USE THE HT820

Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions.

Your Headphones' Battery

CHARGE
Start Here > > >
HT820 Bluetooth Stereo Headphones
You can use your HT820 headphones simultaneously with a Bluetooth A2DP enabled audio device and your Bluetooth cell phones! Listen to music, hear a beep, and transfer to take the call on the headphones. Hang up the call with a push of a button and your music automically continues playing.
Any Bluetooth Enabled Audio Device* HT820
Before using your HT820 for the first time, charge the headphones for 2 hours:
Charger Insert Charger Here Music Button Indicator Light (Right Side)
Before you can use your headphones with a Bluetooth enabled product, you must pair it with that product. To pair:
Your Headphones & Audio Device Your headphones are successfully paired with a device and ready to use when the blue indicator lights changes from steadily lit, flashes rapidly, and then slowly flashes. To confirm they are operating properly:

TEST AND USE

1 Make sure your headphones are turned off
1 Plug the Motorola charger into the
(see Turning On and Off ) and press and hold the left side Call m button for 6 seconds until the indicator light turns on and remains steadily lit.
Call Button with Indicator Light (Left Side)
1 Place the headphones on your head. See
Wear the Headphones in this guide.

Bluetooth Enabled Phone

headphones. The indicator light turns on when the battery is charging. When the headphones' battery is fully charged, the indicator light turns off.
2 Start playing music on the audio device. If
your headphones are successfully paired, you will hear music in the headphones.
Note: You may need to wait several seconds before hearing music in the headphones while the devices connect.
2 Disconnect the charger.
Note: Headphones do not function while charging.
2 Next, put your Bluetooth Enabled audio

Ready to make it work?

device in pairing mode so the devices can "talk" to each other. For details about putting Bluetooth Enabled devices in pairing mode, refer to the device's User's Guide for directions.
- Charge your Headphones for 2 Hours (CHARGE) - Pair headphones & audio device (PAIR) - Pair phone & headphones (back side of this guide) - Listen to music and take calls!
*The Bluetooth Enabled Audio Device must be A2DP compatible
You can also use a Motorola Original Vehicle Power Adapter to charge your headphones while in your vehicle. A fully charged battery provides approximately: 14 hrs of music listening, 17 hrs of talk time, or 500 hrs of standby time.
See Music Controls for information about using the HT820 volume and playback controls. After successfully pairing, you do not need to repeat these initial setup steps each time you use the headphones. Just power on both devices and they automatically connect.
Note: To pair the headphones with your phone, see "Pair with your Phone," on the reverse side of this guide.
Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 USA www.hellomoto.com 1-877-MOTOBLU 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada)

TURN ON AND OFF

To turn your headphones on, press and hold the left side Call m button until the indicator light flashes 3 times (about 3 seconds). Then, release the button. To turn your headphones off, press and hold the left side Call m button until the indicator light flashes rapidly and then turns off (about 3 seconds). To conserve battery power, turn off the headphones when you will not be using it.

CONNECT SIMULTANEOUSLY

Simultaneous connect your headphones with a music device AND your phone! Pair the headphones to the music device (PAIR). Then pair the headset with your phone (backside of guide). Power your headphones off and then back on. After a few moments it will connect with both the music device and phone.
Any Bluetooth Enabled Audio Device*

Call Button Indicator

MUSIC CONTROLS

Left Side

Volume

Buttons

TROUBLESHOOTING
Are you having sound interruption or connection issues?

Right Side

Skip Reverse Skip Forward Headphone Jack Music Button

WEAR THE HEADPHONES

6809496A47-A
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. Motorola, Inc. 2005.
Your headphones are designed to be worn comfortably with the neck band positioned behind your head. The microphone is located in the right ear-piece. Digital Signal processing is used for clear pickup of your voice during voice calls.

Note: The remote control functions only work when the headphones are directly connected to source device. via Bluetooth.
To adjust the volume, press the + or - buttons on the left side of your headphones. To Skip Back to the previous song: Press the Skip Reverse Button < on the right side of your headset. To Skip forward to the next song: Press the Skip Forward Button > To Play, Pause, or Stop music: Press the Music Button M to play, pause, or stop the music. To connect non-Bluetooth Devices to your headphones: Use the headphone jack and the included cable.
Bluetooth as a wireless technology could be subject to interference of other wireless traffic existing in your environment. Try turning your headphone off and back on. This automatically resets the connection. If you experience audio interruptions while the headphone is connected to both music source and a Bluetooth phone, disconnecting the phone will eliminate the audio interruptions.
Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.hellomoto.com/bluetooth and click Support.
Features and Functions Guide

