MENU button

To switch the menu mode on/off.

UP button

Acts as button to move the highlighted area up to select the adjustment with OSD menu. Small screen which adjusted PIP mode moves up.

POWER button

Switches the power on/off. * If LED Power Indicator on the monitor is not glowing, then no controls will work.

PLUS button increase

Acts as (+) button to increase the adjustment with OSD menu. Small screen which adjusted PIP mode moves right.
Selects from input signal, [RGB1] (HDMI), [RGB2] (DVI-D), [RGB3] (D-SUB), [RGB4] (BNC), [RGB5] (CAT5), [DVD/HD] (YPbPr), [VIDEO<S>] and [VIDEO].
Turn to previous menu with OSD menu.

DOWN button

Acts as button to move the highlighted area down to select the adjustment with OSD menu. Small screen which adjusted PIP mode moves down.

PICTURE MODE button

Selects from picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA]. See page 21. HIGHBRIGHT: for moving image such as Video STANDARD: for images (Factory setting) sRGB: for text based images CINEMA: for movies.
To switch the mute function on/off.

VOLUME button

Increases or decreases the audio output level.

DISPLAY button

To switch the information OSD on/off. See page 22.

SET button

Acts as SET button with OSD menu.

MINUS button decrease

Acts as (-) button to decrease the adjustment with OSD menu. Small screen which adjusted PIP mode moves left.

AUTO SETUP button

To enter the auto setup menu. See page 28.

English-8

CAT5 Tx BOX
< Operating Range for the Remote Control >
Point the top of the remote control toward the LCD monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/23 ft. from the front of the LCD monitor's remote control sensor and at a horizontal and vertical angle of within 30 within a distance of about 3 m/10 ft.

USB (B type)

Connected to the USB connector (A type) of the computer. CAUTION: We have checked the operation of the USB connector by connecting it with our computers according to the USB standards. When the CAT TX5 BOX is combined with your computer system or USB hub system, check in advance that it operates properly.
EXTERNAL CONTROL IN (mini D-Sub 9 pin)
Connected to the RS-232C OUT connector of the computer. Note: RS-232C connection isnt necessary when the COM port number set by the USB driver is used. Make selection using the input select switch (USB/RS-232C), as necessary.
RGB IN (mini D-Sub 15 pin)
To input the analog RGB signals from other monitor.
To output the analog RGB signals from a computer.
Input select switch (USB/RS-232C)

Landscape

Clockwise 90

Counterclockwise 90

2. Connection of the CAT5 video connection function
There are two cases of connection. 1) Connection to one monitor
USB cable Computer CAT5 Tx BOX (supplied) CAT5 cable

MDT521S

Monitor
VGA (mini D-SUB 15-pin) cable (supplied)
1. Connect the USB connector of the supplied CAT5 Tx BOX and that of the computer using a commercially available USB cable. (When the USB driver isnt available, connect an RS-232C cable in addition to the USB cable. In this case, the RS-232C cable serves for supplying the power to the CAT5 Tx BOX.) See page 35.

English-12

2. Connect the D-SUB input connector of the CAT5 Tx BOX and the VGA (D-SUB) output connector of the computer using the signal cable (mini D-SUB 15-pin cable) supplied with the monitor. 3. Connect the modular connector of the CAT5 Tx BOX and the CAT5 (RGB5) IN connector of the monitor using a commercially available CAT5 cable. 2) Connection to multiple monitors
USB cable Computer CAT5 Tx BOX (supplied) Monitor CAT5 cable
3) CAT5 R-GAIN/G-GAIN/B-GAIN When the displayed image is dark, increase each value. When whites arent displayed as intended, adjust the R-GAIN and B-GAIN values. 4) CAT5 R-SKEW/G-SKEW/B-SKEW Adjust each value so that the color deviation in the displayed letters and graphic objects is minimized.
VGA (mini D-SUB 15-pin) cable (supplied) CAT5 cable Monitor
1. In addition to the connection made step 1) above, connect the CAT5 OUT connector of the rst monitor and the CAT5 (RGB5) IN connector of the second monitor using a commercially available CAT5 cable. 2. Connect the third and later monitors in the same way. You can connect up to 5 monitors. Allowable cable length Connection One monitor Multiple monitors Max. cable length/signal timing 150 m / 1920 x 1080 @60 Hz 200 m / 1920 x 1080 @60 Hz (Total length of the connected cables)
The lengths given above are based on the actual measurements using our standard signal source and the recommended cable as follows. Before installation, check the monitor operation in advance by connecting it with your computer and cables. Recommended cable: 8-pin modular connector, straight-through, shielded, Category 5 or 5e
3. Various settings involved in the CAT5 video connection
In the case of the CAT5 video connection, congure the following settings displayed on the OSD screen. (See page 29.) 1) CAT5 CABLE LENGTH Select the cable length, and the defaults of all the adjustment values are automatically determined. Select the length that is closest to the actual length of your cable.

