29. Rear control dial 30. Control panel door 31. AF button (28-29, 68) 32. Remote-control terminal (62) 33. Eye-start switch (21) 34. Rewind button (24) 35. Film window (16)
1.Grip sensor (20) 2. AF illuminator/Self-timer lamp (32, 117) 3. Front control dial 4. Shutter-release button 5. Data panel (6) 6. Program-reset button (9, 120) 7. Built-in flash (34-39) 8. Subject program button (41-47) 9. Memory-recall button (101) 10. Memory-number lever (100) 11. Exposure-mode button (50)
PC terminal (97) Strap eyelet (11) Flash-compensation button (91) Lens release (14-15) Back-cover release (16) Focus-mode button (31) Exposure-compensation button (74) 19. Mirror* 20. Lens contacts* 21. Depth-of-field preview button (114)

CONTROL PANEL

A B C D E F G H A. Data-memory button (108, 111) B. Self-timer/drive-mode button (77-83, 117, 118) C. AF-mode button (66) D. Flash-mode button (38, 89, 92-96) E. Metering-mode button (73) F. Enter button (100) G. ISO button (115) H. Adjust button (69, 77, 81, 104-105, 109-111)

* Do not touch. 4

Page 6

DATA PANEL

VIEWFINDER
Subject Program Selection icons Battery-condition indicator Film-speed mark Flash-mode indicators Shutter-speed/Filmspeed/Focus-area display 6. Aperture/Exposurecompensation/Flashcompensation display 7. Exposure-compensation indicator 8. Exposure-mode indicator 9. Flash-compensation display 10. Self-timer indicator

1. 2. 3. 4. 5.

11. Data-memory indicator 12. Frame counter 13. Film-transport signal 14. Film-cartridge mark 15. Exposure-bracketing indicator 16. Drive-mode indicator 17. Multiple-exposure indicator 18. AF-mode indicator 19. Focus-area indicator 20. Manual-focus indicator 21. Metering-mode indicator 22. High-speed sync indicator 23. Release-priority indicator
1. 2. 3. 4. 5. 6. 7. 8. 9.
Panorama frame Local-focus areas Horizontal wide-focus frame Vertical wide-focus frame Spot-metering area Flash-on indicator High-speed sync flash indicator Flash signals Wireless-flash indicator
10. Focus signals 11. Shutter-speed/Focus-area display 12. AEL indicator 13. Aperture/Exposurecompensation/Flashcompensation display 14. Metering index 15. Frame counter

Page 8

QUICK OPERATION

Insert the batteries.

The camera uses one 2CR5 cell.
Set the camera to full-auto operation.
Press the program-reset button.

Attach a lens.

Align the red marks, then turn it gently clockwise until it clicks.

Turn eye-start on.

Turn the camera on.
Set the main switch to ON.

Frame the picture.

Align your subject in the focus frame and the camera will automatically focus.

Load the film.

Line the film-tip with the red mark, then close the back cover.

Take the picture.

Gently press the shutter release button all the way down.

Page 10

STANDARD ACCESSORIES
NECKSTRAP Attach the neckstrap as shown.

EYEPIECE CUP

Attach the eyepiece cup as shown.
EYEPIECE AND ACCESSORY SHOE CAPS
An eyepiece cap is attached to the strap. Before using the self-timer or making long exposures, remove the the eyepiece cup and attach the cap to the viewfinder eyepiece to prevent stray light from entering the camera and affecting exposure. The camera also comes with an accessory-shoe cap which protects the accessory-shoe contacts. When using a flash or other accessory, slide the accessory-shoe cap into the eyepiece cap for safekeeping. 10 11

Page 12

INSTALLING THE BATTERIES
Your camera uses one 6-volt 2CR5 battery to supply power for all camera operations. Please read all warnings in the For Proper and Safe Use section of this manual, as well as warnings supplied by the battery manufacturer.
BATTERY CONDITION INDICATORS
A battery-condition indicator will appear in the data panel for 5 seconds each time the camera is turned on. This mark signifies the power status of the battery. Full-battery symbol: Power is sufficient for all camera operations.
Set the main switch to LOCK. Slide the battery-cover release in the direction indicated to open the cover.
Insert the battery according to the marks on the inside of the chamber cover. Snap the cover closed.
Low-battery symbol: Power is low, but all functions are operational. Keep a fresh battery ready.
Blinking low-battery symbol: Power is extremely low. The battery will need to be replaced very soon.
Blinking low-battery symbol only: Power is too low for normal camera operations. Replace the battery.
This indicator will appear even while the main switch is set to LOCK.
No display: Power is too low for any camera operations. Replace the battery or check that it is inserted correctly. 12 13