PAIR with YOUR PHONE

START BLUETOOTH Feature
PUT HEADPHONES IN PAIRING
Make sure your headphones are turned off. If your headset is on, turn it off by pressing and holding the left side Call m button until the indicator light flashes 3 times (about 3 seconds).
Music Button with Indicator Light (Right Side)
Step B SET THE PHONE TO LOOK FOR YOUR HEADPHONES
For most Motorola phones:
Your Headphones & Phone
Your phone's Bluetooth feature is off by default. So, to use your headset, you must turn on the Bluetooth feature in your phone. For most Motorola phones: 1 Select M (Menu ) > Settings > Connection >
1 Select M (Menu ) > Settings > Connection >
Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds. 2 Select Motorola HT820. device. 4 Enter the passkey 0000 and press OK. Note: Passkey cannot be changed from 0000.
Your phone and headphones are now paired and ready to make and receive calls. To confirm they are operating properly, make a call:

1 Place the headphones over your ear. See
Wear the Headset on the reverse side of this guide. to call and press the Send key.
Bluetooth Link > Setup.
3 Press OK or Yes to pair (link) the handsfree
2 On your phone, dial the number you want 3 If your phone and headphones are
successfully paired, you will hear ringing in the headphones.
IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your HT820.
FOR MORE INFORMATION ON USING YOUR MOTOROLA HT820 Visit us at www.hellomoto.com/bluetooth and click Support. SUPPORT If you need more help, contact us at 1-877-MOTOBLU.
2 Scroll to Power. 3 Press Change. 4 Scroll to On. 5 Press Select to turn on the Bluetooth
feature. Bluetooth feature remains on until you turn it off.
Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.
When your headphones are successfully paired with your phone, the blue indicator light rapidly flashes and then resumes regular flashing.
Note: For more details, see "Pair," Step 1 on the reverse side of this guide.
See Make Calls for details regarding answering and ending calls using the headset. After you have successfully paired your phone and headphones, you do not need to repeat these initial setup steps each time you use the headphones. Just turn the power on and they will automatically connect.

MAKE CALLS

Function Make a voice dial call Action Short press left m button & speak the name after the tone Short press left m button Short press left m button Long press left m button until ringing stops. Call ignored. Long press left m button Press and hold the Call button (places first call on hold)

MAKE CALLS CONTINUED

Function Use Call Waiting Action Long press left m button, 1st call put on hold. 2nd call becomes active. Press both volume buttons + at the same time. Both calls become active. Long press left m button Press the volume buttons + at the same time. Press either the + or the to unmute the mic.

INDICATOR LIGHTS

The indicator light provides information about your headphone status. With the Charger Plugged In Headphone Indicator Status On (steady) Charging Off Charging complete With No Charger Plugged In Headphone Indicator Off On (steady) 10 rapid flashes Slow pulse

AUDIO TONES

The audio tones provide information about your headphone status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 60 sec. No audio indications; deteriorating quality Ring tone Single high tone Single low tone Dual high/low tone Single high tone Low to high tone Two tones Single tone Headphone Status Volume at minimum or maximum Low battery Out of range Incoming call Pairing confirmation Voice activation Voice tag not recognized End call Phone network not available Mute on / off Power on / off

End a call Receive a call Reject a call
Join a 3-way call (Note: Feature is phone/ network dependent.)
Redial last call Answer a second incoming call
This symbol on a Motorola product means the product should not be disposed of with household waste. Please do not dispose of mobile telephones or electric accessories, such as chargers or headsets, with your household waste.
Put an active call on hold or resume a call on hold Mute a call
Status Power off Pairing mode Pairing successful Connected
Note: Your HT820 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.

Unmute a call

To turn off the indicator lights, press both < and > at the same time. To turn the indicator lights back on, press both <and > at the same time.

MOTOROLA BLUETOOTH STEREO SYSTEM GET TO KNOW

Unobtrusive Neck Wrap

Forget your headphones are there with this ergonomic design; already lightweight, this feature minimizes pressure and maximizes comfort
MOTOROLA BLUETOOTH Stereo System
Motorola Bluetooth Stereo Headphones HT820
Phone Controls Pairing Button
Motorola Bluetooth Home Stereo Adapter DC800 Motorola Bluetooth Stereo PC Adapter PC850

