C 22 CE

STEREO PRE-AMPLIFIER

McIntosh

The Compendium

FRONT PANEL: Glass with illuminated teal/gold nomenclature and gold anodized aluminum panel. BALANCE: LEFT to RIGHT. INPUT SELECTOR (with indicator lights): TAPE 2, TAPE 1, CD, TUNER, PHONO 1, PHONO 2, AUX 1, AUX 2. MODE SELECTOR (with indicator lights): L TO L+R, R TO L+R, STEREO REV, STEREO, MONO (L+R), L+R TO L and L+R TO R. VOLUME. 7 LEFT BASS control. RIGHT BASS control. Rocker switches: TAPE 1 NORMAL or MONITOR, TAPE 2 NORMAL or MONITOR. POWER: ON or OFF. AUX 2 INPUT jack. SPEAKERS switch: OFF, 1, 2, 1 & 2. HEADPHONES jack. Rocker switches: RUMBLE: FLAT or FILTER, HF: FLAT or FILTER. LOUDNESS: NORMAL or COMPENSATED. LEFT TREBLE control. RIGHT TREBLE control.
BACK PANEL: AC outlets: 4 SWITCHED, 1 UNSWITCHED. LEFT and RIGHT BALANCED OUTPUTS. OUTPUTS: SWITCHED: 1 and 2, MAIN, TAPE 2, TAPE 1. HIGH LEVEL INPUTS: AUX 1, TAPE 2, TAPE 1, CD, TUNER. LOW LEVEL INPUTS: PHONO 1 and PHONO 2. GrouND binding post. 7 Power cord. Speaker Control Relay socket. Tube cover. SPECIFICATIONS: Response 20-20kHz (+0 -0.5dB). Distortion 0.02% IHF. Noise and hum: - 90dBa high level, -80dBa re 10mV phono. Output rated 2.5v, 8V max. Input sensitivity and impedance: high level 0.25V at 22k, phono 2.2mV at 47k and 65pF. Individual tone controls: bass and treble +20dB to -20dB. Rumble filter 50Hz at 12dB/octave. HF filter 5kHz at 12dB/octave. Voltage gain 20dB aux, 61dB phono. TUBES: 3-12AT7, 4-12AX7. Solid state rectifier.
2007 VintageMac Larry Hodson

Rev.107

Page 1 / 2
C 22 CE - Sold from 1995 -. S/N: LK1001~????? Size 5-7/16"H, 16"W and 14"D behind panel. Weight 16 lb. $2,500.00

Page 2 / 2

END CAPS

020-005

McIntosh

The Compendium

020-005 (5-7/16 OR 5-3/16) Gold anodized aluminum. Polished face, sides, top and bottom. Press-fit onto pins protruding from the ends of the face plate. Removable (to access side controls). Reversible. Used on: PREAMP: C 11 C 20 (MID) C 20 (LATE) TUNER: MR MR MR MR 65 65A 65B 66 TUNER/PRE-AMP: MX 110 (EARLY) MX 110 (MID)
MR 65 Note: McIntosh made an undocumented change in the front panels and end caps during production. Some early units had end caps 5-3/16 tall and with a 4-1/2" pin spacing most of the above models had end caps 5-7/16 tall and with a 4-3/4" pin spacing. The McIntosh part number was the same for both versions of the end caps.
020-005 END CAPS - Used from 1960 - 1963.
2007 VintageMac Larry Hodson

Rev.107

Page 1 / 26
018-043 & 018-044 / 018-520 & 018-521
018-044 (L) & 018-043 (R) (5-7/16) 018-520 (L) & 018-521 (R) (5-7/16) for C 22 CE Anodized aluminum. Polished face, top and bottom. Sanded sides. Off-center, point on face. Milled groove on inside for upper glass. Attached with screws. Used on: PREAMPS: C 22 C 24 C 22 CE TUNERS: MR 67 MR 71 TUNER/PRE-AMPS: MX 110 (LATE) INTEGRATED AMPS: MA 230 MA 5100
C 22 018-043 & 018-044 END CAPS - Used from 1963 - 1972 018-520 & 018-521 END CAPS - Used from 1995 - ???? 2007 VintageMac Larry Hodson