English-13

2) CAT5 EQ Make adjustment so that blur and smear of the displayed letters and graphic objects are minimized.
How to Mount and Attach Options to the LCD Monitor
You can attach mounting accessories to the LCD monitor in one of the following two ways:
1. In the upright position
3. Ventilation Requirements for enclosure mounting
To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.
2. Lay the screen face down
Lay the protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. This device cannot be used or installed without the Tabletop Stand or other mounting accessory. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation. Failure to follow these recommendations could result in voiding your warranty. Use M8 screws (having a length 15 mm longer than the thickness of the mounting bracket) and tighten them securely. Prevent the screws from loosening using spring washers, etc. MITSUBISHI ELECTRIC recommends using mounting interface that comply with TV-GS and/or UL1678 standard in North America.

200 601

4. To avoid monitor from falling
When installing the monitor using the tabletop stands (optional), take measures to prevent the monitor from falling over in case of an earthquake or other disaster to lessen the probability of injury and damage resulting from fall. As shown in the gure, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor. (MDT521S: approx. 44 kg (with the optional stands)) When you use screw hooks (commercially available), ring screw hooks, not C-shaped screw hooks (with opening), are recommended.
400 mm Screw Holes Screw hook, etc. commercially available
Rope, etc. commercially available Clamper Screw

PICTURE RESET

Selecting Picture reset allows you to reset all OSD settings about PICTURE setting. Select Yes and press SET button to restore to factory preset data. Press EXIT button to cancel and then return to the previous menu.

English-25

AUTO BRIGHTNESS

SCREEN

H POSITION
Controls Horizontal Image position within the display area of the LCD. Press + button to move screen to right. Press - button to move screen to left.

V POSITION

Controls Vertical Image position within the display area of the LCD. Press + button to move screen to UP. Press - button to move screen to DOWN.
* : INPUT RGB3, 4, 5 only
Press + button to expand the width of the image on the screen the right. Press - button to narrow the width of the image on the screen the left.

CLOCK PHASE

Improves focus, clarity and image stability by increasing or decreasing this setting.

ZOOM MODE

You can select FULL, NORMAL and CUSTOM and REAL. (INPUT RGB1, 2, 3, 4, 5 only) You can also select FULL, NORMAL DYNAMIC and CUSTOM and REAL. (INPUT DVD/HD, VIDEO<S>, VIDEO only) Selecting DYNAMIC will make the screen display panoramic with the expansion of the middle and outside of the screen changed. (The upper and the bottom of the image will be cut by expansion.) Dynamic image is the same as FULL size image when HDTV signal is input. Selecting REAL image will be displayed 1 by 1 pixel.

CUSTOM ZOOM

CUSTOM ZOOM will be selected when you select CUSTOM on the screen ZOOM mode. ZOOM: expands the horizontal and the vertical size simultaneously. HZOOM: expands the horizontal size only. VZOOM: expands the vertical size only. H POSITION: moves to the right with + button. moves to the left with button. V POSITION: moves up with + button. moves down with button.

