www.ersatzteil-service.de

REPAIR PARTS MANUAL

MODEL NO. MC1292RB (MC1292RBA) Lawn Tractor
79-46 10.23.03 TR PRINTED IN U.S.A.
Ihr Ersatzteilspezialist im Internet

HOW TO USE THIS MANUAL

This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them. Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat. When ordering parts, always give the following information: Product - Tractor Model Number - MC1292RB (MC1292RBA) Part Number Part Description

TABLE OF CONTENTS

SCHEMATIC.... 3 ELECTRICAL...4-5 CHASSIS....6-7 DRIVE....8-9 STEERING...10-11 SEAT.... 12 DECALS.... 13 ENGINE.....14-15 MOWER LIFT....16-17 MOWER DECK....18-19 BAGGER....20-21
TRACTOR- -MODEL NO. MC1292RB (MC1292RBA), PRODUCT NO. 28-01

SCHEMATIC

AMMETER (OPTIONAL)

BATTERY

RED RED

STARTER SOLENOID

STARTER M

BL K AC

M A1 L A2

BLACK BLACK

CLUTCH / BRAKE (PEDAL UP)

FBI BUZZER

ATT'MENT CLUTCH (CLUTCH OFF)

OPERATOR PRESENCE RELAY

FBI SWITCH

ORANGE

SEAT SWITCH (NOT OCCUPIED)

30 87A

BAGGER INTERLOCK (NO BAG, CHUTE OR PLUG)

BAGGER RELAY 30 86

87A MOWER ENGAGED RELAY
FUEL LINE SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES)
28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)

IGNITION UNIT

CARBURETOR SOLENOID (IF SO EQUIPPED)
CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM
LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM

ALTERNATOR

14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)

IGNITION SWITCH

POSITION CIRCUIT MAKE NONE A2+L NONE NONE
NON-REMOVABLE CONNECTIONS HEADLIGHTS
NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST.

87A 85 30

OFF M+G+A1 RUN/LIGHT B+A1 RUN START B+A1 B + S + A1
REMOVABLE CONNECTIONS PTO SWITCH

POSITION OFF ON CIRCUIT

C + G, B + H C + F, B + E, A + D

G F C H E B

WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE REPLACED TO PROPERLY SECURE YOUR WIRING.

REPAIR PARTS

ELECTRICAL
KEY PART NO. NO. 16 34-76 04-17 61-18 37-00 41-12 47-16 59-17 51-51 04-12 77-16 07-17 55-14 04-17 97-11 04-13 15-17 88-14 08-14 19-16 94-18 03-49 06-10 97-48
DESCRIPTION Battery Bolt Hex Hd 1/4-20 unc x 3/4 Switch Interlock Push-In Harness Asm. Light Bulb Cable Starter 6 Ga. 11" Red Cable Battery Crd 56" Red Fuse 20 Amp Nut Keps Hex 1/4-20 unc Cable Ground 6 Ga. 18" Black Switch Plunger Normal Op Olive Switch Ignition Key Ign Harness Ign Bolt Flk Fin Hex 1/4-20 unc x 1/2 Cover Terminal Red Solenoid Adapter Ammeter Rectangular Protection Wire Loop Buzzer Crd Switch FBI CRD Screw Thdrol 3/8-16 x 1/2 Ty-Tt Relay Asm
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm.

CHASSIS AND ENCLOSURES

184 208
chassis-Elite_Basic_CRD_1
KEY PART NO. NO. 17 46-18 03-06 06-15 52-18 44-12 64-18 54-14 06-17 49-18 69-18 05-51 05-18 58-12 69-78 06-13 13-80 06-18 38-18 98-18 13-16 51-18 30-18 30-11 06-49 05-18 17-17 47-14 24-18 13-15 65-18 03-82
DESCRIPTION Chassis Drawbar Screw 3/8-16 x.75 Bumper Hood/Dash Saddle Clip Insulator 13/32 Mtg. Hole Dash Bolt, Carriage 3/8-16 x 3/4 Panel, Dash, L.H. Panel, Asm. Dash R.H. Screw, Machine, Truss Head 5/16-18 unc x 3/4 Nut Hood Assembly Bumper Hood Bolt Washer 13/32 x 13/16 x 12 Ga. Nut Grille Lens Asm Lens Grille Fender Bracket, Fender Support Footrest, L.H. Footrest, R.H. Bolt Screw Thdrol 5/16-18 x 1/2 TYT Bracket Asm Pivot Mower Rear Bracket Pivot Laser/Elite LT Screw Hex 1/4-1/2 Console Rod Pivot Chassis/Hood Bracket Exten Chassis Lh CRD
KEY PART NO. NO. -03-16 56-18 13-17 18-17 88-14 06-13 20-51 06-18 82-18 82-17 46-18 11-16 07-12 50-06 12-07 10-08 10-16 89-49 06-67 05-67 06-00 06-18 38-18 13-18 57-18 57-00 54-79

