Telestar RB-60.qxd

4/11/06

2:04 PM

Page 1

www.meade.com

TELESTAR INSTRUCTION MANUAL
60mm | 2.4" Altazimuth Refracting Telescope

Page 2

The tube has a focal length of 700mm, and its objective lens has a diameter of 60mm. The lens diameter is one of the most important pieces of information about the telescope. The size of the objective lens determines how much detail you will be able to see in your telescope. The focal length will help later on to calculate magnification.

4/11/06 2:04 PM

INTRODUCTION
Your telescope is an excellent beginners instrument, and is designed to observe objects in the sky and also on land. It can be your personal window on the universe or allows you to intimately study the behavior of nesting birds on a distant hillside. The telescope is shipped with the following parts: Optical tube Aluminum tripod with an accessory tray Two 1.25" eyepieces: MA25mm (28X), MH9mm (78X) 2x 1.25" Barlow lens Diagonal mirror Red dot viewfinder with bracket Telescope mount

Page 3

Setting up your telescope involves these simple steps: Assemble your tripod Attach the accessory tray Attach the optical tube to the mount Attach the red dot viewfinder Attach the diagonal mirror and eyepiece Align the red dot viewfinder Study the the picture on the next page and become acquainted with the parts of your telescope. Then proceed to Assemble your Tripod.
1. Eyepiece 2. Red dot viewfinder (see Inset A) 3. Red dot viewfinder alignment screws (see Inset A) 4. Optical tube assembly 5. Vertical locking lever 6. Horizontal lock knob 7. Tripod legs 8. Leg brace supports (See Inset C) 9. Leg brace (See Inset C) 10. Mount base attachment knobs 11. Optical tube lock knobs 12. Horizontal slow motion control (See Inset B) 13. Diagonal mirror 14. Objective lens cell 15. Focuser drawtube 16. Vertical slow motion control (See Inset B) 17. Accessory tray (Inset C) 18. Red dot viewfinder bracket (see Inset A) 19. Adjustable sliding leg extension (see Inset C) 20. Tripod leg lock (see Inset C) 21. Dew shield/lens shade 22. Front lens cap (removed) 23. Focusing knob 24. Mount base attachment 25. Quickrelease (Inset A)

FIGURE 1

Figure 1: Telestar RB-60 Altazimuth Refracting Telescope Inset A: Red Dot Viewfinder Assembly Inset B: Tripod Legs and Accessory Tray Inset C: Altaz or Altazimuth Mount

Page 4

Inset A

Inset C

Inset B

ASSEMBLE YOUR TRIPOD

The tripod is the basic support for your telescope. Adjust the height of the tripod so that you can view comfortably. 1. Unlock the leg lock (20). 2. Slide the leg in or out to the desired length. 3. Tighten the leg lock to secure the leg in place. 4. Repeat for the other two legs. 5. Next, spread the legs out evenly apart. ATTACH THE ACCESSORY TRAY
The tray (17) helps stabilize the tripod and is also a convenient holder of eyepiece and other Meade accessories, such as the Barlow lens. 1. Place the accessory tray over the center hub of the leg brace supports.

Page 5

Fig. 2
The optical tube gathers distant light which is focused in the eyepiece. 1. Remove the two lock knobs from the optical tube. (Fig. 3) 2. Slide the two bolts through the holes in the mounting bracket. 3. Thread a lock knob onto each of the mounting screws and tighten to a firm feel.

2. Rotate the tray, until the corners of the tray "click" into place. ATTACH THE MOUNT TO THE TRIPOD
ATTACH THE OPTICAL TUBE TO THE MOUNT
1. Slide the center post of the mount into the center hole on top of the tripod. 2. Tighten the lock knob (10) underneath the top of the tripod to firm feel. Notice that the lock knob is already attached to the tripod.
ATTACH THE RED DOT VIEWFINDER

Fig. 4

It can be difficult locating objects in the sky using the eyepiece. The red dot viewfinder has a red dot "bullseye" to help you more easily locate and line up with a celestial target. Slide the red dot viewfinder into the mounting bracket until it clicks into place. Note that the red dot viewfinder has a quick release control. To detach from the bracket, press the bracket quick release button and slide the bracket out.

Fig. 3

ALIGN THE RED DOT VIEWFINDER
Perform the first part of this procedure during the daytime and the last step at night. 1. Point the telescope at an easy-to-find land object such as the top of a telephone pole or a distant mountain or tower. Look through the eyepiece in the diagonal mirror and turn the focuser knob (23) until the image is sharply focused. Center the object precisely in the eyepieces field of view.

1. 2. 3. 4.

The diagonal mirror reflects the light from the optical tube to a more comfortable viewing position for the eyepiece. Slide the diagonal mirror into the focuser drawtube. Tighten the drawtube thumbscrew to hold the diagonal mirror securely. Slide the 25mm eyepiece into diagonal mirror. Tighten the diagonal mirror thumbscrew to hold the eyepiece securely.
ATTACH THE DIAGONAL MIRROR AND EYEPIECE

Page 6

2. Look through the red dot viewfinder. Turn one or more of the viewfinders alignment screws (3) until the red dot is precisely over the same object as you centered in the eyepiece. 3. Check this alignment at night on a celestial object, such as the Moon or a bright star, and use the viewfinders alignment screws to make any necessary refinements. TO MOVE THE TELESCOPE Your RB-60 telescope is altazimuth mounted. Altazimuth is just a complicated way of saying that your telescope moves up and down and from side to side. Other telescopes may be mounted in different ways. 1. Slightly loosen the vertical locking lever (5). Loosening this lever allows you to move the telescope up and down. 2. Slightly loosen the horizontal lock knob (6). Loosening this lock allows the telescope to be moved from side to side. 3. Once an object is found, re-tighten the knob. You can then use the slow motion controls to make smooth and precise

THE MOST IMPORTANT RULE

We have one very important rule that you should always follow when using your telescope:
Have a good time when youre observing. You may not know everything that there is to know about a telescope or what all the sights in the universe are, but thats OK. Just point and observe at first.

movements as you follow (or track) an object as it moves in the eyepiece.

Have Fun!

You will begin to grow and learn more about astronomy the more you observe. Go to the library and read some books about the stars and planets. Read about astronomers of old. Many of them had telescope no bigger than the one you are using right now. Galileo, who is one of the first astronomers to use a telescope, discovered four of the moons of Jupiter with a telescope about the same size as yours (and his didnt even focus very well!). OBSERVING
You will enjoy your telescope even more as you learn more about it. But dont be scared off by difficult terms or complicated procedures. Dont panic! Just relax and enjoy your scope.
Observe during the daytime: Try out your telescope during the daytime at first. It is easier to learn how it operates and how to observe when it is light. Pick out an easy object to observe: A distant mountain, a large tree, a lighthouse or skyscraper make excellent targets. Point the optical tube so it lines up with your object.

