Thank you for choosing Meliconi.
This universal remote control is used for all the main functions of 4 remote controls (TV - VCR - SAT - DVD) of the brands listed at the back of the pack. Keep your Instructions Booklet and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
VCR selection key for using the VCR. This key lights up whenever you use a VCR command. SAT selection key for using the satellite receiver. This key lights up whenever you use a receiver command. DVD selection key for a DVD unit or another unit (Decoder, Pay-TV, Video projector, Monitor, etc.). This key lights up whenever you use a DVD command. ON/OFF key for TV - VCR - SAT and DVD.
Used to access additional commands and to program the remote control.
TV selection key for using the TV. This key lights up whenever you use a TV command. Teletext keys: to access Teletext to close Teletext and return to normal viewing Teletext page hold function additional Teletext function. Confirm key. To select the next (P+) or previous (P-) channel or program. These keys can also be used to move up and down in the MENU. Mute key.
Number keys. To access your MENU. Move within the MENU using the +/- and P +/keys or SHIFT with +/- P +/- depending on the model of your original remote control. Control the volume using +/-. These keys can also be used to move to the right and left in the MENU. To select an external terminal. User customisation keys for memorising and accessing additional commands.
TV Fastext Func. Red Green

VCR Record Rewind Stop

TV Fastext Func. White/Violet Blue Yellow
VCR Additional Func. Fast forward Pause Play
The functions described above are only operative if your appliance also has them.

FITTING THE BATTERIES

Before programming and using the remote control, fit the batteries. The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown. The batteries must be changed once a year. If the TV - VCR - SAT - DVD selection keys start to flash during use, this indicates that the batteries are low and should be changed. When you remove the batteries, fit the new ones within 5 minutes or you may have to reprogram your remote control. Make a note of the codes for the TV - VCR - SAT DVD equipment on the adhesive label inside the battery cover. This note will be handy if you have to reprogram your control.

SET-UP

Read these instructions carefully before programming your remote control! To program the CONTROL 4 Plus remote control, follow the indications in section A , B or C.
BRAND SEARCH PROGRAMMING MODE
Warning: program one appliance at a time.
1. Turn ON the appliance: if a VCR, insert a cassette if SAT, select a program if DVD, insert a DVD. 2. In the code book enclosed, look for the brand of your appliance and make a note of the code indicated at the side (e.g. Philips 001) or the code for the brand indicated by the arrow.

TV 3. SAT VCR DVD

7. When the appliance responds correctly, press SHIFT to confirm. Three flashes indicate that the operation has been completed correctly. Additional check Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 3. Identify and make a note of the code for the appliance which you have searched for, following the code noting procedure (see NOTING THE PROGRAMMED CODE section). NOTE: THE SELECTION KEY STOPS FLASHING. The remote control leaves the programming mode and the TV - VCR - SAT - DVD selection key stops flashing: if no keys are pressed for 15 seconds if an invalid brand code is entered if the code search list is completed. In this case, go back to point 3 or switch to programming mode C if you press the TV - VCR - SAT - DVD F1 - F2 - F3 - F4 keys by mistake.
Press and release the TV - VCR - SAT DVD selection key for the appliance you want to use: the TV key is used to search only for the TVs of the brand selected the VCR key is used only for the VCRs the SAT key is used only for the SATs the DVD key is used only for the DVDs.

4. Hold down the SHIFT and ON/OFF keys together until the TV - VCR - SAT - DVD selection key starts to flash indicating that the remote control is in programming mode.
5. Release the keys. Within 15 seconds, enter the brand code previously identified (e.g. 001). The TV- VCR - SAT -DVD selection key flashes more quickly to indicate that the remote control is ready for the search. 6. Point the remote control at the appliance. Press and release slowly one of the most frequently used keys several times STOPPING when the appliance responds correctly to the command.
1. Turn ON the appliance: if a VCR, insert a cassette if SAT, select a program if DVD, insert a DVD.