H RESOLUTION

* : INPUT RGB1, 2, 3, 4, 5 only
Adjusts the horizontal size by increasing or decreasing the setting. Press + button to expand the width of the image on the screen. Press - button to narrow the width of the image on the screen.

V RESOLUTION

Adjusts the vertical size by increasing or decreasing the setting. Press + button to expand the height of the image on the screen. Press - button to narrow the height of the image on the screen.

ROTATION

The OSD screen is rotated.

H FLIP

V FLIP

SCREEN RESET

Horizontally rotated

Vertically rotated

Selecting Screen reset allows you to reset all OSD settings from PICTURE setting. Select Yes and press SET button to restore the factory preset data. Press EXIT button to cancel and then return to the previous menu.

English-26

BALANCE
Adjust the balance of L/R volume. Press + button to move the stereo sound image to right. Sound of the left side will be small. Press - button to move the stereo sound image to left.

TREBLE

To accentuate or reduce the high frequency sound. Press + button to increase TREBLE sound. Press - button to decrease TREBLE sound.
To accentuate or reduce the low frequency sound. Press + button to increase BASS sound. Press - button to decrease BASS sound.

AUDIO RESET

Selecting Audio reset allows you to reset all OSD settings from AUDIO setting. Select YES and press SET button to restore the factory preset. Press EXIT button to cancel and then return to the previous menu.

PIP (PICTURE IN PICTURE)

Note: The PIP and POP modes do not function when the screen size is CUSTOM or REAL.

PIP SIZE

Selecting the size of picture inserted at the Picture-in-Picture (PIP) mode. Large, Middle and Small are available.

PIP AUDIO

Selecting the sound source in PIP mode. When selecting MAIN AUDIO, you will get the sound for the main picture and when selecting PIP AUDIO, you will get the sound for the picture instead.

PIP RESET

Selecting PIP Reset allows you to reset all OSD settings from PIP setting. Select Yes and press SET button to restore the factory preset data. Press EXIT button to cancel and then return to the previous menu.

English-27

CONFIGURATION 1

AUTO SETUP

Press SET button to automatically adjust screen size, horizontal position, vertical position, clock, clock phase, white level and black level. Press EXIT button to cancel execution AUTO SETUP and then will return to the previous menu.

AUTO ADJUST

Selecting the auto adjust ON/OFF. Selecting ON when changing the timing, the horizontal position, vertical position and clock-phase will adjust automatically.

POWER SAVE

Selecting RGB ON, the monitor will go to power management mode when RGB1, 2, 3, 4, 5 sync is lost. Selecting VIDEO ON, the monitor will go to power management mode after about 10 minutes delay from when DVD/HD, VIDEO<S> and VIDEO input signal is lost.

SERIAL CONTROL

Select the communication interface (RS232 or RS485) for the serial communication function. For connection of the signal cable, see page 35.

RS485 TERMINATION

Turn ON or OFF the termination resistance of the RS-485 interface. ON: Select this setting to use the monitor alone or to configure the monitor as the one at the end of the connection when more than one monitor is multi-connected. OFF: Select this setting to configure the monitor as other than the one at the end of the connection when more than one monitor is multi-connected.

OSD TURN OFF

The OSD control menu will stay on as long as it is use. In the OSD Turn Off submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 5 -120 seconds.

INFORMATION OSD

Selects the information OSD display or not. The information OSD will display when input signal or source change or warning message like as no-signal or out-of range. A time between 1 to 10 seconds is available.

OFF TIMER

To select OFF TIMER mode ON/OFF. In the OFF TIMER menu, you can preset the monitor to automatically power down. A time between 1 to 24 hours is available. When the OFF TIMER is set, the SCHEDULE (see page 31) settings will be disabled.

OSD H POSITION

Adjusts the horizontal position of the OSD menu.

OSD V POSITION

Adjusts the vertical position of the OSD menu.

MONITOR INFORMATION

Indicates the model and serial number of your monitor.

English-29

ADVANCED OPTION

INPUT RESOLUTION

Selects to decision of input signal about below timings, 1024x768, 1280x768 and 1360x768. AUTO: Determines the resolution automatically. 1024x768: Determines the resolution as 1024x768 1280x768: Determines the resolution as 1280x768 1360x768: Determines the resolution as 1360x768 The setting you select becomes effective when POWER is turned OFF and ON again.