Page 14

ATTACHING AND REMOVING THE LENS
ATTACHING THE LENS Remove the camera body cap and the rear lens cap as shown. REMOVING THE LENS While pressing the lens release, turn the lens counterclockwise until it stops. Gently remove the lens from the mount. Attach the body cap or another lens to the camera and replace the rear lens cap.

This will protect the camera interior, lens contacts, and lens elements.
Align the red bead on the lens with the red dot on the camera's lens mount. Gently insert the lens into the mount and turn it clockwise until it clicks into the locked position.
Do not press the lens-release button while attaching the lens. The lens will turn past its mark and will not work.
Do not force the lens onto the body if it does not turn smoothly. Do not touch the inside of the camera, especially the lens contacts and mirror. Touching or lifting the mirror may impair the mirror's alignment or scratch it. Dust on the mirror will not affect meter readings or picture quality. If it is distracting, have the camera cleaned at an authorized Minolta Service Facility. Remove dust, dirt, and moisture from the lens mount before attaching or removing the lens. The use of a lens hood is recommended to reduce flare and ensure maximum image quality when the flash will not be used.

17/10/97 10:52 AM

Page 16

LOADING FILM

Remove and discard the protective cover in the film gate before loading film for the first time. Check the film window before loading film. If a film cartridge is loaded, do not open the back cover. See page 24 for instructions on rewinding a partially exposed roll of film.

Protective Cover

Close the back cover and slide the main switch to ON.
The camera will automatically advance the film to the first frame and 1 will appear in the frame counter in the data panel. If DX-coded film is used, the camera will automatically set the correct film speed and display it in the data panel for 5 seconds after loading. will blink in the frame counter and the shutter will remain locked if the film is loaded incorrectly. Open the back cover and repeat steps 2 through 4.
Slide the back-cover release down to pop open the back cover.
Place the film cartridge in the film chamber as shown.
Never touch the shutter curtain with your fingers or with the film tip. Its precision design makes it extremely sensitive to pressure.
Extend the leader between the guide rails to the film-leader index.
If the film tip extends beyond the red mark, gently push the excess film back in the cartridge.
Always load film in subdued or shaded light to reduce the chances of fogging the film. Do not use Polaroid instant 35mm film. Winding problems may occur. Non DX-coded film: If non-DX-coded film is used, the ISO setting of the previous roll of film will be used. The camera assumes the number of frames is no more than 36. If a roll of non-DX-coded film with more than 36 exposures is loaded, please change the Film Rewind Start customized setting to manual start (p 102).

Page 18

HANDLING THE CAMERA

HOLDING THE CAMERA

Press and hold the subjectprogram button.
Turn either control dial until appears alone in the data panel. Release the subject-program button.
Tips: Use a lens in the mid-telephoto range. Use flash when your subject is backlit or there are strong shadows across the face.
Tips: Use a wide angle lens to create a feeling of depth in the photograph. Use flash when a subject in the foreground is backlit or has strong shadows across the face. If there is no subject in the foreground, do not use flash. Use a tripod, especially at slower shutter speeds.

Page 44

CLOSE-UP MODE
Use Close-up mode when photographing objects from short distances. Close-up photography requires accurate focusing; use focus hold or manual focus to ensure sharp focus. The camera will select the best possible aperture and shutter speed for your subject.

SPORTS MODE

Select Sports mode when faster shutter speeds are needed to stop action. In Sports mode, the camera sets the fastest possible shutter speed and continually adjusts the focus to track fast-moving subjects.
Tips: For best results, use an AF macro lens. Do not use the built-in flash when your subject is closer than 1 meter. Use a tripod to reduce camera shake. Be aware of the minimum focus distance of the lens.
Tips: Use fast film and keep the focus frame on your subject. Mount the camera on a tripod when using a telephoto lens. Flash is only helpful if the subject is within the flash range.

