To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. Only use the dishwasher if all panels are properly in place. Do not tamper with the controls. Do not damage, sit or stand on the door or baskets of the dishwasher. Close the door when not in use. Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, turn on all hot water faucets and let water flow from each for several minutes before using the dishwasher. This will release any accumulated hydrogen gas. Do not smoke or use an open flame during this time. Be sure that all items placed in the dishwasher are "dishwasher safe". For items not labeled, check the manufacturers recommendations. When loading tableware, place sharp items away from the door to prevent damage to the seal. Load sharp items pointing downwards to prevent injuries. Only use detergents and rinse aids recommended for residential dishwashers. Keep all detergents and rinse aids out of the reach of children. Do not inhale or swallow detergents. Dishwasher detergents contain irritant and corrosive ingredients. They can cause burning in the mouth and throat if swallowed, or inhibit breathing. Consult a doctor immediately if detergent has been swallowed or inhaled. Do not drink water from the dishwasher! Harmful residues could be present. Do not fill the rinse aid reservoir or salt container with detergent. It will destroy the rinse aid compartment and water softener. If the power cord is damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord.

Disposal of an appliance

If the appliance is removed from its installation site and will not be used, remove the doorlock to the wash cabinet to prevent children from locking themselves in the machine.

SAVE THESE INSTRUCTIONS

Guide to the dishwasher
a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm
g Filter combination h Data plate i Optical interface j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container

Control panel

a Time display b Delay Start button d with indicator c Detergent button d Check / Refill indicators e Glasscare indicator
f Program selection g Program button h On button g / Indicator i Off button o j Optical Interface
Caring for the environment

Energy saving washing

This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source. ^ For fastest possible wash times, yet higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the baskets without overloading for the most economical washing. ^ Use the correct amount of detergent and rinse aid. ^ When using powder or gel detergent, reduce the amount to 2/3 of the normal amount when washing a small load. ^ Choose a program that best suits the degree of soiling and the type of dishes being washed. ^ For small loads select "Short".

Before using for the first time
To open the door To close the door
^ Push the baskets in. ^ Lift the door and push until it clicks into position.
^ Pull the handle to open the door. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will continue.

Water softener

Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. To achieve good cleaning results, the dishwasher needs soft water. Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4d (4 gr/gal [US]), the water should be softened. This takes place automatically in the units integrated water softener. The water softener is set automatically to the local water hardness. The water softener is designed for a water hardness of up to 70 d. If the hardness of your local supply is constantly lower than 4 d , you do not need to add water softener salt. The salt indicator turns off automatically.
Checking the water hardness
Once the dishwasher has been installed and connected, run the "Rinse + Hold" program. After the program has finished, the water hardness measured by the sensor can be displayed. This value is displayed in d and may vary depending on the water quality. ^ Turn the dishwasher off with "o". ^ Press and hold the program and "g " button simultaneously. Hold the program button until the lower right program indicator lights. If it does not come on, start over. ^ Press the "Detergent" button twice. The "Gel" indicator flashes twice in intervals. The measured water hardness is shown in the time display in the numbers following "p". ^ Turn the dishwasher off with "o".
Filling the salt container
,Inadvertently filling the salt container with dishwashing detergent will damage the water softener. ,Only use water softener salt specially formulated for dishwashers. Other salts may contain insoluble additives which can impair the water softener.
^ Remove the lower basket and unscrew the salt container lid. When opening the salt container, water will run out. Open the container only to refill salt. ^ Place the provided funnel over the salt container. Carefully fill with salt. The salt container holds approx. 4.5 lbs (2 kg) of salt. As it is filled, water will run out. ^ Clean any excess salt from the threads of the container opening. Screw the lid on firmly. ^ If the dishwasher will not be used immediately, run the "Short" program. This will remove any traces of salt from inside the wash cabinet.

Important: The salt container must be filled with 2 quarts (2 l) of water before adding salt for the first time. Water does not have to be added with subsequent refills.

Salt indicator

^ When the "Salt" indicator comes on, refill the salt after the program is finished. After the container has been filled, the water softener is automatically reactivated the next time the dishwasher is started. The "Salt" indicator will be lit during this process.