Advanced Volume Buttons

Ultra Ergonomic Earpiece 3.5mm Headset Jack
Use the in-the-box accessory cable when on an airplane
Cushioned earpiece for comfort, background noise-reduction and snug listening pleasure
Music Controls Play/Pause Button and LED Indicator Light
Skip tracks or control playlists
At-a-glance status light; push to play or pause
Power Button Audio In and Audio Out Connections
Easily connect to your home audio system

Integrated Feet

Allows 2 different positions
Blue LED Status Indicator Light

At-a-glance status light

The Details
Bulk Kit Retail Part Number: Part Number: MSRP:

HT820: DC800: PC850:

SYN0948D SYN1001A SYN1244B

98689H 98690H 98716H

$ 119.99 $ 99.99 $ 49.99
USB Universal Compatibility Snug-fit Protector
Fits into any standard USB port on your PC or Mac; designed per USB industry standards
Keeps it dust-free and clean when not in use
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. Other trademarks and trade names are those of their respective owners. Motorola, Inc. 2006. All rights reserved. BIM-2245

HELLOMOTO.COM/BLUETOOTH

877 MOTOBLU
Motorola Bluetooth Stereo Headphones HT820
enabled music sources including the DC800, PC850 and Ten iPod adapter1 Convenient call alert - music automatically pauses when a call is received and resumes when the call ends Embedded microphone for phone conversations Lightweight, comfortable and ergonomic fit Noise-reduction microphone minimizes background noise Up to 14 hours music listening and 17 hours phone talk time Simple controls for phone and music functions discretely integrated into unique design 3.5mm headset jack and accessory cable come in the box - can be used on airplanes Compatible with non-Bluetooth devices for universal music enjoyment Compatible with Bluetooth 1.2 devices for voice calls Bluetooth A2DP/AVRCP devices for listening and controlling music
Simultaneously connects your compatible Bluetooth-enabled phone with a variety of Bluetooth-
Motorola Bluetooth Home Stereo Adapter DC800
Streaming from DC800 allows the user to stream to your Bluetooth enabled headset2 Streaming to DC800 from your Bluetooth enabled phone, PC, audio device or to your home stereo system Connect to your home audio system via included standard audio jacks (RCA and 3.5mm cables are included in the box) Only works with an audio device with standard RCA audio connections or 3.5mm headset connection (not all Groundbreaking Music System Trio of Bluetooth-enabled products integrates music Bluetooth A2DP devices for listening to music and Bluetooth AVRCP for play/pause function only (DC800 supports
devices using 0000 pairing PIN code) stereo devices support an auxiliary or RCA jack)
Te a r th i s p a ge o ff a n d p o s t i t fo r q u i ck re fe re n c e !
New suite of Bluetooth wireless-enabled products merges wire-free mobility with musical entertainment
enjoyment and wireless communication
Leveraging the power of Bluetooth technology to
connect your devices for maximum music enjoyment
Motorola Bluetooth Stereo PC Adapter PC850
Enables your computer to stream music to your compatible Bluetooth-enabled headphones - no cords or wires necessary3 Eliminates cable clutter Empowers traditional laptops and PCs with Bluetooth technology, establishing cordless connections to compatible Bluetooth-enabled
mobile phones, headsets and PDAs4 Whether used to share and stream music files, data or images, the PC adapter provides a new level of mobile convenience Requires Windows 98 SE, 2000, ME or XP operating systems, 350 MHz or higher processor and an available USB port; this product will disable any factory installed Bluetooth hardware and software on your PC

Use both the Motorola PC850 and the DC800 to stream
music from your computer to play on your stereo, and add the HT820 to stream to your headphones
Range up to 10 meters (30 feet) giving you plenty of
room to wirelessly connect, move and groove
1 The Stereo Headphones HT820 support Bluetooth (INSERT) profiles. Your compatible Bluetooth phone and accessories must support these profiles. To determine the compatibility of Motorola phones/accessories, visit the customer support page at www.hellomoto.com. For other phones/accessories, contact the manufacturer. 2 The Stereo Adapter DC800 supports Bluetooth (INSERT) profiles. Your compatible Bluetooth phone and accessories must support these profiles. To determine the compatibility of Motorola phones/accessories, visit the customer support page at www.hellomoto.com. For other phones/accessories, contact the manufacturer. 3 Music only. Voice calls are not supported on the headphones when using your computer and the PC adapter. For optimal use, power off the Bluetooth feature in your handset when listening to music. 4 The PC Adapter PC850 supports Bluetooth (INSERT) profiles. Your compatible Bluetooth phone and accessories must support these profiles. To determine the compatibility of Motorola phones/accessories, visit the customer support page at www.hellomoto.com. For other phones, contact the manufacturer.