BLACK LEVEL EXPANSION

Selects a level of black expansion from OFF, MIDDLE and HIGH. In case of go under the black cut-off level, please adjust the Black level in moderation on OSD menu.

SCAN MODE

Changes the display area of the image. OVERSCAN: Set to display area about 95% UNDERSCAN: Set to display area about 100%

SCAN CONVERSION

Selects IP (Interlace to Progressive) converter function. PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use this setting. INTERLACE*: Disable the IP function. *NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.

FILM MODE

Selects Film mode function. AUTO: Enable the Film mode function. This mode is better suited for movies, which is converted 24 Frames/sec source to DVD Video. We recommend to select PROGRESSIVE in SCAN CONVERSION. OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.

IR CONTROL

Selects the operation mode of the wireless remote controller when multiple MDT521S monitors are connected via RS-232C. The item in this menu will become effective by pressing SET button on the selected item. NORMAL: The monitor will be controlled normally by wireless remote controller. PRIMARY: The first MDT521S monitor of those multi-connected via RS-232C is designated as PRIMARY. SECONDARY: MDT521S monitors other than the first one multi-connected via RS-232C are designated as SECONDARY. LOCK: Disable the monitor control by infrared wireless remote controller. Keep pressing DISPLAY button during 5 sec or more, this setting will return to NORMAL.

TILING

TILING demonstrates multiple screens. This feature provides a single large screen using up to 25 monitors. It will be able to divide up to 5 each H and V. This requires you to feed the PC output into each of the monitors through a distributor. H MONITORS: Select number of horizontal divide. V MONITORS: Select number of vertical divide. POSITION: Select a position to expand the screen. FRAME COMP.: Works in tandem with TILING to compensate for the width of the tile bezels in order to accurately display the image. ENABLE: Select YES, the monitor will expand the selected position. PIP and STILL will be disabled when TILING is activated.

English-30

Information of status for COOLING FAN, BRIGHTNESS and TEMPERATURE. COOLING FAN comes to run when inside temperature is over a guaranteed limit. In this case warning is displayed on the screen.

POWER ON DELAY

Adjusts the delay time from standby to power on mode. POWER ON DELAY time is selectable from 0-50 seconds.

DATE AND TIME

Adjusts the current date and time for internal clock. You should set this function when you use SCHEDULE.

SCHEDULE

Programs the monitor's working schedule. Schedule the power on and power off with hour and a day of the week. Also sets the input port. This OSD can't remove except EXIT. (see HOW TO SETUP SCHEDULE on page 32.)

HDMI INPUT MODE

Select HDMI-PC when PC or other computer equipment is connected via HDMI. Select HDMI-HD when DVD player, which has HDMI output, is connected via HDMI.

DVI INPUT MODE

Select DVI-PC when PC or other computer equipment is connected via DVI-D. Select DVI-HD when DVD player, which has HDMI output, is connected via DVI-D.

MONITOR ID

ID numbers for remote control are assigned to MDT521S monitors that are multi-connected via RS-232C. ID numbers 1 to 26 are selectable.

DDC/CI

Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.

SYNC TYPE

* : INPUT RGB3, 4 only
Select 0.3V for 0.3 Composite Sync. Select TTL for TTL Sync.

ADVANCED OPTION RESET

Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION settings, except for DATE AND TIME, SCHEDULE, HDMI INPUT MODE, DVI INPUT MODE, MONITOR ID, and DDC/CI. Select YES and press SET button to restore the factory preset data. Press EXIT button to cancel and then return the previous menu.

English-31

HEAT STATUS
< IMAGE PERSISTENCE >
Please be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when residual or ghost image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. As with all personal display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Please set POWER SAVE, SCREEN SAVER, DATE AND TIME and SCHEDULE functions to further reduce the risk of Image persistence.

