Mio DigiWalker C710

Navigation and Entertainment System
Is the Mio DigiWalker C710 a personal navigation device or a personal entertainment device? Yes. Designed for the fashion conscious traveler, the C710 combines highly accurate GPS navigation, comprehensive point-of-interest location, integrated Bluetooth and a feature-rich media player in a single device. On the road or on the couch, the C710 has got you covered.
All dressed up, with everywhere to go
The design of the C710 places it in a class by itself. Elegant and functional, this revolutionary device will look as good on your desk as it does on your dash. Completely self contained and ultra portable, the C710 slips easily into pocket, purse or briefcase and redefines the look of personal navigation.

Look Ma, no hands

For the ultimate in convenience, the C710 features integrated Bluetooth compatibility as well as a built in speaker and microphone. These features, when used in combination with your Bluetooth enabled cell phone will allow you to make and take phone calls in a completely hands-free fashion, using the C710 as a self contained speakerphone.

The show must go on

Much more than a simple navigation device, the C710 is a complete handheld home entertainment system. From the ultra bright, backlit screen to the built in speaker and headphone jack the C710 is the perfect companion for any road trip. View photos, watch movies or listen to your favorite songs, the C710 does it all and does it with style.
Style and accuracy combine to reinvent portable navigation.

It's where you're going.

47988 Fremont Blvd. Fremont, Ca 94538 | 1-866-MIO-4-GPS

Specifications

GPS Receiver Channels Memory Display Storage Format TMC Support Battery USB Weight Dimensions (WxHxD) 20 (SiRFstarIII), WAAS Enabled 2GB ROM, 64 MB RAM 3.5" TFT with touch screen and 65k colors SD/MMC memory expansion slot Built-in TMC Receiver 1200 mAh Li-ion (up to 5 hours) V1.oz (170 grams) 4.33" x 3.03" x 0.78"
Minimum System Requirements
Microsoft Windows 2000 or XP or later Microsoft Outlook 2000 or later Microsoft Internet Explorer 6.0 or later USB port DVD-ROM drive
Hands-Free Calling Simply tap the screen to receive and make calls while driving. The built-in Bluetooth manager connects with compatible Bluetooth cellphones.
Built-in Media Player With the C710's mutimedia functions, viewing pictures as well as playing videos and music is simple and easy.
TMC Traffic Reports for Smarter Routing Avoid traffic jams with TMC. The integrated TMC receiver picks up real-time traffic information that automatically creates faster routes.
Includes everything you need to hit the road in style

Carrying Case

Device Holder

Windshield Mount

Car Charger

USB Cable

AC Adapter

TMC Antenna

Application CD, Map DVD
47988 Fremont Blvd. Fremont, Ca 94538 | 1-866-MIO-4-GPS | www.mio-tech.com

User Manual

MioMap v3.2
Navigation software for Mio DigiWalker C710
UK English August, 2006 (v1.00)

Copyright note

The product and the information contained herein may be changed at any time without prior notification. This manual nor any parts thereof may not be reproduced or transmitted in any form either electronically or mechanically, including photocopying and recording, without the express written consent of Mio Technology Limited. 2006 Mio Technology Limited 2006 Nav N Go Kft. Whereis map data is 2006 Telstra Corporation Limited and its licensors Data Source 2006 Tele Atlas N.V. Austria: BEV, GZ 1368/2003 Denmark: DAV France: IGN France Great Britain: Ordnance Survey data with permission of Her Majestys Stationery Office Crown Copyright Italy: Geonext/DeAgostini Northern Ireland: Ordnance Survey of Northern Ireland Norway: Norwegian Mapping Authority, Public Roads Administration / Mapsolutions Switzerland: Swisstopo The Netherlands: Topografische ondergrond Copyright dienst voor het kadaster en de openbare registers, Apeldorn All rights reserved.
Thank you for choosing MioMap as your door-to-door in-car navigator. Read the Quick Start Guide first and start using MioMap right away. This document is the detailed description of the software. Although MioMap can easily be discovered by experience, it is still recommended that you read through this manual to clearly understand the exact function of each button and icon.