Page 46

NIGHT PORTRAIT MODE
Use Night portrait mode for taking portraits with scenic backgrounds at night. Night portraits require a balanced exposure between the camera's flash and the ambient light. In this mode, the camera sets the largest possible aperture and a slower shutter speed to allow the ambient light in the background appear in the photograph.
PHOTOGRAPHING NIGHT SCENES
When photographing scenery at night, set the camera to Night Portrait mode and do not use the flash. Longer shutter speeds are set in this mode, so you can easily capture beautiful photographs of twilight scenery and night skylines.
Raise the built-in flash. Press and hold the subjectprogram button.
Tips: Warn your subject not to move while the picture is taken. Use faster film and a tripod. Set the flash to when using night portrait mode.
Tips: Use faster film and a tripod. When photographing dark night scenes, it may be difficult for the camera to focus. Use manual focus or focus lock.

Page 48

EXPOSURE MODES
The 800si has four exposure modes. P - (PROGRAM) -Programmed Autoexposure Mode P mode (PROGRAM) is ideal when you want to give your full attention to the subject and give the camera control over exposure. A - Aperture Priority Mode In A mode, you select the aperture and the camera automatically sets the shutter speed required for proper exposure. Use this mode when you want to control depth of field.

EXPOSURE BASICS

S - Shutter Speed Priority Mode You select the shutter speed in S mode and the camera automatically sets the aperture for the best exposure. Use S mode to have full control over shutter speed settings. M - Manual Mode In M mode, you have full control of exposure and the camera's meter index will show you how your settings relate to the TTL meter.
MEMORY: The Exposure Mode setting can be stored in memory. See page 99 for information.

Page 50

CHANGING THE EXPOSURE MODE Press and hold the exposuremode button. Turn either control dial until the mark for the desired mode appears in the data panel. Release the exposure-mode button.
P - PROGRAM EXPOSURE MODE
P mode (PROGRAM) is ideal when you want to give your full attention to the subject and give the camera control over exposure. When focused on your main subject, Expert Program Selection automatically analyzes subject size, motion, and magnification as well as lens focal length. Then, it sets the shutter speed and aperture according to the scene requirements.
While pressing the exposure-mode button, turn either control dial until P appears in the data panel. Release the exposure-mode button to enter the selection. Compose your scene and take the picture.

SHUTTER SPEED

In the data panel and viewfinder, fraction of a second shutter speeds are indicated by whole numbers (from 2 to 8000). For example, if 250 appears, the shutter speed is 1/250 of a second. Shutter speeds in seconds are represented by " after the number. For example 3" is a 3 second exposure (0"7 is 7/10 of a second).
Using the exposure-mode button to set P mode will not change any other camera settings. To return all camera settings to default, press the program-reset button.
PA AND PS: CREATIVE EXPOSURE CONTROL
After the AE system has been activated, you can change the shutter speed or aperture, automatically set by Expert Program Selection, in 1/2-stop increments while maintaining a correct exposure. PA - Turn the rear control dial until the desired aperture setting appears in the viewfinder and body data panels. PA appears in the body data panel.
The aperture will not change, even if lighting conditions change. The shutter-speed value will be set automatically. Continued on next page.

17/10/97 10:55 AM

Page 52
PS - Turn the front dial until the desired shutter speed setting appears in the viewfinder and body data panels. PS appears in the body data panel.
The shutter-speed will not change, even if lighting conditions change. The aperture value will be set automatically. In PA mode, if the shutter speed blinks, turn the rear control dial until the blinking stops. If the aperture blinks in PS mode, turn the front control dial until the blinking stops. The built-in flash or an attached accessory flash cannot be used in PA and PS mode. If the built-in flash is up or an accessory flash is attached to the camera and the flash-on indicator appears in the viewfinder, PA and PS mode cannot be selected.

In general, wider lenses provide more depth-of-field and longer (telephoto) provide less depth of field. There is less depth of field when your subject is close to the lens.

Page 56

S - SHUTTER PRIORITY MODE
In S mode, you select the shutter speed and the camera automatically sets the aperture required for proper exposure. This mode is useful when you want to control the motion in the photograph.