English-32

< PIP, POP and SIDE BY SIDE >
The following table shows the combination of signal inputs under which the PIP and POP modes function. These modes do not function, however, when the screen size is CUSTOM or REAL. MAIN SUB RGB1 (HDMI) RGB2 (DVI-D) RGB3 (D-SUB) RGB4 (BNC) RGB5 (CAT5) DVD/HD (YPbPr) VIDEO<S> VIDEO : Supported : Not supported
RGB1 (HDMI) RGB2 (DVI-D) RGB3 (D-SUB) RGB4 (BNC) RGB5 (CAT5) DVD/HD (YPbPr) VIDEO<S> VIDEO Press the PIP ON/OFF buttons on the remote control to change between PIP, POP and SIDE BY SIDE mode as shown in the diagram below. SIDE BY SIDE SIDE BY SIDE PIP POP ASPECT FULL
PIP, POP mode resolution (Reference) PIP SIZE SMALL MIDDLE LARGE POP SIZE : 450 dots X 338 dots : 675 dots X 450 dots : 900 dots X 675 dots : 450 dots X 338 dots
< Supplemental information of the auto brightness function >
To control multiple monitors collectively In such a case where the tiling function is used, you can control the auto brightness function by sharing the detection result of the brightness sensor of a certain monitor among the connected monitors. 1. Multi-connect the monitors using RS-232C or CAT5 cables as shown by the example below. Monitor ID = 9 (Slave) Monitor ID = 8 (Slave) Monitor ID = 7 (Slave)
Monitor ID = 6 (Slave) Monitor ID = 3 (Slave)
Monitor ID = 5 (Slave) Monitor ID = 2 (Slave)
Monitor ID = 4 (Slave) Monitor ID = 1 (Master)
Master: Monitor configured as Master that detects the outside light (Monitor ID is 1.) Slave: Monitor controlled by the Master monitor (Monitor ID is other than 1.)
2. Assign a monitor ID to each multi-connected MDT521S using MONITOR ID. Monitor ID is selectable from 1 to 26. The monitor ID of the Master monitor should be 1 and those of the Slave monitors should be other than 1. You are recommended to assign IDs to the monitors consecutively from 1, 2, 3, and on. 3. Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows. Master monitor Slave monitors AUTO BRIGHTNESS LOCAL REMOTE CONTROL PRIMARY SECONDARY

English-33

To use a computer to control the monitors When using a computer to control the monitors, you must prepare an application software program for control by yourself. 1. Connect the RS-232C IN connector of the Master monitor shown above and the RS-232C connector of the computer using an RS-232C cable. Or, using a CAT5 cable, connect the RS-232C connector of the computer to the CAT5 IN connector of the Master monitor via the CAT5-TX box. 2. Assign a monitor ID to each multi-connected MDT521S using MONITOR ID. (See step 2 above.) 3. Set AUTO BRIGHTNESS on the OSD screen (PICTURE) as follows. Master monitor Slave monitors or t e se o AUTO BRIGHTNESS REMOTE REMOTE CONTROL SECONDARY SECONDARY

omm ni ation omman s

onta t o r ealer
< Remote control numbering function >
B onne tin m lti le MDT S monitors sin RS C a les o an ontr ol an one monitor or all t e monitors one remote ontroller Assi n ar itrar ID n m er to ea o m lti onne te MDT S monitors sin MONITOR ID ID n m ers to are sele ta le It is re ommen e to assi n se ential ID n m ers rom an T e remote ontrol mo e o t e rst MDT S monitor is set to RIMAR Y an t ose o t e ot er monitors are set to SECONDARY en o ire t t e remote ontroller at t e remote ontrol si nal sensor o t e RIMARY monitor an r ess t e DIS LAY tton on t e remote ontroller t e ID sele tion OSD a ears at t e er le t o t e s reen