Table of Contents

Warnings and safety information... 8 General information... 9 Operating MioMap (Controls)... 10 3.1.1 Power on/off... 10 3.1.2 Main menu... 10 3.1.3 Volume up and down buttons... 10 3.2 Screen buttons and controls... 11 3.2.1 Direct selectors... 11 3.2.2 List selectors.... 11 3.2.3 Sliders.... 11 3.2.4 Switches... 12 3.2.5 Switches in the Quick menu... 12 3.2.6 Virtual keyboards... 12 3.2.6.1 QWERTY-type keyboards... 13 3.2.6.2 The numeric keyboard... Discovering the program through the screens.. 14 4.1 The map.... 14 4.1.1 2D and 3D map views... 14 4.1.2 Zoom levels... 15 4.1.3 Daylight and night colour schemes... 15 4.1.4 Streets and roads... 16 4.1.5 Other objects... 17 4.1.6 Speed cameras... 17 4.1.7 Contacts.... 17 4.1.8 Elements of the Active Route.. 17 4.1.8.1 The start point, via points and the destination.. 18 4.1.8.2 Animated turn guidance... 18 4.1.8.3 The route line.... 18 4.1.8.4 Roads in the route excluded by your preferences.. 18 4.2 Screens with map... 19 4.2.1 Turn preview (No. 1)... 21 4.2.2 Zoom in and out (No. 2 & 3)... 21 4.2.3 Tilt up and down (No. 4 & 5)... 21 4.2.4 Lock to GPS position and heading (No. 6).. 22 4.2.5 Cursor (No. 7)... 22 4.2.6 Map scale (No. 8)... 23 4.2.7 Menu (No. 9).... 23 4.2.8 Map orientation and Overview (No. 10)... 23 4.2.9 GPS position quality (No. 11).. 24 4.2.10 Battery status (No. 12).. 25
4.2.11 Bluetooth or Phone call status (No. 13)... 25 4.2.12 Track Log recording/playback indicator (No. 14).. 25 4.2.13 Cursor menu (No. 15)... 26 4.2.14 Current street (No. 16).. 28 4.2.15 Travel and Route data (No. 17)... 28 4.2.16 Distance to next turn (No. 18)... 28 4.2.17 Next street / Next settlement (No. 19).. 28 4.2.18 Approaching next turn (No. 20)... 29 4.2.19 Current speed limit (No. 21)... 29 4.3 GPS Data screen.... 29 4.3.1 GPS data displayed... 29 4.3.2 GPS connection indicator.. 30 4.3.3 GPS data quality indicator... 30 4.3.4 Time synchronization... 31 4.4 Route Information screen... 31 4.4.1 Route data displayed (for destination and via points).. 31 4.4.1.1 Route line... 32 4.4.1.2 Distance Left... 32 4.4.1.3 Method.... 32 4.4.1.4 Time Left.... 32 4.4.1.5 Estimated Arrival.... 33 4.4.1.6 Destination / Via point... 33 4.4.2 Warning icons... 33 4.4.3 Fit to screen... 34 4.4.4 Parameters.... 34 4.5 Menu.... 34 4.5.1 Find tab.... 34 4.5.2 Quick tab... 35 4.5.2.1 Zoom & Tilt (switch)... 35 4.5.2.2 Daylight & Night Modes (switch)... 35 4.5.2.3 Manage POI (Points of Interest).. 36 4.5.2.4 Popup Information (switch).. 39 4.5.2.5 Manage Track Logs... 39 4.5.3 Route tab.... 41 4.5.3.1 Recalculate... 41 4.5.3.2 Delete.... 42 4.5.3.3 Itinerary... 42 4.5.3.4 Fly Over... 44 4.5.3.5 Edit... 44 4.5.3.6 Info... 45 4.5.4 Main button.... 45 4.6 Speed cameras... 46 4.6.1 Camera types... 46 4.6.1.1 Fixed cameras... 46 4.6.1.2 Mobile cameras... 46 4.6.1.3 Built-in cameras... 47 4.6.1.4 Section control cameras... 47 4.6.2 Controlled traffic direction.. 47 4.6.3 Speed limit checked... 48 4.6.4 Add a new camera or edit an existing one.. 48

Tap the icon to hang up the call. The icon is then returns to the blue Bluetooth logo.

4.2.12

Track Log recording/playback indicator (No. 14)
When a track log is being recorded, a red icon is displayed on the map screens. This icon also functions as a button leading to the Track Log screen (Page 39) where you can stop the recording or make the track log visible on the map.
During track log playback a green icon will blink. Tapping this icon (in fact, tapping the screen anywhere) stops the simulation.

