47507MCZ-Rev1-PumpEspresso

25/9/06

4:20 pm

Page 1

Pump espresso coffee maker
Please read and keep these instructions

erpac kvovar na espreso

Pette si tyto pokyny a uschovejte je

47507MCZ 07/06

www.morphyrichards.com

Page 2

STEAM OFF

COFFEE

B3 E B4 L S

Page 3
Important safety instructions
The use of any electrical appliance requires the following common sense safety rules. Primarily there is danger of injury or death and secondly the danger of damage to the appliance. These are indicated in the text by the following two conventions: WARNING: Danger to the person! IMPORTANT: Damage to the appliance! In addition we offer the following safety advice.
Milk should not be reheated, only heat it when required.

Children

Children do not understand the dangers associated with operating electrical appliances. Never allow children to use this appliance.

Treating scalds

Run cold water over the affected area immediately. Do not stop to remove clothing, get medical help quickly.

Product safety

WARNING: Do not immerse the coffee maker itself in water and always ensure the electrical connections are kept dry. Never use warm or hot water to fill the water reservoir. Do not use the glass jug in a microwave. Do not overfill the water reservoir. Do not fill above the capacity of the water level gauge marked on the jug. Operate the appliance only with the drip tray in place.

Location

Ensure the coffee maker is used on a firm, flat surface. Do not use the coffee maker outdoors or in a bathroom. Do not place the coffee maker on a highly polished wooden surface as damage may occur to the surface. Do not place the coffee maker on or near hot surfaces such as a hot plate or radiant rings or near a naked flame. IMPORTANT: Do not place the coffee maker onto a metal tray or metal surface whilst in use.
Other safety considerations
Disconnect the coffee maker from the mains supply when filling, cleaning or not in use. Keep the outside of the coffee maker area clean and dry at all times. The use of attachments or tools not recommended or sold by Morphy Richards may cause fire, electric shock or injury. Do not use abrasive cleaners on the outside of the coffee maker, they may scratch the surface. Clean only with a soft damp cloth. Do not use the coffee maker for anything other than its intended purpose. Do not adjust strength control whilst the coffee maker is brewing. 3

Personal safety

WARNING: Do not touch hot surfaces. Always use handles or knobs. WARNING: Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Ensure the lid of the glass jug is securely in place before pouring. Take care to pour hot coffee slowly and carefully without tipping the glass jug too fast. Do not touch metal parts until the appliance has cooled.

Page 4

Do not place the glass jug on the hot plate unless the lid is in position. Do not lift the coffee maker by gripping the water reservoir. Hold the body of the coffee maker.

Before first use

1 Remove all the packaging and retain for future reference. Before using your coffee maker for the first time or if you have not used it for some time, it is important to rinse the coffee maker by running water through. Follow the procedure for making espresso coffee, without coffee in the filter holder.

Electrical requirements

Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. WARNING: This appliance must be earthed.

Display symbols

B Flashing: warming up B Ready to make coffee or making coffee (lever down) B Flashing: Warming up to make 3 steam or hot water B Ready to make steam 4 or making steam (lever up) B Ready to make hot water 5 (lever up)
MAKING ESPRESSO COFFEE Filling the water reservoir
1 Remove the water reservoir by sliding the water tank upwards using the handle C. Open the lid of the water reservoir by pulling up and sliding backwards. Fill the water reservoir using cold tap water, 1.7 litres maximum D. IMPORTANT: Do not overfill or carry with the handle when full. Replace the water reservoir by sliding it back into place E.

Features

1.7L removable water reservoir Power light Hot water/steam selector switch On/off switch Brewing head Filter lock Filter holder Drip tray water level indicator Non slip rubber feet 1 cup filter 2 cup filter Hard pod filter Measuring spoon Compactor Removable drip tray Froth attachment Steam nozzle Coffee or steam lever Display Warming plate

Using with ground coffee

Ensure the coffee/steam lever is in the off position. 1 Plug the coffee maker into the power outlet. Switch the coffee maker on by pressing the on/off switch. The blue power light and the display will illuminate. Pre-heat your coffee cups by placing them upside down on the warming plate. This coffee maker is designed for use with espresso or cappuccino cups only. The coffee will be much weaker if larger cups are used.