ID:1 ID No. :2

ID number of the currently viewed monitor Select the ID number of the monitor you want to control using the +/- button on the remote controller. The ID of the monitor you want to control is displayed at the upper left of its screen. By selecting ALL, you can control all the multi-connected monitors.
Dire t t e remote ontroller at t e remote ontrol si nal sensor o t e RIMARY monitor OSD a ears on t e monitor avin t e ID n m er o sele te NOTE: en t e ID sele tion OSD is ein is la e on t e RIMAR Y monitor ress t e DIS LAY a ain to an el t e ID sele tion OSD an t en ontrol t e monitor o sele te
tton on t e remote ontroller
NOTE: I o set t e remote ontrol mo e ron l an remote ontrol o er ation e omes navaila le ress an tton on t e ontrol anel o t e monitor to is la t e OSD s r een an an e t e remote ontrol mo e sin AD ANCED O TION B ressin an ol in o n t e DIS LAY tton on t e remote ontrol or se on s or lon er t e remote ontrol mo e is initiali e to NORMAL

English-34

Controlling the LCD monitor via RS-232C/RS-485 Remote Control
This LCD monitor can be controlled by the computer connected by an RS-232C cable or a CAT5 cable via the supplied CAT5 Tx BOX. Functions that can be controlled by a personal computer are: Power ON or OFF Switching between input signals Connection Connection by RS-232C (For RS-232C cable, the reverse type cable should be used.)

PC RS-232C cable

To RS-232C IN

To RS-232C OUT

RS-232C cable
Connection by CAT5 RS-485 (For CAT5 cable, the straight type cable should be used)

Type A Type B CAT5 Tx BOX (supplied) Monitor Monitor
USB cable PC To RS-232C IN To CAT5 OUT

To CAT5 RGB5 IN

To CAT5 OUT

CAT5 cable

This connection isnt necessary when the USB COM port is used.
NOTE: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your dealer for details. 1) Interface PROTOCOL BAUD RATE DATA LENGTH PARITY BIT STOP BIT FLOW CONTROL RS-232C/RS-485 (CAT5) 9600 [bps] 8 [bits] NONE 1 [bits] NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control. 2) Control command diagram The command is structured by the address code, function code, data code and end code. The length of the command is different for each function. Address code HEX ASCII 30h 30h Function code Function Function Data code Data Data End code 0Dh
[Address code] [Function code] [Data code] [End code]
30h 30h (In ASCII code, 0 0) xed. A code of each xed control move. A code of each xed control data (number) and not always indicated. 0Dh (In ASCII code, ) xed.

English-35

3) Control sequence (1) The command from a computer to the LCD monitor will be sent in 600 ms. (2) The LCD monitor will send a return command 600 ms* after it has received and encoded. If the command isnt received correctly, the LCD monitor will not send the return command. (3) The personal computer checks the command and conrms if the command, which has been sent, has been executed or not. (4) This LCD monitor sends various codes other than return code. When having a control sequence by RS-232C, reject other codes from personal computers side. * : The sending time of return command may delay depending on the condition (during changing of the input signal, etc.). Example: Turn the power ON ( is for ASCII code) Sending commands from the PC 21 0D ! Status code from LCD monitor Meaning Command for POWER ON Command received (Command echoed back)

21 0D !

4) Operation commands The operation commands execute the basic operation setting of this LCD monitor. It may not operate when changing the signal: Operation POWER ON POWER OFF INPUT RGB 1 INPUT RGB 2 INPUT RGB 3 INPUT RGB 4 INPUT RGB 5 INPUT VIDEO INPUT DVD/HD INPUT S-VIDEO* ASCII ! " _r1 _r2 _r3 _r4 _r5 _v1 _v2 _v3 HEX 21h 22h 5Fh 72h 5Fh 72h 5Fh 72h 5Fh 72h 5Fh 72h 5Fh 76h 5Fh 76h 5Fh 76h POWER OFF command should be operated over 1 minute after the power is turned on. POWER ON command should be operated over 1 minute after the power is turned off. * S-VIDEO is SEPARATE only
31h 32h 33h 34h 35h 31h 32h 33h
5) Read command Host computer sends the command without Data-code to monitor. After receiving this command, the monitor returns the command with Data-code of current status to host computer. Example: When Host computer ask Power status of monitor, the status of monitor is powered-on. Detail of command Command from computer Command from Monitor Ask about the power status of monitor 0D '0''0''v''P'[enter] 31 0D '0''0''v''P''1'[enter] Monitor is powered-on. Structure of the Read-command Function vP vP vI vI vI vI vI vI vI vI vM vM tc1 tc2 ASCII Data (Receive) r1 r2 r3 r4 r5 v1 v2 v3 p1 p2 (ex.) +25 (ex.) +31 Function 76 4D 76 4D HEX Data (Receive) 2B 35 2B 31