S-MODE FLASH

While pressing the exposuremode button, turn either control dial until S appears in the data panel. Release the exposure-mode button to enter the selection. Compose your scene and turn either control dial to select the desired shutter speed.
The shutter speed display will change in 1/2-stop increments with each click of the dial. If the aperture display blinks, a correct exposure is not possible with the shutter speed you have selected. Turn either control dial until the blinking stops to select another shutter speed.
When the flash is ready, will appear in the viewfinder. Choose a shutter speed of 1/200 or slower, as this is the sync speed. The aperture is set automatically. A larger f-number will result in a smaller flash range. Push the flash down if it is not needed. If the aperture blinks in the data panel and viewfinder, the aperture required for proper exposure is beyond the lens' range. Turn the dial to select another shutter-speed until the aperture stops blinking.

Page 58

SHUTTER CONTROL

M - MANUAL MODE

In M mode, you have full control of exposure and the camera's meter index will show you how your settings relate to the TTL meter.
While pressing the exposuremode button, turn either control dial until M appears in the data panel.
Fast Shutter Speed Slow Shutter Speed
Because the shutter speed controls the duration of exposures, it also determines how moving subjects will appear in the final image. Use a slow shutter speed to blur the motion of your subject. Use a fast shutter speed to stop the motion of your subject. In addition to stopping action, fast shutter speeds can help prevent blur caused by camera movement during the exposure.

This camera has three autofocus modes that can be changed at any time. MEMORY: The Focus Mode setting can be stored in memory. See page 99 for information.

SINGLE-SHOT AUTOFOCUS

When the shutter-release button is pressed partway down, the camera focuses until sharp focus is confirmed and then focus is locked. Focus will remain locked while the shutter-release button is pressed partway down or until after the shutter-release button is pressed all the way down. Use Single-shot Autofocus when photographing non-moving subjects or subjects that are outside the focus area. See Focus Lock, page 27.

AUTOMATIC AUTOFOCUS MODE

When autofocus is activated by pressing the shutter-release button partway down, the camera will continue focusing while the subject is moving and lock focus when it is still. Automatic Autofocus Mode works well in any situation, but is especially useful for subjects that move and stop suddenly.

CONTINUOUS AUTOFOCUS

The camera continues focusing while the shutter-release button is pressed partway down. The shutterrelease button can be pressed all the way down when the subject is in focus. Continuous Autofocus should be used at sporting events or other occasions when the subject moves continuously.

Page 66

CHANGING THE AUTOFOCUS MODE Press the AF-mode button in the control panel.

FOCUS FRAME

Your camera has a wide focus area and four local focus areas. A wide focus area is ideal for catching subjects in motion and snapshots. A local focus area allows for precise control over the location of focus.
Turn either control dial to set the AF mode to , , or.
Make sure the camera is in autofocus mode. If M. FOCUS appears in the data panel, press the focus-mode button to select autofocus. The selected AF mode will remain when a Subject Program Selection is made. The AF Illuminator will not operate when mode is selected.

Horizontal (Wide)

Vertical

Horizontal (Local)

WIDE FOCUS AREA
The camera uses all of the AF sensors to focus. It determines which sensor is focusing on the main subject. Wide Focus Area provides flexibility in framing and makes it easier for the camera to focus on moving subjects. The default setting of the camera is wide focus area.

Page 68

LOCAL FOCUS AREA
Select a specific local focus AF sensor for the camera to use.

RELEASE PRIORITY

The default setting of the 800si is autofocus-priority shutter release. When the camera is in autofocus, the shutter will not release if the subject is not in focus. You can set the camera to shutter-release priority so the shutter will release even if the subject is not sharply focused.
While pressing the AF button, turn the front control dial to display each local focus area.
Press and hold the adjust button and press the ISO button.

SELECTING A METERING METHOD Press the metering-mode button in the control panel.
Turn either control dial until the icon of the desired method appears in the data panel. Press the shutter-release button partway down to enter the setting.

SPOT METERING

Spot metering uses only the center segment of the honeycomb pattern. The spot-metering circle appears in the viewfinder to indicate the metering area.
MEMORY: The Metering Mode setting can be stored in memory. See page 99 for information.

17/10/97 10:57 AM

Page 74

EXPOSURE COMPENSATION

This function enables you to bias the camera's exposure calculation up to 3 EVs over or under the normal metered setting.

