ii AK53 D.O.C. Service Manual 22/03/2004

1.INTRODUCTION

11AK53 is a 100Hz color television DIGITAL ONE CHIP SYSTEM (DOC) capable of driving 284:3/16:9 SF/RF, 294:3 real flat, 32 16:9 SF/RF, 334:3 and 34 4:3 real flat picture tubes. The chassis is capable of operation in PAL, SECAM, NTSC (playback) color standards and multiple transmission standards as B/G, D/K, I/I, and L/L. Sound system output is supplying 2x10W (10%THD) for left and right outputs of 8ohm speakers. TV supports the level 1.5 teletext standard. It is possible to decode transmissions including high graphical data. The chassis is equipped with two full EuroScarts, one SCART for AV input/output, one front-AV input, one back-AV input, one headphone output, one SVHS input (via SCART and SVHS connector), two external speaker outputs (left and right), one audio line output.

2.TUNER SPECIFICATION

The hardware and software of the TV is suitable for tuners, supplied by different companies, which are selected from the Service Menu. These tuners can be combined VHF, UHF tuners suitable for CCIR 2 systems B/G, H, L, L, I/I, and D/K. The tuning is available through the digitally controlled I C bus (PLL). Below you will find info on one of the Tuners in use. General description of UV1316 MK3(Philips) /CTF55XX (Thomson): UV1316 MK3 (Philips) /CTF55XX (Thomson) tuners, which are designed to meet a wide range of applications are PLL tuners; It is a combined VHF, UHF tuner suitable for CCIR systems B/G, H, L, L, I and I. The low IF output impedance has been designed for direct drive of a wide variety of SAW filters with sufficient suppression of triple transient. Features of Tuner: 1. Those tuners are small sized UHF/VHF tuners 2. Systems CCIR: B/G, H, L, L, I and I; OIRT: D/K 2 3. Digitally controlled (PLL) tuning via I C-bus 4. Off-air channels, S-cable channels and Hyperband 5. World standardized mechanical dimensions and world standard pinning 6. Compact size 7. Complies to CENELEC EN55020 and EN55013 Pinning: 1. Gain control voltage (AGC) 2. Tuning voltage 3. IC-bus address select 4. IC-bus serial clock 5. IC-bus serial data 6. Not connected 7. PLL supply voltage 8. ADC input 9. Tuner supply voltage* 10. Symmetrical IF output 1 11. Symmetrical IF output 2 : : : : : : 4.0V, Max: 4.5V Max: 5.5V Min:-0.3V, Max: 5.5V Min:-0.3V, Max: 5.5V 5.0V, Min: 4.75V, Max: 5.5V 33V, Min: 30V, Max: 35V
*33V is obtained from FBT of large signal board.
1 AK53 D.O.C. Service Manual 22/03/2004
3.IF/AUDIO&VIDEO SWITCHING/AD CONVERTER PART (PNX3000 (CALLED AS MPIF))
MPIF IC consists of following OVERALL blocks; (1)-Video/Audio switching (2)-IF processing (3)-A/D conversion for digital TV (DTV) processor (ADOC-PNX300X) Main building blocks: _ Vision PLL-IF, auto-calibrated, selectable IF frequency, 4 selectable AGC time constants, built-in sound trap and selectable group delay. The demodulated CVBS signal is fed outside for use with SCART. _ Synthesizer mode, meant for down mixing of DTV signals to a suitable 2nd IF which can be handled by a digital DTV decoder. Using a suitable SAW filter at the input the synthesizer mode can also be used to downmix FM radio frequencies from the Tuner to a suitable 2nd IF frequency for the FM demodulator. _ Two Video IF inputs, selectable by internal switch to enable use of optimized SAW filters _ Sound QSS IF, demodulated 2nd SIF can be either from SIF input (QSS) or Video IF (intercarrier). The Sound IF also contains an AM demodulator for SECAM L/L' _ CVBS and Y/C crossbar switch, with 2 video outputs for further processing in the Digital TV Signal Processor after A/D conversion and 2 selectable video outputs which are available on output pins for external connections 2 AK53 D.O.C. Service Manual 22/03/2004

5 AK53 D.O.C. Service Manual 22/03/2004
11.SAW FILTER SPECIFICATION
Two groups of saw filters are used from EPCOS For picture (Z400) ? Pal Secam BG DK L L?K3953M ? Pal Secam BG I I ?K3953M For sound(Z401) ? Pal Secam BG DK L L?K9656M ? Pal Secam BG I I ?K9356 For sound saw filter it needs to be switched between L and other standards for K3953M, a port signal coming from PNX300X(ADOC) called SEL_L/L is used for this purpose to make pin2 of audio saw filter ground or not. port state Q404 SEL_L/L' High Shorted to ground SEL_L/L' Low open Pin Configuration Pin No 5 Definition Input Input - ground Chip carrier - ground Output Output Standard L' BG,DK,I,L
Maximum ratings for saw filters Operable temperature range Storage temperature range DC voltage AC voltage TA Tstg VDC Vpp 25/+65 C