Page 7

LOOKING AT OR NEAR THE SUN WILL CAUSE INSTANT AND IRREVERSIBLE DAMAGE TO YOUR EYE. EYE DAMAGE IS OFTEN PAINLESS, SO THERE IS NO WARNING TO THE OBSERVER THAT DAMAGE HAS OCCURRED UNTIL IT IS TOO LATE. DO NOT POINT THE TELESCOPE OR ITS VIEWFINDER AT OR NEAR THE SUN. DO NOT LOOK THROUGH THE TELESCOPE OR ITS VIEWFINDER AS IT IS MOVING. CHILDREN SHOULD ALWAYS HAVE ADULT SUPERVISION WHILE OBSERVING. Unlock the lock knobs: To move the telescope, you will need to unlock the horizontal lock knob (6) and vertical locking lever(5) (just rotate to unlock or lock; when locking, only tighten to a firm feel, do not overtighten). Use the red dot viewfinder: If you have not done so, align the viewfinder (2) with the telescopes eyepiece (1) as described earlier. Look through the viewfinder until you can see the object. It will be easier to locate an object using the viewfinder rather than
NEVER USE YOUR TELESCOPE TO LOOK AT THE SUN!

SUN WARNING

locating with the eyepiece. Line up the object with the viewfinders red dot.
Look through the eyepiece: Once you have the object lined up in the viewfinder, look through the optical tubes eyepiece. If you have aligned your viewfinder, you will you see the object in your eyepiece. Focus: Look through the eyepiece and practice focusing on the object you have chosen. THE MEADE 4M COMMUNITY Try out the slow motion adjustment controls: To move the telescope from side to side, first unlock the azimuth lock. Then rotate the horizontal slow motion control wheel to move the telescope from side to side.

Go to www.Meade4M.org to activate your membership today.
You havent just bought a telescope, you have embarked on an astronomy adventure that never ends. Share the journey with others by accepting your free membership in the 4M community of astronomers.
Observe the Moon: When you feel comfortable with the viewfinder, the eyepieces, the locks and the adjustment controls, you will be ready to try out the telescope at night. The Moon is the best object to observe the first time you go out at night. Pick a night when the Moon is a crescent. No shadows are seen during a full Moon, making it appear flat and uninteresting.
Can you ever have too much power? If the type of power youre referring to is eyepiece magnification, yes you can! The most common mistake of the beginning observer is to overpower a telescope by using high magnifications which the telescopes aperture and atmospheric conditions cannot reasonably support. Keep in mind that a smaller, but bright and well-resolved image is far superior to one that is larger, but dim and poorly resolved. Powers above 400x should be employed only under the steadiest atmospheric conditions.
To move the telescope up and down, unlock the altitude lock. Then rotate the altitude control wheel to move the telescope up or down.

TOO MUCH POWER?

Page 8
Observe the Solar System: After observing the Moon, you are ready to step up to the next level of observation, the planets. There are four planets that you can easily observe
Look for different features on the Moon. The most obvious features are craters. In fact you can see craters within craters. Some craters have bright lines about them. These are called rays and are the result of material thrown out of the crater when it was struck by a colliding object. The dark areas on the Moon are called maria and are composed of lava from the period when the Moon still had volcanic activity. You can also see mountain ranges and fault lines on the Moon. Use a neutral density filter (often called a moon filter) when observing the Moon. Neutral density filters are available from Meade as an optional accessory and enhance contrast to improve your observation of lunar features. Spend several nights observing the Moon. Some nights, the Moon is so bright that it makes other objects in the sky difficult to see. These are nights that are excellent for lunar observation.

Beyond the planets are clouds of comets, icy planetoids and other debris left over from the birth of our sun. Recently astronomers have found large objects in this area and they may increase the number of planets in our solar system. Venus is seen before dawn or after sunset, because it is close to the Sun. You can observe Venus going through crescent phases. But you cannot see any surface detail on Venus because it has a very thick atmosphere of gas.
The four planets closest to the Sun are rocky and are called the inner planets. Mercury, Venus, Earth and Mars comprise the inner planets. Venus and Mars can be easily seen in your telescope.
in your telescope: Venus, Mars, Jupiter and Saturn.
Nine planets (maybe more!) travel in a fairly circular pattern around our Sun. Any system of planets orbiting one or more stars is called a solar system. Our Sun, by the way, is a single, yellow dwarf star. It is average as far as stars go and is a middle aged star.
One of the most fascinating sights of Jupiter are its moons. The four largest moons are called the Galilean moons, after the astronomer Galileo, who observed them for the first time. If youve never watched the Galilean moons in your telescope before, youre missing a real treat! Each night, the moons appear in different positions around the Jovian sky. This is sometimes called the Galilean dance. On any given night, you might be able to see the shadow of a moon
When Mars is close to the Earth, you can see some details on Mars, and sometimes even Mars polar caps. But quite often, Mars is further away and just appears as a red dot with some dark lines crisscrossing it. Jupiter, Saturn, Uranus, Neptune and Pluto comprise the outer planets. These planets, except for Pluto, are made mostly of gases and are sometimes called gas giants. If they had grown much bigger, they may have become stars. Pluto is made mostly of ice. Jupiter is quite interesting to observe. You can see bands across the face of Jupiter. The more time you spend observing these bands, the more detail you will be able to see.

Page 9

Any small telescope can see the four Galilean moons of Jupiter (Fig. 5), plus a few others, but how many moons does Jupiter actually have? No one knows for sure! Nor are we sure how many Saturn has either. At last count, Jupiter had over 60 moons, and held a small lead over Saturn. Most of these moons are very small and can only be seen with very large telescopes.
on the face of Jupiter, see one moon eclipse another or even see a moon emerge from behind Jupiters giant disk. Drawing the positions of the moons each night is an excellent exercise for novice astronomers.

Fig. 5

Probably the most memorable sight you will see in your telescope is 7 Saturn. Although you may not see many features on the surface of Saturn, its ring structure will steal your breath away. You will probably be able to see a black opening in the rings, known as the Cassini band.

Saturn is not the only planet that has rings, but it is the only set of rings that can be seen with a small telescope. Jupiters rings cannot be seen from Earth at allthe Voyager spacecraft discovered the ring after it passed Jupiter and looked back at it. It
Whats Next? Beyond the Solar System: Once you have observed our own system of planets, its time to really travel far from home and look at stars and other objects.
You can observe thousands of stars with your telescope. At first, you may think stars are just pinpoints of light and arent very
Optional color filters help bring out detail and contrast of the planets. Meade offers a line of inexpensive color filters.
turns out, only with the sunlight shining through them, can the rings be seen. Uranus and Neptune also have faint rings.