DESCRIPTION Bracket Exten Chassis Rh CRD Support Battery CRD Cover Battery CRD Lt Screw HWHD Hi-Lo #13-16 x 3/4 Backplate CRD Bolt Rdhd Sqnk 3/8-16 x 2-1/2 Gr. 5 Washer 13/32 x 1-1/4 x 16 Ga. Nut, Keps Hex 3/8-16 unc Trap Door CRD Rod Pivot FBI CRD Bracket Actuator Bagger CRD Knob Rod Latch Asm Multch Bagger Nut Weld.327/.304 #10-24 Washer #10 Washer Lock #10 Screw Pan Hd Phillips 10-24 x 5/8 Nut Push Screw 3/8-16 x 1/2 Screw 5/16-18 x 1/2 Screw Thdrol 3/8-16 x 1/2 Screw Hex Wsh Thdrol 3/8-16 x 3/4 Insert Lens Reective Cover Fender Rack CRD Seal RH Side Bagger Seal LH Side Bagger Plug, Button

269 51

264 171

182 183

drive-fender_CRD_Laser_9
KEY PART NO. NO. 1 ------14 66-16 59-00 00-12 15-06 05-16 56-18 03-02 04-10 57-55 04-04 04-49 05-80 05-78 06-80 06-10 69-17 56-35 06-10 68-13 13-02 04-17 57-07 16-17 49-17 55-12 01-21 16-12 49-16 59-76 06-12 49-13 13-11 10-12 77-15 44-12 32-11 06-68 06-10 57-10 57-06 06-16 56-12 48-04 07-15 47-13 70-12 17-00 00-12 35-83
DESCRIPTION Transaxle Peerless 206-546 Order parts from transaxle manufacturer Spring Brake Return Pulley Transaxle Ring Retainer #5100-62 Strap torque 30 degrees Screw 5/16-18 x 3/4 Rod Shift Fender Adjust Lt Clutch Asm Noram Pin, Cotter 1/8 x 1 Washer Plate Shf.3888 sq hole Bolt 1/4-28 unf Gr. 8 w/patch Washer, Lock Hvy Helical Bolt Hex FGHD 5/16-18 x Gr. 5 Nut, Lock Hex w/Ins 5/16-18 unc Bolt Hex 3/8-16 unc x 1 Gr. 5 Nut, Lock Hex w/Wsh 3/8-16 unc Knob Round 1/2-13 unc Blk Rod, Brake CRD Main Nut Spring, Rod, Brake Washer 13/32 x 13/16 x 16 Ga. Pin, Cotter 1/8 x 3/4 Rod, Parking Brake Cap, Parking Brake Bracket, Mfg. Transaxle Shaft, Asm Pedal Foot CRD Bearing, Nylon Washer 21/32 x 1 x 16 Ga. Pin, Roll 3/16 x 1" Pulley, Flat Bolt Fin Hex 3/8-16 unc x 2-3/4 Spacer, Split 395 x 59 Bzp Washer 13/32 x 13/16 x 12 Ga. Washer 11/32 x 5/8 x 12 Ga. Pulley, Idler, V Groove Plasitc Bellcrank Clutch Grnd Drv Retainer, Belt Style Spring Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5 Nut, Crownlock 3/8-16 unc Link, Clutch 7.66 Spring, Return, Clutch Screw 3/8-16 x 1-1/4 V-Belt Kev PMST CRD Cover, Pedal Washer Keeper, Belt Engine F-Proof Spacer Axle Washer 25/32 x 1-1/4 x 16 Ga. Ring, E Key, Square

KEY NO. 269

PART NO. 17-12 50-14 50-16 57-17 12-16 56-12 47-09 12-90 06-16 58-13 32-16 60-16 55-18 39-29 20-14 04-68 04-78 04-16 56-49 05-16 55-16 54-49 06-16 56-16 59-16 59-12 09-16 56-18 02-18 26-18 60-49 06-58 05-17 07-17 56-17 56-17 50-00 06-17 56-17 80-13 14-00 06-18 19-18 20-18 20-14 06-18 24-02

DESCRIPTION Washer 25/32 x 1-5/8 x 16 Ga. Key Woodruff Arm Shift PMST 20" Tires Spring, Torsion Washer 17/32 x 3/4 x 16 Ga. Link Shift CRD Pmst 18" Tires Spring, Retainer 1 Washer 9/32 x 3/4 x 10 Ga. Nut Lock 3/8-16 Bushing, Bellcrank Grnd Dr Washer 13/32 x 2 x 10 Ga. Washer Srred 5/16 ID x 1.125 Bracket Shift Mount Hub Shift Washer 29/32 x 1-1/4 x 16 Ga. Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr. 5 Nut Crownlock 1/4-20 unc Bolt Hex Fin 1/4-20 unc x 1 Gr. 5 Bracket Pivot Lever Screw 5/16-18 x 5/8 Bracket Support Shift CRD Bolt Shoulder 5/16-18 x.561 Screw Thdrol 3/8-16 x 1/2 Ty-Tt Shaft Asm Shift Front CRD PMST Keeper Flat Idler 3.06" CRD Keeper Belt Idler 1.88" CRD Washer Sintered Pulley Flat Composite 3.06" Bracket Idler Ground Drive CRD Keeper Belt 2.5" Od V-Idler CRD Pulley V-Idler 2.50" Od CRD Screw Hexwsh Thdrol 3/8-16 x 2-3/4 Screw 5/16-18 x 1.25 Bolt Hex 7/16-20 x 5 Shaft Asm. Brake Rod Brake Secondary Bracket Cable Chassis Screw 3/8-16 x 1 Brace Shaft Brake Clip Retainer Pulley Idler Flat Plated Screw Hex Wsh THDR 3/8-16 x 3/4 Bracket Clutch Spacer Idler Chassis Shield Idler Bolt Rd Sqk 3/8-16 x 3-1/4 Guard Mufer OHV B&S RH
NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm

STEERING ASSEMBLY

steering_pl.lt_29

KEY NO. 95

PART NO. 97-18 47-16 98-16 98-12 49-12 17-00 00-17 51-04 06-94 08-13 65-14 52-18 06-00 06-17 01-11 12-04 05-54 05-15 50-15 29-14 01-18 38-54 06-18 67-16 96-12 17-18 06-12 12-54 04-13 04-16 03-11 06-17 51-16 98-16 98-17 39-17 51-17 55-18 89-67
DESCRIPTION Steering Wheel Cast Iron Axle Assembly Spindle Assembly, L.H. Spindle Assembly, R.H. Bearing, Race, Thrust, Hardened Washer 25/32 x 1-5/8 x 16 Ga. Ring, Klip Link, Drag Washer, Lock Nut Hex Jam Toplock 1/2-20 Spacer Brg Axle Front Nut, Hexange Lock Shaft Assembly, Steering Screw, 3/8-16 x 3/4 Rod, Tie Washer 11/32 x 3/4 x 16 Ga. Washer Lock Hvy Hlcl Spr 5/16 Nut Crownlock 5/16-24 unf Bushing, Steering Screw TT #I0-32 x 5 x 3/8 Flange Cap Wheel Steer Washer 9/16 x 2-3/8 x 12 Ga. Nut Crownlock 3/8-24 Adaptor, Steering Wheel Boot, Steering Dash P/L Mtl Washer 25/32 x 1-1/4 x 16 Ga. Extension Steering Cap, Spindle Nut Crownlock 1/4-28 Bolt Hex 1/4-28 unf x 1-1/4 Spacer Brace Axle Bolt Rdhd Sq 3/8-16 unc x 2-1/4 Steering Asm. Brace Axle Bracket Susp Chassis Front Washer Flat.781 x 1-1/2 x.14 Bolt Shoulder 7/16-20 unc Clip Steering Washer Hardened

SEAT ASSEMBLY

seat_lt.bolt_6
KEY PART NO. NO. 53-14 05-11 06-13 16-14 50-80 06-12 41-00 06-13 16-18 24-12 12-12 12-48
DESCRIPTION Seat Bracket Pnt Pivot Seat (blk ) Bolt Fin Hex 3/8-16 unc x 1 Washer Flat 13/32 x 1 x 10 Ga. Clip Push In Hinged Nut Lock Hex 3/8-16 unc Spring Seat Cprsn Blk Zi Screw 3/8-16 x 1-1/2 Washer 13/32 x 1 x 14 Ga. Pan Pnt Seat (blk ) Bracket Pnt Mounting Switch Bushing Snap Blk Nyl 50 Id

KEY PART NO. NO.

DESCRIPTION
05 04-12 Bolt Rdhd Sht Nk 1/4-20 x 1-1/43-00 Spacer Split 12 12-50 Spring Cprsn Plate SW 1.310 Ga. 12 39-76 Nut Lock 1/4 Lge Flg Gr. 5 Zinc 17 18-52 Bolt Shoulder 5/16-18 unc-2A 80 05-00 Nut Hex Lock w/Ins 5/16-08-14 Bolt Hex Black 17 19-12 Washer 17/32 x 1-3/16 x 12 Ga. 12 70-18 Bolt Shoulder 5/16-18 x 08-00 Washer Lock Hvy Hlcl Spr 1/2 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

DECALS

_ MAX + 90N _ MAX + 150N
KEY PART NO. NO. 14 54-18 48-18 90-18 58-18 04-18 97-14 50-18 21-15 97-37
DESCRIPTION Decal Read Owners Manual Sym Decal Hp Engine Decal Hood Decal Steering Decal Fender 100 OB/CE Decal Fender Decal Bat Dan/Poi P/L Sym Wpn Decal Mower Cut Finger Symbol Decal Brake/Clutch Symbol Lt
KEY PART NO. NO. 04-15 97-14 08-16 62-18 10-13 83-18 26-18 10-18 52-18 52-18 79-46
DESCRIPTION Decal Warn Back Plate CRD Decal Chassis Hot Mufer Decal Saddle Brake Parking Decal Hex Belt Sch 92 CRD Pad Footrest RH Decal Lift Handle Decal Bagger Frame Pad Footrest LH Manual Operator's (Euro) Manual Operator's (Scand) Manual Parts