4.2.13

Cursor menu (No. 15)
The Cursor is the selected point on the map (marked by a red dot and radiating red circles around it), or the current GPS position when it is available and Lock-toPosition is enabled. When you tap the screen to place the Cursor, the Cursor menu pops up automatically to give you the list of possible functions you can use the Cursor for. At the same time Popup Info (street name, house number and the list of POIs nearby) appears near the selected map point if Popup Info is enabled in the Quick menu (Page 36). If you do not use the Cursor menu in a few seconds, it will automatically vanish back to the bottom of the screen, and Popup Info disappears, too. You can have them reappear by reopening the Cursor menu using the arrow in the bottom right corner. When you open the menu manually, it will stay on until you close it or switch to another screen. Tip: If you want to see the map around the Cursor, close the Cursor menu and reopen it. When this menu is opened manually, the map is always moved to have the cursor in the centre. The content of the Cursor menu depends on the screen (Map or Cockpit) and it is slightly different if there is an active route already planned. You have the following options: Start: use the Cursor as the departure point for your route. This menu point is available only in Map mode and when there is no active route. In Cockpit mode the departure point of the route is always the GPS position or if it is not available, the last known GPS position. Route To: use the Cursor as the destination of your route. This button is to start a new route. The previous route (if it exists) will be deleted and replaced. If a multipoint route is active, MioMap will ask you whether you really want to delete it together with all its via points. Add Via: by inserting the selected map point as a via, you instruct MioMap to cross this location before the destination of the route. This is the way to build a multi-point route in reverse order (when you wish to insert a stopover go to A but first get some fuel at B or want to influence the direction of the route). This menu point works only if a route is already active. Remove Via: removes the via point near or at the Cursor. The route will be recalculated immediately excluding the deleted point. This menu point replaces Add Via and is available only if the Cursor is near or at a via point.

4.4.1.5 Estimated Arrival This is an estimated value that can also be displayed in one of the Route data fields on the Cockpit screen as ETA to destination. It shows the estimated arrival time at the final destination of the route based on information available for the remaining segments of the route. The calculation cannot take into account traffic jams and other possible delays. If via points exist, tap and tap again any of the fields to see the estimated arrival at the first, second, etc. via point. 4.4.1.6 Destination / Via point This field shows the exact address (or its coordinates if the address is not available) of the final destination. If via points exist, tap and tap again any of the fields to see the address or coordinates of the first, second, etc. via point.

4.4.2 Warning icons

The following 5 squares are normally grey. Some of them turn red and show a graphical symbol in case warning(s) are attached to the planned route. These are warnings, so icons always show information for the whole route, even if the data fields display values from your current position to a via point only. Click on any of the icons to show its description. A few samples of the available icons:
This icon shows that you need to pay toll on the recommended route. This icon shows that the route contains motorways. Tap the icon to see the total length of the motorways in the recommended route. This icon shows that toll roads are included in the recommended route. This icon shows that you need to board a ferry along the recommended route.
This icon shows that you need to pay for the ferry. This icon is displayed when MioMap could not plan a route with all your road type preferences respected. Sometimes it is impossible to find a suitable route near the start or the destination.
This icon warns you that MioMap had to recommend a route that does not match all your preferences given at the Route Parameters settings. The recommended route contains areas only accessible to pedestrians. The recommended route contains unpaved roads. The recommended route contains roads that require a permit or permission to enter. Information any other piece of relevant but not categorised information. Tap the icon to see the content. Next page displayed when more than 5 warnings apply for the recommended route.

4.4.3 Fit to screen

Tap this button to display an overview of the whole recommended route. You will jump to the Map screen with a 2D North-up view so that you can check where the route takes you.

4.4.4 Parameters

This button opens the Route parameter settings screen (Page 69) otherwise opened from the Route menu (Page 41).

