BEFORE YOU BEGIN

Start Here > > >
Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions.

Your Headset's Battery

CHARGE

START BLUETOOTH Feature

On Your Phone

TROUBLESHOOTING

My phone does not find my headset. Make sure the blue light on your headset is steadily lit when your phone is searching for devices (see step 3). My headset worked before but now it's not working. Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature has been turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2). If you have confirmed the Bluetooth feature is on in your phone, pair your phone and headset again (see step 3). Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.hellomoto.com/bluetooth and click Support
Charge your headset's battery for 2 hours:
H500 Bluetooth Handsfree Headset
Get Connected in 4 Quick Steps
1 - CHARGE 2 - START BLUETOOTH FEATURE 3 - PAIR 4 - TEST AND USE
Take a moment before you get started to familiarize yourself with your new H500 Handsfree Headset.

Earhook Volume Buttons

Your phone's Bluetooth feature is off by default. To use your headset, turn on the Bluetooth feature in your phone. For most Motorola phones: (Menu 1 Select M( ) > Settings > Connection >
Bluetooth Link > Setup.
1 Plug the Motorola charger into the end of

Call Button

the headset.
2 Scroll to Power. 3 Press Change. 4 Scroll to On. 5 Press Select to turn on the Bluetooth
feature. Bluetooth feature remains on until you turn it off.

Blue Indicator Light

The blue indicator light turns on when the battery is charging. It may take up to 1 minute for the light to turn on. When the headset's battery is fully charged (about 2 hours), the blue indicator light turns off.
2 Unplug the charger from the headset.

Microphone

Note: Headset is not functional while charging.
Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide.
Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 USA www.hellomoto.com 1-877-MOTOBLU 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada) Guide Number: 6809494A56-A If you need more help, contact us at 1-877-MOTOBLU.

Your Headset

Your Phone Step B - SET THE PHONE TO LOOK FOR YOUR HEADSET For most Motorola phones: (Menu 1 Select M( ) > Settings > Connection >

TEST AND USE

USING YOUR H500
See Features and Functions Guide on the reverse side of this guide for information on using your H500.
Step A - PUT HEADSET IN PAIRING MODE Before you can use your headset, you must pair (link) it with your phone.
Call Button Blue Indicator Light
Your phone and headset are now paired and ready to make and receive calls. To confirm they are operating properly, make a call:
Bluetooth Link > Handsfree > Look for Devices.
1 Place the headset over your ear. See
The phone lists all Bluetooth devices it finds. 2 Select Motorola H500. device. Enter the passkey 0000 and press OK. 4 Note: Passkey cannot be changed from 0000.
"Wearing the Headset" on the reverse side of this guide. to call and press the Send key.

1 With the headset power off, press and hold
the Call button for 6 to 10 seconds until the blue indicator light turns on and remains steadily lit. (The light will flash while you hold the Call button.) remain steadily lit, turn off the headset and repeat step 1.
3 Press OK or Yes to pair (link) the handsfree
2 On your phone, dial the number you want 3 If your phone and headset are successfully
paired, you will hear ringing on the headset.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. Motorola, Inc. 2005.
2 If the indicator light is flashing or does not
When your headset is successfully paired with your phone, the blue indicator light changes from steadily lit to flashing.
After you have successfully paired your phone and headset, you do not need to repeat these initial setup steps each time you use the headset.
Note: To turn off headset, see "Turning On and Off" on the reverse side of this guide.
Features and Functions Guide

TURNING ON AND OFF

To turn your headset on, press and hold the Call button until the indicator light flashes. Then, release the button. To turn your headset off, press and hold the Call button until the indicator light flashes rapidly and then turns off. To conserve battery power, turn off your headset when you don't plan to use it for a while.

WEARING THE HEADSET

1 Open the earhook. 2 Loop the earhook over your ear. 3 Press the headset to your ear.
CHANGING FOR USE ON OTHER EAR
You can wear your H500 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:
CHANGING VOLUME BUTTON ORIENTATION
If you change your headset to wear on the other ear, you can also change the orientation of the volume buttons.

1 Open the earhook 90

degrees from the headset.

040059o

1 Turn the headset power off. 2 Press the Call button and the volume
button you want to assign as the "volume up" button until the indicator light flashes twice. The headset power turns on.

Volume Buttons

2 Gently lift and pull the
IMPORTANT: Be sure to first follow the Quick Start Guide on the reverse side of this guide to complete initial setup of your H500.
FOR MORE INFORMATION ON USING YOUR MOTOROLA H500 Visit us at www.hellomoto.com/bluetooth and click Support. SUPPORT If you need more help, contact us at 1-877-MOTOBLU.

top of the earhook up and off the upper hinge pin. Then, pull it away to remove it.

1 Open Earhook

2 Pull Earhook Up
3 Flip the headset over. 4 Hook the bottom of the 3 4

Call Button Hinge Pin

earhook onto the lower hinge pin, then lift and pull the top of the earhook over the upper hinge pin.