Rinse aid

Rinse aid helps to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed.
,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir.
When using "2 in 1" detergents, no rinse aid is needed. ^ Pour liquid rinse aid into the reservoir until it its visible on the surface of the screen. The rinse aid reservoir holds approx. 3.7 oz (110 ml). ^ Press on the flap until you hear it click shut. Failure to close it all the way allows water to enter the reservoir during the wash program. ^ Clean any spilled rinse aid. The flap will remain closed during normal operation.

Adding rinse aid

^ Press the button in the direction of the arrow until the flap springs open.

Rinse aid indicator

When the rinse aid indicator first comes on, there will be enough rinse aid left for 2 - 3 washes.

Adjusting the dosage

The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. Use a higher setting if spots appear on dry glassware. Use a lower setting if streaking appears on dishes or glasses. ^ Turn the dishwasher off "o". ^ Press and hold the program button and at the same time turn the dishwasher on with "g". Hold the program button until the lower right program indicator lights.
^ The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling. If the "2 in 1" function is selected, the rinse aid indicator will not light, see "Additional functions - Detergent settings".
If it does not come on, start over. ^ Press the "Detergent" button 3 times. The "Gel" indicator flashes 3 times. The time display shows "p 3" flashing. A rinse aid amount of 3 ml is selected (factory setting). The set value is shown in the time display after "p". ^ Select the desired setting with the program button. Every touch of the button adjusts the level. The dosage is saved. ^ Turn the dishwasher off "o".

* depending on model

Cutlery tray

(depending on model)

Spoons with thick handles may have to be placed as knives and forks with their heads in the holders ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles between the holders. The upper spray arm must not be blocked by tall cutlery items. The cutlery tray insert is removable.

Cutlery basket

(depending on model) Spoon inserts for the cutlery basket The supplied insert is designed to wash heavily soiled spoons. The individual slots allow the water to better reach the surface of each spoon.
^ For best cleaning results, cutlery should be placed in the basket with the handles down. Knives and forks should be loaded with the pointed end down to prevent injuries. ^ Place small spoons in the individual slots to either side of the cutlery basket.
^ Attach the insert when needed to the cutlery basket.
^ Insert the cutlery with the handles down into the insert. Arrange the cutlery evenly.

Upper basket

Coffee bar (depending on model) Glasses can be leaned against the coffee bar to allow a firm stand.
,Always use the dishwasher with
the upper and lower basket inserted.
^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans. ^ Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket.
^ The bar can also be used to separate two rows of glasses. ^ To stack wide items, flip the bar to the right. Cup racks ^ Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces.
Removable spike insert The spike insert can be removed to create more space for larger items, e.g. a saucepan. Removing the insert a:
^ To remove an insert, gently pull up on the handle. Inserting the insert b: ^ Slide the hitches of the insert under the horizontal struts of the upper basket. ^ Push down on the handle to snap the insert into position.

Normal China & Crystal

x x as required

as required

SaniWash

Rinse & Hold
Usage: Electric: 0.01 - 1.23 kWh Water: 1.3 - 6.3 gal (5 - 24 l)

Time display

Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time shown in the time display. The running time for the same program may vary depending on the intake water temperature, load size and soiling. When a program is selected for the first time, a time is shown which equals an average program running time with cold water. The time values in the program guide correspond to the program running times with standard loads and temperatures. Each time a program is run, the electronic adjusts the program running time according to the intake water temperature and the load size.

At the end of a program

At the end of a program the optical function light flashes slowly with the door closed. The time display shows "0". Dishes tends to chip if removed still hot from the dishwasher. Let the dishware cool. After turning off the dishwasher open the door slightly. The dishes will cool much faster. ^ Unload the dishwasher. The optical function light goes out one hour after the end of a program. ^ Turn the dishwasher off "o". The dishwasher continues to use electricity until turned off with the "o " button. ^ If the dishwasher is not used for a longer period of time, e.g. vacationing, turn off the water supply.

Glasscare indicator

The green Glasscare indicator lights during the China & Crystal program. This indicates that a program has been selected which washes glasses especially gently.

Interrupting a program

A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from where it was interrupted.