Manage My POI By highlighting then tapping again the My POI switch on the Manage POI main screen you can manage the POI groups and items that you have created.
Note: The group Unnamed only appears if you have previously saved a POI item without creating a new POI group for it. Note: If there are valid entries in the Contacts application of your Mio DigiWalker C710, the ones MioMap can recognise the address in will be imported as My POIs, added to a new group named Contacts. Each time MioMap starts, it reloads the points from the Contacts application database. With the help of these points you can plan a route to any of your contacts by only a few screen taps. Tapping any of the group names will open a list of POIs saved in that group. This list is similar to the list of POI results in Find. The POIs are ordered based on their distance from your current position. If GPS position is not available or you have disabled Lock-to-Position by tapping the map, the POIs will be ordered by their distance from the Cursor.
When the My POI Groups are displayed, you have the following options: Show/Hide: similarly to built-in POIs, you have the possibility to show or hide all POIs of the selected category on the map. Groups with a blue icon are displayed; groups with a grey icon are hidden. New: you can create a new My POI group by tapping this button. You need to select an icon, a name, and the maximum zoom level at which the POI is still visible on the map (provided you let the POI group be displayed at all). You do not 37
necessarily need to create POI groups in advance. You can do it while saving a new POI. Delete: you can delete any of your previously saved My POI groups. This will delete all POIs in that group. MioMap will ask you to confirm this action. Edit: you can edit the attributes (name, icon, visibility level) of a previously created My POI group.
Left/right arrows: if your groups fill several pages, these buttons will let you browse through them. The green field left of these buttons shows the current page number and the number of pages.
When the list of My POIs is displayed, you have the following options: Filter: you can shorten the list of matching POI items by filtering. Just like in Find, enter a few letters of the desired POI name. When the number of matching items can fit in one page, MioMap will automatically display the list. If you tap Done any time before this happens, you receive the list of matches on multiple pages. ABC/Distance: by tapping this button you can have the POIs sorted in an alphabetical order. Tapping again will return to the distance-based order.

Display modes are different only in the number of events displayed in the list. List items are always shown with all information available including pictograms of the needed action and distance of the event from the previous list item. The Itinerary is live and constantly updated when navigating a route. The list item coming next in navigation is the highlighted one until you highlight another one by tapping. After that, the highlight remains on the item you have selected. Detailed Instructions: this is the list displayed when Itinerary is opened. It is the list of events in full detail. All significant junctions are shown in the list, even ones to be passed. Instructions: by tapping the Mode button once you will see the list of events that need your attention, i.e. the list of manoeuvres during the route. These are the events shown in the Turn preview field and announced by the voice instructions. Route summary: tapping the Mode button again will show an overview of the route that contains only the significant roads and intersections.
Show Tap this button to see the highlighted list item on the map. This will help you identify route events in the list. Avoid Tap this button to show a list of possibilities for modifying the route. They let you recalculate the route avoiding the highlighted event and sometimes also some of the subsequent ones.
Manoeuvre: this option avoids the highlighted action. For example if you find a turn too difficult during rush hour traffic, MioMap will recalculate the route excluding that turn. If the next street is important in the route, it is likely that MioMap will replace the turn with several easier ones to get to the same street. Road: when you exclude a road, MioMap will calculate a route that does not use that road. It is useful when you anticipate a traffic jam in a street used in your route, or a roadblock is announced on the radio, and you find that road in your Itinerary. Distances: you can also find some distance buttons in this list. They are similar to the ones in the Bypass list of the Recalculate menu (Page 41), but these can also be used for distant parts of the route.
Note: You need not open Itinerary if you run into a roadblock or traffic jam. To get an immediate alternative route use the Bypass function of Recalculate (Page 41). Note: When you use this feature, MioMap will keep on excluding the same part of the map from later routes until you manually delete the route (Page 42), or restart MioMap. 4.5.3.4 Fly Over This feature has no navigation function, it merely provides a quick view of the route. It will present a simulation of the route showing what you will see later when navigating. There are two possibilities for running the simulation. Fast Fly Over Tap Fly Over to quickly run through the route. MioMap will fly the route in Cockpit mode at high speed to give you a rough overview of the route events. MioMap is tweaked to give you a smooth and easy-to-follow playback even at this speed. Press and hold the Main menu button (Page 10) then tap Fly Over to quickly run through the route. MioMap will fly the route in Cockpit mode at high speed to give you a rough overview of the route events. MioMap is tweaked to give you a smooth and easy-to-follow playback even at this speed. This mode is useful if you want to have a look at the route before you start your journey. Tap anywhere on the screen to stop the simulation. Lifelike simulation Tap the Fly Over button without pushing any hardware buttons. In this mode the simulation is run at normal speed (using the speed limit of the streets and roads in the route), and voice instructions are also played. This mode is mainly useful for demonstrating MioMap, or to learn the way it works before your start your first journey. 4.5.3.5 Edit Tap Edit to see the list of all points used in the route. The first item in the list is the departure point of the route without a valid GPS position, the last reached via point if you open the list during navigation, or the point where MioMap most recently recalculated the route. This means the list is permanently updated, and via points drop out during the journey. The last item in the list is your final destination.