WHEELS & TIRES

5,8 4,3,11

KEY NO. 11 --

PART NO. 91-06 51-10 62-05 99-18 33-12 49-12 49-18 33-10 62-12 49-17 50-14 43-34
DESCRIPTION Cap Value Tire Stem Value Tire F Ts 15 x - 6 Service Tube Inner Front #35060 Rim Asm 6" front Service Fitting Grease Bearing Flange Rim Asm 8" rear Service Tire R Ts 18 x 9.5-8 Service Tube Rear x 8 Service Cap Axle Blk x Sealant, Tire (10 oz. tube)

wheel_1

ENGINE
OPTIONAL EQUIPMENT Spark Arrester

engine-bs.1cyl_29

KEY PART NO. NO. 17 05-72 04-08 -------97-16 52-14 84-16 98-18 09-92 06-13 71-18 55-14 05-12 34-13 70-18 16-67 04-00 06-09 14-18 39-06 06-51 04-00
DESCRIPTION Control Throt Screw Hex Thd Cut 1/4-20 x 1/2 Engine B&S Model 21A807 (Order Parts from Engine Manufacturer) Mufer Exhaust B&S Lt Gasket Id Tin Plated Tube Drain Oil Easy Shield Browning/Debris Guard Control Choke Nut Keps 3/8-24 unf Arrestor Spark Tank Fuel 2.00 Fr Cap Asm Fule Top Vent N/Lany Clamp Hose Blk Line Fuel 20" Plug Drain Oil Easy Screw Hexwsh Thdrol 3/8-16 x 3/4 Screw 3/8-16 x 3/4 Washer 9/32 x 7/8 x 16 Ga. Screw Socket Head 5/16-18 x 1 Screw 3/8-16x1-1/4 Nut Keps Hex 1/4-20 unc

MOWER LIFT

lift-rh.1piece_3

KEY NO. 32

PART NO. 94-15 94-17 89-00 00-21 16-12 01-10 94-12 45-16 58-16 58-12 46-17 32-35 08-17 56-80 08-13 98-16 35-16 98-54 06-00
DESCRIPTION Wire Asm Inner Spring W/Plunger Shaft Asm. Lift Pin Groove E Ring #5133-62 Washer 21/32 x 1 x 21 Ga. Bearing Nylong Grip Handle Bicycle Button Plunger Black Link Asm Lift L.H. Link Asm Lift R.H. Retainer Spring Link Front Nut Jam Hex 1/2-13 unc Trunnion Blk Zinc Nut Lock w/Wsh 1/2-13 unc Arm Suspension Mower Retainer Spring Bearing, Pvt. Lift. Nut Crownlock 3/8-24

42 _c lu t ch

119 117
36(92cm)_deck-elect.(CRD)_1

KEY NO. 37 40

PART NO. 55-14 05-16 55-16 55-12 46-16 55-18 17-03 06-18 63-13 76-12 87-11 04-18 63-14 06-11 06-13 28-18 17-68 05-16 52-16 54-16 52-16 52-16 52-16 55-16 55-17 39-18 76-15 35-17 83-16 52-16 52-14 67-13 13-68 06-00
DESCRIPTION Housing Asm. Mower Bolt Rdhd Sqnk 5/16-18 unc x 3/4 Bracket Asm. S-Bar Chass Bracket Bar Sway Deck Retainer Spring Bar Sway Bolt 3/8-24 x 1.25 Gr. 8 Patched Washer Lock Hvy 3/8 Unplated Blade 3-1 Lh Shaft Asm. W/Lower Bearing Housing Mandrel Vented (Machd) Bearing Ball Mandrel Blade 3-1 Rh Bolt Carriage 3/8-16 x 1-1/4 Bolt Rdhd Sqnk 3/8-16 x 3/4 Bolt Shoulder 5/16-18 Thd Form Bolt 3/8-24 x 1.25 Gr. 8 Ptch Lhthd Nut Crown Lock 5/16-18 Bracket Idler Sprt RR Bracket Idler Sprt RF Bracket Suspension LF Bracket Suspension RF Brace Support Susp Frt CRD Bracket Asm. Susp RR Bracket Asm. Susp LR Screw Thd Rolling Washer Head Washer Spacer Mandrel Pulleys 36 & 46 Nut Flg Top Lock Bracket Gauge Wheel Lf Bracket Gauge Wheel Rf Pulley Idler V-Groove Dim 4.25 Washer 11/32 x 13/16 x 16 Ga. Nut Crownlock 3/8-16 unc

KEY NO. 185 ----

PART NO. 55-17 55-13 77-16 54-16 57-16 59-10 69-18 02-16 54-15 60-18 42-13 39-93 06-12 14-11 06-11 05-16 56-17 60-72 04-18 63-18 08-18 63-18 82-18 18-18 18-18 85-23
DESCRIPTION Cover Mandrel Lh Cover Mandrel Rh Screw Thd Roll 1/4-20 x 5/8 Arm Idler Spacer Retainer PM Mower Spring Tension Belt Knob Rd 3/8-16 Plstc Thds Blk Hex-Belt 92 Mower Shaft Asm W/Lwr Brg Rh Thd CRD Keeper Belt Idler Bolt Shoulder Wheel Gage Donut Wide Nut Centerlock 3/8-16 unc Washer 3/8 x 7/8 x 14 Ga. Bolt Carr Sh 3/8-16 x 1-1/2 Gr. 5 Bolt Rdhdsqnk 5/16-18 unc x 3/4 Chute Bagger CRD Cable Clutch CRD Service Screw Hex Thdcut 1/4-20 x 5/8 Blade Cross Lh 92 Adpater Blade Cross Blade Cross Rh 92 Head Asm. Cable Clutch Mandrel Asm Service Mandrel Asm CRD Lh Threads SVC Replacement Mower Complete- (Std. deck Order separately gauge wheel components Key Nos. 116-119)