Changing a program

If the detergent flap is already open, do not change the program. If a program has already started and you wish to change it: ^ Open the door. ^ Press the "o" button. ^ Press the "g" button. ^ Select the desired program with the program button. ^ Close the door. The optical control lights. The program starts.
,Open the door with care. The water in the dishwasher is hot. Danger of scalding. Before closing the door again, leave it ajar for approx. 20 secs. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place.

Buzzer

A signal sounds at the end of a program and when a fault occurs. The buzzer at the end of a program sounds five times in quick succession for up to one hour. The buzzer for a fault sounds in intervals up to two minutes. The buzzer is activated by default. It can be turned off, so it does not sound at the end of a program. The buzzer for a fault cannot be turned off. ^ Open the door. ^ Turn the dishwasher off with "o". ^ Press the program button and at the same time turn the dishwasher on with "g ". ^ Hold the program button for at least 4 seconds until the lower right program indicator comes on. If it does not come on, start over. ^ Press the tab button four times. The "Gel" indicator flashes four times in intervals. The time display shows if the program end buzzer is turned on or off. "p 1": Buzzer is turned on "p 0": Buzzer is turned off ^ Press the program button to change the setting. The setting is saved. ^ Turn the dishwasher off with "o".

Default setting

All settings can be reset to the factory default. ^ Open the door. ^ Turn the dishwasher off "o". ^ Press the program button and at the same time turn the dishwasher on "g ". Hold the program button for at least 4 seconds until the lower right program indicator comes on. If it does not come on, start over. ^ Press the tab button 12 times. The "Gel" indicator flashes once long and twice short in intervals. The time display shows if a setting was changed. "p 1": All settings are factory default. "p 0": At least one setting was changed. ^ To reset the dishwasher to the factory default, press the program button. The setting is saved. ^ Turn the dishwasher off "o".
Frequently asked questions
With the aid of the following guide, minor problems can be fixed without a service call.
,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage.

Technical faults

Issue The program does not start. Possible fault The door is not properly closed. The machine is not plugged in. The fuse is defective or the breaker has tripped. The dishwasher is not turned on. The fuse has tripped. Fix Close the door firmly. Insert the plug. Reset the circuit breaker. Make sure it is a 15 A breaker. Press "g " and select a program. Reset the circuit breaker. Make sure it is a 15 A breaker. Install the reflector properly, see Installation sheet.
The dishwasher stops during a program.
The optical indicator is not The reflector was visible when a program not properly has started. installed.
Issue Possible fault Fix Turn the dishwasher off "o". After a few seconds: Turn the dishwasher on. Select the desired program with the program button. Close the door. If the problem persists call Technical Service. Turn off the water supply. Call Miele Technical Service. The optical indicator There may be a flashes. technical fault. The buzzer sounds. All program indicators are flashing fast when the door is open. The time display shows FXX. The drain pump is running when the door is opened. Fault F70: The waterproof system has activated.
Problems water intake/drain
Issue Possible fault Fix The optical indicator The water supply Open the water supply. flashes. is shut off. The buzzer sounds. The "Intake/Drain" indicator flashes when the door is open. Before fixing the fault: The dishwasher stops. The optical indicator Turn the dishwasher off "o". flashes. Fault F12/F13: Open the water supply. The buzzer sounds. Water intake fault Clean the water intake filter, The "Intake/Drain" see "User Maintenance indicator flashes when the Instructions". door is open. The water pressure at the The time display shows water connection is lower FXX. than 4.35 psi. Consult a plumber. Fault F11: Water See "User Maintenance Instructions". drain fault. There may be Clean the triple filter. water in the wash Clean the drain pump and the cabinet. non-return valve. Remove any kinks in the drain hose.
General problems with the dishwasher
Issue Detergent is left in the dispenser at the end of a program. The detergent lid cannot be closed properly. The door and the interior walls are still wet after a program has finished. Water remains in the wash cabinet at the end of a program. Possible fault The dispenser was damp when detergent was added. Detergent residue is blocking the catch. Fix Dry the dispenser before adding detergent. Remove the residue.
This is not a fault! It is the The moisture will evaporate normal operating mode of after a short time. the drying system. Before fixing the fault: Turn the dishwasher off "o ". The triple filter in the wash Clean the triple filter. See cabinet is clogged. "User Maintenance Instructions". The drain pump or the Clean the drain pump and non-return valve may be the non-return valve, see blocked. "User Maintenance Instructions". The drain hose is kinked. Remove any kinks from the drain hose.