12.IC DESCRIPTIONS

In following chapters you can find details of ICs used in the chassis and the SS B(Small signal board) TDA6108JF PNX3000 SDRAM 64MBIT NE56610-29 PNX300X TDA7480L TDA8177&STV9379FA MC44608 TFMS5360 HT48RA0A CS51033 FLASH 32 MBIT STS5PF30L M24C64WBN6 LM7808 TCET1102G TL431
6 AK53 D.O.C. Service Manual 22/03/2004
12.1.TDA6108JF (IC900) 12.1.1.General Description The TDA6108JF includes three video output amplifiers in one plastic DIL-bent-SIL 9-pin medium power (DBS9MPF) package (SOT111-1), using high-voltage DMOS technology, and is intended to drive the three cathodes of a color CRT directly. To obtain maximum performance, the amplifier should be used with blackcurrent control. 12.1.2.Features Typical bandwidth of 9.0 MHz for an output signal of 60 V (p-p) High slew rate of 1850 V/ms No external components required Very simple application Single supply voltage of 200 V Internal reference voltage of 2.5 V Fixed gain of 51 Black-Current Stabilization (BCS) circuit Thermal protection 12.1.3.Pinning SYMBOL Vi(1) Vi(2) Vi(3) GND Iom VDD Voc(3) Voc(2) Voc(1) PIN 9 DESCRIPTION inverting input 1 inverting input 2 inverting input 3 ground (fin) black current measurement output supply voltage cathode output 3 cathode output 2 cathode output 1
7 AK53 D.O.C. Service Manual 22/03/2004
12.2.HT48RA0A 12.2.1.General Description The HT48RA0A is an 8-bit high performance RISC-like microcontroller specifically designed for multiple I/O product applications. The device is particularly suitable for use in products such as infrared remote controllers and various subsystem controllers. A HALT feature is included to reduce power consumption. 12.2.2.Features Operating voltage: 2.2V~3.6V Ten bidirectional I/O lines Six Schmitt trigger input lines One carrier output (1/2 or 1/3 duty) On-chip crystal and RC oscillator Watchdog Timer 1K_14 program EPROM 32_8 data RAM HALT function and wake-up feature reduce power consumption 62 powerful instructions Up to 1_s instruction cycle with 4MHz system clock All instructions in 1 or 2 machine cycles 14-bit table read instructions One-level subroutine nesting Bit manipulation instructions 20-pin/24-pin SOP package 12.2.3.Pin Descriptions Pin Name PB0, PB1 I/O I/O Code Option Wake-up or None Description 2-bit bidirectional input/output lines with pull-high resistors. Each bit can be determined as NMOS output or Schmitt trigger input by software instructions. Each bit can also be configured as wake-up input by code option. Level or carrier output pin PC0 can be set as CMOS output pin or carrier output pin by code option. Positive power supply OSC1, OSC2 are connected to an RC network or a crystal (determined by code option) for the internal system clock. In the case of RC operation, OSC2 is the output terminal for 1/4 system clock (NMOS open drain output). Negative power supply, ground Schmitt trigger reset input. Active low. 6-bit Schmitt trigger input lines with pull-high resistors. Each bit can be configured as a wake-up input by code option. Bidirectional 8-bit input/output port with pull-high resistors. Each bit can be determined as NMOS output or Schmitt trigger input by software instructions.

11 AK53 D.O.C. Service Manual 22/03/2004
DTVOUTN VCC_SUP fuse CVBSOUTIF GND_SUP VCC1_VSW CVBS0 TESTPIN1 VCC2_VSW CVBS1 R5 L5

127 128

DTV output negative supply of supply circuit (5V) fused lead CVBS output of IF circuit ground of supply circuit supply of video switch (5V) CVBS0 input (to be used for CVBS from IF part) test pin 1 (connect to ground) supply of video switch (5V) CVBS1 input right input audio 5 left input audio 5
Important pins need to be checked in case of troubleshooting Signal CVBS/RGB Input voltage CVBS Output voltage Maximum input audio voltage Maximum output audio voltage Measure Input pins Output pins Input pins Output pins Value 1Vpk-pk 2 Vpk-pk 2 Vrms 2 Vrms
12 AK53 D.O.C. Service Manual 22/03/2004
12.4.CS51033 (IC 104) 12.4.1.General Description The CS51033 is a switching controller for use in dcdc converters. It can be used in the buck topology with a minimum number of external components. The CS51033 consists of a 1.0 A power driver for controlling the gate of a discrete Pchannel transistor, fixed frequency oscillator, short circuit protection timer, programmable Soft Start, precision reference, fast output voltage monitoring comparator, and output stage driver logic with latch. The high frequency oscillator allows the use of small inductors and output capacitors, minimizing PC board area and systems cost. The programmable Soft Start reduces current surges at start u The p. short circuit protection timer significantly reduces the PFET duty cycle to approximately 1/30 of its normal cycle during short circuit conditions. The CS51033 is available in an 8Lead SO package. 12.4.2.Features 1.0 A Totem Pole Output Driver High Speed Oscillator (700 kHz max) No Stability Compensation Required Lossless Short Circuit Protection 2.0% Precision Reference Programmable Soft Start Wide Ambient Temperature Range: Industrial Grade: 40C to 85C Commercial Grade: 0C to 70C 12.4.3.Pin Description PIN NUMBER PIN SYMBOL VGATE PGND COSC GND VFB VCC CS VC FUNCTION Driver pin to gate of external PFET. Output power stage ground connection. Oscillator frequency programming capacitor. Logic ground. Feedback voltage input. Logic supply voltage. Soft Start and fault timing capacitor. Driver supply voltage.