BAGGER

Bagger Asy (CRD)_5
KEY PART NO. NO. 16 52-14 04-12 39-16 99-98 10-98 10-40 10-18 13-14 04-18 12-16 57-16 96-11 06-52 06-90 06-14 05-11 12-90 05-16 96-18 08-16 57-16 57-16 57-18 01-16 57-16 57-16 94-12 68-13 20-17 54-01 05-18 09-16 96-80 05-17 40-83

DESCRIPTION Tube Handle Bagger CRD Bolt Carriage 1/4-20 x 2.0 Gr.5 Nut Lock 1/4 Lge Flg Gr. 5 Zinc Handle Bagger w/Lvrs Gr. 5 Zinc Screw Pan Head #10-24 x 1.50 Blk Screw Pan Hd Nut Wiz Lock Hex Serr/Hd #10-24 Cover Bagger Steel Bolt Carriage 1/4-20 x 2.25d x Gr. 5 Tube Support Bagger CRD Bracket Support Upper Bag CRD Bracket Horiz. Adj Bagger Bolt Rdhd Sht Sqnk 3/8-16 x 3/4 Bolt Hex 3/8-16 x 2-1/4 Gr. 5 Nut Lock Flg 3/8-16 unc Bolt Rdhd Sht Sqnk 5/16-18 unc x 3/4 Washer 11/32 x 3/4 x 16 Ga. Nut Lock Hex Flange 5/16-18 Bracket Horiz Adj Bagger Bag Asm CRD Bracket Side Bagger CRD Tube Upper Bagger CRD Tube Pivot Bagger CRD Tube Front Bagger CRD Tube Lower Bagger CRD Grip Handle Black Retainer Clip Rivet Rd Hd Drilled 3/8 Dia Washer 13/32 x 1-1/4 x 16 Ga. Plug Support Bagger CRD Bolt 5/16-18 x 2-1/2 Seal Trim 37" Bracket Vert Adj Bagger CRD Nut Lock Hx w/Ins 5/16-18 unc Plug Tubing End

SERVICE

POLICY

WARRANTY

LIMITED WARRANTIES FOR NEW PEERLESS GEAR POWER TRAIN COMPONENTS

A. Products Warranted

TECUMSEH
Issued January 1980 Revised January 1991
Peerless Gear and Machine Division of Tecumseh Products Company (Tecumseh), subject to the limitations contained below, will,at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is found upon examination by any Tecumseh Authorized Service Outlet or by Tecumsehs factory in Grafton, Wisconsin, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and Series 1100 angle drive and ONE YEAR for all other Peerless products. New Power Train Components incorporated in equipment used for commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY (30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to the original purchaser.

B. Products And Items Not Warranted
Alterations or Modications of Power Train Components. Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturers Manual. This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of service items which are not defective shall be paid for by the original purchaser. 1. 2.
C. Securing Warranty Service
Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service can only be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of requesting warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any charges for making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work is performed. The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train Components and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.
D. Limitation of Damages and Implied Warranties
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any of its afliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any of its parts, other than as set forth herein. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s) may not apply to you. This warranty gives you specic legal rights and you may also have other legal rights which vary from state to state.

E. No Dealer Warranty

Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume for Tecumseh any other obligations or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or limitations of Tecumsehs warranty in any way.

SERVICE NOTES

LZ12592RB MBA1492BRK MBA16107BRK MC11T92RB MC1292RB MC12592RB M135B92RB M13B92RB P1292RB P135B92RB RB135B92 REN1192RB RE12592RBK

02227_PL_LT_CRD

Instruction manual
Please read these instructions carefully and make sure you understand them before using this machine.

Manuel dinstructions

Merci de lire trs attentivement le manuel d'instructions. Assurez-vous d'avoir tout compris avant d'utiliser ce tracteur.

Manuale di istruzioni

Prima di utilizzare la macchina leggete queste istruzioni con attenzione ed accertatevi di averle comprese bene.

Anleitungshandbuch

Bitte lesen Sie diese Anleitungen sorgfltig durch und vergewissern Sie sich, da Sie diese verstehen, bevor Sie die Maschine in Betrieb nehmen.
Instructieboekje Manual de las instrucciones
Por favor lea cuidadosamente y comprenda estas intrucciones antes de usar esta maquina. Lees deze instructies aandachtig en zorg dat u ze begrijpt voordat u deze machine gebruikt.
Safety rules. Sicherheitsvorschriften. Rgles de scurit. Assembly. Zusammenbau. Montage. Functional description. Funktionsbeschreibung. Description du fonctionnement. Before starting. Manahmen vor dem Anlassen. Avant de dmarrer. Driving. Betrieb. Conduite.
Reglas de seguridad. Norme antinfortunistiche. Veiligheidsregels. Montaje. Montaggio. Montering. Descripcin del funcionamiento. Funzionamento. Beschrijving van functies. Antes del arranque. Prima dellavviamento. Maatregelen vr het starten. Conduccin. Guida. Rijden.
Maintenance, adjustment. Mantenimiento, ajuste. Wartung (Instandhaltung), Einstellung. Manutenzione. Entretien, rglages. Onderhoud, afstelling. Troubleshooting. Strungssuche. Recherche des pannes. Storage. Aufbewahrung. Remisage. Bsqueda de averas. Ricerca guasti. Het localiseren van fouten. Conservacin. Rismessaggio. Stallen.
We reserve the right to make changes without prior notice. nderungen ohne vorherige Mitteilung sind vorbehalten. Nous nous rservons le droit d'apporter des modications sans avis pralable. Nos reservamos el derecho a introducir modicaciones sin previo aviso. Ci riserviamo il diritto di modiche o cambiamenti senza preavviso. Wij houden ons het recht voor om veranderingen aan te brengen zonder voorafgaande mededeling. 2

