Miele W 1714
Here you can find all about Miele W 1714 like manual and other informations. For example: review.
Miele W 1714 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Miele W 1714 please write about it to help other people. [ Report abuse or wrong photo | Share your Miele W 1714 photo ]
Miele W 1714 Washing Machine, size: 1.1 MB
Miele W 1714
Miele Softtronic W 1714
User reviews and opinions
No opinions have been provided. Be the first and add a new opinion/review.
~ If the connection cable is faulty it
~ The electrical safety of this washing
~ In the event of a fault or for cleaning
~ This washing machine must only be
connected to the on-site water supply using a new hose kit. Old hoses must not be re-used.
~ Do not connect the washing machine to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating). ~ Faulty components must only be replaced by genuine Miele original spare parts. Only when these parts are fitted can the safety standards of the machine be guaranteed.
~ In countries where there are areas
which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the machine and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.
Warning and Safety instructions ~ This washing machine may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer.
washing machine, unless authorised to do so by Miele.
~ Turn off the stopcock if the machine
is to be left for any length of time (e.g. holiday), especially if there is no floor drain (gully) in the immediate vicinity.
~ Do not make any alterations to the
~ Flooding danger.
~ Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst or split. The reliability of the electronic control unit may be impaired at temperatures below freezing point. ~ Before using the washing machine for the first time, check that the transit bars at the rear of the machine have been removed (see section on "Installation"). During spinning, a transit bar which is still in place may result in damage to both the machine and adjacent furniture or appliances.
If hooking the drain hose into a wash basin, check that the water can drain off quickly enough to prevent the sink from overflowing. Make sure the drain hose is secure, so that the force of the water flowing out of the hose does not dislodge it. objects (e.g. nails, pins, coins, paper clips) do not find their way into the machine with the laundry. These may damage components of the machine (e.g. suds container, drum), which in turn can result in damage to the laundry. dispensed, the machine should not need to be descaled. If, however, you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. A special descaling agent is available to order from the Miele Spare Parts Department or via the internet on www.miele-shop.com.
~ Take care to ensure that foreign
~ If the correct amount of detergent is
Warning and Safety instructions ~ Textiles which have been pre-treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine. ~ Never use solvent based cleaning agents, e.g. those containing benzene, in this machine, as this may result in damage to component parts and create toxic fumes. Such agents also pose a fire and explosion hazard. ~ Never use solvent based cleaning agents, e.g. those containing benzene, to clean the outside surfaces of this machine. They can cause damage to plastic surfaces. ~ Only use dyes specified by the manufacturer as being suitable for use in a domestic washing machine. Always observe the manufacturer's instructions carefully. ~ Colour run and dye removers contain sulphur compounds which can cause damage such as corrosion. Do not use these products in this machine. ~ If liquid detergent comes into contact with the eyes, rinse them thoroughly with lukewarm water immediately. If swallowed, seek medical assistance immediately and retain the packaging or label for reference. Those with skin problems or sensitive skin should avoid their skin coming into contact with liquid detergent. ~ Only remove laundry from the
washing machine once the drum has stopped turning. Reaching into a moving drum is extremely dangerous and could result in injury.
~ Accessory parts may only be fitted
when expressly approved by Miele. If other parts are used, guarantee, performance and product liability claims will be invalidated.
Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Operating the washing machine
a Display See the following page for more information. b Temperature button For selecting a temperature. c Spin speed button For selecting the final spin speed or e (Rinse hold) or deselecting the spin No u. d PC / Optical interface This is used by service technicians to run diagnostic checks on your machine and can also be used to update programming data in the future.
e Start/Stop button For starting the programme selected and cancelling a programme once it has started. f Extra option buttons Various Extra options can be added to the washing programmes. g Programme selector For selecting a programme. The indicator light next to the selected programme will come on. The programme selector can be turned clockwise or anti-clockwise. h Door button Opens the machine door. i I-On/0-Off button For switching the machine on or off.
Washing environmentally and economically
Energy and water consumption Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using. Use the Automatic and Express programmes for small loads. When smaller amounts of laundry are washed using the Cottons programme, the automatic load recognition system will reduce the amount of water, time and energy used. This may mean that the time left shown in the display is adjusted during the course of the wash programme. Using the Cottons 60C programme, instead of the Cottons 95C programme will give energy savings of between 35% and 45%. This is sufficient for most levels of soiling. Detergent Do not exceed the amounts of detergent recommended by the manufacturer on the packaging. Adjust the dosage to the degree of soiling of the laundry. Reduce the amount of detergent with smaller loads (approx. 1/3 less than the amount recommended can be used when washing a half load). Choosing the correct extra option (Short and Pre-wash) Select: A wash programme together with the Short extra option for light to normal soiling where there are no obvious marks. A wash programme without any extra options for normal to heavy soiling with visible staining. The Pre-wash extra option for laundry with large amounts of dirt (e.g. dust, sand). When drying with a tumble dryer Selecting the highest possible spin speed for the wash programme will save energy when drying in a tumble dryer afterwards.