Issue Possible fault Fix Use a different detergent. Glasses are Detergent deposits. discolored and the film cannot be wiped off. Glasses are dull and discolored, film cannot be wiped off. Tea or lipstick stains have not been completely removed.
Glasses are not dishwasher There is no remedy. Only safe. wash dishwasher safe glasses in the dishwasher. The wash temperature of Select a program with a higher temperature. the selected program was too low. The detergent has a low Use a different detergent. bleaching effect. Plastics are Natural dyes e.g. from Use more detergent, see "Adding detergent". discolored. vegetables may be the cause. Not enough Discoloration is permanent. detergent was used to break down natural dyes. There are rust stains The affected items are not There is no remedy. Only on cutlery. corrosion resistant. wash dishwasher safe cutlery in the dishwasher. No program was run after Start the "Short" program refilling salt. Salt residuals without a load after refilling got in the wash cycle. salt. The salt container lid was Reseat and screw the lid on not screwed on properly. firmly.

After sales service

Repairs
In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door.

MieleCare

MieleCare, our Extended Service Contract program, gives you the assurance of knowing that your appliance investment is covered by 5 years of worry free ownership. MieleCare is the only Extended Service Contract in the industry that guarantees repairs by a Miele Authorized Service Provider using genuine Miele parts. Only genuine Miele parts installed by factory trained professionals can guarantee the safety, reliability, and longevity of your Miele appliance. Please note that unless expressly approved in writing by Mieles Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home. To learn more about MieleCare Extended Service Contracts, please contact your appliance dealer or visit us online at: www.store.miele.com

PC Update

The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology. When, for example, technological developments offer advanced modifications to your existing program cycles a service technician will be able to input these into your machine controls via the indicator light marked PC. Miele will provide information when such possibilities become available.

Transport

To transport the dishwasher, e.g. when moving to a new home, note the following: Empty the dishwasher. Secure any loose parts, e.g. hoses, cables, cutlery baskets. Transport the dishwasher in the upright position. If unavoidable it may be transported on its back. Do not transport it on its side or on the door. Residual water in the machine could leak and cause electrical damage.

User Maintenance Instructions
To prevent accidents and machine damage, read these instructions before installation or use.

Cleaning and Care

Indicator reflector
Check and clean your dishwasher regularly (approx. every 4-6 months). This will help avoid faults and problems. The reflector of the optical indicator is located in the steam deflector beneath the counter top. To clean the reflector, remove it from the plastic bracket. ^ Open the door and remove the reflector from the bracket. ^ Clean the reflector and the plastic bracket with a damp cloth. ^ Return the reflector to the bracket.
,Abrasive cleaning agents, glass cleaning agents, all-purpose cleaners, thinner or ammonium cleaners should not be used on the dishwasher. They will damage the surface.

Wash cabinet

Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. The wash cabinet can be cleaned with a dishwasher cleaner such as "Dis Cleaner" available from your Miele dealer, Miele or online at www.miele.com.
^ Clean the control panel with a damp cloth.

Exterior

^ Use a conditioner suitable for your kitchen cabinetry. ^ Clean wood with a damp cloth and wipe dry. ^ Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner or with dishwashing detergent and warm water. ^ To help prevent resoiling, a conditioner for stainless steel can also be used. Apply sparingly with even pressure.

Door and the door seal

^ Wipe the door seals regularly with a damp cloth to remove food deposits. ^ Food residue and spilled liquids should be wiped from the sides of the dishwasher door. These are outside of the wash cabinet and are not cleaned by water from the spray arms.

Triple filter system

The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones).

,The machine must not be used without all the filters in place!
^ Check and clean the filter system every 4-6 months or whenever a foreign object is trapped. The level of soiling and time it takes before the filters need cleaning will vary depending on your household. ^ Turn off the dishwasher before cleaning. ^ Turn the handle counterclockwise to release the triple filter system. ^ Lift the filter combination out of the machine. Remove any solid particles and rinse under running water. Scrub with a nylon brush if necessary.
To clean the inside of the filter, the flap must be opened. ^ Push the clips together a and open the flap b. ^ Rinse under running water. ^ Close the flap so that the clip engages.
^ Return the filter so it lies flat in the base of the wash cabinet. ^ Lock the filter by turning the handle clockwise.
,The triple filter system must be
inserted and locked. Large particles could get in the circulation system and cause a blockage.