Page 10

interesting. But look again. There is much information that is revealed in stars. Other stars to look for are multiple stars. Very often, you can find double (or binary) stars, stars that are very close together. These stars orbit each other. What do you notice about these stars? Are they different colors? Does one seem brighter than the other?
The first thing you will notice is that not all stars are the same colors. See if you can find blue, orange, yellow, white and red stars. The color of stars sometimes can tell you about the age of a star and the temperature that they burn at. Almost all the stars you can see in the sky are part of our galaxy. A galaxy is a large grouping of stars, containing millions or even billions of stars. Some galaxies form a spiral (like our galaxy, the Milky Way) and other galaxies look more like a large football and are called elliptical galaxies. There are many galaxies that are irregularly shaped and are thought to have been pulled apart because they passed too close toor even througha larger galaxy.
You may be able to see the Andromeda galaxy and several others in your telescope. They will appear as small, fuzzy clouds. Only very large telescope will reveal spiral or elliptical details. The more you learn about objects in the sky, the more you will learn to appreciate the sights you see in your telescope. Start a notebook and write down the observations you make each night. Note the time and the date.
You will also be able to see some nebulas with your scope. Nebula means cloud. Most nebulas are clouds of gas. The two easiest to see in the Northern Hemisphere are the Orion nebula during the winter and the Triffid nebula during the summer. These are large clouds of gas in which new stars are being born. Some nebulas are the remains of stars exploding. These explosions are called supernovas. When you become an advanced observer you can look for other types of objects such as asteroids, planetary nebula and globular clusters. And if youre lucky, every so often a bright comet appears in the sky, presenting an unforgettable sight.

Use a compass to make a circle, or trace around the lid of a jar. Draw what you see in your eyepiece inside the circle. The best exercise for drawing is to observe the moons of Jupiter every night or so. Try to make Jupiter and the moons approximately the same size as they look in your eyepiece. You will see that the moons are in a different position every night. As you get better at drawing, try more challenging sights, like a crater system on the moon or even a nebula. Go your library or check out the internet for more information about astronomy. Learn about the basics: light years, orbits, star colors, how stars and planets are formed, red shift, the big bang, what are the different kinds of nebula, what are comets, asteroids and meteors and what is a black hole. The more you learn about astronomy, the more fun, and the more rewarding your telescope will become. SOME OBSERVING TIPS Eyepieces: Always begin your observations using the 25mm low-power eyepiece. The 25mm eyepiece delivers a bright, wide field of view and is the best to use for most

Page 11

viewing conditions. Use the high-power 9mm eyepiece to view details when observing the Moon and planets. If the image become fuzzy, switch back down to a lower power. Changing eyepieces changes the power or magnification of your telescope. By the way, you might have noticed something strange when you looked through your eyepiece. Although the image is rightside up, it is reversed. That means reading words can be a problem. But it has no affect on astronomical objects. If you wish to have a fully corrected image, check out Meades optional Erecting Prism in the Optional Accessory section.

Fig. 6

barlow

eyepiece

diagonal mirror
Barlow lens: You can also change magnification by using your Barlow. 9 Remove the eyepiece from the diagonal mirror and slide in the Barlow. And then place the eyepiece into the Barlow. Tighten the thumbscrews to secure the Barlow lens and the eyepiece in place. The Barlow lens included with your telescope doubles the power of your telescope. (Fig. 6). Meade offers a complete line of eyepieces for your telescope. Most astronomers have four or five low-power and high power eyepieces to view different objects and to cope with different viewing conditions. Objects move in the eyepiece: If you are observing an astronomical object (the Moon, a planet, star, etc.) you will notice that the object will begin to move slowly through the telescopic field of view. This movement is caused by the rotation of the Earth and makes an object move through the telescopes field of view. To keep astronomical objects centered in the field, simply move the telescope on one or both of its axes vertically and/or horizontally as neededtry

Vibrations: Avoid touching the eyepiece while observing through the telescope. Vibrations resulting from such contact will
Place the object to be viewed at the edge of the field and, without touching the telescope, watch it drift through the field to the other side before repositioning the telescope so that the object to be viewed is again placed at the edge of the field, ready to be further observed.
Star charts and planispheres are useful for a variety of reasons. In particular, they are a great aid in planning a night of celestial viewing. A wide variety of star charts are available in books, in magazines, on the internet and on CD Roms. Meade offers Autostar Suite software. Contact your local Meade dealer or Meades Customer Service department for more information. Astronomy and Sky and Telescope magazines print star charts each month for up-to-the-minute maps of the heavens.
using the telescopes coarse and fine adjustment controls. At higher powers, astronomical objects will seem to move through the field of view of the eyepiece more rapidly.

STAR CHARTS

Page 12
Let your eyes dark-adapt: Allow five or ten minutes for your eyes to become dark adapted before observing. Use a redfiltered flashlight to protect your night vision when reading star maps, or inspecting the telescope. Do not use use a regular flashlight or turn on other lights when observing with a group of other astronomers. You can make your own red filtered flashlight by taping red cellophane over a flashlight lens. Viewing through windows: Avoid setting up the telescope inside a room and observing through an opened or closed window pane. Images may appear blurred or distorted due to temperature differences between inside and outside air. Also, it is a good idea to allow your telescope to reach the ambient (surrounding) outside temperature before starting an observing session. When to observe: Planets and other objects viewed low on the horizon often
cause the image to move. Avoid observing sites where vibrations cause image movement (for example, near railroad tracks). Viewing from the upper floors of a building may also cause image movement.
Dress Warm: Even on summer nights, the air can feel cool or cold as the night wears on. It is important to dress warm or to have a sweater, jacket, gloves, etc., nearby.

lack sharpnessthe same object, when observed higher in the sky, will appear sharper and have greater contrast. Try reducing power (change your eyepiece) if your image is fuzzy or shimmers. Keep in mind that a bright, clear, but smaller image is more interesting than a larger, dimmer, fuzzy one. Using too high a power eyepiece is one of the most common mistakes made by new astronomers. Know your observing site: If possible, know the location where you will be observing. Pay attention to holes in the ground and other obstacles. Is it a location where wild animals, such as skunks, snakes, etc., may appear? Are there viewing obstructions such as tall trees, street lights, headlights and so forth? The best locations are dark locations, the darker the better. Deep space objects are easiest to see under dark skies. But it is still possible to observe even in a city.
Optical tube focal length. 700mm Objective lens diameter. 60mm (2.4") Focal ratio. f/11.6 Mounting type. Altazimuth
What do the specifications mean? Optical tube focal length is simply a measurement of the length of the optical tube. In other words, this is the distance light travels in the tele-scope before being brought to focus in you eyepiece. Your tube is 700mm long. Objective lens diameter is how big the lens is on your scope. Telescopes are
Surf the Web and visit your local library: The internet contains a huge amount of astronomical information, both for children and adults. Check out astronomy books from your library. Look for star chartsthese are available on a monthly basis in Astronomy and Sky and Telescope magazines. SPECIFICATIONS ASTRONOMY IS FUN! HAVE A GOOD TIME,