How to wash correctly
The headings numbered A, B, C,. show the operating sequence and can be used as brief instructions. A Sort the laundry
,If you use a solvent-based clean-
ing agent (e.g. one containing benzene) to pre-treat a stain, make sure that any plastic parts (e.g. buttons) are protected, and that the cleaning agent is rinsed off before washing the garment in the machine.
,Do not use solvent-based
cleaning agents in this machine.
^ Sort the laundry by colour and by care label. Most garments have a textile care label in the collar or side seam. Dark textiles often contain excess dye and should be washed separately several times before being included in a mixed load. Always wash whites and coloureds separately. Curtains: Remove lead weights first or place in a laundry bag. Underwiring and collar stiffeners: Any loose wiring in bras, shirt collar stiffeners, etc. should be removed or sewn in. Knitted garments, trousers and jeans, T-shirts and sweat shirts: Turn inside out, if recommended by the manufacturer. Close any zips, fasten hooks and eyes etc before washing. Fasten duvet covers etc. to prevent small items from being rolled up inside them. Do not wash any items in this machine which are specified by the manufacturer as not washable on the care label. (h symbol)
^ Empty all pockets.
,Foreign objects (e.g. nails, coins, paper clips, etc.) can cause damage to garments and components in the machine.
^ Badly soiled areas, stains etc. should be cleaned as soon as possible, preferably whilst still fresh. Spillages should be carefully dabbed off using a soft colourfast cloth. Do not rub! Badly soiled areas can be pre-treated with liquid detergent, stain removers etc. first, following the manufacturer's instructions. With particularly stubborn stains ask your dry cleaner for advice.
B Switch on the washing machine C Load the drum ^ Press the Door button to open the drum door. ^ Unfold the laundry and load loosely in the drum. Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning. The most efficient use of energy and water is achieved when a full load is washed. However, do not overload as this causes creases and reduces cleaning efficiency. Make sure that no garments are caught between the drum door and seal. D Select a programme
^ Turn the programme selector clockwise or anti-clockwise to the required programme. The programme indicator light for the programme selected will come on. E Select a temperature / spin speed The suggested temperature and/or spin speed can be changed.
^ Press the Temperature button to alter the temperature and press the Spin speed button to alter the spin speed.
^ Shut the door with a gentle swing.
F Select an extra option(s) Water plus The water level in the main wash and the rinses will be increased if the Water plus option is selected. However, you can select other settings for Water plus. These are described in "Programmable functions". Pre-wash For laundry with large amounts of dirt e.g. dust, sand. ^ Select any extra options by pressing the appropriate button. The relevant indicator light will come on to show which extra option has been selected. Not all the extra options are suitable for use with every programme. You can only select extra options which are compatible with the basic programme being used. Short For light to normal soiling with no visible staining. The duration of the main wash is reduced. Buzzer An audible tone sounds repeatedly at the end of a programme and when Rinse hold is reached. The buzzer will sound repeatedly until the machine is switched off. The volume of the buzzer can be changed, see "Programmable functions".
G Add detergent It is important to dispense the correct amount, because. too little detergent results in: Laundry not getting properly clean and with time it may become grey and hard to the touch. Greasy particles clinging to the laundry. Limescale deposits on the heater elements. too much detergent results in: Excessive foam which causes a low level of agitation and poor wash, rinse and spin results. Higher water consumption (an additional rinse cycle will automatically switch in). A burden to the environment. ^ Pull out the detergent drawer and place detergent in the compartments as follows: i Detergent for the pre-wash (divide the total recommended amount as follows: add 1/3 to compartment i and 2/3 to compartment j) j Detergent for the main wash Fabric conditioner or liquid starch ^ Close the detergent drawer. See "Detergent" for further information.