DIRECT CODE ENTRY

Warning: program one appliance at a time. Additional check Point the remote control at the appliance. Check that the appliance responds correctly to the commands sent. If there is no response or the appliance only responds partially or incorrectly, it is probable that you have used the wrong code. In this case, try the procedure again from point 3. This time, however, use the NEXT CODE in the list (e.g. 111 for TV - 348 for VCR, etc.).
2. In the code book enclosed, look for the brand of the TV-VCR-SAT-DVD appliance you want to control and make a note of the first code in the list BENEATH the brand previously identified (e.g. Philips TV 103 - VCR 345, etc.).
Press and release the TV - VCR SAT - DVD selection key for the appliance you want to use. You cannot set a VCR code using the TV key.
Note down the TV - VCR - SAT - DVD codes used to program the remote control on the adhesive label inside the battery cover for rapid consultation.
4. Hold down the SHIFT and ON/OFF keys together until the TV - VCR SAT - DVD selection key starts to flash indicating that the remote control is in programming mode.
5. Release the keys. Within 15 seconds, enter the code previously identified (e.g. TV 103). Three flashes indicate that the code has been saved correctly. If not, try the code entry procedure again from point 3.
NOTE: THE SELECTION KEY STOPS FLASHING. The remote control leaves the programming mode and the TV - VCR SAT - DVD selection key stops flashing if no keys are pressed for 15 seconds if an invalid code is entered if you press the TV - VCR - SAT - DVD F1 - F2 - F3 - F4 keys by mistake.
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
This operation may take up to about 20 minutes. Warning: program one appliance at a time.

1. Turn ON the appliance: if a VCR, insert a cassette if SAT, select a program if DVD, insert a DVD. 2. TV SAT VCR DVD Press and release the TV - VCR - SAT DVD selection key for the appliance you want to use: the TV key is used to search only for the TVs of the brand selected the VCR key is used only for the VCRs the SAT key is used only for the SATs the DVD key is used only for the DVDs.
6. When the appliance responds correctly, press SHIFT to confirm. Three flashes indicate that the operation has been completed correctly. Additional check Check that some of the other functions used on your original remote control are working correctly. If the commands function incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 2. Identify and make a note of the code for the appliance which you have searched for, following the code noting procedure (see NOTING THE PROGRAMMED CODE section). NOTE : THE SELECTION KEY STOPS FLASHING. The remote control leaves the programming mode and the TV - VCR SAT - DVD selection key stops flashing: if no keys are pressed for 15 seconds if the code search list is completed if you press the TV - VCR - SAT - DVDF1 - F2 - F3 - F4 keys by mistake.
3. Hold down the SHIFT and ON/OFF keys together until the TV - VCR SAT - DVD selection key starts to flash indicating that the remote control is in programming mode.
4. Release the keys. Within 15 seconds, enter the code 000. The TV- VCR - SAT -DVD selection key flashes more quickly to indicate that the remote control is ready for the search. 5. Point the remote control at the appliance. Press and release slowly one of the most frequently used keys several times STOPPING when the appliance responds correctly to the command.
NOTING THE PROGRAMMED CODE
Always write down the 3-digit code for your remote control on the label inside the battery cover after running the search and saving the code. This may be useful if you need to reprogram your remote control in the event of accidental cancellation or when you change used batteries. If you forget to write down the code or use the remote control programming procedures A or C. dont worry!

To find the code for your remote control:

TV 1. SAT VCR DVD

Press one of the TV - VCR - SAT - DVD selection keys for the appliance whose code you want to identify.
2. Hold down the SHIFT and ON/OFF keys together until the TV - VCR SAT - DVD selection key starts to flash.
communicates the code by flashing the three numbers separately. Count the number of flashes for each code number. For example, for the code 306, the button flashes three, zero and six times to give: =3 =0 =6 5. Note this code on the label inside the battery cover for rapid consultation.
3. Release the SHIFT and ON/OFF keys and then press and release the 1-/-key. 4. After a few seconds, the TV - VCR SAT - DVD selection key you used
USING THE REMOTE CONTROL WITH MORE THAN ONE APPLIANCE OF THE SAME TYPE
You can also use the TV - VCR - SAT - DVD selection keys for different appliances. See the table below.