Page 13

always described by how large their objective lens is. Your telescope is 60mm or 2.4 inches. Other telescopes are 90mm, 8 inches, 16 inches, or even 3 feet in diameter. The Hubble Telescopes objective lens has a diameter of 2.4 meters (thats 7.8 feet across!).
The Meade 4M Community 6001 Oak Canyon, Irvine, CA 92618 Astronomical League Executive Secretary 5675 Real del Norte, Las Cruces, NM 88012 The Astronomical Society of the Pacific 390 Ashton Avenue, San Francisco, CA 94112 The Planetary Society 65 North Catalina Avenue, Pasadena, CA 91106 International Dark-Sky Association, Inc. 3225 N. First Avenue, Tucson, AZ 85719-2103 ASTRONOMY RESOURCES
The focal ratio helps determine how fast the photographic speed of a telescope is. The lower the focal ratio number, the faster the exposure. f/5 is faster than f/10. The faster the ratio, the faster exposure time is needed when a camera is hooked up to the telescope. Your telescope has slower focal ratio at f/11.6. Sometimes, astronomers use focal

reducers to make slow exposure telescopes have faster focal ratios.
Altaz mounting simply means your telescope moves up and down (altitude or alt), and side to side, (azimuth or az). Other mounting configurations are available for other telescopes, such as equatorial mounting. USE THE SPECIFICATIONS TO CALCULATE THE MAGNIFICATION OF YOUR EYEPIECE The power of a telescope is how much it magnifies objects. Your 25mm eyepiece magnifies an object 28 times. Your 9mm eyepiece magnifies objects 78 times. Focal Length of the Telescope Focal Length of the Eyepiece = Magnification
But if you obtain other eyepieces, you can calculate how much magnification they have with your telescope. Just divide the focal length of the telescope by the focal length of the eyepiece.
Look at the specifications. You will see that the focal length of your 12 scope is 700mm. Lets say that you have obtained a 13mm eyepiece. You can tell that what the focal length of your eyepiece is as it is always printed on the side of an eyepiece. Divide: 700 13, which equals 53.8. Round this off to the nearest whole number and your new eyepiece magnifies objects 54 times.
If you use your Barlow lens with one of your eyepieces, it doubles the magnification of your eyepiece. Other types of Barlows can triple or further increase the power of an eyepiece. To find out how much your

Page 14

Your telescope is a precision optical instrument designed for a lifetime of rewarding viewing. It will rarely, if ever, require factory servicing or maintenance. Follow these guidelines to keep your telescope in the best condition:
Its worth repeating: Keep in mind that a bright, clear, but smaller image is more interesting than a larger, dimmer, fuzzy one. Using too high a power eyepiece is one of the most common mistakes made by new astronomers. So dont think that higher magnification is necessarily betterquite often the best view is with lower magnification value! TAKING CARE OF YOUR TELESCOPE
magnification is when you use a Barlow, multiply your eyepieces magnification by two. Eyepieces magnification x 2 = Magnification with a 2X Barlow lens
Your 25mm low-power eyepiece magnifies an object 28 times. Multiply 28 by 2 and you get 56 times magnification with your Barlow.

Avoid cleaning the telescopes lenses. A little dust on the front surface of the telescopes correcting lens will not cause loss of image quality. OPTIONAL ACCESSORIES #Erecting Prism (1.25 O.D.): Correctly orients the telescopic image during terrestrial observing and yields an image position at a 45 angle to the main
When absolutely necessary, dust on the front lens should be removed with very gentle strokes of a camel hair brush or blown off with an ear syringe (available at most pharmacies).
Fingerprints and organic materials on the front lens may be removed with a solution of 3 parts distilled water to 1 part isopropyl alcohol. You may also add 1 drop of biodegradable dishwashing soap per pint of solution. Use soft, white facial tissues and make short, gentle strokes. Change tissues often. CAUTION: Do not use scented or lotioned tissues or damage could result to the optics. DO NOT use a commercial photographic lens cleaner.
telescope tube, resulting in a more comfortable observing position in most cases.
Many groups also hold regularly scheduled Star Parties at which you can check out and observe with many different telescopes and other pieces of astronomical equipment. Magazines such as Sky and Telescope and Astronomy print schedules for many popular Star Parties around the United States and Canada. One of the best ways to increase your knowledge of astronomy is to join an astronomy club. Check your local newspaper, school, library, or telescope dealer/ store to find out if theres a club in your area. JOIN AN ASTRONOMY CLUB, ATTEND A STAR PARTY
Additional Eyepieces (1.25" barrel diameter): For higher or lower magnifications with the telescopes that accommodate 1.25" eyepieces, Meade Series 4000 Super Plssl eyepieces, available in a wide variety of sizes, provide a high level of image resolution and color correction at an economical price. Contact your Meade Dealer or see the Meade catalog for more information. Visit us on the web at www.meade.com.

Page 15

MEADE LIMITED WARRANTY
Every Meade telescope and telescope accessory is warranted by Meade Instruments Corporation (Meade) to be free of defects in materials and workmanship for a period of ONE YEAR from the date of original purchase in the U.S.A. Meade will repair or replace a product, or part thereof, found by Meade to be defective, provided the defective part is returned to

If you have a question concerning your telescope, call Meade Instruments Consumer Solutions Department at (800) 626-3233. Consumer Solutions Departmant hours are 8:00AM to 5:00PM, Pacific Time, Monday through Friday. Write or call the Meade Consumer Solutions Department first, before returning the telescope to the factory, giving full particulars as to the nature of the problem, as well as your name, address, and daytime telephone number. The great majority of servicing issues can be resolved by telephone, avoiding return of the telescope to the factory.

MEADE CONSUMER SOLUTIONS

Page 16
RGA Number Required: Prior to the return of any product or part, a Return Goods Authorization (RGA) number must be obtained from Meade by writing, or by calling (800) 626-3233. Each returned part or product must include a written statement detailing the nature of the claimed defect, as well as the owners name, address, and phone number. This warranty is not valid in cases where the product has been abused or mishandled, where unauthorized repairs have been attempted or performed, or where depreciation of the product is due to normal wear-and-tear. Meade specifically disclaims special, indirect, or consequential damages or lost profit which may result from a breach of this warranty. Any implied warranties which cannot be disclaimed are hereby
Meade, freight-prepaid, with proof of purchase. This warranty applies to the original purchaser only and is nontransferable. Meade products purchased outside North America are not included in this warranty, but are covered under separate warranties issued by Meade international distributors.
limited to a term of one year from the date of original retail purchase. This warranty supersedes all previous Meade product warranties.
SURF THE WEB The Meade 4M Community: http://www.meade4m.org Sky & Telescope: http://www.skyandtelescope.com Astronomy: http://www.astronomy.com Astronomy Picture of the Day: http://antwrp.gsfc.nasa.goc/apod Photographic Atlas of the Moon: http://www.lpi.ursa.edu/research/lunar_orbiter Hubble Space Telescope Public Pictures: http://oposite.stsci.edu/pubinfo/pictures.html
This warranty gives you specific rights. You may have other rights which vary from state to state. Meade reserves the right to change product specifications or to discontinue products without notice.
2006 MEADE INSTRUMENTS CORPORATION

OBSERVER: NOTES:

OBJECT NAME:
DATE & TIME OBSERVED: CONSTELLATION: EYEPIECE SIZE: SEEING CONDITIONS:

EXCELLENT

OBSERVATION LOG

Page 17

(SAVE ORIGINAL - BE SURE TO MAKE COPIES)

DRAWING OF IMAGE

Page 18

Page 19

Page 20

626-3233

Meade Instruments Corporation 6001 Oak Canyon, Irvine, California

Telestar RB-60.qxd

10/15/08

3:26 PM

Page 1

www.meade.com

MEADE INSTRUCTION MANUAL
60mm | 2.4" Altazimuth Refracting Telescope

Page 2

WARNING!
Never use a Meade Telescope to look at the Sun! Looking at or near the Sun will cause instant and irreversible damage to your eye. Eye damage is often painless, so there is no warning to the observer that damage has occurred until it is too late. Do not point the telescope at or near the Sun. Do not look through the telescope or SmartFinder as it is moving. Children should always have adult supervision while observing.