H Start the programme ^ Press the flashing Start/Stop button. The estimated programme duration will appear in the display once the programme has started. During the first 8 minutes the machine measures how much water is being absorbed by the laundry. The programme duration may be longer or shorter depending on this absorbency rate. The programme sequence is also shown in the display. The washing machine shows you when each section of the programme is reached. I Remove the laundry when the programme has finished In the anti-crease phase after the programme has finished, the following will appear alternately in the display:
Check that all items have been removed from the drum. Items left in the drum could discolour other items in the next wash or become discoloured themselves.
^ Check the folds in the door seal for any small articles, e.g. buttons which might be lodged there. ^ Switch the machine off with the I-On/0-Off button.
^ Press the Door button to open the drum door. ^ Remove the laundry.
^ Close the drum door. Otherwise there is the danger of objects being placed inadvertently in the drum. If these remained unnoticed and were washed in the next load, they could damage the laundry.
Final spin speed
Programme Cottons Minimum iron Delicates Woollens Express Automatic Shirts Denim Dark garments Spin rpm 1200 1400
To omit the final spin (Rinse hold) ^ Select the e setting using the Spin speed button. The laundry will not be spun and will remain suspended in the final rinse water. This reduces creasing if the laundry is not going to be removed from the drum immediately after the end of the programme. To start the final spin: The washing machine will display the maximum spin speed possible. You can select a spin speed lower than this. Start the final spin by pressing the Start/Stop button. To end the programme: Press the Door button. The water will drain away. Press the Door button again to open the door. To omit rinse and interim spin and the final spin (No u) ^ Select the No u setting using the Spin speed button. The laundry is not spun after the final rinse. The water will drain away and the machine will go straight into the anti-crease stage. An additional rinse is introduced if this setting is selected with the Cottons, Minimum iron, Express and Automatic programmes.
You can reduce the final spin speed. However, you cannot select a final spin speed higher than that shown in the chart above. Rinse and interim spin There is a spin after the main wash and between the rinses. A reduction in the final spin speed will also reduce the interim spin speed. If a spin speed of less than 700 rpm is selected for a Cottons programme, an additional rinse is introduced.
Cottons 98E76* Fabric 30C to 95C Max. load 6.0 kg
Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, underwear, T-shirts etc.
The safety lock prevents the machine from being opened and programmes from being cancelled during a wash programme. To activate the safety lock ^ Press and hold in the Start/Stop button after the programme has started.
Stop or in 3 secs 0
^ Keep the Start/Stop button pressed in until the time has elapsed and the following appears in the display:
The safety lock is now activated. It is deactivated automatically at the end of the programme. To deactivate the safety lock ^ Press and hold in the Start/Stop button after the programme has started.
Unlock in 3 secs 0
The correct detergent
All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads. Some tablets do not dissolve as rapidly as others, and may not be suitable for programmes with short durations. Do not use biological detergents on silk as the enzymes may damage the silk! Instructions for use and recommended dosage amounts are given on the detergent packaging. Liquid detergent should be dispensed using a ball provided by the manufacturer for programmes without a pre-wash. For programmes with a pre-wash you will need to purchase a special container from the Miele Spare Parts department which sits in the main wash compartment j of the detergent dispenser drawer. Add liquid detergent to this container for the main wash and to compartment i for the pre-wash. All purpose detergent for whites* Cottons Minimum iron Delicates Woollens Express Automatic Shirts Denim Dark garments 1) Only use liquid detergent * Powder detergent, tablet detergent, liquid detergent and liquid tab detergent. X X X X X X X1) X1) X X Detergent for coloured fabrics* X X X Liquid detergent for machine-washable woollens Detergent for delicates
The right amount to dispense will depend on the following: The quantity of laundry The soiling level of the laundry Lightly soiled No visible dirt or stains. Possibly slight body odour. Normally soiled Visibly dirty and/or just a few slight stains. Heavily soiled Visible dirt and stains and/or dried on soiling. The water hardness level. Check with your local water supplier if you do not know the hardness level in your area.
A water softener can be used to cut down on the use of detergents in hard water areas. Dispense according to the amount specified on the packaging. First add detergent and then the water softener. Miele branded water softening tablets are available from the Miele Spare Parts Department or via the internet on www.miele-shop.com. Use a quantity of detergent as for soft water. Miele do not recommend connecting the machine to a household water softener.
Washing with several components
If you wash using several components (e.g. special application detergents), we recommend always dispensing the agents into compartment j in the following order: 1. Detergent 2. Water softeners 3. Stain remover This way the agents are distributed more evenly.