Use the arrows on the right to browse through the list and tap any line to highlight it. You can perform the following operations: Add: you can add a new route point (or a new final destination if the highlighted item is the last one in the list) after the selected point. The Find menu opens automatically to let you search for an address, POI, coordinates, one of your favourite destinations, or select a point from the History list. As soon as you select any of these, MioMap returns to the Edit screen and your selection appears right under the highlighted line. Delete: you can delete the selected point from the list. If the highlighted item is the last one in the list, the previous via point will be promoted to be the final destination. Optimise: you can optimise the order in which you will drive through the via points, if there is no specific order you would like to keep. When tapping this button, MioMap reorders the list instantly to save you time and fuel. Optimisation is for via points only. Your starting point and destination remain in their positions, of course. Up and Down: using these buttons you can reorder the list by moving the highlighted item up or down in the list.
4.5.3.6 Info This button opens the Route Information screen described here: Page 31. This screen shows information about the current route and has a few additional options to check and modify your active route.

4.5.4 Main button

The Main button at the bottom right corner leads to the Main menu screen described here: Main menu.

4.6 Speed cameras

There is a built-in database of fixed and mobile speed cameras. It is also possible to add new cameras to enhance this database. MioMap can warn you when you approach one of these cameras. You can fine-tune this warning in General settings (Page 63). Speed cameras are displayed with small camera symbols on the map.

4.6.1 Camera types

There are four types of speed cameras: 4.6.1.1 Fixed cameras Some cameras stand by the roadside, looking in one direction, measuring one or both directions of the traffic. They measure your current speed. For these cameras you can specify the controlled traffic direction and the speed limit. MioMap will warn you when you approach these cameras in the measured direction. If your speed exceeds the speed limit near the camera, a special warning sound will be played. These cameras are displayed with the following symbol:

4.7 TMC (Traffic Message Channel)
MioMap can provide you with even better routes if Traffic Message Channel (TMC) information is available. The TMC is a specific application of the FM Radio Data System (RDS) used for broadcasting real-time traffic and weather information. Note: TMC is not a global service. It may not be available in your country or region. Ask your local dealer for coverage details. You need a TMC receiver attached to your PNA to receive TMC information. The Mio DigiWalker C710 already contains the TMC receiver, and only needs a suitable antenna attached to the phones connector. MioMap automatically takes into account the TMC information received. You do not need to set anything in the program. The receiver will automatically search the FM radio stations for TMC data, and the decoded information will immediately be used in route planning. The moment MioMap receives traffic information that may affect your route, the program will warn you that it is recalculating the route, and navigation will continue with a new route that is optimal considering the most up-to-date traffic conditions. The TMC subsystem can be started from the GPS Data screen (Page 29) by tapping the TMC button.
4.7.1 List of TMC messages
The main screen of the TMC section is the list of valid TMC messages ordered by their distance from your current location.
Tap the arrows to turn the page, and see traffic difficulties farther away from your current position, or press Settings to configure the TMC subsystem. This opens a new window.

4.7.2 TMC control centre

This screen shows the selected TMC source and allows you to change the TMC settings.
4.7.2.1 Selected FM radio station The name and frequency of the selected radio station will appear at the top of this window, together with signal strength information indicated by a bar similar to the GPS satellite signal strength bars on the GPS Data screen. If there arent any radio stations broadcasting TMC data in your area, the receiver keeps on searching. You will see the frequency continuously sweeping across the FM CCIR radio band (87.5-108 MHz). When you move to an area with TMC information, the indicator will show the frequency, and detailed information for the TMC station. 4.7.2.2 Exclude selected station If you wish to receive TMC data from another radio station, push this button. The radio station will be added to the list of excluded stations, MioMap will start searching for another TMC station, and will always skip the excluded station in the future. 4.7.2.3 Show excluded stations This button opens the list of excluded radio stations. Tap any of the stations in the list, then tap Enable to allow MioMap to accept TMC information from this station.