Page 3

INTRODUCTION Your telescope is an excellent beginners instrument, and is designed to observe objects in the sky and also on land. It can be your personal window on the universe or allows you to intimately study the behavior of nesting birds on a distant hillside. The telescope is shipped with the following parts: Optical tube Aluminum tripod with an accessory tray Two 1.25" eyepieces: MA25mm (28X), MH9mm (78X) 2x 1.25" Barlow lens Diagonal mirror Red dot viewfinder with bracket Telescope mount The tube has a focal length of 700mm, and its objective lens has a diameter of 60mm. The lens diameter is one of the most important pieces of information about the telescope. The size of the objective lens determines how much detail you will be able to see in your telescope. The focal length will help later on to calculate magnification. Setting up your telescope involves these simple steps: Assemble your tripod Attach the accessory tray Attach the optical tube to the mount Attach the red dot viewfinder Attach the diagonal mirror and eyepiece Align the red dot viewfinder Study the the picture on the next page and become acquainted with the parts of your telescope. Then proceed to Assemble your Tripod.

Page 4

FIGURE 1
1. Eyepiece 2. Red dot viewfinder (see Inset A) 3. Red dot viewfinder alignment screws (see Inset A) 4. Optical tube assembly 5. Vertical locking lever 6. Horizontal lock knob 7. Tripod legs 8. Leg brace supports (See Inset C) 9. Leg brace (See Inset C) 10. Mount base attachment 11. Optical tube lock knobs 12. Horizontal slow motion controll (See Inset B) 13. Diagonal mirror 14. Objective lens cell 15. Focuser drawtube 16. Vertical slow motion control (See Inset B) 17. Accessory tray (Inset C) 18. Red dot viewfinder bracket (see Inset A) 19. Adjustable sliding leg extension (see Inset C) 20. Tripod leg lock (see Inset C) 21. Dew shield/lens shade 22. Front lens cap (removed) 23. Focusing knob 24. Single arm mechanism
Figure 1: Meade 60-RB Altazimuth Refracting Telescope Inset A: Red Dot Viewfinder Assembly Inset B: Tripod Legs and Accessory Tray Inset C: Altaz or Azimuth Mount

Inset A

Inset B

Inset C

(Not visible)

Page 5

ASSEMBLE YOUR TRIPOD The tripod is the basic support for your telescope. Its height may be adjusted so that you can view comfortably. Note: Number in brackets, e.g., (3), refer to Fig. 1. 1. Spread the legs out evenly apart. 2. Set the height of your tripod unlock the leg lock (20). 3. Slide leg (19) in or out to the desired length Inset B 4. Tighten the leg lock (20) to relock the leg lock. 5. Repeat for the other two legs. ATTACH THE ACCESSORY TRAY The tray helps stabilize the tripod and is also a convenient holder of eyepieces and other Meade accessories, such as the Barlow lens. 1. Place the accessory tray (17) over the center of the leg brace supports (8). 2. Rotate the tray so it fits onto the central

Fig. 2

ATTACH THE RED DOT VIEWFINDER An eyepiece (1) has a narrow field of 3 view. A viewfinder (2) has a wider field of view, which makes it easier to locate objects. The red dot viewfinder has a red dot to make it easier to line up more precisely with a target. 1. Note the red dot viewfinder (2) has a quick release mounting bracket (18). 2. Slide the red dot viewfinder (2) into the Fig. 3 mounting bracket as shown on Fig. 3. Note: To detach the bracket press the bracket quick release button and slide the bracket out. ATTACH THE DIAGONAL MIRROR AND EYEPIECE The diagonal mirror reflects the light from the optical tube to a more comfortable viewing position. 1. Slide the diagonal mirror (13) into the focuser drawtube(15).
lock. See Inset B. 3. Rotate the tray, locking the corners of the tray in place on the leg brace supports. ATTACH THE OPTICAL TUBE TO THE MOUNT The optical tube gathers distant light which is focused in the eyepiece. 1. Remove the two lock knobs (11) from the optical tube. 2. Slide the altitude rod into the hole in the altitude adjustment control. Tighten to a firm feel. See Fig. 2. 3. Place the optical tube (4) onto the mounting bracket Fig. 2. 4. Thread a lock knob (11) onto each of the mounting screws and tighten to a firm feel. See Fig. 2.
Looking at or near the Sun will cause irreversible damage to your eye. Do not point this telescope at or near the Sun. Do not look through the telescope as it is moving.

Page 6

2. Tighten the drawtube thumbscrew to hold the diagonal mirror securely. 4 3. Slide the MA 25mm eyepiece (1) into diagonal mirror (13). 4. Tighten the diagonal mirror thumbscrew (26) to hold the eyepiece securely. ALIGN THE RED DOT VIEWFINDER Perform the first part of this procedure during the daytime and the last step at night. 1. Point the telescope at an easy-to-find land object such as the top of a telephone pole or a distant mountain or tower. Look through the eyepiece in the diagonal mirror and turn the focuser knob (23) until the image is sharply focused. Center the object precisely in the eyepieces field of view. 2. Look through the red dot viewfinder. Turn one or more of the viewfinders alignment screws (3) until the red dot is precisely over the same object as you centered in the eyepiece. 3. Check this alignment at night on a celestial object, such as the Moon or a bright star, and use the viewfinders
alignment screws to make any necessary refinements. TO MOVE THE TELESCOPE Your telescope is altazimuth mounted. Altazimuth is just a complicated way of saying that your telescope moves up and down and from side to side. Other telescopes may be mounted in different ways. 1. Slightly loosen the vertical locking lever (5). Loosening this lever allows you to move the telescope up and down. 2. Slightly loosen the horizontal lock knob (6). Loosening this lock allows the telescope to be moved from side to side. 3. Once an object is found, re-tighten the knob. You can then use the slow motion controls to make smooth and precise movements as you follow (or track) an object as it moves in the eyepiece. You will enjoy your telescope even more as you learn more about it. But dont be scared off by difficult terms or complicated procedures. Dont panic! Just relax and enjoy your scope.

THE MOST IMPORTANT RULE We have one very important rule that you should always follow when using your telescope:

Have Fun!

Have a good time when youre observing. You may not know everything that there is to know about a telescope or what all the sights in the universe are, but thats OK. Just point and observe at first. You will begin to grow and learn more about astronomy the more you observe. Go to the

Page 7

library and read some books about the stars and planets. Read about astronomers of old. Many of them had telescope no bigger than the one you are using right now. Galileo, who is one of the first astronomers to use a telescope, discovered four of the moons of Jupiter with a telescope about the same size as yours (and his didnt even focus very well!). OBSERVING Observe during the daytime: Try out your telescope during the daytime at first. It is easier to learn how it operates and how to observe when it is light. Pick out an easy object to observe: A distant mountain, a large tree, a lighthouse or skyscraper make excellent targets. Point the optical tube so it lines up with your object. Unlock the lock knobs: To move the telescope, you will need to unlock the horizontal lock knob (6) and vertical locking lever(5) (just rotate to unlock or lock; when locking, only tighten to a firm feel, do not overtighten).