13 AK53 D.O.C. Service Manual 22/03/2004
12.5.SDRAM 64MBIT (IC315) 12.5.1.General Description Please note that in the following explanation one of the SDRAM alternative is used. The K4S641632D is 67,108,864 bits synchronous high data rate Dynamic RAM organized as 4 x 1,048,576 words by 16 bits, fabricated with SAMSUNGs high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same device to be useful for a variety of high bandwidth, high performance memory system applications. 12.5.2.Features JEDEC standard 3.3V power supply LVTTL compatible with multiplexed address Four banks operation MRS cycle with address key programs -. CAS latency (2 & 3) -. Burst length (1, 2, 4, 8 & Full page) -. Burst type (Sequential & Interleave) All inputs are sampled at the positive going edge of the system clock Burst read single-bit write operation DQM for masking Auto & self refresh 64ms refresh period (4K cycle) 12.5.3.Pin Description
PIN CLK CS CKE NAME System clock Chip select Clock enable INPUT FUNCTION Active on the positive going edge to sample all inputs. Disables or enables device operation by masking or enabling all inputs except CLK, CKE and L(U)DQM Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one cycle prior to new command. Disable input buffers for power down in standby. Row/column addresses are multiplexed on the same pins. Row address : RA0 ~ RA11, Column address : CA0 ~ CA7 Selects bank to be activated during row address latch time. Selects bank for read/write during column address latch time. Latches row addresses on the positive going edge of the CLK with RAS low. Enables row access & precharge. Latches column addresses on the positive going edge of the CLK with CAS low. Enables column access. Enables write operation and row precharge. Latches data in starting from CAS, WE active. Makes data output Hi-Z, tSHZ after the clock and masks the output. Blocks data input when L(U)DQM active. Data inputs/outputs are multiplexed on the same pins. Power and ground for the input buffers and the core logic. Isolated power supply and ground for the output buffers to provide improved noise immunity. This pin is recommended to be left No Connection on the device.

Integrated SCART buffers The DOC system is designed to facilitate a very cost effective TV chassis. Some of the measures taken are: One crystal design. Only one reference crystal is required for the MPIF and ADOC, The advanced geometry corrections in the DOP result in a simple horizontal deflection circuitry. Linearity coils are not required 12.9.2.Features of the ADOC Processor Color Decoder and Sync Processing Multi standard color decoder supporting PAL-B, G, D, H, I, N, Combination-PAL N, PAL M, NTSC M, NTSC-Japan, NTSC 4.43 and SECAM Automatic color standard recognition and selection (PAL/SECAM/NTSC) Fully programmable static or Automatic Gain Control (AGC) for all analogue video base band signals. Resolution of CVBS or Y/C signal after AGC: 9 bits (including sync) AGC for chrominance (PAL and NTSC only) for CVBS and Y/C sources Programmable clamp window for selected video base band signal(s) Horizontal (including 3-level sync for 2Fh) and vertical sync detection. Adaptive 2/4-line delay Comb filter for two dimensional chrominance/luminance separation PAL delay line for correcting PAL phase errors Maskable interrupt generation to MIPS notifying any change of signal conditions Compliant with and detection of Macrovision up to version 7.1. Possibility of Fast Blank SCART RGB insertion in CVBS input mode, not in Y/C. Second multi standard color decoder for low-cost PIP Supports CVBS standards as listed above No comb filter No Y/C performance (Y and C are being summed before decoding) No fast blanking with Component inputs VBI Data Capture Two independent data capture units (DCU1 and DCU2) for standard data rate streams Multi-standard data capture. Both DCUs can always execute the following services: Line 21 Data Services (Closed Caption) European Wide Screen Signalling (WSS line23) PDC A & B (VPS and TeleText packet 8/30) World Standard TeleText. Services performed by TeleText application: Data Broadcast (packets X/30, X/31) Channel Identification (packet 8/30) Data type selectable on line-by-line basis independently for odd and even fields Multi-page acquisition during VBI Single page acquisition during full field DMA of packets and status bits to memory (embedded SRAM) Automatic identification of VBI data standard supported Teletext storage Error correction and decoding performed by DOCware software Page management performed by DOCware software Storage of up to 8 pages of TeleText internally Storage of more than 8 TeleText pages requires external memory (SDRAM) Picture measurements Noise measurement in active video Black Bar detection Sharpness measurement Picture Improvements Field based noise reduction (on main only) Horizontal Dynamic Peaking/ Luminance Transient Improvement (LTI) SCAn VElocity Modulation (SCAVEM or SVM) and Dynamic Contrast Control (DCC) Dynamic Color Transient Improvement (DCTI) Dynamic Skin Tone control 21 AK53 D.O.C. Service Manual 22/03/2004

33 AK53 D.O.C. Service Manual 22/03/2004
14.AK53 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS
All system, geometry and white balance alignments are performed in production service mode. Before starting the production mode alignments, make sure that all manual adjustments are done correctly. To start production mode alignments enter the MAIN MENU and then press the digits 4, 7, 2 and 5 respectively. The following first menu appears on the screen. The entire service menu parameters of AK53 CHASSIS are listed below. SERVICE MENU 1 VG2 STATUS 2 OPTIONS 3 GEOMETRY 4 VIDEO 5 SOUND 6 FACTORY You can go to the items in Service Menu by pressing /? buttons. Selected parameter will be ? highlighted. In order to enter the selected parameter except VG2 STATUS, press ? button. VG2 STATUS is entered by pressing OK button. In order to change the selected parameter, use ? /? buttons. To exit the service menu press M button. 14.1.OPTIONS Select Options in Service menu by pressing ? /? buttons and press button to enter Options ? menu. The following menu appears on the screen. OPTIONS 1 TILT OPTION 2 S-VHS 3 FRONT AV 4 EXT-BG 6 DK 7 L-LP 8I 9M 10 TXT LAST PAGE 11 CRT 12 AUTOSTORE 13 P. SMART OPTION 14 POWER ON
ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF ON/OFF 4:3/16:9 ON/OFF 1/2 DIRECT/ST-BY
TILT OPTION It is used for rotation adjustments of Real Flat (RF) tubes. If it is set to ON TILT option is seen in Picture menu. It is set to OFF for Super Flat (SF) tubes. S-VHS If S-VHS is set as ON this string is seen as AV source and also in user menu items. FRONT-AV If FRONT-AV is set as ON this string is seen as AV source and also in user menu items. EXT-3 If EXT-3 is set as ON this string is seen as AV source and also in user menu items. BG For standard BG, select ON other case select OFF.
34 AK53 D.O.C. Service Manual 22/03/2004
DK For standard DK, select ON other case select OFF. L-LP For standard L-LP, select ON other case select OFF. I For standard I, select ON other case select OFF. M For standard M, select ON other case select OFF. Set to OFF. TXT LAST PAGE Text last page can be changed to ON or OFF. If this parameter is selected as ON, while teletext page is exited and entered again in the same TV channel, last visited teletext page comes to the screen. Set to ON. CRT CRT option can be changed as 4:3 or 16:9 according to picture tube. AUTOSTORE Autostore option can be set to ON or OFF. If it is set to ON, Volume level and picture modes are stored automatically. Set to OFF for MEDION. P.SMART OPTION Picture Smart option can be set as 1 or 2. It will be set to 1 for MEDION. POWER ON It can be change between DIRECT or ST-BY. If DIRECT is selected TV starts directly whenever it switched off, if ST-BY is selected TV always waits in stand-by mode until RC or front panel keys are pressed. It will be set to ST-BY for MEDION.