1. Safety Rules

Safe Operation Practices for Ride-On Mowers
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

I. Training

Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. Never allow children or people unfamiliar with the instructions to use the lawnmower. Local regulations may restrict the age of the operator. Never mow while people, especially children, or pets are nearby. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property. Do not carry passengers. All drivers should seek and obtain professional and practical instruction. Such instruction should emphasize: - the need for care and concentration when working with ride-on machines; - control of a ride-on machine sliding on a slope will not be regained by the application of the brake. The main reasons for loss of control are: a) insufcient wheel grip; b) being driven too fast; c) inadequate braking; d) the type of machine is unsuitable for its task; e) lack of awareness of the effect of ground conditions,especially slopes; f) incorrect hitching and load distribution.

II. Preparation

While mowing, always wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing open sandals. Thoroughly inspect the area where the equipment is to be used and remove all objects which may be thrown by the machine. WARNING - Petrol is highly ammable. - Store fuel in containers specically designed for this pur pose. - Refuel outdoors only and do not smoke while refueling. - Add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the engine is running or when the engine is hot. - If petrol is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until petrol vapors have dissipated. - Replace all fuel tanks and container caps securely. Replace faulty silencers. Before using, always visually inspect to see that the blades, blade bolts and cutter assembly are not worn or damaged. Replace worn or damaged blades and bolts in sets to preserve balance. On multi-bladed machines, take care as rotating one blade can cause other blades to rotate.

III. Operation

Do not operate the engine in a conned space where dangerous carbon monoxide fumes can collect. Mow only in daylight or in good articial light.
Before attempting to start the engine, disengage all blade attachment clutches and shift into neutral. Do not use on slopes of more than 5. Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care. To guard against overturning; - do not stop or start suddenly when going up or downhill; - engage clutch slowly, always keep machine in gear, especially when traveling downhill; - machine speeds should be kept low on slopes and during tight turns; - stay alert for humps and hollows and other hidden hazards; - never mow across the face of the slope, unless the lawnmower is designed for this pur pose. Use care when pulling loads or using heavy equipment. - Use only approved drawbar hitch points. - Limit loads to those you can safely control. - Do not turn sharply. Use care when reversing. - Use counterweight(s) or wheel weights when suggested in the instruction handbook. Watch out for trafc when crossing or near roadways. Stop the blades from rotating before crossing surfaces other than grass. When using any attachments, never direct discharge of material toward bystanders nor allow anyone near the machine while in operation. Never operate the lawnmower with defective guards, shields or without safety protective devices in place. Do not change the engine governor settings or overspeed the engine. Operating the engine at excessive speed may increase the hazard of personal injury. Before leaving the operators position: - disengage the power take-off and lower the attachments; - change into neutral and set the parking brake; - stop the engine and remove the key. Disengage drive to attachments, stop the engine, and disconnect the spark plug wire(s) or remove the ignition key - before cleaning blockages or unclogging chute; - before checking, cleaning or working on the lawnmower; - after striking a foreign object. Inspect the lawnmower for damage and make repairs before restarting and operating the equipment; - if the machine starts to vibrate abnormally (check immediately). Disengage drive to attachments when transporting or not in use. Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless adjustment can be made from the operators position. Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing.

To install bagger components to tractor

1. 2. 3. 4. 5.

1. Discharge Chute 2. 3/8 Nut 3. Flat Washer
Support Bracket Clevis Pin 10 x 17mm 1 Retainer Spring Clevis Pin 10 x 50mm 10,3mm (13/32") flat washer
Remove discharge chute from rear of tractor. Unhook the two (2) straps and pull chute out and away from tractor. Remove the two (2) 3/8 nuts and at washers from the bolts at the tractor back plate.
Install the two upper support brackets through the back plate and to the chassis, install the clevis pin 10x17mm and secure with retainer spring. Assemble both support brackets to the outside of the baggger support tube install the clevis pin 10x50mm and secure with retainer spring.
1. 3/8 Lock nut 2. Flat Washer 3. Support Tube
1. Hook 2. Discharge Chute 3. Back plate slot
Using the nuts and at washers removed from tractor back plate, install the bagger support tube to the back plate as shown. Tighten securely.
Replace discharge chute into rear opening of tractor. Secure the chute with the two hook straps. NOTE: The strap hook must go through the discharge chute only. Do not allow the hook to enter the slot in the tractor back plate. This will allow the discharge chute to oat with the mower deck when moving on uneven terrain.

