sure washer is leveled properly as outlined in installation manual. Weak floors can cause vibration and walking. Be sure rubber feet are installed on leveling legs.
Fills with the Wrong Temperature Water
Turn both faucets on fully. If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and not between settings. Make sure temperature selection is correct. If Auto Temperature Control is selected, cold water may feel warmer than cold water from the tap (see page 3). Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is regulated correctly. Flush water line before filling washer. Check the water heater. It should be set to deliver a minimum 120F (49C) hot water at the tap. Also check water heater capacity and recovery rate. Disconnect hoses and clean screens. Hose filter screens may be plugged.
Cycle Selector Dial Advances Through OFF
For further assistance contact Maytag Appliances Sales Company, Maytag Customer Assistance: U.S. 1-800-688-9900 or Canada 1-800-688-2002 U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080.

Maytag Washer Warranty

Full One Year Warranty For one (1) year from the date of original retail purchase, any part which fails in normal home use will be repaired or replaced free of charge. Limited Warranty After the first year from date of original retail purchase, through the time periods listed below, the parts designated below which fail in normal home use will be repaired or replaced free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation. Second Year All parts. Third through Fifth Year The drive motor. All parts of the solid state controls (if so equipped). Third through Tenth Year All parts of the transmission assembly. Third through Lifetime The inner wash basket. Additional Limited Warranty Against Rust-Through Should an exterior cabinet, including the top, lid and baseframe, rust through during the one year period starting from the date of retail purchase, repair or replacement will be made free of charge. After the first and through the tenth year, repair or replacement will be made free of charge for the part itself, with the owner paying all other costs, including labor, mileage and transportation. Please Note: This full warranty and the limited warranty apply when the washer is located in the United States or Canada. Washers located elsewhere are covered by the limited warranty only, including parts which fail during the first two years. Canadian Residents This warranty covers only those appliances installed in Canada that have been listed with the Canadian Standards Association unless the appliances are brought into Canada due to transfer of residence from the United States to Canada. The specific warranties expressed above are the ONLY warranties provided by the manufacturer. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

To Receive Warranty Service
To locate an authorized service company in your area contact the Maytag dealer from whom your appliance was purchased; or call Maytag Appliances Sales Company, Maytag Customer Assistance at the number listed below. Should you not receive satisfactory warranty service, please call or write: Maytag Appliances Sales Company Attn: CAIRSM Center P.O. Box 2370 Cleveland, TN 37320-2370 U.S. 1-800-688-9900 Canada 1-800-688-2002 U.S. customers using TTY for deaf, hearing impaired or speech impaired, call 1-800-688-2080. When contacting Maytag Appliances Sales Company, Maytag Customer Assistance about a service problem, please include the following: (a) Your name, address and telephone number; (b) Model number and serial number (found on the back center of the control panel) of your appliance; (c) Name and address of your dealer and the date the appliance was purchased; (d) A clear description of the problem you are having. (e) Proof of purchase.
What is not covered by these warranties:
1. Conditions and damages resulting from any of the following: a. Improper installation, delivery, or maintenance. b. Any repair, modification, alteration or adjustment not authorized by the manufacturer or an authorized servicer. c. Misuse, abuse, accidents, or unreasonable use. d. Incorrect electric current, voltage or supply. e. Improper setting of any control. 2. Warranties are void if the original serial numbers have been removed, altered, or cannot be readily determined. 3. Products purchased for commercial or industrial use. 4. The cost of service or service call to: a. Correct installation errors. b. Instruct the user on proper use of the product. c. Transport the appliance to the servicer. 5. Consequential or incidental damages sustained by any person as a result of any breach of these warranties. Some states do not allow the exclusion or limitation of consequential or incidental damages, so the above exclusion may not apply.
Users Guides, service manuals and parts catalogs are available from Maytag Appliances Sales Company, Maytag Customer Assistance.
MAYTAG One Dependability Square Newton, Iowa 50208
Form No. 557CMA Part No. JN Litho U.S.A.