35 AK53 D.O.C. Service Manual 22/03/2004
14.2.GEOMETRY Select Geometry in Service main menu by pressing /? buttons and press button to enter ? ? Geometry menu. The following menu appears on the screen. GEOMETRY 1 EW ALIGNMENT 2 V_SHIFT 3 SERVICE BLANK 4 VERT_AMP 5 UPPER LIN. 6 LOWER LIN. 7 VERT_S_CORR. 8 HOR SHIFT 9 HOR LINEARITY 10 HOR S CORR 11 HOR INNER PINC 12 HOR PAR 13 HOR BOW 14 TILT 15 PIP POSITIONS 28 4:3 SF ? 34 OFF ? 32 16:9 SF ? 41 OFF ?
. 14.2.1.EW ALIGNMENT Select Ew Alignment in Geometry menu by pressing ? /? buttons and press ? button to enter Ew Alignment menu. The following menu appears on the screen. EW ALIGNMENT 1 EW_WIDTH 2 EW PARABOLA 3 EW TRAPEZIUM 4 EW UPPER CORNER 5 EW LOWER CORNER 6 EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_EW_WAVE_4:3 SF 32 16:9 SF 82 100
To make East-West corrections first use; -EW_WIDTH -EW PARABOLA -EW TRAPEZIUM -EW UPPER CORNER -EW LOWER CORNER Then still needs to be a fine tuning use EW_WAVE_110. EW_WIDTH It can be adjusted between 0 254. 36 AK53 D.O.C. Service Manual 22/03/2004
EW PARABOLA It can be adjusted between 0 127. EW TRAPEZIUM It can be adjusted between 0 48. EW UPPER CORNER It can be adjusted between 0 48. EW LOWER CORNER It can be adjusted between 0 48. *Following 10 EW adjustment parameters make geometry corrections if fine tuning is necessary in geometry, each one of 10 parameter is responsible for each different dedicated area as seen below. EW_WAVE_1 EW_WAVE_2 EW_WAVE_3 EW_WAVE_4 EW_WAVE_5 EW_WAVE_6 EW_WAVE_7 EW_WAVE_8 EW_WAVE_9 EW_WAVE_10 EW_WAVE_1 It can be adjusted between 0 255. EW_WAVE_2 It can be adjusted between 0 255. EW_WAVE_3 It can be adjusted between 0 255. EW_WAVE_4 It can be adjusted between 0 255. EW_WAVE_5 It can be adjusted between 0 255. EW_WAVE_6 It can be adjusted between 0 255. EW_WAVE_7 It can be adjusted between 0 255. EW_WAVE_8 It can be adjusted between 0 255. EW_WAVE_9 It can be adjusted between 0 255. EW_WAVE_10 It can be adjusted between 0 255.
37 AK53 D.O.C. Service Manual 22/03/2004

42 AK53 D.O.C. Service Manual 22/03/2004
HOR INNER PINC Apply cross hatch pattern; try to improve bendings towards tube as straight by changing this parameter (Horizontal pincushion). It can be adjusted between 0 32. HOR PAR Change Horizontal Parabola by pressing ? /? buttons till vertical lines close to the both sides of the picture frame become parallel to vertical sides of picture tube without any bending to left or to right side of the screen. Check and readjust HOR PAR item if the adjustment becomes improper after some other geometric adjustments are done. It can be adjusted between 0 126. HOR BOW Change Horizontal Bow by pressing ? /? buttons till the vertical lines especially ones close to the left and right sides will of equal and symmetrical bending, i.e. they together will neither be towards left side nor right side. Check and readjust HOR BOW item if the adjustment becomes improper after some other geometric adjustments are done. It can be adjusted between 0 126. TILT Apply cross hatch pattern and look carefully top and button of the screen and try to make in parallel to tube with the lines by playing this parameter (This feature is given most of the time with real flat tubes) PIP POSITIONS PIP POSITIONS 1 PIP POS XPIP POS XPIP POS YPIP POS Y2

035 142

The values of X1, X2, Y1, Y2 coordinates the PIP position. X1 Y1 (X1, Y1) X2 (X2, Y1)

(X1, Y2)