Fabric conditioners and liquid starch
Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stiffens and gives body to items of laundry, e.g. shirts, tablecloths and bed linen. Automatic dispensing of fabric conditioner or liquid starch to laundry at the end of a programme If starching frequently, thoroughly clean the dispenser compartment, especially the siphon tube and the fabric conditioner channel, regularly. See "Cleaning the detergent dispenser drawer". Do not use powder starch formulations or viscous liquid starch in the compartment as it will clog up.
Colour run and dye removers / dyes
^ Do not use colour run or dye removers in this machine. ^ Dyes suitable for use in domestic washing machines can be used. However, please note that the salt used in the dyeing process can cause corrosion to stainless steel components in the machine if you dye frequently. Always observe the manufacturer's instructions carefully.
^ Add the fabric conditioner or liquid starch to compartment. Do not exceed the maximum level mark. It will be automatically dispensed in the last rinse. At the end of the programme a small amount of water remains in the fabric conditioner compartment.
Cleaning and care ,Disconnect the machine from the
Extra cleaning Carry out a hot wash (70C or above) with powder detergent approx. every 6 weeks to help prevent deposits building up in the machine. These can occur when washing is mainly done at low temperatures, and also lead to unpleasant smells. If you have no reason to wash occasionally at this high temperature, then run a Cottons 95C programme with detergent but no laundry at regular intervals.
^ Remove the rubber seal 1 from the recess. ^ Using pointed pliers, take hold of the plastic filter bar 2, remove the filter and clean it. ^ Put the filter and seal back in the reverse order and reconnect the hose. ^ Turn on the stopcock and check the connection is watertight. If it leaks, tighten the connection.
Problem solving guide
With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
The programme does not start
Problem Possible cause Remedy Check whether the mains plug is plugged in and switched on. the fuse or circuit breaker has tripped. The display remains There is no power to dark, and the the machine. Start/Stop button indicator light does not come on.
You are asked to enter Access via a code has Enter the code and confirm a code. been activated. the entry. Deactivate the code if you do not wish this message to appear in the display the next time the machine is switched on. The display is dark. The display has switched off automatically to save energy (Standby mode). Press a button. Standby comes to an end.
Fault messages in the display
; lights up in the display and Drain fault
; lights up in the display and Water inlet fault
The water outlet is Clean the drain filter and blocked or the drain pump. restricted. The maximum delivery head is 1 m. The drain hose has been fixed too high. The water inlet is blocked or restricted. Check whether the stopcock is opened properly. the inlet hose is kinked. the water pressure is too low. Call the Service Department.
; lights up in the display and Waterproof fault
The water protection system has reacted.
; lights up in the display and Technical fault
There is a fault.
Start the programme again. If the fault message appears again, contact the Service Department. Use less detergent next time and follow the manufacturer's instructions on dosage given on the packaging.
A stale smell is in the drum and on laundry. White residues which look like powder detergent are seen on dark textiles after washing.
Try and brush off the residues The detergent contained compounds with a soft brush once the (zeolites) to aid water laundry is dry. softening which are Wash dark textiles using a not soluble in water. detergent which contains no They have ended up zeolites. Liquid detergents on the laundry. usually contain no zeolites. Use the Dark garments programme. Reduce quantity of clothes in drum.
Clothes are coming Programme was out creased. overloaded.
Check care labels and the The wrong programme was used. programme chart. Use easy iron conditioners.
The drum door does not open when you press the Door button
Possible cause Remedy The machine is not Insert the plug in the socket and switch on and/or connected to the switch the machine on with the I-On/0-Off button. electricity supply and/or is not switched on. The safety lock has been activated. Access via a code has been activated. Power cut. Deactivate the safety lock as described in "Changing the programme sequence - Safety lock". Deactivate the code as described in "Programmable functions - Code". Open the drum door as described in the next section.
The door was not correctly Press hard against the lock side of the drum door engaged. and then press the Door button. There is still water in the drum and the machine is unable to drain. Clean the drain filter and drain pump as described in the next section.
For safety reasons the drum door cannot be opened if the suds temperature is higher than 55C.
Opening the drum door in the event of a blocked drain outlet and/or power failure
^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine.
,Caution: if laundry has been
washed at a high temperature, water draining out of the machine will still be hot. Danger of scalding!
Procedure for draining the machine ^ Place a suitable container under the access flap. When draining water from the machine, do not unscrew the drain filter completely or take it right out.
^ Remove the lever.
