Thank you for choosing a Meliconi remote control.
Keep this booklet for future reference.
The FULLY 8 RC universal remote control is ideal for replacing up to 8 remote controls of any brand for TV, Digital Terrestrial (TER), Satellite (SAT) Decoders, DVD players (including Blu Ray), Videotape recorders (VCR), Personal video recorders (PVR), cable TV (CAB), other audio video equipment (AUX) or decoders for ADSL TV (ADSL). The remote control has a nonvolatile memory, meaning that it does not lose its settings even if there are no batteries in it. IMPORTANT: the device must not be exposed to excessive heat sources.

Fully 8 RC

USE OF THE BUTTONS AND FUNCTIONS
The functions of the buttons described below are available only if they are also present on the original remote control. Buttons for selecting the device to be controlled.
Displays the list of programmes For selecting an external input source
Numeric keypad Selects digital TV and radio Volume control +/

Selects analogue/digital

For selecting the next programme P+ or the previous programme P MUTE turns sound OFF and ON
For moving around within the MENU Specic buttons for decoder TELETEXT buttons
Conrm selection Fastext functions or for selecting sub-menus using colours DVD/PVR RECORD PAUSE STOP PLAY buttons DVD and PVR forward/back functions
ON/OFF switches the device OFF and in some cases ON

INSERTING THE BATTERIES

The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries. Insert them as illustrated. Try pressing a number button and check that the red light remains lit continuously until you release the button: if the light ashes, the batteries inserted are not charged and are about to go at, therefore you must substitute them. Do not leave at batteries inserted, as liquid may leak and damage the remote control

SETTING CODES

The Fully 8 RC remote control is a universal remote, so its memory contains data relating to numerous devices of various brands available on the market. Each original device has a specic code which must be used to set up the remote control. Therefore, to use your Fully 8 RC you must enter the specic code for each device you wish to control. So use one of the following methods to identify the correct code and set it in your remote control: A) - INTERNET (recommended) B) - CELL PHONE (SMS) C) - MANUAL SEARCH
SETTING CODES USING INTERNET
If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guida website to identify the specic codes for the devices you wish to command. Then set the codes manually in your MELICONI remote control as described in the ENTERING THE CODE DIRECTLY procedure.
SETTING CODES USING A CELL PHONE
Today, Meliconi gives customers who dont have internet the chance to receive the codes for programming their remote control directly on their cell phone. Simply send an SMS to this number 7518893 as follows: 8A, Type, Brand, Model - Type = indicate the device to be controlled using one of the following abbreviations: TV - SAT - DVD - VCR - TER (Digital Terrestrial decoder) - AUX (other audio video device). - Brand, Model = to indicate the brand and the model of the device to be controlled. Example: 8A, TV, PHILIPS, 32PFL3614 (if you dont know the model, dont write anything after the brand). Once you have received the SMS with the list of codes, set the rst code in the remote control as described in the ENTERING THE CODE DIRECTLY section. Stand in front of the device with the MELICONI remote control. Turn the device on and then press the OFF button on the remote (or the PLAY button if the device is a VCR/DVD). If the device does NOT switch off (or if the VCR/DVD does not start playing), try setting the consecutive code in the SMS list in the remote control. When the device reacts check whether the other buttons are operating correctly too. If they do, the remote control is ready to use. If they dont, you are probably using an incorrect code destined for a very similar device; at this point ignore the SMS list and consult the SETTING CODES USING A MANUAL CODE section to nd a more suitable code. NOTE: If you dont receive an SMS on your cell phone or if the message says ERROR / NO CODE, it means the system has not been able to process the data you have sent; Do not try sending another SMS use the MANUAL SEARCH instead.

SETTING CODES USING A MANUAL SEARCH
(only to be performed if the specic code could not be found) 1. Switch on the device to be programmed: if TV, SAT, TER select a programme - if DVD insert a DVD, for videotape recorders insert a cassette 2. Hold down the selection button corresponding to the device whose code you want to nd (e.g.: light starts to ash. 3. Now release the button and briey press the button or for a DVD, VCR and PVR. 4. The indicator light ashes faster; the remote control is ready for the search. or button several times, stopping when the 5. Point the remote control at the device. Slowly press and release the device responds correctly to the command sent (you may need to press the button several dozen times). 6. When the device responds correctly, press the correctly. button. Three long ashes indicate that the operation was completed ) until the indicator
Check that the other buttons correspond to the functions of the original remote control; if not, it is likely that the code found is incorrect, but is used for a very similar device. In that case, repeat the procedure from point 2. If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN USE procedure and make a note of it inside the battery cover. NOTE: During the search the indicator stops ashing and the remote control exits the programming mode in the following cases: if for 12 seconds the button indicated is not pressed or if another button is pressed if the list of codes to nd is terminated. If this happens, go to the www.meliconi.com website
ENTERING THE CODE DIRECTLY
(only to be performed if you know the specic code to be set) 1. Hold down the selection button corresponding to the device whose code you want to enter (e.g.: light starts to ash. ) until the indicator
2. When the indicator light starts ashing, release the button and immediately enter the specic code previously found (e.g.: 1306). Three long ashes indicate a correct setting. If they do not appear, repeat the procedure.

DISPLAY CODE IN USE

If you set up the remote control using the MANUAL SEARCH procedure, obtain and make a note of the code in use as follows: 1. Hold down the selection button corresponding to the device whose code you want to nd (e.g.: light starts to ash. 2. When the indicator light starts ashing, release the button and briey press the button. ) until the indicator
3. After a pause of several seconds, the indicator light produces four sets of ashes, spaced out, corresponding to the code to be obtained. Count the number of ashes. Each set of ashes corresponds to one gure in the code. Ten ashes correspond to the gure 0.

Code obtained = 1306

4. Make a note of the code obtained on the label on the inside of the battery cover. You may need it in future.

TROUBLESHOOTING

PROBLEM The device does not respond and the indicator light does not come on when a button is pressed. The device does not respond but the indicator light comes on. SOLUTION Make sure that the batteries are inserted correctly, or substitute them with 2 new 1.5V alkaline AAA/LR03 batteries. Make sure that the batteries are new and that the remote control is pointing at the device without any obstacles between them. If necessary, enter the remote control code again by repeating the programming procedure. Substitute the batteries, which are about to go at. You may be using an incorrect code. Enter the remote control settings again by repeating the programming procedure.
When you press a button the indicator light ashes and the device does not respond to commands. The remote control does not execute all commands correctly.

INFO-LINE

carefully read this Instructions Booklet which will allow you to solve most problems. consult our website www.meliconi.com where you will nd the answers you need in the fastest, easiest way.

2 year WARRANTY

The warranty is voided if the product is tampered with or used improperly. Retailer stamp
If you have any questions about the new Fully 8 RC remote control:
Remote control model: Fully 8 RC

Purchase date

The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the product must be collected separately from other waste. Therefore, at the end of the devices life, you must take it to appropriate centres for the differentiated collection of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent type, on a one-for-one basis. Suitable differentiated collection to allow subsequent recycling of the decommissioned device, with environmentally-compatible treatment and disposal, help to prevent any negative effects on the environment and health and to promote the recycling of the materials of which the device is made.