(X2, Y2)
43 AK53 D.O.C. Service Manual 22/03/2004
14.3.VIDEO ALIGNMENTS Select Video in Service menu by pressing /? buttons and press ? button to enter Video menu. ? The following menu appears on the screen. VIDEO 1 MAIN AGC 2 PIP AGC 3 VIDEO ADJUST 4 COLOR ADJUSTMENT 5 IF_PLL_F_F 6 IF_PLL_OFF_NEG 7 IF_PLL_OFF_POS 8 OSD CONTRAST 9 TELETEXT CONTRAST 10 TXT HOR SHIFT 11 PAT HOR SHIFT 12 FLASH PROTECT 28 4:3 SF ? ? NORMAL OFF 32 16:9 SF ? ? NORMAL OFF
RED ONES ARE NOT RECOMMENDED TO CHANGE MAIN AGC: Is used to change the AGC voltage. Range 063 PIP AGC: nd Is used to change the AGC of 2 voltage. Range 063 14.3.1.VIDEO ADJUST Select Video adjust in Video menu by pressing /? buttons and press button to enter Video ? ? Adjust menu. The following menu appears on the screen. VIDEO ADJUST 1 WHITE DRIVE 2 MIN BRIGHTNESS 3 MIN CONTRAST 4 WHITE POINT R 5 WHITE POINT G 6 WHITE POINT B
44 AK53 D.O.C. Service Manual 22/03/2004
14.3.1.1.WHITE DRIVE Select White Drive in Video Adjust menu by pressing /? buttons and press button to enter ? ? White Drive menu. The following menu appears on the screen. WHITE DRIVE 1 NORMAL 2 WARM 3 COOL
14.3.1.1.1.NORMAL Select Normal in White Drive menu by pressing ? /? buttons and press ? button to enter Normal menu. The following menu appears on the screen. NORMAL 28 4:3 SF 32 16:9 SF 1 RED NORMAL 2 GREEN NORMAL 3 BLUE NORMAL 14.3.1.1.2.WARM Select Warm in White Drive menu by pressing ? /? buttons and press button to enter Warm ? menu. The following menu appears on the screen. WARM 1 RED WARM 2 GREEN WARM 3 BLUE WARM 28 4:3 SF 32 16:9 SF 150 155

WEST EURPOE X X X X X X X X
EAST EUROPE X X X X X X X
GREEKTURKEY X X X X X X X X X X

RUSSIAN

X X X X X X X X X X
49 AK53 D.O.C. Service Manual 22/03/2004

16.BLOCK DIAGRAM

50 AK53 DOC Service Manual 22/03/2004

17.CIRCUIT DIAGRAMS

11AK53-1 (SMALL SIGNAL)
51 AK53 DOC Service Manual 22/03/2004

11AK53-2 (SMPS)

52 AK53 DOC Service Manual 22/03/2004

11AK53-3 (DEFLECTION)

53 AK53 DOC Service Manual 22/03/2004
11AK53-4 (AUDIO POWER AMPLIFIER) 54 AK53 DOC Service Manual 22/03/2004
11FB53-1 (STEP-DOWN CONVERTER PLUS SUPPLY)
55 AK53 DOC Service Manual 22/03/2004
11FB53-2 (AUDIO/VIDEO SWITCHING + IF) 56 AK53 DOC Service Manual 22/03/2004
11FB53-3 (VIDEO/AUDIO/DEFLECTION/MICRO PROCESSING) 57 AK53 DOC Service Manual 22/03/2004

11TP53

58 AK53 DOC Service Manual 22/03/2004

NO 37 38

BILL OF MATERIAL LIST 10026509 COMPONENT CODE MATERIAL UNIT QTY V20048248 SNOW BOX ASSY.2980/81/85/86 PC 1,000 V20043519 SNOW BOX 2980-81 TOP PC 1,000 V60000011 EPS KG 0,584 V20043520 SNOW BOX 2980-81 BOTTOM PC 1,000 V60000011 EPS KG 0,584 V20085283 EXPEND KIT AK28 (2980/81) V.0 PC 1,000 V20004520 CABLE HOLDER DX15 (I) PC 1,000 V60000018 COPOLYMER POLYPROPYLENE KG 0,003 V20084045 STRAP TIE (L:118) PC 1,000 V60000018 COPOLYMER POLYPROPYLENE KG 0,001 V20085269 CABLE HOLDER CRT (I) UL94V-0 PC 1,000 V60000009 FR-HIPS NATR.V-0 SAFE KG 0,002 V70000331 ADHESIVE TAPE 75MM/660M (4125) M 2,246 V20097687 ON/OFF SW ASSY.FTZ(TOSHIBA)28"16:9-32-33 PC 1,000 V30002174 SWITCH SAFE ON/OFF 4A/64A PC 1,000 V30002368 CNAS 2P/650 AC MAINS W/C PC 1,000 V30016513 POWER CORD SAFE 2.2MT JVC (W/FILTER) PC 1,000 V40000127 SWITCH INSULATION DOOR LK101 PC 1,000 V40001898 MACARON (12cm.Is ile daralan) PC 1,000 V20108637 CN.ASY.52A-TRFPFC 1,7 A E54 + CONN 2/35 PC 1,000 V30018087 CNAS 2P/350 TRFPFC DIS W/C PC 1,000 V30018270 TRF PFC SAFE 1,7A 43MH 170W PC 1,000 V35000217 SCREW S C SYF YFMB 3.5*9.5 PC 2,000 V20110212 SPK.AS.2985/86 W/TWT (AK37) STR PC 1,000 V20110213 SPK.ASSY.2985/86 W/TWT (AK37)(R) PC 1,000 V20082948 BRACKET SPEAKER - 128X77 (2985/86) (I) PC 1,000 V60000008 HIPS (NATURAL) KG 0,041 V60000022 MASTERBATCH (BLACK) G 0,410 V30000426 CAP EL 6.8UF 50V M (BPL) PC 1,000 V30001947 TWEETER 8R 15W CLOSED PC 1,000 V30001950 SPEAKER 8R15W (77*128) PC 1,000 V30002238 CABL 2P/200 SPK DIS UL1672AWG24 PC 1,000 V30013905 CNAS 2P/900 DIS W/BLKC+FER UL2547 AWG24 PC 1,000 V35000224 SCREW C SK ZN YFMB 2.9*9.5 PC 6,000 V40009351 SPONGE -bracketspeaker 128X77 (55-Kg/m3) PC 1,000 V50011720 LABEL HIGH END PC 1,000 V20110214 SPK.ASSY.2985/86 W/TWT (AK37)(L) PC 1,000 V20082948 BRACKET SPEAKER - 128X77 (2985/86) (I) PC 1,000