Page 2 / 26

018-132 & 018-133
018-133 (L) & 018-132 (R) (5-7/16) Anodized aluminum. Polished face, top and bottom. Sanded sides. Off-center, point on face. Milled inset on outside. Attached with screws. Used on: SCOPE: MI 3
018-132 & 018-133 END CAPS - Used from 1964 - 1971. 2007 VintageMac Larry Hodson

Page 3 / 26

018-120
018-120 (5-7/16) Anodized aluminum. Polished face, top and bottom. Sanded sides. Off-center, point on face. Reversible. Attached with screws. Used on: POWER AMP: MC 2505 PREAMPS: C 26 C 28 TUNERS: MR 73 MR 74 MR 77 TUNER/PRE-AMPS: MX MX MX MX 114 115
018-120 END CAPS - Used from 1969 - 1985. 2007 VintageMac Larry Hodson Page 4 / 26

018-080

018-080 (5-1/2) Anodized aluminum. Polished face, top and bottom and sides. Stepped side. Flat face. Reversible. Attached with screws. Used on: RECEIVERS: MAC 1500 MAC 1700

MAC 1500

018-080 END CAPS - Used from 1965 - 1973.

Page 4 / 26

018-0??
018-0?? (5-1/2) Anodized aluminum. Polished face, top and bottom and sides. Smooth side. Flat face. Reversible. Attached with screws. Used on: RECEIVER: MAC 1900

MAC 1900

018-0?? END CAPS - Used from 1973 - 1978. 2007 VintageMac Larry Hodson Page 6 / 26

018-112

018-112 (7-1/8) Anodized aluminum. Polished face, top and bottom. Sanded sides. Off-center, point on face. Finger slots on sides. Reversible. Attached with screws. Used on: POWER AMP: MC 2105

MC 2105

018-112 END CAPS - Used from 1967 - 1977.

Page 7 / 26

018-154
018-154 (5-7/16) Anodized aluminum. Polished face, top and bottom. Sanded sides. Off-center, point on face. Finger slots on side. Reversible. Attached with screws. Used on: INTEGRATED AMP: MA 6100

MA 6100

018-154 END CAPS - Used from 1972 - 1979. 2007 VintageMac Larry Hodson

Page 8 / 26

018-204
018-204 (3-5/8) Anodized aluminum. Polished face, top and bottom. Sanded sides. Flat face. Finger slots on side. Reversible. Attached with screws. Used on slim-line models: POWER AMP: MC 502 PRE-AMP: C 504 TUNERS: MR 500 MR 510

MC 502

018-204 END CAPS - Used from 1978 - 1990. 2007 VintageMac Larry Hodson

018-160

018-160 (5-3/8) SECURED WITH 101-035 SCREWS Anodized aluminum. Polished face, top and bottom. Sanded sides. Flat face. Finger slots on side. Reversible. Attached with screws. Used on: POWER AMPS: MC 2125 MC 2155 PRE-AMPS: C C C C C 33 TUNERS: MR 75 MR 78 MR 80 TUNER/PRE-AMP: MX 117 SCOPE: MPI 4

INTEGRATED AMP: MA 6200

018-160 END CAPS - Used from 1973 - 1986.

Page 10 / 26

018-173
018-173 (7-1/8) SECURED WITH 101-042 SCREWS Anodized aluminum. Polished face, top and bottom. Sanded sides. Flat face. Finger slots on side. Reversible. Attached with screws. Used on: POWER AMPS: MC 2205 MC 2255 MC 2002

MC 2255

018-173 END CAPS - Used from 1975 - 1988.