SUN WARNING

NEVER USE YOUR TELESCOPE TO LOOK AT THE SUN! LOOKING AT OR NEAR THE SUN WILL CAUSE INSTANT AND IRREVERSIBLE DAMAGE TO YOUR EYE. EYE DAMAGE IS OFTEN PAINLESS, SO THERE IS NO WARNING TO THE OBSERVER THAT DAMAGE HAS OCCURRED UNTIL IT IS TOO LATE. DO NOT POINT THE TELESCOPE OR ITS VIEWFINDER AT OR NEAR THE SUN. DO NOT LOOK THROUGH THE TELESCOPE OR ITS VIEWFINDER AS IT IS MOVING. CHILDREN SHOULD ALWAYS HAVE ADULT SUPERVISION WHILE OBSERVING.
Focus: Look through the eyepiece and practice focusing on the object you have chosen.
Try out the slow motion adjustment controls: Practice using the slow motion controls (12 and 16) to move the telescope. These can come in very handy, especially when you wish to move the telescope in very small (fine control) steps. Observe the Moon: When you feel comfortable with the viewfinder, the eyepieces, the locks and the adjustment controls, you will be ready to try out the telescope at night. The Moon is the best object to observe the first time you go out at night. Pick a night when the Moon is a THE MEADE 4M COMMUNITY
You havent just bought a telescope, you have embarked on an astronomy adventure that never ends. Share the journey with others by accepting your free membership in the 4M community of astronomers. Go to www.Meade4M.org to activate your membership today.

Use the red dot viewfinder: If you have not done so, align the viewfinder (2) with the telescopes eyepiece (1) as described earlier. Look through the viewfinder until you can see the object. It will be easier to locate an object using the viewfinder rather than locating with the eyepiece. Line up the object with the viewfinders red dot. Look through the eyepiece: Once you have the object lined up in the viewfinder, look through the optical tubes eyepiece. If you have aligned your viewfinder, you will you see the object in your eyepiece.

Page 8

crescent. No shadows are seen during a full Moon, making it appear flat and uninteresting.
volcanic activity. You can also see mountain ranges and fault lines on the Moon. Use a neutral density filter (often called a moon filter) when observing the Moon. Neutral density filters are available from Meade as an optional accessory and enhance contrast to improve your observation of lunar features. Spend several nights observing the Moon. Some nights, the Moon is so bright that it makes other objects in the sky difficult to see. These are nights that are excellent for lunar observation. Observe the Solar System: After observing the Moon, you are ready to step up to the next level of observation, the planets. There are four planets that you can easily observe in your telescope: Venus, Mars, Jupiter and Saturn. Nine planets (maybe more!) travel in a fairly circular pattern around our Sun. Any system of planets orbiting one or more stars is called a solar system. Our Sun, by the way,
is a single, yellow dwarf star. It is average as far as stars go and is a middle aged star. Beyond the planets are clouds of comets, icy planetoids and other debris left over from the birth of our sun. Recently astronomers have found large objects in this area and they may increase the number of planets in our solar system. The four planets closest to the Sun are rocky and are called the inner planets. Mercury, Venus, Earth and Mars comprise the inner planets. Venus and Mars can be easily seen in your telescope. Venus is seen before dawn or after sunset, because it is close to the Sun. You can observe Venus going through crescent phases. But you cannot see any surface detail on Venus because it has a very thick atmosphere of gas. When Mars is close to the Earth, you can see some details on Mars, and sometimes even Mars polar caps. But quite often, Mars is further away and just appears as a red dot with some dark lines crisscrossing it.

Look for different features on the Moon. The most obvious features are craters. In fact you can see craters within craters. Some craters have bright lines about them. These are called rays and are the result of material thrown out of the crater when it was struck by a colliding object. The dark areas on the Moon are called maria and are composed of lava from the period when the Moon still had
TOO MUCH POWER? Can you ever have too much power? If the type of power youre referring to is eyepiece magnification, yes you can! The most common mistake of the beginning observer is to overpower a telescope by using high magnifications which the telescopes aperture and atmospheric conditions cannot reasonably support. Keep in mind that a smaller, but bright and well-resolved image is far superior to one that is larger, but dim and poorly resolved. Powers above 400x should be employed only under the steadiest atmospheric conditions.

Page 9

Jupiter, Saturn, Uranus, Neptune and Pluto comprise the outer planets. These planets, except for Pluto, are made mostly of gases and are sometimes called gas giants. If they had grown much bigger, they may have become stars. Pluto is made mostly of ice. Jupiter is quite interesting to observe. You can see bands across the face of Jupiter. The more time you spend observing these bands, the more detail you will be able to see. One of the most fascinating sights of Jupiter are its moons. The four largest moons are called the Galilean moons, after the astronomer Galileo, who observed them for the first time. If youve never watched the Galilean moons in your telescope before, youre missing a real treat! Each night, the moons appear in different positions around the Jovian sky. This is sometimes called the Galilean dance. On any given night, you might be able to see the shadow of a moon on the face of Jupiter, see one moon eclipse another or even see a moon emerge from behind Jupiters giant disk. Drawing the positions of the moons each night is an

Fig. 5

a black opening in the rings, known as the Cassini band.
excellent exercise for novice astronomers. Any small telescope can see the four Galilean moons of Jupiter (Fig. 5), plus a few others, but how many moons does Jupiter actually have? No one knows for sure! Nor are we sure how many Saturn has either. At last count, Jupiter had over 60 moons, and held a small lead over Saturn. Most of these moons are very small and can only be seen with very large telescopes. Probably the most memorable sight you will see in your telescope is Saturn. Although you may not see many features on the surface of Saturn, its ring structure will steal your breath away. You will probably be able to see

Saturn is not the only planet that has rings, but it is the only set of rings that can be seen with a small telescope. Jupiters rings cannot be seen from Earth at allthe Voyager spacecraft discovered the ring after it passed Jupiter and looked back at it. It turns out, only with the sunlight shining through them, can the rings be seen. Uranus and Neptune also have faint rings. Optional color filters help bring out detail and contrast of the planets. Meade offers a line of inexpensive color filters.