BUTTONS

APPLIANCES VCR SAT

TV VCR SAT DVD

1. One at a time, search for the codes for each appliance, following any of the programming procedures A , B or C described above. 2. Make a note of the various appliance codes. 3. Enter the codes following the programming procedure B from point 3 and assign the appliances to the selection keys as you like.
In this way, you can obtain all the combinations required. Simply program the remote control as follows:
VOLUME CONTROL AVAILABLE AT ALL TIMES
If you have programmed the CONTROL 4 Plus remote control for the TV using the TV selection key and for the VCR using the VCR selection key, you can raise or lower the TV volume or use the mute function while watching the VCR without having to press the TV selection key.
USING THE ADDITIONAL COMMANDS WHICH DO NOT APPEAR ON THE KEYPAD
Although not indicated on the keypad, some keys can be used for additional commands. 1. Use your CONTROL 4 Plus remote control to find them by pressing the following keys one by one:

1-/-2MENU OK AV

2. The most frequently used additional commands like MENU SCROLL COLOUR BRIGHTNESS and NORMALISATION are located as follows: normalisation menu (up) menu (down) menu (right) menu (left)

+ P P -

menu (up) menu (down) menu (right) menu (left)

+ + + +

brightness (-) brightness (+) color (-)

red green yellow blue

brightness (-) brightness (+) color (-) color (+)

color (+)

3. FOR THE LESSER-USED FUNCTIONS, refer to the code book appendix. Find the symbol table corresponding to the code you saved to program the remote control. Locate the additional function you require and note down the symbol or number which appears below it. EXAMPLE: XXX CODE TABLE Original remote control additional functions
REV RIV TUPO TIME CANCEL ORA +
CONTROL symbols or numbers
+ TP OFF MEM F TP ON MEM FULL TOT EXP TOP EXP BOT ALTO I-II

MENU MENU

014 015
There are 4 ways to enable the additional commands: A - TV function example: brightness (+) C - TV function example: EXP BOT
A symbol appears beneath the function. Locate this symbol on your remote control and press the key to transmit the function to the appliance. The command stops when you release the key. B - TV function example: FULL TOT
A number appears beneath the function (028). Press and hold down SHIFT. Type in the number, holding down the last digit (8). The function is transmitted to the appliance and stops when you release the two keys (SHIFT+ 8). D - TV function example: contrast +
A symbol against a grey background appears beneath the function. Locate this symbol on your remote control. Press SHIFT and the key at the same time. The corresponding function is transmitted to the appliance and stops when you release the keys.
A symbol and a number are displayed beneath the function. You can apply the command using either the symbol or the number. Locate this symbol on your remote control and press the key to transmit the function to the appliance. If you want to use the number, refer to example C above.
NOTE : You cannot use the additional commands unless these were already available on your original remote control.

PROGRAMMABLE KEYS

You can customise your remote control to use any 4 additional TV-VCR-SATDVD functions, using the function keys F1- F2 - F3 - F4. In the symbol table corresponding to your remote control code, locate the additional function you require and note down the number which appears below it. Note that only number functions can be saved using F1- F2 - F3 - F4. The function programming procedure is as follows: TV function example: EXP BOT Press and hold down SHIFT and type in the number written beneath function 028. Press one of the function keys (e.g. F1) and hold it down together with SHIFT. After a few seconds, the TV-VCR-SAT-DVD selection key for the appliance you have chosen will emit a series of 3 flashes to indicate that the function has been saved correctly. Release SHIFT and F1. From now on, whenever you press F1, the additional command just saved is transmitted to the appliance and stops when F1 is released.
NOTE : If the TV - VCR - SAT - DVD selection key does not flash, repeat the saving procedure described above.

TROUBLESHOOTING

PROBLEM The appliance does not respond and the TV - VCR - SAT - DVD selection keys do not light up when you press a key. SOLUTION Try some of the other frequently used keys. If the problem persists, check that the batteries are fitted correctly. If necessary, replace them with 2 new 1.5 V AAA/LR03 alkaline batteries. Check that the batteries are new and that the remote control is pointing at the appliance without any obstacles in the way. If required, reset the remote control code, following the programming procedure A or B or C. The batteries are low. Change them. You may have used the wrong code. Reset the remote control code, following the programming procedure A or B or C. Set the remote control code, following the global search programming procedure C.

The appliance does not respond but the TV - VCR - SAT - DVD selection keys light up.
The TV - VCR - SAT - DVD selection keys are flashing. The remote control commands are not all working correctly.
The brand for your appliance is not listed in the Code Book.

INFO-LINE

If you have any queries about CONTROL 4 Plus: read this booklet carefully; this will help you to solve almost all problems consult our Internet site www.meliconi.it to answer all your queries more easily and quickly.
WARRANTY: 2 years Agents stamp Tampering or improper product use will void this guarantee. Remote control model CONTROL 4 Plus

Purchase date