PC PC PC PC PC PC PC PC PC PC PC PC PC G G G PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC
1,000 1,000 1,000 1,000 1,000 2,000 2,000 1,000 1,000 1,000 1,000 1,000 1,000 19,000 0,880 5,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 3,000 2,000 1,000 1,000 1,000 1,000
PL203 IC804 IC801 PL101 L805 PL423 IC401 Q100 TR801 PL422 PL853 PL108. Z900 X900 TU201. TU200 C861 PL804 R870 PL204 D811 TH801 RL801 IC105 PL107 F801. C141 R806 R952 R118 R829 R804 R186 R126
. PL424 IC402. R954 R832.

. R425.

482. 499 500. 513 514
V30000583 V30000590 V30000622 V30000628 V30000660 V30000712 V30000718. V30000729 V30000775 V30000779 V30000784 V30000815 V30000918 V30000925 V30000942 V30000983 V30001011 V30001036 V30001079 V30001159 V30001257 V30001284 V30001288 V30001291 V30001318. V30001323 V30001329 V30001344 V30001377 V30001979 V30001992 V30001996 V30006691 V30006712 V30009036 V30028752 V30000069 V30000074 V30000078
RES CF 1/4W 220R J RES CF 1/4W 2.2K J RES CF 1/4W 270R J RES CF 1/4W 2.7K J RES CF 1/4W 3.3K J RES CF 1/4W 470R J RES CF 1/4W 4.7K J. RES CF 1/4W 470K J RES CF 1/4W 6.8K J RES CF 1/4W 68K J RES CF 1/4W 680K J RES CF 1/4W 8.2K J RES MF 1/4W 2.1K F RES MF 1/4W 2.2K F RES MF 1/4W 27K J RES MF 1/4W 4.7K F RES MF 1/4W 6.8K F RES MF 1/4W 95K F RES MO 1W 100R J RES MO 1W 0.33R J RES MG SAFE 1/2W 4.7M J DIODE 1N4148 0.15A/100V 0.5A DIODE BYV27-200 2A/200V 50A DIODE HER107 1A/800V 30A DIODE BA159 1A/800V 20A. DIODE BY299 2A/800V 70A DIODE 1N4007 1A/1000V 30A DIODE ZENER 6.2V 1/2W DIODE ZENER 33V UZT 33B FIXED COIL 1UH Q45 M-A FIXED COIL 10UH Q65 K-A FIXED COIL 22UH Q40 K DIODE ZENER 3.3V FERRITE BEAD 3.5X4.7X0.8 RES FUSE SAFE 1/2W 0.1R J PCB 11AK53-1 CAP MKT 1NF 100V J CAP MKT 100NF 63V J CAP MKT 1UF 100V M
PC PC PC PC PC PC PC. PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC. PC PC PC PC PC PC PC PC PC PC PC PC PC PC
1,000 2,000 1,000 1,000 1,000 1,000 6,000. 1,000 1,000 2,000 1,000 1,000 2,000 1,000 1,000 1,000 2,000 1,000 1,000 1,000 1,000 1,000 1,000 3,000 7,000. 1,000 2,000 1,000 1,000 1,000 3,000 1,000 1,000 5,000 1,000 1,000 4,000 1,000 1,000

R105 R820 R165 R169 R866 R993 R110 R802 R129 R965 R157 R155 R434 R856 R855 R137 R805 R142 R156 R104 R810 R812 D404 D111 D106 D120 D818 D802 D812 D806 D113 L951 L803 L109 D813 L105 R125. C469 C142 C129
. R821. R127. R136. R121. R143. D107 D801 D123. D831. L1001. L106. C470.
. R823. D110 D814. L1000. L417. C472.
. R824. D815. L418. C473.

. R860. D829. J130.