AE LOCK

Use this function to lock the automatic exposure settings without locking the autofocus.
While pressing the exposure compensation button, turn either control dial.
Center the subject of which the meter-reading will be made.
When the desired compensation value appears in the viewfinder and data panel, release the exposure compensation button.
The compensation value will disappear from the body data panel, but will remain in the data panel. Press the exposure-compensation button at any time to make the exposure factor appear in the data panel. In P, A, and S modes and each subject program mode, the metering index will appear in the viewfinder when the autofocus is activated by Eye-start or pressing the shutter-release button partway down. Cancel exposure compensation using the above procedure to set the compensation value to 0.0.
Press and hold the AE Lock button.
AEL appears in the viewfinder and the data panel. The spot-metering frame appears in the viewfinder. The 0 mark in the meter index represents the AE lock exposure. The selected metering method does not change.
MEMORY: The Exposure Compensation setting can be stored in memory. See page 99 for information.

Page 76

While holding the AE-lock button, recompose the picture.
A mark on the meter index will indicate the difference between the locked exposure (0) and the exposure value of the area currently being read. Do not release the AE lock button until after the picture is taken.

EXPOSURE BRACKETING

Exposure bracketing lets you expose a series of frames with exposures below and above the normal metered exposure. This function is especially useful when shooting with reversal film, because of the film's low tolerance for exposure error. With the 800si, you can choose a series of 3, 5, or 7 frames. The exposures can be made in 0.3, 0.5, or 1.0 EV increments.

After the settings are entered, F br 1 appears in the data panel and the viewfinder.
Wait for the flash-ready signal to appear in the viewfinder. Press the shutter-release button all the way down to take the picture.
Customized Function #11 - Exposure Bracketing Sequence Setting 1 - The default exposure-bracketing sequence is NORMAL, , +. Setting 2 - The optional exposure-bracketing sequence is , NORMAL, +. In this setting, take care when making bracketing series at the end of a roll of film. The roll may finish before the NORMAL exposure is made. 78

Page 80

Repeat steps 3 and 4 until the series is complete.
The data panel and viewfinder will change to indicate the frame number in the bracketing series.

MULTIPLE EXPOSURE

The multiple-exposure mode lets you overlap up to 9 images on the same frame.
Flash bracketing is equivalent to fill-flash mode. Do not turn off or remove the accessory flash before the series is complete. The remaining shots will be exposed at the flash sync speed, causing the pictures to be underexposed. Flash bracketing will not operate with an accessory flash that is connected to the camera's PC terminal or the Vertical Control Grip VC700's PC terminal via a sync cord (the VC-700 is sold separately).
To cancel the flash bracketing series before it is complete, push the built-in flash down or turn the camera off.
Turn either control dial until the multiple exposure indicator appears in the data panel.

will start blinking.

Page 82
Turn either dial to select the number of exposures. CANCELLING MULTIPLE EXPOSURE
Cancel multiple-exposure mode by setting another drive mode.
It is also possible to change the number of exposures remaining in the multiple-exposure series after starting the series. Follow the instructions for Setting Multiple Exposure. The number of exposures set will be the number remaining. Example A: After starting a multiple exposure series, the number of exposures is changed to 1. Multiple exposure mode will cancel after the next exposure is made. Example B: After shooting 8 exposures of a multiple exposure series, the number of exposures is reset to 9. Multiple exposure mode will cancel after 9 more exposures are made. Values 0 - 9 are available.
Press the shutter-release button partway down to enter the setting. Press the shutter-release button all the way down to take the first picture.
M2 will appear in the data panel.
Repeat step 6 until all the exposures have been made.
Multiple-exposure mode is cancelled and the camera is automatically set to single frame advance after all the exposures have been made. If the battery is removed before a multiple exposure series is complete, multiple exposure will be cancelled, but the film will not have advanced to the next frame. Tell your photofinisher there are multiple exposure frames on the film. Some photofinishers may not automatically print multiple exposure frames. You may want to use exposure compensation to underexpose each exposure so the final image on the frame is not overexposed (p 74).

