Thank you for choosing Meliconi.
This simplified universal remote control contains all the main functions of most TV remote controls of the brands listed on the back. Keep your Instructions and Code Booklet for future reference.
USING THE KEYS AND FUNCTIONS
To select the next programme or to turn ON your TV.
ON/OFF to turn OFF your TV and, in some cases, to turn ON your TV.
Press them together to turn ON your TV on programme 1.
Control the volume using +/-.
To select an external terminal.
Mute key. To select the previous programme or to turn ON your TV.

FITTING THE BATTERIES

Before programming and using the remote control, insert batteries. The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown: Batteries must be changed once a year. Change the batteries if the light indicator starts to flash during use. The batteries are low. When removing batteries, insert the new ones within 5 minutes or you may have to reprogram your remote control. Make a note of the code for your TV on the adhesive label supplied inside the battery compartment cover. This note will be handy if you have to reprogram your remote control.

SET-UP

Read these instructions carefully before programming your remote control! Once you have programmed Speedy, you can turn ON your TV in three ways: Press P or P. + Press P and P simultaneously: this sends the code for programme 1. Press.
is indicated, you must press P or +
+ When + is indicated, you must press P or +
To return to programme 1 directly, press P and P simultaneously.
To program Meliconi Speedy remote control, follow the indications in paragraph A or B.
BRAND SEARCH PROGRAMMING MODE
7.IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR ORIGINAL REMOTE CONTROL If your remote control does not have the programme + selection keys (e.g. P / P , +/-, CH+/-.etc) once you have programmed Speedy, you can still select the programmes from 0 to 9, as follows: Hold down the AV and keys simultaneously until the light indicator starts to flash indicating that the remote control is in programming mode. Release the keys and + press P 8 times within 12 seconds. Three flashes indicate that the operation has been completed correctly. Make sure you can change programmes from 0 to 9 + using the P and P keys. If not, repeat the search operation, starting from point 3.
1.Find the code for your TV in the code list (see middle of this booklet). Make a note of the code found. It has 4 + and - signs, indicated to the side (e.g. Thomson - + - +). 2. Make sure that the TV is ON. 3.Hold down the AV and keys simultaneously until the light indicator at the top starts to flash indicating that the remote control is in programming mode. 4.Release the keys. Within 12 seconds, enter the brand code previously identified (e.g. - + - +). 5.Point the remote control at the TV. Press and release the key slowly several times. STOP when your TV goes OFF. 6.When your TV is OFF, press the AV and keys simultaneously. When you release the keys, three flashes indicate that the search operation has been completed correctly.
Additional check Check that all 7 keys are operating correctly. If the commands work incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 3 until all keys respond correctly to the commands sent. If you cannot find the right code after several attempts, switch to programming mode B.

Identify and take note of the TV code which you have searched for, following the code noting procedure (see "PROGRAMMED CODE NOTING" section).
NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY. THE LIGHT INDICATOR STOPS FLASHING. The remote control leaves the programming mode and the light indicator stops flashing: if no keys are pressed for 12 seconds if an invalid brand code is entered if you press keys other than those indicated if the code search list is completed. In this case, switch to programming mode B.
GLOBAL SEARCH REMOTE CONTROL PROGRAMMING
This operation may take a few minutes.
+ 1. Make sure that the TV is (e.g. P / P , +/-, CH+/ON.etc), once you have 2.Hold down the AV and programmed Speedy, keys simultaneously until you can still select the the light indicator at the top programmes from 0 to 9, starts to flash indicating as follows: that the remote control is Hold down the AV and in programming mode. keys simultaneously until 3.Release the keys, point the the light indicator at the top remote control at your TV starts to flash indicating and press and release the that the remote control is key, slowly several in programming mode. times. STOP when your TV Release the keys and + goes OFF. press P 8 times within 4.When your TV is OFF, 12 seconds. press the AV and keys Three flashes indicate that simultaneously. When you the operation has been release the keys, three completed correctly. flashes indicate that the Make sure you can change search operation has been programmes from 0 to 9 + completed correctly. using the P and P keys. 5.IF YOU DO NOT HAVE THE If not, repeat the search PROGRAMME SELECTION operation, starting from KEYS ON YOUR ORIGINAL point 2. REMOTE CONTROL If your original remote control does not have the programme selection keys
Additional check Check that all 7 keys are operating correctly. If the commands work incorrectly or erratically, you have probably entered a code for a similar but different remote control. In this case, repeat the search procedure from point 2 until all the keys respond correctly to the commands sent.
NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY. THE LIGHT INDICATOR STOPS FLASHING The remote control leaves the programming mode and the light indicator stops flashing: if no keys are pressed for 12 seconds if you press keys other than those indicated if the code search list is completed. In this case, visit www.meliconi.it or contact the call center.

PROGRAMMED CODE NOTING

When you have programmed Speedy Meliconi, note down the code on the label in the battery compartment cover. To find the code for your remote control: 1. Hold down the AV and keys simultaneously until the light indicator at the top starts to flash indicating that the remote control is searching for the code. + 2. Release the keys and, within 12 seconds, press P and

simultaneously.

3. Release P and P and pay attention to the flashing of the LEDs: a long flash corresponds to a + while a short flash corresponds to a -. Note the sequence of the 8 flashes and note them down on the label in the battery compartment cover, from left to right.
RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN
If the remote control is no longer programmed because it has been left without batteries for a long time or has flat batteries, you can re-program it quickly as follows: 1. Hold down the AV and keys simultaneously until the light indicator at the top starts to flash indicating that the remote control is programming. 2. Release the keys and, within 12 seconds, using the + P and P keys, enter the eight-sign code which you noted down before. At the end, three flashes indicate that the code has been saved correctly. If not, try the code entry procedure again from point 1.

TROUBLESHOOTING

PROBLEM The TV does not respond and the light indicator does not light up when you press a key. The TV or VCR does not respond but the light indicator does light up. SOLUTION Check that the batteries are fitted correctly. If necessary, replace them with 2 new 1.5 V AAA/LR03 alkaline batteries. Check that the batteries are new and that the remote control is pointing at the appliance without any obstacles in the way. If required, reset the remote control code, following the programming procedure A or B. Batteries are low. Replace them.
The TV does not respond and the light indicator flashes. Not all remote control commands are working correcting.
You may have used the wrong code. Reset the remote control code, following the programming procedure A or B.
The code for your TV brand Set the remote control code, following the global search is not in the Code list. programming procedure B.
+ The P and P keys do not select the programmes.
The original remote control may not have had this function. In + this case, set the code (press P 8 times) as described in paragraphs A or B.

INFO-LINE

If you have any queries about Speedy: read this booklet carefully this will help you to solve almost all problems consult our Internet site www.meliconi.it to answer all your queries more easily and quickly.

WARRANTY: 2 years The warranty ceases to be valid if the product is tampered with or used incorrectly. Remote control model Purchase date Agent's stamp Speedy