523 524. 549 550. 553
V30000092 V30000099 V30000100 V30000104 V30000106 V30000107 V30000190 V30000271 V30000286 V30000295. V30000296 V30000298 V30000345 V30000346 V30000352 V30000353 V30000362 V30000367 V30000375 V30000387 V30000393 V30000400 V30000431 V30000433 V30000436 V30001384 V30001428 V30001454 V30001455 V30007308 V30007708 V30009208 V30019641 V30023137 V30000284 V30000294. V30000309 V30000469 V30000469
CAP MKT 220NF 63V J CAP MKT 33NF 63V J CAP MKT 330NF 63V J CAP MKT 4.7NF 100V J CAP MKT 47NF 100V J CAP MKT 47NF 250V J CAP CER 100PF 50V J CH CAP CER 680PF 50V J SL CAP CER 1NF 500V K B CAP CER 100NF 50V Z F. CAP CER 100NF 100V Z F CAP CER 1.5NF 50V K B CAP EL 10UF 50V M CAP EL 10UF 100V M CAP EL 100UF 16V M CAP EL 100UF 25V M CAP EL 1UF 50V M CAP EL 1UF 250V M CAP EL 220UF 16V M CAP EL 33UF 50V M CAP EL 3.3UF 50V M CAP EL 47UF 50V M CAP CER 100PF 1KV M CAP CER 1NF 1KV M B CAP CER 10NF 1KV ZE TR MCR22-6 TR BF423 TR BC548B TR BC558B CAP CER 220PF 1KV K (PULSE) CAP CER 1NF 1KV K (PULSE) CAP CER 470PF 1KV K (PULSE) CAP MKT 100NF 100V J NO-HIT IC TL431 %1 TOL (TO-92) CAP SMD 1NF 50V K R (0805) CAP SMD 100NF 50V K (0805). CAP SMD 2.2NF 50V K R 0805 RES SMD 1/10W 1K J 0805 RES SMD 1/10W 1K J 0805
PC PC PC PC PC PC PC PC PC PC. PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC. PC PC PC
1,000 1,000 4,000 1,000 2,000 1,000 1,000 1,000 1,000 6,000. 3,000 1,000 3,000 1,000 1,000 5,000 1,000 2,000 1,000 1,000 2,000 3,000 1,000 4,000 1,000 1,000 1,000 4,000 1,000 5,000 1,000 1,000 1,000 3,000 1,000 9,000. 1,000 1,000 2,000
C475 C812 C408 C144 C479 C149 C864 C130 C145 C831 C429 C146 C131 C104 C107 C468 C101 C106 C837 C857 C804 C845 C139 C116 C843 C868 Q817 Q806 Q105 Q814 C806 C154 C809 C135 Q116 C301 C100 C827 C811 R108 R834
. C428. C480. C430. C128. C953. C462. C862. C134 C828. C471. Q803. C813. Q815. C125 C846. R850
. C411. C824. C148. C954. C463. C956. C474. Q805. C814. Q816. C126 C817.
. C431. C410. C464. C860. Q810. C815. C803 C818.
. C409. C465. C155. C823.
566 567. 568. 569. 574 575. 582. 585 586. 587
V30000475 V30000503 V30000517 V30000529 V30000588 V30000593 V30000613 V30000626 V30000631 V30000636 V30000664 V30000710 V30000721 V30001285. V30001457. V30001458. V30001971 V30007026 V30007760 V30007763. V30009699 V30010560 V30012412 V30012510 V30012567 V30012568 V30012569. V30012574 V30012581 V30012585 V30012589. V30012590
RES SMD 1/10W 10K J 0805 RES SMD 1/10W 12K J (0805) RES SMD 1/10W 15R J 0805 RES SMD 1/10W 1.5K J RES SMD 1/10W 220R J 0805 RES SMD 1/10W 2.2K J (0805) RES SMD 1/8W 2.4K G RES SMD 1/10W 270R J RES SMD 1/10W 2.7K J 0805 RES SMD 1/10W 27K J 0805 RES SMD 1/10W 3.3K J (0805) RES SMD 1/10W 47R J (0805) RES SMD 1/10W 4.7K J DIODE 1N4148 SMD. TR BC848B SMD. TR BC858B SMD. FERRITE BEAT (805) BLM21A601S RES SMD 1/10W 5.1K J(0805) DIODE ZENER SMD BZT55C10 DIODE ZENER SMD BZT55C5V1. DIODE ZENER SMD BZT55C12 CAP SMD 220NF 25V K R (0805) DIODE ZENER 2.4V SMD RES SMD 1/16W 100R J (0603) CAP SMD 220PF 50V J (0603) CAP SMD 270PF 50V J (0603) CAP SMD 33PF 50V J (0603). CAP SMD 470PF 50V J (0603) CAP SMD 1NF 50V K R (0603) CAP SMD 2.2NF 50V K R (0603) CAP SMD 4.7NF 50V K (0603). CAP SMD 47NF 50V K (0603)

. R871 R516 R735 R730 R729. R793. R455 R461 R511. R703 R794 R844 R867 R515 R858. R885 R846 R879 R829 R835 R876. R869 R875. R113. R834. R738. R741 R792
. R884. R748 R737 R736. R795. R456 R499 R512. R711 R807 R852 R115 R513. R886. R882. R836 R825. R883. R114. R848. R752. R742 R800
. R739 R750. R803. R457 R500 R517. R713 R809 R101 R116 R826. R887. R448. R849. R782 R724
. R751. R104. R459 R820 R518. R714 R810 R762 R719 R841. R451. R783 R733
. 810. 814 815. 838. 843 844
. V30022089 V30022094 V30022098 V30022113 V30022118. V30022142 V30022201 V30022233 V30022242. V30022244 V30022250 V30022338 V30022477 V30022478 V30022479 V30022481 V30022895 V30022896 V30022958 V30023096 V30025524 V30029152 V20127632 V20127634 V20127639 V30010571 V30001457 V30001458 V30012582 V30012657. V30012692 V30012696 V30016162 V30016654 V30020936 V30021960
. RES SMD 1/16W 680R J (0402) RES SMD 1/16W 680K J (0402) RES SMD 1/16W 390R J (0402) RES SMD 1/16W 68R J (0402) RES SMD 1/16W 75R J (0402). RES SMD 1/16W 2.7K F (0402) CAP SMD 1.2NF 50V J (402) CAP SMD 12PF 50V J (402) CAP SMD 68PF 50V J (402). CAP SMD 100PF 50V J (402) CAP SMD 330PF 50V K (402) CAP SMD 4.7NF 50V J (402) IC STEP DOWN CS51033 1A SO8 DIODE SCH BAT254 0.2A/30V SOD110 IC LDO LM1086 3.3V/1.5A D2PAK VINMAX=18V RES SMD 1/16W 240R F (0402) IC RESET NE56610-29 RES SMD 1/16W 1.2K F (0402) TR PMOS STS5PF30L -5A/-30V SO8 FIXED COIL SMD 10uH 2.5A 10x10x4.5mm TR PMEM4010PD PNP/SCH -1A -40V SOT457 C SDRAM 64MBIT(1Mx16bitx4bank)TSOP(CTV) MD.SMD.FB53-FAV IN (ST) MD.SMD.FB53-FRONT SVHS (ST) MD.SMD.FB53-SCART3 (ST) CAP EL 10UF 16V M TR BC848B SMD TR BC858B SMD CAP SMD 10NF 50V K R (0603) RES SMD 1/16W 1K J (0603). RES SMD 1/16W 4.7K J (0603) RES SMD 1/16W 47K J (0603) FERRITE BEAD (0805) BLM21A102FPT CAP SMD 100NF 16V K R (0603) COIL SMD 10UH 300mA WINDING TYPE(1210) RES SMD 1/16W 47R J (0402)
. PC PC PC PC PC. PC PC PC PC. PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC. PC PC PC PC PC PC
. 3,000 1,000 1,000 3,000 12,000. 1,000 2,000 1,000 7,000. 5,000 3,000 2,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 2,000 5,000 1,000 1,000 6,000. 4,000 4,000 3,000 4,000 2,000 1,000
R746 R726 R873 R428 R797 R412 R468 R712 R110 C542 C806 C127 C705 C125 C840 C420 IC104 D713 IC103 R761 IC316 R111 IC105 L101 Q106 IC315. C497 Q408 Q407 C441 R406 R487 R462 R438 L425 C445 L459 R520
R755 R734. R449 R420 R470 R424. C543. C520 C782 C428 C841 C773. C517 Q409. R407. R463 R439 L427 C539 L460.
R764 R747. R450 R423 R471. C521. C792 C842. Q410. R466. R480 R473 L463 C540.