Frame your subject. While pressing the AE-lock button, press the shutterrelease button all the way down to take the picture.
If the background is bright or a large aperture is set (in A mode), the shutter speed may not be reduced. Use a tripod if the shutter speed becomes too slow to allow sharp, hand-held pictures after you press the AE-lock button.
The rear-flash sync function is designed to create action shots that leave a blur of motion behind the subject. Rear-flash sync requires a slow shutter speed to make the 'blur' exposure with the ambient light, then the flash fires to properly expose the subject. Using a slow shutter speed with conventional flash does not produce the same effect, as the flash exposure is made before the ambient exposure, so the blur motion comes after the subject and is unnatural.
Rear-flash sync can be used with the built-in flash and accessory flashes attached to the accessory shoe or PC terminal.
CAUTION: Customized Function #10 - AE-Lock Button Setting 2: The AE-lock button is pressed once to turn AE Lock/Slow-shutter Sync on, then must be pressed a second time to turn AE Lock/Slow-shutter Sync off. The AEL indicator will remain in the viewfinder when AE Lock/Slow-shutter Sync is on. See page 102 for more information.

Page 90

Turn either dial to display in the data panel.

FLASH COMPENSATION

This function enables you to bias the output of the built-in flash or an accessory flash as much as + or 3 EVs in.5 increments.
While pressing the flashcompensation button, turn either control dial. Press the shutter-release button partway down to enter the selection. Press the shutter release button all-the-way down to take the picture.
Select a shutter speed of 1/90 or slower. If a faster shutter speed is selected, will remain in the viewfinder, but a normal exposure will be made. Rear flash sync is not compatible with flash units that have a very long firing duration. An incomplete exposure will occur.
When the desired compensation factor appears in the viewfinder and data panel, release the button.

Control

Release Priority* Film Rewind Start Film Tip DX Memory Flash Control in P-Mode Lens Focus Hold Button (if applicable) Eyepiece Sensor Activation Frame Counter AF Area Selection AE Lock Button Exposure Bracket Sequence Film Rewind Speed Viewfinder Display Duration Show AF Area Eye-start Switch Built-in Flash Zoom

Action

AF Priority Release Priority Auto Manual Rewind into cartridge Out of rewound cartridge On Off Manual switchover Autoswitchover Focus hold Center-area select Continuous AF Grip switch Main switch Normal Counts down Wide or Local Center only while pressing AF button Active while button is pressed Active after button is pressed, cancelled after button is pressed again Normal, , + , Normal, + Silent (slow) Fast 5 sec. 10 sec. 30 sec. When AF button is pressed When focus is locked Turns eye-start on & off Turns dial-lock on & off, eye-start is always on Turns dial-lock on & off, eye-start is always off Linked with focal length Fixed to wide

17/10/97 11:00 AM

Page 104
All customized settings were set to1 before your camera was shipped.
Press the shutter-release button partway down to enter the selections.
Turning the camera off or removing the batteries will not affect the Customized Function Settings. Release Priority is the only customized function that can be set in memory. It is also the only customized function that can be changed by the memory-recall button and program-reset button.
CHANGING THE CUSTOMIZED SETTINGS While pressing the adjust button, press the ISO button.
Turn the front dial to select the number of the Customized Function.
In the example: Customized Function #3 - Film Tip has been selected.
Note: When Customized Function #15 - Eye-start Switch is on setting 2 or 3, the dials are completely disabled when the switch is set to ON. In this case, the only function the dials will operate is the Customized Setting.
Turn the rear dial to change the setting.
In the example: Setting 2 - (leaving the film tip out of a rewound cartridge) has been selected.
RESETTING ALL THE CUSTOMIZED SETTINGS TO 1 Press and hold the adjust button in the control panel. Slide the main switch to LOCK then return it to ON.
When the operation is complete, will blink in the data panel and every custom setting will be set to 1.
Repeat steps 2 and 3 until all the desired functions are selected.