Picture mode Temperature of internal monitor
ON OFF (stand by) RGB-1 (HDMI) RGB-2 (DVI-D) RGB-3 (D-SUB) RGB-4 (BNC) RGB-5 (CAT5) Video DVD/HD S-VIDEO HIGHBRIGHT STANDARD resolution Around 1 C Main board Around resolution Power PCB 1 C

English-36

Features

Reduced Footprint:

Color Control Systems:
Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to a variety of standards.

sRGB Color Control:

A new optimized color management standard which allows for color matching on computer displays and other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls:
Allow you to quickly and easily adjust all elements of your screen image via simple to use on-screen menus.

Plug and Play:

The Microsoft solution with the Windows 95/98/Me/2000/XP operating system and Windows Vista facilitates setup and installation by allowing the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically optimizing display performance.
Intelligent Power Manager System:
Provides innovative power-saving methods that allow the monitor to shift to a lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and lowering the air conditioning costs of the workplace.
Multiple Frequency Technology:
Automatically adjusts monitor to the display cards scanning frequency, thus displaying the resolution required.

FullScan Capability:

Allows you to use the entire screen area in most resolutions, signicantly expanding image size.

Wall Mounting Interface:

Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. MITSUBISHI ELECTRIC recommends using mounting interface that comply with TV-GS and/or UL1678 standard in North America.
TILING, Frame compensation:
Demonstrates multiple screens with an accurate image and compensates for the bezel width.
Expands the image individually for horizontal and vertical direction.

Self-diagnosis:

When an internal error should occur, a failure state will be indicated.
CAT5 Long Cable Compensation:
CAT5 long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.

English-37

Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The monitors small footprint and low weight allow it to be moved or transported easily from one location to another.

RED LED on monitor is blinking
A certain failure might have occurred, please contact your nearest authorized MITSUBISHI ELECTRIC service facility.
Display image is not sized properly
Use the OSD Image Adjust controls to increase or decrease the coarse adjustment. Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.)
Selected resolution is not displayed properly
Use OSD Display Mode to enter Information menu and conrm that the appropriate resolution has been selected. If not, select corresponding option.

English-38

No Sound
Check to see if speaker cable is properly connected. Check to see if mute is activated. Check to see if volume is set at minimum.
Remote Control is not available
Check the Remote Controls batteries status. Check if batteries are inserted correctly. Check if the Remote Control is pointing at the monitors remote sensor.
SCHEDULE/OFF TIMER function is not working properly
The SCHEDULE function will be disabled when the OFF TIMER is set. If the OFF TIMER function is enable and the power to the LCD monitor is turned off if the power supply is interrupted unexpectedly, then the OFF TIMER will be reset.

Stripe Noise

Either light vertical or horizontal stripes may appear, depending on the specic display pattern. This is no product fault or degradation.
NO SIGNAL is displayed on the screen
Image may not be displayed right after HDCP device is connected.