. R465 R472. C522. C836. Q411. R469. R481 R492. C811.
. R467 R710. C702. C835. Q414. R482.
V30021996 V30022030 V30022042 V30022113 V30022118 V20127654 V30012582 V30021991 V30022118 V20127655 V30000413 V30012641 V30012692 V20127660 V30022085 V20127665 V30000352 V30000371 V20127671 V30001457 V30012411 V30016126 V30016654 V30018093 V30022046 V30022069 V30022084 V30022338 V20127701 V20127714 V20127717 V20127721 V30021602 V20127773 V20133674 V30001285 V30001457 V30007169 V30012504 V30012509 V30012510
RES SMD 1/16W 10K J (0402) RES SMD 1/16W 15K J (0402) RES SMD 1/16W 1K J (0402) RES SMD 1/16W 68R J (0402) RES SMD 1/16W 75R J (0402) MD.SMD.FB53-W/PIP (ST) CAP SMD 10NF 50V K R (0603) RES SMD 1/16W 100R J (0402) RES SMD 1/16W 75R J (0402) MD.SMD.FB53-W/ROTATION (ST) CAP EL 4.7UF 50V M RES SMD 1/16W 10K J (0603) RES SMD 1/16W 4.7K J (0603) MD.SMD.FB53-W/BSVM (ST) RES SMD 1/16W 33R J (0402) MD.SMD.FB53-HEADPHONE (ST) CAP EL 100UF 16V M CAP EL 22UF 50V M MD.SMD.FB53-PSBGDK L/L' (ST) TR BC848B SMD DIODE BA782 SMD CAP SMD 220NF 16V K R (0603) CAP SMD 100NF 16V K R (0603) COIL SMD 3.3uH (2520) RES SMD 1/16W 2.2K J (0402) RES SMD 1/16W 6.8K J (0402) RES SMD 1/16W 33K J (0402) CAP SMD 4.7NF 50V J (402) MD.SMD.FB53-WO/TIMESHIFT (ST) MD.SMD.FB53-WO/HDTV (ST) MD.SMD.FB53-WO/IDTV (ST) MD.SMD.FB53-HIGHENDS2 (ST) IC PNX3006E / N302 MD.SMD.FB53-WO/DVD (ST) MD.SMD.FB53-COMMON (ALT) DIODE 1N4148 SMD TR BC848B SMD DIODE BAV99 (SOT23) 0.25A/70V 4.5A RES SMD 1/16W 1.2K J (0603) RES SMD 1/16W 100K J (0603) RES SMD 1/16W 100R J (0603)
1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 2,000 4,000 1,000 1,000 1,000 1,000 1,000 1,000 2,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 4,000
R519 R847 R454 R453 R416. C429 R431 R419. C790 R784 R779. R898. C713 C700. Q404 D400 C535 C436 L457 R433 R432 R430 C432. IC313. D701 Q403 D715 R435 R791 R402

. C714 C701. R437. R403

. C706. R478

. C707. R479

892. 895. 896 897. 898. 899. 902 903. 904 906. 907 908. 909.
V30012560. V30012566 V30012574 V30012581. V30012610 V30012641. V30012657. V30012662. V30012669 V30012692 V30012692 V30012696. V30012714 V30016126. V30016162 V30016654. V30020531.
CAP SMD 100PF 50V J (0603). CAP SMD 22PF 50V J (0603) CAP SMD 470PF 50V J (0603) CAP SMD 1NF 50V K R (0603). CAP SMD 10NF 50V J (0603) RES SMD 1/16W 10K J (0603). RES SMD 1/16W 1K J (0603). RES SMD 1/16W 2.7K J (0603). RES SMD 1/16W 22K J (0603) RES SMD 1/16W 4.7K J (0603) RES SMD 1/16W 4.7K J (0603) RES SMD 1/16W 47K J (0603). RES SMD 1/16W 820R J (0603) CAP SMD 220NF 16V K R (0603). FERRITE BEAD (0805) BLM21A102FPT CAP SMD 100NF 16V K R (0603). FERRITE SMD (805) BLM21PG221SN1.