Table linen 60C to 30C

Curtains 104C to cold
Tip Detergent Load size Items Tip Detergent Load size

Pillows 95C to 40C

Outerwear 40C to cold Items Tip Detergent Load size Items Tip Outdoor clothing made from micro fibers. Close all zippers. Do not use fabric softener Detergent for delicates 3.5 kg To treat micro fiber, ski clothing, fine dense cotton (popelin) or table cloths to make them water repellent and soil resistant. The item should be washed and rinsed or dried. To get an optimum result dry the items in a clothes dryer or iron them. Only use water repellent with the hint "Suitable for membrane textiles". They are based on fluorochemicals. Do not use agents containing paraffin. Place the liquid detergent insert in compartment j an fill with water repellent. 3.5 kg

Proofing 104F to 86F

Water repellent

Load size

Disinfection programs Items Note Bed linen made of cottons or mixed fabrics. For different requirements with a temperature selection of 85C (thermal) to 40C (chemothermal) with the respective holding times. Use a detergent for disinfection and chemothermal disinfection. Regard the temperature level recommended on the packaging. 6.5 kg
Detergent Load size Hygiene
If a temperature lower than 55C was selected for the last wash program or if the program "Spin" was selected, "Hygiene" is displayed. When selecting a Hygiene program do not put any laundry into the drum, add a small amount of detergent in compartment j and start the program, or select a wash program with a temperature of 60C or higher. If the "Hygiene" display is disregarded, each program will run accordingly. Sluice 75C or Sluice 65C Items Note Detergent Load size Heavily soiled items of cottons, linen or mixed fabrics. To remove heavy soiling the laundry will be pre-rinsed twice. Universal detergent 6.5 kg

Program sequence

Main wash Water level Cottons Hygiene Cottons Uni. Minimum iron Delicates Sturdy Woollens Silk Dress Shirts Denim Disinfection* Kitchen linen* Table linen* Curtains * Pillows * Outerwear* Proofing* Towelling Sluice * Spin

4) 1) 2)

Rinse Water level ( ( ( e ( ( e ( ( ( ( ( ( ( e ( ( ( Rinses
Spin Rins spin L L L L L L L L L
Wash rhythm a a a b a c d a a a a a a a b a a
Final spin L L L L L L L L L L L L L L L L L L L
d d d e d ( e ( ( ( ( ( ( ( ( ( (

L L L

d = low water level ( = middle water level e = high water level
a = normal wash rhythm b = Gentle wash cycle c = Woolens d = Silk

After the program start the spin speed can be selected until the final spin starts. The Extras "Starch Stop" and "Rinse Stop" can be selected or deselected. The temperature and the Extra "Intensive" can be selected or deselected up to 5 minutes after the program start.
Adding/removing laundry during a wash program
You can interrupt the following programs to add or remove a piece of laundry. ^ Use the a button to open the door. ^ Add or remove the piece of laundry. ^ Close the drum door. The program will continue automatically.

Detergent

Only use laundry detergent formulated for front loading washing machines. For wool and wool blend fabrics use a detergent formulated for wools. Follow instructions on the detergent packaging for the correct use and amount of detergent. The amount of detergent used depends on the level of soiling: Light soiling No soiling or stains are visible. Normal soiling Some visible soiling or a few light stains. Heavy soiling Very visible soiling or stains. The size of the load and the water hardness level in your area have an impact on the amount of detergent necessary to obtain optimum wash results. If you do not know the water hardness level in your area, contact your local water authority.

Water hardness

Hardness level I II III Water quality soft moderate hard to very hard Water hardness in mmol/l 0 - 1.3 1.3 - 2.5 over 2.5 German hardness in d 0-- 14 over 14