English-39

Specications

Specications (MDT521S)

Product Specifications LCD Module Diagonal: Pixel Pitch: Resolution: Color: Brightness: Contrast Ratio: Response time: View Angle: Horizontal: Vertical: Analog Input 52" / 132.2 cm 0.600 mm 1920 x 1080 dots (2070000 dots) Over 16 million colors (depending on video card used) 700 cd/m2 (typ.) 2000:ms (G to G) Up and Down 178, Left and Right 178 @CR>10 15.625 / 15.734, 31.5 - 91.1 kHz 50.0 / 58.0 - 85.0 Hz 13.5 -165.0 MHz 1152.0 x 648.0 mm / 45.4 x 25.5 inches Digital Input
Frequency Pixel Clock Viewable Size Input Signal PC-Input:

25.0 -165.0 MHz

VIDEO Input:
AUDIO Input: CAT5: RS-232C: Output Signal PC-Output:
TMDS Video: Analog RGB Video: 0.7 Vp-p Input impedance 75 ohm Sync: Separate HV sync: TTL level (Pos./Neg.), Sync-on-green, Composite Sync (0.3Vp-p) Input Impedance 2.2K ohm HDMI, DVI-D Input-terminal: BNC (R,G,B,H,V), 15 Pin Mini D-sub Composite: 1.0 Vp-p Input impedance 75ohm BNC and RCA-PINJACK-INPUT Y/C Y: 1 Vp-p C: 0.286 Vp-p Input Impedance 75 ohm S-TERMINAL-INPUT Component: 1.0 / 0.7 Vp-p Input Impedance 75 ohm BNC-INPUT RCA PIN-JACK L/R INPUT x 2, STEREO Mini Jack INPUT x 1 In: Modular connector 8 pin In: 9 Pin Mini D-sub

PRESENTATION PRODUCTS

MITSUBISHI ELECTRIC

MDT521S

52 LCD Monitor
Slim eye-catching bezel design Advanced high-definition digital signage display Full 1920 x 1080 native resolution Built-in CAT5 transmitter and receiver Front and rear ambient light sensors

Leading the evolution of

High-Definition

digital signage

www.mitsubishi-presentations.com

888.307.0349

bezel respon se
Cla ss VIEWABLE im age SIZE O rie nta tio n BRIGHTNESS/LUMENS pix el p itch CONTRAST RATIO DIMENSIONS (W x H x D in.)
(W ithout stand and speak ers)
52 (Diagonal) LCD Monitor

45.4 x 25.5

Landscape / Portrait / Face Up

700 cd/m2

0.600 mm

2000:1

47.3 x 27.5 x 4.8 WEIGHT

88 lbs. (Net)

width time viewing ang le

8 ms (gray to gray)

Horizontal and vertical: 178O

Optional Stand: ST-521S

I NPUTS and

video / outp

Audio uts
multiple standard input and output connectors
mini D-Sub 15 pin In/Out, HDMI, DVI-D, CAT5 In/Out, BNC (R,G,B,H,V) In/out, S-Video, Composite (BNC, RCA), Audio LR (RCA), Audio Stereo mini jack speak er

outp ut

RGB 1 IN (HDMI) RGB 2 in (DVI-D) ternal S peak er T erminal
External speaker jack Con
RGB 3 IN (mini D-Sub 15 pin)
Slot for optional CAT5 input/output connectors

ideo In/O ut

ideo IN ideo OUT ideo IN connector (BNC) connector (BNC and RCA) V S-V
RGB 4 In/ DVD/HD In (BNC) AC IN connector Ex A udio out

trol inp ut/

outp ut POWER CONSUMPTION (W ithout speak ers)
RS232C (mini D-Sub 9 In/Out)

(modular connector 8pin)

(mini D-Sub 9 pin)

ternal C

ontrol
RGB out (mini D-Sub 15 pin)
connector (Mini DIN 4 pin) 7

udio IN 1,2,3

stim a
ted Back lig ht Life AUDIO SPE AKER Ta ble Stand

Up to 50,000 hours*

Rear Connector Panel

Optional: SP-521S

Optional: ST-521S
Wa ll M ount com pata bilit y

In In In

Optional: CTM-MS2 WARR ANTY

Side Connector Panel

3-years parts and labor, Express Replacement Assistance, toll-free 24x7 technical support
*Results may vary depending on usage and operating environment
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. Presentation Products Division Toll Free: Email: ppdinfo@mdea.com www.mitsubishi-presentations.com Canada Mitsubishi Electric Sales Canada Inc. Information Technologies Group Phone: 905.475.7728 www.mitsubishielectric.ca

LITMDT521S