Cleaning the spray arms

Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Press the top spray arm up to engage the inner ratchet and unscrew the spray arm.
^ Pull the lower spray arm firmly upwards to remove.
^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
^ Use a pointed object such as a toothpick to push food particles into the spray arm jets. ^ Rinse thoroughly under running water. ^ Return the spray arms and check that they rotate freely.
Cleaning the water inlet filter
A filter is incorporated into the intake hose attached to the dishwashers shut off valve. If your water is hard or the pipes contain sediment, this filter may clog and prevent enough water from entering the wash cabinet.
,The plastic housing of the water connection contains electrical wiring. Do not submerge the housing in liquid. Do not cut the intake hose or submerge it in liquid.

Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician. GROUNDING INSTRUCTIONS THIS APPLIANCE MUST BE GROUNDED. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for the electrical current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
,Improper connection of the
equipment grounding conductor can result in electric shock. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Mieles Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle.

Plumbing

Connection to the water supply
,Do not drink water from the dishwasher!
The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot or cold water source. For lowest energy consumption connect the dishwasher to a cold water source. For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. All programs use hot water in the rinse cycles. The inlet hose is approximately 5 ft. (1.5m) long. A 5 ft. (1.5m) extension hose is available from the Technical Service Parts Department at the phone number listed on the back of this manual. The water inlet hose comes equipped with a 3/4" female hose thread connector. This can be directly connected to a water supply with 3/4" MHT (male hose thread ends). Water pressure: Must be between 4.5 - 145 psi (0.3 - 10 bar).
,Do not cut the intake hose. It
contains electrical wiring. If the hose is cut, the dishwasher will not work. There will be a waterleak and you could be injured. If the hose is too long, coil it neatly and place it behind the machine.

Drainage

The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39" (1 m). If the hose is to be directly fitted to the drainage outlet on site, use the supplied hose clip. The hose can be installed to the left or right side. The existing drain pipe for the drain hose is designed for various hose diameters. The drain pipe must be shortened if the drain pipe extends too far into the drain hose. The drain hose could get clogged. The drain hose must not be shortened. Make sure the hose is installed without kinking, pressure or being pulled. Venting the drainage system If the dishwasher drain hose is connected to a floor drain or to a drain pipe that is less than 8" (20 cm) above the floor, the drain must be vented. Otherwise the water inside the dishwasher may siphon out during the wash program. ^ Open the dishwasher door and remove the lower basket. ^ Pull the lower spray arm firmly upwards to remove.
^ Cut off the vent cap located at the right rear of the triple filter system, as illustrated.
Alterations reserved/4906 G 1470 Vi G 2470 Vi