Water softener

If the water hardness level is between II and III, you can soften the water to reduce detergent consumption. The detergent packaging should indicate the correct amount to use in your machine. Add the detergent, then add the water softener. From then on you can then use the recommended amount of detergent for water hardness level I.
Fabric softener, liquid starch
Fabric softener added to the wash program will make fabrics feel softer and will reduce static cling in the dryer. Liquid starch is a synthetic starch wash used to give fabrics some stiffness. Starch can be included in any wash program as part of the final rinse. Automatic dispensing of fabric softener or liquid starch ^ Add the fabric softener or liquid starch to compartment. Do not exceed the Max. level mark. Separate starch ^ Dispense the amount of starch recommended on the packaging. ^ Select the Extra "Starch" before starting a program. The program and the remaining time will stop. The display shows "Starch". ^ Dispense the starch directly in the drum. ^ Select a spin speed and confirm or press the "Start" button.
Dye removers / Fabric dyes
Do not use dye removers in this washer. ^ When dying fabrics in the washer, adhere to the manufacturers instructions. External dispensing The washer is set up for connection to an external detergent dosage system. A conversion kit is necessary which can be purchased from Miele.

The softener or liquid starch is automatically dispensed in the final rinse. At the end of the program a small amount of water remains in the fabric softener compartment. If starching frequently, clean the dispenser compartment and especially the siphon tube and conditioner channel. See "Cleaning the detergent drawer".
Cleaning and Care ,Before cleaning the appliance, disconnect the power supply by unplugging the unit or manually tripping the circuit breaker. ,Do not use chemical solvents, abrasive cleaners, glass or all purpose cleaners. These can damage plastic surfaces and other parts.

Cleaning the washer

^ Clean the exterior of the washer with a mild solution of non-abrasive detergent or soap and water. Wipe dry with a soft cloth. ^ Clean the drum with a stainless steel cleaner specially formulated for use in a washing machine. Cleaning the detergent drawer Detergent residue should be cleaned out regularly. ^ Pull out the detergent drawer as far as it will go. Press down on the red release lever and pull the drawer out of the machine.
^ Clean the detergent drawer with warm water. ^ Clean the siphon tube. 1. Remove the siphon tube from the compartment and rinse under warm water. Clean the pipe on which the siphon tube is attached. 2. Replace the siphon tube.

Cleaning and Care

Cleaning the inlet hose filter
The washer has two water inlet filters to protect each inlet valve. Check and clean these filters every 6 months. This may have to be done more frequently with some water supplies. Cleaning the inlet hose filters ^ Turn off the water faucet. ^ Unscrew the inlet hose from the valve by turning the connector counterclockwise using a wrench if necessary. Slowly turn on the faucet and check for leaks. If water leaks, tighten the bolt. Cleaning the filter in the inlet valve ^ Using pliers carefully loosen and remove the plastic hose connector from the inlet valve.
^ Using needle nose pliers, remove the plastic filter by pulling on the bar (see illustration). Rinse under running water and return. Replace the filter and seal then reconnect the hose. ^ Remove the rubber seal, 1, from the connector. ^ Using needle nose pliers, grasp the plastic filter, 2, and pull it out of the hose connector. ^ Clean the filter under running water and carefully remove any large particles. ^ Replace the filter and seal and reconnect the hose. Both filters must be put back in place after cleaning.

Frequently asked questions ,Repairs to electrical appliances must only be carried out by a qualified and trained person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held responsible for unauthorized work.
The following section will help you avoid placing a service call by identifying issues you may encounter while operating the machine:
A wash program cannot be started
Issue Possible fault Solution Possible fault the washer is connected to the electrical supply, the circuit breaker has not tripped. Follow the instructions as described in the "Before using for the first time" chapter. The display remains off. The washer has no power.
Upon selecting the The instructions in "Before using for the program "Spin" the program does not start. first time" were not followed. The display shows a foreign language.
Regard the display As long as an error message is messages. displayed, a program Confirm by pressing the jog cannot be started. shuttle. Press any direct select button. The Standby function will be ended.
The display is dark and The machine goes the "Start" light flashes into "Standby". The slowly. display shuts off to save energy.
Frequently asked questions
General problems with the washer
Issue The washer shakes during the spin cycle. Possible cause The four feet are not resting evenly on the floor. Solution Level the machine (see "Installation Instructions-Leveling the washer").
There are unusual sounds coming from the drain pump. Large residues of detergent remain in the dispenser drawer
There is no fault. Lapping sounds at the beginning and end of the pump process are normal. The water pressure is too Check and clean the low. filters in the water inlet hoses. Select the "Water plus" Extra if desired. Water softening Clean the detergent detergent additives tend drawer. In the future add to clump. the detergent first and then the water softener to the compartment.
The fabric softener is not completely dispensed or too much water remains in the compartment. The display shows a foreign language.
The siphon tube is either Clean the siphon tube, see incorrectly positioned or "Cleaning and careclogged. Cleaning the detergent dispenser drawer". A different language was Select the desired selected under language. The flag symbol "Settings-Language J". leads you to the setting.