4.7.2.4 Sorts events by distance / type The list of traffic events can be ordered by their distance from the current position, or by their type. Tap this button to toggle between the two possibilities.
4.7.2.5 Use traffic information This button is enabled by default, which means that TMC messages are used in route planning. Tap this button to have MioMap ignore real-time traffic information when planning routes. Tip: If you make a route planning for a future journey, it may be better to turn off TMC corrected route planning. 4.7.2.6 Recalculate to avoid traffic This setting is similar to the previous one. Disabling it will not prevent the system from using TMC data for route planning, but will not trigger an automatic recalculation when the traffic conditions change during your journey.

5 Find

One of the most frequently used functions of MioMap is selecting the destination. Once you have the destination, you can start navigating. Getting to this point should be as fast as possible. MioMap provides you with a versatile search engine designed to find your chosen destination after only a few taps on the screen. Note: If you select a location in any part of the Find system, you will normally drop back to the map screen, where you will have several possible actions (set as start, set as destination, add as via, continue route with, mark with a pin, or add as a POI item). However, if you enter the Find system from the Main Menu, MioMap will immediately put you into Cockpit mode and start navigation.
5.1 Main menu Find buttons (Address, Favourites, POI, History)
As just mentioned, the fastest way to find your destination and start navigating is to start from the Main Menu (Main menu) with one of the Address, Favourites, POI or History buttons. These will put you on the respective Find screen, and as soon as you pick a destination, MioMap will immediately show the Cockpit screen and start navigation. This means that if you plan your route to one of your Favourite destinations, you only need two taps (e.g. Favourites then Home) to start navigating. You will find similar buttons in the Find menu (Page 53) accessible from the map screens. Activated from the map screens, they will only move the cursor to the desired location, but will not directly initiate navigation.
5.2 Selection by tapping the map
It is also very easy to set your destination using the map. Just browse to your desired destination on the map, tap it, and the Cursor menu with the possible actions will then open automatically. Note: When appearing automatically, the Cursor menu remains open for a few seconds only. If you decide not to choose any of the actions listed, the menu closes
automatically. When you open it manually, it will remain until you close it or switch to another screen. Tip: If you want the selected point shown in the centre of the map, close and reopen the menu or wait until it closes and open it again. By opening the Cursor menu manually, the map will be moved to have the selected location in the centre.

6.1.3 Speed Warning Options
When speed warning is turned on, the values of these controls determine when the warning will be triggered.
You can set two different kinds of behaviour for the warning: one is applied up to a certain speed limit and the other one is used above that. 6.1.3.1 Speeding tolerance MioMap will warn you when you exceed the speed limit by the amount specified here. Select whether you want to specify the tolerance as a Fixed value (offset to the speed limit) or as a Percentage. The slider will change depending on which mode you have chosen. Both positive and negative values can be given in either offset or percentage mode. 6.1.3.2 Alternative speed limit If the speed limit of the current road segment equals or is above this limit, the speed warning will use the alternative tolerance instead of the previous one. Move the slider to its rightmost position to turn off the alternative speed warning. Then the settings of the upper slider will determine the warning for all roads. 6.1.3.3 Alternative speeding tolerance If the speed limit of the current road reaches the value set at Alternative speed limit, this setting will replace the basic one set at the top of this screen. The slider and the selector work exactly as the basic ones described here: Page 64.
Example: to let you better understand how this feature works, here is an example. If you use the setting on the left (portrait) screen example (+10 km/h 100 km/h +5%), MioMap will warn you when driving at the following speeds:
Speed limit 40 km/h 60 km/h 90 km/h 100 km/h 120 km/h 160 km/h Warning at 50 km/h 70 km/h 100 km/h 105 km/h 126 km/h 168 km/h (=40 km/h + 10 km/h) (=60 km/h + 10 km/h) (=90 km/h + 10 km/h) (=100 km/h + 5%) (=120 km/h + 5%) (=160 km/h + 5%)
6.1.4 Enable Speed Camera Warning
MioMap contains a built-in database of known speed and red light cameras, and you can also add further cameras you discover using the Add Cam button in the Cursor menu (Page 26). The types and parameters of speed cameras are explained here: Page 46. In this section you can enable or disable the warning for known cameras, and you can also fine-tune the way MioMap warns you when you approach one of these cameras.
6.1.5 Speed Camera Options
When speed camera warning is turned on, the values of these controls determine how the user will be notified when approaching a speed camera.