A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Please note the following points: ^ The machine must be level and securely positioned. ^ To avoid vibrations during spinning, the machine should not be installed on soft floor coverings. If installing on a wooden joist floor: ^ We recommend a plywood base (at least 59x52x3 cm). The base should span several joists and be bolted to the joists and not only to the floorboards. Check for the presence of pipes and cables first. If possible, install the machine in a corner, as this is usually the most stable part of the floor. Transporting the machine to its installation site To manoeuvre the machine out of its packing case to its installation site, hold it by the front feet as well as by the edge of the lid where it protrudes to the rear of the washing machine.
,Ensure that the machine feet and
the floor are dry to prevent the machine from slipping during the spin cycle.
Removing the transit fittings
,If the machine is installed on a raised plinth, it has to be secured against slippage during spinning using retaining clips (available from the Miele Spare Parts Dept).
^ To remove the left and right covers 1. Use a screwdriver to prise out the cover as illustrated. 2. Pull the cover forwards to remove.
^ Using the spanner supplied, turn the left-hand transit bar 90, then
^ Turn the right-hand transit bar 90, then
^ withdraw the transit bar.
Installation and connection ,To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed.
^ Secure the transit bars to the back of the washing machine. Make sure that holes b are fitted over retainers a.
,The machine must not be moved
^ Fit the covers onto the two holes. Then plug the holes as shown with the caps. without the transit bars in place. Store them as shown or keep them in a safe place for future use. They must be re-fitted if the machine is to be moved again (e.g. when moving house).
Re-fitting the transit bars
Re-fitting is carried out by reversing the procedure.
Levelling the machine
The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine. All four feet are screwed in when the machine is delivered.
^ Use a spirit level to check the machine is standing level. ^ Hold foot 1 securely with a pipe wrench. Turn counter nut 2 again using the spanner supplied until it sits firmly up against the housing.
,All four counternuts must be
firmly up against the housing. Please also check this for the feet which did not need adjustment. Otherwise there is the danger of the machine moving about.
^ Using the spanner supplied turn counter nut 2 in a clockwise direction. Then turn counter nut 2 together with foot 1 to unscrew.
Building under a worktop Washer-dryer stack A Miele tumble dryer can be stacked with the washing machine. A WTV stacking kit is necessary which can be purchased from your Dealer or the Miele Spare Parts Department. Please note:
,The machine lid must not be
This washing machine can be pushed under a worktop with its lid in place, providing the worktop is high enough.
a Safety distance to wall: at least 2 cm b Height: Stacking kit with pull-out shelf: approx. 172 cm Stacking kit without pull-out shelf: approx. 170 cm c Depth of the washer-dryer stack: approx. 65 cm
The Miele water protection system
The Miele water protection system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose 1) Inlet hose The inlet hose can withstand pressure of more than 7,000 kPa. 2) Electronic unit and washing machine housing Sump Any leaking water is collected in a sump in the base of the machine. A float switches off the safety valves, preventing any more water flowing into the machine and water in the suds container is pumped away. Overflow protection This prevents the washing machine taking in too much water. If the water level exceeds a certain level, the drain pump switches in and pumps the excess water away. 3) Drain hose The drain hose is protected by a ventilation system which prevents the washing machine from being emptied completely.
Connection to the water supply
The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washing machine has been designed to comply with DIN regulations. The machine is designed to operate with a flow pressure of between 100 kPa and 1,000 kPa. If it is higher than 1,000 kPa it is essential to fit a pressure reducing valve. Connection to the mains water supply should incorporate a mains stopcock with 3/4" thread. The stopcock should be fitted by a qualified plumber. In order to protect the water inlet valve, the two dirt filters - one in the open end of the inlet hose, one at the inlet point in the machine must not be removed. Extension hose Longer hoses 2.5 or 4.0 m in length are available from your Miele dealer or the Miele Spare Parts Department as optional extras.
,The connection point is subject to mains water pressure. Turn on the stopcock slowly and check for leaks. Correct the position of the washer and union if appropriate.
The washing machine is not suitable for connection to a hot water supply and connection to a household water softener is not recommended. Maintenance and care Only use a genuine Miele hose should you ever need a replacement or extension. These are tested to withstand pressure of at least 7,000 kPa.