Poor wash results

Issue The laundry does not get clean with liquid detergent. Possible cause Solution Liquid detergents do Use powder bleach. not contain bleaching Fill compartment j with agents. Fruit, coffee powder bleach and use a and tea stains may not dispenser ball for the be removed. liquid detergent. Never put liquid detergent and bleach together in the same wash compartment. Not enough detergent was used to dissolve greasy deposits in heavily soiled laundry. The laundry was soiled with grease (oils, lotions). Add more detergent to laundry with grease stains or use a liquid detergent. Run a 140F program with liquid detergent to clean the washer before using it for laundry again.

Laundry has a gray sticky residue.
There is white detergent The detergent was not After drying, remove white residues with a residue on dark laundry. completely dissolved clothes brush. because of hard water. These residues are In the future, use liquid difficult to remove. detergent. Items with greasy soiling are not clean after a wash program. Add a Pre-wash to the program. Use liquid detergent for the pre-wash. Use a powder detergent for the main wash. Use detergent which is specially formulated for heavily soiled work clothes. Contact the detergent manufacturer for more information.
The door will not open when the "Door" button is pressed
Issue Solution The washer has no power. Insert the plug into the outlet and the circuit breaker. Power failure To open the drum door, see "Frequently asked questions - Opening the drum door during a power failure.". Push the drum door on the locked side. Then press the "Door" button. Clean the drain filter and the drain pump as described in "Frequently asked questions Opening the drum door during a power failure.".
The door was not properly closed. There is still water in the drum and the washer cannot drain it away.
As a safeguard against scalding, the drum door cannot be opened if the wash water temperature is over 55C.
Opening the door during a power failure or when the drain is blocked
Machines with a drain pump If the main drain hose is clogged, water will be retained in the machine (max. 6.5 gal [30 l]).
,Disconnect the machine from the power supply.
^ Open the detergent dispenser drawer.
,Caution: If laundry has been
washed at a high temperature, the water draining out of the machine will still be hot! Stop and allow it to cool before proceeding.
^ Place a 2 quart capacity container under the drain tube.

^ Remove the tool.

^ Turn the lint trap lid counterclockwise. Do not remove it. About 2 quarts of water will drain out of the hose. If additional water remains in the machine, tighten the lint trap lid and empty the container. Repeat as necessary.
^ Open the lint trap door.
Once the flow of water stops: If the drain filter is not tightened securely water will leak out when the machine is used. Open the drum door
,Always make sure the drum is
stationary before reaching into the drum to remove laundry. A moving drum is extremely dangerous.
^ Remove the lint trap lid. ^ Remove any foreign objects or lint from the filter.
^ Insert a screwdriver into the notch, next to the lint trap, pull it down. The door will now open.
^ Check that the impeller (in the back of the chamber) rotates freely by spinning it with your hand. ^ Return the lint trap lid and tighten into place.
Machines with a drain valve Open the drum door
^ Press the lever for the emergency drain down and hold until you hear no more water running out.

^ Insert a screwdriver into the notch, next to the lever, pull it down. The door will now open.

Changing the light bulb

A burnt out light bulb will not affect the performance of the washer. ^ Disconnect the power supply to the work area by unplugging the unit, tripping the circuit breaker or removing the fuse. ^ Open the detergent dispenser drawer. Remove the tool from the rear side of the panel. ^ Open the drum door.
^ Press together the hooks of the plastic fitting, 2, to separate it from the bulb,1. ^ Replace the bad light bulb with a new one. A replacement bulb can be obtained by contacting Miele. The light bulb must not exceed the maximum wattage listed on the data plate. ^ Insert the light bulb into the plastic fitting. ^ Insert the drum lighting in the socket and turn clockwise.
^ Insert the tool into the slit of the light bulb, turn counterclockwise until resistance is felt. ^ Pull out the drum lighting.
To use the washer it is absolutely necessary to have the light bulb properly installed.