Page 5

Select the required filter for 1 cup or for 2 cups and place in the filter holder F. The filters have many inlet holes and a single outlet hole. Using your measuring spoon supplied, place one or two measures of ground coffee into the filter, depending on filter choice. Use the compactor on the other end of the measuring spoon to tamp down the coffee G. Do not overfill the filter. Wipe around the edge of the filter to remove any coffee grounds. Place the filter holder on the brewing head with the handle to the left H. With the filter holder flat against the brewing head, turn the handle to the right as far as it will go I. Place one or two pre-heated cups below the holes in the filter holder J or K. When the coffee maker is at the correct temperature the coffee cup symbol will be displayed.
Using with the coffee pods
1 Select the pod filter and place in the filter holder M.
Remove the espresso pod from the packaging N. Place the coffee pod in the filter with the flap placed inside the filter O. Place the filter holder on the brewing head with the handle to the left H. With the filter holder flat against the brewing head, turn the handle to the right as far as it will go I. Place a pre-heated cup below the holes in the filter holder J. One coffee pod has the measured amount of coffee for one single espresso. When the coffee maker is at the correct temperature the coffee cup symbol will be displayed. Move the lever down to the coffee setting. The coffee maker makes a pumping noise, this is normal. Once the cup is nearly filled to the desired level, move the lever back to the off position. Water will filter through for approximately 8 seconds after the coffee maker has been turned off. Remove by turning the filter holder slowly to the left. To remove the pod from the filter, push the filter lock forward over the edge of the filter and turn the filter holder upside down L.

Move the coffee or steam lever down to the coffee setting. You will hear the coffee maker make a pumping noise, this is normal. Once the cups are filled to the desired level, pull the lever to the off position. Water will still filter through for approximately 8 seconds after the coffee maker has been turned off.
10 Carefully remove the filter holder by turning the handle slowly to the left. 11 To remove the used coffee grounds from the filter, push the filter lock forward over the edge of the filter and turn the filter holder upside down. Gently tap out the coffee L. 12 Once the coffee cup symbol shows, your coffee maker is ready to make the next espresso. It is normal for the symbols on the display to cycle on and off during the water heat-up process.
10 Once the coffee cup symbol shows, your coffee maker is ready to make the next espresso. It is normal for the symbols on the display to cycle on and off during the water heat-up process.

Page 6

Steam function
The froth attachment makes it easy to produce frothy milk for cappuccino. Ensure the coffee/steam lever is in the off position. 1 Before using the steam nozzle, remove the filter holder. Attach the froth attachment to the end of the steam nozzle P.

Frothing tips

For best results use fresh, cold milk from the refrigerator. Skimmed milk or fat reduced milk will make frothing easier.

Hot water drinks

You may want to top up your espresso with hot water for a longer drink or to make other hot water drinks such as tea or instant soups using the steam nozzle.
For the froth enhancing attachment to work properly it must be pushed firmly onto the steam nozzle. Fill the water reservoir with cold tap water. Swing the steam nozzle with the froth attachment to the side of the coffee maker. Press the hot water/steam selector switch , the steam symbol will flash. When the coffee maker is ready to make steam it stays on. Pour cold milk into a suitable jug. Use approximately 100ml for each cappuccino. For best results we recommend to use refrigerated milk and a stainless steel jug that is well chilled. Hold the jug under the steam nozzle so that the head of the froth attachment is immersed in milk and push the lever up to the steam setting Q. The coffee maker makes a pumping noise, this is normal. Do not allow the tip of the nozzle to touch the bottom of the jug because this could obstruct the passage of steam. Once the froth has been produced push the lever down to the off position and remove the jug. Do not be alarmed by the escaping steam from the base. The milk is ready as soon as it forms a soft, thick layer of foam on the top. If the milk starts to make large popping bubbles, the milk has boiled and it will not froth. If this happens replace with chilled milk. Do not boil the milk. 1

If the machine has been in use:
Take care when removing the froth attachment from the steam nozzle, it may be extremely hot. Ensure the water reservoir is filled with cold tap water. Swing the steam nozzle to the side of the coffee maker. Take extreme care when handling the steam nozzle it may be extremely hot.
If the machine has not been in use:
4 Ensure the unit is cold before removing the froth attachment from the steam nozzle. Ensure the water reservoir is filled with cold tap water. Swing the steam nozzle to the side of the coffee maker. Switch the unit on by pressing the on/off switch. The blue power light and display will illuminate.
Choose a finely ground espresso coffee to use with this coffee maker. Avoid blends that are very powdery. When the coffee is too finely ground it may block the filter. For best results cups should be warmed. Cups should be placed upside down on the warming plate. Please note that this may take up to 20 minutes depending upon the type of cup used.

Page 7

To make hotter coffee the coffee maker can be preheated. Follow the procedure for making espresso coffee, without coffee in the filter holder.
IMPORTANT: No parts are suitable for cleaning in a dishwasher. 3 The filters, filter holder and water reservoir should be washed after each use by rinsing them under water. To assist in keeping the filters clean we recommend you periodically run the coffee maker with the filter in place, without coffee, using water only. Should the holes in the filters become blocked with coffee granules use a fine bristled brush. When your coffee maker is not being used, we recommend that you do not leave the filter holder attached to the coffee maker as this will reduce the life of the gasket.