M.-Nr. 060 / 03 en - US

ENERGY STAR Qualified Appliance Product List Updates December 2006 The appliance models listed in this document were either added to the qualified product list, deactivated from the qualified product list, or had their product specifications changed in the month of December. Deactivated products will remain on the qualified list in red for a year. If you have questions concerning this list, please contact David Ryan (dryan@drintl.com) or Josh Butzbaugh (jbutzbaugh@drintl.com) at 301-588-9387. ENERGY STAR Qualified Clothes Washers New: Huebsch FTZA0*** Huebsch FTZA1*** Huebsch HTE*77*** Huebsch HTG*79*** Huebsch HWF*7**** Huebsch HWR*7**** Huebsch LTZA0*** Huebsch LTZA7*** Huebsch LTZA9*** Kenmore 4708#60** Kenmore 4709#60** Kenmore 4996#60** Kenmore 4997#60** LG Electronics WM133#H* LG Electronics WM2496H** Speed Queen ATSA0*** Speed Queen ATSA5*** Speed Queen CTSA0*** Speed Queen CTSA7*** Speed Queen CTSA9*** Speed Queen FTSA0*** Speed Queen FTSA1*** Speed Queen LTSA0*** Speed Queen LTSA5*** Speed Queen LTSA7*** Speed Queen LTSA9*** Speed Queen STE*77*** Speed Queen STG*79*** Speed Queen SWF*7**** Speed Queen SWR*7**** Unimac FTUA0*** Unimac FTUA1*** Unimac LTUA0*** Unimac LTUA7*** Unimac LTUA9***
ENERGY STAR Qualified Appliance Product List Updates December 2006 Page 1
Whirlpool Whirlpool Whirlpool Changed:
WFW9200T*#** WFW9400T*#** WFW9600T*#**
Fisher & Paykel GWL15 (WF changed from 8.14 to 7.19, kWh/yr changed from 212 to 220) Fisher & Paykel IWL16 (WF changed from 8.26 to 6.86; kWh/yr changed from 223 to 219; MEF changed from 1.91 to 2.00) LG WM207#C* (Volume changed from 3.22 to 3.32; WF changed from 3.89 to 3.78; MEF changed from 2.029 to 2.35; kWh/yr changed from 195 to 159) LG WM2277H* (Volumed changed from 3.21 to 3.32; WF changed from 4.2 to 3.63; MEF changed from 1.96 to 2.42; kWh/yr changed from 253 to 171) Maytag MFR18PD (model number changed from MFR18PDCWS to MFR18PD; MEF changed from 1.59 to 1.753; MF changed from 6.33 to 6.656) Maytag MFR25PD (model number changed from MFR25PDCWS to MFR25PD; MEF changed from 1.45 to 1.734; MF changed from 7.03 to 6.47) Maytag MFW9600#** (model number changed from MFW9600*+ to MFW9600#**; MEF changed from 1.78 to 1.95; WF changed from 4.38 to 4.54; kWh/yr changed from 287 to 218; volume change from 3.30 to 3.29) Maytag MFW9700#** (model number changed from MFW9700*+ to MFW9700#**; MEF changed from 1.85 to 2.12; WF changed from 4.27 to 4.38; kWh/yr changed from 311 to 212; volume change from 3.30 to 3.29) ENERGY STAR Qualified Refrigerators New: Element LECR23EFE Frigidaire FRS3HR5H* Frigidaire FRS3LR5E Frigidaire FRS6HR4H* Frigidaire FRS6HR5H* Frigidaire GLHS36EF* Frigidaire GLHS38EG* Frigidaire GLHS38EGW* Frigidaire PHSC39EGS* Frigidaire PLHS67EH* Gallery GLHS65EH* Kenmore 4433*6* Kenmore 4450*6* Kenmore 5710*60* Maytag MCD2257KE* Whirlpool GC5NHA*S*0* Deactivated: Amana ABB2224DE* Amana ABB222ZDE*
ENERGY STAR Qualified Appliance Product List Updates December 2006 Page 2
Amana ABB2524DE* Amana ASD2324HE* Amana ASD2326HE* Amana ASD2328HE* Crosley CS26G9D* Jenn-Air JB*2086HE* Jenn-Air JB*2256HE* Jenn-Air JCD2292HT* Jenn-Air JCD2295HES Jenn-Air JSD2789HE* Kenmore 5346* Kenmore 5565* Kenmore 5566* Kenmore 6533* Kenmore 6690* Kenmore 6694* Kenmore 6695* Kenmore 6699* Kenmore 6725* Kenmore 7550* Kenmore 7551* Kenmore 7552* Kenmore 7553* Kenmore 7650* Kenmore 7651* Kenmore 7652* Kenmore 7653* KitchenAid KBLA20EM* KitchenAid KBLA22KM** KitchenAid KBRA20EM* KitchenAid KBRA22KM* KitchenAid KBRP20EM* Maytag MBB1954HE* Maytag MBF1956HE* Maytag MBF2256HE* Maytag MBF2258HE* Maytag MBF2556HE* Maytag MBF2558HE* Maytag MFD2560HE* Maytag MFF2559HE* Maytag MSD2355HE* Maytag MSD2357HE* Maytag MSD2433HE* Maytag MSD2434HE* Maytag MSD265RHE* Maytag MSD2734HE* Maytag MZD2665HE* Maytag MZD2667HE* Maytag PBF2253HE*
ENERGY STAR Qualified Appliance Product List Updates December 2006 Page 3
Maytag Maytag Maytag Maytag Maytag Maytag Whirlpool Changed:
PBF2255HE* PDF1951KE* PSD263LHE* PSD266LHE* PSD267LHES PSD269LHE* GB9SHKRM*
Frigidaire FRX1HR58E* (reactivated) Kenmore 5533*6* (volume changed from 26 to 25.9; kWh/yr changed from 619 to 617.945) Maytag MFF2558HE* (model number changed from MFF2557HE* to MFF2558HE*) Moffat MSR23IET (brand name changed from Mabe to Moffat)
ENERGY STAR Qualified Dishwashers New: Adora EDW5***N Adora GHDA4**N Adora GHDA6**N Eterna EDW6***N Frigidaire FBD1500LF** Frigidaire FDB1500LF** Frigidaire FDB1501FB** Frigidaire FDB2000RF** Frigidaire FDB700BF Frigidaire GLD2250RD** Frigidaire GLD2875FP General Electric GLD4***N General Electric GLD5***N General Electric GLD6***N General Electric GSD31***N General Electric GSD69**N Hotpoint HLD4***N Kenmore 1525*40* Kenmore 1625*40* Monogram ZBD07**N Monogram ZBD68**N Profile PDW7***N Profile PDW98**N Deactivated: Frigidaire Frigidaire Frigidaire FDB2810LD FDBB840D FDP750RC