After sales service

Repairs In the event of a fault which you cannot fix yourself, please contact the Miele Technical Service Department. l 565-6435 service@miele.ca PC Update The indicator marked PC allows a technician to make use of new technology if new programs are developed or new fabrics are introduced. Optional accessories Optional accessories are available at your Miele dealer or Miele.
When contacting the Technical Service Department, please quote the model and serial number of your appliance. Both can be found on the data plate visible above the front glass on the inside of the door.
Installation Instructions

Installation

Front view
a Water intake hose cold b Water intake hose hot c Electrical connection d Control panel e Detergent dispenser drawer f Drum door
g Access panel to drain filter, drain pump and emergency door release h Height adjustable feet i Stand j Retaining clips (for concrete stand) k Recessed grip

Rear view

a Lid with transport grips b Mounting for: Water intake hose Drain hose Withdrawn shipping struts c Power cord
d Shipping struts with rotary protectors e Water intake hose (cold) f Water intake hose (hot) g Drain hose for drain pump h Drain hose for drain valve i Height adjustable feet

Washer/ Dryer Stack

Height: Stacking kit with pull out shelf 66 15/16" (170 cm) The Miele washing machine can be installed as part of a washer-dryer stack in combination with a Miele tumble dryer. An appropriate stacking kit* is required. Installation of the stacking kit must be provided by a Miele Service Technician. Reinstallation of the machine lid When reinstalling the appliance lid, check the firm fit of the cover at the rear bracket for a safe transport of the dryer.

Installation on a base

The machine can be installed on a steel base open or closed, or be installed on a concrete base. ^ Secure the two front feet of the washer with the supplied retaining clips when installing on a concrete base. ^ Read the supplied Installation manual.

Coin mechanism

The dryer can be equipped with a coin mechanism*. The reprogramming necessary for the coin mechanism must be done by a Miele Service Technician. Empty the coin mechanism regularly. Coins or tokens may get jammed.
Do not install devices to automatically turn the washer off, i.e. a clock timer.
* Available from your Miele dealer or Miele.

Installation site

The washer cannot be built-in.
^ Use the front washer feet and the rear excess end to transport the washer from its shipping pallet to the installation site. Do not lift the washer by the drum door.
,Do not install the machine directly next to or over an open floor drain or drain channel. Moisture can penetrate the machine and damage electrical parts.
A concrete floor is the most suitable surface for the washer. Concrete floors are less prone to vibration during the spin cycle than wooden floors.
,Ensure that the machines feet
and the floor are dry to prevent slippage during the spin cycle.
Removing the shipping struts
^ Remove the left and right rotary protectors.
,If the machine is installed on a masonry or concrete base it must be secured with retaining clips to prevent the washer from vibrating off the stand during the spin cycle.
^ The machine must be leveled and securely positioned. ^ To avoid vibration while spinning, the machine should not be installed on soft floor coverings. In case the installation must be on a wooden joist floor: ^ Install the unit on a 27 9/16" x 23 5/8" x 1 3/16" (70 x 60 x 3 cm) plywood base. Ideally the base should be large enough to span several joists and should be anchored to the joists and not just the floor boards. It is best to install the washer in the corner of a room, where the stability of the floor is at its greatest.
1. Unhook the rotary protector with a screw driver. 2. Remove the rotary protectors.
^ Turn the left shipping strut counterclockwise 90 with the enclosed combination wrench.
^ Turn the right shipping strut counterclockwise 90 with the enclosed combination wrench.
^ Pull the shipping strut out.
^ Pull out the shipping strut out.

Installation ,Movement of the washer without
the shipping struts in place should be kept to a minimum. The shipping struts should be stored on the back of the washer for future use. They must be reinstalled before moving the machine.
Installing the shipping struts
^ Reinstall the struts by reversing the installation procedure. ^ Close the holes with the rotary protectors and their caps.
^ Fasten the shipping struts at the rear side of the washer. Take care to insert the drill holes, b, into the clamps, a.