To Assemble Bagger

NOTE: For ease of assembly, you may wish to obtain the assistance of another person when putting the bagger together. Holes in front bagger tube are at an angle. Place front bagger tube against lower bagger tube and check for proper hole alignment before assembling bolts. Assemble front and lower bagger tubes using four (4) 1/4 x 50,8mm carriage bolts and lock nuts supplied. Tighten securely. Slide front and lower bagger tube assembly into the bagger assemby. Assemble front and upper bagger tubes using four (4) 1/4 x 50,8mm carraige bolts and lock nuts supplied. Tighten securely. Slip all the vinyl bindings over the bagger tubes Slide the bagger dump handle through the hole in the bagger top, install the clevis pin and secure with retainer spring. Push cap over end of bagger dump handle. NOTE: For future use, the clevis pin may be removed in order to use the handle to clear the chute in the event it has become clogged.
1. Front bagger tube 2. Lower bagger tube 3. 1/4 x 50,8mm Carriage Bolts 4. 1/4 Lock nut
1. Front bagger tube 1 2. 1/4 x 50,8mm Carriage Bolts 3. 1/4 Lock nut 4. Vinyl Binding 5. Dump handle tube 6. Clevis pin 7. Retainer spring 8. Cap

Bagger adjustment

For proper bag function and appearance, it may be necessary to adjust the bagger assembly. There should be 6mm (1/4")-9mm (3/8") gap between the bagger top and fender and the bagger top surface should be even with the top surface of the fender. To adjust bagger position:

Oliepeil

De gecombineerde olie-bijvuldop en peilstok worden bereikbaar, nadat de motorkap is opengeklapt. Het oliepeil in de motor dient vr ieder gebruik te worden gecontroleerd. Zorg ervoor dat de maaier horizontaal staat. Schroef de oliepeilstok eruit en maak hem schoon. Schroef de peilstok er opnieuw in. Draai vast en haal hem er weer uit en lees het oliepeil af.
The oil level should lie between the two markings on the oil stick. If more oil is needed add SAE 30 oil to the FULL marking. SAE 5W-30 oil should be used during the winter (below freezing point). Der lstand soll zwischen den beiden Marken auf dem Mestab liegen. Wenn dies nicht der Fall ist, Motorl SAE 30 bis zur Marke FULL einfllen. Im Winter (bei Frostgefahr) ist Motorl SAE 5W-30 anzuwenden. Le niveau atteint par l'huile doit se trouver entre les deux repres sur la jauge. Si ce n'est pas le cas, faire l'appoint avec de l'huile moteur SAE 30 jusqu'au repre "maxi" (FULL), jamais au dessus. En hiver, lorsque la temprature est infrieure 0, utilser de l'huile moteur SAE 5W30. El nivel de aceite ha de estar entre las dos marcas de la varilla. Si no es este el caso, aadir aceite para motor SAE 30 hasta la marca de FULL (lleno). En invierno (a temperaturas bajo cero) hay que utilizar aceite de motor SAE 5W-30. Lolio deve essere tra i due contrassegni sullasticella. Se necessario rifornire con olio SAE 30, no al segno FULL. In inverno (sotto 0) usare olio SAE 5W-30. Het oliepeil dient tussen de beide markeringen op de stok te liggen. Als dit niet het geval is, moet u met SAE 30 tot het FULL-merk bijvullen. S-winters (onder het vriespunt) dient motorolie SAE 5W-30 te worden gebruikt.

CAUTION - DO

Tire air pressure
Check the tire pressure regularly. The pressure in the front tires should be 1 bar (14 PSI) and 0.8 bar (12 PSI) in the back tires.

Reifendruck

Den Luftdruck in den Reifen regelmig prfen. Der Druck in den Vorderreifen soll 1 bar betragen, in den Hinterreifen 0,8 bar.
Pression de gonage des pneus
Vrier rgulirement la pression de gonage des pneus. La pression de l'air dans les pneus doit tre de 1 bar pour les roues avant et de 0,8 bar pour les roues arrires.

Driving

Lower the cutting unit by moving the lever forwards. Connect the cutting unit. Choose a driving speed which suits the terrain and required cutting results. Release the brake/clutch pedal slowly.

Betrieb

Das Mhaggregat durch Vorwrtsfhren des Hebels absenken. Das Mhaggregat einkuppeln. Eine an das Gelnde und das gewnschte Mhergebnis angepate Geschwindigkeit whlen. Kupplungs- und Bremspedal langsam zurckfedern lassen.

Conduite

Abaisser le carter de coupe en amenant le levier vers l'avant. Embrayer les lames. Choisir la vitesse d'avancement en fonction du terrain et de la qualit de tonte dsire (Gnralement, la position optimale correspond l'encoche prvue cet effet au niveau de la commande des gaz). Relcher doucement la pdale d'embrayage/frein.

Conduccin

Descender la unidad de corte empujando la palanca haciaadelante. Acoplar la unidad de corte. Elegir la velocidad adecuada al terreno y al corte deseado. Soltar lentamente el pedal de embrague/freno.
Abbassare il dispositivo di taglio springendo in avanti la leva relativa. Inserire il tagliaerba. Selezionare una velocit di guida adeguata al terreno e al risultato di taglio desiderato. Rilasciare lentamente il pedale freno/frizione.