Page 11 / 26

018-438

018-438 (3-5/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Flat face. Reversible. Attached with screws. Used on slim line models: POWER AMP: MC 7100 PRE-AMP: C 712 TUNER: MR 7084 HOME THEATER: MAC 3 MSD 4

MC 7100

018-438 END CAPS - Used from 1992 - 1999. 2007 VintageMac Larry Hodson Page 12 / 26

018-232

018-232 (5-3/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Flat face. Reversible. Attached with screws. Used on: POWER AMPS: MC 7150 MC 150 PRE-AMPS: C C C C C C C C 34V 31V TUNERS: MR 7082 MR 7083 DISC PLAYERS: MCD MCD MCD MCD MCD MCD 7009 7010

HOME THEATER: MX 118

INTEGRATED AMPS: MA 6400 MA 6450
MC 7150 018-232 END CAPS - Used from 1985 - 1999. 2007 VintageMac Larry Hodson

Page 13 / 26

018-345
018-345 (7-1/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Flat face. Reversible. Attached with screws. Used on: POWER AMPS: MC MC MC MC MC MC MC 300 PRE-AMP: C 39 INTEGRATED AMPS MA 6800 MA 6850 HOME THEATER: MX 130

MULTI-ZONE: CR 10 CR 12

C 39 018-345 END CAPS - Used from 1985 - 1999. 2007 VintageMac Larry Hodson

Page 14 / 26

018-???
018-??? (7-5/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Flat face. Reversible. Attached with screws. Used on: DISC PLAYER: MLD 7020

MLD 7020

018-??? END CAPS - Used from 1998 200? 2007 VintageMac Larry Hodson Page 15 / 26

018-610

018-610 (3-5/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMP: MC 122 PRE-AMP: C 15 D TO A CONVERTER: MDA 700
018-610 END CAPS - Used from 1998 200? 2007 VintageMac Larry Hodson Page 16 / 26

018-630

018-630 (5-3/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMPS: MC 162 MC 202 PRE-AMPS: C C C C TUNER: MR 85 DISC PLAYERS: MVP 831 MVP 841 MCD 205 MVP 851 MVP 861 MUSIC SERVER: MS 300

MVP 841

018-630 END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson

Page 17 / 26

018-??? (6) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: PRE-AMPS: C 200 C 220 DISC PLAYER: MCD 201
018-??? END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson

Page 18 / 26

018-612
018-612 (7-1/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMPS: MC MC MC MC HOME THEATER: MX 132 INTEGRATED AMPS: MA 6900 MA 6500 MULTI-ZONE: CR 16

MC 7205

018-612 END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson Page 19 / 26
018-??? (7-5/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: PRE-AMP: C 2200 INTEGRATED AMP: MA 6300 HOME THEATER: MX 134 MX 119

C 2200

018-??? END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson Page 20 / 26

018-615

018-615 (8-7/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMP: MC 352

MC 352

018-615 END CAPS - Used from 200? 200?

Page 21 / 26

018-??? (9-1/2) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMP: MC 207 HOME THEATER: MHT 100 MHT 200 MX 135

MHT 100

018-??? END CAPS - Used from 200? 200?

Page 22 / 26

018-615 (10-1/8) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Tapered face from outer edge to inner edge. Reversible. Attached with screws. Used on: POWER AMP: MC 2102 INTEGRATED AMP: MA 2275

MC 2102

Page 23 / 26
018-??? (6) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Stepped transition between outer beveled edge and flat inner portion of face. Reversible. Attached with screws. Used on: DISC PLAYER: MCD 1000 D TO A CONVERTER: MDA 1000

MCD 1000

018-??? END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson Page 24 / 26

018-717

018-717 (8-13/16) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Stepped transition between outer beveled edge and flat inner portion of face. Reversible. Attached with screws. Used on: POWER AMP: MC 501

MC 501

018-717 END CAPS - Used from 200? 200? 2007 VintageMac Larry Hodson Page 25 / 26
018-??? (9-7/16) Anodized aluminum. Brushed satin finish on face, sides, top and bottom. Stepped transition between outer beveled edge and flat inner portion of face. Reversible. Attached with screws. Used on: POWER AMPS:

MC 402 MC 252

MC 252

Page 26 / 26