Leveling the washer

Adjust the four leveling feet The washer is leveled by adjusting the four feet. The machine is boxed with the feet completely screwed in.
To ensure smooth operation the washer must be level. Failure to level the machine can result in increased water and energy consumption as well as the washer "banging" during the spin cycle or "walking" across the floor during use. ^ Turn the locking ring, 2, counterclockwise with the enclosed combination wrench. Unscrew each of the four feet as much as necessary by turning both the foot, 1, and the locking ring, 2, to the left. ^ Check that the machine stands level. ^ Once level, hold the foot, 1, steady with a wrench. Turn the locking ring, 2, with the combination wrench towards the machine.
,All four locking rings must be
tight against the bottom of the machine. In addition, check to see that the feet were not inadvertently unscrewed while tightening the rings. Running a machine that is not level or whose feet are not tight may cause damage to both the machine and its surrounding area.

Water connection

Cold water connection A water faucet with 3/4" threat must be provided on-site. If none is available the machine must be connected to a water line by a qualified plumber. The water pressure must be within 14.5 -145 psi (1 -10 bar). If the water pressure is greater than 145 psi (10 bar), a pressure reducer must be installed. If the water pressure is below 15 psi (1 bar), there will not be enough water available for a complete fill. The cold water hose (blue mark) is not suitable for a hot water connection. ^ Connect the cold water intake hose (blue mark) to the cold water valve. ^ Turn on the valve(s) and check for leaks. The water intake hoses are equipped with screen filters. Do not remove these filters except for cleaning. Maintenance Replace the water hoses only with genuine Miele hoses. Extension hoses Extension hoses (8 2" or 13 [2.5 m or 4 m]) may be obtained from Miele.

,To convert the machine to another electrical connection, please read the converting manual on the wiring diagram inside of the washer. The conversion must be performed by a Miele Service Technician. Additionally the "Heating level" setting must be adjusted. ,Do not install devices to automatically turn the washer off, i.e. a clock timer.

Technical Data

Height Width Depth Depth with the door open Weight Maximum floor load Capacity Fuse rating Rated load Fuse rating Noise level during spinning (Noise emission 3. GSGV) Minimum water flow pressure Maximum water pressure Length of intake hose Length of power cord Drain height maximum (Drain pump) Light bulb for drum light 85 cm 59.5 cm 72 cm 112 cm 109 kg 2778 Newton (approx. 278 kg) 6.5 kg dry laundry see data plate see data plate see data plate < 70 dB(A) 14.5 psi (1 bar) 145 psi (10 bar) 1.6 m 1.6 m 1m Type G4 (5 Watts/12 Volt)
Help to protect the environment
Disposal of the packing materials
The cardboard box and packing materials protect the appliance during shipping. To prevent suffocation of children ensure that any plastic wrapping, bags, etc. are disposed of safely and kept out of the reach of children. Please recycle.
Disposal of an old appliance
Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that the appliance presents no danger to children while being stored for disposal. Before discarding an old appliance, unplug it from the outlet, cut off its power cord and remove any doors to prevent hazards.
Menu Settings J to adjust standard settings
The washer electronic can be adjusted to changing demands with the settings. The settings can be changed at any time.

Settings J

Opening the menu Settings
^ Select the "Settings" J in the main menu and confirm by pressing the jog shuttle. Selecting Settings

Settings

BackA Language F Water plus Suds cooling H
^ Select the settings to be changed and confirm. If no selection was made in the sub-menu, the display will switch back to the "Settings" menu after 20 seconds. Leaving the Settings menu ^ Press "Back" and confirm. The display shows the main menu.

Language J

The display contents can be shown in different languages. The displayed language can be set in the sub-menu "Language" J. ^ Select the desired language and confirm with "OK". The flag behind the word "Language" is a guide to find the settings menu in case a foreign language is shown. If the language setting was changed, it is only valid for the current wash program. Once the program ends, the display will show the language which is set under "Settings - Supervisor level".

Suds cooling

Cold water is added at the end of the main wash to cool the wash water. Suds cooling is carried out when a wash temperature of 70C or more is selected. Suds cooling should be activated when the drain hose is hung into a sink, to prevent scalding. Suds cooling is factory set turned on.