6.1.7 Route Recalculation
Once a route is planned, this setting will tell MioMap what to do when you deviate from that route. 6.1.7.1 Automatic The route will be recalculated automatically a few seconds after you go astray. 6.1.7.2 Disabled If you stick to the original route, and you wish to get back to it on your own, you can disable recalculation. This way guidance will stop until you return to the recommended route on your own.

6.2 Sound settings

Settings on this page determine the way MioMap sounds.
6.2.1 Master sound volume/switch
The loudness of MioMap is independent of your PNA settings. When you run MioMap, the position of this fader determines the device volume level. When you exit the program, the device settings return. The left part of this control works as a mute button. Tap to mute all MioMap sounds.
6.2.2 Voice guidance volume/switch
The switch on the left can turn on or mute MioMap's audible guidance (voice instructions and speed camera warning). When turned on, the slider on the right will adjust the loudness of voice prompts. In its leftmost position the voice guidance is suppressed, in its rightmost position the master volume applies.
6.2.3 Key sound volume/switch
The switch on the left can turn the key sounds on or off. Key sounds are audible confirmations of either pressing hardware buttons or tapping the touch screen. When key sounds are turned on, the slider on the right will adjust their loudness. In its leftmost position the key sounds are suppressed, in its rightmost position they are played at the master volume level. Note: The sound effects of MioMap are context sensitive. They will be different if, for example you open or close a window, or you enable or disable a setting. They will even let you know if you have entered enough letters of a street name to have a short list of matching streets on the screen.

6.2.4 Dynamic Volume

When driving at high speed, the noise in the car may be too loud to clearly understand the voice guidance messages and to perceive the key sounds. Using Dynamic Volume you can instruct MioMap to increase the volume when your speed exceeds a certain minimum, and reach its highest volume (determined by the Master volume slider in Sound settings) at the given maximum speed. Tap the Dynamic Volume button to turn on the feature. This will also open the screen where you can set the minimum and maximum speeds.

6.4 Language & Units

Here you can set the languages, measurement units, and date and time formats used by MioMap.

6.4.1 Program language

This button displays the current written language of the program. By tapping the button you can select from a list of available languages. MioMap will have to be
restarted if you change this setting. MioMap will ask for confirmation before it restarts.

6.4.2 Voice language

This button shows the current language of the voice guidance. By tapping the button you can select from a list of available languages and speakers. Tap any of these to hear a sample voice prompt. Just tap OK when you have selected the new spoken language.

6.4.3 Units

You can set the distance units to be used by the program. MioMap may not support all of the listed units in some voice guidance languages. If you select a measurement unit that is not supported by the chosen voice guidance language, you will see a red warning message under the selector.
6.4.4 Set Date & Time Format
You can set the date and time format displayed by MioMap. Various international formats are available.

6.5 Advanced settings

These screens let you set a large number of different advanced settings and initiate some special functions. These settings and functions are divided into groups.
Tap on any button to set the corresponding parameters.All but the last one will open new windows where you can make your desired changes.

6.5.1 Cockpit settings

These settings determine how MioMap displays different content elements of the Cockpit screen.
6.5.1.1 3D in Cockpit mode (and track-up orientation) The normal use of the Cockpit mode is cruising or navigating, when the road lying in front of the driver is the most important part of the map. It is usually done in a 3D view with the current direction towards the top of the map. By default MioMap uses the same look of the map in both Map and Cockpit modes. Use this switch to instruct MioMap to always open the Cockpit mode in 3D with Track-up orientation (automatic map rotation) for driving purposes. Note: You will still have the possibility to switch the map to 2D view or north-up orientation, but the map will return to 3D mode with map rotation whenever Cockpit mode is started. 6.5.1.2 Cockpit screen layout There are three route data fields on the left of the Cockpit screen. Their content is fixed in Cruise mode (when there is no active route), but for Navigation mode you can change their content here. The available values are listed here: Page 28.

6.5.4 Map options

You can set a few parameters determining the appearance of the maps in MioMap.
6.5.4.1 Daylight / Night colour profile MioMap comes with different colour schemes for both daylight and night use. There is always one selected daytime scheme and one selected night-time scheme. MioMap uses these when switching from day to night and back. Tap the appropriate button and select a new scheme from the list. 6.5.4.2 Show Street Labels You can set whether or not to see the names of the streets and the POI icons on the map when driving. Based on the current zoom and tilt levels, street names are displayed either aligned with the street or on signposts stuck into the streets (Page 16). If you switch these signs on, it will be easier to recognise your location on the map, if you turn them off, it will be easier to see the road geometry. Note: You can only disable street names and POI icons if MioMap follows your position. As soon as you move the map and Lock-to-Position (Page 22) is disabled, street names and icons become visible again. Tap Lock to re-enable Lock-toPosition and have the labels and icons disappear again. 6.5.4.3 Textured Polygons Enable textured polygons, and have rivers, lakes, forests and other large objects displayed in a more realistic and attractive way on the map. Disabling it will lead to uniform areas but better performance. See Page 17.

