MM212 | Friction Dashboard Mount for Mio Moov 200 Series
Package Contents: (1) CM012 - Weighted friction dashboard mount (1) CM014-2 - Travelmount mini windshield mount (1) APMM200 - Dual-T to Mio Moov 200 pattern adapter plate (1) Optional adhesive safety hook (recommended but not required) (1) Alcohol cleaning pad Compatible with: Mio Moov 200 Series Navman S30 3D GPS
Patent Pending Friction Dashboard Mount with Pedestal Adhesive Safety Hook
APMM200 Adapter Plate for Mio Moov 200
Do not place mount in or near an air bag deployment zone or where it will obstruct view of the road.

Dash Mount Installation

Step 1. Find a safe location on the vehicle dash that is not in an air bag deployment zone. Step 4. Lower the pedestal onto the disc and press down firmly. Flip the locking lever down to secure the pedestal to the dash mount.

AIRBAG

Step 2.
Optional Safety hook installation will add extra stability. Clean the area with the included alcohol pad and let dry. Remove the adhesive backing on the safety hook base. The hook curve must point towards the windshield. Press and hold the hook down on the dash surface for about a minute. Allow 24 hrs. to cure to the dash at room temperature (72 F).

Step 5.

Adjust the angle of the arm by tightening the rotation knob.

Hook towards windshield

Step 6. Step 3. Place the loop on the back of the dash mount around the safety hook and place on the dash in front of the hook.
Adjust the lateral angle of the pedestal head by tightening the head adjustment knob.

Continued on next side.

Safety Precautions Do not install Arkon products over an air bag cover or within the air bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or air bag deployment. Arkon is not responsible for any damages caused to your car, your device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists www.arkon.com Consumer Hotline: Arcadia, CA 91006 USA USA (800) 841-0884 Designed in USA | Made in China and Taiwan INTL (626) 254-9005 Copyright 2008 Arkon Resources, Inc. Monday - Friday 9 am - 5 pm, PST
MM212 | Friction Dashboard Mount for Mio Moov 200 Series - Continued
Connect Adapter Plate to Mio Moov 200 Series Device Step 1. Connect the Moov adapter plate to Moov 200 device (not included, sold separately) by placing the feet (A) of the adapter into the corresponding notches (B) on the bottom of the device. Holding the thumb tab down (C), insert the upper tooth (D) into the recessed slot on the back of the device.
Connect Mio 200 Series Device to Dashboard Mount Step 1.
Connect the dual T-slots (E) on Moov 200 adapter plate to the dual T-tabs (F) on the dashboard mount head.

MM223 | Cup Holder Mount for Mio Moov 200 Series
Package Contents: (1) CM033-2 - Cup holder pedestal mount (1) APMM200 - Dual-T to Mio Moov 200 pattern adapter plate
APMM200 Adapter Plate for Mio Moov 200

CM033-2 Cup holder mount

Compatible with: Mio Moov 200 Series Navman S30 3D GPS
All brand names and product names are trademarks or registered trademarks of their respective owners.

Patent Pending

Do not place mount in or near an air bag deployment zone or where it will obstruct view of the road.
Cup Holder Mount Installation Step 1. Connect the post (A) to the cup holder base (B) by aligning the groove on the base to the ridge inside the bottom of the post.

(D) Angle adjustment nut

Connect Adapter Plate to Mio Moov 200 Series Device Step 1. Connect the Moov adapter plate to Moov 200 device (not included, sold separately) by placing the feet (F) of the adapter into the corresponding notches (G) on the bottom of the device. Holding the thumb tab down (H), insert the upper tooth (I) into the recessed slot on the back of the device.
(C) Thumbwheel adjustment knob

(A) Cup Holder Post

F G (B) Cup Holder Base

Step 2.

Place the universal cup holder mount into the designated cup holder in the vehicle. Adjust the thumbwheel adjuster (C) to expand or close the cup holder prongs to fit in the cup holder. For oversize cup holder openings or the adjustable pop out cup holders use the optional self-adhesive side support pads (E). Install the pads by removing the adhesive backing and placing it on the flat surface side of the cup holder support leg.
Connect Mio 200 Series Device to Cup Holder Mount Step 1. Attach the device to the pedestal by inserting the dual T-Tabs on the pedestal head (J) into the T-slots on the adapter plate (K).

Step 3.

(E) Optional support pads
Safety Precautions Do not install Arkon products over an air bag cover or within the air bag deployment zone. Arkon Resources, Inc. assumes no responsibility of liability for injury or death as a result of car crashes and / or air bag deployment. Arkon is not responsible for any damages caused to your car, your device, or yourself due to the installation or use of this pedestal mount.
The Mobile Mounting Specialists Consumer Hotline: USA (800) 841-0884 INTL (626) 254-9005 Monday - Friday 9 am - 5 pm, PST www.arkon.com Arcadia, CA 91006 USA Designed in USA | Made in Taiwan Copyright 2008 Arkon Resources, Inc.