Water plus

In the setting "Water plus" you can select an extra setting from below. Water plus The water level increases (more water) in the wash and rinse cycles of the program (delivery status). Additional rinse An extra rinse cycle is added in the programs "Cottons Hygiene", "Cottons Uni." and "Minimum iron". Water+ and Add. rinse The water level is increased in the wash and rinse cycles and an extra rinse cycle is added to the programs "Cottons Hygiene", "Cottons Uni." and "Minimum iron".

Time of day

The selection allows the clock to be shown as 24 hours, 12 hours or not at all. The time of day is also set here. If the clock is not selected the delay start can only be shown only as a 24 hour clock timer. The display will how the timer counting down until the start of the program but not he current time of day. Selecting the clock ^ Select the clock display and confirm. The display changes to the time of day setting. Set the time of day ^ Select the current hour with the jog shuttle and confirm. Repeat with setting the minutes and confirm. Press again to save the time of day.

Contrast

The contrast of the display can be set in ten different levels. The machine is factory set to level 4. The contrast changes immediately when a different level is selected. ^ Confirm the setting with the jog shuttle.

Brightness

The brightness of the display can be set in ten different levels. The machine is factory set to level 5. The brightness changes immediately when a different level is selected. ^ Confirm the setting with the jog shuttle.

Standby

The display goes out after 10 minutes and the "Start" button flashes slowly to save energy. On The display will go into Standby mode: if no program was selected after the machine was turned on. after a program has started. at the end of a program. Not in current prog. (Factory default) The Standby function will be turned on if no program was selected after the machine was turned on. By turning the jog shuttle or pressing any button the display is turned on again.

Memory

The Memory function remembers the addition of an extra feature to a program, a change in spin speed or the temperature the next time that program is selected. Once the wash program is selected again the washer shows the saved options. The memory function is not active when favorites are selected with the direct select buttons. The Memory function is factory set "off".

Main wash water

The water type for the main wash can be selected (except for the programs "Woollens", "Silk" and "Curtains"). The hot water intake will be only accessible at a wash temperature of 30C or higher. The machine comes factory set with the water type "hot". If the washer is not connected to hot water, the program running times will be extended and vary from the displayed remaining times.

Pre-wash water

The water type for the pre-wash can be selected (except for the program "Curtains"). The hot water intake will be only accessible at a wash temperature of 86F (30C) or higher. The machine comes factory set with the water type "hot".
If "Industrial water" is used, the washer must be refitted accordingly.

Rinse water

The water type for the rinse in the programs "Cottons Hygiene", "Cottons Uni.", "Minimum iron", "Table linen", "Kitchen linen", "Towelling" and "Sluice" can be selected. The hot water intake will be only accessible at a wash temperature of 50C or higher. The machine comes factory set with the water type "hot". If "Industrial water" is used, the washer must be refitted accordingly.

Water level Cottons

The program "Cottons Hygiene" and "Cottons Uni." allows you to increase the water level for the main wash. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.)

Pre-wash duration

The wash time for the pre-wash can be extended. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.)
Wash time Cottons Water level Min. iron
The program "Minimum iron" allows to increase the water level for the main wash. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.) The programs "Cottons Hygiene" and "Cottons Uni." allow to increase the water level for the main wash. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.)
Min. iron Pre-wash temp. Cot.
The Pre-wash temperature for the programs "Cottons Hygiene" and "Cottons Uni." can be selected. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.) The program "Minimum iron" allows to extend the wash time for the main wash. The machine comes factory set with the option block parameter selected. (The water level will be controlled according to the factory set program data.)

The programs "Cottons Hygiene" and "Cottons Uni." allow you to change the number of rinse cycles. 2 rinses (factory default) 3 rinses 4 rinses 5 rinses The program "Minimum iron" allows a pre-rinse of the laundry. The machine comes factory set with this option "off".

Spin free of charge

When operated by a coin mechanism, the program "Spin" can be activated free of charge. The machine comes factory set with this option "off".