6.5.5 Smart Zoom

Smart zoom is a lot more than just a usual automatic zoom. While navigating a route: when approaching a turn, it will zoom in and raise the view angle to let you easily recognise your manoeuvre at the next junction. If the next turn is at a distance, it will zoom out and lower the view angle to be flat in order to let you see the road in front of you, or it can even switch to an Overview mode to let you follow your position on the map. While cruising: if there is no active route and you are just driving, Smart Zoom will zoom in if you drive slowly and zoom out when you drive at high speed.
6.5.5.1 Enable Smart Zoom Use this switch to enable or disable Smart Zoom. When disabled, the zoom and tilt levels on map screens during navigation are fixed, and you can set them manually using screen buttons (Page 21 and Page 21). Turn this feature on to let MioMap zoom and tilt the map automatically to always show you the best view for your navigation needs. 6.5.5.2 Enable Overview mode You can configure how the Overview mode is triggered when the next turn is at a distance. The Route event distance will determine when MioMap switches to the Overview or back to the Navigation view. The Overview zoom level will determine the fixed zoom level of the map in both automatic and manually selected (by the Map orientation icon see here: Page 23) Overview modes. You can change the zoom level manually at any time (the Lock button will not be displayed), but when you enter the Overview mode again, the zoom level will be reset to this value. You can also move the map in Overview mode. Then the Lock button will appear, and when pushed, it will move the map to have your current position in the middle again. Note: when this automatic feature is disabled, you can still enable the Overview mode manually as described here: Page 23. 6.5.5.3 Keep position on road (Lock-on-Road) MioMap is normally used for vehicle navigation, therefore Lock-on-Road will display the position arrow precisely over roads, seamlessly correcting small GPS errors. For pedestrian use you may consider disabling Lock-on-Road to make MioMap always show your exact position. Note: By turning off Lock-on-Road you also turn off the GPS position error filtering. The position shown on the map will be subject to all position errors and position fluctuations.

6.6 About screen

Tap About on the Main menu screen to open this screen. The About screen is not used in normal navigation. It is there to inform you about the map licenses you have, the creators of MioMap and the legal aspects of using the program.

7 Troubleshooting guide

Thank you again for purchasing our product. We hope you will enjoy every minute of using it. However you may face difficulties before you get really accustomed to MioMap. In such cases, please, refer to this table of frequently encountered problematic situations. I cannot find the Greenarrow that would show my location. Navigation does not start. Check the GPS status icon on any of the map screens (Page 24) or the GPS Data screen (Page 29). It is likely that the GPS cannot determine your position. Move the GPS out of cover to get a position fix. The GPS is connected, sending valid position data, yet I cannot see the Greenarrow that would show my position. You should see a large semi-transparent Lock icon (Page 22) on the screen. Tap this to re-enable the Lock-to-Position feature that moves the map back to your actual location. The Green arrow shows my location, but I cannot see the route (Orange or red line), and no voice instructions are announced. It is likely that you have no active route. Check the upper left corner of the Cockpit screen (Page 21) if you can see the indication for the next turn or not. If this field is blank, you have no route planned, so you need to create one first. It is a common mistake to find a destination, show it on the map, but forget to tap the Route To button in the Cursor menu (Page 26) to create the route. Be sure to follow these steps, or always plan your routes by using one of the buttons on the Main menu screen. This will ensure your route is calculated automatically as soon as the destination has been selected. I cannot see the Lock button on the screen, yet the map is not rotated during driving. Look for a small, red N letter on the compass icon (Page 23) or an aeroplane icon instead of it. It is likely that you had initiated the North-up map orientation or the Overview mode unintentionally. Tap this icon to revert to Track-up mode with automatic map rotation. Creating a multi-point route I have tapped the Route To button once for each destination but only the last one appears in the list, all previous points have disappeared.