Rijden

Verlaag de maaikast doorde hendel naar voren te brengen. Schakel de maaikast. Kies een rijsnelheid die geschikt is voor het terrein en voor het gewenste maairesultat. Laat de koppelings-/rempedaal langzaam omhoogkomen.

Cutting tips

Clear the lawn from stones and other objects which can be thrown away by the blades. Localize and mark stones and other xed objects to avoid collision. Begin with a high cutting height and reduce until the required cutting result is obtained. The cutting result is best with high engine speed (blades rotate quickly) and low gear (machine goes slowly). If the grass is too long and thick the drive speed can be increased by selecting a higher gear or reducing the motor speed, without affecting the cutting result. The best lawn is achieved if the grass is cut often. Cutting becomes more even and the cut grass is more evenly distributed over the surface. Total time taken is not greater, since higher drive speed can be selected without affecting the cutting results. Avoid cutting wet grass. The cutting results will be worse since the wheels will sink into the soft lawn. Spray the cutting unit with water underneath after use.

Svuotamento del cesto

Il vostro trattore dotato di un cicalino che segnala quando il cesto di raccolta pieno. Per disinserire l'allarme, azionare il pulsante di innesto lame. Posizionarsi in un luogo adatto allo scarico dell'erba Mettere in folle e inserire in freno a mano Alzare la maniglia per lo scarico. Tirare verso l'operatore per sollevare il cesto di raccolta e svuotarlo. Per continuare il lavoro di falciatura, vericare che il cesto sia completamente abbassato, e che si trovi in posizione corretta per lavorare.

To Dump Bagger

Your tractor is equipped with a Dump Bag Alarm. To turn off the alarm disengage the attachment clutch switch. Position tractor in location you wish to dump bagger. Place motion control lever in Neutral position and set parking brake. Raise dump handle to its highest position. Pull handle forward to raise bagger and dump clippings. To continue mowing, be sure bagger is down and in proper operating position which will allow mower to operate.
Het legen van de grascontainer
Uw trekker is voorzien van een alarm voor het legen van de container. Om het alarm uit te zetten moet u de schakelaar voor de containerbevestiging uitzetten. Plaats de trekker op de plek waar u de grascontainer wilt legen. Zet de versnellingshendel in z'n neutraal en haal de handrem aan. Hef de hendel voor het legen naar de hoogste stand. Trek de hendel naar voren om de grascontainer omhoog te laten komen en het grasmaaisel te storten. Om met maaien verder te kunnen gaan, moet u ervoor zorgen dat de grascontainer weer naar beneden is en in de juiste stand staat.
Entleeren der Grasfangbox
Der Traktor ist mit einer Alarmfunktion ausgestattet die signalisiert, wenn die Grasfangbox voll ist. Um den Alarm zu unterbrechen lsen Sie den Verbindungsstecker. Fahren Sie den Traktor an die Stelle, an der Sie die Box entleeren mchten. Setzen Sie den Schalthebel auf Neutral und ziehen Sie die Handbremse an. Ziehen Sie den Handgriff zur Entleerung der Grasfangbox ganz nach oben. Ziehen Sie anschlieend den Handgriff ganz nach vorne, um die Grasfangbox zu kippen und das Schnittgut zu entleeren.

To convert mower

(Converting to mulching or rear discharging will require the purchase of these accessories.) To mulching Place deck into the high cut position. Remove bagger or optional rear discharge deector. Unhook the two (2) straps and remove discharge chute. Insert plug and handle assembly through back plate and onto the mower deck chute adaptor. Retain the plug assembly by connecting the two straps over the handle and hook into the holes provided. Replace bagger or optional rear discharge deector to allow mower to operate. You are now ready to begin mulching. To rear discharging Place deck into the high cut position. Remove bagger and mulching plug (if installed). Install discharge chute through opening in backplate and slide over deck adaptor. Attach the chute by hooking the two straps into the holes in the ange of the chute. Install the discharge deector to the backplate by screwing the four (4) wing screws into the threaded inserts located in the backplate. Tighten the wing screws securely. To bagging Place deck into the high cut position. Remove the rear discharge deector or mulching plug. Insert the discharge chute into the opening in the backplate and onto the mower deck adaptor. Attach the chute to the tractor by hooking the two straps to the ange of the chute. Install bagger onto tractor. Fixieren Sie den Kanal, indem Sie die beiden Haken in die dafr vorgesehenen Bohrungen einrasten lassen. Montieren Sie den Deflektor, indem Sie die vier (4) Flgelschrauben in die dafr vorgesehanan Bohrungen, die sich in der hinteren Platte des Traktors benden, befestigen. Ziehen Sie die Flgelschrauben fest an. Sammelfunktion (Grasfangbox) Mhdeck in chste Schnittposition bringen. Entfernen Sie den Deektor oder den Mulcheinsatz (fals dieser montiert ist). Installireen Sie den Adapter des Mhdecks. Fixieren Sie den Kanal, indem Sie die beiden Haken in die dar vorgesehenen Bohrungen einrasten lassen. Setzen Sie anschlieend die Grasfangbox wieder auf.