No. rinses min. iron

The program "Minimum iron" allows you to change the number of rinses. 2 rinses (factory default) 3 rinses 4 rinses

No detergent

If an external dispensing system is fitted to the machine it will not be accessed if "No soap" is selected. You have the option to show the Extra "No Soap" in the menu "Extras".
Leaving the Settings menu
^ Press "back" and confirm. The display shows the main menu.
The machine comes factory set with this option "off".

External dispenser

The washer is set up for connection to an external dispensing system. To use the external dispensing system the setting must be adjusted/set accordingly. The machine comes factory set with this option "off".
Alteration rights reserved / xx05

M.-Nr. 700 / 00 en - CDN

FEATUR ES Fa b r ic care

Miele Compact Laundry

Laundry Collection Since its first laundry machine was built in 1900, Miele has been helping customers care for their clothes professionally at home. Made in Germany, every innovation in our machines, like our patented honeycomb drum, is engineered not only to clean clothes better, but also to make clothes last longer
C onvenience Reliability Eff iciency
Microprocessor adjusts washing and drying conditions to best care for specific types of fabric, including cycle duration, temperature, and spin speed. Patented Honeycomb* drum reduces the size and number of water jet holes, virtually eliminating the possibility of snags, and maintaining a cushioning layer of water between the clothes and the drum. The honeycomb drum ensures similar gentleness in the dryer, too. High water temperature option allows for powerful cleaning results without the use of harsh chlorine bleach. To eliminate damage due to over-drying, while also saving energy, Miele dryers use moisture sensors rather than timers to stop the load once the load is dry. The drum in a Miele dryer also rotates in both directions. This functionality ensures even drying, and reduces wrinkling due to roll-ups. Accompanying Miele CareCollection line of detergents is tailored for any type of fabric, from delicate woolens to advanced sports performance materials.
Load sensors determine the size of load, adjusting water volume accordingly. This allows even small loads to be washed with limited energy and water. All Miele washers are EnergyStar rated.
Every Miele machine is designed and tested to last for 10,000 wash cycles, ensuring hassle-free operations for decades. Made in Germany.
by reducing fabric strain and wear. Even more, all Miele washers and dryers are tested to last the equivalent of twenty years. So treat your clothes to an unsurpassed level of professional care right in your home.
The 5.5 KG drum can accommodate a large variety of load sizes, from a queen-size comforter to a few delicates. Intuitive Touchtronic controls allow you to easily select the right program for all kinds of textiles. A memory function remembers the settings for each program. Internal sensors ensure that washing loads are balanced. A large door, angled drum and LED lighting make loading and unloading easy.

D esig n

An enameled front panel ensures that each washer and dryer will maintain their timeless appearance for years to come.
*W1612 has a microperforated drum.

W1000 Series

WASHERS W1612 5.5 KG /-

W3000 Series

W3033 5.5 KG -/ W3035 5.5 KG -/

Miele Compact Washers

Laundry Collection

Versati l i ty

CAPACITY SHORT / Extended OPTION Heavy Soil OPTION Sensitive OPTION 1000 W Heating Element NO Spin Maximum Spin Speed Maximum Temperature Number of Programs Normal Colours Darks Wrinkle-free Sanitize Handwash Woolens Silk Custom Extra White Delicates Denim/Jeans Dress Shirts Pillows Outware Table Linens Beach Towels Express Drain/Spin Quick Rinse Annual Energy Consumption Energy Star Qualified Child Safety Lock Drum light

1200 rpm 95C / 203F 10

1300 rpm 70C/158F 19

Perform ance

189 kWh

139 kWh

D esign
Bleach Dispenser Enameled Front Stainless Steel Drum Matching Pedestal Microperforated Honeycomb WTS410 Honeycomb

co ntr ols

Touchtronic Controls Large LCD screen Delay Start/ Countdown Timer Buzzer on/off Miele Price Miele ADVANTAGE Miele ADVANTAGE PLUS Miele PricePedestal $1,599 $1,809 $2,109 $2,499 $2,709 $3,009 $499 $2,999 $3,209 $3,509

T8003 T8005 T8013C

Miele Compact Dryers

DRYERS

T7644C
CAPACITY TURBO OPTION GENTLE OPTION Heating System Drying System Number of Programs