Descaling

It is important to descale as the performance of your coffee maker may be impaired by limescale and other impurities in the water supply. If you live in a hard water area, we recommend that your coffee maker is descaled at regular intervals, e.g. every 2-3 months. In areas of moderately hard water you should descale every 6 months. If the water filters through more slowly than usual, it is a sign that descaling is necessary. We recommend you use proprietary liquid descaler which is especially made for coffee makers and plastic kettles. Follow the instructions on the bottle or sachet, and then operate the coffee maker with just water 3 times before making coffee. Do not use kettle descaler unless the packet specifically states it it suitable for coffee makers. The permanent filters should not be used during descaling. 3

Drip tray

1 The water level indicator appears through the grid to indicate that the drip tray is full. Remove the grid of the drip tray by placing fingers in the two holes in the centre of the drip tray and lift off R. This must be done regularly or as soon as the red water level indicator appears through the grid. Lift the front of the drip tray up and slide it out S. Lift off the plastic lining of the drip tray T. Clean the drip tray and its grid with water and a little washing up liquid, rinse and dry. Reverse the procedure to reassemble. Ensure that when you are replacing the drip tray that the plastic lining is in the correct position.

Cleaning and maintenance

You must clean the steam nozzle and froth attachment immediately after each use. 1 Wipe the steam nozzle, warming plate and exterior with a clean, damp cloth. Do not use any abrasives or metal scourers as this will damage the finish on the coffee maker. Briefly push the lever to the steam setting to clear any remaining milk out of the steam nozzle. WARNING: Steam from the nozzle is extremely hot and can scald. 2 Place the froth attachment under warm running water to remove excess milk.

Page 8

Your two-year guarantee
It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product.
To qualify for the 2-year guarantee the appliance must have been used according to the manufacturers instructions. For example, appliances must have been descaled and filters must have been kept clean as instructed. Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturers recommendations or where the fault has been caused by power surges or damage caused in transit. The appliance has been used on a voltage supply other than that stamped on the products. Repairs have been attempted by persons other than our service staff (or authorised dealer). Where the appliance has been used for hire purposes or non domestic use. Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. The guarantee excludes consumables such as bags, filters and glass carafes. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer.

Model no.

Serial no.
All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. If the fault develops after 28 days and within 24 months of original purchase, you should contact Morphy Richards quoting Model number and Serial number on the product, or write to Morphy Richards at the address shown. You will be asked to return the product (in secure, adequate packaging) to the address below along with a copy of proof of purchase. Subject to the exclusions set out below (1-6) the faulty appliance will then be repaired or replaced and dispatched usually within 7 working days of receipt. If for any reason this item is replaced during the 2-year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.

Page 9

Page 10

Page 11

Dleit bezpenostn pokyny
Pouvn jakhokoliv elektrickho spotebie vyaduje dodrovn bezpenostnch pravidel diktovanch zdravm rozumem. Za prv hroz riziko razu nebo usmrcen a za druh riziko ato pokozen spotebie. T rizika jsou v textu oznaovna dvma nsledujcmi zpsoby: VAROVN: Hroz nebezpe osobm! DLEIT: Pokozen spotebie! Navc nabzme nsledujc bezpenostn doporuen.
Nedotkejte se kovovch soust, dokud spotebi nevychladne. Mlko se nesm znovu ohvat, ohejte ho teprve tehdy, kdy je teba.
Dti nechpou nebezpe souvisejc s provozovnm elektrickch spotebi. Nenechvejte je pouvat tento spotebi.

Lba opaenin

Zasaen msto ihned vlote pod tekouc studenou vodu. Nezdrujte se sundvnm odvu, ihned vyhledejte lkaskou pomoc.
Ujistte se, e kvovar je pouvn na pevnm, rovnm povrchu. Nepouvejte kvovar venku nebo v koupeln. Nepokldejte kvovar na letn devn nbytek s vysokm leskem, protoe by mohl pokodit povrch. Nepokldejte kvovar na hork povrchy nebo do jejich blzkosti, napklad na plotnky nebo slav zdroje tepla, ani do blzkosti otevenho plamene. DLEIT: Bhem pouvn nepokldejte kvovar na kovov tc nebo kovov povrch.

Bezpenost vrobku

VAROVN: Neponoujte kvovar do vody a vdy zajistte, aby byly elektrick spoje such. Ndr na vodu nikdy neplte teplou nebo horkou vodou. Nevkldejte sklennou konvici do mikrovlnn trouby. Nepeplujte ndr na vodu. Nenalvejte vodu ve, ne ukazuje znaka hladiny na konvici. Pouvejte spotebi pouze s instalovanou odkapvac miskou.