Page 106

DATA MEMORY
When data memory is selected, the following information about each photograph is stored at the time of exposure:
Aperture Shutter speed Lens focal length Flash status (on/off) Exposure compensation Flash compensation (if used)

Turn either control dial until appears in the data panel. Press the shutter release button partway down to enter the setting.
Center your subject in the focus frame, then press the shutter-release button all the way down to start the timer.
The self-timer lamp will blink after the shutter-release button is pressed. Three seconds before the picture is taken, the self-timer lamp will blink rapidly. To cancel the self-timer before taking the picture, slide the main switch to LOCK. The self-timer is cancelled automatically after the shutter is released. If you are not looking through the viewfinder when the shutter-release button is pressed, light entering the eyepiece may affect the camera's automatic exposure settings. To prevent this, attach the eyepiece cap before starting the self-timer (p 11).

Page 118

FILM DRIVE MODES
The 800si has two film-drive modes: Continuous Advance and Single Frame Advance. In Single Frame Advance, the camera makes one exposure and advances the film one frame each time the shutter-release button is pressed. In Continuous Advance, the camera will release the shutter and advance the film (up to 3 frames per second) as long as the shutter-release button is held down.
Press the self-timer/drivemode button in the control panel.
Turn either control dial until appears in the data panel. Press the shutter-release button partway down to enter the setting.
When Autofocus Priority is selected, the shutter will not release until sharp focus is confirmed. To release the shutter even if sharp focus is not confirmed, change Customized Function #1 (AF Priority/Release Priority) to Release priority (setting 2). See page 69 and page 102. When the camera is in release-priority mode (RP), the shutter releases even if the subject is not in focus. Lens "Power Zoom" functions do not operate in Continuous mode (AF Zoom xi and AF Power Zoom lenses included).

Page 120

PROGRAM RESET BUTTON
Press the program-reset button to return the following camera functions to their program settings.

ACCESSORY INFORMATION

The Minolta 800si was designed to work specifically with lenses, flash units and other accessories manufactured and distributed by Minolta. Using incompatible products with this camera may result in unsatisfactory performance or damage to the camera or accessories.

Function

Exposure mode Subject Program Focus area Focus AF Mode Metering mode Exposure compensation Flash compensation Film-drive mode Self-timer Wireless Flash Rear-flash Sync Shutter-release mode

Is the battery installed correctly? Is the battery exhausted? Is M. FOCUS displayed in the data panel? Is the subject in one of the special focusing situations listed on page 30? How close is the camera to the subject?
Install a new battery if the battery is dead.
Press the Focus-mode button to select autofocus. Use focus lock or focus the lens manually. Make sure you are not closer than the minimum focus distance listed in the lens' instruction manual. Use a compatible lens and attach it properly. In AF priority, the shutter will not release unless sharp focus is confirmed. To release the shutter even if focus is not confirmed, switch to Release priority. Contact a Minolta Service Facility before attaching the camera to a telescope. Remove and reinstall the battery. If normal camera operation does not resume, contact a Minolta Service Facility.

31 27, 31 14,121

Shutter will not release.
Is the lens compatible? Is the lens attached properly? Is Autofocus-release priority (AF priority) selected? Is the camera attached to a telescope?
is displayed in the data panel. appears in the data panel. Is Data Memory on? Are all the film areas full?
To begin overwriting film area 1, take the next picture.

Page 126

CARE AND STORAGE
CLEANING If the camera or lens barrel is dirty, wipe it gently with a soft, clean, dry cloth. If the camera or lens comes in contact with sand, gently blow away loose particles - wiping may scratch the surface. To clean the lens surface, first brush away any dust or sand, then (if necessary) moisten a lens tissue with lens cleaning fluid and gently wipe the lens in a circular motion, starting from the center. Never place lens fluid directly on the lens. Never touch the interior of the camera, especially the mirror and shutter curtain. Dust on the mirror will not affect the picture quality. Never use compressed air to clean the camera's interior, doing so may cause damage to sensitive interior parts. Never use organic solvents to clean the camera. Never touch the lens surface with your fingers. BEFORE IMPORTANT EVENTS Check the camera's operation carefully or take test photographs. Minolta is not responsible for damages incurred by equipment malfunction.
STORAGE When storing your camera for extended periods, please follow these guidelines: Remove all batteries from the camera. Attach the protective caps. Store in a cool, dry, and well-ventilated area away from dust and chemicals (such as moth balls). For very long periods, place the camera in an airtight container with a silica gel drying agent. Periodically release the camera's shutter to keep it operating properly. Before using after prolonged storage, check the camera's operation to make sure it is functioning properly. 126