5.5 KG

5.5 KG.

electrical vented 10

electrical condensing 10

electrical vented 8

electrical condensing 8

Extra Dry

Normal Wrinkle Free Mixed Woolens Delicates Timed Warm Timed Cold
Annual Energy Consumption Drum light Large Lint Filter

T7634 (vented)

T8003 (vented)

431 kWh

424 kWh

Design

Glass Door Enameled Front Stainless Steel Drum Matching Pedestal* Stacking kit* Touchtronic Controls

smooth WTV414

honeycomb honeycomb honeycomb WTS410 WTV407 WTV419 WTS410 WTV407

T7644C (condensing)

T8005 (vented)

contr ols

Electronic Moisture Monitoring Buzzer on/off Anti-creasing Program Sequence Display Miele Price Miele ADVANTAGE Miele ADVANTAGE PLUS Miele PricE - PEDESTAL

$1,149 $1,359 $1,659

$1,449 $1,659 $1,959
$1,499 $1,709 $2,009 $499
$1,849 $2,059 $2,359 $499

$1,949 $2,159 $2,459

T8013C (condensing)

*optional

Miele UltraColor 2.5 kg
Highly concentrated detergent for coloured fabrics. Ensures long life and use of items made with dirt-repellent and moisture wicking properties, such as outerwear, sportswear and special tablecloths. miele.ca

Miele ForeverCare

With Miele ForeverCare, you get a guarantee. A guarantee that our commitment to you extends far beyond the time you buy, throughout the very long life of your machine. We are confident in offering you unparalleled customer service.
What is Miele ForeverCare?
Miele provides unique advantages to our customers with a combination of features unparalleled in the appliance category, namely:
Manufacturer-Direct Service. If you ever have a problem with your Miele machine, it's our own Miele Factory Service Technicians who take care of it. Most problems can be solved on the first visit, as we know the exact model you have and carry the genuine Miele parts you will need. Extended Warranty from the Manufacturer. We want you to enjoy a long and trouble-free experience with our machines. In addition to the standard warranty, we have Miele Extended Care Certificates. This direct offer from Miele allows you to increase your hassle free coverage up to ten years. The extended warranty relationship remains directly with Miele, so you can deal with us if you have any issues. Miele Custom Plans. The chart below illustrates how you can upgrade the benefits of ForeverCare.

Miele Advantage Plus

Manufacturer Delivery and Installation. We want your machine to work perfectly from the first time you use it. So we offer delivery and installation in your home ourselves, with our fully Miele-dedicated service team. Installation can be organized within 48 hours of ordering through the Miele Customer Care Centre, and your delivery is tracked with GPS so we can provide you with a nearly exact time of delivery. Miele CareCollection. To ensure you make the most of your Miele appliance, we've created a range of everyday and specialty products available for purchase. From laundry detergent, to dishwasher tablets, to a variety of cooking accessories, these products are designed specifically for your appliance, ensuring better results and a longer, hassle-free, lifespan.

Benefits One-on-one relationship with Miele Canada

Miele Pricing

Miele Advantage

Visit The Miele Gallery

Miele Galleries are open to the public to provide the complete Miele experience and are located in four cities across Canada: Montreal, Toronto, Calgary, and Vancouver.

TOLL FREE :

Instant Access to Miele Customer Care Centre Automatic Warranty Registration 1 Yr Manufacturers Warranty 5 Yr Total Extended Care Certificate (ECC) Included 10 Yr Total Extended Care Certificate (ECC) Included Miele Culinary Institute Events Miele Culinary Institute: MasterChef Class V.I.P Invitation to Miele Gallery Events Miele CareCollection Bonus Miele Email Concierge Service Miele Complete Appliance Check-up Miele Appliance Recycling Pick-up
10% off ECC 10% off ECC Priority Registration Complimentary Pass
Priority Registration Complimentary Pass Plus One

1.800.565.6435

EMAIL :

$25 Savings

$50 Value

customercare@miele.ca

HAVE QUESTIONS?
Please ask your Miele Chartered Agent for more information or go to
Terms and conditions apply to Miele Pricing, Miele Advantage and Miele Advantage Plus benefits. Miele reserves the right to change these benefits at anytime. For full terms and conditions, please visit www.miele.ca.