Page 4

ENERGY STAR Qualified Appliance Product List Updates December 2006
Frigidaire Frigidaire Changed:

GLD2870R PLD2875R

Frigidaire FDB1501FB** (model number changed from FDB1501BF** to FDB1501FB**) Frigidaire FDBB2040F** (model number changed from FDBB2040F to FDBB2040F**; EF changed from 0.63 to 0.66; kWh/yr changed from 343 to 329) Miele G2020 (kWh/year changed from 345 to 320, Energy Factor changed from 0.63 to 0.67) Miele G2170 (kWh/year changed from 345 to 320, Energy Factor changed from 0.63 to 0.67) Miele G1180 (kWh/year changed from 339 to 318, Energy Factor changed from 0.64 to 0.68) Miele G1470 (kWh/year changed from 339 to 318, Energy Factor changed from 0.64 to 0.68) Miele G2140 (kWh/year changed from 339 to 318, Energy Factor changed from 0.64 to 0.68) Miele G2150 (kWh/year changed from 339 to 318, Energy Factor changed from 0.64 to 0.68) Miele G2180 (Energy Factor changed from 0.64 to 0.68) Miele G2420 (Energy Factor changed from 0.64 to 0.68) Miele G2430 (Energy Factor changed from 0.64 to 0.68) Miele G2470 (Energy Factor changed from 0.64 to 0.68) Miele G1150 (Energy Factor changed from 0.64 to 0.68)
ENERGY STAR Qualified Room Air Conditioners New: Arctic King MWF-25CR General Electric AJCH10ACCM2 General Electric AJCH10DCCM2 General Electric AJCQ06LCCM1 General Electric AJCQ08ACCM1 General Electric AJCQ10ACCM1 General Electric AJCQ10DCCM1 General Electric AJCQ12DCCM1 General Electric AJCS10ACCM2 General Electric AJCS10DCCM2 General Electric AJHS08ASCM1 General Electric AJHS08DCCM1 General Electric AJHS10DCCM1 Polar Wind MWF-08CR Polar Wind MWF-10CR Polar Wind MWF-12CR Sunbeam SCA063REC1 Sunbeam SCA083RAC1 Sunbeam SCA083REC1 Sunbeam SCA083RKC1 Sunbeam SCA103RAC1 Sunbeam SCA103RAC2 Sunbeam SCA103REC1 Sunbeam SCA123REC1
ENERGY STAR Qualified Appliance Product List Updates December 2006 Page 5
Sunbeam Sunbeam Sunbeam Westpointe Westpointe Westpointe Westpointe
SCA153REC1 SCA183REC2 SCA253REC2 MWF-12CR MWF-15CR MWF-18CR MWF-25CR

Page 6