Page 10

Whats Next? Beyond the Solar System: Once you have observed our 8 own system of planets, its time to really travel far from home and look at stars and other objects. You can observe thousands of stars with your telescope. At first, you may think stars are just pinpoints of light and arent very interesting. But look again. There is much information that is revealed in stars. The first thing you will notice is that not all stars are the same colors. See if you can find blue, orange, yellow, white and red stars.
The color of stars sometimes can tell you about the age of a star and the temperature that they burn at. Other stars to look for are multiple stars. Very often, you can find double (or binary) stars, stars that are very close together. These stars orbit each other. What do you notice about these stars? Are they different colors? Does one seem brighter than the other? Almost all the stars you can see in the sky are part of our galaxy. A galaxy is a large grouping of stars, containing millions or even billions of stars. Some galaxies form a spiral (like our galaxy, the Milky Way) and other galaxies look more like a large football and are called elliptical galaxies. There are many galaxies that are irregularly shaped and are thought to have been pulled apart because they passed too close toor even througha larger galaxy. You may be able to see the Andromeda galaxy and several others in your telescope. They will appear as small, fuzzy clouds. Only
very large telescope will reveal spiral or elliptical details. You will also be able to see some nebulas with your scope. Nebula means cloud. Most nebulas are clouds of gas. The two easiest to see in the Northern Hemisphere are the Orion nebula during the winter and the Triffid nebula during the summer. These are large clouds of gas in which new stars are being born. Some nebulas are the remains of stars exploding. These explosions are called supernovas. When you become an advanced observer you can look for other types of objects such as asteroids, planetary nebula and globular clusters. And if youre lucky, every so often a bright comet appears in the sky, presenting an unforgettable sight. The more you learn about objects in the sky, the more you will learn to appreciate the sights you see in your telescope. Start a notebook and write down the observations you make each night. Note the time and the date.

Page 11

Use a compass to make a circle, or trace around the lid of a jar. Draw what you see in your eyepiece inside the circle. The best exercise for drawing is to observe the moons of Jupiter every night or so. Try to make Jupiter and the moons approximately the same size as they look in your eyepiece. You will see that the moons are in a different position every night. As you get better at drawing, try more challenging sights, like a crater system on the moon or even a nebula. Go your library or check out the internet for more information about astronomy. Learn about the basics: light years, orbits, star colors, how stars and planets are formed, red shift, the big bang, what are the different kinds of nebula, what are comets, asteroids and meteors and what is a black hole. The more you learn about astronomy, the more fun, and the more rewarding your telescope will become. SOME OBSERVING TIPS Eyepieces: Always begin your observations using the 25mm low-power eyepiece. The 25mm eyepiece delivers a bright, wide field

Fig. 6

eyepiece barlow
optional Erecting Prism in the Optional Accessory section.
diagonal mirror of view and is the best to use for most viewing conditions. Use the high-power 9mm eyepiece to view details when observing the Moon and planets. If the image become fuzzy, switch back down to a lower power. Changing eyepieces changes the power or magnification of your telescope. By the way, you might have noticed something strange when you looked through your eyepiece. Although the image is rightside up, it is reversed. That means reading words can be a problem. But it has no affect on astronomical objects. If you wish to have a fully corrected image, check out Meades
Barlow lens: You can also change magnification by using your Barlow. Remove the eyepiece from the diagonal mirror and slide in the Barlow. And then place the eyepiece into the Barlow. Tighten the thumbscrews to secure the Barlow lens and the eyepiece in place. The Barlow lens included with your telescope doubles the power of your telescope. See Fig. 6. Meade offers a complete line of eyepieces for your telescope. Most astronomers have four or five low-power and high power eyepieces to view different objects and to cope with different viewing conditions. Objects move in the eyepiece: If you are observing an astronomical object (the Moon, a planet, star, etc.) you will notice that the object will begin to move slowly through the telescopic field of view. This movement is caused by the rotation of the Earth and makes an object move through the telescopes field of view. To keep astronomical

Page 12

objects centered in the field, simply move the telescope on one or both of 10 its axesvertically and/or horizontally as neededtry using the telescopes coarse and fine adjustment controls. At higher powers, astronomical objects will seem to move through the field of view of the eyepiece more rapidly. Place the object to be viewed at the edge of the field and, without touching the telescope, watch it drift through the field to the other side before repositioning the telescope so that the object to be viewed is
STAR CHARTS Star charts and planispheres are useful for a variety of reasons. In particular, they are a great aid in planning a night of celestial viewing. A wide variety of star charts are available in books, in magazines, on the internet and on CD Roms. Meade offers Autostar Suite software. Contact your local Meade dealer or Meades Customer Service department for more information.
again placed at the edge of the field, ready to be further observed. Vibrations: Avoid touching the eyepiece while observing through the telescope. Vibrations resulting from such contact will cause the image to move. Avoid observing sites where vibrations cause image movement (for example, near railroad tracks). Viewing from the upper floors of a building may also cause image movement. Let your eyes dark-adapt: Allow five or ten minutes for your eyes to become dark adapted before observing. Use a redfiltered flashlight to protect your night vision when reading star maps, or inspecting the telescope. Do not use use a regular flashlight or turn on other lights when observing with a group of other astronomers. You can make your own red filtered flashlight by taping red cellophane over a flashlight lens. Viewing through windows: Avoid setting up the telescope inside a room and observing through an opened or closed window pane. Images may appear blurred or distorted due
to temperature differences between inside and outside air. Also, it is a good idea to allow your telescope to reach the ambient (surrounding) outside temperature before starting an observing session. When to observe: Planets and other objects viewed low on the horizon often lack sharp-nessthe same object, when observed higher in the sky, will appear sharper and have greater contrast. Try reducing power (change your eyepiece) if your image is fuzzy or shimmers. Keep in mind that a bright, clear, but smaller image is more interesting than a larger, dimmer, fuzzy one. Using too high a power eyepiece is one of the most common mistakes made by new astronomers. Dress Warm: Even on summer nights, the air can feel cool or cold as the night wears on. It is important to dress warm or to have a sweater, jacket, gloves, etc., nearby. Know your observing site: If possible, know the location where you will be observing. Pay attention to holes in the ground and other

Astronomy and Sky and Telescope magazines print star charts each month for up-to-the-minute maps of the heavens.

Page 13

obstacles. Is it a location where wild animals, such as skunks, snakes, etc., may appear? Are there viewing obstructions such as tall trees, street lights, headlights and so forth? The best locations are dark locations, the darker the better. Deep space objects are easiest to see under dark skies. But it is still possible to observe even in a city. Surf the Web and visit your local library: The internet contains a huge amount of astronomical information, both for children and adults. Check out astronomy books from your library. Look for star chartsthese are available on a monthly basis in Astronomy and Sky and Telescope magazines. HAVE A GOOD TIME, ASTRONOMY IS FUN! SPECIFICATIONS Optical tube focal length. 700mm Objective lens diameter. 60mm (2.4") Focal ratio. f/11.6 Mounting type. Altazimuth
What do the specifications mean? Optical tube focal length is simply a measurement of the length of the optical tube. In other words, this is the distance light travels in the tele-scope before being brought to focus in you eyepiece. Your tube is 700mm long. Objective lens diameter is how big the lens is on your scope. Telescopes are always described by how large their objective lens is. Your telescope is 60mm or 2.4 inches. Other telescopes are 90mm, 8 inches, 16 inches, or even 3 feet in diameter. The Hubble Telescopes objective lens has a diameter of 2.4 meters (thats 7.8 feet across!). The focal ratio helps determine how fast the photographic speed of a telescope is. The lower the focal ratio number, the faster the exposure. f/5 is faster than f/10. The faster the ratio, the faster exposure time is needed when a camera is hooked up to the telescope. Your telescope has slower focal ratio at f/11.6. Sometimes, astronomers use focal reducers to make slow exposure telescopes have faster focal ratios.
Altaz mounting simply means your telescope moves up and down (altitude 11 or alt), and side to side, (azimuth or az). Other mounting configurations are available for other telescopes, such as equatorial mounting. USE THE SPECIFICATIONS TO CALCULATE THE MAGNIFICATION OF YOUR EYEPIECE The power of a telescope is how much it magnifies objects. Your 25mm eyepiece magnifies an object 28 times. Your 9mm eyepiece magnifies objects 78 times.
ASTRONOMY RESOURCES The Meade 4M Community 6001 Oak Canyon, Irvine, CA 92618 Astronomical League Executive Secretary 5675 Real del Norte, Las Cruces, NM 88012 The Astronomical Society of the Pacific 390 Ashton Avenue, San Francisco, CA 94112 The Planetary Society 65 North Catalina Avenue, Pasadena, CA 91106 International Dark-Sky Association, Inc. 3225 N. First Avenue, Tucson, AZ 85719-2103