MAKING CALLS

Function Make a voice dial call End a call Receive a call Reject a call Redial last call Answer a second incoming call Action Tap the Call button and speak the name after the tone Tap the Call button Tap the Call button Press and hold the Call button until you hear a beep Press and hold the Call button until you hear a beep Press and hold the Call button (places first call on hold)

MAKING CALLS CONTINUED

Function Toggle between two active calls Join a 3-way call Put an active call on hold or resume a call on hold Transfer a call from the phone to the headset Disable or enable the indicator light Mute or unmute a call Action Press and hold the Call button Press and hold both Volume buttons Press and hold the Call button until you hear a beep Tap the Call button Press and hold both Volume buttons for 3 to 4 seconds Tap both Volume buttons

INDICATOR LIGHTS

The indicator light provides information about your headset status. With the Charger Plugged In Headset Indicator Headset Status On (steady) Charging Off Charging complete With No Charger Plugged In Headset Indicator Off On (steady) 10 rapid flashes Slow pulse Quick flash Headset Status Power off Pairing mode Pairing successful Connected (on a call) Standby (not on call)
The audio tones provide information about your headset status. Audio Tone Single high tone when pressing volume button Five rapid high tones repeated every 60 sec. No audio indications; deteriorating quality Ring tone Single high tone Single low tone Dual high/low tone Single high tone Low to high tone Two ascending tones Two descending tones Headset Status Volume at minimum or maximum Low battery Out of range Incoming call Pairing confirmation Voice activation Voice tag not recognized End call Phone network not available Mute enabled Mute enabled

AUDIO TONES

Note: Your H500 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information.

Note: Some features are phone/network dependent.
Note: After 5 minutes of inactivity, the light stops flashing to conserve power, but the headset remains in standby mode.

And Making VoIP Calls

The following steps describe how to install the software on a computer running the Microsoft Windows XP operating system. Minor differences exist when installing this software on other Windows operating systems.
Stop all running programs and insert the installation CD into the CD-ROM drive. The installation starts automatically and guides you through the installation. If the installation does not start automatically, find the SETUP.exe file on the CD and double click it to start the installation.
www.hellomoto.com/bluetooth

6809495A86-A

or call the Motorola Help desk at: 1-877-MOTOBLU (1-877-668-6258)
Welcome to Bluetooth software.
Accept license agreement.
Confirm or change software destination location.

Start installation.

Installation begins.
Bluetooth device not found message displays. Do NOT respond until you install the adapter.
Insert adapter into USB port. Click OK in Bluetooth device message (see step 7) if installation does not continue.
Complete the installation and restart your computer.
Verify Bluetooth adapter is ready to receive and transmit data (LED is solid blue).

Right click Bluetooth.

and select Start Using

Start Using Bluetooth

Complete the initial Bluetooth configuration wizard.
Enter computer information and click Next. On the Initial Bluetooth Configuration wizard window, click Next.
Select and configure services.
To configure another device, click Next. Otherwise, click Skip. Click Finish.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. Microsoft, Windows, ActiveSync, Windows Media, and MSN are registered trademarks of Microsoft Corporation; and Windows XP, Windows Mobile and Microsoft.net are trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. www.hellomoto.com
Continue steps on other side >

16 Pairing with your

Bluetooth Device
Open Bluetooth Explorer by double clicking My Bluetooth Places on your computer desktop.
Make sure your Bluetooth device is powered on and can be found.
For the H500 Headset: To prepare the H500 headset to be found, make sure it is powered off. Then press and hold the Call (center) button until the blue light remains solidly lit.
On your computer, search for Bluetooth devices. Make sure the device you want to communicate with is on and can be found. (i.e. H500 headset).
Right click the device and select Pair Device.
For Motorola headsets: Enter the 4-digit PIN code 0000 and click OK.
Press and Hold until light remains solidly lit.
Motorola H500 Audio Headset
For other Bluetooth devices: Refer to the devices User Guide for detailed information about making the device discoverable (putting it in Pairing Mode).

For all other devices: Follow the prompts for the device. When prompted for a PIN code, enter the code specified in the device User Guide (for Motorola devices, this code is usually 0000 or 1234). The code must be the same on both paired (bonded) devices.
A check mark displays next to the device icon indicating a successful pairing (bond). Bluetooth services are now ready to used.

Making VoIP Calls

Right click the audio device icon and select Connect Headset.
When the device is successfully connected, the icon turns green.
Launch the VoIP program and initiate a call. The VoIP call audio is routed to your Bluetooth headset. Note: If no audio is heard through the Bluetooth headset then, manually set the audio settings of the VoIP program to be Bluetooth Audio.
Using a Bluetooth Headset or audio device and computer, you can make Voice over IP (VoIP) calls. The following steps describe how to make VoIP calls.
Double-click the Bluetooth audio device icon (that was paired with the computer in step 21).

Motorola H500

Headset on Motorola H500 Not Connected
To set Bluetooth Audio manually when using Skype: Go to the Tools menu, select Options, and then Sound Devices. Note: The headset will beep. Press the Call (center) button once to complete the connection. Not all features of Bluetooth headset may be available during VoIP calls. Note: Pressing the headset Call (center) button disconnects the headset from the computer but may not end the call.
Double-click the Bluetooth Audio Device Icon.
When reconnecting your Bluetooth headset to the computer, turn the headset on. The headset will beep. Press the Call (center) button once to complete the connection.
Bluetooth Explorer Quick Tips
Find Bluetooth Devices Looks for other Bluetooth devices.
For additional assistance visit our website at:
If the headset does not automatically connect: On the computer system tray, right click the symbol and select Quick Connect and then Headset.
To open Bluetooth Explorer, click My Bluetooth Places on your desktop, or double click in the system tray. Bluetooth Setup Wizard Configures devices, connections, and local services. Entire Bluetooth Neighborhood Displays Bluetooth adapter devices.

My Device Displays services on this computer. Bluetooth Exchange Folder Contains files and folders available to remote Bluetooth adapter devices.
For more information on how to use this software, see the product Help files for each screen of the software.
For additional assistance using Skype visit: http://support.skype.com
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. Microsoft, Windows, ActiveSync, Windows Media, and MSN are registered trademarks of Microsoft Corporation; and Windows XP, Windows Mobile and Microsoft.net are trademarks of Microsoft Corporation. All other product or service names are the property of their respective owners. www.hellomoto.com 2005 Motorola Inc.