Connection to the drainage system
The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull. If required, the drain hose can be extended to a length of 5 m. The necessary parts can purchased from the Miele Spare Parts Department or your Miele dealer. * For a delivery head of more than 1 m (up to a max. of 1.8 m) a replacement drain pump will need to be fitted. Please contact the Miele Spare Parts Department or your Miele Dealer. Drain hose connection: 1. Direct into a sink or basin: Please note the following: Hook the hose over the edge and secure. Make sure that the water can drain away freely without hindrance. Otherwise there is a risk of water overflowing or of some of the drained water being sucked back into the machine. 2. Connected securely to a plastic drain pipe with a rubber nipple. There is no need to use a non-return valve. 3. Connected securely to a standpipe. 4. Connected securely to a floor gully.
a Adapter b Nut c Hose clip d End of the hose ^ Fit adapter a to the sink drain outlet using nut b. ^ Attach the end of the hose d to adapter a. ^ Use a screwdriver to tighten hose clip c up close to the nut.
Electrical connection U.K.
All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out. The appliance is supplied with a mains cable with moulded plug ready for connection to a 230-240V mains supply. Please ensure the connection data quoted on the data plate match the household mains supply. Connection should be made via a suitable switched socket which is easily accessible after installation. For extra safety it is advisable to install a suitable residual current device (RCD). Contact a qualified electrician for advice. Do not connect via an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating). Non-rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words on the base of the plug (as applicable to the design of plug fitted). Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier.
The washing machine will store the most recently selected settings (programme, temperature, spin speed and any extra options) in memory once the programme has started. These settings will appear in the display the next time the machine is switched on. The machine is delivered with the memory function deactivated.
Anti-crease helps prevent creasing if laundry is not normally removed immediately after the end of a programme. The drum will turn at intervals for up to 30 minutes after the programme has finished. The door can be opened and laundry removed at any time during the anti-crease phase. On (the machine is delivered with this option selected) Anti-crease is activated. Off Anti-crease is deactivated.
Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed. And now Miele have developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry. The Miele CareCollection detergents and conditioning products are listed below. You can order these and many other useful products via the internet at:
Miele specialist detergents "Outdoor wear" This specialist detergent will clean your water-repellent outerwear with care. "Sportswear" The Miele Sportswear detergent is designed to clean sportswear whilst taking care of the special microfibres used in these garments. It will help to neutralise and remove odours whilst protecting the colour of the fabric and preventing static build-up. "Down Items"
All the products can also be ordered via the Miele Customer Contact Centre (see back cover for contact details).
This special-purpose detergent contains a mild tenside and has been specially formulated to keep down-filled items supple and to give them bounce. Miele proofing agent This special finishing agent reproofs garments against wind and water and provides a dirt-repellent finish whilst retaining elasticity and breathability.
"UltraWhite" detergent This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. "UltraColor" detergent for coloured garments This liquid detergent is particularly suitable for cleaning coloured and dark garments. The special formulation offers effective stain removal, even at low temperatures, while helping to prevent colours fading. Liquid detergent "For Delicates" This liquid detergent is ideal for the gentle treatment of delicate fabrics, such as wool and silk. Its special formulation cleans effectively at temperatures as low as 20C, while protecting the colour of your delicate garments. Fabric conditioner The Miele fabric conditioner will give your laundry a fresh, natural fragrance. It makes garments soft to handle and prevents static build-up during tumble drying.
Adventio KX-TG1312CX Lowrance X-25 PTS-307 Impression 5 S1000 Supreme CCD-TR2200E MX-412D UE22C4000PW Desktop S520 LA40B530 Explorist XL VGN-NR38m S G 640 LSC26905TT USR9003 Clavier 636 VGN-AR51J 32PFL3403D Motorola I455 NV-GS57GC Romeo 159 Motorola I335 340S2 SPH-B6600 Coolpix S9 DI-604 ZRB640W Autoloader GTP-760 CDJ-02 Wmls11B BHS-316 LH-T9654MB UX-7000R 5014046 T32341RO H25C39Y Expedition-1998 Switch Fantom G8 540 FGZ Hasselblad CFV DV 2000 GZ-MG67E CAR 300 F1 8G Vision 6109 M-DK ADC67555W MX200 SP-J720K DV-SP800 DRC8310N CQ-DP151W TI612BT1 Iiixe Legend Philips 109S 500ELX Dorsoduro 750 P-2304R-p1 Photosmart 475 AE2790 HK770 FR-1438-2 X1130P Flash Logicom L900 P2160 MCB395 Colibri T12 Vivicam 4000 TH-50PHD5 Vectis GX4 C250P Bissell 7901 P14007 Subito DC-223 EM 201 USA 1310 DSC-S730 - 2000 KX-F580 Center LVR-850 Telephone MX-26X3 Prestige P-78 386400 AX-450 DPM-07065A Vrbt200V Bonneville 1999 YO-P20HII Nuvi 1390 Review Disney QW-2738
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101