Page 14

But if you obtain other eyepieces, you can calculate how much magnification 12 they have with your telescope. Just divide the focal length of the telescope by the focal length of the eyepiece. Focal Length of the Telescope Focal Length of the Eyepiece = Magnification Look at the specifications. You will see that the focal length of your scope is 700mm. Lets say that you have obtained a 13mm

eyepiece. You can tell that what the focal length of your eyepiece is as it is always printed on the side of an eyepiece. Divide: 700 13, which equals 53.8. Round this off to the nearest whole number and your new eyepiece magnifies objects 54 times. If you use your Barlow lens with one of your eyepieces, it doubles the magnification of your eyepiece. Other types of Barlows can triple or further increase the power of an eyepiece. To find out how much your magnification is when you use a Barlow, multiply your eyepieces magnification by two. Eyepieces magnification x 2 = Magnification with a 2X Barlow lens Your 25mm low-power eyepiece magnifies an object 28 times. Multiply 28 by 2 and you get 56 times magnification with your Barlow. Its worth repeating: Keep in mind that a bright, clear, but smaller image is more interesting than a larger, dimmer, fuzzy one. Using too high a power eyepiece is one of the most common mistakes made by new astronomers. So dont think that higher
magnification is necessarily betterquite often the best view is with lower magnification value! TAKING CARE OF YOUR TELESCOPE Your telescope is a precision optical instrument designed for a lifetime of rewarding viewing. It will rarely, if ever, require factory servicing or maintenance. Follow these guidelines to keep your telescope in the best condition: Avoid cleaning the telescopes lenses. A little dust on the front surface of the telescopes correcting lens will not cause loss of image quality.
JOIN AN ASTRONOMY CLUB, ATTEND A STAR PARTY One of the best ways to increase your knowledge of astronomy is to join an astronomy club. Check your local newspaper, school, library, or telescope dealer/ store to find out if theres a club in your area. Many groups also hold regularly scheduled Star Parties at which you can check out and observe with many different telescopes and other pieces of astronomical equipment. Magazines such as Sky and Telescope and Astronomy print schedules for many popular Star Parties around the United States and Canada.

Page 15

When absolutely necessary, dust on the front lens should be removed with very gentle strokes of a camel hair brush or blown off with an ear syringe (available at most pharmacies). Fingerprints and organic materials on the front lens may be removed with a solution of 3 parts distilled water to 1 part isopropyl alcohol. You may also add 1 drop of biodegradable dishwashing soap per pint of solution. Use soft, white facial tissues and make short, gentle strokes. Change tissues often. CAUTION: Do not use scented or lotioned tissues or damage could result to the optics. DO NOT use a commercial photographic lens cleaner. OPTIONAL ACCESSORIES #Erecting Prism (1.25 O.D.): Correctly orients the telescopic image during terrestrial observing and yields an image position at a 45 angle to the main telescope tube, resulting in a more comfor-table observing position in most cases.

Additional Eyepieces (1.25" barrel diameter): For higher or lower magnifications with the telescopes that accommodate 1.25" eyepieces, Meade Series 4000 Super Plssl eyepieces, available in a wide variety of sizes, provide a high level of image resolution and color correction at an economical price. Contact your Meade Dealer or see the Meade catalog for more information. Visit us on the web at www.meade.com.

Page 16

MEADE CONSUMER SOLUTIONS a question concerning 14 If you have call Meade Instrumentsyour telescope, Consumer Solutions Department at (800) 626-3233. Consumer Solutions Departmant hours are 8:00AM to 5:00PM, Pacific Time, Monday through Friday. Write or call the Meade Consumer Solutions Department first, before returning the telescope to the factory, giving full particulars as to the nature of the problem, as well as your name, address, and daytime telephone number. The great majority of servicing issues can be resolved by telephone, avoiding return of the telescope to the factory. MEADE LIMITED WARRANTY Every Meade telescope and telescope accessory is warranted by Meade Instruments Corporation (Meade) to be free of defects in materials and workmanship for a period of ONE YEAR from the date of original purchase in the U.S.A. Meade will repair or replace a product, or part thereof, found by Meade to be defective, provided the defective part is
returned to Meade, freight-prepaid, with proof of purchase. This warranty applies to the original purchaser only and is nontransferable. Meade products purchased outside North America are not included in this warranty, but are covered under separate warranties issued by Meade international distributors. RGA Number Required: Prior to the return of any product or part, a Return Goods Authorization (RGA) number must be obtained from Meade by writing, or by calling (800) 626-3233. Each returned part or product must include a written statement detailing the nature of the claimed defect, as well as the owners name, address, and phone number. This warranty is not valid in cases where the product has been abused or mishandled, where unauthorized repairs have been attempted or performed, or where depreciation of the product is due to normal wear-and-tear. Meade specifically disclaims special, indirect, or consequential damages or lost profit which may result from a breach of this warranty. Any implied warranties

which cannot be disclaimed are hereby limited to a term of one year from the date of original retail purchase. This warranty gives you specific rights. You may have other rights which vary from state to state. Meade reserves the right to change product specifications or to discontinue products without notice.
This warranty supersedes all previous Meade product warranties.
2006 MEADE INSTRUMENTS CORPORATION
SURF THE WEB The Meade 4M Community: http://www.meade4m.org Sky & Telescope: http://www.skyandtelescope.com Astronomy: http://www.astronomy.com Astronomy Picture of the Day: http://antwrp.gsfc.nasa.goc/apod Photographic Atlas of the Moon: http://www.lpi.ursa.edu/research/lunar_orbiter Hubble Space Telescope Public Pictures: http://oposite.stsci.edu/pubinfo/pictures.html

Page 17

OBSERVATION LOG OBSERVER: OBJECT NAME: DATE & TIME OBSERVED: CONSTELLATION: EYEPIECE SIZE: SEEING CONDITIONS: NOTES: EXCELLENT GOOD POOR

DRAWING OF IMAGE

(SAVE ORIGINAL - BE SURE TO MAKE COPIES)

3:27 PM

Page 18

Page 19

Page 20

Page 21

Page 22

Page 23

Page 24

626-3233

Meade Instruments Corporation 6001 Oak Canyon, Irvine, California